Application of calcium peroxide in water and soil treatment: A review

Remediation of surface water contaminated by pathogenic microorganisms using calcium peroxide: Matrix effect, micro-mechanisms and morphological-physiological changes

Calcium peroxide (CaO₂), a common solid peroxide, has been increasingly used in contaminated site remediation due to its ability to release oxygen (O₂) and hydrogen peroxide (H₂O₂) and its environmental friendliness. Our present study is first to explore micromechnisms of CaO₂ to efficaciously inactivate pathogen indicators including gram-negative bacterium of Escherichia coli (E. coli), gram-positive bacterium of Staphylococcus aureus (S. aureus), and virus of Escherichia coli-specific M13 bacteriophage (VCSM13) under low concentration (≤ 4 mmol L^-1 (mM)). The inactivation mechanisms of E. coli, S. aureus (1 mmol L^-1 CaO₂) and VCSM13 (4 mmol L^-1) were mainly attributed to OH^- (32∼58%) and •OH (34∼42%), followed by H₂O₂ (13∼20%) and O₂^•- (10∼12%) generated from CaO₂, with the observed morphological and physiological-associated damages. Also, average steady-state concentrations of (OH^-, •OH, H₂O₂, and O₂^•-) and their reaction rate constants with E. coli and VCSM13 were determined. Accordingly, the micro-mechanism model of inactivation was established and validated, and the inactivation efficiency of the same order of magnitude of pathogen was predicted. Furthermore, during the common environmental factors, the copper ions was found to be promote CaO₂ inactivation of pathogens, and dissolved organic matter (DOM) fractions had a negative effect on CaO₂ inactivation. The present study explored the mechanisms of CaO₂ inactivation of pathogens in real surface water, laying the foundation for its potential use in the inactivation of water-borne microbial pathogens.

An optimized CaO2-functionalized alginate bead for simultaneous and efficient removal of phosphorous and harmful cyanobacteria

Simultaneous removal of phosphorus (P) and algae is important to mitigate eutrophication, however, it is rather challenging in remediation of harmful algal blooms (HABs)-contaminated water. In this study, a wet alginate bead functionalized by CaO₂ particle formed layer by layer was prepared with an in-situ method and optimized to remove phosphorous and inhibit algae growth. The stable H₂O₂ release with a concentration level of 0.06 mM was observed for a period of 26 d. The content of peroxy groups (-O-O-) in the optimal bead was 0.44 mmol·g^-1 through permanganate-based titration study. For solution with an initial phosphorous concentration of 10 mg·L^-1, the removal was around 97% in pH 3.0-10.0. XRD, SEM, and XPS studies and kinetic modelings showed that removal of phosphorus was mainly due to formation of insoluble Ca-P compounds in the bead. The CaO₂-functionalized bead inhibited algae growth with an effect lasting over 170 d, which was much better than liquid H₂O₂ and Ca(OH)₂ bead; the phosphorous removal with an efficiency of about 70% was simultaneously obtained. Furthermore, the bead demonstrated to be effective in removing algae in the realistic water from a reservoir. In summary, this study shows that the CaO₂-functionalized material is promising for simultaneous removal of phosphorous and management of HABs.

Silver Peroxide Nanoparticles for Combined Antibacterial Sonodynamic and Photothermal Therapy

Metal peroxide nanoparticles designed to elevate the oxidative stress are considered a promising nanotherapeutics in biomedical applications, including chemotherapy, photodynamic therapy, and bacterial disinfection. However, their lack of specificity towards the therapeutic target can cause toxic side effects to healthy tissues. Here, silver peroxide nanoparticles (Ag₂ O₂ NPs) capable of controlled reactive oxygen species (ROS) release are synthesized. The release of bactericidal Ag⁺ ions and ROS is strictly regulated by external stimuli of ultrasound (US) and near-infrared (NIR) light. In vitro and in vivo investigations show that the Ag₂ O₂ NPs present enhanced antibacterial and antibiofilm capabilities with a killing efficiency >99.9999% in 10 min, significantly accelerate multi-drug resistant Staphylococcus aureus infected skin wound closure with excellent cytocompatibility and hemocompatibility. This work not only provides the first paradigm for fabricating silver peroxide nanoparticle but also introduces a highly efficient noninvasive and safe therapeutic modality for combating bacterial infectious diseases.

Bubble-Assisted HIFU Ablation Enabled by Calcium Peroxide

High intensity focused ultrasound (HIFU), as one of the most advanced and preferred cancer treatment modes, has shown great promise due to its minimal invasiveness and irradiation-free feature. However, a...

Facile synthesis of Fe-modified lignin-based biochar for ultra-fast adsorption of methylene blue: Selective adsorption and mechanism studies

A novel Fe-modified lignin-based biochar (Fe-LB) was fabricated via a facile one-step carbonization method for methylene blue (MB) removal from wastewater. Fe-LB exhibited a high specific surface area (885.97 m²/g) and micropore volume (0.3203 m³/g), and demonstrated high affinity for MB with the maximum adsorption capacity of 2.7-fold by Fe-LB than LB. It was found that quick adsorption could be achieved in 15 min with the MB removal efficiency of 100% and adsorption capacity reached 200 mg/g. Selective adsorption studies indicated that Fe-LB preferentially adsorbed MB in high salt and multiple dye systems (binary, ternary, and quaternary) over a wide pH range from 2 to 12. The removal efficiency of CR was greatly improved due to the synergistic effect between MB and CR in the binary system. This work demonstrated that Fe-LB can effectively remove dye contaminants and possessed great potential in the treatment of MB polluted dye wastewater.

Environmental opportunities and challenges of utilizing unactivated calcium peroxide to treat soils co-contaminated with mixed chlorinated organic compounds

Calcium peroxide (CaO₂) has been proven to oxidize various organic pollutants when they exist as a single class of compounds. However, there is a lack of research on the potential of unactivated CaO₂ to treat mixed chlorinated organic pollutants in soils. This study examined the potential of CaO₂ in treating soils co-contaminated with p-dichlorobenzene (p-DCB) and p-chloromethane cresol (PCMC). The effects of CaO₂ dosage and treatment duration on the rate of degradation were investigated. Furthermore, the collateral effects of the treatment on treated soil characteristics were studied. The result showed that unactivated CaO₂ could oxidize mixed chlorinated organic compounds in wet soils. More than 69% of the pollutants in the wet soil were mineralized following 21 days of treatment with 3% (w/w) CaO₂. The hydroxyl radicals played a significant role in the degradation process among the other decomposition products of hydrogen peroxide. Following the oxidation process, the treated soil pH was increased due to the formation of calcium hydroxide. Soil organic matter, cation exchange capacity, soil organic carbon, total nitrogen, and certain soil enzyme activities of the treated soil were decreased. However, the collateral effects of the system on electrical conductivity, available phosphorus, and particle size distribution of the treated soil were not significant. Likewise, since no significant release of heavy metals was seen in the treated soil matrix, the likelihood of metal ions as co-pollutants after treatment was low. Therefore, CaO₂ can be a better alternative for treating industrial sites co-contaminated with chlorinated organic compounds.

Effectiveness of chelating agent-assisted Fenton-like processes on remediation of glucocorticoid-contaminated soil using chemical and biological assessment: performance comparison of CaO2 and H2O2

Glucocorticoids (GCs) have drawn great concern due to widespread contamination in the environment and application in treating COVID-19. Most studies on GC removal mainly focused on aquatic environment, while GC behaviors in soil were less mentioned. In this study, degradation of three selected GCs in soil has been investigated using citric acid (CA)-modified Fenton-like processes (H₂O₂/Fe(III)/CA and CaO₂/Fe(III)/CA treatments). The results showed that GCs in soil can be removed by modified Fenton-like processes (removal efficiency gt; 70% for 24 h). CaO₂/Fe(III)/CA was more efficient than H₂O₂/Fe(III)/CA at low oxidant dosage (< 0.28-0.69 mmol/g) for long treatment time (> 4 h). Besides the chemical assessment with GC removal, effects of Fenton-like processes were also evaluated by biological assessments with bacteria and plants. CaO₂/Fe(III)/CA was less harmful to the richness and diversity of microorganisms in soil compared to H₂O₂/Fe(III)/CA. Weaker phytotoxic effects were observed on GC-contaminated soil treated by CaO₂/Fe(III)/CA than H₂O₂/Fe(III)/CA. This study, therefore, recommends CaO₂-based treatments to remediate GC-contaminated soils.

Fabrication of H2O2 slow-releasing composites for simultaneous Microcystis mitigation and phosphate immobilization

Hydrogen peroxide (H₂O₂) is a widely accepted algicide in controlling cyanobacterial blooms. However, this method includes two disadvantages: 1) a low H₂O₂ concentration (<5 mg L^-1) is required; 2) H₂O₂-induced cell lysis causes phosphorus (P) contamination. To overcome the drawbacks, a H₂O₂ slow-releasing composite (HSRC) based on calcium peroxide (CaO₂) was fabricated to substitute liquid H₂O₂. According to the results, a higher CaO₂ dose increased H₂O₂ yield and releasing rate. H₂O₂ yield of 160 mg L^-1 CaO₂ in HSRC reached 32.9 mg L^-1 and its releasing rate was 0.407 h^-1. In addition, a higher temperature decreased H₂O₂ yield and increased H₂O₂-releasing rate. Besides, HSRC endowed with a remarkable ability to immobilize P. Higher CaO₂ dose, pH value, and temperature increased the rate of P immobilization. The highest rate was 0.185 h^-1, which occurred with 160 mg L^-1 CaO₂ in HSRC at 25 °C and pH 8.0. Toxicity assays showed that HSRC exerted sustaining oxidative stress on Microcystis aeruginosa. Accumulation of intracellular reactive oxygen species resulted in the disruption of enzymatic systems and inactivation of photosystem. Tracking the variations of cell growth and H₂O₂ concentration during HSRC treatments, it suggested that the lethal effect on Microcystis aeruginosa was achieved with a super-low H₂O₂ concentration (<0.3 mg L^-1). In addition, cell lysis did not cause a sudden rise in P concentration due to the P immobilization by HSRC. Therefore, HSRC successfully offsets the drawbacks of liquid H₂O₂ in mitigating cyanobacterial blooms. It may be a novel and promising algicide that not only kills cyanobacteria but also reduces eutrophication momentarily.

Solid Peroxy Compounds as Additives to Organic Waste for Reclamation of Post-Industrial Contaminated Soils

Solid peroxy compounds have been increasingly applied for the removal of organic pollution from contaminated groundwater and soil due to their ability to release oxygen and hydrogen peroxide. The influence of two solid peroxy compounds (sodium percarbonate, 2Na₂CO₃·3H₂O₂ and calcium peroxide, CaO₂) with poultry manure (PM) added to contaminated soil on the growth of the tested plants (Sinapis alba, Lepidium sativum L. and Sorghum bicolor L. Moench) and the quality of soil water leachates was investigated. A series of experiments involving the addition of CaO₂ and 2Na₂CO₃·3H₂O₂ at the dose of 0.075 g/g PM improved the growth of tested plants. The conducted study indicated that the use of peroxy compounds not only removed pathogens from livestock waste, but also improved the quality of plant growth. The calculated factors for the growth of roots (GFR) and growth of shoots (GFS) in soils treated with a mixture of peroxy compounds and PM were higher than in soils treated only with PM. The physicochemical analysis of soil water leachates indicated that solid peroxy compounds may be a promising alternative compared to the currently used hygienizing agent such as calcium hydroxide (Ca(OH)₂). Solid peroxy compounds increased the bioavailability of components necessary for proper seed germination and plant growth (N, P, K, Ca, Mg and S). In most of the studied cases, the obtained plant shoot and root growth rates were higher for soil mixtures containing organic waste deactivated by biocidal compounds, compared to soils that contained only poultry manure.

Calcium Peroxide Nanoparticles-Embedded Coatings on Anti-Inflammatory TiO2 Nanotubes for Bacteria Elimination and Inflammatory Environment Amelioration

Implant-associated bacterial infections significantly impair the integration between titanium and soft tissues. Traditional antibacterial modifications of titanium implants are able to eliminate bacteria, but the resulting pro-inflammatory reactions are usually ignored, which still poses potential risks to human bodies. Here, a dual drug-loading system on titanium has been developed via the adhesion of a catechol motif-modified methacrylated gelatin hydrogel onto TiO₂ nanotubes. Then synthesized CaO₂ nanoparticles (NPs) are embedded into the hydrogel, and interleukin-4 (IL-4) is loaded into the nanotubes to achieve both antibacterial and anti-inflammatory properties. The dual drug-loading system can eliminate Staphylococcus aureus (S. aureus) rapidly, attributed to the H₂ O₂ release from CaO₂ NPs. The potential cytotoxicity of CaO₂ NPs is also remarkably reduced after being embedded into the hydrogel. More importantly, with the gradual release of IL-4, the dual drug-loading system is capable of modulating pro-inflammatory reactions by inducing M2 phenotype polarization of macrophages. In a subcutaneous infection model, the S. aureus contamination is effectively resolved after 2 days, and the resulting pro-inflammatory reactions are also inhibited after 7 days. Finally, the damaged tissue is significantly recovered. Taken together, the dual drug-loading system exhibits great therapeutic potential in effectively killing pathogens and inhibiting the resulting pro-inflammatory reactions.

Enhanced-oxidation of sulfanilamide in groundwater using combination of calcium peroxide and pyrite

Fenton reaction using hydrogen peroxide (H₂O₂) has been widely applied to achieve the in-situ chemical oxidation of contaminated soil and groundwater. However, injecting and transporting H₂O₂ to a contaminated zone consumes the chemical through reactions with other substances and self-decomposition. Additionally, Fe(II), an activator for the Fenton reaction, scavenges hydroxyl radicals, greatly reducing its activity. Therefore, this study proposes a novel oxidation system combining calcium peroxide (CaO₂) and pyrite for the degradation of oxidizable contaminants in groundwater. CaO₂ is an oxygen releasing compound, and pyrite is a natural mineral that provides Fe(II). The individual applications of CaO₂ and pyrite cannot generate OH radicals and oxidize the target pollutant, sulfanilamide. However, the combination of pyrite and CaO₂ oxidized well sulfanilamide even in mild pH and 1.0 wt% of pyrite. Moreover, H₂O₂ and OH radicals are the dominant oxidants in the reaction. A speciation analysis shows the oxidation of pyrite in this combined system. Furthermore, this system oxidized 80% of 0.1 mM sulfanilamide, whereas only 30% was oxidized by conventional Fenton reaction, indicating that this combined system is effective and applicable to remediate groundwater. This study provides an alternative oxidation process to achieve in-situ chemical oxidation.

A review on percarbonate-based advanced oxidation processes for remediation of organic compounds in water

Sodium percarbonate (SPC) is considered a potential alternative to liquid hydrogen peroxide (H₂O₂) in organic compounds contaminated water/soil remediation due to its regularly, transportable, economical, and eco-friendly features. The solid state of SPC makes it more suitable to remediate actual soil and water with a milder H₂O₂ release rate. Apart from its good oxidative capacity, alkaline SPC can simultaneously remediate acidized solution and soil to the neutral condition. Conventionally, percarbonate-based advanced oxidation process (P-AOPs) system proceed through the catalysis under ultraviolet ray, transition metal ions (i.e., Fe²⁺, Fe³⁺, and V⁴⁺), and nanoscale zero-valent metals (iron, zinc, copper, and nickel). The hydroxyl radical (^•OH), superoxide radical (^•O₂^-), and carbonate radical anion (^•CO₃^-) generated from sodium percarbonate could attack the organic pollutant structure. In this review, we present the advances of P-AOPs in heterogeneous and homogeneous catalytic processes through a wide range of activation methods. This review aims to give an overview of the catalysis and application of P-AOPs for emerging contaminants degradation and act as a guideline of the field advances. Various activation methods of percarbonate are summarized, and the influence factors in the solution matrix such as pH, anions, and cations are thoroughly discussed. Moreover, this review helps to clarify the advantages and shortcomings of P-AOPs in current scientific progress and guide the future practical direction of P-AOPs in sustainable carbon catalysis and green chemistry.

Removal of a reactive dye from simulated textile wastewater by environmentally friendly oxidant calcium peroxide

In the present study, calcium peroxide (CaO2) was used separately for potential application as an environmentally friendly and low-cost oxidant for the removal of a textile dye ‘Reactive Black 5’ (RB5) from simulated textile wastewater containing auxiliary chemicals of textile production. The specific morphology, elemental analysis, particle size distribution, specific surface area, identification of crystalline phases and surface functional groups of the synthesized CaO2 were investigated by scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), laser diffraction (LD), Brunaure–Emmett–Teller method (BET), X-ray diffraction (XRD) and Fourier transmission infrared (FTIR), respectively. X-ray Diffraction analysis confirmed the synthesized oxidant as CaO2 with the tetragonal crystalline structure. The signal corresponded to a bending vibration of O–Ca–O was detected in the fingerprint region of the FTIR spectroscopy. The effects of various independent parameters such as contact time, pH, initial RB5 concentration and CaO2 dosage on decolorization were investigated. The results of the study showed that pH, initial dye concentration and the CaO2 amounts have significant effects on removal of the RB5. The optimum pH was determined 7 for the removal of RB5 by CaO2. 2.0 g CaO2 was found to be sufficient for the removal of 300 mg/L RB5 with 96.93% removal efficiency. Also 82.8% chemical oxygen demand (COD) removal efficiency from simulated textile wastewater (STW) was obtained by 2.0 g CaO2. The results of the present study showed that the CaO2 can be used as an environmentally friendly and low-cost oxidant for effective removal of reactive textile dyes.

Simultaneous oxidation and removal of arsenite by Fe(III)/CaO2 Fenton-like technology

Arsenite contaminated water is one of severe global environmental problems. It is challenging to treat As(III) pollution by a one-step technology. In this study, we developed a Fe(III)/CaO₂ Fenton-like technology for the treatment of As(III). The simultaneous oxidation of arsenite and removal of arsenic were achieved with efficiencies of nearly 100% and 95.8% respectively, which outperforms conventional technologies. It worked well in pH 3 to 9, and in the presence of cationic heavy metals, anions and humic acid. Moreover, the PO₄^3- inhibited the removal of As(III). •OH and ¹O₂ played the important roles in the oxidation of As(III). The Ca(II) derived from CaO₂ made a significant contribution to the oxidation and removal of As(III). The SEM and XPS studies confirmed that the formation of Ca-Fe nascent colloid caused the effective removal of arsenic. Our study demonstrates that the one-step Fe(III)/CaO₂ technology has a great potential for purification of the As(III)-contaminated water.

Cyclic reactions-mediated self-supply of H2O2 and O2 for cooperative chemodynamic/starvation cancer therapy

Hydroxyl radical (·OH)-mediated chemodynamic therapy (CDT) and glucose oxidase (GOx)-based starvation therapy (ST) are two emerging antitumor strategies, limited by acid/H₂O₂ deficiency and tumor hypoxia, respectively. Herein, we developed a liposomal nanoplatform co-delivering Fe(OH)₃-doped CaO₂ nanocomposites and GOx molecules for synergistic CDT/ST with a complementary effect. Based on Fenton reactions initiated by iron ions, CaO₂-supplied H₂O₂ could not only generate ·OH for H₂O₂-sufficient CDT, but also produce O₂ to promote the catalytic efficiency of GOx under hypoxia. In return, the enhanced ST generated gluconic acid and H₂O₂, further amplifying CDT. Through in vitro and in vivo experiments, we demonstrated that such a mutually reinforced modality based on the cyclic Fenton/starvation reactions provided a novel and potent anticancer mechanism for the effective treatment of hypoxic cancers.

Improving the Properties of Degraded Soils from Industrial Areas by Using Livestock Waste with Calcium Peroxide as a Green Oxidizer

Over the past years, the treatment and use of livestock waste has posed a significant problem in environmental engineering. This paper outlines a new approach to application of calcium peroxide (CaO₂) as a green oxidizer and microbiocidal agent in the treatment of poultry manure. It also presents the application of pretreated waste in improvement of degraded soils in industrial areas. The CCD (Central Composite Design) and RSM (Response Surface Methodology) were employed for optimizing the process parameters (CaO₂ concentration 1.6–8.4 wt %, temperature 5.2–38.8 °C and contact time 7–209 h). The analysis of variance (ANOVA) was used to analyze the experimental results, which indicated good fit of the approximated to the experimental data (R² = 0.8901, R²_adj = 0.8168). The amendment of CaO₂ in optimal conditions (8 wt % of CaO_2, temperature 22 °C and contact time 108 h) caused a decrease in bacteria Escherichia coli (E. coli) in poultry manure from 8.7 log₁₀ CFU/g to the acceptable level of 3 log₁₀ CFU/g. The application of pretreated livestock waste on degraded soils and the studies on germination and growth of grass seed mixture (Lollum perenne—Naki, Lollum perenne—Grilla, Poa pratensis—Oxford, Festuca rubbra—Relevant, Festuca rubbra—Adio and Festuca trachypylla—Fornito) showed that a dose of 0.08 g of CaO₂ per 1 gram of poultry manure induced higher yield of grass plants. The calculated indicators for growth of roots (GFR) and shoots (GFS) in soils treated with poultry manure were 10–20% lower compared to soils with amended CaO₂. The evidence from this study suggests that CaO₂ could be used as an environmentally friendly oxidizer and microbiocidal agent for livestock waste.

Solid peroxides in Fenton-like reactions at near neutral pHs: Superior performance of MgO2 on the accelerated reduction of ferric species

Fenton-like reactions at near neutral pHs are limited by the slow reduction of ferric species. Enhancing generation of from solid peroxides is a promising strategy to accelerate the rate-limiting step. Herein, the H₂O₂ release and Fenton-like reactions of four solid peroxides, MgO₂, CaO₂, ZnO₂ and urea hydrogen peroxide (UHP), were investigated. Results indicated that UHP can release H₂O₂ instantly and show a similar behavior as H₂O₂ in the Fenton-like reactions. MgO₂ released H₂O₂ quickly in phosphate buffered solutions, which was comparable to CaO₂ but faster than ZnO₂. Metal peroxides induced higher initial phenol degradation rates than UHP and H₂O₂ when the same theoretic H₂O₂ dosages and Fe(III)-EDTA were used. MgO₂ displayed a superior performance for phenol degradation at pH 5, resulting in more than 93% phenol reduction at 1.5 h. According to kinetic analyses, the generation rate of in the MgO₂ system was 18 and 3.4 times higher than those in ZnO₂ and CaO₂ systems, respectively. The addition of MgO₂ significantly promoted H₂O₂ based Fenton-like reactions by increasing production of , and the mixture of MgO₂ and H₂O₂ had an improved utilization efficiency of active oxygen than the MgO₂ system. The findings suggested the critical roles of metal peroxides in favoring Fenton-like reactions and inspired strategies to simultaneously accelerate Fenton-like reactions and improve utilization efficiency of active oxygen.

One-step removal of harmful algal blooms by dual-functional flocculant based on self-branched chitosan integrated with flotation function

Harmful algal blooms induce severe environmental problems. It is challenging to remove algae by the current available treatments involving complicate process and costly instruments. Here, we developed a CaO₂@PEG-loaded water-soluble self-branched chitosan (CP-SBC) system, which can remove algae from water in one-step without additional instrumentation. This approach utilizes a novel flocculant (self-branched chitosan) integrated with flotation function (induced by CaO₂@PEG). CP-SBC exhibited better flocculation performance than commercial flocculants, which is attributed to the enhanced bridging and sweeping effect of branched chitosan. CP-SBC demonstrated outstanding biocompatibility, which was verified by zebrafish test and algae activity test. CaO₂@PEG-loaded self-branched chitosan can serve as an "Air flotation system" to spontaneous float the flocs after flocculation by sustainably released O₂. Furthermore, CP-SBC can improve water quality through minimizing dissolved oxygen depletion and reducing total phosphorus concentrations.

Feasibility study on grouting material prepared from red mud and metallurgical wastewater based on synergistic theory

A new type of red mud/slag/wastewater-based geopolymeric grouts (RSW) was prepared to solve the problem of wastewater and red mud to environment and promoting the safe construction of geotechnical engineering. The applicability of RSW was investigated using different red mud, alkali activator and wastewater dosage. Fourier transform infrared spectrum (FTIR), X-ray diffraction (XRD), semi-calorimetry, Scanning electron microscope-energy dispersive spectrometer (SEM-EDS), and ²⁹Si Magic Angle Spinning (MAS) Nuclear Magnetic Resonance (NMR) were conducted to study the effect of wastewater on RSW. The results showed that wastewater has an accelerating effect on the geopolymerization process of RSW, the mechanical strength increased first and then decreased with the increment of wastewater dosage, the 28 d compressive strength of RSW was 30.2 MPa, which is higher than the cement-based grouts. The leaching of heavy metals were lower than 0.4 mg/L, which demonstrates that the RSW has a good immobilization effect on the heavy metals. The FTIR and SEM-EDS analysis results showed that the ions in wastewater could participated in the geopolymerization process and the hydrated products has a immobilization effect on the heavy metals. Overall, this contribution explores utilizing red mud and wastewater, and preparing high performance grouts for underground engineering.

Nitrogen-Doped Titanium Dioxide Mixed with Calcium Peroxide and Methylcellulose for Dental Bleaching under Visible Light Activation

The available tooth whitening products in the market contain high concentrations of hydrogen peroxide (H₂O₂) as an active ingredient. Therefore, in order to curb the high H₂O₂ concentration and instability of liquid H₂O₂, this study evaluated the efficacy and cytotoxicity of the bleaching gel composed of 10% calcium peroxide (CaO₂) and visible-light-activating nitrogen-doped titanium dioxide (N-TiO₂) with methyl cellulose as a thickener. Extracted bovine teeth were discolored using coffee and black tea stain solution and were divided into two groups (n = 6). Bleaching was performed thrice on each tooth specimen in both the groups, with one minute of visible light irradiation during each bleaching time. The CIELAB L*a*b* values were measured pre- and post-bleaching. The N-TiO₂ calcinated at 350 °C demonstrated a shift towards the visible light region by narrowing the band gap energy from 3.23 eV to 2.85 eV. The brightness (ΔL) and color difference (ΔE) increased as bleaching progressed each time in both the groups. ANOVA results showed that the number of bleaching significantly affected ΔE (p < 0.05). The formulated bleaching gel exhibits good biocompatibility and non-toxicity upon exposure to 3T3 cells. Our findings showed that CaO₂-based bleaching gel at neutral pH could be a stable, safe, and effective substitute for tooth whitening products currently available in the market.

Mitigating translocation of arsenic from rice field to soil pore solution by manipulating the redox conditions

Arsenic (As) is uptaken more readily by rice over wheat and barley. The exposure of As to humans being in the rice-consuming regions is a serious issue. Thus, an effective practice to reduce the translocation of As from soil to rice grain should be implemented. During a flooding period, the water layer greatly limits the transport of oxygen from atmosphere to soil, which provides favorable conditions for reduction of oxygen. The reduction of Fe in the soil during the flooding condition is closely related to the As mobility, which expedites the release of As to the soil pore solution and increases As uptake by rice plants. Therefore, the performance of oxygen releasing compounds (ORCs) was evaluated to lower the translocation of As from soil to soil solution. Specifically, in the simple system containing ORCs and water, the oxygen releasing capacity of ORCs was scrutinized. In addition, ORCs was applied to sea sand and arsenic bearing ferrihydrite to identify the contribution of ORCs to As and iron mobility. Especially, ORCs were introduced to the closed (completely mixed system) and open (static) systems to simulate the paddy soil environment. Introducing ORCs increased the DO in the aqueous phase, and CaO₂ was more effective in increasing DO than MgO₂. In the static system simulating a rice field, the dissolution of ORCs was inhibited. The pH increased due to the formation of hydroxide, but the increase was not significant in the soil due to the buffering capacity of the soil. Finally, the As concentration in the soil solution was lowered to 25-50% of that of the control system by application of ORCs in the static paddy soil system. All experimental findings signify that the application of ORCs can be an effective practice to lower the translocation of As from soil to pore solution.

Promoted oxidation of polycyclic aromatic hydrocarbons in soils by dual persulfate/calcium peroxide system

In situ chemical oxidations (ISCO) have been demonstrated as effective ways for remediating soils contaminated with organic pollutants by complete mineralization. This work aims to develop a technology for the oxidation remediation of soils contaminated with Polycyclic Aromatic Hydrocarbons (PAHs) using a dual calcium peroxide (CP)/persulfate (PS) oxidant system activated by oxalic acid (OA)-chelating Fe²⁺. The dual peroxide system was set up, and the effects of 5 single factors (i.e., CP dosage, PS dosage, Fe²⁺ dosage, OA concentration, and soil/water ratio) on PAHs degradation were studied using the single-factor experiment. The response surface method was then introduced to obtain the optimized experimental conditions (CP dosage, PS dosage, OA concentration) of the dual peroxide system. The result shows that the dual peroxide system significantly increased the PAHs degradation and the maximum PAHs degradation efficiency (70.8%) was achieved by the dual peroxide system under optimal conditions (PS dosage, CP concentration, Fe²⁺/PS ratio, and Fe²⁺/OA ratio was 8.89 g/kg, 0.18 mol/L, 1/4 and 0.62) at neutral soil condition. This study is an illustration of the promising efficiency of the dual peroxide system for PAH oxidation in the neutral soil and has great potential for remediation of PAHs contaminated farmland soils.

Pretreatment using UV combined with CaO2 for the anaerobic digestion of waste activated sludge: Mechanistic modeling for attenuation of trace organic contaminants

Trace organic contaminants (TOrCs) in waste active sludge (WAS) have caused many concerns due to their recalcitrance and detriment to the performance of anaerobic digestion (AD). In this study, UV (2 h) combined with calcium peroxide (CaO₂, 0.1 g g^-1-VSS (VSS, volatile suspended solid) was proposed as a suitable sludge pretreatment to enhance the AD performance with an increase in the production of maximum total short-chain fatty acids (421.3 %) and methane (119.2 %). Meanwhile, above 50 % removal efficiency for 19 detected TOrCs was achieved. UV and CaO₂ had a synergistic effect on the subsequent AD of WAS. Both UV and Ca(OH)₂ produced by CaO₂ played important roles in the dissolution of WAS and the subsequent AD, while UV-direct and OH-indirect photolysis accounted for TOrCs attenuation. In order to predict TOrCs attenuation by UV/CaO₂ treatment, a TOrCs photolysis model was tentatively established using carbamazepine as an indicator. This predictive model expressed a good prediction with adj-R² = 0.94, and the difference of predicted and measured values was within 27.3 %. This work evaluates a sludge pretreatment for simultaneously TOrCs attenuation and methane accumulation, laying foundation for promotion of sludge resource recycling.

Effects of solid oxygen fertilizers and biochars on nitrous oxide production from agricultural soils in Florida

Elevated levels of nitrous oxide (N₂O) emissions are a matter of concern in agricultural soils especially when flooding (hypoxic conditions) results from over irrigation or frequent rains. This study is the first to report the use of two solid oxygen fertilizers (SOFs, calcium peroxide and magnesium peroxide) to reduce N₂O production in mineral and organic soils amended with N fertilizer in a short-term laboratory incubation besides two biochars. In general, organic soil had greater N₂O production than mineral soil. Soils amended with nitrogen fertilizer exhibited increased N₂O production, by 74 times in mineral soil and 2 times in organic soil. Both solid oxygen fertilizers in mineral soil (98–99%) and calcium peroxide in organic soil (25%) successfully reduced N₂O production than corresponding N fertilized treatments. Additionally, a greater level of available nitrate–N (52–57 and 225 mg kg⁻¹ in mineral and organic soil, respectively) was recorded with the solid oxygen fertilizers. Corn residue biochar with N fertilizer increased N₂O production in mineral soil but decreased in organic soil, while pine bark biochar with N did not affect the N₂O production in either soil. Depending on soil, appropriate SOFs applied were able to reduce N₂O production and maintain greater nitrate–N levels in flooded soil. Thus, solid oxygen fertilizers can potentially be used as an effective way to reduce N₂O emission from hypoxic soil in agricultural production systems.

Properties of CaO2 for H2O2 release and phosphate removal and its feasibility in controlling Microcystis blooms

Calcium peroxide (CP) has been widely applied in environmental remediation, but few studies have reported its application in controlling Microcystis blooms. To recognize its feasibility for mitigating Microcystis blooms, the properties of CP in terms of hydrogen peroxide (HP) release and phosphate removal were investigated at different CP doses, temperatures, and initial pH values. HP release kinetics followed the Higuchi model. Batch experiments conducted in this study suggested that the HP yield and release rate were positively correlated with the CP dose. Increasing temperature decreased the HP yield but accelerated the HP release rate. The phosphate removal kinetics were well simulated by the pseudo-second-order model. The batch experiments suggested that an increased CP dose enhanced the phosphate removal capacity, but it did not affect the phosphate removal rate. Moreover, increased temperature accelerated both phosphate removal capacity and rate. However, the initial pH of low-buffer-capacity solutions did not notably affect HP release and phosphate removal. According to laboratory experiments, HP released from CP could impair photosynthetic activity, resulting in Microcystis mortality. Furthermore, the reduced phosphate concentration in the solutions suggested that CP could facilitate the control of eutrophication, which directly reduced bloom formation. Hence, our results confirmed CP as a promising algicide for Microcystis bloom control, and it is worthwhile to develop novel methods for bloom mitigation based on CP. Graphic abstract.

Comparison of aniline removal by UV/CaO2 and UV/H2O2: Degradation kinetics and mechanism

The instability and rapid consumption of H₂O₂ limit the application of UV/H₂O₂ in water treatment. Recently, calcium peroxide (CaO₂) has been demonstrated as an effective source of H₂O₂. However, the performance and mechanism of UV/CaO₂ are still unknown. Herein, UV/CaO₂ and UV/H₂O₂ were compared for degradation of aniline. The removal efficiency of aniline by UV/CaO₂ was slightly lower than that by UV/H₂O₂, which could be attributed to the light scavenger by CaO₂ suspended particles. HO‧ was identified to participate in aniline degradation in both UV/CaO₂ and UV/H₂O₂, while O₂^-· was only involved in UV/CaO₂. The efficiency of aniline degradation in UV/CaO₂ was affected by the released H₂O₂ in the system. The release and decomposition rate of H₂O₂ in UV/CaO₂ system were influenced by the CaO₂ dosage and reaction pH, but slightly related with water matrix. Excessive CaO₂ would scavenge aniline degradation through the released H₂O₂ to react with HO‧. Acidic condition would enhance the concentration of H₂O₂ in UV/CaO₂ and promote the degradation of aniline. Cl^- showed slight and almost no effect on aniline degradation in UV/CaO₂ and UV/H₂O₂ systems, respectively, while HCO₃^- scavenged aniline degradation in UV/CaO₂. NO₃^- inhibited aniline degradation in both UV/CaO₂ and UV/H₂O₂. Compared to UV/H₂O₂, UV/CaO₂ shows the similar efficiency on organics removal but conquers the limitations in UV/H₂O₂, which is a promising alternative choice in water treatment.

Efficient transformation of diethyl phthalate using calcium peroxide activated by pyrite

In this study, pyrite (FeS₂) was used as a novel activator of calcium peroxide (CaO₂) for the degradation of diethyl phthalate (DEP) in both aqueous solution and soil. DEP (10 mg/L) in aqueous solution was completely degraded within 5.0 min by the FeS₂ (0.30 g/L)/CaO₂ (1.0 mM) system at pH 3.5. X-ray diffraction (XRD), scanning electron microscopy (SEM), electron paramagnetic resonance (EPR), free radical quenching, and X-ray photoelectron spectroscopy (XPS) were used to elucidate the mechanism of the catalytic decomposition of CaO₂, radical formation and DEP degradation in the presence of by pyrite. The results show that hydroxyl radicals (OH) are the dominant active species responsible for DEP degradation. Surface or lattice Fe(II) of FeS₂ readily activates H₂O₂ generated by CaO₂ decomposition to produce OH, while the reducing sulfur species of FeS₂ promotes the regeneration of surface of Fe(II) that catalyzes the production of additional OH, leading to the efficiently oxidative degradation of DEP. Although high concentration of common anions, such as Cl^-, NO₃^-, SO₄^2-, and HCO₃^-, exert inhibitory effects on DEP degradation by pyrite/CaO₂, the reaction system can still efficiently degrade DEP in realistic soil. It was observed that 78% of DEP (25 mg kg^-1) was degraded by 2.5% CaO₂ (w/w) and 0.5% FeS₂ (w/w) within 24 h. These results provide new insight into the mechanistic processes of CaO₂ activation and OH formation by the novel FeS₂ catalyst, demonstrating a promising alternative to the traditional H₂O₂-base Fenton process for contaminated soil remediation.

A novel magnesium-based oxygen releasing compound for eutrophic water remediation

Eutrophication of surface water bodies is a global problem in recent years. Dosing polluted water with oxygen releasing compounds (ORCs), especially those that can remove excessive nutrients simultaneously is regarded as one of the most economical and eco-friendly methods of treating eutrophic waters. In this study, a novel Mg-based ORC was synthesized and characterized as a magnesium hydroxide and hydrogen peroxide complex (MHHPC) with Mg to H₂O₂ ratio of 2:1. Oxygen-releasing, pH-adjusting and nutrient-removal potentials of MHHPC were evaluated in nano-pure and eutrophic water. The overall performance of MHHPC in preventing the eutrophic water from turning black and odorous was compared with the performance of other ORCs namely, MgO₂, CaO₂ and the combination of MgCl₂ and H₂O₂. The results showed that MHHPC was capable of constantly releasing oxygen to aqueous phase over a period of one week. Phosphate and ammonia nitrogen in synthetic buffered water can were removed as struvite and other precipitates from the aqueous phase. In the synthetic eutrophic water, all the ORCs tested were able to reduce aqueous ammonia nitrogen below 0.5 mM, while only CaO₂ and MHHPC successfully removed the aqueous phosphate. However, CaO₂ and MgCl₂+H₂O₂ significantly inhibited microbial activity.

The effect of microenvironment in the sediment on phosphorus immobilization under capping with ACPM and Phoslock®

Currently, in situ capping is a typical popular geoengineering method for eutrophication control. It is crucial to better understand the effect of microenvironment change due to capping, such as amended calcium peroxide material (ACPM) and Phoslock®, on phosphorus (P) adsorption and immobilization under the addition of external P. The microenvironment in sediment was presented by the concentration of O₂, NH₄⁺, and Fe²⁺ and microbial activity. The P removal and immobilization were also analyzed. The results show that the stronger oxidation in the microenvironment under the capping with ACPM was due to the higher reduction of NH₄⁺ and Fe²⁺ and the higher increase of microbial activity, compared to Phoslock®. Although, under the capping of ACPM, less amount of external P was removed and there was a faster release of sedimentary P, compared to Phoslock®, ACPM improved the transformation of P from mobile P fractions to inert P fractions. In addition, sedimentary P under the capping of ACPM presents less release than that under the capping of Phoslock® during the anaerobic incubation. However, the settlement of suspended solids decreased the function of capping. All these results indicated that the mechanism of P removal and immobilization was different under the capping of ACPM and Phoslock®.

Enhanced phosphate removal from aqueous solution using resourceable nano-CaO2/BC composite: Behaviors and mechanisms

The situation of eutrophication and shortage of phosphorus resources have triggered the development of new methods for the removal and recovery of phosphorus. In this study, a novel and highly efficient composite (nano-CaO₂/BC) was fabricated by using the porous biochar (BC) to load calcium peroxide (CaO₂) nanoparticles. The developed nano-CaO₂/BC was applied to remove and recover phosphate from P-contained sewage. The phosphate removal performance of the composite was examined using the bulk solutions with different pH values, coexisting anions, composite dosages, and initial phosphate concentrations. The phosphate adsorption was a typical chemisorption process that agreed well with the pseudo-second-order kinetic model. Isotherm studies showed that the adsorption matched well with Langmuir-Freundlich and the maximum adsorption capacity at equilibrium was 213.22 ± 13.57 mg g^-1 (298 K). The characterization results demonstrated that the predominant adsorption mechanism was precipitation. Moreover, the composite had good reusability. The seedling growth test confirmed that the P-laden composite can be mixed with soil to promote the growth of seedlings. Therefore, the method of "cycle back to soil" of used composite provided a way of resource utilization and waste disposal.

Oxygen-releasing nanofibers for breathable bone tissue engineering application

Oxygen is a vital molecule for cell and tissue processes. Electrospun fibers have been extensively used as drug loading carriers due to possibility of well control over drug release with modulating fiber properties. However, they have not been used as depots for oxygen release. In the present study, an oxygen-releasing nanofibrous scaffold has been developed by electrospinning of polylactic acid/nano-calcium peroxide suspension with different polylactic acid concentrations (6.5 and 13% w/v). The electrospun fibers with calcium peroxide cargo provided oxygen content of 30–94 mmHg in a period of 14 days which lies well within the oxygen level of osseous tissue. The release profile of 13% polylactic acid fibers was different with that of 6.5% fibers with respects to the initial content of released oxygen and the release rate. Not only did 13% fibers supply oxygen with a slower rate, but also they resulted in a lower burst release of oxygen. Cell culture studies in hypoxia corroborated that 13% polylactic acid fibers better preserve cell viability comparing 6.5% counterparts as perceived by MTT assay. Moreover, they endowed more favored milieu for adherence, arrangement and migration of mesenchymal stem cells as confirmed by microscopy images. The oxygen-releasing fibers equally affected alkaline phosphatase, osteocalcin, and calcium deposition by mesenchymal stem cells most likely due to interplay between topographical and metabolic cues offered by 6.5 and 13% formulations.

Metagenomic characterization of the enhanced performance of anaerobic fermentation of waste activated sludge with CaO2 addition at ambient temperature: Fatty acid biosynthesis metabolic pathway and CAZymes

This study investigated the chemical and genetic mechanisms of anaerobic fermentation of waste activated sludge (WAS) with CaO₂ addition at ambient temperature. The microbial community structures, key microorganisms, functional profiles and related carbohydrate-active enzymes were further revealed according to metagenomic sequencing combining with 16S rRNA gene amplicon sequencing. Results showed that the prolonged period of alkaline condition generated from CaO₂ contributed significantly to the continuous destruction of WAS, and the oxidative environment caused by CaO₂ further enhanced flocs dissolution. This synergistic effect also significantly changed the microbial community. Oxidation contributed more than the alkaline condition to the decline of microbial diversity, while the effect of alkaline condition was greater than that of oxidation in the change of microbial community structure. The key enhanced genes associated with fatty acid biosynthesis pathways with CaO₂ addition were highlighted. Three kinds of high-abundance acetyl-CoA carboxylase genes and eleven kinds of synthetase, hydrolase, lyase and oxidoreductase genes promoted by CaO₂ were distributed throughout each branch of fatty acid biosynthesis pathway (ko00061). Moreover, carbohydrate binding modules (CBMs) and glycoside hydrolases (GHs) were the top two carbohydrate-active enzymes (CAZymes) improved by CaO₂ addition. CaO₂ can also effectively promote the function of lysozyme and the metabolism of several monosaccharides. This work provides a deep insight into the advantage of CaO₂ in promoting sludge solubilization and acidification at the genetic levels, thus expanding the application of CaO₂ in sludge treatment and resource recovery.

Use of Phosphatase and Dehydrogenase Activities in the Assessment of Calcium Peroxide and Citric Acid Effects in Soil Contaminated with Petrol

The objective of the study was to compare the effect of calcium peroxide and citric acid on the activity of acid phosphatase (ACP), alkaline phosphatase (ALP), and dehydrogenases (DHA) in uncontaminated soil and soil contaminated with petrol. The experiment was carried out on samples of loamy sand under laboratory conditions. Petrol was introduced to soil samples at a dose of 0 and 50 g·kg 1 DM, as well as calcium peroxide or citric acid at a dose of 0, 50, 100, or 150 mg·kg 1 DM. The humidity of the samples was brought to 60% maximum water holding capacity, and the samples were incubated at 20°C for 8 weeks. Enzyme activity was determined on days 1, 14, 28, and 56. The obtained results demonstrated that the addition of calcium peroxide and citric acid did not result in significant changes in the activity of the determined enzymes in uncontaminated soil. However, it was observed that the application of calcium peroxide, particularly at the dose of 150 mg·kg 1 DM, largely alleviated the impact of petrol on the enzymatic activity of the soil contaminated with petrol. Moreover, among the determined enzymes, the activity of DHA was found to be the best indicator of the effect of calcium peroxide on the soil ecosystem.

Peroxidases from an invasive Mesquite species for management and restoration of fertility of phenolic-contaminated soil

Phenolics drive the global economy, but they also pose threats to soil health and plant growth. Enzymes like peroxidase have the potential to remove the phenolic contaminants from the wastewater; however, their role in restoring soil health and improving plant growth has not yet been ascertained. We fractionated efficient peroxidases (MPx) from leaves of an invasive species of Mesquite, Prosopis juliflora, and demonstrated its superiority over horseradish peroxidase (HRP) in remediating phenol, 3-chlorophenol (3-CP), and a mixture of chlorophenols (CP-M), from contaminated soil. MPx removes phenolics over a broader range of pH (2.0-9.0) as compared with HRP (pH: 7.0-8.0). In soil, replacing H₂O₂ with CaO₂ further increases the phenolic removal efficiency of MPx (≥90% of phenol, ≥ 70% of 3-CP, and ≥90% of CP-M). MPx maintains ~4-fold higher phenolic removal efficiency than purified HRP even in soils with extremely high contaminant concentration (2 g phenolics/kg of soil), which is desirable for environmental applications of enzymes for remediation. MPx treatment restores soil biological processes as evident by key enzymes of soil fertility viz. Acid- and alkaline-phosphatases, urease, and soil dehydrogenase, and improves potential biochemical fertility index of soil contaminated with phenolics. MPx treatment also assists the Vigna mungo test plant to overcome toxicant stress and grow healthy in contaminated soils. Optimization of MPx for application in the field environment would help both in the restoration of phenolic-contaminated soils and the management of invasive Mesquite.

Dose effects of calcium peroxide on harmful gases emissions in the anoxic/anaerobic landscape water system

Large-area hypoxia of urban landscape water often causes the emissions of harmful gases in summer, which not only reduces its sensory effects, but also brings a potential threat to aquatic ecosystem and human health. This study explored the dose effects of calcium peroxide (CaO₂) on inhibiting harmful gases emissions and restoring the scenic effect (including visual sense and olfactory sense) of anoxic/anaerobic landscape water system. The results indicated that the emissions of H₂S, CO₂ and CH₄ from the anoxic/anaerobic water system were obviously inhibited in the reactors with CaO₂ additions and the effect was positively correlated with the CaO₂ dose. Meanwhile, the concentrations of total chemical oxygen demand (TCOD) and soluble sulfide (S^2-), and turbidity in the overlying water (the water-layer above the sediment-water interface) were also decreased in the reactors dosed with CaO₂. The reason was ascribed to the improvement of the anoxic/anaerobic condition in the water system and the increase of the species richness, bacteria count and aerobic microorganism abundance in sediment. Furthermore, 0.12 kg-CaO₂ m^-2-sediment was selected as the optimal dose, which was based on considering the inhibiting effect of the harmful gases emissions, comprehensive influence and costs. Compared with control check (CK, the reactor without adding CaO₂), the optimal dose of CaO₂ could reduce 75.10% CH₄, 81.02% CO₂ and 100% H₂S in gases, and decrease 81.52% S^2-, 42.85% TCOD and 84.01% turbidity in the overlying water. In conclusion, all the dosages of CaO₂ could improve the anoxic condition of water system and 0.12 kg-CaO₂ m^-2-sediment was the optimal dose in inhibiting harmful gases emissions, which could keep an excellent water quality in this simulation experiment. Therefore, this study may provide a feasible method and the optimal dose for inhibiting the emissions of harmful gases and restoring the scenic effect in the similar anoxic/anaerobic landscape water.

Impact of calcium peroxide dosage on the control of nutrients release from sediment in the anoxic landscape water

The anoxic and reductive aquatic environment is formed easily in summer due to the global warming, which may accelerate endogenous release. In this experiment, four different dosages of calcium peroxide (CaO₂) were adopted to study the control effects of nutrients release from the sediments in the simulated landscape waters. The results demonstrated that CaO₂ addition could effectively improve the physicochemical properties and microbial composition in sediments, and an obvious improvement was achieved with a larger dosage. It was observed that the surface sediments of experiment groups were oxidized to form a capping barrier between the sediment and overlying water, which might cut off the pollutant diffusion in sediment. Meanwhile, CaO₂ could decrease the nutrients concentration in water obviously, and the reduced effect was positively correlated with the CaO₂ dosage. Compared with the nutrients release fluxes in CK (105.89 mg-TN m^-2 day^-1, 106.48 mg-NH₄⁺-N m^-2 day^-1, 4.14 mg-TP m^-2 day^-1, and 4.30 mg-SRP m^-2 day^-1), the CaO₂ dosages of 0.12 and 0.18 kg m^-2 could entirely inhibit the nutrients release from sediment, and partially reduce the original pollutants in the overlying water. However, 0.18 kg m^-2 CaO₂ would cause a higher increase of pH value and NO₂^--N concentration, and bring potential risk to the aquatic ecosystem. Therefore, 0.12 kg-CaO₂ m^-2-sediment was selected as the optimal dosage by considering the control effect, economic cost, and potential risk comprehensively. In general, this study provided a quantitative usage method of CaO₂, which is convenient and effective to prevent or control the nutrients release from sediment caused by anoxic and reductive condition in summer.

Treatment of slaughterhouse wastewater by acid precipitation (H2SO4, HCl and HNO3) and oxidation (Ca(ClO)₂, H2O2 and CaO₂)

The treatment of slaughterhouse wastewater was investigated by both acid precipitations and by oxidation processes. Precipitation tests were developed using three acids (H₂SO₄, HCl and HNO₃) at different operating pH (1-6). A decrease of the precipitation pH led to an increase of the conductivity values of the supernatant. Precipitation processes allowed the removal of chemical oxygen demand (COD) (41-97%), turbidity (56-99%) and total phosphorus (27-56%). Total phenols were removed (15-96%) from pH ≥ 2, depending on the precipitation process. Generally, precipitation processes decreased the hydroxide and bicarbonates species. Additionally, three different oxidation processes were tested at different concentrations (1-15 g L^-1): Ca(ClO)₂, H₂O₂ and CaO₂. When Ca(ClO)₂ and CaO₂ were applied, an increase of the supernatant conductivity was achieved. COD removal ≥71% and turbidity elimination in the range of 85-100% were achieved by using oxidation processes. CaO₂ was very effective to remove total phosphorus (81-96%). The increase of the oxidant concentration in H₂O₂ and Ca(ClO)₂ oxidation processes led to a decrease in the removal of total phenols and bicarbonates species. Optical density of the microorganism cultures was efficiently eliminated (up to 100%) by oxidation processes. In addition, acid precipitation and oxidation allowed to remove total solids (TS), total volatile solids (TVS), total suspended solids (TSS), ammonia nitrogen, nitrates and biochemical oxygen demand (BOD₅). Acid precipitation and oxidation produced sludge rich in organic matter and nutrients (Ca, Mg, P, Cl, Na and K). Despite the high removal efficiencies, a post-treatment following the precipitation and oxidation processes can be required.

Attenuation of pharmaceutically active compounds in aqueous solution by UV/CaO2 process: Influencing factors, degradation mechanism and pathways

As freshwater sources continue to be influenced by wastewater effluents, there is a dire need to develop advanced water treatment processes capable of treating the wastewater-derived contaminants, especially for pharmaceutically active compounds (PhACs). Ultraviolet light (UV) combined with calcium peroxide (CaO₂) as an advanced oxidation process (AOP) to attenuate five widespread PhACs (carbamazepine (CBZ), primidone (PMD), phenobarbital (PBB), thiamphenicol (TAP) and florfenicol (FF)) was investigated in this paper. The degradation of these compounds followed pseudo-first-order kinetics (R² > 0.96). The optimum CaO₂ dosage was 0.1 g L^-1 and lower initial contaminants concentration was beneficial to their degradation. The UV/CaO₂ treatment of test PhACs was attributed to the combination of UV/H₂O₂ and UV-base-photolysis (UV/Ca(OH)₂), and the degradation mechanism was recognized as both UV direct photolysis and indirect photolysis caused by reactive radicals (•OH, triplet states of dissolved organic matter (³DOM*), and ¹O₂). Furthermore, the tentative transformation pathways of the five PhACs were proposed based on the detected intermediates and the degradation mechanisms. The final products of inorganic carbon and nitrogen indicate UV/CaO₂ treatment can significantly mineralize test PhACs. Also, the CaO₂ addition significantly reduced the energy consumption of UV irradiation according to electrical energy per order. The effective removal of CBZ and PMD in a secondary wastewater effluent by UV/CaO₂ treatment demonstrates the potential use of this AOP technology in advanced treatment of wastewater-derived PhACs.

Shift of Sediments Bacterial Community in the Black-Odor Urban River during In Situ Remediation by Comprehensive Measures

The phenomenon of black-odor urban rivers with rapid urbanization has attracted extensive attention. In this study, we investigated the water quality and composition of sediment-associated bacteria communities in three remediation stages (before remediation, 30 days after remediation, and 90 days after remediation) based on the in situ remediation using comprehensive measures (physical, chemical, and biological measures). The results show that the overlying water quality was notably improved after in situ remediation, while the diversity and richness of sediment-associated bacterial communities decreased. A growing trend of some dominant genus was observed following the remediation of a black-odor river, such as Halomonas, Pseudomonas, Decarbonamis, Leptolina, Longilina, Caldiseericum, Smithella, Mesotoga, Truepera, and Ralstonia, which play an important role in the removal of nitrogen, organic pollutants and hydrogen sulfide (H2S) during the sediment remediation. Redundancy analysis (RDA) showed that the bacterial community succession may accelerate the transformation of organic pollutants into inorganic salts in the sediment after in situ remediation. In a word, the water quality of the black-odor river was obviously improved after in situ remediation, and the bacterial community in the sediment notably changed, which determines the nutrients environment in the sediment.

Sustainable modulation of anaerobic malodorous black water: The interactive effect of oxygen-loaded porous material and submerged macrophyte

Depleted oxygen (O₂) in the sediment and overlying water of malodorous black water poses a potential threat to aquatic ecosystems. This study presents a method for sustainable regulation of the dissolved oxygen (DO) levels towards the malodorous black water. Oxygen-loaded natural porous materials were prepared by vacuum degassing to remove air from the pores and fill them with pure O₂. Capping anaerobic sediment with the prepared 6 oxygen-loaded porous materials was effective in prompting the DO concentration of the malodorous black water. Although granules activated carbon (GAC) displayed the highest oxygen-loading capability, oxygen-loaded volcanic stone additive was more efficient for long-lasting combating of the anaerobic condition because the DO level at sediment-water interface (SWI) and the DO penetration depth showed approximately 5.38- and 3.75-fold increase, respectively, compared with the untreated systems. The improvement in DO was substantially enhanced in the presence of submerged macrophyte (Vallisneria natans), during which the release of O₂ from oxygen-loaded volcanic stone facilitated the plant growth. With the joint efforts of the O₂ released from volcanic stone and photosynthesis by the macrophytes, the DO levels were maintained at approximately 6.80 mg/L after a 41-day incubation, which exceeded (P < 0.05) the value in only oxygen-loaded volcanic stone or macrophytes added treatments. In addition to the elevated DO level, the combined employment of oxygen-loaded volcanic stone and macrophytes triggered a negative ammonia (NH₄⁺-N) flux across the SWI and an 85.82% reduction of methane (CH₄) production compared with those without treatment, accompanied by a decrease in total inorganic carbon and a 2.55- fold increasing of submerged macrophyte biomass, which is presumably attributed to nitrification, remineralization, and assimilation. The results obtained here shed a degree of light on the sustainable modulation of the anaerobic condition in malodorous black water.

Bioremediation of benzene-contaminated groundwater by calcium peroxide (CaO2) nanoparticles: Continuous-flow and biodiversity studies

Calcium peroxide (CaO₂) nanoparticles have been extensively applied in treatment of contaminated groundwater through bioremediation or modified Fenton (MF) processes. In the present study utilization of CaO₂ in bioremediation and MF (CaO₂+FeSO₄) reaction is investigated for benzene (50 mg/L) removal in continuous flow sand-packed columns. The results indicated that MF produced OH radicals markedly increased benzene remediation at first 30 days (up to 93%). But, OH generation rate was gradually declined when the pH was increased and finally 75% of initial benzene removed after 100d. In bioremediation column, because of supplying adequate oxygen by CaO₂, the number of planktonic bacteria logarithmically increased to more than 5 × 10⁶ CFU/mL (two orders of magnitude) and consequently 100% benzene removal was achieved by the end of experiment. Scanning electron microscopy analysis visualized the attached biofilm growth on sand surfaces in CaO₂ injected columns indicating their key role in the remediation process. The impact of each process on the microbial biodiversity of groundwater was investigated by next generation sequencing (NGS) of the 16S rRNA gene. The alpha and beta analysis indicated that microbial diversity is decreased by CaO₂ injection while benzene-degrading species such as Silanimonas, Arthrobacter and Pseudomonas spp. were dominated in remediation column.

Effect of calcium peroxide on the water quality and bacterium community of sediment in black-odor water

This study investigated how efficiently CaO₂ could treat black-odor landscape water caused by low dissolved oxygen (DO) in a field experiment of 600 m². The study demonstrated that CaO₂ could significantly elevate the DO concentration in waters and the oxidation-reduction potential (ORP) level in sediments (p = 0.003 and p = 0), which is conducive to improving the anoxic environment of landscape water. The concentrations of total chemical oxygen demand (TCOD) and S^2- in overlying and interstitial waters were considerably decreased. The average concentrations of TCOD in the overlying and interstitial waters of the test zone (TZ) were 52.98% and 66.05% of those of the control zone (CZ), and the average concentrations of S^2- in the overlying and interstitial waters of TZ were 29.63% and 39.79% of those of CZ. Meanwhile, CaO₂ could obviously reduce turbidity but increase the transparency in the overlying water. The mean value of turbidity in the overlying water of TZ was 39.46% of that of CZ, whereas the transparency in the overlying water of TZ was 2.07 times that of CZ. Furthermore, CaO₂ changed the microbial community structure in the sediments, where the relative abundance of anaerobic bacteria was decreased but that of the aerobic bacteria was increased with some functional bacteria. In summary, CaO₂ could significantly increase the DO and ORP in black-odor landscape water, obviously inhibit the release of pollutants from sediment, and increase the diversity of microbial strains. Consequently, the black-odor phenomenon of landscape water could be alleviated effectively by adding CaO₂.

Insight into CaO2-based Fenton and Fenton-like systems: strategy for CaO2-based oxidation of organic contaminants

This study conducted a comparison of the CaO₂-based Fenton (CaO₂/Fe(II)) and Fenton-like (CaO₂/Fe(III)) systems on their benzene degradation performance. The H₂O₂, Fe(II), Fe(III), and HO^● variations were investigated during the benzene degradation. Although benzene has been totally removed in the two systems, the variation patterns of the investigated parameters were different, leading to the different benzene degradation patterns. In terms of the Fe(II)/Fe(III) conversion, the CaO₂/Fe(II) and CaO₂/Fe(III) systems were actually inseparable and had the inherent mechanism relationships. For the CaO₂/Fe(III) system, the initial Fe(III) must be converted to Fe(II), and then the consequent Fenton reaction could be later developed with the regenerated Fe(II). Moreover, some benzene degradation intermediates could have the ability to facilitate the transformation of the Fe(III) to Fe(II) without the classic H₂O₂-associated propagation reactions. By varying the Fe(II) dosing method, an effective degradation strategy has been developed to take advantage of the two CaO₂-based oxidation systems. The proposed strategy was further successfully tested in TCE degradation, therefore extending the potential for the application of this technique.