Accelerated microbial reductive dechlorination of 2,4,6-trichlorophenol by weak electrical stimulation

Quorum sensing shaped microbial consortia and enhanced hydrogen recovery from waste activated sludge electro-fermentation on basis of free nitrous acid treatment

In this study, the feasibility of free nitrous acid (FNA) pretreatment coupled with quorum sensing (QS) was investigated to enhance hydrogen recovery from waste activated sludge (WAS) via electro-fermentation (EF). 3-oxo-hexanoyl-homoserine lactone (3OC6-HSL), as the signal molecule, was only added in the first three cycles of sludge inoculation at the phase of microbial electrolysis cells (MECs) startup. Results showed that QS combined FNA (AHL-FMEC) enabled highest hydrogen yield and current (4.3 mg/g VSS and 4.5 mA), while that generated from sole FNA/QS treated WAS (FMEC/AHL-RMEC) were only 3.5/3.0 mg/g VSS and 1.5/1.5 mA, respectively. Fourier transform infrared (FT-IR) spectra illustrated the effective conversion of organics in AHL-FMEC, the utilization efficiencies of proteins and carbohydrates achieved to 75.0% and 79.7%, respectively. Besides, the internal resistance decreased from 34.5 Ω (FMEC) to 22.9 Ω (AHL-RMEC), further to 18.0 Ω, indicating the promoted bioelectrochemical activity of electroactive bacteria (EAB) in AHL-FMEC. Correspondingly, both EAB (21.7%), e.g., Geobacter (9.3%) and Pseudomonas (3.2%) and anaerobic fermentation bacteria (AFB, 28.6%), e.g., Proteiniclasticum (14.2%) and Petrimonas (3.6%) enriched to peaks in AHL-FMEC. Moreover, molecular ecological network (MEN) analysis revealed the underling relationships among AFB, EAB and homo-acetogen in EF system, suggesting the possible cooperative QS has been constructed. The results obtained in this study may provide a new insight for efficient hydrogen recovery from electro-fermentation of WAS.

Challenges and opportunities for the biodegradation of chlorophenols: Aerobic, anaerobic and bioelectrochemical processes

Chlorophenols (CPs) are highly toxic and refractory contaminants which widely exist in various environments and cause serious harm to human and environment health and safety. This review provides comprehensive information on typical CPs biodegradation technologies, the most green and benign ones for CPs removal. The known aerobic and anaerobic degradative bacteria, functional enzymes, and metabolic pathways of CPs as well as several improving methods and critical parameters affecting the overall degradation efficiency are systematically summarized and clarified. The challenges for CPs mineralization are also discussed, mainly including the dechlorination of polychlorophenols (poly-CPs) under aerobic condition and the ring-cleavage of monochlorophenols (MCPs) under anaerobic condition. The coupling of functional materials and degraders as well as the operation of sequential anaerobic-aerobic bioreactors and bioelectrochemical system (BES) are promising strategies to overcome some current limitations. Future perspective and research gaps in this field are also proposed, including the further understanding of microbial information and the specific role of materials in CPs biodegradation, the potential application of innovative biotechnologies and new operating modes to optimize and maximize the function of the system, and the scale-up of bioreactors towards the efficient biodegradation of CPs.

Selective stress of antibiotics on microbial denitrification: Inhibitory effects, dynamics of microbial community structure and function

Antibiotics commonly exist in municipal, livestock and industrial wastewaters. However, the response of key microbiota performance in wastewater treatment plants to antibiotic exposure lacks systematic research. In this study, the short-term acute stress of four commonly used antibiotics (sulfamethoxazole, chlortetracycline, ciprofloxacin, and amoxicillin) on microbial denitrification performance was systematically investigated. All tested antibiotics exhibited the inhibitory effects in varying degrees by repeated addition for six cycles. The nitrate removal efficiencies (NrE) decreased to 7.98-26.80%, accompanied by the significant decrease of the expressed narG gene, by exposure to sulfamethoxazole, chlortetracycline or amoxicillin. Nitrite reduction was inhibited more severely than nitrate reduction, which was further verified by the low- or non-expressed nirS and nosZ genes. Furthermore, a higher antibiotic concentration made stronger inhibitory effect. Except for chlortetracycline, 2.09-6.80 times decrease of k value was commonly observed as concentration increased from 10 to 50 or 100 mg L^-1. Even in a short period (24 h), antibiotics largely decreased the abundance of the dominant denitrifying bacterial genera (Thauera, Comamonas, etc.), while, some unclassified populations (Labrenzia, Longilinea, etc.) were enriched. This study provides theoretical researches on the microbial denitrification behaviors influenced by exposure to different antibiotics.

Current intensities altered the performance and microbial community structure of a bio-electrochemical system

A novel integrated bio-electrochemical system with sulfur autotrophic denitrification (SAD) and electrocoagulation (BESAD-EC) system was established to remove nitrate (NO₃^--N) and phosphorus from contaminated groundwater. The impacts of a current intensity gradient on the system's performance and microbial community were investigated. The results showed that NO₃^--N and total phosphorus (TP) could be effectively removed with maximum NO₃^--N reduction and TP removal efficiencies of 94.2% and 75.8% at current intensities of 200 and 400 mA, respectively. Lower current intensities could improve the removal efficiencies of NO₃^--N (≤200 mA) and phosphorus (≤400 mA), while higher current intensity (600 mA) caused the inhibition of nutrients removal in the system. MiSeq sequencing analysis revealed that low electrical stimulation improved the diversity and richness of microbial community, while high electrical stimulation reduced their diversity and richness. The relative abundance of some genus involved in denitrification and phosphorus removal processes such as Rhizobium, Hydrogenophaga, Denitratisoma and Gemmobacter, significantly (P < 0.05) reduced under high current conditions. This could be one of the main reasons for the deterioration of denitrification and phosphorus removal performance. The results of this study could be helpful to enhance the nutrient removal performance of bio-electrochemical systems in groundwater treatment processes.

Biotechnology and nanotechnology for remediation of chlorinated volatile organic compounds: current perspectives

Chlorinated volatile organic compounds (CVOCs) are persistent organic pollutants which are harmful to public health and the environment. Many CVOCs occur in substantial quantities in groundwater and soil, even though their use has been more carefully managed and restricted in recent years. This review summarizes recent data on several innovative treatment solutions for CVOC-affected media including bioremediation, phytoremediation, nanoscale zero-valent iron (nZVI)-based reductive dehalogenation, and photooxidation. There is no optimally developed single technology; therefore, the possibility of using combined technologies for CVOC remediation, for example bioremediation integrated with reduction by nZVI, is presented. Some methods are still in the development stage. Advantages and disadvantages of each treatment strategy are provided. It is hoped that this paper can provide a basic framework for selection of successful CVOC remediation strategies.

Impact of electrical stimulation modes on the degradation of refractory phenolics and the analysis of microbial communities in an anaerobic-aerobic-coupled upflow bioelectrochemical reactor

An electrically stimulated anaerobic-aerobic coupled system was developed to improve the biodegradation of refractory phenolics. Expected 4-nitrophenol, 2, 4-dinitrophenol, and COD removals in the system with aerobic cathodic and anaerobic anodic chambers were approximately 53.7%, 45.4%, 22.3% (intermittent mode) and 37.9%, 19.8%, 17.3% (continuous mode) higher than that in the control system (26.0 ± 6.4%, 30.7 ± 7.1%, 49.8 ± 3.0%). 2, 4-dichlorophenol removal in the system with aerobic anodic and anaerobic cathodic chambers was approximately 28.5% higher than that in the control system (71.4 ± 5.7%). The contribution of the aerobic cathodic/anodic chambers to the removal of phenolic compounds was higher than that of the anaerobic cathodic/anodic chambers. The species related to phenolic biodegradation (Rhodococcus, Achromobacter, PSB-M-3, and Sphingobium) were enriched in the cathodic and anodic chambers of the system. These results showed that intermittent electrical stimulation could be a potential alternative for the efficient degradation of refractory phenolics.

Accelerated anaerobic biodecolorization of sulfonated azo dyes by magnetite nanoparticles as potential electron transfer mediators

Anaerobic decolorization of azo dyes has been evidenced to be an economical and effective pretreatment method, but its generally limited by the low decolorization efficiency, especially for biodecolorization sulfonated azo dyes. In this study, magnetite nanoparticles (MNPs) as a conductive material, was coupled into anaerobic system for enhancing decolorization of sulfonated azo dyes, i.e., methyl orange (MO), with technology feasibility and system stability emphasized. The results showed that the anaerobic decolorization capacity was significantly enhanced with addition of MNPs (at dose of 1 g/L), where the efficiencies of MO decolorization and aromatic amines formation were as high as 97.28 ± 0.78 % and 99.44 ± 0.25%, respectively. In addition, both electron transport system activity and sludge conductivity were also significantly improved, suggesting that a direct extracellular electron transfer had been successfully established via MNPs as RMs. Under continuous-flow experiments, addition of MNPs not only improved anaerobic system resistance environmental stress (e.g., high MO concentration, low hydraulic retention time and low co-substance concentration) but also accelerated sludge granulation. The relative abundance of functional species related to dissimilatory iron reduction and MO biodegradation were also enriched under MNPs stimulation. The observed long-term stable performance suggests the full-scale application potential of this coupled system for treatment of wastewater containing sulfonated azo dyes.

Bacteria-affinity aminated carbon nanotubes bridging reduced graphene oxide for highly efficient microbial electrocatalysis

Bioelectrochemical systems (BESs) exhibit great potential for simultaneous wastewater treatment and energy recovery. However, the efficiency of microbial electrocatalysis is fundamentally limited by the high resistance and poor biocompatibility of electrode materials. Herein, we construct a novel "binder-free" 3D biocompatible bioelectrode consists of 1D aminated carbon nanotubes (CNTs-NH₂) and 2D conductive reduced graphene oxide (rGO) nanosheets through one-step electrodeposition. As expected, the maximum current density reached to 3.25 ± 0.03 mA cm^-2 with the rGO@CNTs-NH₂ electrode, which is 4.33-fold higher than that of a bare rGO (0.75 ± 0.01 mA cm^-2), and is among the best performance reported for three-dimensional electrodes. The high microbial electrocatalytic activity is mainly attributed to the excellent performance of electron transfer and bacterial colonization, which originates from the 3D interconnecting scaffold, fast 1D CNTs "e-bridge" and positively charged surface.

Distribution characteristics and environmental fate of PCBs in marine sediments at different latitudinal regions: Insights from congener profiles

Sediments were sampled from Hangzhou Bay (HB), the South China Sea (SCS), and Antarctica (AZ) to better understand the distribution characteristics and environmental fate of polychlorinated biphenyls (PCBs) at different latitudes. Numerous PCB congeners (68) were detected among the sampling sites, supporting the ubiquity of PCB congeners. High and low chlorinated congeners dominated the PCB profiles of AZ and SCS, respectively, whereas the PCB homologues were evenly distributed in the HB. As a fraction of low chlorinated PCBs originates from an exogenous input, the low mean ratios of ∑Tetra-CBs to ∑PCBs and ∑Tetra-CBs to the sum of ∑Tri- and ∑Di-CBs suggest that microbial transformation of PCBs is weak in marine surface sediments, if any occurs at all. Furthermore, PCB contamination levels in marine sediments may be primarily influenced by latitude rather than pollution sources. Thus, the findings of this study suggest that Antarctica is becoming a prospective hotspot for PCBs.

Boosting photocatalytic chlorophenols remediation with addition of sulfite and mechanism investigation by in-situ DRIFTs

Sulfite is recently found to be promising in enhancing photocatalytic pollutants degradation, which is a byproduct from flue gas desulfuration process. Herein, 4-chlorophenol (4-CP) photodegradation was systematically investigated in a sulfite mediated system with g-C₃N₄ as photocatalyst. The degradation efficacy was improved by about 3 times with addition of 25 mM Na₂SO₃. The dominant responsible reactive oxygen species for chlorophenols remediation in the presence of sulfite included O₂^·-, SO₃^·-, and SO₄^·- as confirmed by radical quenching experiments and electron spin resonances technology. In-situ DRIFTs results indicated the improved cleavage of CCl and CH bonds with the simultaneous formation of CO and CC bonds when bisulfite was added. Degradation intermediates such as 4-chlorocatechol, hydroquinone, and muconic acid were detected by HPLC-MS. Furthermore, the photodegradation mechanisms of 4-CP were tentatively discussed . Other chlorophenols (phenol, 2-CP, 2,4-DCP, and their mixture) were also efficiently removed in the system, suggesting that sulfite could be universally applied in photocatalytic wastewater purification.

Bioelectrochemical degradation of monoaromatic compounds: Current advances and challenges

Monoaromatic compounds (MACs) are typical refractory organic pollutants which are existing widely in various environments. Biodegradation strategies are benign while the key issue is the sustainable supply of electron acceptors/donors. Bioelectrochemical system (BES) shows great potential in this field for providing continuous electrons for MACs degradation. Phenol and BTEX (Benzene, Toluene, Ethylbenzene and Xylenes) can utilize anode to enhance oxidative degradation, while chlorophenols, nitrobenzene and antibiotic chloramphenicol (CAP) can be efficiently reduced to less-toxic products by the cathode. However, there still have several aspects need to be improved including the scale, electricity output and MACs degradation efficiency of BES. This review provides a comprehensive summary on the BES degradation of MACs, and discusses the advantages, future challenges and perspectives for BES development. Instead of traditional expensive dual-chamber configurations for MACs degradation, new single-chamber membrane-less reactors are cost-effective and the hydrogen generated from cathodes may promote the anode degradation. Electrode materials are the key to improve BES performance, approaches to increase the biofilm enrichment and conductivity of materials have been discussed, including surface modification as well as composition of carbon and metal-based materials. Besides, the development and introduction of functional microbes and redox mediators, participation of sulfur/hydrogen cycling may further enhance the BES versatility. Some critical parameters, such as the applied voltage and conductivity, can also affect the BES performance, which shouldn't be overlooked. Moreover, sequential cathode-anode cascaded mode is a promising strategy for MACs complete mineralization.

Variation and distribution of antibiotic resistance genes and their potential hosts in microbial electrolysis cells treating sewage sludge

Microbial electrolysis cells (MECs) system is an emerging pollution control technology. However, information on the variation of antibiotic resistance genes (ARGs) in MECs treating sewage sludge is still very limited. In this study, the fate of ARGs and their correlation with microbes in MECs under different applied voltages (0-1.5 V) were studied. Most target ARGs were effectively removed, but tetB, tetM and tetQ were enriched up to 2.05 log units in suspended sludge. Most ARGs were mainly distributed on electrodes, except tetQ and tetM enriched in suspended sludge. The selective pressure of residual antibiotics in the sewage sludge was negligible. Horizontal gene transfer was validated for the spread of sul1, sul2, tetA and tetC in MECs. Network analysis revealed that the potential hosts of ARGs mainly belonged to Bacteroidetes, Firmicutes and Proteobacteria. Some genera related to electron transfer were newly found to be the potential ARGs hosts in MECs.

Bioremediation of typical chlorinated hydrocarbons by microbial reductive dechlorination and its key players: A review

Chlorinated hydrocarbon contamination in soils and groundwater has a severe negative impact on the human health. Microbial reductive dechlorination is a major degradation pathway of chlorinated hydrocarbon in anaerobic subsurface environments, has been extensively studied. Recent progress on the diversity of the reductive dechlorinators and the key enzymes of chlororespiration has been well reviewed. Here, we present a thorough overview of the studies related to bioremediation of chloroethenes and polychlorinated biphenyls based on enhanced in situ reductive dechlorination. The major part of this review is to provide an up-to-date summary of functional microorganisms which are either detected during in situ biostimulation or applied in bioaugmentation strategies. The applied biostimulants and corresponding reductive dechlorination products are also summarized and the future research needs are finally discussed.

Pesticides and herbicides

This paper highlights a review of scientific papers published in the year 2019 regarding pesticides and herbicides. The scientific review presented in this paper includes the presence and occurrence of pesticides and herbicides in the environment. The entire review divided into different sections, which are grouped into four main sections. Each of these sections provides studies conducted on toxicology, ecological risk assessment, strategies of treatment, policies, modeling, and guidelines regarding pesticides and herbicides management. PRACTITIONERS POINTS: This paper highlights the review of scientific literature published in the year 2019. The review includes the presence and occurrence of pesticides and herbicides in the environment. The review focuses on toxicology, ecological risk assessment, strategies of treatment, policies, modelling and guidelines regarding pesticides and herbicides management. The literature review covers selected papers relevant to the topic.

Adsorption of chlorophenols on polyethylene terephthalate microplastics from aqueous environments: Kinetics, mechanisms and influencing factors

Microplastics have received growing attention as carriers of organic pollutants in the water environment. To better understand the contribution of hydrophobic interaction, hydrogen-bonding interaction, π-π interaction and electrostatic interaction on the adsorption of hydrophilic compounds on microplastics and their adsorption behavior in natural waters, polyethylene terephthalate (PET, <150 μm) was used as an adsorbent and 4-chlorophenol (MCP), 2,4-dichlorophenol (DCP) and 2,4,6-trichlorophenol (TCP) were used as adsorbates. The results of batch adsorption experiments showed that chlorophenols (CPs) reached adsorption sites of PET through film diffusion and intra-particle diffusion. pH greatly affected the adsorption capacity. Hydrophobic interaction was the main adsorption mechanism of undissociated CPs on PET. Hydrogen-bonding interaction was also an adsorption mechanism between undissociated CPs and PET, and the contribution of hydrogen-bonding interaction to adsorption decreased with the increase of chlorine content. Meanwhile, the increase of chlorine content was favorable to the hydrophobic interaction between undissociated CPs and PET. However, higher chlorine content CPs with lower pK_a values tended to dissociate at neutral pH condition and resulted in stronger electrostatic repulsion with PET. The increase of solution ionic strength and fulvic acid content negatively affected the adsorption of DCP and TCP on PET, but did not show significant impacts on MCP adsorption. Similarly, the adsorption capacity obtained using Taihu lake water and Bohai seawater as matrices was much lower than that using laboratory water for both DCP and TCP, while the adsorption coefficient (K_d) of MCP remained at approximately 10.6 L/kg to 11.4 L/kg in the three different solution matrices. The K_d values exhibited using natural water matrices consistently followed the order of DCP > MCP > TCP. This study provides insights into the fate of CPs in the presence of microplastics and suggests that the potential risks posed by CPs and microplastics to aqueous ecosystems merit further investigation.

Transformation of the recalcitrant pesticide chlordecone by Desulfovibrio sp.86 with a switch from ring-opening dechlorination to reductive sulfidation activity

The insecticide chlordecone has been used in the French West Indies for decades, resulting in long term pollution, human health problems and social crisis. In addition to bacterial consortia and Citrobacter sp.86 previously described to transform chlordecone into three families of transformation products (A: hydrochlordecones, B: polychloroindenes and C: polychloroindenecarboxylic acids), another bacterium Desulfovibrio sp.86, showing the same abilities has been isolated and its genome was sequenced. Ring-opening dechlorination, leading to A, B and C families, was observed as previously described. Changing operating conditions in the presence of chlordecone gave rise to the formation of an unknown sulfur-containing transformation product instead of the aforementioned ones. Its structural elucidation enabled to conclude to a thiol derivative, which corresponds to an undocumented bacterial reductive sulfidation. Microbial experiments pointed out that the chlordecone thiol derivative was observed in anaerobiosis, and required the presence of an electron acceptor containing sulfur or hydrogen sulfide, in a confined atmosphere. It seems that this new reaction is also active on hydrochlordecones, as the 10-monohydrochlordecone A1 was transformed the same way. Moreover, the chlordecone thiol derivative called F1 was detected in several chlordecone contaminated mangrove bed sediments from Martinique Island, highlighting the environmental relevance of these results.

Extracellular polymeric substance decomposition linked to hydrogen recovery from waste activated sludge: Role of peracetic acid and free nitrous acid co-pretreatment in a prefermentation-bioelectrolysis cascading system

Free nitrous acid (FNA) has been recently reported to be an effective and eco-friendly inactivator for waste activated sludge (WAS), while the limited decomposition of the extracellular polymeric substance (EPS) matrix hampers resource recovery from WAS. This work employed peracetic acid (PAA) to assist FNA and explored the contribution of co-pretreatment to hydrogen recovery in a prefermentation-bioelectrolysis cascading system. The results showed that co-pretreatment led to approximately 8.8% and 20.4% increases in the exfoliation of particulate proteins and carbohydrates, respectively, from tightly bound EPS (TB-EPS) over that of sole FNA pretreatment. Electron paramagnetic resonance analysis verified that the synergistic effect of FNA, PAA and various generated free radicals was the essential process. This effect further promoted the accumulation of volatile fatty acids (VFAs) after 96 h of prefermentation, and the peak concentration in co-pretreated WAS (AD-FPWAS) was approximately 2.5-fold that in sole FNA-pretreated WAS (AD-FWAS). Subsequently, the cascading utilization of organics in the bioelectrolysis step contributed to efficient hydrogen generation. A total of 10.8 ± 0.3 mg H₂/g VSS was harvested in microbial electrolysis cells (MECs) fed with AD-FPWAS, while 6.2 ± 0.1 mg H₂/g VSS was obtained from AD-FWAS. X-ray photoelectron spectroscopy (XPS) revealed the effective decomposition of the phospholipid bilayer in the cytomembrane and the transformation of macromolecular organics into VFAs and hydrogen in the cascading system. Further microbial community analysis demonstrated that co-pretreatment enhanced the accumulation of functional consortia, including anaerobic fermentative bacteria (AFB, 28.1%), e.g., Macellibacteroides (6.3%) and Sedimentibacter (6.9%), and electrochemically active bacteria (EAB, 57.0%), e.g., Geobacter (39.0%) and Pseudomonas (13.6%), in the prefermentation and MEC steps, respectively. The possible synergetic and competitive relationships among AFB, EAB, homo-acetogens, nitrate-reducing bacteria and methanogens were explored by molecular ecological network analysis. From an environmental and economic perspective, this promising FNA and PAA co-pretreatment approach provides new insight for energy recovery from WAS biorefineries.

Efficient treatment of alizarin yellow R contained wastewater in an electrostimulated anaerobic-oxic integrated system

An electrostimulated anaerobic-oxic integrated system was constructed for treating alizarin yellow R (AYR) containing wastewater. In electro-stimulated anaerobic unit, AYR decolorization efficiency improved from 51.2% to 96.6%. Two amination metabolites, p-phenylenediamine and 5-aminosalicylic acid, went through oxidation, ammonification and mineralization in oxic unit. Electro-stimulation promoted denitrification and COD removal efficiencies by 15.5% and 8.6%, respectively. A 20% improved nitrification efficiency was observed in oxic unit, due to elimination of AYR toxicity inhibition. No corrosion of heat-treated stainless steel occurred during the 60 days of continuous operation. Electrons sunk in denitrification and decolorization accounted for 34.4-36.8% of those released from COD removal, and 7.3% increase of removed nitrogen in nitrogenous compounds (AYR, nitrate and ammonia) was found. Electro-stimulated anaerobic unit predominated with fermentation and denitrification genera (Propionispira, Rhodocyclus, etc.) and aboundance of electro-active decolorization genus (Desulfovibrio, etc.) increased. Ammonia-oxidizing genus, Comamonas, was the most abundant in aerobic unit. Compared to the suspension, the electrostimulation could increased the abundance of electro-active genera in cathodic biofilm. This study revealed the feasibility of applying electro-stimulation and the conversion laws of nitrogenous organics in secondary bio-treatment system for treating toxic nitrogenous organics-contained wastewater.

Enhanced 2,4,6-trichlorophenol degradation and biogas production with a coupled microbial electrolysis cell and anaerobic granular sludge system

A coupled microbial electrolysis cell - anaerobic granular sludge system (MEC-AGS) was established to explore the degradation efficiency of 2,4,6-trichlorophenol (TCP) with synchronous biogas production. Results showed that MEC-AGS yielded a higher proportion of CH₄ than MEC (83.8 ± 0.4% vs 82.0 ± 1.0%, P < 0.05) with sodium acetate (NaAc) as the only carbon source. Moreover, MEC-AGS had higher tolerance to the addition of TCP, with the highest TCP degradation efficiency of 45.5 ± 0.5% under 5 mg L^-1 of TCP addition in 24 h. Furthermore, microbial community structures were significantly changed based on community composition, hierarchical cluster and PCoA analysis, which proved that MEC-AGS favored the enrichment of dechlorination-related microbes such as Pseudomonas, Desulfovibrio and Longilinea, as well as their syntrophic bacteria of Anaerolineacea, Syntrophobacter, Arcobacter, etc. The coupled system provides a promising strategy for biogas production from wastewater with recalcitrant organics.

A respiration substrate-less isolation method for acute toxicity assessment

Respiration substrate (RS)-less isolation method was developed for enhancing the sensitivity of acute toxicity assessment of heavy metal ions. RS was removed from the first step of previous isolation method, which was an effective strategy for improving acute toxicity assessment. 50% inhibiting concentration (IC₅₀) values of Cu²⁺, Cd²⁺, Zn²⁺, Hg²⁺ and Ni²⁺ were 0.39 mg L^-1, 5.99 mg L^-1, 3.99 mg L^-1, 0.23 mg L^-1 and 5.74 mg L^-1, respectively. Beyond that, the complicacy of organic toxicants assessments was investigated by choosing 3,5-dichlorophenol (DCP) as model toxicant. Biofilm sensor, morphology method and suspended microbes-based methods including one-pot method, RS-isolation method, RS-less isolation method, RS-less isolation method with added potassium ferricyanide (+F), were compared. The sensitivity to DCP can be ranked as morphology method > suspended microbes-based methods > biofilm method. The difference of the present results implicated that the methodological interference, leading in different detection mechanisms of these methods. The relative investigations can provide theoretical guidance for developing comprehensive detection methods of pollutants.

Enhanced methane production by alleviating sulfide inhibition with a microbial electrolysis coupled anaerobic digestion reactor

Anaerobic digestion (AD) of organics is a challenging task under high-strength sulfate (SO₄^2-) conditions. The generation of toxic sulfides by SO₄^2--reducing bacteria (SRB) causes low methane (CH₄) production. This study investigated the feasibility of alleviating sulfide inhibition and enhancing CH₄ production by using an anaerobic reactor with built-in microbial electrolysis cell (MEC), namely ME-AD reactor. Compared to AD reactor, unionized H₂S in the ME-AD reactor was sufficiently converted into ionized HS^- due to the weak alkaline condition created via cathodic H₂ production, which relieved the toxicity of unionized H₂S to methanogenesis. Correspondingly, the CH₄ production in the ME-AD system was 1.56 times higher than that in the AD reactor with alkaline-pH control and 3.03 times higher than that in the AD reactors (no external voltage and no electrodes) without alkaline-pH control. MEC increased the amount of substrates available for CH₄-producing bacteria (MPB) to generate more CH₄. Microbial community analysis indicated that hydrogentrophic MPB (e.g. Methanosphaera) and acetotrophic MPB (e.g. Methanosaeta) participated in the two major pathways of CH₄ formation were successfully enriched in the cathode biofilm and suspended sludge of the ME-AD system. Economic revenue from increased CH₄ production totally covered the cost of input electricity. Integration of MEC with AD could be an attractive technology to alleviate sulfide inhibition and enhance CH₄ production from AD of organics under SO₄^2--rich condition.

Improving the Fenton catalytic performance of FeOCl using an electron mediator

FeOCl Fenton-like catalyst has drawn much attention due to its high catalytic activity. Nevertheless, the potential application of FeOCl is significantly hindered by the sluggish reduction kinetics of Fe³⁺ to active Fe²⁺. Here, we report that the incorporation of Fe - O-Mo electron mediator into FeOCl via forming a FeOCl/MoS₂ composite can facilitate the Fe²⁺ regeneration through the oxidation of Mo⁴⁺ to Mo⁶⁺, which boosts the hydroxyl radicals yields, thus leading to a significantly improved catalytic performance. The removal efficiency of methylene blue (MB, 50 mg L^-1) achieves ∼100% within 2 min. with low dosage of FeOCl/MoS₂ (0.2 g L^-1) and H₂O₂ (0.6 mM). FeOCl/MoS₂ not only has broad working pH range (∼3 - 9) and high salinity tolerance (100 mM), but also capable to degrade various organic pollutants. For practical application, the fabricated FeOCl/MoS₂ membrane effectively degrades continuous MB flow. This study demonstrates that incorporating an electron mediator is an effective way to improve the catalytic performance of heterogeneous Fenton-like catalysts.

Palladium/iron nanoparticles stimulate tetrabromobisphenol a microbial reductive debromination and further mineralization in sediment

Tetrabromobisphenol A (TBBPA) has aroused serious pollution in surface sediment. To date, whether and how iron-based nanoparticles could stimulate TBBPA in situ anaerobic biodegradation in sediment remains poorly understood. In this study, the distinctly enhanced TBBPA degradation activity with the rate constant k improved 4.7 times by fed with Pd/Fe nanoparticles (0.412 g L^-1 dosage, 0.5 wt% Pd loading) was observed. TBBPA degradation first went through reductive dehalogenation with bisphenol A (BPA) as the metabolites, and after the addition of Pd/Fe nanoparticles, BPA was further degraded to 4-(allene)phenol and 2,2-bis(4-hydroxyphenyl) propanoic acid via UPLC-QTOF-MS analysis, suggesting the complete detoxification potential. By the addition of Pd/Fe nanoparticles, the large amount of H₂ production (560 times higher) and the significant inhibition of methane generation facilitated the metabolism of potential reductive dehalogenators (Desulfovibrio, Clostridium, etc.), demonstrated by their increased ecological abundance and the tighter cooperative interrelations between each other. Meanwhile, the addition of Pd/Fe nanoparticles largely promoted the ecological abundance of Fe(III) reducing and aromatics degrading bacteria (Bacillus, Cryptanaerobacter, etc.), resulting in BPA further degradation. The bacterial ecological network further revealed that the potential BPA degrading bacteria shared the more positive interactions with the potential dehalogenators in the presence of Pd/Fe nanoparticles. The study firstly revealed the addition of Pd/Fe nanoparticles obviously enhanced the respiratory metabolic activities and cooperative interrelations of reductive dehalogenators and BPA degraders, which gives suggestions for in situ remediation and detoxification of BFRs in contaminated sediment.

Recirculation ratio regulates denitrifying sulfide removal and elemental sulfur recovery by altering sludge characteristics and microbial community composition in an EGSB reactor

Expanded granular sludge blanket (EGSB) is regarded as a promising reactor to carry out denitrifying sulfide removal (DSR) and elemental sulfur (S⁰) recovery. Although the recirculation ratio is an essential parameter for EGSB reactors, how it impacts the DSR process remains poorly understood. Here, three lab-scale DSR-EGSB reactors were established with the different recirculation ratios (3:1, 6:1 and 9:1) to evaluate the corresponding variations in pollutant removal, S⁰ recovery, anaerobic granular sludge (AGS) characteristics and microbial community composition. It was found that an intermediate recirculation ratio (6:1) could facilitate long-term reactor stability. Adequate recirculation ratio could enhance S⁰ recovery, but an excessive recirculation ratio (9:1) was likely to cause AGS fragmentation and biomass loss. The S⁰ desorbed more from sludge at higher recirculation ratios, probably due to the enhanced hydraulic disturbance caused by the increased recirculation ratios. At the low recirculation ratio (3:1), S⁰ accumulation as inorganic suspended solids in AGS led to a decrease in VSS/TSS ratio and mass transfer efficiency. Although typical denitrifying and sulfide-oxidizing bacteria (e.g., Azoarcus, Thauera and Arcobacter) were predominant in all conditions, facultative and heterotrophic functional bacteria (e.g., Azoarcus and Thauera) were more adaptable to higher recirculation ratios than autotrophs (e.g., Arcobacter, Thiobacillus and Vulcanibacillus), which was conducive to the formation of bacterial aggregates to response to the increased recirculation ratio. The study revealed recirculation ratio regulation significantly impacted the DSR-EGSB reactor performance by altering AGS characteristics and microbial community composition, which provides a novel strategy to improve DSR performance and S⁰ recovery.

Mixed dye wastewater treatment in a bioelectrochemical system-centered process

The feasibility of mixed dye wastewater treatment was evaluated with a novel integrated bioprocess that consisted of a hybrid anaerobic reactor (HAR) with a built-in bioelectrochemical system, an aerobic biofilm reactor (ABFR) and a denitrification reactor (DR). The position of the DR significantly affected chemical oxygen demand (COD) and colority in effluent, and placing the DR after the ABFR improved effluent quality probably due to minimization of the undesired autoxidation of aromatic amine in dye wastewater. The optimal integrated process of HAR + ABFR + DR efficiently treated mixed dye wastewater, and concentrations of COD and TN were decreased down to 75 ± 18 mg/L and 12.91 ± 0.31 mg/L, respectively, along with colority 48 ± 4 times. Total phosphorus reduced to below 0.5 mg/L with coagulation using poly aluminum chloride, and the effluent quality fully met the discharge standard. This comprehensive study suggests the feasibility of the BES based process for practical application to mixed dye wastewater treatment.

Mutual effect between electrochemically active bacteria (EAB) and azo dye in bio-electrochemical system (BES)

Herein, the mutual effect between azo dye and the performance of electrochemically active bacteria (EAB) is investigated in detail, which is crucial to understand and control the bio-electrochemical systems (BESs) operation for azo dye containing wastewater treatment. EAB is enriched at controlled potential of -0.2 V vs Ag/AgCl in single-chamber BESs. Over 95% azo dye (alizarin yellow R (AYR)) was decolorized regardless of the initial AYR concentration ranging from 30 to 120 mg/L within 24 h. The fastest decolorization rate was obtained at AYR initial concentration of 70 mg/L, which was 4.25 times greater in the closed circuit BESs than that in the open circuit one. 16S rRNA gene based microbial community analysis showed that Geobacter was dominant in EAB with relative abundance increased from 77.98% (0 mg/L AYR) to 92.22% (70 mg/L AYR), indicating that azo dye selectively boosts the growth of exoelectrogens in electrode biofilm communities. Under electricity stimulation, extracellular process can be mutually conducted by azo dye compounds, which is favorable for accelerating reaction rate and avoiding of significant toxic effect on EAB.

Microbial electrochemistry for bioremediation

Lack of suitable electron donors or acceptors is in many cases the key reason for pollutants to persist in the environment. Externally supplementation of electron donors or acceptors is often difficult to control and/or involves chemical additions with limited lifespan, residue formation or other adverse side effects. Microbial electrochemistry has evolved very fast in the past years - this field relates to the study of electrochemical interactions between microorganisms and solid-state electron donors or acceptors. Current can be supplied in such so-called bioelectrochemical systems (BESs) at low voltage to provide or extract electrons in a very precise manner. A plethora of metabolisms can be linked to electrical current now, from metals reductions to denitrification and dechlorination. In this perspective, we provide an overview of the emerging applications of BES and derived technologies towards the bioremediation field and outline how this approach can be game changing.

Performance improvement and model of a bio-electrochemical system built-in up-flow anaerobic sludge blanket for treating β-lactams pharmaceutical wastewater under different hydraulic retention time

This paper focused on the performance of an up-flow bio-electrochemical system (UBES) for treating the β-lactams pharmaceutical wastewater under different hydraulic retention time (HRT). UBES is added a bio-electrochemical system below the three-phase separator based on up-flow anaerobic sludge blanket (UASB). Comparisons of chemical oxygen demand (COD) removal, accumulation of volatile fatty acid (VFA) and biogas production were investigated during the 316-day operation time, which was divided into five parts with HRT of 96 h, 72 h, 48 h, 36 h and 20 h, respectively. The average COD removal efficiency of UBES could reach 45.3 ± 7.5%, 72.2 ± 3.5%, 86.2 ± 1.4%, 75.9 ± 1.8% and 64.9 ± 2.0%, which were 2.4%, 6.1%, 6.4%, 10.2%, 8.7% more than those of UASB under different HRTs, respectively. Biogas production as well as methane production of UBES were significantly higher than UASB during the whole changing HRT process, the maximum methane yield of UBES was 0.31 ± 0.07 L/gCOD_removed. Accumulation of VFA in UBES was discovered to be lighter than UASB, the minimum average VFA in UBES was 131.9 ± 18.5 mg/L, which was obtained at HRT of 48 h. These results proved that UBES can slow down the inhibition of VFA on methanogens to make sure a good performance on COD removal and biogas production than UASB. Moreover, the relationships between methane production and VFA, biogas production and COD consumption were analyzed. A cost and benefit were analyzed for evaluating the potential of UBES in practical applications compared with UASB. Finally, radial basis function neural network (RBFNN) model was developed and fitted well with the experimental data, which can be employed to predict the effluent quality of the UBES and UASB.