151
|
Chahine NO, Chen FH, Hung CT, Ateshian GA. Direct measurement of osmotic pressure of glycosaminoglycan solutions by membrane osmometry at room temperature. Biophys J 2005; 89:1543-50. [PMID: 15980166 PMCID: PMC1366659 DOI: 10.1529/biophysj.104.057315] [Citation(s) in RCA: 81] [Impact Index Per Article: 4.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/18/2022] Open
Abstract
Articular cartilage is a hydrated soft tissue composed of negatively charged proteoglycans fixed within a collagen matrix. This charge gradient causes the tissue to imbibe water and swell, creating a net osmotic pressure that enhances the tissue's ability to bear load. In this study we designed and utilized an apparatus for directly measuring the osmotic pressure of chondroitin sulfate, the primary glycosaminoglycan found in articular cartilage, in solution with varying bathing ionic strength (0.015 M, 0.15 M, 0.5 M, 1 M, and 2 M NaCl) at room temperature. The osmotic pressure (pi) was found to increase nonlinearly with increasing chondroitin sulfate concentration and decreasing NaCl ionic bath environment. Above 1 M NaCl, pi changes negligibly with further increases in salt concentration, suggesting that Donnan osmotic pressure is negligible above this threshold, and the resulting pressure is attributed to configurational entropy. Results of the current study were also used to estimate the contribution of osmotic pressure to the stiffness of cartilage based on theoretical and experimental considerations. Our findings indicate that the osmotic pressure resulting from configurational entropy is much smaller in cartilage (based on an earlier study on bovine articular cartilage) than in free solution. The rate of change of osmotic pressure with compressive strain is found to contribute approximately one-third of the compressive modulus (H(A)(eff)) of cartilage (Pi approximately H(A)(eff)/3), with the balance contributed by the intrinsic structural modulus of the solid matrix (i.e., H(A) approximately 2H(A)(eff)/3). A strong dependence of this intrinsic modulus on salt concentration was found; therefore, it appears that proteoglycans contribute structurally to the magnitude of H(A), in a manner independent of osmotic pressure.
Collapse
|
152
|
Basalo IM, Raj D, Krishnan R, Chen FH, Hung CT, Ateshian GA. Effects of enzymatic degradation on the frictional response of articular cartilage in stress relaxation. J Biomech 2005; 38:1343-9. [PMID: 15863119 PMCID: PMC2833092 DOI: 10.1016/j.jbiomech.2004.05.045] [Citation(s) in RCA: 44] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Accepted: 05/30/2004] [Indexed: 10/26/2022]
Abstract
It was recently shown experimentally that the friction coefficient of articular cartilage correlates with the interstitial fluid pressurization, supporting the hypothesis that interstitial water pressurization plays a fundamental role in the frictional response by supporting most of the load during the early time response. A recent study showed that enzymatic treatment with chondroitinase ABC causes a decrease in the maximum fluid load support of bovine articular cartilage in unconfined compression. The hypothesis of this study is that treatment with chondroitinase ABC will increase the friction coefficient of articular cartilage in stress relaxation. Articular cartilage samples (n = 34) harvested from the femoral condyles of five bovine knee joints (1-3 months old) were tested in unconfined compression with simultaneous continuous sliding (+/-1.5 mm at 1 mm/s) under stress relaxation. Results showed a significantly higher minimum friction coefficient in specimens treated with 0.1 micro/ml of chondroitinase ABC for 24 h (micro(min) = 0.082+/-0.024) compared to control specimens (micro(min) = 0.047+/-0.014). Treated samples also exhibited higher equilibrium friction coefficient (micro(eq) = 0.232+/-0.049) than control samples (micro(eq) = 0.184+/-0.036), which suggest that the frictional response is greatly influenced by the degree of tissue degradation. The fluid load support was predicted from theory, and the maximum value (as a percentage of the total applied load) was lower in treated specimens (77+/-12%) than in control specimens (85+/-6%). Based on earlier findings, the increase in the ratio micro(min)/micro(eq) may be attributed to the decrease in fluid load support.
Collapse
|
153
|
Chahine NO, Wang CCB, Hung CT, Ateshian GA. Anisotropic strain-dependent material properties of bovine articular cartilage in the transitional range from tension to compression. J Biomech 2005; 37:1251-61. [PMID: 15212931 PMCID: PMC2819725 DOI: 10.1016/j.jbiomech.2003.12.008] [Citation(s) in RCA: 127] [Impact Index Per Article: 6.7] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Accepted: 12/01/2003] [Indexed: 11/30/2022]
Abstract
Articular cartilage exhibits complex mechanical properties such as anisotropy, inhomogeneity and tension-compression nonlinearity. This study proposes and demonstrates that the application of compressive loading in the presence of osmotic swelling can be used to acquire a spectrum of incremental cartilage moduli (EYi) and Poisson's ratios (upsilon ij) from tension to compression. Furthermore, the anisotropy of the tissue can be characterized in both tension and compression by conducting these experiments along three mutually perpendicular loading directions: parallel to split-line (1-direction), perpendicular to split-line (2-direction) and along the depth direction (3-direction, perpendicular to articular surface), accounting for tissue inhomogeneity between the surface and deep layers in the latter direction. Tensile moduli were found to be strain-dependent while compressive moduli were nearly constant. The peak tensile (+) Young's moduli in 0.15M NaCl were E+Y1=3.1+/-2.3, E+Y2=1.3+/-0.3, E+Y3(Surface)=0.65+/-0.29 and E+Y3(Deep)=2.1+/-1.2 MPa. The corresponding compressive (-) Young's moduli were E-Y1=0.23+/-0.07, E-Y2=0.22+/-0.07, E-Y3(Surface)=0.18+/-0.07 and E-Y3(Deep)=0.35+/-0.11 MPa. Peak tensile Poisson's ratios were upsilon+12=0.22+/-0.06, upsilon+21=0.13+/-0.07, upsilon+31(Surface)=0.10+/-0.03 and upsilon+31(Deep)=0.20+/-0.05 while compressive Poisson's ratios were upsilon-12=0.027+/-0.012, upsilon-21=0.017+/-0.07, upsilon-31(Surface)=0.034+/-0.009 and upsilon-31(Deep)=0.065+/-0.024. Similar measurements were also performed at 0.015 M and 2 M NaCl, showing strong variations with ionic strength. Results indicate that (a) a smooth transition occurs in the stress-strain and modulus-strain responses between the tensile and compressive regimes, and (b) cartilage exhibits orthotropic symmetry within the framework of tension-compression nonlinearity. The strain-softening behavior of cartilage (the initial decrease in EYi with increasing compressive strain) can be interpreted in the context of osmotic swelling and tension-compression nonlinearity.
Collapse
|
154
|
Ng KW, Wang CCB, Mauck RL, Kelly TAN, Chahine NO, Costa KD, Ateshian GA, Hung CT. A layered agarose approach to fabricate depth-dependent inhomogeneity in chondrocyte-seeded constructs. J Orthop Res 2005; 23:134-41. [PMID: 15607885 DOI: 10.1016/j.orthres.2004.05.015] [Citation(s) in RCA: 122] [Impact Index Per Article: 6.4] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 02/04/2023]
Abstract
Inspired by the depth-dependent inhomogeneity of articular cartilage, it was hypothesized that a novel layered agarose technique, using a 2% (wt/vol) top and a 3% (wt/vol) bottom layer, would create an inhomogenous tissue construct with distinct material properties in conjoined regions. The biochemical and mechanical development of these constructs was observed alongside uniform 2% and 3% constructs. Initially, uniform 3% agarose disks had the highest bulk Young's modulus (E(Y) approximately 28 kPa) of all groups. After 28 days of culture in 20% FBS-containing media, however, uniform 2% chondrocyte-seeded constructs achieved the highest Young's modulus compared to bilayered and 3% agarose disks. Though all three groups contained similar GAG content ( approximately 1.5% ww), uniform 2% agarose disks on day 28 possessed the highest collagen content ( approximately 1% ww). Unlike in either homogeneous construct type, microscopic analysis of axial strain fields in bilayered constructs in response to applied static compression revealed two mechanically disparate regions on day 0: a softer 2% layer and a stiffer 3% layer. With time in culture, this inhomogeneity became less distinct, as indicated by increased continuity in both the local displacement field and local E(Y), and depended on the level of FBS supplementation of the feed media, with lower FBS concentrations (10%) more closely maintaining the original distinction of material properties. These results shed positive light on a layered agarose technique for the production of inhomogeneous bilayered chondrocyte-seeded agarose constructs with applications for investigations of chondrocyte mechanotransduction and for possible use in the tissue engineering of inhomogeneous articular cartilage constructs.
Collapse
|
155
|
Finkelstein E, Chang W, Chao PHG, Gruber D, Minden A, Hung CT, Bulinski JC. Roles of microtubules, cell polarity and adhesion in electric-field-mediated motility of 3T3 fibroblasts. J Cell Sci 2004; 117:1533-45. [PMID: 15020680 DOI: 10.1242/jcs.00986] [Citation(s) in RCA: 62] [Impact Index Per Article: 3.1] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/30/2022] Open
Abstract
Direct-current electric fields mediate motility (galvanotaxis) of many cell types. In 3T3 fibroblasts, electric fields increased the proportion, speed and cathodal directionality of motile cells. Analogous to fibroblasts' spontaneous migration, we initially hypothesized that reorientation of microtubule components modulates galvanotaxis. However, cells with intact microtubules did not reorient them in the field and cells without microtubules still migrated, albeit slowly, thus disproving the hypothesis. We next proposed that, in monolayers wounded and placed in an electric field, reorientation of microtubule organizing centers and stable, detyrosinated microtubules towards the wound edge is necessary and/or sufficient for migration. This hypothesis was negated because field exposure mediated migration of unoriented, cathode-facing cells and curtailed migration of oriented, anode-facing cells. This led us to propose that ablating microtubule detyrosination would not affect galvanotaxis. Surprisingly, preventing microtubule detyrosination increased motility speed, suggesting that detyrosination inhibits galvanotaxis. Microtubules might enhance adhesion/de-adhesion remodeling during galvanotaxis; thus, electric fields might more effectively mediate motility of cells poorly or dynamically attached to substrata. Consistent with this hypothesis, incompletely spread cells migrated more rapidly than fully spread cells. Also, overexpression of PAK4, a Cdc42-activated kinase that decreases adhesion, enhanced galvanotaxis speed, whereas its lack decreased speed. Thus, electric fields mediate fibroblast migration via participation of microtubules and adhesive components, but their participation differs from that during spontaneous motility.
Collapse
|
156
|
Lam KW, Cheng F, Chan JWM, Cheung GSY, Lee MWM, Hung CT. Ethical attitudes of non-intensive care unit clinicians upon end-of-life issue: more training is necessary. Hong Kong Med J 2004; 10:438. [PMID: 15591608] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [MESH Headings] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 05/01/2023] Open
|
157
|
Krishnan R, Caligaris M, Mauck RL, Hung CT, Costa KD, Ateshian GA. Removal of the superficial zone of bovine articular cartilage does not increase its frictional coefficient. Osteoarthritis Cartilage 2004; 12:947-55. [PMID: 15564061 PMCID: PMC2828954 DOI: 10.1016/j.joca.2004.08.009] [Citation(s) in RCA: 48] [Impact Index Per Article: 2.4] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 11/24/2003] [Accepted: 08/18/2004] [Indexed: 02/02/2023]
Abstract
OBJECTIVE To investigate the role of the superficial zone in regulating the frictional response of articular cartilage. This zone contains the superficial protein (SZP), a proteoglycan synthesized exclusively by superficial zone chondrocytes and implicated in reducing the friction coefficient of cartilage. DESIGN Unconfined compression creep tests with sliding of cartilage against glass in saline were carried out on fresh bovine cylindrical plugs (slashed circle Ø6 mm, n=35) obtained from 16 bovine shoulder joints (ages 1-3 months). In the first two experiments, friction tests were carried out before and after removal of the superficial zone ( approximately 100 microm), in a control and treatment group, using two different applied load magnitudes (4.4 N and 22.2 N). In the third experiment, friction tests were conducted on intact surfaces and the corresponding microtomed deep zone of the same specimen. RESULTS In all tests the friction coefficient exhibited a transient response, increasing from a minimum value (mu(min)) to a near-equilibrium final value (micro(eq)). No statistical change (P>0.5) was found in micro(min) before and after removal of the superficial zone in both experiments 1 and 2. However, micro(eq) was observed to decrease significantly (P<0.001) after removal of the surface zone. Results from the third experiment confirm that micro(eq) is even lower at the deep zone. Surface roughness measurements with atomic force microscopy (AFM) revealed an increase in surface roughness after microtoming. Immunohistochemical staining confirmed the presence of SZP in intact specimens and its removal in microtomed specimens. CONCLUSIONS The topmost ( approximately 100 microm) superficial zone of articular cartilage does not have special properties which enhances its frictional response.
Collapse
|
158
|
Chao PG, Tang Z, Angelini E, West AC, Costa KD, Hung CT. Dynamic osmotic loading of chondrocytes using a novel microfluidic device. J Biomech 2004; 38:1273-81. [PMID: 15863112 DOI: 10.1016/j.jbiomech.2004.06.016] [Citation(s) in RCA: 26] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/08/2003] [Revised: 06/14/2004] [Accepted: 06/21/2004] [Indexed: 10/26/2022]
Abstract
Many cells exhibit disparate responses to a mechanical stimulus depending on whether it is applied dynamically or statically. In this context, few studies have examined how cells respond to dynamic changes of the extracellular osmolality. In this study, we hypothesized that the cell size change response of cultured articular chondrocytes would be dependent on the frequency of applied osmotic loading. To test this hypothesis, we developed a novel microfluidic device, to apply hydrostatic pressure-driven dynamic osmotic loading by applying composition modulated flow, adapted from Tang and co-workers. This microfluidic device was used to study osmotic loads of +/-180 mOsm at a frequency up to 0.1 Hz with a constant minimal fluid-shear stress, and permit real-time monitoring of cell responses. Bovine articular chondrocytes were observed to exhibit increasing changes in cell volume with decreasing osmotic loading frequency. When the cell volume response was modeled by an exponential function, chondrocytes exhibited significantly different volume change responses to dynamic osmotic loading at 0.0125 Hz and static osmotic loading applied for a period of four minutes (Delta = +/-180 mOsm relative to the isotonic 360 mOsm). The intracellular calcium response at 0.0125 Hz was also monitored and compared with the response to static loading. Coupled with phenomenological or constitutive models, this novel approach could yield new information regarding cell material properties in response to dynamic loading that may contribute new insights into mechanisms of cellular homeostasis and mechanotransduction.
Collapse
|
159
|
Takai E, Mauck RL, Hung CT, Guo XE. Osteocyte viability and regulation of osteoblast function in a 3D trabecular bone explant under dynamic hydrostatic pressure. J Bone Miner Res 2004; 19:1403-10. [PMID: 15312240 DOI: 10.1359/jbmr.040516] [Citation(s) in RCA: 65] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 02/06/2004] [Revised: 04/02/2004] [Accepted: 05/05/2004] [Indexed: 11/18/2022]
Abstract
UNLABELLED A new trabecular bone explant model was used to examine osteocyte-osteoblast interactions under DHP loading. DHP loading enhanced osteocyte viability as well as osteoblast function measured by osteoid formation. However, live osteocytes were necessary for osteoblasts to form osteoids in response to DHP, which directly show osteoblast-osteocyte interactions in this in vitro culture. INTRODUCTION A trabecular bone explant model was characterized and used to examine the effect of osteocyte and osteoblast interactions and dynamic hydrostatic pressure (DHP) loading on osteocyte viability and osteoblast function in long-term culture. MATERIALS AND METHODS Trabecular bone cores obtained from metacarpals of calves were cleaned of bone marrow and trabecular surface cells and divided into six groups, (1) live cores + dynamic hydrostatic pressure (DHP), (2) live cores + sham, (3) live cores + osteoblast + DHP, (4) live cores + osteoblast + sham, (5) devitalized cores + osteoblast + DHP, and (6) devitalized cores + osteoblast + sham, with four culture durations (2, 8, 15, and 22 days; n = 4/group). Cores from groups 3-6 were seeded with osteoblasts, and cores from groups 5 and 6 were devitalized before seeding. Groups 1, 3, and 5 were subjected to daily DHP loading. Bone histomorphometry was performed to quantify osteocyte viability based on morphology and to assess osteoblast function based on osteoid surface per bone surface (Os/Bs). TUNEL staining was performed to evaluate the mode of osteocyte death under various conditions. RESULTS A portion of osteocytes remained viable for the duration of culture. DHP loading significantly enhanced osteocyte viability up to day 8, whereas the presence of seeded osteoblasts significantly decreased osteocyte viability. Cores with live osteocytes showed higher Os/Bs compared with devitalized cores, which reached significant levels over a greater range of time-points when combined with DHP loading. DHP loading did not increase Os/Bs in the absence of live osteocytes. The percentage of apoptotic cells remained the same regardless of treatment or culture duration. CONCLUSION Enhanced osteocyte viability with DHP suggests the necessity of mechanical stimulation for osteocyte survival in vitro. Furthermore, osteocytes play a critical role in the transmission of signals from DHP loading to modulate osteoblast function. This explant culture model may be used for mechanotransduction studies in long-term cultures.
Collapse
|
160
|
Ateshian GA, Chahine NO, Basalo IM, Hung CT. The correspondence between equilibrium biphasic and triphasic material properties in mixture models of articular cartilage. J Biomech 2004; 37:391-400. [PMID: 14757459 PMCID: PMC2819758 DOI: 10.1016/s0021-9290(03)00252-5] [Citation(s) in RCA: 66] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/18/2022]
Abstract
Mixture models have been successfully used to describe the response of articular cartilage to various loading conditions. Mow et al. (J. Biomech. Eng. 102 (1980) 73) formulated a biphasic mixture model of articular cartilage where the collagen-proteoglycan matrix is modeled as an intrinsically incompressible porous-permeable solid matrix, and the interstitial fluid is modeled as an incompressible fluid. Lai et al. (J. Biomech. Eng. 113 (1991) 245) proposed a triphasic model of articular cartilage as an extension of their biphasic theory, where negatively charged proteoglycans are modeled to be fixed to the solid matrix, and monovalent ions in the interstitial fluid are modeled as additional fluid phases. Since both models co-exist in the cartilage literature, it is useful to show how the measured properties of articular cartilage (the confined and unconfined compressive and tensile moduli, the compressive and tensile Poisson's ratios, and the shear modulus) relate to both theories. In this study, closed-form expressions are presented that relate biphasic and triphasic material properties in tension, compression and shear. These expressions are then compared to experimental findings in the literature to provide greater insight into the measured properties of articular cartilage as a function of bathing solutions salt concentrations and proteoglycan fixed-charge density.
Collapse
|
161
|
Hung CT, Mauck RL, Wang CCB, Lima EG, Ateshian GA. A paradigm for functional tissue engineering of articular cartilage via applied physiologic deformational loading. Ann Biomed Eng 2004; 32:35-49. [PMID: 14964720 DOI: 10.1023/b:abme.0000007789.99565.42] [Citation(s) in RCA: 168] [Impact Index Per Article: 8.4] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/12/2022]
Abstract
Deformational loading represents a primary component of the chondrocyte physical environment in vivo. This review summarizes our experience with physiologic deformational loading of chondrocyte-seeded agarose hydrogels to promote development of cartilage constructs having mechanical properties matching that of the parent calf tissue, which has a Young's modulus E(Y) = 277 kPa and unconfined dynamic modulus at 1 Hz G* = 7 MPa. Over an 8-week culture period, cartilage-like properties have been achieved for 60 x 10(6) cells/ml seeding density agarose constructs, with E(Y) = 186 kPa, G* = 1.64 MPa. For these constructs, the GAG content reached 1.74% ww and collagen content 2.64% ww compared to 2.4% ww and 21.5% ww for the parent tissue, respectively. Issues regarding the deformational loading protocol, cell-seeding density, nutrient supply, growth factor addition, and construct mechanical characterization are discussed. In anticipation of cartilage repair studies, we also describe early efforts to engineer cylindrical and anatomically shaped bilayered constructs of agarose hydrogel and bone (i.e., osteochondral constructs). The presence of a bony substrate may facilitate integration upon implantation. These efforts will provide an underlying framework from which a functional tissue-engineering approach, as described by Butler and coworkers (2000), may be applied to general cell-scaffold systems adopted for cartilage tissue engineering.
Collapse
|
162
|
Mauck RL, Hung CT, Ateshian GA. Modeling of neutral solute transport in a dynamically loaded porous permeable gel: implications for articular cartilage biosynthesis and tissue engineering. J Biomech Eng 2004; 125:602-14. [PMID: 14618919 PMCID: PMC2854001 DOI: 10.1115/1.1611512] [Citation(s) in RCA: 164] [Impact Index Per Article: 8.2] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/08/2022]
Abstract
A primary mechanism of solute transport in articular cartilage is believed to occur through passive diffusion across the articular surface, but cyclical loading has been shown experimentally to enhance the transport of large solutes. The objective of this study is to examine the effect of dynamic loading within a theoretical context, and to investigate the circumstances under which convective transport induced by dynamic loading might supplement diffusive transport. The theory of incompressible mixtures was used to model the tissue (gel) as a mixture of a gel solid matrix (extracellular matrix/scaffold), and two fluid phases (interstitial fluid solvent and neutral solute), to solve the problem of solute transport through the lateral surface of a cylindrical sample loaded dynamically in unconfined compression with frictionless impermeable platens in a bathing solution containing an excess of solute. The resulting equations are governed by nondimensional parameters, the most significant of which are the ratio of the diffusive velocity of the interstitial fluid in the gel to the solute diffusivity in the gel (Rg), the ratio of actual to ideal solute diffusive velocities inside the gel (Rd), the ratio of loading frequency to the characteristic frequency of the gel (f), and the compressive strain amplitude (epsilon 0). Results show that when Rg > 1, Rd < 1, and f > 1, dynamic loading can significantly enhance solute transport into the gel, and that this effect is enhanced as epsilon 0 increases. Based on representative material properties of cartilage and agarose gels, and diffusivities of various solutes in these gels, it is found that the ranges Rg > 1, Rd < 1, correspond to large solutes, whereas f > 1 is in the range of physiological loading frequencies. These theoretical predictions are thus in agreement with the limited experimental data available in the literature. The results of this study apply to any porous hydrated tissue or material, and it is therefore plausible to hypothesize that dynamic loading may serve to enhance solute transport in a variety of physiological processes.
Collapse
|
163
|
Park S, Hung CT, Ateshian GA. Mechanical response of bovine articular cartilage under dynamic unconfined compression loading at physiological stress levels. Osteoarthritis Cartilage 2004; 12:65-73. [PMID: 14697684 DOI: 10.1016/j.joca.2003.08.005] [Citation(s) in RCA: 211] [Impact Index Per Article: 10.6] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 02/02/2023]
Abstract
OBJECTIVE The objective of this study was to characterize the dynamic modulus and compressive strain magnitudes of bovine articular cartilage at physiological compressive stress levels and loading frequencies. DESIGN Twelve distal femoral cartilage plugs (3mm in diameter) were loaded in a custom apparatus under load control, with a load amplitude up to 40 N and loading frequencies of 0.1, 1, 10 and 40 Hz, resulting in peak Cauchy stress amplitudes of 4.8 MPa (engineering stress 5.7 MPa). RESULTS The equilibrium Young's modulus under a tare load of 0.4N was 0.49+/-0.10 MPa. In the limit of zero applied stress, the incremental dynamic modulus derived from the slope of the stress-strain curve increased from 14.6+/-6.9 MPa at 0.1 Hz to 28.7+/-7.8 MPa at 40 Hz. At 4 MPa of applied stress, the corresponding increase was from 48.2+/-13.5 MPa at 0.1 Hz to 64.8+/-13.0 MPa at 40 Hz. Peak compressive strain amplitudes varied from 15.8+/-3.4% at 0.1 Hz to 8.7+/-1.8% at 40 Hz. The phase angle decreased from 28.8 degrees +/-6.7 degrees at 0.1 Hz to-0.5 degrees +/-3.8 degrees at 40 Hz. DISCUSSION These results are representative of the functional properties of articular cartilage under physiological load magnitudes and frequencies. The viscoelasticity and nonlinearity of the tissue helps to maintain the compressive strains below 20% under the physiological compressive stresses achieved in this study. These findings have implications for our understanding of cartilage metabolism and chondrocyte viability under various loading regimes. They also help establish guidelines for cartilage functional tissue engineering studies.
Collapse
|
164
|
Kelly TAN, Wang CCB, Mauck RL, Ateshian GA, Hung CT. Role of cell-associated matrix in the development of free-swelling and dynamically loaded chondrocyte-seeded agarose gels. Biorheology 2004; 41:223-37. [PMID: 15299255] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 04/30/2023]
Abstract
Chondrocytes embedded in agarose and subjected to dynamic deformational loading produce a functional matrix with time in culture, but there is usually a delay in the development of significant differences compared to free swelling. In this study, we hypothesized that the initial presence of a cell-associated matrix would expedite construct development in response to dynamic deformational loading. Seeded samples with enzymatically isolated chondrocytes and chondrons (the chondrocyte and its pericellular matrix) and examined the effects of seeding density and dynamic loading on the development of tissue properties. At 60 million/ml, dynamic loading significantly augmented the development of material properties in chondrocyte- and chondron-seeded constructs. Biochemical content and histological analysis indicated that the deposition of GAG, link protein and collagens are affected by the pre-existing cell-associated matrix of the chondron-seeded samples. The pericellular matrix associated with the chondrons did not expedite the development of material properties in response to deformational loading, disproving our hypothesis. The relative concentration and distribution of matrix proteins may play a major role in the disparate responses observed for the chondrocyte- and chondron-seeded cultures. In further support of these findings, culturing chondrocytes in agarose for two weeks prior to the application of deformational loading also did not exhibit expedited construct development.
Collapse
|
165
|
Lima EG, Mauck RL, Han SH, Park S, Ng KW, Ateshian GA, Hung CT. Functional tissue engineering of chondral and osteochondral constructs. Biorheology 2004; 41:577-90. [PMID: 15299288] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 04/30/2023]
Abstract
Due to the prevalence of osteoarthritis (OA) and damage to articular cartilage, coupled with the poor intrinsic healing capacity of this avascular connective tissue, there is a great demand for an articular cartilage substitute. As the bearing material of diarthrodial joints, articular cartilage has remarkable functional properties that have been difficult to reproduce in tissue-engineered constructs. We have previously demonstrated that by using a functional tissue engineering approach that incorporates mechanical loading into the long-term culture environment, one can enhance the development of mechanical properties in chondrocyte-seeded agarose constructs. As these gel constructs begin to achieve material properties similar to that of the native tissue, however, new challenges arise, including integration of the construct with the underlying native bone. To address this issue, we have developed a technique for producing gel constructs integrated into an underlying bony substrate. These osteochondral constructs develop cartilage-like extracellular matrix and material properties over time in free swelling culture. In this study, as a preliminary to loading such osteochondral constructs, finite element modeling (FEM) was used to predict the spatial and temporal stress, strain, and fluid flow fields within constructs subjected to dynamic deformational loading. The results of these models suggest that while chondral ("gel alone") constructs see a largely homogenous field of mechanical signals, osteochondral ("gel bone") constructs see a largely inhomogeneous distribution of mechanical signals. Such inhomogeneity in the mechanical environment may aid in the development of inhomogeneity in the engineered osteochondral constructs. Together with experimental observations, we anticipate that such modeling efforts will provide direction for our efforts aimed at the optimization of applied physical forces for the functional tissue engineering of an osteochondral articular cartilage substitute.
Collapse
|
166
|
Hung CT, Lima EG, Mauck RL, Takai E, Taki E, LeRoux MA, Lu HH, Stark RG, Guo XE, Ateshian GA. Anatomically shaped osteochondral constructs for articular cartilage repair. J Biomech 2003; 36:1853-64. [PMID: 14614939 DOI: 10.1016/s0021-9290(03)00213-6] [Citation(s) in RCA: 166] [Impact Index Per Article: 7.9] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/13/2023]
Abstract
Few successful treatment modalities exist for surface-wide, full-thickness lesions of articular cartilage. Functional tissue engineering offers a great potential for the clinical management of such lesions. Our long-term hypothesis is that anatomically shaped tissue constructs of entire articular layers can be engineered in vitro on a bony substrate, for subsequent implantation. To determine the feasibility, this study investigated the development of bilayered scaffolds of chondrocyte-seeded agarose on natural trabecular bone. In a series of three experiments, bovine chondrocytes were seeded in (1) cylindrical bilayered constructs of agarose and bovine trabecular bone, 0.53 cm2 in surface area and 3.2 mm thick, and were cultured for up to 6 weeks; (2) chondrocyte-seeded anatomically shaped agarose constructs reproducing the human patellar articular layer (area=11.7 cm2, mean thickness=3.4 mm), cultured for up to 6 weeks; and (3) chondrocyte-seeded anatomically shaped agarose constructs of the patella (same as above) integrated into a corresponding anatomically shaped trabecular bone substrate, cultured for up to 2 weeks. Articular layer geometry, previously acquired from human cadaver joints, was used in conjunction with computer-aided design and manufacturing technology to create these anatomically accurate molds. In all experiments, chondrocytes remained viable over the entire culture period, with the agarose maintaining its shape while remaining firmly attached to the underlying bony substrate (when present). With culture time, the constructs exhibited positive type II collagen staining as well as increased matrix elaboration (Safranin O staining for glycosaminoglycans) and material properties (Young's modulus and aggregate modulus). Despite the use of relatively large agarose constructs partially integrated with trabecular bone, no adverse diffusion limitation effects were observed. Anatomically shaped constructs on a bony substrate may represent a new paradigm in the design of a functional articular cartilage tissue replacement.
Collapse
|
167
|
Mauck RL, Wang CCB, Oswald ES, Ateshian GA, Hung CT. The role of cell seeding density and nutrient supply for articular cartilage tissue engineering with deformational loading. Osteoarthritis Cartilage 2003; 11:879-90. [PMID: 14629964 DOI: 10.1016/j.joca.2003.08.006] [Citation(s) in RCA: 213] [Impact Index Per Article: 10.1] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 02/02/2023]
Abstract
OBJECTIVE Functional tissue engineering (FTE) of articular cartilage involves the use of physiologically relevant mechanical signals to encourage the growth of engineered constructs. The goal of this study was to determine the utility of deformational loading in enhancing the mechanical properties of chondrocyte-seeded agarose hydrogels, and to investigate the role of initial cell seeding density and nutrient supply in this process. DESIGN Chondrocyte-seeded agarose hydrogels were cultured in free-swelling conditions or with intermittent deformational loading (10% deformation, 1 Hz, 1 h on/ 1 h off, 3 h per day, five days per week) over a two-month culture period. Disks were seeded at lower (10 million cells/ml) and higher (60 million cells/ml) seeding densities in the context of a greater medium supply than previous studies (decreasing the number of cells/ml feed medium/day) and with an increasing concentration of fetal bovine serum (10 or 20% FBS). RESULTS Under these more optimal nutrient conditions, at higher seeding densities and high serum concentration (20% FBS), dynamically loaded constructs show >2-fold increases in material properties relative to free-swelling controls. After two months of culture, dynamically loaded constructs achieved a Young's modulus of approximately 185 kPa and a dynamic modulus (at 1 Hz) of approximately 1.6 MPa, with a frequency dependent response similar to that of the native tissue. These values represent approximately 3/4 and approximately 1/4 the values measured for the native tissue, respectively. While significant differences were found in mechanical properties, staining and bulk measurements of both proteoglycan and collagen content of higher seeding density constructs revealed no significant differences between free-swelling and loading groups. This finding indicates that deformational loading may act to increase material properties via differences in the structural organization, the production of small linker ECM molecules, or by modulating the size of macromolecular proteoglycan aggregates. CONCLUSIONS Taken together, these results point to the utility of dynamic deformational loading in the mechanical preconditioning of engineered articular cartilage constructs and the necessity for increasing feed media volume and serum supplementation with increasing cell seeding densities.
Collapse
|
168
|
Morrison B, Cater HL, Wang CCB, Thomas FC, Hung CT, Ateshian GA, Sundstrom LE. A tissue level tolerance criterion for living brain developed with an in vitro model of traumatic mechanical loading. STAPP CAR CRASH JOURNAL 2003; 47:93-105. [PMID: 17096246 DOI: 10.4271/2003-22-0006] [Citation(s) in RCA: 10] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/12/2023]
Abstract
Traumatic brain injury (TBI) is caused by brain deformations resulting in the pathophysiological activation of cellular cascades which produce delayed cell damage and death. Understanding the consequences of mechanical injuries on living brain tissue continues to be a significant challenge. We have developed a reproducible tissue culture model of TBI which employs organotypic brain slice cultures to study the relationship between mechanical stimuli and the resultant biological response of living brain tissue. The device allows for the independent control of tissue strain (up to 100%) and strain rate (up to 150 s-1) so that tolerance criteria at the tissue level can be developed for the interpretation of computational simulations. The application of texture correlation image analysis algorithms to high speed video of the dynamic deformation allows for the direct calculation of substrate strain and strain rate which was found to be equi-biaxial and independent of radial position. Precisely controlled, mechanical injuries were applied to organotypic hippocampal slice cultures, and resultant cell death was quantified. Cell death was found to be dependent on both strain magnitude and rate and required several days to develop. An immunohistological examination of injured cultures with antibodies to amyloid precursor protein revealed the presence of traumatic axonal injury, suggesting that the model closely replicates in vivo TBI but with advantages gained in vitro. We anticipate that a combined in vitro approach with optical strain mapping will provide a more detailed understanding of the dependence of brain cell injury and death on strain and strain rate.
Collapse
|
169
|
Tan ST, Hung CT. Acute-on-chronic subdural haematoma: a rare complication after spinal anaesthesia. Hong Kong Med J 2003; 9:384-6. [PMID: 14530536] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 04/27/2023] Open
Abstract
An 88-year-old woman with an undiagnosed chronic subdural haematoma underwent emergency repair of a femoral hernia under spinal anaesthesia. The patient complained of headache postoperatively, and a subsequent computed tomography brain scan showed an acute-on-chronic subdural haematoma, with midline shift and impending coning. The patient recovered completely after surgical decompression. The difficulty in diagnosing chronic subdural haematoma in the elderly patient with no history of trauma is discussed, along with the differential diagnosis of headache following spinal anaesthetic in this age-group.
Collapse
|
170
|
Mauck RL, Nicoll SB, Seyhan SL, Ateshian GA, Hung CT. Synergistic Action of Growth Factors and Dynamic Loading for Articular Cartilage Tissue Engineering. ACTA ACUST UNITED AC 2003; 9:597-611. [PMID: 13678439 DOI: 10.1089/107632703768247304] [Citation(s) in RCA: 264] [Impact Index Per Article: 12.6] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/12/2022]
Abstract
It has previously been demonstrated that dynamic deformational loading of chondrocyte-seeded agarose hydrogels over the course of 1 month can increase construct mechanical and biochemical properties relative to free-swelling controls. The present study examines the manner in which two mediators of matrix biosynthesis, the growth factors TGF-beta1 and IGF-I, interact with applied dynamic deformational loading. Under free-swelling conditions in control medium (C), the [proteoglycan content][collagen content][equilibrium aggregate modulus] of cell-laden (10 x 10(6) cells/mL) 2% agarose constructs reached a peak of [0.54% wet weight (ww)][0.16% ww][13.4 kPa]c, whereas the addition of TGF-beta1 or IGF-I to the control medium led to significantly higher peaks of [1.18% ww][0.97% ww][23.6 kPa](C-TGF) and [1.00% ww][0.63% ww][19.3 kPa](C-IGF), respectively, by day 28 or 35 (p<0.01). Under dynamic loading in control medium (L), the measured parameters were [1.10% ww][0.52% ww][24.5 kPa]L, and with the addition of TGF-beta1 or IGF-I to the control medium these further increased to [1.49% ww][1.07% ww][50.5 kPa](L-TGF) and [1.48% ww][0.81% ww][46.2 kPa](L-IGF), respectively (p<0.05). Immunohistochemical staining revealed that type II collagen accumulated primarily in the pericellular area under free-swelling conditions, but spanned the entire tissue in dynamically loaded constructs. Applied in concert, dynamic deformational loading and TGF-beta1 or IGF-I increased the aggregate modulus of engineered constructs by 277 or 245%, respectively, an increase greater than the sum of either stimulus applied alone. These results support the hypothesis that the combination of chemical and mechanical promoters of matrix biosynthesis can optimize the growth of tissue-engineered cartilage constructs.
Collapse
|
171
|
Chafik D, Bear D, Bui P, Patel A, Jones NF, Kim BT, Hung CT, Gupta R. Optimization of Schwann cell adhesion in response to shear stress in an in vitro model for peripheral nerve tissue engineering. TISSUE ENGINEERING 2003; 9:233-41. [PMID: 12740086 DOI: 10.1089/107632703764664701] [Citation(s) in RCA: 23] [Impact Index Per Article: 1.1] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 02/02/2023]
Abstract
The design of nerve guidance channels (NGCs) is evolving to produce a favorable environment for neural regeneration. We created an in vitro model to evaluate the interactions between three centrally important components of this altered host environment: (1). Schwann cells, (2). substrate, and (3). sustained mechanical stimulus in the form of shear stress with laminar fluid flow. Preconfluent Schwann cells were plated on slides coated either with laminin, poly-D-lysine, type IV collagen, or fibronectin. These slides were placed into custom-designed, parallel-plate, flow chambers and were administered laminar fluid flow at a rate of 15 mL/min for 2 h. Schwann cell adhesion assays demonstrated that laminin (mean, 86.1%; SEM, 4.47%) and fibronectin (mean, 81.7%; SEM, 3.24%) were statistically superior to collagen type IV (mean, 57.7%; SEM, 3.96%) and poly-D-lysine (mean, 58.0%; SEM, 4.97%) (p < 0.001). Fibronectin (mean, 12.20%; SEM, 0.374%) induced statistically greater Schwann cell proliferation than did laminin (mean, 8.14%; SEM, 0.682%) (p < 0.001). Therefore, we recommend that fibronectin should be used as an important component of NGCs with further in vivo studies. As mechanical stress is an integral part of the host environment, our study is the first to incorporate this factor into an in vitro model for peripheral nerve tissue engineering.
Collapse
|
172
|
Hung CT, LeRoux MA, Palmer GD, Chao PHG, Lo S, Valhmu WB. Disparate aggrecan gene expression in chondrocytes subjected to hypotonic and hypertonic loading in 2D and 3D culture. Biorheology 2003; 40:61-72. [PMID: 12454388] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 02/27/2023]
Abstract
The effects of hypotonic (180 mOsm) and hypertonic (580 mOsm) medium loading on chondrocyte aggrecan gene expression in 2D monolayer and 3D hydrogel culture (agarose or alginate) were studied. Aggrecan promoter activity was monitored using a luciferase reporter gene assay and transient transfection. Osmotic loading was observed to differentially affect promoter activity, with hypotonic loading generally producing at least a 40% elevation in promoter activity, except for the case of alginate where a 50% suppression was observed. Hypertonic loading produced at least a 35% decrease in activity for all cultures. Similar osmolality-induced changes to aggrecan mRNA levels were observed in monolayer cells using qPCR. Deletion of exon 1 blocked the sensitivity of monolayer cells to hypertonic but not hypotonic medium changes. Confocal microscopy measurements suggested that the degree of hypotonic swelling in cells encapsulated in 3D matrix was restricted compared to monolayer cells whereas the degree of hypertonic shrinking was similar under both culture conditions.
Collapse
|
173
|
Wang CCB, Chahine NO, Hung CT, Ateshian GA. Optical determination of anisotropic material properties of bovine articular cartilage in compression. J Biomech 2003; 36:339-53. [PMID: 12594982 PMCID: PMC2809654 DOI: 10.1016/s0021-9290(02)00417-7] [Citation(s) in RCA: 104] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/27/2022]
Abstract
The precise nature of the material symmetry of articular cartilage in compression remains to be elucidated. The primary objective of this study was to determine the equilibrium compressive Young's moduli and Poisson's ratios of bovine cartilage along multiple directions (parallel and perpendicular to the split line direction, and normal to the articular surface) by loading small cubic specimens (0.9 x 0.9 x 0.8 mm, n =15) in unconfined compression, with the expectation that the material symmetry of cartilage could be determined more accurately with the help of a more complete set of material properties. The second objective was to investigate how the tension-compression nonlinearity of cartilage might alter the interpretation of material symmetry. Optimized digital image correlation was used to accurately determine the resultant strain fields within the specimens under loading. Experimental results demonstrated that neither the Young's moduli nor the Poisson's ratios exhibit the same values when measured along the three loading directions. The main findings of this study are that the framework of linear orthotropic elasticity (as well as higher symmetries of linear elasticity) is not suitable to describe the equilibrium response of articular cartilage nor characterize its material symmetry; a framework which accounts for the distinctly different responses of cartilage in tension and compression is more suitable for describing the equilibrium response of cartilage; within this framework, cartilage exhibits no lower than orthotropic symmetry.
Collapse
|
174
|
|
175
|
Wang CCB, Guo XE, Sun D, Mow VC, Ateshian GA, Hung CT. The functional environment of chondrocytes within cartilage subjected to compressive loading: a theoretical and experimental approach. Biorheology 2002; 39:11-25. [PMID: 12082263] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 02/25/2023]
Abstract
A non-invasive methodology (based on video microscopy, optimized digital image correlation and thin plate spline smoothing technique) has been developed to determine the intrinsic tissue stiffness (H(a)) and the intrinsic fixed charge density (c(0)(F)) distribution for hydrated soft tissues such as articular cartilage. Using this technique, the depth-dependent inhomogeneous parameters H(a)(z) and c(0)(F)(z) were determined for young bovine cartilage and incorporated into a triphasic mixture model. This model was then used to predict the mechanical and electrochemical events (stress, strain, fluid/osmotic pressure, and electrical potentials) inside the tissue specimen under a confined compression stress relaxation test. The integration of experimental measurements with theoretical analyses can help to understand the unique material behaviors of articular cartilage. Coupled with biological assays of cell-scale biosynthesis, there is also a great potential in the future to study chondrocyte mechanotransduction in situ with a new level of specificity.
Collapse
|