A review of experimental aspects of electrochemical immunosensors

Evaluation of current diagnostic methods for COVID-19

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is the agent responsible for the coronavirus disease of 2019 (COVID-19), which triggers lung failure, pneumonia, and multi-organ dysfunction. This enveloped, positive sense and single-stranded RNA virus can be transmitted through aerosol droplets, direct and indirect contacts. Thus, SARS-CoV-2 is highly contagious and has reached a pandemic level in a few months. Since COVID-19 has caused numerous human casualties and severe economic loss posing a global threat, the development of readily available, accurate, fast, and cost-effective diagnostic techniques in hospitals and in any places where humans spread the virus is urgently required. COVID-19 can be diagnosed by clinical findings and several laboratory tests. These tests may include virus isolation, nucleic acid-based molecular assays like real-time polymerase chain reactions, antigen or antibody-based immunological assays such as rapid immunochromatographic tests, enzyme-linked immunosorbent assays, immunofluorescence techniques, and indirect fluorescent antibody techniques, electrochemical sensors, etc. However, current methods should be developed by novel approaches for sensitive, specific, and accurate diagnosis of COVID-19 cases to control and prevent this outbreak. Thus, this review will cover an overview and comparison of multiple reports and commercially available kits that include molecular tests, immunoassays, and sensor-based diagnostic methods for diagnosis of COVID-19. The pros and cons of these methods and future perspectives will be thoroughly evaluated and discussed.

Integrated Experimental and Theoretical Studies on an Electrochemical Immunosensor

Electrochemical immunosensors (EIs) integrate biorecognition molecules (e.g., antibodies) with redox enzymes (e.g., horseradish peroxidase) to combine the advantages of immunoassays (high sensitivity and selectivity) with those of electrochemical biosensors (quantitative electrical signal). However, the complex network of mass-transfer, catalysis, and electrochemical reaction steps that produce the electrical signal makes the design and optimization of EI systems challenging. This paper presents an integrated experimental and modeling framework to address this challenge. The framework includes (1) a mechanistic mathematical model that describes the rate of key mass-transfer and reaction steps; (2) a statistical-design-of-experiments study to optimize operating conditions and validate the mechanistic model; and (3) a novel dimensional analysis to assess the degree to which individual mass-transfer and reaction steps limit the EI's signal amplitude and sensitivity. The validated mechanistic model was able to predict the effect of four independent variables (working electrode overpotential, pH, and concentrations of catechol and hydrogen peroxide) on the EI's signal magnitude. The model was then used to calculate dimensionless groups, including Damkohler numbers, novel current-control coefficients, and sensitivity-control coefficients that indicated the extent to which the individual mass-transfer or reaction steps limited the EI's signal amplitude and sensitivity.

Development of a novel electrochemical immuno-biosensor for circulating biomarkers of the inner ear

Current approaches for diagnosis of hearing or vestibular disorders are mostly based on physical examinations that cannot provide information about the exact location of cellular damage inside the inner ear. Therefore, there is a need for new diagnostic methods capable of identifying the sites of damage through the detection of inner ear blood-circulating biomarkers. Here, we developed the first biosensor platform for rapid detection of otolin-1 and prestin, blood-circulating proteins specifically expressed in the vestibule and cochlea, respectively. The platform was designed on a DNA-based immunoassay that employed conjugated antibodies for target protein recognition, which when bound, altered the DNA-DNA hybridization on the surface, resulting in generation of a concentration-dependent signal. The signal was recorded when the redox moiety brought to the surface by the target enabled a selective electrochemical output directly in whole blood. Signal amplification was acquired by employing high-curvature nanostructured electrodes for sensitive sample analysis at picomolar concentrations with a three-fold quantitative range. The combination of nanostructuring and optimum density of the probes on the surface provided low-picomolar detection limits while utilizing small 10 μL sample volume with a 10-min response time. The proposed immuno-biosensor is highly selective and quantitative and can easily be adapted for rapid detection of any blood-circulating protein using their specific antibodies as recognition elements.

Screen-Printed Electrode-Based Sensors for Food Spoilage Control: Bacteria and Biogenic Amines Detection

Food spoilage is caused by the development of microorganisms, biogenic amines, and other harmful substances, which, when consumed, can lead to different health problems. Foodborne diseases can be avoided by assessing the safety and freshness of food along the production and supply chains. The routine methods for food analysis usually involve long analysis times and complex instrumentation and are performed in centralized laboratories. In this context, sensors based on screen-printed electrodes (SPEs) have gained increasing importance because of their advantageous characteristics, such as ease of use and portability, which allow fast analysis in point-of-need scenarios. This review provides a comprehensive overview of SPE-based sensors for the evaluation of food safety and freshness, focusing on the determination of bacteria and biogenic amines. After discussing the characteristics of SPEs as transducers, the main bacteria, and biogenic amines responsible for important and common foodborne diseases are described. Then, SPE-based sensors for the analysis of these bacteria and biogenic amines in food samples are discussed, comparing several parameters, such as limit of detection, analysis time, and sample type.

Polychlorinated Biphenyl Electrochemical Aptasensor Based on a Diamond-Gold Nanocomposite to Realize a Sub-Femtomolar Detection Limit

Polychlorinated biphenyls (PCBs) with high toxicity, low lethal dose, and bioaccumulation have been inhibited for application in wide fields, and a highly efficient trace detection is thus greatly desirable. In this study, we produce dense Au-nanoparticles by twice sputtering and twice annealing (T-Au-NPs) on boron-doped diamond (BDD). The successful formation of T-Au-NPs/BDD nanocomposites was confirmed by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and X-ray photoelectron spectroscopy analysis. Based on T-Au-NPs/BDD, an electronic biosensor with aptamers is fabricated to detect trace polychlorinated biphenyl-77 (PCB-77) by electrochemical impedance. A good linear relationship in the range of femtomolar to micromolar and significantly low detection limit of sub-femtomolar level (0.32 fM) are realized based on the biosensor. The emphasis of this research lies in the key role of the diamond substrate in the biosensor. It is demonstrated that the biosensor has excellent sensitivity, specificity, stability, and recyclability, which are favorable for detecting the trace PCB-77 molecule. It is attributed to the important effect presented by the BDD substrate and the synergistic influence of T-Au-NPs combined with aptamers.

Redox Electrochemistry to Interrogate and Control Biomolecular Communication

Cells often communicate by the secretion, transport, and perception of molecules. Information conveyed by molecules is encoded, transmitted, and decoded by cells within the context of the prevailing microenvironments. Conversely, in electronics, transmission reliability and message validation are predictable, robust, and less context dependent. In turn, many transformative advances have resulted by the formal consideration of information transfer. One way to explore this potential for biological systems is to create bio-device interfaces that facilitate bidirectional information transfer between biology and electronics. Redox reactions enable this linkage because reduction and oxidation mediate communication within biology and can be coupled with electronics. By manipulating redox reactions, one is able to combine the programmable features of electronics with the ability to interrogate and modulate biological function. In this review, we examine methods to electrochemically interrogate the various components of molecular communication using redox chemistry and to electronically control cell communication using redox electrogenetics.

Label-Free Electrochemical Detection of DNA Hybridization: A Method for COVID-19 Diagnosis

This paper presents label-free electrochemical transduction as a suitable scheme for COVID-19-specific viral RNA/c-DNA detection, with an aim to facilitate point of care diagnosis. In lieu of this, we discuss the proposed electrochemical biosensing scheme, based on electrodeposited gold nanoparticles as the transducing elements. Specific to this approach, here, the protocols associated with the immobilization of the single-stranded probe nucleotide on to the biosensor, have also been laid out. This paper also discusses the methods of electrochemical analysis, to be used for data acquisition and subsequent calibration, in relation to target analyte detection. Towards facilitating portable diagnosis, development of miniaturized sensors and their integration with readout units have also been discussed.

Enzyme Immobilization on Nanomaterials for Biosensor and Biocatalyst in Food and Biomedical Industry

Enzymes exhibit a great catalytic activity for several physiological processes. Utilization of immobilized enzymes has a great potential in several food industries due to their excellent functional properties, simple processing and cost effectiveness during the past decades. Though they have several applications, they still exhibit some challenges. To overcome the challenges, nanoparticles with their unique physicochemical properties act as very attractive carriers for enzyme immobilization. The enzyme immobilization method is not only widely used in the food industry but is also a component methodology in the pharmaceutical industry. Compared to the free enzymes, immobilized forms are more robust and resistant to environmental changes. In this method, the mobility of enzymes is artificially restricted to changing their structure and properties. Due to their sensitive nature, the classical immobilization methods are still limited as a result of the reduction of enzyme activity. In order to improve the enzyme activity and their properties, nanomaterials are used as a carrier for enzyme immobilization. Recently, much attention has been directed towards the research on the potentiality of the immobilized enzymes in the food industry. Hence, the present review emphasizes the different types of immobilization methods that is presently used in the food industry and other applications. Various types of nanomaterials such as nanofibers, nanoflowers and magnetic nanoparticles are significantly used as a support material in the immobilization methods. However, several numbers of immobilized enzymes are used in the food industries to improve the processing methods which not only reduce the production cost but also the effluents from the industry.

Antibody-Electroactive Probe Conjugates Based Electrochemical Immunosensors

Suitable immobilization of a biorecognition element, such as an antigen or antibody, on a transducer surface is essential for development of sensitive and analytically reliable immunosensors. In this review, we report on (1) methods of antibody prefunctionalization using electroactive probes, (2) methods for immobilization of such conjugates on the surfaces of electrodes in electrochemical immunosensor construction and (3) the use of antibody-electroactive probe conjugates as bioreceptors and sensor signal generators. We focus on different strategies of antibody functionalization using the redox active probes ferrocene (Fc), anthraquinone (AQ), thionine (Thi), cobalt(III) bipyridine (Co(bpy)33+), Ru(bpy)32+ and horseradish peroxidase (HRP). In addition, new possibilities for antibody functionalization based on bioconjugation techniques are presented. We discuss strategies of specific, quantitative antigen detection based on (i) a sandwich format and (ii) a direct signal generation scheme. Further, the integration of different nanomaterials in the construction of these immunosensors is presented. Lastly, we report the use of a redox probe strategy in multiplexed analyte detection.

Electrochemical immunoassay for the detection of stress biomarkers

A rapid electrochemical immunoassay method was developed to detect and measure stress biomarkers (cortisol and cortisone) in two biological samples (Zebrafish whole-body and artificial saliva). This methodology utilizes an immunoassay approach taking advantage of the lock and key mechanism that is related to the antibody-antigen interaction depending on the reliable immobilization of the antibody labelled with ferrocene tags (Ab-Fc) on a modified tin-doped indium oxide (ITO) electrode using electrochemical instrumentation to build a POC platform. The limit of detection (LOD) obtained for this biosensor was 1.03 pg ml⁻¹ for cortisol and 0.68 pg ml⁻¹ for cortisone, respectively. The correlation coefficient was 0.9852 and 0.9841 for cortisol and cortisone, respectively with a linear concentration from (0-50 ng ml⁻¹) which covers the standard levels of stress hormones in both selected biological samples. The incubation time was investigated and 30 min was found to be the optimum incubation time. This time would be acceptable for the POC system as total process time can be determined within 35 min.

A Label-Free Immunosensor Based on Graphene Oxide/Fe3O4/Prussian Blue Nanocomposites for the Electrochemical Determination of HBsAg

In this article, a highly sensitive label-free immunosensor based on a graphene oxide (GO)/Fe3O4/Prussian blue (PB) nanocomposite modified electrode was developed for the determination of human hepatitis B surface antigen (HBsAg). In this electrochemical immunoassay system, PB was used as a redox probe, while GO/Fe3O4/PB nanocomposites and AuNPs were prepared and coated on screen-printed electrodes to enhance the detection sensitivity and to immobilize the hepatitis B surface antibody (HBsAb). The immunosensor was fabricated based on the principle that the decrease in peak currents of PB is proportional to the concentration of HBsAg captured on the modified immunosensor. The experimental results revealed that the immunosensor exhibited a sensitive response to HBsAg in the range of 0.5 pg·mL-1 to 200 ng·mL-1, and with a low detection limit of 0.166 pg·mL-1 (S/N = 3). Furthermore, the proposed immunosensor was used to detect several clinical serum samples with acceptable results, and it also showed good reproducibility, selectivity and stability, which may have a promising potential application in clinical immunoassays.

Metal-Organic Framework-Based Microfluidic Impedance Sensor Platform for Ultrasensitive Detection of Perfluorooctanesulfonate

The growing global concerns to public health from human exposure to perfluorooctanesulfonate (PFOS) require rapid, sensitive, in situ detection where current, state-of-the-art techniques are yet to adequately meet sensitivity standards of the real world. This work presents, for the first time, a synergistic approach for the targeted affinity-based capture of PFOS using a porous sorbent probe that enhances detection sensitivity by embedding it on a microfluidic platform. This novel sorbent-containing platform functions as an electrochemical sensor to directly measure PFOS concentration through a proportional change in electrical current (increase in impedance). The extremely high surface area and pore volume of mesoporous metal-organic framework (MOF) Cr-MIL-101 is used as the probe for targeted PFOS capture based on the affinity of the chromium center toward both the fluorine tail groups as well as the sulfonate functionalities as demonstrated by spectroscopic (NMR and XPS) and microscopic (TEM) studies. Answering the need for an ultrasensitive PFOS detection technique, we are embedding the MOF capture probes inside a microfluidic channel, sandwiched between interdigitated microelectrodes (IDμE). The nanoporous geometry, along with interdigitated microelectrodes, increases the signal-to-noise ratio tremendously. Further, the ability of the capture probes to interact with the PFOS at the molecular level and effectively transduce that response electrochemically has allowed us achieve a significant increase in sensitivity. The PFOS detection limit of 0.5 ng/L is unprecedented for in situ analytical PFOS sensors and comparable to quantification limits achieved using state-of-the-art ex situ techniques.

Label-Free Impedimetric Immunosensors Modulated by Protein A/Bovine Serum Albumin Layer for Ultrasensitive Detection of Salbutamol

The sensing properties of immunosensors are determined not only by the amount of immobilized antibodies but also by the number of effective antigen-binding sites of the immobilized antibody. Protein A (PA) exhibits a high degree of affinity with the Fc part of IgG antibody to feasibly produce oriented antibody immobilization. This work proposes a simple method to control the PA surface density on gold nanostructure (AuNS)-deposited screen-printed carbon electrodes (SPCEs) by mixing concentration-varied PA and bovine serum albumin (BSA), and to explore the effect of PA density on the affinity attachment of anti-salbutamol (SAL) antibodies by electrochemical impedance spectroscopy. A concentration of 100 μg/mL PA and 100 μg/mL BSA can obtain a saturated coverage on the 3-mercaptoproponic acid (MPA)/AuNS/SPCEs and exhibit a 50% PA density to adsorb the amount of anti-SAL, more than other concentration-varied PA/BSA-modified electrodes. Compared with the randomly immobilized anti-SAL/MPA/AuNS/SPCEs and the anti-SAL/PA(100 μg/mL):BSA(0 μg/mL)/MPA/AuNS/SPCE, the anti-SAL/PA(100 μg/mL): BSA(100 μg/mL)/MPA/AuNS/SPCE-based immunosensors have better sensing properties for SAL detection, with an extremely low detection limit of 0.2 fg/mL and high reproducibility (<2.5% relative standard deviation). The mixture of PA(100 μg/mL):BSA(100 μg/mL) for the modification of AuNS/SPCEs has great promise for forming an optimal protein layer for the oriented adsorption of IgG antibodies to construct ultrasensitive SAL immunosensors.

A self-assembled electrochemical immunosensor for ultra-sensitive detection of ochratoxin A in medicinal and edible malt

Trace residue of mycotoxins in complex medicinal and edible food matrices has brought huge challenges for the development of ultrasensitive analytical methods. Here, a green electrochemical immunosensor for the ultrasensitive detection of ochratoxin A (OTA) was fabricated by self-assembling a compact 2-mercaptoacetic (TGA) monolayer on the surface of the working Au electrode to form the Au/TGA/bovine serum aibumin (BSA)-OTA/anti-OTA monoclonal antibody composite probes for selective and ultra-sensitive detection of OTA based on indirect competitive principle and differential pulse voltammetry analysis. The electrochemical impedance spectroscopy and cyclic voltammetry methods were introduced to characterize the assemble situation of the TGA-modified Au electrode and optimize some critical parameters for the green electrochemical immunoseonsor. Under the optimal conditions, the developed immunosensor exhibited much lower limit of detection (0.08 ng/mL) in the range of 0.1-1.0 ng/mL for OTA compared with other direct or disposable electrochemical immunosensors. Real application in the spiked malt samples verified high accuracy with no matrix interferences of the proposed immunoseonsor. This is a meaningful study on a self-assembled electrochemical immunoseonsor for ultra-sensitive and rapid detection of OTA in malt samples, which suggested a general simple-to-use sensing platform and prospect as an economical and green tool for ultra-sensitive detection of much more trace-level of toxic small molecules in other complex matrices to ensure their quality and safety.

Electrochemical enzyme-linked immunosorbent assay (e-ELISA) for parasitic nematode Ostertagia ostertagi (brown stomach worm) infections in dairy cattle

A sensitive electrochemical immunoassay (e-ELISA) has been developed for the detection of the gastrointestinal parasitic nematode Ostertagia ostertagi (brown stomach worm) in infected and control serum samples. An antigen-indirect immunoassay format was employed to detect the presence of O. ostertagi antibodies, coupled with an anti-species monoclonal horseradish peroxidase (HRP) conjugate. ABTS (2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid)) and TMB (3,3',5,5'-tetramethylbenzidine/hydrogen peroxide) were investigated as both chromogenic visualising reagents for optical ELISA and electroactive substrates for electrochemical ELISA in the HRP catalysed oxidation reaction. Coulometry was applied for the detection of O. ostertagi antibodies (via TMB electrochemistry) and compared with the commercial optical ELISA (ABTS based SVANOVIR® O. ostertagi-Ab ELISA kit). Cost-effective in-house sensors were designed and fabricated using polyester and chemical adhesive materials with the aid of stencil printing and laser machining techniques. The performance of the electrochemical ELISA and sensor was evaluated by investigating redox mediators (ABTS vs. TMB), stop solutions (sodium dodecyl sulfate vs. sulfuric acid) and incubation times (150 min vs. 70 min vs. 25 min). For a total assay incubation time of 70 minutes, the TMB/H2SO4 based e-ELISA was able to differentiate between positive (P) and negative (N) control serum samples, with a P/N70 control ratio 1.6 times higher than that of optical ELISA (TMB/H2SO4 combination) and 2.9 times higher than that of the commercial ELISA kit (ABTS/SDS combination). Furthermore, the e-ELISA approach is quicker and required only 25 min (total incubation time) with even better response (P/N25 = 14.7), which is approximately 4-fold higher than the optical immunoassay (P/N25 = 3.8). The proposed e-ELISA is specific (selective Ab-Ag interactions) and highly sensitive - capable of detecting up to 16-fold dilutions of a positive control serum sample. The electrochemical ELISA approach has the potential for rapid sample screening in a portable, disposable format, contributing to the quest for effective prevention and control of parasitic Ostertagia ostertagi infections in cattle.

Preparation and characterization of carboxymethyl cashew gum grafted with immobilized antibody for potential biosensor application

This report details the design of carboxymethylated cashew gum (CG) as a platform for antibody (Ab) immobilization, which can then be used as a biosensor for bacteria detection. The CG was isolated and characterized, followed by conversion to carboxymethyl cashew gum (CMCG). The CMCG film was a viable support for antibody immobilization; it was electrodeposited on gold surface using the cyclic voltammetry technique, applying a potential sweep from -1.0 V to 1.3 V with a scan rate of 50 mV s^-1 and 10 scans. The COOH groups on the surface of the film were critical in promoting Ab bonding. The immobilization of the Ab was mediated by protein A (PrA) for recognition of the antigen. Voltammetry studies were used to monitor the antibody immobilization. Finally, the analytical response of the CMCG-PrA-Ab system was evaluated with the chronoamperometry technique and was found to detect Salmonella Typhimurium bacteria rapidly and efficiently.

Biosensors on the road to early diagnostic and surveillance of Alzheimer's disease

Alzheimer's disease is a debilitating and largely untreatable condition with subtle onset and slow progression over an extensive period of time, which culminate in increasing levels of disability. As Alzheimer's disease prevalence is expected to grow exponentially in the upcoming decades, there is an urgency to develop analytical technologies for the sensitive, reliable and cost-effective detection of Alzheimer's disease biomarkers. Biosensors are powerful analytical devices that translate events of biological recognition on physical or chemical transducers into electrical, thermal or optical signals. The high sensitivity and selectivity of biosensors associated with easy, rapid and low-cost determination of analytes have made this discipline one of the most intensively studied in the past decades. This review centers on recent advances, challenges and trends of Alzheimer's disease biosensing particularly in the effort to combine the unique properties of nanomaterials with biorecognition elements. In the last decade, impressive progresses have been made towards the development of biosensors, mainly electrochemical and optical, for detection of Alzheimer's disease biomarkers in the pico- and femto-molar range. Nonetheless, advances in multiplexed detection, robustness, stability and specificity are still necessary to ensure an accurate and differentiated diagnosis of this disease.

An ultrasensitive immunosensor based on manganese dioxide-graphene nanoplatelets and core shell Fe3O4@Au nanoparticles for label-free detection of carcinoembryonic antigen

A novel electrochemical immunosensor was developed for label-free detection of carcinoembryonic antigen (CEA) as a cancer biomarker. The designed immunosensor was based on CEA antibody (anti-CEA) anchored with core shell Fe₃O₄@Au nanoparticles which were immobilized on a screen-printed carbon electrode modified with manganese dioxide decorating on graphene nanoplatelets (SPCE/GNP-MnO₂/Fe₃O₄@Au-antiCEA). The SPCE was placed onto a home-made electrode holder for easy handling. The approach was based on direct binding of CEA to a fixed amount of anti-CEA on the modified electrode for the specific detection using linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS) monitored in a solution containing 5 mM [Fe(CN)₆^3-/4-] prepared in 0.1 M phosphate buffer at pH 7.4. The difference in signal response owing to the redox reaction of [Fe(CN)₆]^3-/4- before and after interaction with CEA was regarded as the immunosensor response corresponding directly to the CEA concentration. Under optimized conditions, the linear range of 0.001-100 ng/mL, and the detection limits of 0.10 pg/mL (LSV) and 0.30 pg/mL (EIS) were evaluated. The applicability of the immunosensor was verified by well-corresponding determination of CEA in diluted human serum samples by electrochemiluminescence (ECL) immunoassay. Therefore, the proposed immunosensor could be suitable enough for a real sample analysis of CEA.

Preparation of a novel sandwich-type electrochemical immunosensor for AFP detection based on an ATRP and click chemistry technique

It is extremely important to explore the synthesis methodology and application scope of functional polymer brush-based nanocomposites.

Low-potential immunosensor-based detection of the vascular growth factor 165 (VEGF165) using the nanocomposite platform of cobalt metal–organic framework

The vascular endothelial growth factor 165 (VEGF₁₆₅) is a quintessential biomarker in cancers. An easy and precise tool for the early detection of malignancies is required for rapid care and metastasis prevention. Cobalt-based metal–organic framework (Co-BTC-GO-MOF) nanoparticles have been used as a signal carrier for the anti-VEGF₁₆₅ signaling antibody. Cobalt-based MOF was synthesized using cobalt (Co), benzene-1,3,5-tricarboxylate (BTC), and graphene oxide (GO) applying a hydrothermal method. Structure, compositions, size and morphology of the qualified sensor are determined by using distinctive analytical techniques. The Co-MOF nanoparticles are found to be thermostable, as revealed by thermal stability assay. The strategy utilises an impedimetric and differential pulse voltammetry (DPV) techniques in the presence of the [Fe(CN)₆]^3−/4− redox system. Compared to earlier results, this assay resulted in higher sensitivity with the limit of detection (LOD) found to be 5.23 pM in a 0.01 M buffer solution of pH 7.4 using linear scale voltammetry at room temperature. The resulting Co-BTC-GO-MOF immunosensor shows high responsiveness and selectivity in detecting VEGF₁₆₅ in real-time serum samples of cancer patients. The electrochemical performance studies confirm that the intended proposed immunosensor could pave the way for the future advancement of high-performance, sensitive, reproducible and robust immunosensors for the cost-effective and initial phase detection of cancer in the future.

The vascular endothelial growth factor 165 (VEGF₁₆₅) is a quintessential biomarker in cancers.

Highly sensitive and selective electrochemical immunosensors by substrate-enhanced electroless deposition of metal nanoparticles onto three-dimensional graphene@Ni foams

In this study, we have for the first time preformed the facile substrate-enhanced electroless deposition (SEED) of metal nanoparticles onto monolithic graphene@Ni foams for construction of disposable three-dimensional (3D) electrochemical immunosensors. Specifically, we firstly used the SEED method to deposit gold nanoparticles (AuNPs) onto the graphene@Ni foam for immobilization of antibody (Ab₁). This is followed by a second step SEED deposition to produce silver nanoparticles (AgNPs) for electrochemical stripping detection. Using α-fetoprotein antigen (AFP) as a module analyte, the newly-developed sensor showed a wide linear response, ranging from 5.0 pg/mL to 5.0 ng/mL and a low detection limit down to 2.3 pg/mL. The newly-developed 3D-immunosensor is sensitive, reliable, and easy to be fabricated, showing great potential for clinic applications.

Nanostructure-based Sensitive Electrochemical Immunosensors

It is well-known that electrochemical immunosensors have many advantages, including but not limited to high sensitivity, simplicity in application, low-cost production, automated control and potential miniaturization. Due to specific antigen–antibody recognition, electrochemical immunosensors also have provided exceptional possibilities for real-time trace detection of analytical biotargets, which consists of small molecules (such as natural toxins and haptens), macromolecules, cells, bacteria, pathogens or viruses. Recently, the advances in the development of electrochemical immunosensors can be classified into the following directions: the first is using electrochemical detection techniques (voltammetric, amperometric, impedance spectroscopic, potentiometric, piezoelectric, conductometric and alternating current voltammetric) to achieve high sensitivity regarding the electrochemical change of electrochemical signal transduction; the second direction is developing sensor configurations (microfluidic and paper-based platforms, microelectrodes and electrode arrays) for simultaneous multiplex high-throughput analyses; and the last is designing nanostructured materials serving as sensing interfaces to improve sensor sensitivity and selectivity. This chapter introduces the working principle and summarizes the state-of-the-art of electrochemical immunosensors during the past few years with practically relevant details for: (a) metal nanoparticle- and quantum dot-labeled immunosensors; (b) enzyme-labeled immunosensors; and (c) magnetoimmunosensors. The importance of various types of nanomaterials is also thoroughly reviewed to obtain an insight into understanding the theoretical basis and practical orientation for the next generation of diagnostic devices.

Nanostructures for nonlabeled and labeled electrochemical immunosensors: Simultaneous electrochemical detection of cancer markers: A review

The simultaneous electrochemical determination of multiple tumor antigens has attracted a great deal of attention, which can effectively enhance the capability and accuracy of the analysis. Nanostructured materials mostly played a key major role in the electrochemical immunosensors fabrication and operation improvement. This review focused mainly on the protocols for using nanostructures to fabricate electrochemical (nonlabeled@label-free and labeled@sandwich-type) immunosensors. Furthermore, this review has also described the diverse classes of electroactive nanospecies which are a complementary part of any immunosensor that assists to reach the selectivity for the target antigen. Finally, the important analytical characteristics of the published immunosensors were discussed (electrochemical detection technique, linear range, and detection limit). Studies published between the years 2009-2018 have been included in this review.

Current Trends in the Biosensors for Biological Warfare Agents Assay

Biosensors are analytical devices combining a physical sensor with a part of biological origin providing sensitivity and selectivity toward analyte. Biological warfare agents are infectious microorganisms or toxins with the capability to harm or kill humans. They can be produced and spread by a military or misused by a terrorist group. For example, Bacillus anthracis, Francisella tularensis, Brucella sp., Yersinia pestis, staphylococcal enterotoxin B, botulinum toxin and orthopoxviruses are typical biological warfare agents. Biosensors for biological warfare agents serve as simple but reliable analytical tools for the both field and laboratory assay. There are examples of commercially available biosensors, but research and development of new types continue and their application in praxis can be expected in the future. This review summarizes the facts and role of biosensors in the biological warfare agents' assay, and shows current commercially available devices and trends in research of the news. Survey of actual literature is provided.

The Role of Electrochemical Immunosensors in Clinical Analysis

An immunosensor is a kind of affinity biosensor based on interactions between an antigen and specific antigen immobilized on a transducer surface. Immunosensors possess high selectivity and sensitivity due to the specific binding between antibody and corresponding antigen, making them a suitable platform for several applications especially in the medical and bioanalysis fields. Electrochemical immunosensors rely on the measurements of an electrical signal recorded by an electrochemical transducer and can be classed as amperometric, potentiometric, conductometric, or impedimetric depending on the signal type. Among the immunosensors, electrochemical immunosensors have been more perfected due to their simplicity and, especially their ability to be portable, and for in situ or automated detection. This review addresses the potential of immunosensors destined for application in clinical analysis, especially cancer biomarker diagnosis. The emphasis is on the approaches used to fabricate electrochemical immunosensors. A general overview of recent applications of the developed electrochemical immunosensors in the clinical approach is described.

Electrochemical methods for detection of biomarkers of Chronic Obstructive Pulmonary Disease in serum and saliva

Chronic obstructive pulmonary disease (COPD) is the fourth leading cause of death nowadays, and its underdiagnosis is still a great challenge. More effective diagnosis method is in urgent need since the traditional spirometry has many limitations in the practical application. The electrochemical (EC) detection methods have their unique advantages of high accuracy, short response time and easy integration of the system. In this review, recent works on the EC methods for COPD biomarkers including interleukin 6 (IL-6), interleukin 8 (IL-8) and C-reactive protein (CRP) are summarized. Five types of EC methods are highlighted in this study, as enzyme-labelled immunosensors, nanoparticle-labelled immunosensors, capacitive or impedimetric immunosensors, magnetoimmunosensors, and field effect transistor (FET) immunosensors. To date, EC immunosensors have been exhibiting high analytical performance with a detection limit that can achieve several pg/mL or even lower. The simplicity of EC immunosensors makes them a perfect solution for a future point-of-care device to use in settings for COPD diagnosis and follow-up. Nevertheless, more efforts need to be paid on the simultaneous detection of multiple biomarkers, a demand for the clinical diagnosis, and processes of assay simplification towards achieving one-step detection.

An Electrochemical Sandwich Immunosensor for the Detection of HER2 using Antibody-Conjugated PbS Quantum Dot as a label

A facile electrochemical sandwich immunosensor for the detection of a breast cancer biomarker, the human epidermal growth factor receptor 2 (HER2), was designed, using lead sulfide quantum dots-conjugated secondary HER2 antibody (Ab2-PbS QDs) as a label. Using Ab2-PbS QDs in the development of electrochemical immunoassays leads to many advantages such as straightforward synthesis and well-defined stripping signal of Pb(II) through acid dissolution, which in turn yields better sensing performance for the sandwiched immunosensor. In the bioconjugation of PbS QDs, the available amine and hydroxyl groups from secondary anti-HER2 and capped PbS QDs were bound covalently together via carbonyldiimidazole (CDI) acting as a linker. In order to quantify the biomarker, SWV signal was obtained, where the Pb²⁺ ions after acid dissolution in HCl was detected. The plated mercury film SPCE was also detected in situ. Under optimal conditions, HER2 was detected in a linear range from 1-100 ng/mL with a limit of detection of 0.28 ng/mL. The measures of satisfactory recoveries were 91.3% to 104.3% for the spiked samples, displaying high selectivity. Therefore, this method can be applied to determine HER2 in human serum.

A label-free immunosensor based on PHEMA/graphene oxide nanocomposite for simultaneous electrochemical determination of alpha fetoprotein

An electrochemical immunosensor based on poly(2-hydroxyethyl methacrylate) (PHEMA)/graphene oxide (GO) nanocomposite was designed in a simple way for the ultrasensitive detection of tumor makers (alpha-fetoprotein, AFP as a model). PHEMA with excellent biocompatibility, provides a large number of sites for connecting signal molecules. After modification with signal molecules, the functional PHEMA significantly improved the sensitivity of electrochemical detection. In order to immobilize antibodies, GO was introduced and used to construct a nanocomposite as a substrate. The designed AFP immunosensor showed favorable selectivity and excellent stability. Meanwhile, it has a low detection limit of 0.403 pg mL-1. Furthermore, the immunosensor was used to detect target AFP in human serum, demonstrating the feasibility of clinical diagnosis.

Quick electrochemical immunoassay for hantavirus detection based on biochar platform

This work describes the first method using biochar (BC) as carbonaceous platform for immunoassay application. BC is a highly functionalized material obtained through biomass pyrolysis under controlled conditions. Due to the highly functionalized surface, covalent binding between BC and biomolecules can be performed by EDC/NHS conjugation. The application of the modified electrode was done with Hantavirus, that are etiologic agents mainly transmitted by wild rodents. Among its pathologies Hantavirus Cardiopulmonary Syndrome (HCPS) arises at Americas, caused by Hantavirus Araucária and reaches 40% lethality. The diagnostic is based on the presence of specific hantavirus nucleoprotein (Np), under viremic condition or IgG2b antibodies (Ab), during first symptoms. The results presented a device sensitivity of 5.28 μA dec^-1 and a LOD of 0.14 ng mL^-1 to the Np detection, ranging from 5.0 ng mL^-1 to 1.0 μg mL^-1, the Ab detection works as qualitative type sensor above 200 ng mL^-1. Both sensors were evaluated its selectivity and serum samples; selectivity against Gumboro disease, VP2 protein, and antibody IgG2a against Yellow fever disease (YF), respectively. So, the devices here proposed are promising tool suitable for both rodent and human hantavirus clinical surveys.

Electrochemical Immuno- and Aptasensors for Mycotoxin Determination

Modern analysis of food and feed is mostly focused on development of fast and reliable portable devices intended for field applications. In this review, electrochemical biosensors based on immunological reactions and aptamers are considered in the determination of mycotoxins as one of most common contaminants able to negatively affect human health. The characteristics of biosensors are considered from the point of view of general principles of bioreceptor implementation and signal transduction providing sub-nanomolar detection limits of mycotoxins. Moreover, the modern trends of bioreceptor selection and modification are discussed as well as future trends of biosensor development for mycotoxin determination are considered.

Trends and Perspectives in Immunosensors for Determination of Currently-Used Pesticides: The Case of Glyphosate, Organophosphates, and Neonicotinoids

Pesticides, due to their intensive use and their peculiar chemical features, can persist in the environment and enter the trophic chain, thus representing an environmental risk for the ecosystems and human health. Although there are several robust and reliable standard analytical techniques for their monitoring, the high frequency of contamination caused by pesticides requires methods for massive monitoring campaigns that are capable of rapidly detecting these compounds in many samples of different origin. Immunosensors represent a potential tool for simple, rapid, and sensitive monitoring of pesticides. Antibodies coupled to electrochemical or optical transducers have resulted in effective detection devices. In this review, the new trends in immunosensor development and the application of immunosensors for the detection of pesticides of environmental concern-such as glyphosate, organophosphates, and neonicotinoids-are described.

Suppressing Non-Specific Binding of Proteins onto Electrode Surfaces in the Development of Electrochemical Immunosensors

Electrochemical immunosensors, EIs, are systems that combine the analytical power of electrochemical techniques and the high selectivity and specificity of antibodies in a solid phase immunoassay for target analyte. In EIs, the most used transducer platforms are screen printed electrodes, SPEs. Some characteristics of EIs are their low cost, portability for point of care testing (POCT) applications, high specificity and selectivity to the target molecule, low sample and reagent consumption and easy to use. Despite all these attractive features, still exist one to cover and it is the enhancement of the sensitivity of the EIs. In this review, an approach to understand how this can be achieved is presented. First, it is necessary to comprise thoroughly all the complex phenomena that happen simultaneously in the protein-surface interface when adsorption of the protein occurs. Physicochemical properties of the protein and the surface as well as the adsorption phenomena influence the sensitivity of the EIs. From this point, some strategies to suppress non-specific binding, NSB, of proteins onto electrode surfaces in order to improve the sensitivity of EIs are mentioned.

Quantitative detection of procalcitonin using an electrochemical immunosensor based on MoO3/Au@rGO nanocomposites

In this work, a sandwich-type electrochemical immunosensor for the detection of procalcitonin (PCT) is constructed layer-by-layer with a novel label based on MoO₃/Au@rGO nanocomposites.

Disposable Voltammetric Immunosensors Integrated with Microfluidic Platforms for Biomedical, Agricultural and Food Analyses: A Review

Disposable immunosensors are analytical devices used for the quantification of a broad variety of analytes in different areas such as clinical, environmental, agricultural and food quality management. They detect the analytes by means of the strong interactions between antibodies and antigens, which provide concentration-dependent signals. For the herein highlighted voltammetric immunosensors, the analytical measurements are due to changes in the electrical signals on the surface of the transducers. The possibility of using disposable and miniaturized immunoassays is a very interesting alternative for voltammetric analyses, mainly, when associated with screen-printing technologies (screen-printed electrodes, SPEs), and microfluidic platforms. The aim of this paper is to discuss a carefully selected literature about different examples of SPEs-based immunosensors associated with microfluidic technologies for diseases, food, agricultural and environmental analysis. Technological aspects of the development of the voltammetric immunoassays such as the signal amplification, construction of paper-based microfluidic platforms and the utilization of microfluidic devices for point-of-care testing will be presented as well.

Dual-Mode Electrochemical Immunoassay for Insulin Based on Cu7S4-Au as a Double Signal Indicator

The detection of insulin by electrochemical (EC) immunoassay is desirable but highly challenged due to the obstacle of improving its accuracy, especially in a single-response system. In this work, based on Cu₇S₄-Au as a dual signal indicator, we fabricated a dual-mode electrochemical immunoassay for insulin. Especially, Cu₇S₄ presents a strong differential pulse voltammetry (DPV) signal for the electron transfer between Cu²⁺ and Cu⁺, without the addition of K₃[Fe(CN)₆] or other electron transfer mediators. Furthermore, Cu₇S₄ displays high sensitivity and high electrocatalytic activity toward the reduction of H₂O₂ through chronoamperometry (CA). The introduction of Au nanoparticles can not only link on the surface of Cu₇S₄ by the chemical bond of Au-SH, but also connect the second antibody (Ab₂) by the chemical bond of Au-N. Due to the superior electroconductivity of Au nanoparticles and the synergistic effect between the Au nanoparticles and Cu₇S₄, a high sensitivity is achieved by means of DPV and CA. To improve the loading capacity of antibodies, nanofiber polyaniline covalently grafted graphene (GS-PANI) linked with Au nanoparticles (GS-PANI-Au) as the matrix material was prepared. Based on Cu₇S₄-Au as a double signal indicator, the developed EC immunoassay for insulin exhibits a wide linear response for insulin detection in the range from 0.1 pg/mL to 50 ng/mL, with a low detection limit of 35.8 and 12.4 fg/mL through DPV and CA modes, respectively. Furthermore, the immunosensor displays an excellent analytical capability for insulin and promises application in quantitative detection of other disease markers in clinical diagnosis.