Tafel Kinetics of Electrocatalytic Reactions: From Experiment to First-Principles

Unveiling the Coercivity-Induced Electrocatalytic Oxygen Evolution Activity of Single-Domain CoFe2O4 Nanocrystals under a Magnetic Field

Spin polarization modulation in ferromagnetic materials has become an effective way to promote the electrocatalytic oxygen evolution reaction (OER). Herein, to reveal the coercivity-related OER performance, single-domain ferromagnetic CoFe₂O₄ (CFO) nanocrystals with different coercivities are synthesized and subjected to OER under an in situ tunable magnetic field. As the more ordered spin polarization state of CFO with a higher coercivity can afford a facilitated electron transfer process, the magnetic field-assisted OER activity can be more improved with an increase in coercivity. Specifically, the decreased magnitudes of the overpotential, Tafel slope, and charge transfer resistance increase on the samples with higher coercivity. The CFO with the largest coercivity (7500 Oe) shows the best OER performance with an overpotential of 350 mV at a current density of 10 mA cm^-2 under a magnetic field of 14000 G. In addition, a hysteresis effect that maintains enhanced OER current density after the magnetic field has been withdrawn is observed, where higher coercivity affords a longer hysteresis period. The exploration of coercivity-related OER enhancement may provide new insights into the design and synthesis of promising "magnetic effect" catalysts.

Low Platinum-Loaded Molybdenum Co-catalyst for the Hydrogen Evolution Reaction in Alkaline and Acidic Media

Developing an efficient catalytic system for electrolysis with reduced platinum (Pt) loading while maintaining performance comparable to bulk platinum metal is important to decrease costs and improve scalability of the hydrogen fuel economy. Here we report the performance of a novel sputter-deposited molybdenum (Mo) thin film with an extremely low co-loading of Pt, where Pt atoms were dispersed on Mo (Pt_d-Mo) as an electrocatalyst for the hydrogen evolution reaction (HER) in either alkaline or acidic media. The Pt_d-Mo electrocatalyst presents similar catalytic activity to bulk Pt in alkaline media, while the performance is only slightly decreased in acidic media. Differential electrochemical mass spectrometry (DEMS) results confirm that the Pt_d-Mo electrocatalyst produced hydrogen at a rate comparable with that of a pristine Pt sample at the same potential. A comparison with Pt-loaded degenerately doped p-type doped silicon (Pt_d-Si) suggests that Mo and Pt work synergistically to boost the performance of Pt_d-Mo catalysts. Cyclic voltammetry (CV) and X-ray photoelectron spectroscopy (XPS) before and after 1000 cycles of continuous operation confirm the significant durability of the Pt_d-Mo performance. Overall, the Pt_d-Mo electrocatalyst, with comparable HER activity to bulk Pt despite an ultra-low Pt loading, could be a strong candidate for hydrogen production in either acidic or basic conditions.

Efficient Electrocatalyst Nanoparticles from Upcycled Class II Capacitors

To move away from fossil fuels, the electrochemical reaction plays a critical role in renewable energy sources and devices. The anodic oxygen evolution reaction (OER) is always coupled with these reactions in devices but suffers from large energy barriers. Thus, it is important for developing efficient OER catalysts with low overpotential. On the other hand, there are large amounts of metals in electronic waste (E-waste), especially various transition metals that are promising alternatives for catalyzing OER. Hence, this work, which focuses on upcycling Class II BaTiO₃ Multilayer Ceramic Capacitors, of which two trillion were produced in 2011 alone. We achieved this by first using a green solvent extraction method that combined the ionic liquid Aliquat^® 336 and hydrochloride acid to recover a mixed solution of Ni, Fe and Cu cations, and then using such a solution to synthesize high potential catalysts NiFe hydroxide and NiCu hydroxide for OER. NiFe-hydroxide has been demonstrated to have faster OER kinetics than the NiCu-hydroxide and commercial c-RuO₂. In addition, it showed promising results after the chronopotentiometry tests that outperform c-RuO₂.

Application of machine-learning-based global optimization: potential-dependent co-electrosorbed structure and activity on the Pd(110) surface

Electrodes can adsorb different reaction intermediates under electrochemical conditions, which in turn significantly affect their electrochemical performance. This complex phenomenon attracts continuous interest in both science and industry for understanding the co-electrosorbed structure and activity under electrochemical conditions. Here, we report the first theoretical attempt by combining the machine-learning-based global optimization (SSW-NN method) and modified Poisson-Boltzmann continuum solvation (CM-MPB) based on first-principles calculations to elucidate the potential-dependent co-electrosorbed species on the Pd(110) surface. We reveal the potential-dependence adsorption/absorption hydrogen phases, the phase transition of α-H_ri/Pd to β-H_ri/Pd, and the co-electrosorbed H_ri-NH_y surface structures. In particular, we found that H_ri-NH₂ and H_ri-NH₃ are favorable intermediates for the N₂ reduction reaction, and the subsurface H is the key species responsible for NH₂ hydrogenation on the Pd(110) electrode.

Rapid and Energetic Solid-State Metathesis Reactions for Iron, Cobalt, and Nickel Boride Formation and Their Investigation as Bifunctional Water Splitting Electrocatalysts

Metal borides have long-standing uses due to their desirable chemical and physical properties such as high melting points, hardness, electrical conductivity, and chemical stability. Typical metal boride preparations utilize high-energy and/or slow thermal heating processes. This report details a facile, solvent-free single-step synthesis of several crystalline metal monoborides containing earth-abundant transition metals. Rapid and exothermic self-propagating solid-state metathesis (SSM) reactions between metal halides and MgB₂ form crystalline FeB, CoB, and NiB in seconds without sustained external heating and with high isolated product yields (∼80%). The metal borides are formed using a well-studied MgB₂ precursor and compared to reactions using separate Mg and B reactants, which also produce self-propagating reactions and form crystalline metal borides. These SSM reactions are sufficiently exothermic to theoretically raise reaction temperatures to the boiling point of the MgCl₂ byproduct (1412 °C). The chemically robust monoborides were examined for their ability to perform electrocatalytic water oxidation and reduction. Crystalline CoB and NiB embedded on carbon wax electrodes exhibit moderate and stable bifunctional electrocatalytic water splitting activity, while FeB only shows appreciable hydrogen evolution activity. Analysis of catalyst particles after extended electrocatalytic experiments shows that the bulk crystalline metal borides remain intact during electrochemical water-splitting reactions though surface oxygen species may impact electrocatalytic activity.

One A3B Porphyrin Structure—Three Successful Applications

Porphyrins are versatile structures capable of acting in multiple ways. A mixed substituted A₃B porphyrin, 5-(3-hydroxy-phenyl)-10,15,20-tris-(3-methoxy-phenyl)-porphyrin and its Pt(II) complex, were synthesised and fully characterised by ¹H- and ¹³C-NMR, TLC, UV-Vis, FT-IR, fluorescence, AFM, TEM and SEM with EDX microscopy, both in organic solvents and in acidic mediums. The pure compounds were used, firstly, as sensitive materials for sensitive and selective optical and fluorescence detection of hydroquinone with the best results in the range 0.039–6.71 µM and a detection limit of 0.013 µM and, secondly, as corrosion inhibitors for carbon–steel (OL) in an acid medium giving a best performance of 88% in the case of coverings with Pt-porphyrin. Finally, the electrocatalytic activity for the hydrogen and oxygen evolution reactions (HER and OER) of the free-base and Pt-metalated A₃B porphyrins was evaluated in strong alkaline and acidic electrolyte solutions. The best results were obtained for the electrode modified with the metalated porphyrin, drop-casted on a graphite substrate from an N,N-dimethylformamide solution. In the strong acidic medium, the electrode displayed an HER overpotential of 108 mV, at i = −10 mA/cm² and a Tafel slope value of 205 mV/dec.

Catalyst Composites of Palladium and N-Doped Carbon Quantum Dots-Decorated Silica and Reduced Graphene Oxide for Enhancement of Direct Formic Acid Fuel Cells

Pd-based catalysts consisting of Pd nanoparticles on nitrogen-doped carbon quantum dots (N-CQDs) modified silica (SiO₂) and reduced graphene oxide have been synthesized through reduction for use as catalysts for improved formic acid oxidation. The structure, morphology, chemical composition, functional groups, and porosity of the synthesized catalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FT-IR) spectroscopy, Raman spectroscopy, and Brunauer-Emmett-Teller (BET) spectroscopy, respectively. Their electrocatalytic activities were also evaluated by electrochemical measurements. The differences in the average particle sizes found for Pd/N-CQDs-SiO₂-rGO, Pd/N-CQDs-rGO, and Pd/rGO were 4.81, 5.56, and 6.31 nm, respectively. It was also found that the Pd/xN-CQDs-SiO₂-yrGO composite catalysts (where x and y is 1 to 4) can significantly improve the activity and stability toward formic acid electrooxidation compared with Pd/rGO and commercial Pt/C. The mass activities of Pd/N-CQDs-SiO₂-rGO, Pd/N-CQDs-rGO, and Pd/rGO were 951.4, 607.8, and 157.6 mA g^-1, respectively, which was ca. 6-7 times compared with Pd/rGO and approximately 3-4 times compared with commercial Pt/C. With low potential for CO oxidation and high current intensity, the composites of rGO, SiO₂, and N-CQDs into Pd-based catalysts improved the catalytic activity of the prepared catalyst for the oxidation of formic acid in acidic media. The value of the Tafel slope designated that the chief path of the prepared catalysts is the dehydrogenation process. These prepared catalysts exhibit promise toward the development of high-performance Pd-based electrocatalysts for formic acid oxidation.

Controllable growth of Fe-doped NiS2 on NiFe-carbon nanofibers for boosting oxygen evolution reaction

The construction of high-efficiency and low-cost electrocatalysts toward oxygen evolution reaction (OER) to improve the overall water decomposition performance is a fascinating route to deal with the clean energy application. Herein, Fe-doped NiS₂ crystals grown on the surface of carbon nanofibers (CNFs) encapsulated with NiFe alloy nanoparticles ((Ni,Fe)S₂/NiFe-CNFs) are fabricated through an electrospinning-calcination-vulcanization process, which has been used as a splendid electrocatalyst for OER. Benefitting from the abundant electrochemical active sites from the incorporation of Fe element in NiS₂ and the synergistic effect between NiFe-CNFs and surface sulfides, the obtained (Ni,Fe)S₂/NiFe-CNFs catalyst exhibits highly electrochemical activities and satisfactory durability toward OER in an alkaline medium with a low overpotential of only 287 mV at a high current density of 30 mA cm^-2, and with a little decline in the current retention after 48 h, suggesting its superior OER performance even compared with some noble metal-based electrocatalysts. Additionally, a two-electrode system conducted by using the (Ni,Fe)S₂/NiFe-CNFs and commercial Pt/C as electrodes, only needs a cell voltage of 1.54 V to afford 10 mA cm^-2 for overall water splitting, which is even much better than the RuO₂||Pt/C electrolyzer. This study offers a promising approach to prepare high-efficiency OER catalysts toward overall water splitting.

Tafel Analysis Guided Optimization of ZnNP-O-C Catalysts for the Selective 2-Electron Oxygen Reduction Reaction in Neutral Media

The lack of characterizations of the adsorption capability toward intermediates during reactions causes difficulties in determining the structural optimization principle of the catalysts for the 2-electron oxygen reduction reaction (2e^- ORR). Here, a Tafel-θ method is proposed to evaluate the surface coverage (θ) of important intermediates (*OOH and *OH) on the material surface and further help optimize the catalyst. With the assistance of Tafel-θ analysis, a Zn nanoparticle incorporated oxygen-doped carbon (Zn_NP-O-C) catalyst with high 2e^- ORR performance (onset of ∼0.57 V and selectivity of >90.4%) in neutral media was achieved. Both the theoretical calculation and characterization results are consistent with the Tafel-θ deduction, revealing that an appropriate ratio of Zn nanoparticles and bridging O can optimize the *OOH adsorption/desorption strength of the adjacent carbon site. This study not only provides an advanced Zn_NP-O-C catalyst for electrochemical H₂O₂ production but also proposes a fast and precise method for the comprehensive assessment of future catalysts.

Anion-Exchange Membrane Water Electrolyzers

This Review provides an overview of the emerging concepts of catalysts, membranes, and membrane electrode assemblies (MEAs) for water electrolyzers with anion-exchange membranes (AEMs), also known as zero-gap alkaline water electrolyzers. Much of the recent progress is due to improvements in materials chemistry, MEA designs, and optimized operation conditions. Research on anion-exchange polymers (AEPs) has focused on the cationic head/backbone/side-chain structures and key properties such as ionic conductivity and alkaline stability. Several approaches, such as cross-linking, microphase, and organic/inorganic composites, have been proposed to improve the anion-exchange performance and the chemical and mechanical stability of AEMs. Numerous AEMs now exceed values of 0.1 S/cm (at 60–80 °C), although the stability specifically at temperatures exceeding 60 °C needs further enhancement. The oxygen evolution reaction (OER) is still a limiting factor. An analysis of thin-layer OER data suggests that NiFe-type catalysts have the highest activity. There is debate on the active-site mechanism of the NiFe catalysts, and their long-term stability needs to be understood. Addition of Co to NiFe increases the conductivity of these catalysts. The same analysis for the hydrogen evolution reaction (HER) shows carbon-supported Pt to be dominating, although PtNi alloys and clusters of Ni(OH)₂ on Pt show competitive activities. Recent advances in forming and embedding well-dispersed Ru nanoparticles on functionalized high-surface-area carbon supports show promising HER activities. However, the stability of these catalysts under actual AEMWE operating conditions needs to be proven. The field is advancing rapidly but could benefit through the adaptation of new in situ techniques, standardized evaluation protocols for AEMWE conditions, and innovative catalyst-structure designs. Nevertheless, single AEM water electrolyzer cells have been operated for several thousand hours at temperatures and current densities as high as 60 °C and 1 A/cm², respectively.

Ni-Directed biphase N-doped Mo2C as an efficient hydrogen evolution catalyst in both acidic and alkaline conditions

The development of efficient and low-cost catalysts is of great significance for the future application of the electrocatalytic hydrogen evolution reaction (HER). Herein, a series of Ni,N co-doped Mo₂C nanostructures (Ni_x-Mo₂C/N) with different Ni content levels are fabricated. The phase-directing effect of Ni on Mo₂C/N is observed, which is in charge of the phase transformation of Mo₂C/N from an α- to a β-phase. At the optimized Ni-doping level, biphase Ni₁₅-Mo₂C/N exhibits outstanding HER activity under both acidic and alkaline conditions. In particular, under alkaline conditions, Ni₁₅-Mo₂C/N delivers an overpotential of only 105.0 mV, accompanied by a low Tafel slope of 44.96 mV dec^-1. The performance is comparable to commercial 20% Pt/C and higher than most state-of-the-art Mo₂C-based catalysts as well.

Co-Ni Layered Double Hydroxide for the Electrocatalytic Oxidation of Organic Molecules: An Approach to Lowering the Overall Cell Voltage for the Water Splitting Process

Electrocatalytic oxidation of simple organic molecules offers a promising strategy to combat the sluggish kinetics of the water oxidation reaction (WOR). The low potential requirement, inhibition of the crossover of gases, and formation of value-added products at the anode are benefits of the electrocatalytic oxidation of organic molecules. Herein, we developed cobalt-nickel-based layered double hydroxide (LDH) as a robust material for the electrocatalytic oxidation of alcohols and urea at the anode, replacing the WOR. A facile synthesis protocol to form LDHs with different ratios of Co and Ni is adapted. It demonstrates that the reactants could be efficiently oxidized to concomitant chemical products at the anode. The half-cell study shows an onset potential of 1.30 V for benzyl alcohol oxidation reaction (BAOR), 1.36 V for glycerol oxidation reaction (GOR), 1.33 V for ethanol oxidation reaction (EOR), and 1.32 V for urea oxidation reaction (UOR) compared with 1.53 V for WOR. Notably, the hybrid electrolyzer in a full-cell configuration significantly reduces the overall cell voltage at a 20 mA cm^-2 current density by ∼15% while coupling with the BAOR, EOR, and GOR and ∼12% with the UOR as the anodic half-cell reaction. Furthermore, the efficiency of hydrogen generation remains unhampered with the types of oxidation reactions (alcohols and urea) occurring at the anode. This work demonstrates the prospects of lowering the overall cell voltage in the case of a water electrolyzer by integrating the hydrogen evolution reaction with suitable organic molecule oxidation.

Conversion of Catalytically Inert 2D Bismuth Oxide Nanosheets for Effective Electrochemical Hydrogen Evolution Reaction Catalysis via Oxygen Vacancy Concentration Modulation

Oxygen vacancies (V_o) in electrocatalysts are closely correlated with the hydrogen evolution reaction (HER) activity. The role of vacancy defects and the effect of their concentration, however, yet remains unclear. Herein, Bi₂O₃, an unfavorable electrocatalyst for the HER due to a less than ideal hydrogen adsorption Gibbs free energy (ΔG_H*), is utilized as a perfect model to explore the function of V_o on HER performance. Through a facile plasma irradiation strategy, Bi₂O₃ nanosheets with different V_o concentrations are fabricated to evaluate the influence of defects on the HER process. Unexpectedly, while the generated oxygen vacancies contribute to the enhanced HER performance, higher V_o concentrations beyond a saturation value result in a significant drop in HER activity. By tunning the V_o concentration in the Bi₂O₃ nanosheets via adjusting the treatment time, the Bi₂O₃ catalyst with an optimized oxygen vacancy concentration and detectable charge carrier concentration of 1.52 × 10²⁴ cm^-3 demonstrates enhanced HER performance with an overpotential of 174.2 mV to reach 10 mA cm^-2, a Tafel slope of 80 mV dec^-1, and an exchange current density of 316 mA cm^-2 in an alkaline solution, which approaches the top-tier activity among Bi-based HER electrocatalysts. Density-functional theory calculations confirm the preferred adsorption of H* onto Bi₂O₃ as a function of oxygen chemical potential (∆μ_O) and oxygen partial potential (P_O2) and reveal that high V_o concentrations result in excessive stability of adsorbed hydrogen and hence the inferior HER activity. This study reveals the oxygen vacancy concentration-HER catalytic activity relationship and provides insights into activating catalytically inert materials into highly efficient electrocatalysts.

A tetra Co(II/III) complex with an open cubane Co4O4 core and square-pyramidal Co(II) and octahedral Co(III) centres: bifunctional electrocatalytic activity towards water splitting at neutral pH

The reaction of 2,6-diformyl-4-methylphenol, 4-methoxybenzoylhydrazine and Co(OAc)₂·4H₂O in 1 : 2 : 2 mole ratio in methanol under aerobic conditions produced in 61% yield a tetranuclear complex having the molecular formula [Co^IICo^III(μ-OAc)(μ₃-OH)(μ-L)]₂ where OAc^- and L^3- represent acetate and N',N''-(5-methyl-2-oxido-1,3-phenylene)bis(methan-1-yl-1-ylidene)bis(4-methoxybenzoylhydrazonate), respectively. The elemental analysis and the mass spectrometric data confirmed the molecular formula of the complex. It is electrically non-conducting and paramagnetic. The complex crystallized as acetonitrile solvate. The X-ray structure shows that each Co(II) centre has a distorted square-pyramidal NO₄ coordination sphere, while each Co(III) centre is in a distorted octahedral NO₅ environment. The four metal atoms and the four bridging O-atoms form an open cubane type Co₄O₄ motif. In the crystal lattice, self-assembly of the solvated complex via intermolecular O-H⋯O interaction leads to a two-dimensional network structure. The infrared and electronic spectroscopic features of the complex are consistent with its molecular structure. Cryomagnetic measurements together with theoretical calculations suggest the presence of easy-axis anisotropy for the square-pyramidal Co(II) centres. The complex is redox-active and displays metal centred oxidation and reduction responses on the anodic and cathodic sides, respectively, of the Ag/AgCl electrode. Bifunctional heterogeneous electrocatalytic activity of the complex towards O₂ and H₂ evolution reactions (OER and HER) in neutral aqueous medium has been explored in detail.

Automated search for optimal surface phases (ASOPs) in grand canonical ensemble powered by machine learning

The surface of a material often undergoes dramatic structure evolution under a chemical environment, which, in turn, helps determine the different properties of the material. Here, we develop a general-purpose method for the automated search of optimal surface phases (ASOPs) in the grand canonical ensemble, which is facilitated by the stochastic surface walking (SSW) global optimization based on global neural network (G-NN) potential. The ASOP simulation starts by enumerating a series of composition grids, then utilizes SSW-NN to explore the configuration and composition spaces of surface phases, and relies on the Monte Carlo scheme to focus on energetically favorable compositions. The method is applied to silver surface oxide formation under the catalytic ethene epoxidation conditions. The known phases of surface oxides on Ag(111) are reproduced, and new phases on Ag(100) are revealed, which exhibit novel structure features that could be critical for understanding ethene epoxidation. Our results demonstrate that the ASOP method provides an automated and efficient way for probing complex surface structures that are beneficial for designing new functional materials under working conditions.

Splicing the active phases of copper/cobalt-based catalysts achieves high-rate tandem electroreduction of nitrate to ammonia

Electrocatalytic recycling of waste nitrate (NO₃⁻) to valuable ammonia (NH₃) at ambient conditions is a green and appealing alternative to the Haber−Bosch process. However, the reaction requires multi-step electron and proton transfer, making it a grand challenge to drive high-rate NH₃ synthesis in an energy-efficient way. Herein, we present a design concept of tandem catalysts, which involves coupling intermediate phases of different transition metals, existing at low applied overpotentials, as cooperative active sites that enable cascade NO₃⁻-to-NH₃ conversion, in turn avoiding the generally encountered scaling relations. We implement the concept by electrochemical transformation of Cu−Co binary sulfides into potential-dependent core−shell Cu/CuO_x and Co/CoO phases. Electrochemical evaluation, kinetic studies, and in−situ Raman spectra reveal that the inner Cu/CuO_x phases preferentially catalyze NO₃⁻ reduction to NO₂⁻, which is rapidly reduced to NH₃ at the nearby Co/CoO shell. This unique tandem catalyst system leads to a NO₃⁻-to-NH₃ Faradaic efficiency of 93.3 ± 2.1% in a wide range of NO₃⁻ concentrations at pH 13, a high NH₃ yield rate of 1.17 mmol cm⁻² h⁻¹ in 0.1 M NO₃⁻ at −0.175 V vs. RHE, and a half-cell energy efficiency of ~36%, surpassing most previous reports.

Electrocatalytic recycling of waste nitrate to NH₃ under ambient conditions maybe an appealing alternative to the Haber−Bosch process. Here the authors report a tandem catalyst system involving cooperative adsorption of reaction intermediate on different transition metal active sites for nitrate electroreduction with high efficiency.

Increased crystallinity of RuSe2/carbon nanotubes for enhanced electrochemical hydrogen generation performance

Ru-Based catalysts are significant in the green hydrogen generation via the electrochemical water-splitting reaction. Herein, it is found that the increased crystallinity of cubic RuSe₂ nanoparticles anchored over carbon nanotubes (RuSe₂/CNTs) could largely increase the hydrogen generation performance both in acidic and alkaline electrolytes. The freshly prepared RuSe₂/CNTs with low crystallinity had a very low catalytic performance for the HER, while the catalytic ability could be largely boosted by facile thermal annealing at 650 °C in an N₂ atmosphere, resulting from the increased crystallinity and electronic effect. The crystal structure enhancement of the RuSe₂ nanoparticles was well supported by the X-ray diffraction technique and the lattice fringes in the high-resolution transmission electron microscopy images. As a result, the catalyst exhibited largely improved catalytic performance compared to the freshly prepared RuSe₂/CNTs; specifically, the overpotentials of 48 and 64 mV were required to drive 10 mA cm^-2 in alkaline and acidic media when loaded on a glassy carbon electrode, much less than those of 109 and 120 mV for the freshly prepared RuSe₂/CNTs; the catalytic performance in the alkaline electrolyte was even close to that of the commercial Pt/C catalyst. Correspondingly, the improved catalytic stability, catalytic kinetics, charge transfer ability and catalytic efficiency of the active sites were also observed. The current work shows an effective approach and important understanding for catalytic performance enhancement via increased crystallinity by facile thermal annealing.

Free-base porphyrin polymer for bifunctional electrochemical water splitting

Water splitting is considered a promising approach for renewable and sustainable energy conversion. The development of water splitting electrocatalysts that have low-cost, long-lifetime, and high-performance is an important area of research for the sustainable generation of hydrogen and oxygen gas. Here, we report a metal-free porphyrin-based two-dimensional crystalline covalent organic polymer obtained from the condensation of terephthaloyl chloride and 5,10,15,20-tetrakis(4-aminophenyl) porphyrin which is stabilized by an extensive hydrogen bonding network. This material exhibits bifunctional electrocatalytic performance towards water splitting with onset overpotentials, η, of 36 mV and 110 mV for HER (in 0.5 M H₂SO₄) and OER (in 1.0 M KOH), respectively. The as-synthesized material is also able to perform water splitting in neutral phosphate buffer saline solution, with 294 mV for HER and 520 mV for OER, respectively. Characterized by electrochemical impedance spectroscopy (EIS) and chronoamperometry, the as-synthesized material also shows enhanced conductivity and stability compared to its molecular counterpart. Inserting a non-redox active zinc metal center in the porphyrin unit leads to a decrease in electrochemical activity towards both HER and OER, suggesting the four-nitrogen porphyrin core is the active site. The high performance of this metal-free material towards water splitting provides a sustainable alternative to the use of scarce and expensive metal electrocatalysts in energy conversion for industrial applications.

Water splitting is considered a promising approach for renewable and sustainable energy conversion.

In situ integration of cobalt diselenide nanoparticles on CNTs realizing durable hydrogen evolution

Cobalt diselenide (CoSe₂) is considered to be a promising economical and efficient electrocatalyst for the hydrogen evolution reaction (HER). Here carbon nanotubes (CNTs) were employed as a conductive skeleton to optimize the electrocatalytic performance of CoSe₂ through a simple one-step hydrothermal method. Beyond the expected, the introduction of CNTs not only accelerates electron transportation and ion diffusion, but also improves the reaction kinetics for HER by forming a CoSe₂/CNT heterointerface. Consequently, the CoSe₂/CNTs composite exhibits an optimal overpotential of 153 mV with a weight ratio of 10 : 1, and sustains a long period of 48 hours with an negligible overpotential deterioration. In addition, a Faraday efficiency of 97.67% is achieved with a H₂/O₂ molar ratio of 2 : 1. Therefore, these results open up further opportunities for yielding efficient and durable hydrogen evolving electrocatalysts from low-cost transition metal compounds.

The CoSe₂/CNT composites are integrated as electrocatalysts for the hydrogen evolution reaction, providing a new way to construct durable electrocatalysts from transition metal compounds.

Complementary combinative strategy of defect engineering and graphene coupling for efficient energy-functional materials

The synergetic combination of defect engineering and graphene coupling enables to develop an effective way of exploring efficient bifunctional electrocatalyst/electrode materials. Defect-engineered amorphous MoO₂ -reduced graphene oxide (rGO) nanohybrid was synthesized by soft-chemical reduction of K₂ MoO₄ in graphene oxide colloids. Mo K-edge X-ray absorption spectroscopy clearly demonstrates the rutile-type local atomic structure of amorphous MoO₂ with significant oxygen vacancies and intimate electronic coupling with rGO. The defect-introduced MoO₂ -rGO nanohybrid shows excellent bifunctionality as electrocatalyst for hydrogen evolution reaction and electrode for sodium-ion batteries, which are superior to those of crystalline MoO₂ -rGO homologue. The beneficial effect of simultaneous defect control and rGO coupling can be ascribed to the provision of oxygen vacancies acting as active sites, the increase of electrical conductivity, and the improvement of reaction kinetics.

Graphene oxide wrapped Mix-valent cobalt phosphate hollow nanotubes as oxygen evolution catalyst with low overpotential

Development of an efficient, stable and inexpensive catalyst for oxygen evolution reaction (OER) is critical to electrochemical water splitting. In this regard, a precious-metal free electrocatalyst has been synthesized employing a hydrothermal route. The prepared graphene oxide wrapped cobalt phosphate nanotubes deposited on Ni foam electrode shows a low overpotential of 234 mV at a current density of 10 mA/cm² for OER in 1(M) KOH, lower than a benchmarking electrocatalyst IrO₂ at the same current density. The performance figures clearly defy the volcano limitations. The mixed-valency induced delocalization of charge satisfies Sabatier Principle for ideal catalysts and graphene oxide ensures improved charge transfer. Moreover, the designed electrocatalyst performs efficiently even on prolonged use under mass transfer limitation conditions.

Nanoblackberries of {W72Fe33} and {Mo72Fe30}: Electrocatalytic Water Reduction

The reversible self-assembly of a {Mo₇₂Fe₃₀} cluster into nanoblackberries in a dilute solution of the relevant crystalline compound [Mo₇₂Fe₃₀O₂₅₂(CH₃COO)₁₂{Mo₂O₇(H₂O)}₂{H₂Mo₂O₈(H₂O)}(H₂O)₉₁]·150H₂O ({Mo₇₂Fe₃₀}_cryst) was demonstrated by Liu, Müller, and their co-workers as a landmark discovery in the area of polyoxometalate chemistry. We have described, in the present work, how these ∼2.5 nm nano-objects, {M₇₂Fe₃₀} (M = W, Mo) can be self-assembled into nanoblackberries irreversibly, leading to their solid-state isolation as the nanomaterials Fe₃[W₇₂Fe₃₀O₂₅₂(CH₃COO)₂(OH)₂₅(H₂O)₁₀₃]·180H₂O ({W₇₂Fe₃₃}_NM) and Na₂[Mo₇₂Fe₃₀O₂₅₂(CH₃COO)₄(OH)₁₆(H₂O)₁₀₈]·180H₂O ({Mo₇₂Fe₃₀}_NM), respectively (NM stands for nanomaterial). The formulations of these one-pot-synthesized nanoblackberries of {W₇₂Fe₃₃}_NM and {Mo₇₂Fe₃₀}_NM have been established by spectral analysis including Raman spectroscopy, elemental analysis including ICP metal analysis, volumetric analysis (for iron), microscopy techniques, and DLS studies. The thermal stability of the tungsten nanoblackberries {W₇₂Fe₃₃}_NM is much higher than that of its molybdenum analogue {Mo₇₂Fe₃₀}_NM. This might due to the extra three ferric (Fe³⁺) ions per {W₇₂Fe₃₀} cluster in {W₇₂Fe₃₃}_NM, which are not part of the {W₇₂Fe₃₀} cluster cage but are placed between two adjacent clusters (i.e., each cluster has six surrounding 0.5Fe³⁺) to form this self-assembly. The isolated blackberries behave like an inorganic acid, a water suspension of which shows pH values of 3.9 for {W₇₂Fe₃₃}_NM and 3.7 for {Mo₇₂Fe₃₀}_NM because of the deprotonation of the hydroxyl groups in them. We have demonstrated, for the first time, a meaningful application of these inexpensive and easily synthesized nanoblackberries by showing that they can act as electrocatalysts for the hydrogen evolution reaction (HER) by reducing water. We have performed detailed kinetic studies for the electrocatalytic water reduction catalyzed by {W₇₂Fe₃₃}_NM and {Mo₇₂Fe₃₀}_NM in a comparative study. The relevant turnover frequencies (TOFs) of {W₇₂Fe₃₃}_NM and {Mo₇₂Fe₃₀}_NM (∼0.72 and ∼0.45 s^-1, respectively), the overpotential values of {W₇₂Fe₃₃}_NM and {Mo₇₂Fe₃₀}_NM (527 and 767 mV, respectively at 1 mA cm^-2), and the relative stability issues of the catalysts indicate that {W₇₂Fe₃₃}_NM is reasonably superior to {Mo₇₂Fe₃₀}_NM. We have described a rationale of why {W₇₂Fe₃₃}_NM performs better than {Mo₇₂Fe₃₀}_NM in terms of catalytic activity and stability.

Voltage cycling process for the electroconversion of biomass-derived polyols

Electrification of chemical reactions is crucial to fundamentally transform our society that is still heavily dependent on fossil resources and unsustainable practices. In addition, electrochemistry-based approaches offer a unique way of catalyzing reactions by the fast and continuous alteration of applied potentials, unlike traditional thermal processes. Here, we show how the continuous cyclic application of electrode potential allows Pt nanoparticles to electrooxidize biomass-derived polyols with turnover frequency improved by orders of magnitude compared with the usual rates at fixed potential conditions. Moreover, secondary alcohol oxidation is enhanced, with a ketoses-to-aldoses ratio increased up to sixfold. The idea has been translated into the construction of a symmetric single-compartment system in a two-electrode configuration. Its operation via voltage cycling demonstrates high-rate sorbitol electrolysis with the formation of H2 as a desired coproduct at operating voltages below 1.4 V. The devised method presents a potential approach to using renewable electricity to drive chemical processes.

Origin of enhanced water oxidation activity in an iridium single atom anchored on NiFe oxyhydroxide catalyst

The efficiency with which renewable fuels and feedstocks are synthesized from electrical sources is largely limited by the sluggish water oxidation reaction. We show that the optimal water oxidation catalyst could be achieved by systematically modulating the coordination of the Ir active sites using an in situ cryogenic–photochemical reduction synthesis method. We achieved a highly oxidized Ir single site (Ir^+5.3) in the best atom utilization by single-atom catalysts on electrochemically stable supports. The origin of water oxidation activity in an Ir single-atom catalyst is revealed experimentally and theoretically. The concept and strategy of this work are expected to pioneer novel approaches to engineer single-atom catalysts.

The efficiency of the synthesis of renewable fuels and feedstocks from electrical sources is limited, at present, by the sluggish water oxidation reaction. Single-atom catalysts (SACs) with a controllable coordination environment and exceptional atom utilization efficiency open new paradigms toward designing high-performance water oxidation catalysts. Here, using operando X-ray absorption spectroscopy measurements with calculations of spectra and electrochemical activity, we demonstrate that the origin of water oxidation activity of IrNiFe SACs is the presence of highly oxidized Ir single atom (Ir^5.3+) in the NiFe oxyhydroxide under operating conditions. We show that the optimal water oxidation catalyst could be achieved by systematically increasing the oxidation state and modulating the coordination environment of the Ir active sites anchored atop the NiFe oxyhydroxide layers. Based on the proposed mechanism, we have successfully anchored Ir single-atom sites on NiFe oxyhydroxides (Ir_0.1/Ni₉Fe SAC) via a unique in situ cryogenic–photochemical reduction method that delivers an overpotential of 183 mV at 10 mA ⋅ cm⁻² and retains its performance following 100 h of operation in 1 M KOH electrolyte, outperforming the reported catalysts and the commercial IrO₂ catalysts. These findings open the avenue toward an atomic-level understanding of the oxygen evolution of catalytic centers under in operando conditions.

Bridging Thermal Catalysis and Electrocatalysis: Catalyzing CO2 Conversion with Carbon-Based Materials

Understanding the differences between reactions driven by elevated temperature or electric potential remains challenging, largely due to materials incompatibilities between thermal catalytic and electrocatalytic environments. We show that Ni, N-doped carbon (NiPACN), an electrocatalyst for the reduction of CO₂ to CO (CO₂ R), can also selectively catalyze thermal CO₂ to CO via the reverse water gas shift (RWGS) representing a direct analogy between catalytic phenomena across the two reaction environments. Advanced characterization techniques reveal that NiPACN likely facilitates RWGS on dispersed Ni sites in agreement with CO₂ R active site studies. Finally, we construct a generalized reaction driving-force that includes temperature and potential and suggest that NiPACN could facilitate faster kinetics in CO₂ R relative to RWGS due to lower intrinsic barriers. This report motivates further studies that quantitatively link catalytic phenomena across disparate reaction environments.

2D coordination polymer-derived CoSe2-NiSe2/CN nanosheets: the dual-phase synergistic effect and ultrathin structure to enhance the hydrogen evolution reaction

The evolution of cost-effective hydrogen evolution reaction (HER) electrocatalysts is of great significance for the development of clean energy. Exploring effective synthesis strategies to optimize the performance of non-noble metal electrocatalysts has always attracted our attention. Herein, ultrathin coordination polymers were used as precursors to controllably synthesize two-dimensional (2D) ultrathin dual-phase transition metal selenide (TMSs)/carbon-nitrogen (CN) composites (CoSe2-NiSe2/CN) by a two-step method (first a low temperature hydrothermal method for selenization, and then high temperature calcination selenization). Benefiting from its large specific surface area (49 m2 g-1), abundant catalytically active sites and synergistic effects, CoSe2-NiSe2/CN can significantly enhance the HER catalytic activity and exhibits good electrocatalytic activity with an overpotential of 150 mV at -10 mA cm-2, and a small Tafel slope of 42 mV dec-1 in an acidic electrolyte for the HER. This work provides a new strategy for optimizing the HER catalytic activity of TMSs by preparing 2D ultrathin dual-phase TMS composite materials.

Unraveling the Ion Adsorption Kinetics in Microporous Carbon Electrodes: A Multiscale Quantum-Continuum Simulation and Experimental Approach

Understanding sorption in porous carbon electrodes is crucial to many environmental and energy technologies, such as capacitive deionization (CDI), supercapacitor energy storage, and activated carbon filters. In each of these examples, a practical model that can describe ion electrosorption kinetics is highly desirable for accelerating material design. Here, we proposed a multiscale model to study the ion electrosorption kinetics in porous carbon electrodes by combining quantum mechanical simulations with continuum approaches. Our model integrates the Butler-Volmer (BV) equation for sorption kinetics and a continuously stirred tank reactor (CSTR) formulation with atomistic calculations of ion hydration and ion-pore interactions based on density functional theory (DFT). We validated our model experimentally by using ion mixtures in a flow-through electrode CDI device and developed an in-line UV absorption system to provide unprecedented resolution of individual ions in the separation process. We showed that the multiscale model captures unexpected experimental phenomena that cannot be explained by the traditional ion electrosorption theory. The proposed multiscale framework provides a viable approach for modeling separation processes in systems where pore sizes and ion hydration effects strongly influence the sorption kinetics, which can be leveraged to explore possible strategies for improving carbon-based and, more broadly, pore-based technologies.

Transition Metal-Based 2D Layered Double Hydroxide Nanosheets: Design Strategies and Applications in Oxygen Evolution Reaction

Water splitting driven by renewable energy sources is considered a sustainable way of hydrogen production, an ideal fuel to overcome the energy issue and its environmental challenges. The rational design of electrocatalysts serves as a critical point to achieve efficient water splitting. Layered double hydroxides (LDHs) with two-dimensionally (2D) layered structures hold great potential in electrocatalysis owing to their ease of preparation, structural flexibility, and tenability. However, their application in catalysis is limited due to their low activity attributed to structural stacking with irrational electronic structures, and their sluggish mass transfers. To overcome this challenge, attempts have been made toward adjusting the morphological and electronic structure using appropriate design strategies. This review highlights the current progress made on design strategies of transition metal-based LDHs (TM-LDHs) and their application as novel catalysts for oxygen evolution reactions (OERs) in alkaline conditions. We describe various strategies employed to regulate the electronic structure and composition of TM-LDHs and we discuss their influence on OER performance. Finally, significant challenges and potential research directions are put forward to promote the possible future development of these novel TM-LDHs catalysts.

Unifying Concepts in Electro- and Thermocatalysis toward Hydrogen Peroxide Production

We examine relationships between H₂O₂ and H₂O formation on metal nanoparticles by the electrochemical oxygen reduction reaction (ORR) and the thermochemical direct synthesis of H₂O₂. The similar mechanisms of such reactions suggest that these catalysts should exhibit similar reaction rates and selectivities at equivalent electrochemical potentials (μ̅_i), determined by reactant activities, electrode potential, and temperature. We quantitatively compare the kinetic parameters for 12 nanoparticle catalysts obtained in a thermocatalytic fixed-bed reactor and a ring-disk electrode cell. Koutecky-Levich and Butler-Volmer analyses yield electrochemical rate constants and transfer coefficients, which informed mixed-potential models that treat each nanoparticle as a short-circuited electrochemical cell. These models require that the hydrogen oxidation reaction (HOR) and ORR occur at equal rates to conserve the charge on nanoparticles. These kinetic relationships predict that nanoparticle catalysts operate at potentials that depend on reactant activities (H₂, O₂), H₂O₂ selectivity, and rate constants for the HOR and ORR, as confirmed by measurements of the operating potential during the direct synthesis of H₂O₂. The selectivities and rates of H₂O₂ formation during thermocatalysis and electrocatalysis correlate across all catalysts when operating at equivalent μ̅_i values. This analysis provides quantitative relationships that guide the optimization of H₂O₂ formation rates and selectivities. Catalysts achieve the greatest H₂O₂ selectivities when they operate at high H atom coverages, low temperatures, and potentials that maximize electron transfer toward stable OOH* and H₂O₂* while preventing excessive occupation of O-O antibonding states that lead to H₂O formation. These findings guide the design and operation of catalysts that maximize H₂O₂ formation, and these concepts may inform other liquid-phase chemistries.

Enhanced electrocatalytic activity of PtRu/nitrogen and sulphur co-doped crumbled graphene in acid and alkaline media

The low mass activity and high price of pure platinum (Pt)-based catalysts predominantly limit their large-scale utilization in electrocatalysis. Therefore, the reduction of Pt amount while preserving the electrocatalytic efficiency represents a viable alternative. In this work, we prepared new PtRu₂ nanoparticles supported on sulphur and nitrogen co-doped crumbled graphene with trace amounts of iron (PtRu₂/PF) electrocatalysts. The PtRu₂/PF catalysts exhibited enhanced electrocatalytic performance and stability for the hydrogen evolution reaction (HER) at pH = 0. Moreover, the prepared PtRu₂/PF electrocatalyst displayed higher HER activity than commercial 20% Pt/C. The PtRu₂/PF catalyst achieved a current density of 10 mA cm^-2 at an overpotential value of only 22 mV for HER, performing better activity than many other Pt-based electrocatalysts. Besides, the PtRu₂/PF revealed a good performance for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) in alkaline media. The PtRu₂/PF catalyst recorded a current density of 10 mA cm^-2 at an overpotential of only 270 mV for OER in KOH (1.0 M) solution and an onset potential of 0.96 V vs. RHE (at 1 mA cm^-2) for ORR in KOH (0.1 M) solution.

Spin-polarized oxygen evolution reaction under magnetic field

The oxygen evolution reaction (OER) is the bottleneck that limits the energy efficiency of water-splitting. The process involves four electrons’ transfer and the generation of triplet state O₂ from singlet state species (OH^- or H₂O). Recently, explicit spin selection was described as a possible way to promote OER in alkaline conditions, but the specific spin-polarized kinetics remains unclear. Here, we report that by using ferromagnetic ordered catalysts as the spin polarizer for spin selection under a constant magnetic field, the OER can be enhanced. However, it does not applicable to non-ferromagnetic catalysts. We found that the spin polarization occurs at the first electron transfer step in OER, where coherent spin exchange happens between the ferromagnetic catalyst and the adsorbed oxygen species with fast kinetics, under the principle of spin angular momentum conservation. In the next three electron transfer steps, as the adsorbed O species adopt fixed spin direction, the OER electrons need to follow the Hund rule and Pauling exclusion principle, thus to carry out spin polarization spontaneously and finally lead to the generation of triplet state O₂. Here, we showcase spin-polarized kinetics of oxygen evolution reaction, which gives references in the understanding and design of spin-dependent catalysts.

Here, authors demonstrate the ferromagnetic catalyst to facilitate spin polarization in water oxidation reaction. They find the ferromagnetic-exchange-like behaviour between the ferromagnetic catalyst and the adsorbed oxygen species.

Graphite Conjugation of a Macrocyclic Cobalt Complex Enhances Nitrite Electroreduction to Ammonia

This work reports on the generation of a graphite-conjugated diimine macrocyclic Co catalyst (GCC-CoDIM) that is assembled at o-quinone edge defects on graphitic carbon electrodes. X-ray photoelectron spectroscopy and X-ray absorption spectroscopy confirm the existence of a new Co surface species with a coordination environment that is the same as that of the molecular analogue, [Co(DIM)Br₂]⁺. GCC-CoDIM selectively reduces nitrite to ammonium with quantitative Faradaic efficiency and at a rate that approaches enzymatic catalysis. Preliminary mechanistic investigations suggest that the increased rate is accompanied by a change in mechanism from the molecular analogue. These results provide a template for creating macrocycle-based electrocatalysts based on first-row transition metals conjugated to an extreme redox-active ligand.