Antibacterial metals and alloys for potential biomedical implants

Investigating the Properties and Characterization of a Hybrid 3D Printed Antimicrobial Composite Material Using FFF Process: Innovative and Swift

Novel strategies and materials have gained the attention of researchers due to the current pandemic, the global market high competition, and the resistance of pathogens against conventional materials. There is a dire need to develop cost-effective, environmentally friendly, and biodegradable materials to fight against bacteria using novel approaches and composites. Fused filament fabrication (FFF), also known as fused deposition modeling (FDM), is the most effective and novel fabrication method to develop these composites due to its various advantages. Compared to metallic particles alone, composites of different metallic particles have shown excellent antimicrobial properties against common Gram-positive and Gram-negative bacteria. This study investigates the antimicrobial properties of two sets of hybrid composite materials, i.e., Cu-PLA-SS and Cu-PLA-Al, are made using copper-enriched polylactide composite, one-time printed side by-side with stainless steel/PLA composite, and second-time with aluminum/PLA composite respectively. These materials have 90 wt.% of copper, 85 wt.% of SS 17-4, 65 wt.% of Al with a density of 4.7 g/cc, 3.0 g/cc, and 1.54 g/cc, respectively, and were fabricated side by side using the fused filament fabrication (FFF) printing technique. The prepared materials were tested against Gram-positive and Gram-negative bacteria such as Escherichia coli (E. coli), Staphylococcus aureus (S. aureus), Pseudomonas aeruginosa (P. aeruginosa), Salmonella Poona (S. Poona), and Enterococci during different time intervals (5 min, 10 min, 20 min, 1 h, 8 h, and 24 h). The results revealed that both samples showed excellent antimicrobial efficiency, and 99% reduction was observed after 10 min. Hence, three-dimensional (3D) printed polymeric composites enriched with metallic particles can be utilized for biomedical, food packaging, and tissue engineering applications. These composite materials can also provide sustainable solutions in public places and hospitals where the chances of touching surfaces are higher.

Incorporation of Magnesium and Zinc Metallic Particles in PLGA Bi-layered Membranes with Sequential Ion Release for Guided Bone Regeneration

Guided bone regeneration (GBR) membranes are commonly used for periodontal tissue regeneration. Due to the complications of existing GBR membranes, the design of bioactive membranes is still relevant. GBR membranes with an asymmetric structure can accommodate the functional requirements of different interfacial tissues. Here, poly(lactic acid-glycolic acid) (PLGA) was selected as the matrix for preparing a bi-layered membrane with both dense and porous structure. The dense layer for blocking soft tissues was incorporated with zinc (Zn) particles, while the porous layer for promoting bone regeneration was co-incorporated with magnesium (Mg) and Zn particles. Mg/Zn-embedded PLGA membranes exhibited 166% higher mechanical strength in comparison with pure PLGA membranes and showed suitable degradation properties with a sequential ion release behavior of Mg²⁺ first and continuously Zn²⁺. More importantly, the release of Zn²⁺ from bi-layered PLGA endowed GBR membranes with excellent antibacterial activity (antibacterial rate > 69.3%) as well as good cytocompatibility with MC3T3-E1 (mouse calvaria pre-osteoblastic cells) and HGF-1 (human gingival fibroblast cells). Thus, the asymmetric bi-layered PLGA membranes embedded with Mg and Zn particles provide a simple and effective strategy to not only reinforce the PLGA membrane but also endow membranes with osteogenic and antibacterial activity due to the continuous ion release profile, which serves as a promising candidate for use in GBR therapy.

Antimicrobial efficacy and inactivation kinetics of a novel LED-based UV-irradiation technology

BACKGROUND

Ultraviolet (UV)-light-emitting diodes (UV-LEDs) are energy efficient and of special interest for the inactivation of micro-organisms. In the context of the coronavirus disease 2019 pandemic, novel UV technologies can offer a powerful alternative for effective infection prevention and control.

METHODS

This study assessed the antimicrobial efficacy of UV-C LEDs on Escherichia coli, Pseudomonas fluorescens and Listeria innocua, as well as severe acute respiratory syndrome coronavirus-2 (SARS-CoV-2), human immunodeficiency virus-1 (HIV-1) and murine norovirus (MNV), dried on inanimate surfaces, based on European Standard EN 17272.

RESULTS

This study found 90% inactivation rates for the tested bacteria at mean UV-C doses, averaged over all three investigated UV-C wavelengths, of 1.7 mJ/cm2 for E. coli, 1.9 mJ/cm2 for P. fluorescens and 1.5 mJ/cm2 for L. innocua. For the tested viruses, UV doses <15 mJ/cm2 resulted in 90% inactivation at wavelengths of 255 and 265 nm. Exposure of viruses to longer UV wavelengths, such as 275 and 285 nm, required much higher doses (up to 120 mJ/cm2) for inactivation. Regarding inactivation, non-enveloped MNV required much higher UV doses for all tested wavelengths compared with SARS-CoV-2 or HIV-1.

CONCLUSION

Overall, the results support the use of LEDs emitting at shorter wavelengths of the UV-C spectrum to inactivate bacteria as well as enveloped and non-enveloped viruses by exposure to the appropriate UV dose. However, low availability and excessive production costs of shortwave UV-C LEDs restricts implementation at present, and supports the use of longwave UV-C LEDs in combination with higher irradiation doses.

Surface Modification of Biomedical Ti-18Zr-15Nb Alloy by Atomic Layer Deposition and Ag Nanoparticles Decoration

Superelastic biocompatible alloys attract significant attention as novel materials for bone tissue replacement. These alloys are often composed of three or more components that lead to the formation of complex oxide films on their surfaces. For practical use, it is desirable to have a single-component oxide film with a controlled thickness on the surface of biocompatible material. Herein we investigate the applicability of the atomic layer deposition (ALD) technique for surface modification of Ti-18Zr-15Nb alloy with TiO₂ oxide. It was found that a 10-15 nm thick, low-crystalline TiO₂ oxide layer is formed by ALD method over the natural oxide film (~5 nm) of the Ti-18Zr-15Nb alloy. This surface consists of TiO₂ exclusively without any additions of Zr or Nb oxides/suboxides. Further, the obtained coating is modified by Ag nanoparticles (NPs) with a surface concentration up to 1.6% in order to increase the material's antibacterial activity. The resulting surface exhibits enhanced antibacterial activity with an inhibition rate of more than 75% against E. coli bacteria.

Porous Biocoatings Based on Diatomite with Incorporated ZrO2 Particles for Biodegradable Magnesium Implants

In the present work, the surface of a biodegradable Mg alloy was modified to create porous diatomite biocoatings using the method of micro-arc oxidation. The coatings were applied at process voltages in the range of 350-500 V. We have studied the influence of the addition of ZrO₂ microparticles on the structure and properties of diatomite-based protective coatings for Mg implants. The structure and properties of the resulting coatings were examined using a number of research methods. It was found that the coatings have a porous structure and contain ZrO₂ particles. The coatings were mostly characterized by pores less than 1 μm in size. However, as the voltage of the MAO process increases, the number of larger pores (5-10 μm in size) also increases. However, the porosity of the coatings varied insignificantly and amounted to 5 ± 1%. It has been revealed that the incorporation of ZrO₂ particles substantially affects the properties of diatomite-based coatings. The adhesive strength of the coatings has increased by approximately 30%, and the corrosion resistance has increased by two orders of magnitude compared to the coatings without zirconia particles.

Ti-30Nb-3Ag alloy with improved corrosion resistance and antibacterial properties for orthopedic and dental applications produced by mechanical alloying

Titanium alloys have gained popularity as a bioimplant material due to their biocompatibility, low modulus of elasticity, and increased strength. However, other issues, such as corrosion resistance, and infections can reduce the implant's lifespan. This paper aims to fabricate a new Ti-30Nb-3Ag at% alloy with enhanced in vitro corrosion and antibacterial properties by mechanical alloying (MA) followed by powder consolidation. XRD, SEM/EDX, and Vickers microhardness analyses were used to examine the phases compositions, microstructure, and microhardness, respectively. The in vitro corrosion performance of Ti-30Nb-3Ag alloy was inspected in a simulated body medium and artificial saliva. The alloy's antibacterial properties were evaluated in the gram-positive and negative bacterial medium. The results showed that after MA for 60 h, nanocrystalline β-Ti (BCC) and α-Ti (HCP) solid solutions were formed with crystallite sizes of 7.44 and 3.47 nm, respectively. The sintered sample exhibited densifications of 97%, with a microstructure composed of β-Ti, α-Ti, and a minor quantity of ultrafine Ti₂Ag phase. The microhardness result showed that Ti-30Nb-3Ag alloy possesses HV 491.5. Ti-30Nb-3Ag alloy has a potent antibacterial capability of 85.75% and 88.81% relative to Ti-6Al-4V alloy and CP-Ti, respectively. In vitro corrosion results revealed that the Ti-30Nb-3Ag alloy exhibited the widespread passive area in the investigated anodic regions and presented the highest impedance values in comparison with the commercial alloys, confirming its improved corrosion resistance performance in both studied mediums. Ti-30Nb-3Ag alloy possibly be a competitive bioimplant material for orthopedic and dental uses owing to its enhanced biocorrosion and antibacterial properties compared to commercial Ti-6Al-4V alloy and CP-Ti.

Novel Antibacterial Metals as Food Contact Materials: A Review

Food contamination caused by microorganisms is a significant issue in the food field that not only affects the shelf life of food, but also threatens human health, causing huge economic losses. Considering that the materials in direct or indirect contact with food are important carriers and vectors of microorganisms, the development of antibacterial food contact materials is an important coping strategy. However, different antibacterial agents, manufacturing methods, and material characteristics have brought great challenges to the antibacterial effectiveness, durability, and component migration associated with the use security of materials. Therefore, this review focused on the most widely used metal-type food contact materials and comprehensively presents the research progress regarding antibacterial food contact materials, hoping to provide references for exploring novel antibacterial food contact materials.

Improvement implant osseointegration through nonthermal Ar/O2 plasma

This study investigated the effects of nonthermal Ar/O₂ plasma on the osseointegration of titanium implants. Through 8 weeks' in vivo evaluation of implants inserted into femoral bones of male Sprague-Dawley rats, the new bone mineralization apposition rate (MAR) is increased by 1.87 and 2.14 times for implants of smooth machined (SM) and sand-blasted and acid-etched (SLA) after plasma treatment. The bone volume fraction (bone volume/total volume, BV/TV) and bone-implant contact (BIC) ratios are improved by 1.31, 1.26 times and 1.35, 1.15 times after 90 s plasma treatment. The improved hydrophilicity rather than implant surface morphology is believed to play a critical role for the osseointegration improvement.

Corrosion Behavior and Bio-Functions of the Ultrafine-Grained Ti6Al4V-5Cu Alloy with a Dual-Phase Honeycomb Shell Structure in Simulated Body Fluid

Titanium alloys are widely used in biomedical applications. However, cases of implant failure due to fatigue fracture and bacterial infection are common. In addition, implants are susceptible to metal ions (Al, V) released by long-term exposure to human body fluids, which causes neuropathy, mental disorders, and other diseases. Thus, development of novel materials to achieve long-term safety of implants is currently a research hotspot. Recently, our research group has developed an ultrafine-grained Ti6Al4V-5Cu alloy with a unique "dual-phase honeycomb shell" (DPHS) structure, which possesses high fatigue strength and stability. This study further affirmed its higher corrosion behavior, antibacterial properties, and cytocompatibility compared to the coarse-grained Ti6Al4V and Ti6Al4V-5Cu alloys. The ultrafine-grained structure of Ti6Al4V-5Cu having DPHS increased the proportion of phases (Cu-rich phases, β-phase, and Ti₂Cu intermetallic phase) with a lower surface potential. It was observed that the developed microstructure was conducive to a stable configuration of the oxide (passive) layer on the alloy surface. In addition, the low-phase interfacial energies of the ultrafine-grained structure with DPHS even facilitated the improvement of the denseness of the protective passive film and eventually enhanced the corrosion behavior. Besides, the fine-Cu-rich phases and the micro-galvanic couples formed between them and the matrix significantly increased the contact frequency of bacteria, thus increasing the contact sterilization efficiency of the ultrafine-grained Ti6Al4V-5Cu alloy. These results showed that the new ultrafine-grained Ti6Al4V-5Cu alloy has excellent corrosion resistance and biological functions for clinical application.

Recent progress of antibacterial hydrogels in wound dressings

Hydrogels are essential biomaterials due to their favorable biocompatibility, mechanical properties similar to human soft tissue extracellular matrix, and tissue repair properties. In skin wound repair, hydrogels with antibacterial functions are especially suitable for dressing applications, so novel antibacterial hydrogel wound dressings have attracted widespread attention, including the design of components, optimization of preparation methods, strategies to reduce bacterial resistance, etc. In this review, we discuss the fabrication of antibacterial hydrogel wound dressings and the challenges associated with the crosslinking methods and chemistry of the materials. We have investigated the advantages and limitations (antibacterial effects and antibacterial mechanisms) of different antibacterial components in the hydrogels to achieve good antibacterial properties, and the response of hydrogels to stimuli such as light, sound, and electricity to reduce bacterial resistance. Conclusively, we provide a systematic summary of antibacterial hydrogel wound dressings findings (crosslinking methods, antibacterial components, antibacterial methods) and an outlook on long-lasting antibacterial effects, a broader antibacterial spectrum, diversified hydrogel forms, and the future development prospects of the field.

Antifouling and antibacterial performance evaluation of polyethersulfone membranes modified with AZ63 alloy

Antibacterial membranes have attracted researchers' interest in recent years as a possible approach for dealing with biofouling on the membrane surface. This research aims to see if blending AZ63 Mg alloy into a polyethersulphone (PES) membrane can improve antifouling and separation properties. The composite membranes' pure water flux continued to increase from pristine PES to PES/AZ63 2.00 wt%. The results showed that PES/AZ63 2.00 wt% membrane supplied the highest permeate flux of E. coli. The steady-state fluxes of AZ63 composite membranes were 113.24, 104.38 and 44.79 L/m²h for PES/AZ63 2.00 wt%, 1.00 wt%, and 0.50 wt%, respectively. The enhanced biological activity of AZ63 was studied based on antioxidant activity, DNA cleavage, antimicrobial, anti-biofilm, bacterial viability inhibition and photodynamic antimicrobial therapy studies. The maximum DPPH scavenging activity was determined as 81.25% with AZ63. AZ63 indicated good chemical nuclease activity and also showed moderate antimicrobial activity against studied strains. The highest biofilm inhibition of AZ63 was 83.25% and 71.63% towards P. aeruginosa and S. aureus, respectively. The cell viability inhibition activity of AZ63 was found as 96.34% against E. coli. The photodynamic antimicrobial therapy results displayed that AZ63 demonstrated 100% bacterial inhibition when using E. coli.

Craniofacial therapy: advanced local therapies from nano-engineered titanium implants to treat craniofacial conditions

Nano-engineering-based tissue regeneration and local therapeutic delivery strategies show significant potential to reduce the health and economic burden associated with craniofacial defects, including traumas and tumours. Critical to the success of such nano-engineered non-resorbable craniofacial implants include load-bearing functioning and survival in complex local trauma conditions. Further, race to invade between multiple cells and pathogens is an important criterion that dictates the fate of the implant. In this pioneering review, we compare the therapeutic efficacy of nano-engineered titanium-based craniofacial implants towards maximised local therapy addressing bone formation/resorption, soft-tissue integration, bacterial infection and cancers/tumours. We present the various strategies to engineer titanium-based craniofacial implants in the macro-, micro- and nano-scales, using topographical, chemical, electrochemical, biological and therapeutic modifications. A particular focus is electrochemically anodised titanium implants with controlled nanotopographies that enable tailored and enhanced bioactivity and local therapeutic release. Next, we review the clinical translation challenges associated with such implants. This review will inform the readers of the latest developments and challenges related to therapeutic nano-engineered craniofacial implants.

Enhancement of Fracture Toughness in carbonate doped Hydroxyapatite based nanocomposites: Rietveld analysis and Mechanical behaviour

Highly nanocrystalline carbonated hydroxyapatite (CHAp) is synthesized by hydrothermal technique with four different stoichiometric compositions for microstructural and mechanical analysis. HAp is one of the most biocompatible material and addition of carbonate ions lead to increase in fracture toughness highly required in biomedical applications. The structural properties and its purity as single phase is confirmed by X-ray diffraction. Lattice imperfections and structural defects is investigated using XRD pattern model simulation, i.e. Rietveld's analysis. The substitution of CO₃^2- in HAp structure leads to a decrease in crystallinity which ultimately lessens crystallite size of sample as verified by XRD analysis. FE-SEM micrographs confirms the formation of nanorods with cuboidal morphology and porous structure of HAp and CHAp samples. The particle size distribution histogram validates the constant decrease in size due to carbonate addition. The mechanical testing of prepared samples revealed the increase in mechanical strength from 6.12 MPa to 11.52 MPa due to the addition of carbonate content, which leads to a rise in fracture toughness, a significant property of an implant material from 2.93 kN to 4.22 kN. The cumulative effect of CO₃^2- substitution on HAp structure and mechanical properties has been generalized for the application as biomedical implant material or biomedical smart materials.

Antimicrobial particles based on Cu2ZnSnS4 monograins

In this research, Cu₂ZnSnS₄ (CZTS) particles were successfully fabricated via the molten salt approach from the copper, zinc and tin sulphides as raw precursors. SEM analysis revealed that CZTS particles are tetragonal-shaped with sharp edges, smooth flat plane morphology, and crystal size varying from 10.8 to 28.7 µm. The phase and crystalline structure of synthesized powders were investigated using XRD analysis, which confirms the presence of a tetragonal crystal structure kesterite phase. The chemical composition of CZTS particles was evaluated by EDX spectroscopy, which identified the nearly stoichiometric composition with an averaged formula of Cu_1.88Zn_1.04SnS_3.97. The TG/DTA-MS and ICP-OES analysis showed the possible decomposition pathways and predicted their degradation rate in aqueous solutions. The CZTS particles possessed highly effective concentration and time-dependent antimicrobial properties against medically relevant bacteria and yeast strains. The CZTS particles (1 g L^-1) exhibited over 95.7 ± 1.9% killing efficiency towards M. luteus. In contrast, higher dosages (3.5 and 5 g L^-1) led to its complete inactivation and reduced the P. aeruginosa cell viability to 43.2 ± 3.2% and 4.1 ± 1.1%, respectively. Moreover, the CZTS particles (0.5 g L^-1) are responsible for causing 54.8 ± 1.8% of C. krusei and 89.7 ± 2.1% of C. parapsilosis yeasts death within the 24 h of exposure, which expanded to almost 100% when yeasts were treated with two times higher CZTS concentration (1.0 g L^-1). The mechanism of action has been proposed and evidenced by monitoring the 2',7'-dichlorofluorescein (DCF) fluorescence, which revealed that the overproduction of reactive oxygen species (ROS) is responsible for microorganism death.

Preparation of Superhydrophobic Materials and Establishment of Anticorrosive Coatings on the Tinplate Substrate by Alkylation of Graphene Oxide

Corrosion of structural parts not only reduces the service life of the equipment but also causes safety accidents, so building a long-lasting anti-corrosion coating on its surface is the key to solving this problem. Under the action of alkali catalysis, n-octyltriethoxysilane (OTES), dimethyldimethoxysilane (DMDMS), and perfluorodecyltrimethoxysilane (FTMS) hydrolyzed and polycondensed co-modified graphene oxide (GO), modified to synthesize a self-cleaning superhydrophobic material fluorosilane-modified graphene oxide (FGO). The structure, film morphology, and properties of FGO were systematically characterized. The results showed that the newly synthesized FGO was successfully modified by long-chain fluorocarbon groups and silanes. FGO presented an uneven and rough morphology on the substrate surface, the water contact angle was 151.3°, and the rolling angle was 3.9°, which caused the coating to exhibit excellent self-cleaning function. Meanwhile, the epoxy polymer/fluorosilane-modified graphene oxide (E-FGO) composite coating adhered to the carbon structural steel's surface, and its corrosion resistance was detected by the Tafel curve and EIS impedance. It was found that the current density of the 10 wt% E-FGO coating (I_corr) was the lowest (1.087 × 10^-10 A/cm²), which was approximately 3 orders of magnitude lower than that of the unmodified epoxy coating. This was primarily due to the introduction of FGO, which formed a continuous physical barrier in the composite coating and gave the composite coating excellent hydrophobicity. This method might provide new ideas for advances in steel corrosion resistance in the marine sector.

A multi-enzyme-like activity exhibiting mussel-inspired nanozyme hydrogel for bacteria-infected wound healing

Bacterial infection, tissue hypoxia, and inflammatory and oxidative stress are several key problems in wound healing of chronic infections. Herein, a multi-enzyme-like activity exhibiting multifunctional hydrogel made up of mussel-inspired carbon dot reduced-Ag (CDs/AgNPs) and Cu/Fe-nitrogen-doped carbon (Cu,Fe-NC) was designed. Due to the loss of glutathione (GSH) and oxidase (OXD)-like activity of the nanozyme (decomposes O₂ to generate a superoxide anion radical (O₂˙^-) and hydroxyl radical production (˙OH)), the multifunctional hydrogel exhibited excellent antibacterial performance. More importantly, during the bacterial elimination within the inflammatory phase of wound healing, the hydrogel could act as a catalase (CAT)-like agent to supply adequate O₂ by catalyzing intracellular H₂O₂ for hypoxia abatement. The catechol groups on the CDs/AgNPs endowed them with the dynamic redox equilibrium properties of phenol-quinones, thus providing the hydrogel with mussel-like adhesion properties. The multifunctional hydrogel was shown to excellently promote bacterial infection wound healing and maximize the efficiency of nanozymes.

Effect of rare earth oxide microparticles on mechanical, corrosion, antibacterial, and hemolytic behavior of Mg-Hydroxyapatite composite for orthopedic applications - A preliminary in-vitro study

The current study focused on developing a multifunctional Mg-based biodegradable composite that mitigates the trade-off between strength, antibacterial, and cytotoxicity behavior for orthopedic bone implants. The composite has been reinforced with natural mineral-based Hydroxyapatite and rare earth oxide (REO): Neodymium oxide. The effect of different concentrations of REO on the mechanical, antibacterial, and corrosion properties was analyzed. The antibacterial properties were assessed against gram-positive B. Subtilis and gram-negative E. Coli bacterial pathogens. Moreover, the cytotoxicity of the composites was assessed via Hemolysis percentage calculations. In addition, the microstructure characterization was performed via FESEM, XRD, and EDS techniques, and different intermetallic phase formations were recorded. Contact angle measurements were done via the sessile drop method to analyze the impact of rare earth oxide on the surface properties of the synthesized composites and their relationship with bacterial adhesion. The corrosion studies and swelling rates were performed under PBS and DMEM solutions. The composite with the addition of 1.5% REO outperformed the experiments with a compressive strength of 126.4 MPa, and a corrosion rate less than 0.2 mm/yr. The corrosion rates and degree of swelling were seen to be more stable in DMEM solution as compared to PBS. Improved antibacterial rates were observed against both pathogens after the addition of REO along with a hemolysis percentage less than 5% for Mg-HA-1.5Nd₂ O₃ . The composites showed increased hydrophobicity (>75%) by the addition of 1.5% REO. Hence, it was concluded that REO (Nd₂ O₃ ) addition to the Mg-Hydroxyapatite composite is a feasible choice as a biomaterial for bone implant applications.

Multifunctional Bioinspired Bredigite-Modified Adhesive for Bone Fracture Healing

Despite recent advances in bone adhesives applied for full median sternotomy, the regeneration of bone defects has remained challenging since the healing process is hampered by poor adhesiveness, limited bioactivity, and lack of antibacterial functions. Bioinspired adhesives by marine organisms provide a novel concept to circumvent these problems. Herein, a dual cross-link strategy is employed in designing a multifaceted bioinspired adhesive consisting of a catechol amine-functionalized hyperbranched polymer (polydopamine-co-acrylate, PDA), bredigite (BR) nanoparticles, and Fe³⁺ ions. The hybrid adhesives exhibit strong adhesion to various substrates such as poly(methyl methacrylate), glass, bone, and skin tissues through synergy between irreversible covalent and reversible noncovalent cross-linking, depending on the BR content. Noticeably, the adhesion strength of hybrid adhesives containing 2 wt % BR nanoparticles to bone tissues is 2.3 ± 0.8 MPa, which is about 3 times higher than that of pure PDA adhesives. We also demonstrate that these hybrid adhesives not only are bioactive and accelerate in vitro bone-like apatite formation but also exhibit antibacterial properties against Staphylococcus aureus, depending on the BR concentration. Furthermore, the superior cellular responses in contact with hybrid adhesives, including improved human osteosarcoma MG63 cell spreading and osteogenic differentiation, are achieved owing to the appropriate ion release and flexibility of the cross-linked double-network adhesive. In summary, multifunctional hybrid PDA/BR adhesives with appreciable osteoconductive, mechanical, and antibacterial properties represent the potential applications for median sternotomy surgery as a bone tissue adhesive.

Endowing biodegradable Zinc implants with dual-function of antibacterial ability and osteogenic activity by micro-addition of Mg and Ag (≤ 0.1 wt.%)

Infection remains the devastating complications associated with surgical fixation of bones fractured during trauma. In this study, we report a low-alloyed Zn-Mg-Ag that simultaneously has optimized strength degeneration profiles during degradation, outstanding antibacterial efficacy and osteogenic activity. Our results showed that Zn-0.05Mg-0.1Ag alloy had favorable mechanical properties (UTS: 247.8 ± 1.6 MPa, Elong.: 35 ± 2.2 %) and presented a better hold of mechanical integrity than pure Zn during 28 days corrosion, 2.6 % vs. 18.7 % reduction. After one-year of natural aging, the alloy still preserved an elongation of 24.07 ± 3.84 %. As verified by microbial cultures, Zn-0.05Mg-0.1Ag alloy demonstrated high antibacterial performance against Gram-positive and Gram-negative strains, as well as antibiotic-resistant strains (MRSA) in vitro and in vivo due to the synergistic antibacterial actions of Zn²⁺ and Ag⁺. Meanwhile, Zn-Mg-Ag alloy also exhibited enhanced viability, osteogenic differentiation, and gene expressions of osteoblasts in vitro, as well as promoted osteogenic activity than pure Zn in the femoral condyle defect repair model. The co-releasing of Zn, Mg and Ag ions did not induce toxic side effects. Collectively, low alloyed Zn-0.05Mg-0.1Ag indicated long-lasting mechanical integrity during degradation, and presented the ability to synergistically inhibit bacteria and promote osteogenesis, possessing tremendous potential in treating implant-associated infections. STATEMENT OF SIGNIFICANCE: Infection after fracture fixation (IAFF) remains the most common and serious side effects of orthopedic surgery. Additionally, widespread antibiotic use contributes to the development of multi-drug resistant bacteria such as methicillin-resistant staphylococcus aureus (MRSA), which exacerbates IAFF treatment and prevention. IAFF treatment and prevention remain clinically challenging, so implants with dual antibacterial and osteogenic functions are in high demand. The antibacterial efficacy and osteogenic activity of low-alloyed Zn-Mg-Ag (≤0.1 wt.% Mg, Ag) alloys were investigated in vitro and in vivo. The results showed that micro addition of Mg and Ag could significantly improve osseointegration function, mechanical properties, and antibacterial performance. These quantification findings shed new light on the development and understanding of dual functional Zn-based orthopedic implants.

Photothermal Hydrogels for Promoting Infected Wound Healing

Photothermal therapies (PTT), with spatiotemporally controllable antibacterial capabilities without inducing resistance, have shown encouraging prospects in the field of infected wound treatments. As an important platform for PTT, photothermal hydrogels exhibit attractive advantages in the field of infected wound treatment due to their excellent biochemical properties and have been intensively explored in recent years. This review summarizes the progress of the photothermal hydrogels for promoting infected wound healing. Three major elements of photothermal hydrogels, i.e., photothermal materials, hydrogel matrix, and construction methods, are introduced. Furthermore, different strategies of photothermal hydrogels in the treatment of infected wounds are summarized. Finally, the challenges and prospects in the clinical treatment of photothermal hydrogels are discussed.

Effect of Heat Treatment on Osteoblast Performance and Bactericidal Behavior of Ti6Al4V(ELI)-3at.%Cu Fabricated by Laser Powder Bed Fusion

Cu addition to alloys for biomedical applications has been of great interest to reduce bacterial growth. In situ-alloyed Ti6Al4V(ELI)-3at.%Cu was successfully manufactured by laser powder bed fusion (L-PBF). Even so, post-heat treatments are required to avoid distortions and/or achieve required/desired mechanical and fatigue properties. The present study is focused on the investigation of microstructural changes in L-PBF Ti6Al4V(ELI)-3at.%Cu after stress relieving and annealing treatments, as well as their influence on osteoblast and bactericidal behavior. After the stress relieving treatment, a homogenously distributed β phase and CuTi₂ intermetallic precipitates were observed over the α' matrix. The annealing treatment led to the increase in amount and size of both types of precipitates, but also to phase redistribution along α lamellas. Although microstructural changes were not statistically significant, such increase in β and CuTi₂ content resulted in an increase in osteoblast proliferation after 14 days of cell culture. A significant bactericidal behavior of L-PBF Ti6Al4V(ELI)-3at.%Cu by means of ion release was found after the annealing treatment, provably due to the easier release of Cu ions from β phase. Biofilm formation was inhibited in all on Cu-alloyed specimens with stress relieving but also annealing treatment.

Novel Microbial Palladium Nanoparticles with a High Photothermal Effect for Antibacterial Applications

Novel biocompatible palladium nanoparticles (Pd-NPs) have been prepared by microorganisms via Bacillus megaterium Y-4. It was demonstrated that ultrasonication treatment of biologically reduced Pd-NPs impart a much higher absorption in NIR regions and a better photothermal conversion efficiency to the material. The as-prepared material showed excellent biocompatibility and antibacterial activity under NIR irradiation. In less than 10 min, the disinfection efficiency for a low dosage of Pd-NPs (20 mg/L) was 99.99% toward both Staphylococcus aureus and Escherichia coli. The exclusive and even dispersed microbial Pd-NPs display a high efficiency of photothermal conversion under the irradiation of NIR, which endows them with excellent antibacterial activity in a low dosage.

Highly Dispersed Cu Produced by Mechanical Stress-Activated Redox Reaction to Establish Galvanic Corrosion in Fe Implant

Fe has immense potential for biodegradable orthopedic applications, but it degrades slowly in the physiological environment. Inducing galvanic couple by alloying Cu to Fe using ball milling is a promising approach. However, the ductile nature of Cu leads to the cold welding of a large amount of Cu powder during ball milling, which makes it difficult to disperse uniformly in the Fe matrix. Here, a Fe-CuO implant with highly dispersed Cu particles in the matrix was developed by shift-speed ball milling and selective laser melting. Specifically, copper oxide (CuO) particles were selected as precursors and dispersed in Fe powders by ball milling since they were brittle and would not be cold-welded during ball milling. After further milling in higher energy, it was found that CuO particles reacted with Fe and generated Cu particles through a stress-activated redox reaction. Subsequently, the obtained powders were prepared into a Fe-CuO implant using selective laser melting. Microstructure examination revealed that the Cu phases in the implant were dispersed evenly in the Fe matrix, which was considered to establish a large number of galvanic couples and aggravated the galvanic corrosion tendency. Electrochemical tests indicated that the implant had improved performance in degradation behavior in terms of high corrosion current density (22.4 μA/cm²), low corrosion resistance (1319 Ω cm²), and good degradation stability. In addition, it presented antibacterial effects against Escherichia coli and Staphylococcus aureus by diffusion mechanisms with killing rates of 90.7 and 96.7%, respectively, as well as good cytocompatibility.

Current Advances and Applications of Tantalum Element in Infected Bone Defects

Infected bone defects (IBDs) cause significant economic and psychological burdens, posing a huge challenge to clinical orthopedic surgeons. Traditional approaches for managing IBDs possess inevitable shortcomings; therefore, it is necessary to develop new functionalized scaffolds. Tantalum (Ta) has been widely used in load-bearing orthopedic implants due to its good biocompatibility and corrosion resistance. However, undecorated Ta could only structurally repair common bone defects, which failed to meet the clinical needs of bacteriostasis for IBDs. Researchers have made great efforts to functionalize Ta scaffolds to enhance their antibacterial activity through various methods, including surface coating, alloying, and micro- and nanostructure modifications. Additionally, several studies have successfully utilized Ta to modify orthopedic scaffolds for enhanced antibacterial function. These studies remarkably extended the application range of Ta. Therefore, this review systematically outlines the advances in the fundamental and clinical application of Ta in the treatment of IBDs, focusing on the antibacterial properties of Ta, its functionalization for bacteriostasis, and its applications in the modification of orthopedic scaffolds. This study provides researchers with an overview of the application of Ta in the treatment of IBDs.

Sonochemical fabrication of gradient antibacterial materials based on Cu-Zn alloy

At present research, we highlight ultrasonic treatment as a new way to create materials with a gradient change of chemical or physical properties. We demonstrate the possibility to fabricate novel materials with biocide activity based on simple and cheap Cu-Zn alloy. In this research, we propose a green preparative technique for the sonication of an alloy in an alkali solution. The method leads to a significant visual change and differentiation of particles into three different fractions. Due to the chemical micro gradients in media near the solid surface under intensive sonication, fast formation of specific functional groups occurs on the particles' surface. The particles were studied X-ray diffraction analysis (XRD) analysis, the field-emission scanning electron microscope (SEM) as well as electron backscatter diffraction (EBSD) mode, X-ray Photoelectron Spectroscopy (XPS), the differential pulse anodic stripping voltammetry (DPASV) technique. A strong correlation of both methods proves a redistribution of copper ions from Fraction I to Fraction III that influence for the antibacterial properties of the prepared material. The different biocidal activity was demonstrated for each separated Fraction that could be related to their different phase content and ability to release the different types of ions.

The race for the optimal antimicrobial surface: perspectives and challenges related to plasma electrolytic oxidation coating for titanium-based implants

Plasma electrolytic oxidation (PEO) is a low-cost, structurally reliable, and environmentally friendly surface modification method for orthopedic and dental implants. This technique is successful for the formation of porous, corrosion-resistant, and bioactive coatings, besides introducing antimicrobial compounds easily. Given the increase in implant-related infections, antimicrobial PEO-treated surfaces have been widely proposed to surmount this public health concern. This review comprehensively discusses antimicrobial implant surfaces currently produced by PEO in terms of their in vitro and in vivo microbiological and biological properties. We present a critical [part I] and evidence-based [part II] review about the plethora of antimicrobial PEO-treated surfaces. The mechanism of microbial accumulation on implanted devices and the principles of PEO technology to ensure antimicrobial functionalization by one- or multi-step processes are outlined. Our systematic literature search showed that particular focus has been placed on the metallic and semi-metallic elements incorporated into PEO surfaces to facilitate antimicrobial properties, which are often dose-dependent, without leading to cytotoxicity in vitro. Meanwhile, there are concerns over the biocompatibility of PEO and its long-term antimicrobial effects in animal models. We clearly highlight the importance of using clinically relevant infection models and in vivo long-term assessments to guarantee the rational design of antimicrobial PEO-treated surfaces to identify the 'finish line' in the race for antimicrobial implant surfaces.

Antibacterial and Antibiofilm Activity of Nanostructured Copper Films Prepared by Ionized Jet Deposition

Metal coatings represent good strategies to functionalize surfaces/devices and limit bacterial contamination/colonization thanks to their pleiotropic activity and their ability to prevent the biofilm formation. Here, we investigated the antibacterial and antibiofilm capacity of copper coatings deposited through the Ionized Jet Deposition (IJD) on the Calgary Biofilm Device (CBD) against the growth of two gram-negative and two gram-positive pathogenic strains. Three areas (i.e., (+)Cu, (++)Cu, and (+++)Cu based on the metal amount) on the CBD were obtained, presenting nanostructured coatings with high surface homogeneity and increasing dimensions of aggregates from the CBD periphery to the centre. The coatings in (++)Cu and (+++)Cu were efficient against the planktonic growth of the four pathogens. This antibacterial effect decreased in (+)Cu but was still significant for most of the pathogens. The antibiofilm efficacy was significant for all the strains and on both coated and uncoated surfaces in (+++)Cu, whereas in (++)Cu the only biofilms forming on the coated surfaces were inhibited, suggesting that the decrease of the metal on the coatings was associated to a reduced metal ion release. In conclusion, this work demonstrates that Cu coatings deposited by IJD have antibacterial and antibiofilm activity against a broad range of pathogens indicating their possible application to functionalize biomedical devices.

Enhanced Bactericidal Effect of Calcinated Mg-Fe Layered Double Hydroxide Films Driven by the Fenton Reaction

Osteogenic and antibacterial abilities are the permanent pursuit of titanium (Ti)-based orthopedic implants. However, it is difficult to strike the right balance between these two properties. It has been proved that an appropriate alkaline microenvironment formed by Ti modified by magnesium-aluminum layered double hydroxides (Mg-Al LDHs) could achieve the selective killing of bacteria and promote osteogenesis. However, the existence of Al induces biosafety concerns. In this study, iron (Fe), an essential trace element in the human body, was used to substitute Al, and a calcinated Mg-Fe LDH film was constructed on Ti. The results showed that a proper local alkaline environment created by the constructed film could enhance the antibacterial and osteogenic properties of the material. In addition, the introduction of Fe promoted the Fenton reaction and could produce reactive oxygen species in the infection environment, which might further strengthen the in vivo bactericidal effect.

UV-Assisted Room-Temperature Fabrication of Lignin-Based Nanosilver Complexes for Photothermal-Mediated Sterilization

Green and controllable preparation of silver nanoparticles (AgNPs) remains a great challenge. In this work, ethanol-extracted lignin-based nanosilver composites (AgNPs@EL) were synthesized at room temperature with the assistance of ultraviolet (UV) radiation. The ethanol-extracted lignin (EL) could serve as natural dispersion carriers and reducing agents for AgNPs. The reducing ability of EL could be further improved under UV irradiation, which enables the rapid synthesis of AgNPs at room temperature. More importantly, due to the good photothermal conversion capacity of EL, AgNPs@EL exhibits remarkably enhanced photothermal performance and excellent photothermal antibacterial ability, which could cause 7.2 and 5.3 log₁₀ CFU/mL reduction against Escherichia coli and Staphylococcus aureus, respectively, under near-infrared (NIR) irradiation (808 nm, 1.8 W/cm²) for 5 min. Furthermore, the composite film obtained by impregnating bacterial cellulose onto AgNPs@EL solution also shows significantly improved mechanical properties and photothermal antimicrobial activity. Therefore, this work may provide insights into the design of lignin-based photothermal-mediated antimicrobial materials.

The progress in titanium alloys used as biomedical implants: From the view of reactive oxygen species

Titanium and Titanium alloys are widely used as biomedical implants in oral and maxillofacial surgery, due to superior mechanical properties and biocompatibility. In specific clinical populations such as the elderly, diabetics and patients with metabolic diseases, the failure rate of medical metal implants is increased significantly, putting them at increased risk of revision surgery. Many studies show that the content of reactive oxygen species (ROS) in the microenvironment of bone tissue surrounding implant materials is increased in patients undergoing revision surgery. In addition, the size and shape of materials, the morphology, wettability, mechanical properties, and other properties play significant roles in the production of ROS. The accumulated ROS break the original balance of oxidation and anti-oxidation, resulting in host oxidative stress. It may accelerate implant degradation mainly by activating inflammatory cells. Peri-implantitis usually leads to a loss of bone mass around the implant, which tends to affect the long-term stability and longevity of implant. Therefore, a great deal of research is urgently needed to focus on developing antibacterial technologies. The addition of active elements to biomedical titanium and titanium alloys greatly reduce the risk of postoperative infection in patients. Besides, innovative technologies are developing new biomaterials surfaces conferring anti-infective properties that rely on the production of ROS. It can be considered that ROS may act as a messenger substance for the communication between the host and the implanted material, which run through the entire wound repair process and play a role that cannot be ignored. It is necessary to understand the interaction between oxidative stress and materials, the effects of oxidative stress products on osseointegration and implant life as well as ROS-induced bactericidal activity. This helps to facilitate the development of a new generation of well-biocompatible implant materials with ROS responsiveness, and ultimately prolong the lifespan of implants.

Complexes of Cu-Polysaccharide of a Marine Red Microalga Produce Spikes with Antimicrobial Activity

Metal-polysaccharides have recently raised significant interest due to their multifunctional bioactivities. The antimicrobial activity of a complex of Cu₂O with the sulfated polysaccharide (PS) of the marine red microalga Porphyridium sp. was previously attributed to spikes formed on the complex surface (roughness). This hypothesis was further examined here using other Cu-PS complexes (i.e., monovalent-Cu₂O, CuCl and divalent-CuO, CuCl₂). The nanostructure parameters of the monovalent complexes, namely, longer spikes (1000 nm) and greater density (2000-5000 spikes/µm²) were found to be related to the superior inhibition of microbial growth and viability and biofilm formation. When Escherichia coli TV1061, used as a bioluminescent test organism, was exposed to the monovalent Cu-PS complexes, enhanced bioluminescence accumulation was observed, probably due to membrane perforation by the spikes on the surface of the complexes and consequent cytoplasmic leakage. In addition, differences were found in the surface chemistry of the monovalent and divalent Cu-PS complexes, with the monovalent Cu-PS complexes exhibiting greater stability (ζ-potential, FTIR spectra, and leaching out), which could be related to spike formation. This study thus supports our hypothesis that the spikes protruding from the monovalent Cu-PS surfaces, as characterized by their aspect ratio, are responsible for the antimicrobial and antibiofilm activities of the complexes.

Antibacterial Ti-Cu implants: A critical review on mechanisms of action

Titanium (Ti) has been widely used for manufacturing of bone implants because of its mechanical properties, biological compatibility, and favorable corrosion resistance in biological environments. However, Ti implants are prone to infection (peri-implantitis) by bacteria which in extreme cases necessitate painful and costly revision surgeries. An emerging, viable solution for this problem is to use copper (Cu) as an antibacterial agent in the alloying system of Ti. The addition of copper provides excellent antibacterial activities, but the underpinning mechanisms are still obscure. This review sheds light on such mechanisms and reviews how incorporation of Cu can render Ti-Cu implants with antibacterial activity. The review first discusses the fundamentals of interactions between bacteria and implanted surfaces followed by an overview of the most common engineering strategies utilized to endow an implant with antibacterial activity. The underlying mechanisms for antibacterial activity of Ti-Cu implants are then discussed in detail. Special attention is paid to contact killing mechanisms because the misinterpretation of this mechanism is the root of discrepancies in the literature.

Corrosion Behavior and Biocompatibility of Hot-Extruded Mg-Zn-Ga-(Y) Biodegradable Alloys

Fixation screws and other temporary magnesium alloy fixation devices are used in orthopedic practice because of their biodegradability, biocompatibility and acceptable biodegradation rates. The substitution of dissolving implant by tissues during the healing process is one of the main requirements for biodegradable implants. Previously, clinical tests showed the effectiveness of Ga ions on bone tissue regeneration. This work is the first systematic study on the corrosion rate and biocompatibility of Mg-Zn-Ga-(Y) alloys prepared by hot extrusion, where Ga is an additional major alloying element, efficient as a bone-resorption inhibitor. Most investigated alloys have a low corrosion rate in Hanks' solution close to ~0.2 mm/year. No cytotoxic effects of Mg-2Zn-2Ga (wt.%) alloy on MG63 cells were observed. Thus, considering the high corrosion resistance and good biocompatibility, the Mg-2Zn-2Ga alloy is possible for applications in osteosynthesis implants with improved bone tissue regeneration ability.

Feasibility study on Ti-15Mo-7Cu with low elastic modulus and high antibacterial property

Titanium and titanium alloy with low density, high specific strength, good biological, excellent mechanical compatibility and easy to process have been widely used in the medical materials, but their application in orthopedics and dentistry often face bacterial infection, corrosion failure and stress shielding. In this paper, Ti-15Mo-7Cu (TM-7Cu) alloy was prepared by high vacuum non-consumable electric arc melting furnace and then treated by solution and aging treatment. The microstructure, mechanical properties, antibacterial properties and cytocompatibility were studied by X-ray diffraction, microhardness tester, electrochemical working station, antibacterial test and Live/Dead staining technology. The results have shown that the heat treatment significantly influenced the phase transformation, the precipitation of Ti₂Cu phase, the elastic modulus and the antibacterial ability. With the extension of the aging time, the elastic modulus slightly increased and the antibacterial rate obviously increased. TM-7Cu alloy with a low elastic modulus of 83GPa and a high antibacterial rate of > 93% was obtained. TM-7Cu alloy showed no cytotoxicity to MC3T3. It was suggested that TM-7Cu might be a highly competitive medical material.

Enzyme-triggered smart antimicrobial drug release systems against bacterial infections

The rapid emergence and spread of drug-resistant bacteria, as one of the most pressing public health threats, are declining our arsenal of available antimicrobial drugs. Advanced antimicrobial drug delivery systems that can achieve precise and controlled release of antimicrobial agents in the microenvironment of bacterial infections will retard the development of antimicrobial resistance. A variety of extracellular enzymes are secreted by bacteria to destroy physical integrity of tissue during their invasion of host body, which can be utilized as stimuli to trigger "on-demand" release of antimicrobials. In the past decade, such bacterial enzyme responsive drug release systems have been intensively studied but few review has been released. Herein, we systematically summarize the recent progress of smart antimicrobial drug delivery systems triggered by bacteria secreted enzymes such as lipase, hyaluronidase, protease and antibiotic degrading enzymes. The perspectives and existing key issues of this field will also be discussed to fuel the innovative research and translational application in the future.

Recent developments in antibacterial or antibiofilm compound coating for biliary stents

Cholestasis of the indwelling biliary stents usually leads to stone recurrence after endoscopic retrograde cholangio pancreatoraphy (ERCP). Biliary stents, including metallic and none-degradable plastic stents are widely used in clinical settings due to their many excellent properties. However, conventional biliary stents still suffer from poor antibacterial activity and anti-bile-adhesion, which lead to injured, local fibroblasts proliferating. Currently, various coatings for biliary stents have been prepared to meet the clinical demands. In this review, we start by summarizing and discussing classifications of biliary stents and antibacterial/antibiofilm mechanism. Then, the latest advances about developing antibacterial and antibiofilm coatings for improving the properties of biliary stents are reviewed and discussed in detail. Lastly, we list several possible directions for future development of biliary stents coatings and biliary stent, such as anti-bile-adhesion coating, multifunctional coating, drug-eluting biodegradable biliary stents and 3D printed biliary stents.

Gallium containing bioactive materials: A review of anticancer, antibacterial, and osteogenic properties

The incorporation of gallium into bioactive materials has been reported to enhance osteogenesis, to influence blood clotting, and to induce anti-cancer and anti-bacterial activity. Gallium-doped biomaterials prepared by various techniques include melt-derived and sol-gel-derived bioactive glasses, calcium phosphate bioceramics, metals and coatings. In this review, we summarize the recently reported developments in antibacterial, anticancer, osteogenesis, and hemostasis properties of Ga-doped biomaterials and briefly outline the mechanisms leading to Ga biological effects. The key finding is that gallium addition to biomaterials has great potential for treating bone-related diseases since it can be efficiently transferred to the desired region at a controllable rate. Besides, it can be used as a potential substitute for antibiotics for the inhibition of infections during the initial and advanced phases of the wound healing process. Ga is also used as an anticancer agent due to the increased concentration of gallium around excessive cell proliferation (tumor) sites. Moreover, we highlight the possibility to design different therapeutic approaches aimed at increasing the efficiency of the use of gallium containing bioactive materials for multifunctional applications.

Advances of Cobalt Nanomaterials as Anti-Infection Agents, Drug Carriers, and Immunomodulators for Potential Infectious Disease Treatment

Infectious diseases remain the most serious public health issue, which requires the development of more effective strategies for infectious control. As a kind of ultra-trace element, cobalt is essential to the metabolism of different organisms. In recent decades, nanotechnology has attracted increasing attention worldwide due to its wide application in different areas, including medicine. Based on the important biological roles of cobalt, cobalt nanomaterials have recently been widely developed for their attractive biomedical applications. With advantages such as low costs in preparation, hypotoxicity, photothermal conversion abilities, and high drug loading ability, cobalt nanomaterials have been proven to show promising potential in anticancer and anti-infection treatment. In this review, we summarize the characters of cobalt nanomaterials, followed by the advances in their biological functions and mechanisms. More importantly, we emphatically discuss the potential of cobalt nanomaterials as anti-infectious agents, drug carriers, and immunomodulators for anti-infection treatments, which might be helpful to facilitate progress in future research of anti-infection therapy.

Electrochemical Synthesis of Nanocrystalline CuAg Coatings on Stainless Steel from Cyanide-Free Electrolyte

Herein we demonstrate a novel plating bath, free from cyanide, to plate a highly adherent nanocrystalline copper-silver (ncCuAg) coating on a stainless-steel substrate and its application as an antimicrobial coating. The microstructures, such as the grain size, texture, microstrain, and the crystalline preferential orientation of CuAg deposits, are systematically investigated by X-ray diffraction analysis. The range of 13.4–16.6 nm was discovered to be the crystallite size determined from the X-ray peak broadening (Scherrer’s formula). Both HRTEM, FESEM-EDS, XPS, and mapping analysis revealed that the ncCuAg coatings are composed of both Ag and Cu atoms. Electrochemical processes occurring during CuAg co-deposition were investigated by using linear sweep voltammetry (LSV), cyclic voltammetry (CV), and anodic linear stripping voltammetry (ALSV). Additionally, the coatings made of ncCuAg produced by these baths work well as antibacterial agents against gram-positive (Staphylococcus) and gram-negative bacteria (Escherichia coli).

Generation of zinc ion-rich surface via in situ growth of ZIF-8 particle: Microorganism immobilization onto fabric surface for prohibit hospital-acquired infection

Viruses/bacteria outbreaks have motivated us to develop a fabric that will inhibit their transmission with high potency and long-term stability. By creating a metal-ion-rich surface onto polyester (PET) fabric, a method is found to inhibit hospital-acquired infections by immobilizing microorganisms on its surface. ZIF-8 and APTES are utilized to overcome the limitations associated with non-uniform distribution, weak biomolecule interaction, and ion leaching on surfaces. Modified surfaces employing APTES enhance ZIF-8 nucleation by generating a monolayer of self-assembled amine molecules. An in-situ growth approach is then used to produce evenly distributed ZIF-8 throughout it. In comparison with pristine fabric, this large amount of zinc obtained from the modification of the fabric has a higher affinity for interacting with membranes of microorganisms, leading to a 4.55-fold increase in coronavirus spike-glycoprotein immobilization. A series of binding ability stability tests on the surface demonstrate high efficiency of immobilization, >90%, of viruses and model proteins. The immobilization capacity of the modification fabric stayed unchanged after durability testing, demonstrating its durability and stability. It has also been found that this fabric surface modification approach has maintained air/vapor transmittance and air permeability levels comparable to pristine fabrics. These results strongly advocate this developed fabric has the potential for use as an outer layer of face masks or as a medical gown to prevent hospital-acquired infections.

FeMn with Phases of a Degradable Ag Alloy for Residue-Free and Adapted Bioresorbability

The development of bioresorbable materials for temporary implantation enables progress in medical technology. Iron (Fe)-based degradable materials are biocompatible and exhibit good mechanical properties, but their degradation rate is low. Aside from alloying with Manganese (Mn), the creation of phases with high electrochemical potential such as silver (Ag) phases to cause the anodic dissolution of FeMn is promising. However, to enable residue-free dissolution, the Ag needs to be modified. This concern is addressed, as FeMn modified with a degradable Ag-Calcium-Lanthanum (AgCaLa) alloy is investigated. The electrochemical properties and the degradation behavior are determined via a static immersion test. The local differences in electrochemical potential increase the degradation rate (low pH values), and the formation of gaps around the Ag phases (neutral pH values) demonstrates the benefit of the strategy. Nevertheless, the formation of corrosion-inhibiting layers avoids an increased degradation rate under a neutral pH value. The complete bioresorption of the material is possible since the phases of the degradable AgCaLa alloy dissolve after the FeMn matrix. Cell viability tests reveal biocompatibility, and the antibacterial activity of the degradation supernatant is observed. Thus, FeMn modified with degradable AgCaLa phases is promising as a bioresorbable material if corrosion-inhibiting layers can be diminished.

Comparative Experimental Investigation of Biodegradable Antimicrobial Polymer-Based Composite Produced by 3D Printing Technology Enriched with Metallic Particles

Due to the prevailing existence of the COVID-19 pandemic, novel and practical strategies to combat pathogens are on the rise worldwide. It is estimated that, globally, around 10% of hospital patients will acquire at least one healthcare-associated infection. One of the novel strategies that has been developed is incorporating metallic particles into polymeric materials that neutralize infectious agents. Considering the broad-spectrum antimicrobial potency of some materials, the incorporation of metallic particles into the intended hybrid composite material could inherently add significant value to the final product. Therefore, this research aimed to investigate an antimicrobial polymeric PLA-based composite material enhanced with different microparticles (copper, aluminum, stainless steel, and bronze) for the antimicrobial properties of the hybrid composite. The prepared composite material samples produced with fused filament fabrication (FFF) 3D printing technology were tested for different time intervals to establish their antimicrobial activities. The results presented here depict that the sample prepared with 90% copper and 10% PLA showed the best antibacterial activity (99.5%) after just 20 min against different types of bacteria as compared to the other samples. The metallic-enriched PLA-based antibacterial sheets were remarkably effective against Staphylococcus aureus and Escherichia coli; therefore, they can be a good candidate for future biomedical, food packaging, tissue engineering, prosthetic material, textile industry, and other science and technology applications. Thus, antimicrobial sheets made from PLA mixed with metallic particles offer sustainable solutions for a wide range of applications where touching surfaces is a big concern.

Bio-high entropy alloys: Progress, challenges, and opportunities

With the continuous progress and development in biomedicine, metallic biomedical materials have attracted significant attention from researchers. Due to the low compatibility of traditional metal implant materials with the human body, it is urgent to develop new biomaterials with excellent mechanical properties and appropriate biocompatibility to solve the adverse reactions caused by long-term implantation. High entropy alloys (HEAs) are nearly equimolar alloys of five or more elements, with huge compositional design space and excellent mechanical properties. In contrast, biological high-entropy alloys (Bio-HEAs) are expected to be a new bio-alloy for biomedicine due to their excellent biocompatibility and tunable mechanical properties. This review summarizes the composition system of Bio-HEAs in recent years, introduces their biocompatibility and mechanical properties of human bone adaptation, and finally puts forward the following suggestions for the development direction of Bio-HEAs: to improve the theory and simulation studies of Bio-HEAs composition design, to quantify the influence of composition, process, post-treatment on the performance of Bio-HEAs, to focus on the loss of Bio-HEAs under actual service conditions, and it is hoped that the clinical application of the new medical alloy Bio-HEAs can be realized as soon as possible.