51
|
Tordi P, Gelli R, Ridi F, Bonini M. A bioinspired and sustainable route for the preparation of Ag-crosslinked alginate fibers decorated with silver nanoparticles. Carbohydr Polym 2024; 326:121586. [PMID: 38142067 DOI: 10.1016/j.carbpol.2023.121586] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/30/2023] [Revised: 10/17/2023] [Accepted: 11/10/2023] [Indexed: 12/25/2023]
Abstract
Functional materials obtained through green and sustainable routes are attracting particular attention due to the need to reduce the environmental impact of the chemical industry. In this work we propose a bioinspired approach for the preparation of alginate fibers containing silver nanoparticles (AgNPs), to be used for antimicrobial purposes. We demonstrate that filiform polymeric structures with length of a few meters can be easily obtained by extruding an alginate solution in an aqueous Ag+-containing bath (i.e. wet spinning) and that treating the fibers with freshly-squeezed lemon juice leads to the formation of AgNPs homogeneously distributed within the polymeric network. Using mixtures of ascorbic and citric acid to mimic lemon juice composition we highlight the influence of the aforementioned molecules on the nanoparticles formation process as well as on the properties of the fibers. Varying the amount of citric and ascorbic acid used for the treatment allows to finely tune the thermal, morphological and water absorption properties of the fibers. This evidence, along with the possibility to easily monitor the preparation through FT-IR spectroscopy, endows the fibers with a high application potential in several fields such as wound healing, water/air purification and agriculture.
Collapse
|
52
|
Vakilian S, Al-Hashmi S, Al-Kindi J, Al-Fahdi F, Al-Wahaibi N, Shalaby A, Al-Riyami H, Al-Harrasi A, Jamshidi-Adegani F. Avastin-loaded 3D-printed Alginate Scaffold as an Effective Anti-Adhesive Barrier to Prevent Post-Surgical Adhesion Bands Formation. Macromol Biosci 2024:e2300530. [PMID: 38319279 DOI: 10.1002/mabi.202300530] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/19/2023] [Revised: 01/18/2024] [Indexed: 02/07/2024]
Abstract
Post-operative adhesion can cause complications, such as pain, and organ blockage, in the abdominal regions. To address this issue, surgical techniques, and anti-adhesive treatments have been applied. Given the significant role of vascularization in adhesion band formation, Avastin (Ava) that targets VEGF can be applied to prevent peritoneal adhesion bands. Moreover, Alginate (Alg), a natural polysaccharide, is a promising physical barrier to prevent adhesion bands. Incorporating Ava into Alg hydrogel in a form of 3D-printed scaffold (Alg/Ava) has potential to suppress inflammation and angiogenesis, leading to reduce peritoneal adhesion bands. Following physical, morphological, and biocompatibility evaluations, the efficacy of Alg and Ava alone and their combination in Alg/Ava on the formation of post-surgical adhesions was evaluated. Upon confirming physical stability and sustained release of Ava, the Alg/Ava scaffold effectively diminished both the extent and strength of adhesion bands. Histopathological examination showed that the reduction in fibrosis and inflammation was responsible for preventing adhesion bands by the Alg/Ava scaffold. Additionally, the cytokine assessment revealed that this was due to the inhibition in the secretion of VEGF and IL-6, suppressing vascularization and inflammatory pathways. This study suggests that a 3D-printed Alg/Ava scaffold has great potential to prevent the post-surgical adhesion bands. This article is protected by copyright. All rights reserved.
Collapse
|
53
|
Takbirgou H, Salami M, Askari G, Emam-Djomeh Z, Kennedy JF. Characterization of novel alginate-Aloe Vera raft systems for treatment of gastroesophageal reflux disease. Int J Biol Macromol 2024; 257:128686. [PMID: 38092117 DOI: 10.1016/j.ijbiomac.2023.128686] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/03/2023] [Revised: 12/01/2023] [Accepted: 12/06/2023] [Indexed: 12/18/2023]
Abstract
Raft-forming systems are designed to relieve reflux symptoms by forming a physical barrier on top of the stomach. The present study aimed to evaluate the physico-chemical properties of alginate-aloe vera raft-forming systems for the first time. To achieve this goal, aloe vera was used in the proportion of 1 and 1.5 % in raft suspensions containing 5 % alginate as the main component of gel structure. Rafts were characterized by their volume, floating behavior, thickness, swelling properties, strength, resilience, reflux resistance, and acid neutralization capacity (ANC). Results showed the effectiveness of aloe vera in forming rafts that were voluminous, buoyant with greater total floating time (TFT), and stronger than formulations with no aloe vera. Furthermore, data showed that the presence of aloe vera could improve resilience time, swelling proportions, resistance to reflux under simulant conditions of movement in the stomach, and ANC values of rafts. Rafts were further characterized by oscillatory strain sweep test, differential scanning calorimetry, and Fourier transform infrared spectroscopy. Evaluation of the mechanical properties of rafts displayed a viscoelastic behavior of gels corresponding to the internal cross-linked structure of rafts. This study demonstrated that designing of alginate-aloe vera rafts can be suitable for the treatment of gastro-esophageal reflux disorders.
Collapse
|
54
|
Cao L, Verduijn J, Van der Meeren L, Huang Y, Vallejos LC, Skirtach AG, Parakhonskiy BV. Alginate-CaCO 3 hybrid colloidal hydrogel with tunable physicochemical properties for cell growth. Int J Biol Macromol 2024; 259:129069. [PMID: 38161005 DOI: 10.1016/j.ijbiomac.2023.129069] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/20/2023] [Revised: 12/13/2023] [Accepted: 12/25/2023] [Indexed: 01/03/2024]
Abstract
Biomaterials composed of food polysaccharides are of great interest for future biomedical applications due to their great biocompatibility, tunable mechanical properties, and complex architectural designs that play a crucial role in the modulation of cell adhesion and proliferation. In this work, a facile approach was designed to obtain novel 3D alginate-CaCO3 hybrid hydrogel particles in situ. Controlling the gel concentration from 3 to 20 mg·mL-1 allows us to control the alginate-CaCO3 hydrogel particles' size and density (size variation from 1.86 to 2.34 mm and density from 1.22 to 1.29 mg/mm3). This variable also has a considerable influence on the mineralization process resulting in CaCO3 particles with varied sizes and amounts within the hydrogel beads. The measurements of Young's modulus showed that the inclusion of CaCO3 particles into the alginate hydrogel improved its mechanical properties, and Young's modulus of these hybrid hydrogel particles had a linear relationship with alginate content and hydrogel particle size. Cell experiments indicated that alginate-CaCO3 hybrid hydrogel particles can support osteoblastic cell proliferation and growth. In particular, the amount of hydroxyapatite deposition on the cell membrane significantly increased after the treatment of cells with hybrid hydrogel particles, up to 20-fold. This work offers a strategy for constructing inorganic particle-doped polysaccharide hybrid hydrogel scaffolds that provide the potential to support cell growth.
Collapse
|
55
|
Lee HK, Woo S, Baek D, Min M, Jung GY, Lim HG. Direct and robust citramalate production from brown macroalgae using fast-growing Vibrio sp. dhg. BIORESOURCE TECHNOLOGY 2024; 394:130304. [PMID: 38211713 DOI: 10.1016/j.biortech.2024.130304] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/22/2023] [Revised: 12/29/2023] [Accepted: 01/06/2024] [Indexed: 01/13/2024]
Abstract
Brown macroalgae is a promising feedstock for biorefinery owing to its high biomass productivity and contents of carbohydrates such as alginate and mannitol. However, the limited availability of microbial platforms efficiently catabolizing the brown macroalgae sugars has restricted its utilization. In this study, the direct production of citramalate, an important industrial compound, was demonstrated from brown macroalgae by utilizing Vibrio sp. dhg, which has a remarkably efficient catabolism of alginate and mannitol. Specifically, citramalate synthase from Methanocaldococcus jannaschii was synthetically expressed, and competing pathways were removed to maximally redirect the carbon flux toward citramalate production. Notably, a resulting strain, VXHC, produced citramalate up to 9.8 g/L from a 20 g/L mixture of alginate and mannitol regardless of their ratios. Citramalate was robustly produced even when diverse brown macroalgae were provided directly. Collectively, this study showcased the high potential of brown macroalgae biorefinery using Vibrio sp. dhg.
Collapse
|
56
|
Gennari A, Simon R, Renard G, Chies JM, Volpato G, Volken de Souza CF. Lactose hydrolysis in packed-and fluidized-bed reactors using a recombinant β-galactosidase immobilized on magnetic core-shell capsules. Bioprocess Biosyst Eng 2024; 47:263-273. [PMID: 38156992 DOI: 10.1007/s00449-023-02960-8] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/10/2023] [Accepted: 12/06/2023] [Indexed: 01/03/2024]
Abstract
The objective of this study was to develop a bioprocess for lactose hydrolysis in diverse dairy matrices, specifically skim milk and cheese whey, utilizing column reactors employing a core-shell enzymatic system featuring β-galactosidase fused to a Cellulose Binding Domain (CBD) tag (β-galactosidase-CBD). The effectiveness of reactor configurations, including ball columns and toothed columns operating in packed and fluidized-bed modes, was evaluated for catalyzing lactose hydrolysis in both skim milk and cheese whey. In a closed system, these reactors achieved lactose hydrolysis rates of approximately 50% within 5 h under all evaluated conditions. Considering the scale of the bioprocess, the developed enzymatic system was capable of continuously hydrolyzing 9.6 L of skim milk while maintaining relative hydrolysis levels of approximately 50%. The biocatalyst, created by immobilizing β-galactosidase-CBD on magnetic core-shell capsules, exhibited exceptional operational stability, and the proposed bioprocess employing these column reactors showcases the potential for scalability.
Collapse
|
57
|
Naskar P, Chakraborty D, Mondal A, Das B, Samanta A. Immobilization of α-amylase in calcium alginate-gum odina (CA-GO) beads: An easily recoverable and reusable support. Int J Biol Macromol 2024; 258:129062. [PMID: 38159691 DOI: 10.1016/j.ijbiomac.2023.129062] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/19/2023] [Revised: 12/13/2023] [Accepted: 12/24/2023] [Indexed: 01/03/2024]
Abstract
A natural polysacharide, gum odina was collected from Odina wodier tree and purified. Purified gum odina was used with sodium alginate for immobilization of α-amylase. Calcium alginate-gum odina (CA-GO) beads were prepared by ionotropic gelation method to find the improvement of immobilization efficiency and reusability of α-amylase over calcium alginate (CA) beads. XRD, SEM, FTIR, beads diameter, enzyme leaching from beads, moisture content, total soluble matter and swelling study have been carried out to understand the physical morphology and mechanism of immobilization of enzyme in beads matrix. It has been observed that if the polymer ratio changes (keeping enzyme conc. & calcium Chloride conc. constant) then the size and shape of the beads will vary and at a particular range of polymer ratio, the optimal beads forms. At a certain conc.(4%w/v of SA and 1%w/v GO), the immobilization efficiency of CA-GO and CA beads were 92.71 ± 0.85 % (w/w) and 89.19 ± 0.35 %(w/w) respectively. After 8th time use, the CA-GO beads remain (~4 fold) more active than that of CA beads. The FTIR confirms that GO does not interfere with α-Amylase and alginate. Here, it can be concluded that CA-GO beads show better efficiency in respect to immobilization, reusability than CA beads only.
Collapse
|
58
|
Ivanovska A, Milošević M, Lađarević J, Jankoska M, Matić T, Svirčev Z, Kostić M. A step towards tuning the jute fiber structure and properties by employing sodium periodate oxidation and coating with alginate. Int J Biol Macromol 2024; 257:128668. [PMID: 38092097 DOI: 10.1016/j.ijbiomac.2023.128668] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/13/2023] [Revised: 11/20/2023] [Accepted: 12/06/2023] [Indexed: 12/17/2023]
Abstract
This paper outlines a novel simple protocol for tuning the structure and properties of jute using sodium periodate (NaIO4) oxidation and coating with alginate. When compared to the raw jute, fabrics oxidized with a 0.2 or 0.4 % NaIO4 solution for 30-120 min exhibited an increased aldehyde group content (0.185 vs. 0.239-0.398 mmol/g), a significantly increased negative zeta potential (from -8.57 down to -20.12 mV), a slight disruption of fiber crystallinity, 15.1-37.5 % and 27.9-49.8 % lower fabric maximum force and stiffness, respectively. Owing to the removal of hydrophobic surface barrier, decreased crystallinity index and the presence of micropores on the fabrics' surfaces, oxidized fabrics have a 22.3-29.6 % improved ability for moisture sorption compared to raw fabric. Oxidized fabrics characterized by very long wetting times and excellent antioxidant activities (> 98 %), can find applications as hydrophobic packaging materials. To further extend the utilization of jute in biocarpet engineering such as water-binding geo-prebiotic supports, oxidized fabrics were coated with alginate resulting in 7.9-24.9 % higher moisture sorption and 352-660 times lower wetting times than their oxidized counterparts. This modification protocol has never been applied to lignocellulosic fibers and sheds new light on obtaining jute fabrics with tuned structure and properties intended for various applications.
Collapse
|
59
|
Bider F, Miola M, Clejanu CE, Götzelmann J, Kuth S, Vernè E, Basu B, Boccaccini AR. 3D bioprinting of multifunctional alginate dialdehyde (ADA)-gelatin (GEL) (ADA-GEL) hydrogels incorporating ferulic acid. Int J Biol Macromol 2024; 257:128449. [PMID: 38029911 DOI: 10.1016/j.ijbiomac.2023.128449] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/11/2023] [Revised: 10/17/2023] [Accepted: 11/20/2023] [Indexed: 12/01/2023]
Abstract
The present work explores the 3D extrusion printing of ferulic acid (FA)-containing alginate dialdehyde (ADA)-gelatin (GEL) scaffolds with a wide spectrum of biophysical and pharmacological properties. The tailored addition of FA (≤0.2 %) increases the crosslinking between FA and GEL in the presence of calcium chloride (CaCl2) and microbial transglutaminase, as confirmed using trinitrobenzenesulfonic acid (TNBS) assay. In agreement with an increase in crosslinking density, a higher viscosity of ADA-GEL with FA incorporation was achieved, leading to better printability. Importantly, FA release, enzymatic degradation and swelling were progressively reduced with an increase in FA loading to ADA-GEL, over 28 days. Similar positive impact on antibacterial properties with S. epidermidis strains as well as antioxidant properties were recorded. Intriguingly, FA incorporated ADA-GEL supported murine pre-osteoblast proliferation with reduced osteosarcoma cell proliferation over 7 days in culture, implicating potential anticancer property. Most importantly, FA-incorporated and cell-encapsulated ADA-GEL can be extrusion printed to shape fidelity-compliant multilayer scaffolds, which also support pre-osteoblast cells over 7 days in culture. Taken together, the present study has confirmed the significant potential of 3D bioprinting of ADA-GEL-FA ink to obtain structurally stable scaffolds with a broad spectrum of biophysical and therapeutically significant properties, for bone tissue engineering applications.
Collapse
|
60
|
Araujo Neto LA, Silva LP. Influence of biopolymer composition and crosslinking agent concentration on the micro- and nanomechanical properties of hydrogel-based filaments. J Mech Behav Biomed Mater 2024; 150:106316. [PMID: 38145614 DOI: 10.1016/j.jmbbm.2023.106316] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/06/2023] [Revised: 08/08/2023] [Accepted: 12/10/2023] [Indexed: 12/27/2023]
Abstract
Hydrogel filaments were manufactured using wet spinning technique, incorporating variations in the concentrations of sodium alginate, gelatin, and calcium chloride (crosslinking agent). The combination of biopolymer concentrations was determined using design of experiments (DoE) approach. The resulting filaments were produced from the developed hydrogels. Tensile and vertical strength analyses of the filaments were conducted using an electromechanical extensor. Atomic force microscopy was employed to evaluate the roughness, viscoelasticity, retraction, and deflection of the hydrogels. By employing DoE, a total of seventeen different combinations of biopolymers and crosslinkers were generated to construct the hydrogels. The filaments exhibited variations in electromechanical traction (measured in kPa) and produced distinct stress peaks. Furthermore, diverse roughness values were observed among the tested materials, with the combinations featuring higher concentrations of sodium alginate displaying the highest Young's modulus. This study demonstrates that manipulating the concentrations of biopolymers and crosslinking agents can modulate the micro and nanomechanical properties of biopolymeric filaments.
Collapse
|
61
|
Dananjaya SHS, Bandara N, Molagoda IMN, Sandamalika WMG, Kim D, Ganepola N, Attanayake AP, Choi D. Multifunctional alginate/polydeoxyribonucleotide hydrogels for promoting diabetic wound healing. Int J Biol Macromol 2024; 257:128367. [PMID: 38029897 DOI: 10.1016/j.ijbiomac.2023.128367] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/09/2023] [Revised: 11/15/2023] [Accepted: 11/21/2023] [Indexed: 12/01/2023]
Abstract
A multifunctional alginate/PDRN hydrogel system by ionic crosslinking and the Schiff base reaction between oxidized alginate (OA) and PDRN was developed in the present study. Biocompatibility assessment of the PDRN-loaded OA hydrogels showed a significant enhancement in cell viability in human dermal fibroblast (HDF) cells. In addition, hydrogels showed migratory, anti-inflammatory, intracellular reactive oxygen species scavenging, and anti-apoptotic activities. In vivo studies using a streptozotocin-induced diabetic Wister rat model indicated that OA-4PDRN had the highest percentage of wound closure (96.1 ± 2.6 %) at day 14 compared to the control (79.0 ± 2.3 %) group. This was accompanied by up-regulation of vascular endothelial growth factor (VEGF), interleukin-10 (IL-10), and transforming growth factor-beta (TGF-β) accompanied by down-regulation of pro-inflammatory markers (IL-6, IL-1β). Following histopathological observations, PDRN-loaded OA hydrogel ensured tissue safety and induced wound healing with granular tissue formation, collagen deposition, re-epithelialization, and regeneration of blood vessels and hair follicles. The downregulation of inflammatory cytokines (CD68) and expression of angiogenesis-related cytokines (CD31) in wound sites revealed the suppression of inflammation and increased angiogenesis, ensuring skin tissue regeneration in diabetic wound healing. In conclusion, the findings suggest that PDRN-loaded OA hydrogel has enormous therapeutic potential as a diabetic wound dressing.
Collapse
|
62
|
Steiger BGK, Wilson LD. Biopolymer-metal composites for selective removal and recovery of waterborne orthophosphate. CHEMOSPHERE 2024; 349:140874. [PMID: 38061562 DOI: 10.1016/j.chemosphere.2023.140874] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 07/22/2023] [Revised: 11/28/2023] [Accepted: 11/30/2023] [Indexed: 01/10/2024]
Abstract
Orthophosphate (Pi) remediation from effluent serves to address global water security by preventing eutrophication. Herein, chitosan (C), alginate (Alg) and three respective metal systems (Fe3+, Al3+, Cu2+) were used to prepare binary (BMC) or ternary (TMC) metal composite adsorbents. Their physicochemical properties were analyzed through XPS, IR and TGA, while the adsorption properties of the composites were characterized via adsorption isotherms and single-point experiments in saline environmental water. Al-composites formed Al-O complexes, while Fe- and Cu-composites formed in the presence of the biopolymer backbone FeO(OH) and Cu2(OH)3NO3, respectively. While Al-composites showed the highest bound water fraction (up to 16%), the Cu-composites (Cu-TMC-N, CuC-BMC-N; where N = nitrate) revealed the lowest water content. Alginate-based binary composites showed slightly higher water content, as compared to ternary and binary chitosan composites. Among the four materials (Al-TMC-N, Fe-TMC-N, Cu-TMC-N and CuC-BMC-N), the Al-TMC showed the highest Pi selectivity over sulfate, along with high Pi removal-% even in a binary mixture (sulfate + orthophosphate) despite the presence of competitive anion species. Upon spiking saline groundwater samples with low Pi (5 mg/L) that contains 2060 or 6030 mg/g sulfate, Al-TMC-N showed the highest Pi selectivity, followed by Fe-TMC-N. This trend in adsorption of Pi among the various composites is understood based on the HSAB principle for the conditions employed in this study. Removal efficiencies of Pi above 60% in Well 1 (ca. 2000 mg/L sulfate) and above 30% in Well 3 (ca. 6030 mg/L sulfate). Herein, environmentally compatible and sustainable composite adsorbents were prepared that reveal selective Pi recovery from (highly) saline groundwater that can mitigate eutrophication in aqueous media.
Collapse
|
63
|
Du L, Wang S, Zhu P, Jiang Z. Eco-friendly phosphorus-free flame-retardant coating for microfiber synthetic leather via alginate-based layer-by-layer technology. Int J Biol Macromol 2024; 258:129007. [PMID: 38151082 DOI: 10.1016/j.ijbiomac.2023.129007] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/19/2023] [Revised: 12/20/2023] [Accepted: 12/22/2023] [Indexed: 12/29/2023]
Abstract
The excellent comprehensive properties of microfiber synthetic leathers have led to their wide application in various aspects of our lives. However, the issue of flammability remains a significant challenge that needs to be addressed. Nowadays, the bio-based chemicals used in the flame-retardant materials have extremely grabbed our eyes. Herein, we developed an ecologically friendly flame-retardant microfiber synthetic leather using phosphorus-free layer-by-layer assembly technology (LBL) based on natural polysaccharide alginate (SA) coupled with polyethyleneimine (PEI) and 3-aminopropyltriethoxysilane (APTES). The effect of different LBL coating systems on the flame retardancy of microfiber synthetic leather was investigated. The results demonstrated that the introduction of APTES can completely inhibit the melt-dripping by enhancing char formation through silica elements. Furthermore, the trinary coating system consisting of SA/APTES/PEI exhibited excellent flame retardancy by combining gas-phase action from PEI and condensed-phase function from APTES. This modified microfiber synthetic leather showed a significantly higher limiting oxygen index (LOI) value of 33.0 % with no molten droplet. Additionally, the SA-based coating slightly suppressed the heat release, resulting in a 20 % reduction in total heat release during the combustion test. Overall, this work presents a facile and environmentally-friendly approach for achieving flame-retardant and anti-dripping microfiber synthetic leather.
Collapse
|
64
|
Lotfalinezhad E, Taheri A, Razavi SE, Sanei SJ. Preparation and assessment of alginate-microencapsulated Trichoderma harzianum for controlling Sclerotinia sclerotiorum and Rhizoctonia solani on tomato. Int J Biol Macromol 2024; 259:129278. [PMID: 38211905 DOI: 10.1016/j.ijbiomac.2024.129278] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/27/2023] [Revised: 12/09/2023] [Accepted: 01/04/2024] [Indexed: 01/13/2024]
Abstract
This study aimed to develop microencapsulation technology using alginate to improve the viability and performance of Trichoderma harzianum. The method of ionic gelation was used to prepare the microparticles, and the efficiency of encapsulation was estimated to be 99%. The average size of the prepared microspheres was 2600 μm (wet) and 1000 μm (dry). Scanning electron microscopy revealed that the microspheres were approximately spherical. Fourier transform infrared spectrophotometer analysis indicated an interaction between T. harzianum and the microspheres. The results of temperature resistance and light stability against ultraviolet radiation emphasized the positive impact of microencapsulation in improving the viability and resistance of T. harzianum compared to the non-microencapsulated state. The disease percentage of Rhizoctonia solani and Sclerotinia sclerotiorum in plants treated with microencapsulated T. harzianum microcapsules was 8.88 % and 20 % respectively, but in the control group was 73.33 % (p ≤ 0.05).
Collapse
|
65
|
Singh N, Anand SK, Sharma A, Singh S, Kakkar P, Srivastava V. Chitosan/ alginate nanogel potentiate berberine uptake and enhance oxidative stress mediated apoptotic cell death in HepG2 cells. Int J Biol Macromol 2024; 257:128717. [PMID: 38081485 DOI: 10.1016/j.ijbiomac.2023.128717] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/10/2023] [Revised: 11/21/2023] [Accepted: 12/08/2023] [Indexed: 12/18/2023]
Abstract
Biopolymer-based nanoscale drug delivery systems have become a promising approach to overcome the limitations associated with conventional chemotherapeutics used for cancer treatment. Herein, we reported to develop a hydrophilic nanogel (NG) composed of Chitosan (Chi) and sodium alginate (Alg) using the ion gelation method for delivering Berberine hydrochloride (BBR), an alkaloid obtained from Berberis aristata roots. The use of different nanocarriers for BBR delivery has been reported previously, but the bioavailability of these carriers was limited due to phagocytic uptake and poor systemic delivery. The developed NG showed enhanced stability and efficient entrapment of BBR ∼92 %, resulting in a significant increase in bioavailability. The pH-dependent release behavior demonstrated sustained and effective release of ∼86 %, ∼74 % and, ∼53 % BBR at pH 5.5, 6.6, and 7.4 respectively after 72h, indicating its potential as a drug carrier. Additionally, the cellular uptake of BBR was significantly higher ∼19 % in the BBR-NG (25 μM) than in bulk BBR (100 μM), leading to enhanced ROS generation, mitochondrial depolarisation, and inhibition of cell proliferation and colony formation in HepG2 cells. In summary, the results suggest that the Chi/Alg biopolymer-based nano-formulation could be an effective approach for delivering BBR and enhancing its cellular uptake, efficacy, and cytotoxicity.
Collapse
|
66
|
Kaviani S, Talebi A, Labbaf S, Karimzadeh F. Conductive GelMA/ alginate/polypyrrole/graphene hydrogel as a potential scaffold for cardiac tissue engineering; Physiochemical, mechanical, and biological evaluations. Int J Biol Macromol 2024; 259:129276. [PMID: 38211921 DOI: 10.1016/j.ijbiomac.2024.129276] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/13/2023] [Revised: 12/28/2023] [Accepted: 01/04/2024] [Indexed: 01/13/2024]
Abstract
Cardiac failure can be a life-threatening condition that, if left untreated, can have significant consequences. Functional hydrogel has emerged as a promising platform for cardiac tissue engineering. In the proposed study, gelatin methacrylate (GelMA) and alginate, as a primary matrix to maintain cell viability and proliferation, and polypyrrole and carboxyl-graphene, to improve mechanical and electrical properties, are thoroughly evaluated. Initially, a polymer blend of GelMA/Alginate (1:1) was prepared, and then the addition of 2-5 wt% of polypyrrole was evaluated. Next, the effect of incorporating graphene-carboxyl nanosheets (1, 2, and 3 wt%) within the optimized scaffold with 2 wt% polypyrrole was thoroughly studied. The electrical conductivity of the hydrogels was significantly enhanced from 0.0615 ± 0.007 S/cm in GelMA/alginate to 0.124 ± 0.04 S/cm with the addition of 5 wt% polypyrrole. Also, 3 wt% carboxyl graphene improved the electrical conductivity to 0.27 ± 0.09 S/cm. The compressive strength of carboxyl-graphene-containing hydrogel was in the range of 175 to 520 kPa, and tensile strength was 61 and 133 kPa. The simplicity and low-cost fabrication, tunable mechanical properties, optimal electrical conductivity, blood compatibility, and non-cytotoxicity of GelMA/alginate/polypyrrole/graphene biocomposite hydrogel is a promising construct for cardiac tissue engineering.
Collapse
|
67
|
Fernando PUAI, Kennedy AJ, Pokrzywinski K, Jernberg J, Thornell T, George G, Kosgei GK, Wang Y, Coyne KJ. Development of alginate beads for precise environmental release applications: A design of experiment based approach and analysis. JOURNAL OF ENVIRONMENTAL MANAGEMENT 2024; 351:119872. [PMID: 38157579 DOI: 10.1016/j.jenvman.2023.119872] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/04/2023] [Revised: 12/11/2023] [Accepted: 12/13/2023] [Indexed: 01/03/2024]
Abstract
Controlled release of active ingredients are important for drug delivery and more recently environmental applications including modulated dosing of chemical and biological controls. This study demonstrates the importance of investigating various material science factors that can influence the diffusion rates of alginate beads to improve and tune their performance for marine environmental applications. This investigation aimed to design a rational workflow to aid in leveraging alginate bead use as a carrier matrix for releasing a specific active agent into water. Experiments were conducted to focus on the narrow a large list of relevant material formulation parameters, which included chitosan molecular weight, chitosan concentration, calcium concentration, drop height, and bead size. Once the most relevant material preparation methods were screened, a more robust statistic Design of Experiments approach was performed and results determined the important (and unimportant) factors for increasing dye release kinetics in marine water. The process was further streamlined by narrowing the critical experimental factors to a three-level based on the prior analysis: chitosan MW, chitosan concentration, and bead size. Analysis of the collected data indicated that while chitosan MW had a negligible impact (Fstatistic = 0.22), bead size (Fstatistic = 60.33) significantly influenced the diffusion rates based on surface area. However, chitosan MW had minor effects where lower chitosan MW enabled higher product release rates. This case investigation was a novel application of the design of experiment approach towards environmental applications to understand differences in release rates to marine waters for the first time and the workflow provided also serve as the basis for researchers to optimize other environmental applications requiring optimization when it is unknown how a large number of formulation variables will impact performance in different environmental scenarios.
Collapse
|
68
|
Pang H, Wu Y, Chen Y, Chen C, Nie X, Li P, Huang G, Xu ZP, Han FY. Development of polysaccharide-coated layered double hydroxide nanocomposites for enhanced oral insulin delivery. Drug Deliv Transl Res 2024:10.1007/s13346-023-01504-7. [PMID: 38214820 DOI: 10.1007/s13346-023-01504-7] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Accepted: 12/16/2023] [Indexed: 01/13/2024]
Abstract
Oral insulin (INS) is predicted to have the most therapeutic advantages in treating diabetes to repress hepatic glucose production through its potential to mimic the endogenous insulin pathway. Many oral insulin delivery systems have been investigated. Layered double hydroxide (LDH) as an inorganic material has been widely used in drug delivery thanks to its appealing features such as good biocompatibility, low toxicity, and excellent loading capability. However, when used in oral drug delivery, the effectiveness of LDH is limited due to the acidic degradation in the stomach. In this study, to overcome these challenges, chitosan (Chi) and alginate (Alg) dual-coated LDH nanocomposites with the loading of insulin (Alg-Chi-LDH@INS) were developed by the layered-by-layered method for oral insulin delivery with dynamic size of ~ 350.8 nm, negative charge of ~ - 13.0 mV, and dispersity index 0.228. The insulin release profile was evaluated by ultraviolet-visible spectroscopy. The drug release profiles evidenced that alginate and chitosan coating partially protect insulin release from a burst release in acidic conditions. The analysis using flow cytometry showed that chitosan coating significantly enhanced the uptake of LDH@INS by Caco-2 cells compared to unmodified LDH and free insulin. Further in the in vivo study in streptozocin-induced diabetic mice, a significant hypoglycemic effect was maintained following oral administration with great biocompatibility (~ 50% blood glucose level reduction at 4 h). This research has thus provided a potential nanocomposite system for oral delivery of insulin.
Collapse
|
69
|
Munoz-Perez E, Rubio-Retama J, Cussó L, Igartua M, Hernandez RM, Santos-Vizcaino E. 3D-printed Laponite/ Alginate hydrogel-based suppositories for versatile drug loading and release. Drug Deliv Transl Res 2024:10.1007/s13346-023-01506-5. [PMID: 38185776 DOI: 10.1007/s13346-023-01506-5] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Accepted: 12/18/2023] [Indexed: 01/09/2024]
Abstract
Traditional approaches to solid rectal therapies have halted progress, leading to a continual decline in the use of conventional suppositories. Additive manufacturing techniques have been recently explored as a suitable innovative tool for suppository fabrication. However, little advancement has been made in composition materials for 3D-printed suppository (3DPS) manufacturing and still, conventional vehicles are often used for construct fabrication, hindering the growth in the field. As a novelty, this study unveils a ground-breaking Laponite-alginate hydrogel-based 3DPS. Interestingly, this study proposes a novel approach for loading drugs into the 3DPS employing for the first time the post-printing loading. Thus, a passive loading strategy of molecular models is developed, demonstrating the versatility and capacity to load molecules of different charges and molecular sizes within the matrix systems. This novel strategy allows adapting the load of a wide range of drugs into a single ink, which simplifies and speeds up the 3DPS technological development process for drugs with different physico-chemical properties. Additionally, in this research, a displacement strategy of the three-dimensional Laponite matrices is developed in order to enhance the drug release capacity through the 3DPS and their disintegration capacity, resulting in a significant improvement of the drug diffusion through the hydrogel matrix and a rapid disintegration of the 3DPS. Finally, our study demonstrates that the obtained 3DPS have a suitable in vivo behavior, being non-obstructive and allowing the normal motility of the rats intestine.
Collapse
|
70
|
Kermanian K, Farahpour MR, Tabatabaei ZG. Accelerative effects of alginate-chitosan/titanium oxide@geraniol nanosphere hydrogels on the healing process of wounds infected with Acinetobacter baumannii and Streptococcus pyogenes bacteria. Int J Biol Macromol 2024; 254:127549. [PMID: 37863134 DOI: 10.1016/j.ijbiomac.2023.127549] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/28/2023] [Revised: 10/01/2023] [Accepted: 10/17/2023] [Indexed: 10/22/2023]
Abstract
This study was conducted to evaluate the effects of alginate-chitosan/titanium oxide/geraniol (Alg-Csn/TiO2@GRL nanosphere) nanospheres hydrogels on the healing process of the wounds infected with Acinetobacter baumannii and Streptococcus pyogenes bacteria. The nanospheres were successfully synthesized and their physicochemical properties such as DLS, FTIR, FE-SEM, TEM, XRD and also their safety and in-vitro antibacterial activity were assessed and confirmed. Following induction of the infected wounds, the mice were treated with s base ointment (Control), mupirocin® as standard control group and also hydrogels prepared from Alg-Csn@GRL, Alg-Csn/TiO2 and Alg-Csn/TiO2@GRL. Wound contraction, total bacterial count, expression of bFGF, VEGF, IGF-1, CD68 and COL-1 A, iNOS and eNOS were measured. The results showed the treatment of wounds with Alg-Csn/TiO2@GRL hydrogels significantly accelerated wound contraction, decreased total bacterial count and reduced the expressions of CD68, iNOS and eNOS and increased the expressions of VEGF, bFGF, IGF-1 and COL-1 A compared with other groups. It can be concluded that Alg-Csn/TiO2@GRL hydrogels expedite the wound healing process by their effects on bacteria and subsequently inflammation and increasing the expression of proliferative genes. The Alg-Csn/TiO2@GRL hydrogel can be utilized in combination with other agents for the treatment of infected wounds after future clinical studies.
Collapse
|
71
|
Abd-Elhamid AI, Abu Elgoud EM, Aly HF. Synthesis of Prussian blue-embedded magnetic micro hydrogel for scavenging of cesium from aqueous solutions; Batch and dynamic investigations. Int J Biol Macromol 2024; 254:126864. [PMID: 37703986 DOI: 10.1016/j.ijbiomac.2023.126864] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/27/2023] [Revised: 08/29/2023] [Accepted: 09/09/2023] [Indexed: 09/15/2023]
Abstract
A magnetic micro porous structure composite based on alginate and Prussian blue (M-SA-PB) was simply prepared for cesium removal from the aqueous solutions. The gelation and formation of PB proceeded through the same step, which made the PB homogenously distributed and firmly attached to the alginate matrix. The homogenizer was applied to break down the bulky gel structure into micro-ones, and the lyophilizer will provide the porous structure. Batch cesium sorption experiments showed that the adsorption kinetics and isotherms were attributed to the pseudo-second-order model and Langmuir isotherm. Moreover, the Cs-ion is favorably adsorbed on the M-SA-PB composite surface as a monolayer towards Cs, with a maximum adsorption capacity reach of 191.0 mg/g. Furthermore, the M-SA-PB adsorbent showed excellent adsorption selectivity of Cs from multiple-ion solutions. Our work was extended to use the M-SA-PB composite in dynamic cesium sorption. The column studies showed that the removal efficiency of Cs+ increased with increasing bed depth as well as the initial cesium concentration. Finally, as previously mentioned, the M-SA-PB could be considered an excellent Cs+ scavenger employing both batch and dynamic approaches, which makes it a promising adsorbent for practical investigations.
Collapse
|
72
|
Aycan D, Gül İ, Yorulmaz V, Alemdar N. Gelatin microsphere- alginate hydrogel combined system for sustained and gastric targeted delivery of 5-fluorouracil. Int J Biol Macromol 2024; 255:128022. [PMID: 37972837 DOI: 10.1016/j.ijbiomac.2023.128022] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/27/2023] [Revised: 11/03/2023] [Accepted: 11/09/2023] [Indexed: 11/19/2023]
Abstract
In the current study, novel gelatin microspheres/methacrylated alginate hydrogel combined system (5-FU-GELms/Alg-MA) was developed for gastric targeted delivery of 5-fluorouracil as an anticancer agent. While water-in-oil emulsification method was used for the production of 5-FU-GELms, Alg-MA was synthesized through methacrylation reaction occurred by epoxide ring-opening mechanism. Then, 5-FU-GELms/Alg-MA hydrogel system was fabricated by the encapsulation of 5-FU-GELms into Alg-MA hydrogel network via UV-crosslinking. To evaluate applicability of fabricated 5-FU-GELms/Alg-MA as gastric targeted drug delivery vehicle, both swelling and in vitro drug release experiments were carried out at pH 1.2 medium resembling gastric fluid. Compared to drug release directly from 5-FU-GELms, 5-FU-GELms/Alg-MA hydrogel system showed more controlled and sustained drug release profile with lower amount of cumulative release starting from early stages, since hydrogel matrix created a barrier to the diffusion of 5-FU included in microspheres. Drug release kinetic results obtained by applying various kinetic models to release data showed that the mechanism of 5-FU release from 5-FU-GELms/Alg-MA hydrogel system is controlled by Fickian diffusion. All results revealed that 5-FU-GELms/Alg-MA hydrogel integrated system could be potentially utilized as gastric targeted drug carrier to enhance therapeutic efficacy and reduce systemic side effects in gastric cancer treatments for future studies.
Collapse
|
73
|
Yao Q, Guo J, Guan F, Yang Q, Li J, Bao D, He J, Ji X, Song X. In-situ growth of zinc sulfide on the surface of alginate-based biomass carbon: A new material for removing methylene blue/basic fuchsin and copper ions. Int J Biol Macromol 2024; 256:128360. [PMID: 38000601 DOI: 10.1016/j.ijbiomac.2023.128360] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/30/2023] [Revised: 11/16/2023] [Accepted: 11/20/2023] [Indexed: 11/26/2023]
Abstract
This work aims to prepare a composite adsorbent with a fixed shape to improve the performance of carbon materials and to solve the problem of adsorbent in powder form which is difficult to recycle after use. The BC-ZnS composite system was successfully prepared by hydrothermal method based on the preparation of biomass carbon (BC) using alginate (Alg), while the ZnS component was grown in-situ on the surface of BC. The effects of Alg, Zn source, hydrothermal temperature and time on the synthesis of BC-ZnS were explored, the results indicated that ZnS was successfully grown in-situ on the BC surface, while the BC maintained its original morphology. BC-ZnS showed excellent adsorption capacity for methylene blue (MB), basic fuchsin (BF), and copper ions (Cu2+), reaching 301.50 mg/g for MB and exhibiting good cyclic stability. The adsorption of MB/BF/Cu2+ by BC-ZnS was characterized by the presence of multiple forces, where the BC component mainly depended on the electrostatic force of Alg residue, while the ZnS involves electrostatic forces, ion exchange and Lewis acid/base soft-soft interactions. The adsorption process conforms to pseudo-first-kinetics and is a spontaneous entropy-increasing process. BC-ZnS can be a candidate for reusable wastewater treatment and has excellent potential for application.
Collapse
|
74
|
Xu PW, Yue XJ, Yuan XF, Zhao B. Hemp seed globulin- alginate nanoparticles for encapsulation of Cannabisin A with enhanced colloidal stability and antioxidant activity. Int J Biol Macromol 2024; 256:128380. [PMID: 38000582 DOI: 10.1016/j.ijbiomac.2023.128380] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/25/2023] [Revised: 10/20/2023] [Accepted: 11/21/2023] [Indexed: 11/26/2023]
Abstract
This study develops hemp seed globulin (GLB)-alginate (ALG) nanoparticles (GANPs) for Cannabisin A (CA) stabilization under environmental stress and during pepsin digestion. The optimal GLB: ALG mass ratio of 1: 1.5 was determined for GANPs formation at pH 3.5, resulting in a high yield of 95.13 ± 0.91 %, a ζ-potential of -35.73 ± 1.04 mV, a hydrodynamic diameter of 470.67 ± 11.36 nm, and a PDI of 0.298 ± 0.016. GANPs were employed to encapsulate CA, achieving a high loading capacity of 13.48 ± 0.04 μg mg-1. FTIR analysis demonstrated that the formation of CA-GLB-ALG nanoparticles (CGANPs) involves electrostatic interactions, hydrogen bonding, and hydrophobic interactions. XRD and DSC analyses revealed that CA is amorphous within the CGANPs. CGANPs demonstrated remarkable dispersion stability as well as resistance to high ionic strength and high-temperature treatments, indicating their potential as efficient hydrophobic drug-delivery vehicles. When compared to free CA, CA coated within CGANPs displayed greater DPPH/ABTS scavenging activity. Furthermore, the ALG-shelled nanoparticles protected GLB from pepsin digestion and slowed the release of CA throughout the release process, extending their stay on the intestinal wall mucosa. These findings imply that CGANPs is an ideal delivery vehicle for CA as they may expand the application of CA in food items.
Collapse
|
75
|
Xiao Z, Li K, Li T, Zhang F, Xue J, Zhao M, Yin H. Characterization and Mechanism Study of a Novel PL7 Family Exolytic Alginate Lyase from Marine Bacteria Vibrio sp. W13. Appl Biochem Biotechnol 2024; 196:68-84. [PMID: 37099125 DOI: 10.1007/s12010-023-04483-0] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Accepted: 04/11/2023] [Indexed: 04/27/2023]
Abstract
Alginate lyase can degrade alginate into oligosaccharides through β-elimination for various biological, biorefinery, and agricultural purposes. Here, we report a novel PL7 family exolytic alginate lyase VwAlg7A from marine bacteria Vibrio sp. W13 and achieve the heterologous expression in E. coli BL21 (DE3). VwAlg7A is 348aa with a calculated molecular weight of 36 kDa, containing an alginate lyase 2 domain. VwAlg7A exhibits specificity towards poly-guluronate. The optimal temperature and pH of VwAlg7A are 30 °C and 7.0, respectively. The activity of VwAlg7A can be significantly inhibited by the Ni2+, Zn2+, and NaCl. The Km and Vmax of VwAlg7A are 36.9 mg/ml and 395.6 μM/min, respectively. The ESI and HPAEC-PAD results indicate that VwAlg7A cleaves the sugar bond in an exolytic mode. Based on the molecular docking and mutagenesis results, we further confirmed that R98, H169, and Y303 are important catalytic residues.
Collapse
|