Applied and theoretical aspects of virus adsorption to surfaces

Removal of human pathogenic viruses in a down-flow hanging sponge (DHS) reactor treating municipal wastewater and health risks associated with utilization of the effluent for agricultural irrigation

A down-flow hanging sponge (DHS) reactor has been developed as a cost-effective wastewater treatment system that is adaptable to local conditions in low-income countries. A pilot-scale DHS reactor previously demonstrated stable reduction efficiencies for chemical oxygen demand (COD) and ammonium nitrogen over a year at ambient temperature, but the pathogen reduction efficiency of the DHS reactor has yet to be investigated. In the present study, the reduction efficiency of a pilot-scale DHS reactor fed with municipal wastewater was investigated for 10 types of human pathogenic viruses (norovirus GI, GII and GIV, aichivirus, astrovirus, enterovirus, hepatitis A and E viruses, rotavirus, and sapovirus). DHS influent and effluent were collected weekly or biweekly for 337 days, and concentrations of viral genomes were determined by microfluidic quantitative PCR. Aichivirus, norovirus GI and GII, enterovirus, and sapovirus were frequently detected in DHS influent, and the log₁₀ reduction (LR) of these viruses ranged from 1.5 to 3.7. The LR values for aichivirus and norovirus GII were also calculated using a Bayesian estimation model, and the average LR (±standard deviation) values for aichivirus and norovirus GII were estimated to be 1.4 (±1.5) and 1.8 (±2.5), respectively. Quantitative microbial risk assessment was conducted to calculate a threshold reduction level for norovirus GII that would be required for the use of DHS effluent for agricultural irrigation, and it was found that LRs of 2.6 and 3.7 for norovirus GII in the DHS effluent were required in order to not exceed the tolerable burden of disease at 10^-4 and 10^-6 disability-adjusted life years loss per person per year, respectively, for 95% of the exposed population during wastewater reuse for irrigation.

Potential Reservoirs and Risk Factors for VHSV IVb in an Enzootic System: Budd Lake, Michigan

Viral hemorrhagic septicemia virus genotype IVb (VHSV IVb) has caused major, sporadic fish die-offs in the Laurentian Great Lakes region of North America since 2005. Presently, factors affecting VHSV IVb persistence in enzootic systems are not well understood. Even with annual surveillance, the virus can go undetected for several years after an outbreak before again re-emerging, which suggests that the virus is maintained in the system either below detectable levels or in untested reservoirs. The aim of this study was to identify potential reservoirs of VHSV IVb in Budd Lake, Michigan; VHSV IVb was first detected in Budd Lake in 2007 but remained undetected until 2011. Additionally, we explored the susceptibility of naive fish introduced into a water body enzootic for VHSV IVb by stocking age-0 Largemouth Bass Micropterus salmoides at varying densities into enclosures in the lake. The virus was not detected among samples of the fishes Notropis spp. and Lepomis spp., cylindrical papershell mussels Anodontoides ferussacianus, leeches (subclass Hirudinea), sediment, or water. However, the virus was successfully isolated from amphipods (family Hyalellidae) and Largemouth Bass held in the enclosures. Our finding of VHSV IVb in Hyalellidae amphipods in combination with other research that has detected the virus in Diporeia spp., a large benthic amphipod important as a food resource to Great Lake fishes, suggests that benthic macroinvertebrates are a reservoir for VHSV IVb in infected systems. If there are environmental reservoirs for VHSV IVb in infected systems, they are likely unevenly distributed. Findings of this study add to our understanding of the seemingly complex ecology of this deadly and economically detrimental virus. Received February 22, 2016; accepted October 16, 2016.

Different Behavior of Enteric Bacteria and Viruses in Clay and Sandy Soils after Biofertilization with Swine Digestate

Enteric pathogens from biofertilizer can accumulate in the soil, subsequently contaminating water and crops. We evaluated the survival, percolation and leaching of model enteric pathogens in clay and sandy soils after biofertilization with swine digestate: PhiX-174, mengovirus (vMC0), Salmonella enterica Typhimurium and Escherichia coli O157:H7 were used as biomarkers. The survival of vMC0 and PhiX-174 in clay soil was significantly lower than in sandy soil (iT90 values of 10.520 ± 0.600 vs. 21.270 ± 1.100 and 12.040 ± 0.010 vs. 43.470 ± 1.300, respectively) and PhiX-174 showed faster percolation and leaching in sandy soil than clay soil (iT90 values of 0.46 and 2.43, respectively). S. enterica Typhimurium was percolated and inactivated more slowly than E. coli O157:H7 (iT90 values of 9.340 ± 0.200 vs. 6.620 ± 0.500 and 11.900 ± 0.900 vs. 10.750 ± 0.900 in clay and sandy soils, respectively), such that E. coli O157:H7 was transferred more quickly to the deeper layers of both soils evaluated (percolation). Our findings suggest that E. coli O157:H7 may serve as a useful microbial biomarker of depth contamination and leaching in clay and sandy soil and that bacteriophage could be used as an indicator of enteric pathogen persistence. Our study contributes to development of predictive models for enteric pathogen behavior in soils, and for potential water and food contamination associated with biofertilization, useful for risk management and mitigation in swine digestate recycling.

The survival and inactivation of enteric viruses on soft surfaces: A systematic review of the literature

BACKGROUND

Worldwide, enteric viruses are the main cause of acute gastroenteritis. In humans, these viruses spread via person-to-person contact, food, water, and/or the environment. Their survival and inactivation on hard surfaces have been extensively studied; however, nonlaunderable soft surfaces, such as upholstery and carpet, have received little attention. The aim of this systematic review was to determine factors that influence the survival and inactivation of enteric viruses on nonlaunderable soft surfaces.

METHODS

EBSCO and Web of Science were searched for experimental studies published between 1965 and 2015 using Preferred Reporting Items for Systematic Reviews and Meta-Analyses methods. Titles and abstracts were screened using 3 eligibility criteria. The quality of all study methods was also assessed.

RESULTS

Our search yielded 12 articles. Viruses survived between 0 hours and 140 days depending on surface and environment conditions. Virus survival was influenced by temperature, relative humidity, organic content, and deposition method. A variety of chemistries were tested across studies and were shown to have a varied effect on enteric viruses. Chlorine, glutaraldehyde, vaporous ozone, and hydrogen peroxide were the most efficacious against enteric viruses (> 3-log reduction).

CONCLUSIONS

Environmental factors, such as temperature and relative humidity, can influence survival of enteric viruses on nonlaunderable soft surfaces. The efficacy of liquid and vaporous chemistries are associated with surface and virus type.

Field-based evaluation of a male-specific (F+) RNA coliphage concentration method

Fecal contamination of water poses a significant risk to public health due to the potential presence of pathogens, including enteric viruses. Therefore, sensitive, reliable and easy to use methods for the concentration, detection and quantification of microorganisms associated with the safety and quality of water are needed. In this study, we performed a field evaluation of an anion exchange resin-based method to concentrate male-specific (F+) RNA coliphages (FRNA), fecal indicator organisms, from diverse environmental waters that were suspected to be contaminated with feces. In this system, FRNA coliphages are adsorbed to anion exchange resin and direct nucleic acid isolation is performed, yielding a sample amenable to real-time reverse transcriptase (RT)-PCR detection. Matrix-dependent inhibition of this method was evaluated using known quantities of spiked FRNA coliphages belonging to four genogroups (GI, GII, GII and GIV). RT-PCR-based detection was successful in 97%, 72%, 85% and 98% of the samples spiked (10⁶ pfu/l) with GI, GII, GIII and GIV, respectively. Differential FRNA coliphage genogroup detection was linked to inhibitors that altered RT-PCR assay efficiency. No association between inhibition and the physicochemical properties of the water samples was apparent. Additionally, the anion exchange resin method facilitated detection of naturally present FRNA coliphages in 40 of 65 environmental water samples (61.5%), demonstrating the viability of this system to concentrate FRNA coliphages from water.

Long-term inactivation of bacteriophage PRD1 as a function of temperature, pH, sodium and calcium concentration

The two most significant processes controlling virus mobility in the subsurface environment are virus attachment and inactivation. In particular, models that predict subsurface virus transport are highly sensitive to inactivation. Virus inactivation is known to depend on temperature as well as hydrochemical conditions. The aim of the current work was to study the effects of temperature and hydrochemical conditions on the inactivation of bacteriophage PRD1 as a model virus, and to develop a quantitative relation for these effects. Series of batch experiments under controlled temperature were conducted, for a range of conditions: 9.5 °C and 12 °C, pH4 - pH8, sodium concentrations of 1, 10 and 20 mM, and calcium concentrations of 0.5, 1.5, and 3 mM. By multivariate regression analysis, a joint log-square model was developed that describes the inactivation rate of PRD1 as a function of these hydrochemical conditions. This model approximates two rate and Weibull models and accounts for the observed non-linear inactivation at increased pH and salt concentrations. Model predictions are within ±0.4 log10 (0.4-2.5 times) virus concentration reduction. The nature of the log-square model does not allow extrapolation of virus inactivation beyond the experimental conditions. Inactivation rate of PRD1 was found to increase with increasing temperature and increasing sodium and calcium concentrations, and to be lowest between pH 6.5 and pH 7.5. Within the studied conditions, the developed log-square model may be applied at field scale for predicting inactivation during subsurface transport of viruses.

Influence of Environmental Factors on Phage-Bacteria Interaction and on the Efficacy and Infectivity of Phage P100

When using bacteriophages to control food-borne bacteria in food production plants and processed food, it is crucial to consider that environmental conditions influence their stability. These conditions can also affect the physiological state of bacteria and consequently host–virus interaction and the effectiveness of the phage ability to reduce bacteria numbers. In this study we investigated the stability, binding, and replication capability of phage P100 and its efficacy to control Listeria monocytogenes under conditions typically encountered in dairy plants. The influences of SDS, Lutensol AO 7, salt, smear water, and different temperatures were investigated. Results indicate that phage P100 is stable and able to bind to the host under most conditions tested. Replication was dependent upon the growth of L. monocytogenes and efficacy was higher when bacterial growth was reduced by certain environmental conditions. In long-term experiments at different temperatures phages were initially able to reduce bacteria up to seven log₁₀ units after 2 weeks at 4°C. However, thereafter, re-growth and development of phage-resistant L. monocytogenes isolates were encountered.

Strain-Specific Virolysis Patterns of Human Noroviruses in Response to Alcohols

Alcohol-based hand sanitizers are widely used to disinfect hands to prevent the spread of pathogens including noroviruses. Alcohols inactivate norovirus by destruction of the viral capsid, resulting in the leakage of viral RNA (virolysis). Since conflicting results have been reported on the susceptibility of human noroviruses against alcohols, we exposed a panel of 30 human norovirus strains (14 GI and 16 GII strains) to different concentrations (50%, 70%, 90%) of ethanol and isopropanol and tested the viral RNA titer by RT-qPCR. Viral RNA titers of 10 (71.4%), 14 (100%), 3 (21.4%) and 7 (50%) of the 14 GI strains were reduced by > 1 log10 RNA copies/ml after exposure to 70% and 90% ethanol, and 70% and 90% isopropanol, respectively. RNA titers of 6 of the 7 non-GII 4 strains remained unaffected after alcohol exposure. Compared to GII strains, GI strains were more susceptible to ethanol than to isopropanol. At 90%, both alcohols reduced RNA titers of 8 of the 9 GII.4 strains by ≥ 1 log10 RNA copies/ml. After exposure to 70% ethanol, RNA titers of GII.4 Den Haag and Sydney strains decreased by ≥ 1.9 log10, whereas RNA reductions for GII.4 New Orleans strains were < 0.5 log10. To explain these differences, we sequenced the complete capsid gene of the 9 GII.4 strains and identified 17 amino acid substitutions in the P2 region among the 3 GII.4 variant viruses. When comparing with an additional set of 200 GII.4 VP1 sequences, only S310 and P396 were present in all GII.4 New Orleans viruses but not in the ethanol-sensitive GII.4 Sydney and GII.4 Den Haag viruses Our data demonstrate that alcohol susceptibility patterns between different norovirus genotypes vary widely and that virolysis data for a single strain or genotype are not representative for all noroviruses.

Functionalized Surfaces with Tailored Wettability Determine Influenza A Infectivity

Surfaces contaminated with pathogenic microorganisms contribute to their transmission and spreading. The development of "active surfaces" that can reduce or eliminate this contamination necessitates a detailed understanding of the molecular mechanisms of interactions between the surfaces and the microorganisms. Few studies have shown that, among the different surface characteristics, the wetting properties play an important role in reducing virus infectivity. Here, we systematically tailored the wetting characteristics of flat and nanostructured glass surfaces by functionalizing them with alkyl- and fluoro-silanes. We studied the effects of these functionalized surfaces on the infectivity of Influenza A viruses using a number of experimental and computational methods including real-time fluorescence microscopy and molecular dynamics simulations. Overall, we show that surfaces that are simultaneously hydrophobic and oleophilic are more efficient in deactivating enveloped viruses. Our results suggest that the deactivation mechanism likely involves disruption of the viral membrane upon its contact with the alkyl chains. Moreover, enhancing these specific wetting characteristics by surface nanostructuring led to an increased deactivation of viruses. These combined features make these substrates highly promising for applications in hospitals and similar infrastructures where antiviral surfaces can be crucial.

Technical aspects of using human adenovirus as a viral water quality indicator

Despite dramatic improvements in water treatment technologies in developed countries, waterborne viruses are still associated with many of cases of illness each year. These illnesses include gastroenteritis, meningitis, encephalitis, and respiratory infections. Importantly, outbreaks of viral disease from waters deemed compliant from bacterial indicator testing still occur, which highlights the need to monitor the virological quality of water. Human adenoviruses are often used as a viral indicator of water quality (faecal contamination), as this pathogen has high UV-resistance and is prevalent in untreated domestic wastewater all year round, unlike enteroviruses and noroviruses that are often only detected in certain seasons. Standard methods for recovering and measuring adenovirus numbers in water are lacking, and there are many variations in published methods. Since viral numbers are likely under-estimated when optimal methods are not used, a comprehensive review of these methods is both timely and important. This review critically evaluates how estimates of adenovirus numbers in water are impacted by technical manipulations, such as during adenovirus concentration and detection (including culturing and polymerase-chain reaction). An understanding of the implications of these issues is fundamental to obtaining reliable estimation of adenovirus numbers in water. Reliable estimation of HAdV numbers is critical to enable improved monitoring of the efficacy of water treatment processes, accurate quantitative microbial risk assessment, and to ensure microbiological safety of water.

Concentration and detection of hepatitis A virus and its indicator from artificial seawater using zeolite

Hepatitis A virus (HAV) infection is the leading worldwide cause of acute viral hepatitis, and outbreaks caused by this virus often occur in fecal polluted waters. Rapid concentration and detection of viral contamination in water environments can prevent economic loss and can identify the source of contamination within a short time. However, conventional methods for virus concentration are often laborious, time consuming, and subject to clogging. Furthermore, most methods require a secondary concentration step to reduce the final volume of samples. We developed a method to concentrate HAV from seawater using zeolite in aid of rapid detection. In this method,artificial seawater was inoculated with HAV (7-8 log TCID50) and filtered with zeolite. The viruses were then eluted from zeolite with sodium dodecyl sulfate and detected via real-time PCR (qPCR). Zeolite was able to concentrate HAV from artificial seawater with ∼99% efficiency in less than 5min and was more efficient in seawater than in fresh water. The entire concentration and detection can be done in approximately 2h. Compared to existing methods, this method eliminated the need for a secondary concentration step as well as the necessity to modify the pH or salinity of the seawater during concentration, and was simple and inexpensive.

Low viral predation pressure in cold hypersaline Arctic sediments and limits on lytic replication

Viruses are ubiquitous drivers of microbial ecology and evolution and contribute to biogeochemical cycling. Attention to these attributes has been more substantial for marine viruses than viruses of other environments. Microscopy-based investigation of the viral communities from two cold, hypersaline Arctic springs was undertaken to explore the effects of these conditions on microbe-viral ecology. Sediments and water samples were collected along transects from each spring, from anoxic spring outlets through oxygenated downstream channels. Viral abundance, virus-microbe ratios and modelled virus-microbe contact rates were lower than comparable aqueous and sedimentary environments and most similar to deep subsurface sediments. No individual cell from either spring was visibly infected. Viruses in these springs appear to play a smaller role in controlling microbial populations through lytic activity than in marine water column or surface sedimentary environments. Relief from viral predation indicates the microbial communities are primarily controlled by nutrient limitation. The similarity of these springs to deep subsurface sediments suggests a biogeographic divide in viral replication strategy in marine sediments.

Viruses at Solid-Water Interfaces: A Systematic Assessment of Interactions Driving Adsorption

Adsorption to solid-water interfaces is a major process governing the fate of waterborne viruses in natural and engineered systems. The relative contributions of different interaction forces to adsorption and their dependence on the physicochemical properties of the viruses remain, however, only poorly understood. Herein, we systematically studied the adsorption of four bacteriophages (MS2, fr, GA, and Qβ) to five model surfaces with varying surface chemistries and to three dissolved organic matter adlayers, as a function of solution pH and ionic strength, using quartz crystal microbalance with dissipation monitoring. The viruses were selected to have similar sizes and shapes but different surface charges, polarities, and topographies, as identified by modeling the distributions of amino acids in the virus capsids. Virus-sorbent interactions were governed by long-ranged electrostatics and favorable contributions from the hydrophobic effect, and shorter-ranged van der Waals interactions were of secondary importance. Steric effects depended on the topographic irregularities on both the virus and sorbent surfaces. Differences in the adsorption characteristics of the tested viruses were successfully linked to differences in their capsid surface properties. Besides identifying the major interaction forces, this work highlights the potential of computable virus surface charge and polarity descriptors to predict virus adsorption to solid-water interfaces.

Bacteriophages of Yersinia pestis

Bacteriophage play many varied roles in microbial ecology and evolution. This chapter collates a vast body of knowledge and expertise on Yersinia pestis phages, including the history of their isolation and classical methods for their isolation and identification. The genomic diversity of Y. pestis phage and bacteriophage islands in the Y. pestis genome are also discussed because all phage research represents a branch of genetics. In addition, our knowledge of the receptors that are recognized by Y. pestis phage, advances in phage therapy for Y. pestis infections, the application of phage in the detection of Y. pestis, and clustered regularly interspaced short palindromic repeats (CRISPRs) sequences of Y. pestis from prophage DNA are all reviewed here.

Viral Impact on Prokaryotic and Microalgal Activities in the Microphytobenthic Biofilm of an Intertidal Mudflat (French Atlantic Coast)

This is the first report on viriobenthos activity within the microbial biofilm located at the top-surface of the intertidal mudflat during emersion in Marennes-Oléron Bay (France). By combining in situ and ex situ approaches, the viral production (VP) was linked to the dynamics of prokaryotes and microphytobenthos (MPB). VP averaged 2–4 × 10⁸ viruses ml⁻¹ h⁻¹. VP correlated positively with the Virus to Prokaryote Ratio, and both were correlated negatively with the water content. The virus-induced mortality of prokaryotes was lower in winter than in summer (6.8 vs. 39.7% of the production) and the C-shunting may supply 2–12% of their Carbon Demand, respectively. VP accounted for 79% of loss in Prokaryotes but the response was delayed compared to the increase in VP suggesting a simultaneous release of viruses of MPB origin. This hypothesis is supported by capsid-sizing of virions by transmission electronic microscopy and bioassays. Harvesting and ex situ maintenance of top-surface sediments was carried out to monitor the dynamics of viruses, prokaryotes and MPB after inoculation with benthic or planktonic viruses. Benthic viruses modified the prokaryotic and MPB dynamics and decreased the photosynthesis efficiency in contrast to planktonic viruses that impacted MPB but not the prokaryotes.

Stability of Secondary and Tertiary Structures of Virus-Like Particles Representing Noroviruses: Effects of pH, Ionic Strength, and Temperature and Implications for Adhesion to Surfaces

Loss of ordered molecular structure in proteins is known to increase their adhesion to surfaces. The aim of this work was to study the stability of norovirus secondary and tertiary structures and its implications for viral adhesion to fresh foods and agrifood surfaces. The pH, ionic strength, and temperature conditions studied correspond to those prevalent in the principal vehicles of viral transmission (vomit and feces) and in the food processing and handling environment (pasteurization and refrigeration). The structures of virus-like particles representing GI.1, GII.4, and feline calicivirus (FCV) were studied using circular dichroism and intrinsic UV fluorescence. The particles were remarkably stable under most of the conditions. However, heating to 65°C caused losses of β-strand structure, notably in GI.1 and FCV, while at 75°C the α-helix content of GII.4 and FCV decreased and tertiary structures unfolded in all three cases. Combining temperature with pH or ionic strength caused variable losses of structure depending on the particle type. Regardless of pH, heating to pasteurization temperatures or higher would be required to increase GII.4 and FCV adhesion, while either low or high temperatures would favor GI.1 adhesion. Regardless of temperature, increased ionic strength would increase GII.4 adhesion but would decrease GI.1 adhesion. FCV adsorption would be greater at refrigeration, pasteurization, or high temperature combined with a low salt concentration or at a higher NaCl concentration regardless of temperature. Norovirus adhesion mediated by hydrophobic interaction may depend on hydrophobic residues normally exposed on the capsid surface at pH 3, pH 8, physiological ionic strength, and low temperature, while at pasteurization temperatures it may rely more on buried hydrophobic residues exposed upon structural rearrangement.

Impact of virus surface characteristics on removal mechanisms within membrane bioreactors

In this study we investigated the removal of viruses with similar size and shape but with different external surface capsid proteins by a bench-scale membrane bioreactor (MBR). The goal was to determine which virus removal mechanisms (retention by clean backwashed membrane, retention by cake layer, attachment to biomass, and inactivation) were most impacted by differences in the virus surface properties. Seven bench-scale MBR experiments were performed using mixed liquor wastewater sludge that was seeded with three lab-cultured bacteriophages with icosahedral capsids of ∼30 nm diameter (MS2, phiX174, and fr). The operating conditions were designed to simulate those at a reference, full-scale MBR facility. The virus removal mechanism most affected by virus type was attachment to biomass (removals of 0.2 log for MS2, 1.2 log for phiX174, and 3 log for fr). These differences in removal could not be explained by electrostatic interactions, as the three viruses had similar net negative charge when suspended in MBR permeate. Removals by the clean backwashed membrane (less than 1 log) and cake layer (∼0.6 log) were similar for the three viruses. A comparison between the clean membrane removals seen at the bench-scale using a virgin membrane (∼1 log), and the full-scale using 10-year old membranes (∼2-3 logs) suggests that irreversible fouling, accumulated on the membrane over years of operation that cannot be removed by cleaning, also contributes towards virus removal. This study enhances the current mechanistic understanding of virus removal in MBRs and will contribute to more reliable treatment for water reuse applications.

Behaviour and recovery of human adenovirus from tropical sediment under simulated conditions

This study assessed the contributions of pH and organic matter (OM) on the recovery of infectious human adenovirus 5 (HAdV-5) and genome copies (GCs) in waters that were artificially contaminated with tropical soil. The use of a mathematical equation was proposed based on the flocculation index of clay to assess the recovery of total GCs in these controlled assays. The results suggest that solids in the water reduced the viral genome copy loads per millilitre (GC · mL(-1)) and viral infectivity. OM did not influence the GC · mL(-1) recovery rate (p > 0.05) but led to a 99% (2 log10) reduction in plaque-forming unit counts per millilitre (PFU/mL), which indicates that infectivity and gene integrity were non-related parameters. Our findings also suggest that acidic pH levels hinder viral inactivation and that clay is the main factor responsible for the interactions of HAdV-5 with soil. These findings may be useful for future eco-epidemiological investigations and studies of viral inactivation or even as parameters for future research into water quality analysis and water treatment.

Recovery and Disinfection of Two Human Norovirus Surrogates, Feline Calicivirus and Murine Norovirus, from Hard Nonporous and Soft Porous Surfaces

Human norovirus is a leading cause of foodborne disease and can be transmitted through many routes, including environmental exposure to fomites. In this study, both the recovery and inactivation of two human norovirus surrogates, feline calicivirus (FCV) and murine norovirus (MNV), on hard nonporous surfaces (glass) and soft porous surfaces (polyester and cotton) were evaluated by both plaque assay and reverse transcription quantitative PCR method. Two disinfectants, sodium hypochlorite (8.25%) and accelerated hydrogen peroxide (AHP, at 4.25%) were evaluated for disinfection efficacy. Five coupons per surface type were used to evaluate the recovery of FCV and MNV by sonication and stomaching and the disinfection of each surface type by using 5 ml of disinfectant for a contact time of 5 min. FCV at an initial titer of ca. 7 log PFU/ml was recovered from glass, cotton, and polyester at 6.2, 5.4, and 3.8 log PFU/ml, respectively, compared with 5.5, 5.2, and 4.1 log PFU/ml, respectively, for MNV with an initial titer of ca. 6 log PFU/ml. The use of sodium hypochlorite (5,000 ppm) was able to inactivate both FCV and MNV (3.1 to 5.5 log PFU/ml) below the limit of detection on all three surface types. AHP (2,656 ppm) inactivated FCV (3.1 to 5.5 log PFU/ml) below the limit of detection for all three surface types but achieved minimal inactivation of MNV (0.17 to 1.37 log PFU/ml). Reduction of viral RNA by sodium hypochlorite corresponded to 2.72 to 4.06 log reduction for FCV and 2.07 to 3.04 log reduction for MNV on all three surface types. Reduction of viral RNA by AHP corresponded to 1.89 to 3.4 log reduction for FCV and 0.54 to 0.85 log reduction for MNV. Our results clearly indicate that both virus and surface types significantly influence recovery efficiency and disinfection efficacy. Based on the performance of our proposed testing method, an improvement in virus recovery will be needed to effectively validate virus disinfection of soft porous surfaces.

Efficacy of Coral Sand for Removal of and Bacteriophage under Saturated Flow Conditions

Knowledge of how effectively microbes are transported through porous media is useful for water resource/wastewater management. Despite much research having been done to characterize microbial contaminant transport through various sedimentary materials, very little study has been made on coral sand, such as constitutes the primary substrate of many Pacific atolls. We conducted a set of laboratory column experiments as a preliminary examination of how effective coral sand is at attenuating model pathogens J6-2 and MS2 bacteriophage (phage) under saturated flow conditions mildly representative of field conditions at the Bonriki freshwater lens, South Tarawa, Kiribati. The very poorly sorted gravelly sand coral substrate tested proved very effective at attenuating the bacterial tracer, and spatial removal rates of between 0.02 and 0.07 log cm were determined for J6-2. The ability to determine precise removal rates for MS2 phage was compromised by the use of a plastic apparatus, although the evidence weights toward coral sand being less effective at attenuating MS2 phage than it is . Further research is required to fully assess the ability of coral sand to remove pathogens and to explore how this medium could be engineered into cost-effective water/wastewater treatment solutions on Pacific atolls. The phage data from this work highlight the limitations of using plastic apparatus in experiments targeted at characterizing the fate and transport of viruses.

Zeta Potential and Aggregation of Virus-Like Particle of Human Norovirus and Feline Calicivirus Under Different Physicochemical Conditions

Although the spread of human norovirus reportedly depends on its ability to bind to food materials, the mechanism of the phenomenon remains unknown. Since protein size and electrical charge are reportedly important parameters in their adsorption, the current work is focused on determining human noroviruses isoelectric point (IEP), electrical charge and aggregate size at different pH, ionic strength (IS), and temperature. Using the baculovirus expression vector system, we produced and purified virus-like particles (VLPs) of GI.1 and GII.4 noroviruses and feline calicivirus, determined their IEP, and examined their size and electrical charge using a Zetasizer Nano ZS apparatus. Shape and size were also visualized using transmission electron microscopy. IEPs were found close to pH 4. Net charge increased as the pH deviated from the IEP. VLPs were negatively charged at all IS tested and showed a gradual decrease in charge with increasing IS. At low temperature, VLPs were 20-45 nm in diameter at pH far from their IEP and under almost all IS conditions, while aggregates appeared at or near the IEP. At increased temperatures, aggregates appeared at or near the IEP and at high IS. Aggregation at the IEP was also confirmed by microscopy. This suggests that electrostatic interactions would be the predominant factor in VLPs adhesion at pH far from 4 and at low ionic strength. In contrast, non-electrostatic interactions would prevail at around pH 4 and would be reinforced by aggregates, since size generally favors multiple bonding with sorbents.

Adsorption of Rotavirus, MS2 Bacteriophage and Surface-Modified Silica Nanoparticles to Hydrophobic Matter

Adsorption to aquifer media is an important process in the removal of viruses from groundwater. Even though hydrophobic interactions have been shown to contribute to adsorption, little is known about the hydrophobicity of viruses found in groundwater. In this study, the hydrophobicity of rotavirus, MS2 bacteriophage and DNA-labelled silica nanoparticles (SiNPs) coated with glycoprotein, protein A and alpha-1-microglobulin/bikunin precursor (AMBP) was investigated. The hydrophobicity was experimentally determined by using a modified microbial adhesion to hydrocarbons (MATH) assay. The results were compared with the theoretical hydrophobicity of the viral capsid proteins and the proteins used to coat the nanoparticles, and with the results of adsorption tests with unmodified and organosilane-coated (hydrophobic) silica sand. While most theoretical protein hydrophobicity values were similar, the results of the MATH assay suggested fundamental differences in the hydrophobicity of the viruses and the SiNPs. MS2 was found to be highly hydrophobic as based on the MATH hydrophobicity and a significantly enhanced adsorption to hydrophobic sand, whereas rotavirus was relatively hydrophilic. The MATH assay revealed that protein-coating of SiNP introduced some degree of hydrophobicity to hydrophilic SiNPs, enabling them to more closely mimic viral hydrophobicity. Our study also demonstrated that the protein-coated SiNPs better mimicked rotavirus adsorption to sand media (coated or not coated with hydrophobic organic matter) than the MS2. This further supports previous findings that these surface-modified SiNPs are useful surrogates in mimicking rotavirus retention and transport in porous media.

Interaction of human adenoviruses and coliphages with kaolinite and bentonite

Human adenoviruses (hAdVs) are pathogenic viruses responsible for public health problems worldwide. They have also been used as viral indicators in environmental systems. Coliphages (e.g., MS2, ΦX174) have also been studied as indicators of viral pollution in fecally contaminated water. Our objective was to evaluate the distribution of three viral fecal indicators (hAdVs, MS2, and ΦΧ174), between two different phyllosilicate clays (kaolinite and bentonite) and the aqueous phase. A series of static and dynamic experiments were conducted under two different temperatures (4, 25°C) for a time period of seven days. HAdV adsorption was examined in DNase I reaction buffer (pH=7.6, and ionic strength (IS)=1.4mM), whereas coliphage adsorption in phosphate buffered saline solution (pH=7, IS=2mM). Moreover, the effect of IS on hAdV adsorption under static conditions was evaluated. The adsorption of hAdV was assessed by real-time PCR and its infectivity was tested by cultivation methods. The coliphages MS2 and ΦΧ174 were assayed by the double-layer overlay method. The experimental results have shown that coliphage adsorption onto both kaolinite and bentonite was higher for the dynamic than the static experiments; whereas hAdV adsorption was lower under dynamic conditions. The adsorption of hAdV increased with decreasing temperature, contrary to the results obtained for the coliphages. This study examines the combined effect of temperature, agitation, clay type, and IS on hAdV adsorption onto clays. The results provide useful new information on the effective removal of viral fecal indicators (MS2, ΦX174 and hAdV) from dilute aqueous solutions by adsorption onto kaolinite and bentonite. Factors enabling enteric viruses to penetrate soils, groundwater and travel long distances within aquifers are important public health issues. Because the observed adsorption behavior of surrogate coliphages MS2 and ΦΧ174 is substantially different to that of hAdV, neither MS2 nor ΦΧ174 is recommended as a suitable model for adenovirus.

Removal properties of human enteric viruses in a pilot-scale membrane bioreactor (MBR) process

In order to evaluate removal properties of human enteric viruses from wastewater by a membrane bioreactor (MBR), influent, anoxic and oxic mixed liquor, and membrane effluent samples were collected in a pilot-scale anoxic-oxic MBR process for 16 months, and concentrations of enteroviruses, norovirus GII, and sapoviruses were determined by real-time PCR using murine norovirus as a process control. Mixed liquor samples were separated into liquid and solid phases by centrifugation, and viruses in the bulk solution and those associated with mixed liquor suspended solids (MLSS) were quantified. Enteroviruses, norovirus GII, and sapoviruses were detected in the influent throughout the sampling period (geometrical mean, 4.0, 3.1, and 4.4 log copies/mL, respectively). Enterovirus concentrations in the solid phase of mixed liquor were generally lower than those in the liquid phase, and the mean log reduction value between influent and anoxic mixed liquor was 0.40 log units. In contrast, norovirus GII and sapovirus concentrations in the solid phase were equal to or higher than those in the liquid phase, and higher log reduction values (1.3 and 1.1 log units, respectively) were observed between influent and anoxic mixed liquor. This suggested that enteroviruses were less associated with MLSS than norovirus GII and sapoviruses, resulting in lower enterovirus removal in the activated sludge process. Enteroviruses and norovirus GII were detected in the MBR effluent but sapoviruses were not in any effluent samples. When MLSS concentration was reduced to 50-60% of a normal operation level, passages of enteroviruses and norovirus GII through a PVDF microfiltration membrane were observed. Since rejection of viruses by the membrane was not related to trans-membrane pressure which was monitored as a parameter of membrane fouling, the results indicated that adsorption to MLSS plays an important role in virus removal by an MBR, and removal properties vary by viruses reflecting different adsorptive behavior to MLSS. Our observations suggested that sapoviruses are more associated with MLSS and removed more efficiently than enteroviruses and norovirus GII.

A review of virus removal in wastewater treatment pond systems

Wastewater treatment ponds (lagoons) are one of the most common types of technologies used for wastewater management worldwide, especially in small cities and towns. They are particularly well-suited for systems where the effluent is reused for irrigation. However, the efficiency of virus removal in wastewater treatment pond systems is not very well understood. The main objective of this paper is to critically review the major findings related to virus removal in wastewater treatment pond systems and to statistically analyze results reported in the literature from field studies on virus removal in these systems. A comprehensive analysis of virus removal reported in the literature from 71 different wastewater treatment pond systems reveals only a weak to moderate correlation of virus removal with theoretical hydraulic retention time. On average, one log10 reduction of viruses was achieved for every 14.5-20.9 days of retention, but the 95th percentile value of the data analyzed was 54 days. The mechanisms responsible for virus removal in wastewater treatment ponds were also reviewed. One recent finding is that sedimentation may not be a significant virus removal mechanism in some wastewater ponds. Recent research has also revealed that direct and indirect sunlight-mediated mechanisms are not only dependent on pond water chemistry and optics, but also on the characteristics of the virus and its genome. MS2 coliphage is considered to be the best surrogate for studying sunlight disinfection in ponds. The interaction of viruses with particles, with other microorganisms, and with macroinvertebrates in wastewater treatment ponds has not been extensively studied. It is also unclear whether virus internalization by higher trophic-level organisms has a protective or a detrimental effect on virus viability and transport in pond systems. Similarly, the impact of virus-particle associations on sunlight disinfection in ponds is not well understood. Future research should focus on the interactions of viruses with particles and with other organisms, as well as the development of a model for virus removal in pond systems that can be used for design purposes, and to inform future editions of the WHO Guidelines for Wastewater Use in Agriculture.

Sunlight inactivation of viruses in open-water unit process treatment wetlands: modeling endogenous and exogenous inactivation rates

Sunlight inactivation is an important mode of disinfection for viruses in surface waters. In constructed wetlands, for example, open-water cells can be used to promote sunlight disinfection and remove pathogenic viruses from wastewater. To aid in the design of these systems, we developed predictive models of virus attenuation that account for endogenous and exogenous sunlight-mediated inactivation mechanisms. Inactivation rate models were developed for two viruses, MS2 and poliovirus type 3; laboratory- and field-scale experiments were conducted to evaluate the models' ability to estimate inactivation rates in a pilot-scale, open-water, unit-process wetland cell. Endogenous inactivation rates were modeled using either photoaction spectra or total, incident UVB irradiance. Exogenous inactivation rates were modeled on the basis of virus susceptibilities to singlet oxygen. Results from both laboratory- and field-scale experiments showed good agreement between measured and modeled inactivation rates. The modeling approach presented here can be applied to any sunlit surface water and utilizes easily measured inputs such as depth, solar irradiance, water matrix absorbance, singlet oxygen concentration, and the virus-specific apparent second-order rate constant with singlet oxygen (k2). Interestingly, the MS2 k2 in the open-water wetland was found to be significantly larger than k2 observed in other waters in previous studies. Examples of how the model can be used to design and optimize natural treatment systems for virus inactivation are provided.

Comparison of methods for evaluating the thermal stability of human enteric viruses

Human enteric viruses have been identified as one of the predominant causative agents of food-borne illnesses in developed countries, and it is estimated that human norovirus accounts for a majority of these illnesses each year. Not all of these viruses can be cultured and hence relatively little is known about their pathogenesis and physicochemical properties. To overcome this, researchers have utilized different virus surrogates for the study of non-cultivable human enteric viruses. In this review, we discuss various methods utilized for the evaluation of the thermal stability of human enteric viruses, compare the results of these methods, and examine how researchers may move toward a single standard approach (i.e., temperatures, virus concentrations, volume/weight of matrices, etc.) for determining thermal inactivation profiles of human enteric viruses and their surrogates. Based on our review, we found that temperature, time of exposure, type of matrix, analysis type, type of heat application, and the concentration and volume of virus used in the experiments were highly variable across virus surrogates even for the same surrogates. Because of these differences-along with the inherent limitations of using surrogate viruses-comparison of these methods and how the results may be extrapolated to human enteric viruses is quite challenging. As a result, we discuss how researchers may move toward a single standard approach for determining thermal inactivation profiles of human enteric viruses and their surrogates.

Transport of Human Adenoviruses in Water Saturated Laboratory Columns

Groundwater may be contaminated with infective human enteric viruses from various wastewater discharges, sanitary landfills, septic tanks, agricultural practices, and artificial groundwater recharge. Coliphages have been widely used as surrogates of enteric viruses, because they share many fundamental properties and features. Although a large number of studies focusing on various factors (i.e. pore water solution chemistry, fluid velocity, moisture content, temperature, and grain size) that affect biocolloid (bacteria, viruses) transport have been published over the past two decades, little attention has been given toward human adenoviruses (hAdVs). The main objective of this study was to evaluate the effect of pore water velocity on hAdV transport in water saturated laboratory-scale columns packed with glass beads. The effects of pore water velocity on virus transport and retention in porous media was examined at three pore water velocities (0.39, 0.75, and 1.22 cm/min). The results indicated that all estimated average mass recovery values for hAdV were lower than those of coliphages, which were previously reported in the literature by others for experiments conducted under similar experimental conditions. However, no obvious relationship between hAdV mass recovery and water velocity could be established from the experimental results. The collision efficiencies were quantified using the classical colloid filtration theory. Average collision efficiency, α, values decreased with decreasing flow rate, Q, and pore water velocity, U, but no significant effect of U on α was observed. Furthermore, the surface properties of viruses and glass beads were used to construct classical DLVO potential energy profiles. The results revealed that the experimental conditions of this study were unfavorable to deposition and that no aggregation between virus particles is expected to occur. A thorough understanding of the key processes governing virus transport is pivotal for public health protection.

Nano-structured surface modification of micro-porous ceramic membrane with positively charged nano-Y2O3coating for organic dyes removal

Through dip-coating and thermal decomposition process, the positively charged ceramic membrane was successfully prepared for negative organic dyes removal.

Relative insignificance of virus inactivation during aluminum electrocoagulation of saline waters

Combined removal and inactivation of the MS2 bacteriophage from model saline (0-100 mM NaCl) waters by electrochemical treatment using a sacrificial aluminum anode was evaluated. Both chemical and electrodissolution contributed to coagulant dosing since measured aluminum concentrations were statistically higher than purely electrochemical predictions using Faraday's law. Electrocoagulation generated only small amounts of free chlorine in situ but effectively destabilized viruses and incorporated them into Al(OH)3(s) flocs during electrolysis. Low chlorine concentrations combined with virus shielding and aggregation within flocs resulted in very slow disinfection rates necessitating extended flocculation/contact times to achieve significant log-inactivation. Therefore, the dominant virus control mechanism during aluminum electrocoagulation of saline waters is "physical" removal by uptake onto flocs rather than "chemical" inactivation by chlorine. Attenuated total reflectance-Fourier transform infrared spectroscopy provided evidence for oxidative transformations of capsid proteins including formation of oxyacids, aldehydes, and ketones. Electrocoagulation significantly altered protein secondary structures decreasing peak areas associated with turns, bends, α-helices, β-structures, and random coils for inactivated viruses compared with the MS2 stock. Quantitative reverse transcription polymerase chain reaction (qRT-PCR) measurements showed rapid initial RNA damage following a similar trend as plaque assay measurements of infectious viruses. However, ssRNA cleavage measured by qRT-PCR underestimated inactivation over longer durations. Although aluminum electrocoagulation of saline waters disorders virus capsids and damages RNA, inactivation occurs at a sufficiently low rate so as to only play a secondary role to floc-encapsulation during residence times typical of electrochemical treatment.

Dynamic attachment of Chlorovirus PBCV-1 to Chlorella variabilis

Chloroviruses infect their hosts by specifically binding to and degrading the cell wall of their algal hosts at the site of attachment, using an intrinsic digesting enzyme(s). Chlorovirus PBCV-1 stored as a lysate survived longer than virus alone, suggesting virus attachment to cellular debris may be reversible. Ghost cells (algal cells extracted with methanol) were used as a model to study reversibility of PBCV-1 attachment because ghost cells are as susceptible to attachment and wall digestion as are live cells. Reversibility of attachment to ghost cells was examined by releasing attached virions with a cell wall degrading enzyme extract. The majority of the released virions retained infectivity even after re-incubating the released virions with ghost cells two times. Thus the chloroviruses appear to have a dynamic attachment strategy that may be beneficial in indigenous environments where cell wall debris can act as a refuge until appropriate host cells are available.

Development of a novel filter cartridge system with electropositive granule media to concentrate viruses from large volumes of natural surface water

Exposure to various infectious viruses in environmental drinking water can constitute a public health risk. However, it is difficult to detect viruses in water due to their low concentration. In this study, we have developed a novel filter cartridge system containing electropositive granule media (EGM). Viruses present in large volumes of environmental samples were adsorbed onto the EGM, and then recovered by elution and poly(ethylene glycol) (PEG) concentration. To evaluate the system's efficiency in viral recovery, poliovirus (PV-1), a surrogate for enteric viruses, was used to artificially contaminate river water samples which were then assayed by quantitative real-time PCR. To optimize the concentration procedure, the eluent type, water flow rate and properties (e.g., pH, bacterial, and viral loads), were evaluated. The highest virus recovery was obtained by pumping river water at a flow rate of 300 mL/min and then pushing 3 L of an eluent containing 3× broth [1.5% (w/v) NaCl, 3% (w/v) tryptone, 1.5% (w/v) beef powder] with 0.05 mol/L glycine through the filter. Using this procedure, the recovery efficiencies of PV-1 from 10 to 100 L of spiked river water were up to 99%. In addition, this method is virus load and pH dependent. Virus recovery was maximal at a load of between 10(3.5) and 10(5.5) TCID50 and a pH ranging from 5 to 7. The bacterial load in the water has no effect on virus recovery. Different types of viruses and surface water were tested to validate the system's applicability. Results revealed that the EGM filter cartridge was able to concentrate PV-1, human adenoviruses (HAdVs) and noroviruses (HuNoVs) with high efficiency from river, lake, and reservoir water. Furthermore, it showed more efficient recovery than glass wool and 1MDS filters. These data suggest that this system provides rapid and efficient virus recovery from a large volume of natural surface water and, as such, could be a useful tool in revealing the presence of viruses in surface water.

Concentration of enteric viruses from tap water using an anion exchange resin-based method

Detecting low concentrations of enteric viruses in water is needed for public health-related monitoring and control purposes. Thus, there is a need for sensitive, rapid and cost effective enteric viral concentration methods compatible with downstream molecular detection. Here, a virus concentration method based on adsorption of the virus to an anion exchange resin and direct isolation of nucleic acids is presented. Ten liter samples of tap water spiked with different concentrations (10-10,000 TCID50/10 L) of human adenovirus 40 (HAdV-40), hepatitis A virus (HAV) or rotavirus (RV) were concentrated and detected by real time PCR or real time RT-PCR. This method improved viral detection compared to direct testing of spiked water samples where the ΔCt was 12.1 for AdV-40 and 4.3 for HAV. Direct detection of RV in water was only possible for one of the three replicates tested (Ct of 37), but RV detection was improved using the resin method (all replicates tested positive with an average Ct of 30, n=3). The limit of detection of the method was 10 TCID50/10 L for HAdV-40 and HAV, and 100 TCID50/10 L of water for RV. These results compare favorably with detection limits reported for more expensive and laborious methods.

Function of bacterial cells and their exuded extracellular polymeric substances (EPS) in virus removal by red soils

The potential influence of autochthonous microorganisms on virus fate in soil is usually determined through extreme conditions of sterilization vs. nonsterilization; however, the relative importance of microbial cells and their exudates remains unclear. In this study, bacterial cells (cell) were harvested, and their exuded extracellular polymeric substances (EPS) were extracted from three strains of bacteria, namely, Gram-negative bacteria Pseudomonas putida and Pseudomonas aeruginosa as well as Gram-positive bacterium Bacillus subtilis. This study aimed to evaluate virus removal in solutions in the presence of cell, EPS, and their combination (cell/EPS), as well as to investigate how their presence affects virus removal efficiencies by four red soils based on batch experiments. Results showed that virus removal percentage in solutions ranged from 11 to 23 in the presence of cells only and from 12 to 15 in the presence of EPS only. The removal percentage in the combined cell/EPS treatment can be estimated by summing the results achieved by the cell and EPS treatments, separately. Meanwhile, cell presence had a negligible effect on virus removal by red soils. EPS and combined cell/EPS significantly reduced virus removal by 20 to 69% and 16 to 50%, respectively, which indicated that EPS served a dominant function in reducing virus removal. This study clearly demonstrated that the prediction of virus removal by red soils must consider the effect of bacteria, especially those producing large quantities of EPS, which can be responsible for the underestimation of viral load in certain studies.

Virus removal and inactivation by iron (hydr)oxide-mediated Fenton-like processes under sunlight and in the dark

Advanced oxidation processes (AOPs) have emerged as a promising alternative to conventional disinfection methods to control microbial water quality, yet little is known about the fate of viruses in AOPs. In this study, we investigated the fate of MS2 coliphage in AOPs that rely on heterogeneous Fenton-like processes catalyzed by iron (hydr)oxide particles. Both physical removal of viruses from solution via adsorption onto particles as well as true inactivation were considered. Virus fate was studied in batch reactors at circumneutral pH, containing 200 mg L(-1) of four different commercial iron (hydr)oxide particles of similar mesh sizes: hematite (α-Fe2O3), goethite (α-FeOOH), magnetite (Fe3O4) and amorphous iron(iii) hydroxide (Fe(OH)3). The effect of adsorption and sunlight exposure on the survival of MS2 was considered. On a mass basis, all particles exhibited a similar virus adsorption capacity, whereas the rate of adsorption followed the order FeOOH > Fe2O3 > Fe3O4 ≈ Fe(OH)3. This adsorption behavior could not be explained by electrostatic considerations; instead, adsorption must be governed by other factors, such as hydrophobic interactions or van der Waals forces. Adsorption to three of the particles investigated (α-FeOOH, Fe3O4, Fe(OH)3) caused virus inactivation of 7%, 22%, and 14%, respectively. Exposure of particle-adsorbed viruses to sunlight and H2O2 resulted in efficient additional inactivation, whereas inactivation was negligible for suspended viruses. The observed first-order inactivation rate constants were 6.6 × 10(-2), 8.7 × 10(-2), 0.55 and 1.5 min(-1) for α-FeOOH, α-Fe2O3, Fe3O4 and Fe(OH)3 respectively. In the absence of sunlight or H2O2, no inactivation was observed beyond that caused by adsorption alone, except for Fe3O4, which caused virus inactivation via a dark Fenton-like process. Overall our results demonstrate that heterogeneous Fenton-like processes can both physically remove viruses from water as well as inactivate them via adsorption and via a particle-mediated (photo-)Fenton-like process.

Thermal treatment for pathogen inactivation as a risk mitigation strategy for safe recycling of organic waste in agriculture

Thermal treatment at temperatures between 46.0°C and 55.0°C was evaluated as a method for sanitization of organic waste, a temperature interval less commonly investigated but important in connection with biological treatment processes. Samples of dairy cow feces inoculated with Salmonella Senftenberg W775, Enterococcus faecalis, bacteriophage ϕX174, and porcine parvovirus (PPV) were thermally treated using block thermostats at set temperatures in order to determine time-temperature regimes to achieve sufficient bacterial and viral reduction, and to model the inactivation rate. Pasteurization at 70°C in saline solution was used as a comparison in terms of bacterial and viral reduction and was proven to be effective in rapidly reducing all organisms with the exception of PPV (decimal reduction time of 1.2 h). The results presented here can be used to construct time-temperature regimes in terms of bacterial inactivation, with D-values ranging from 0.37 h at 55°C to 22.5 h at 46.0°C and 0.45 h at 55.0°C to 14.5 h at 47.5°C for Salmonella Senftenberg W775 and Enterococcus faecalis, respectively and for relevant enteric viruses based on the ϕX174 phage with decimal reduction times ranging from 1.5 h at 55°C to 16.5 h at 46°C. Hence, the study implies that considerably lower treatment temperatures than 70°C can be used to reach a sufficient inactivation of bacterial pathogens and potential process indicator organisms such as the ϕX174 phage and raises the question whether PPV is a valuable process indicator organism considering its extreme thermotolerance.

Transfer efficiency of bacteria and viruses from porous and nonporous fomites to fingers under different relative humidity conditions

Fomites can serve as routes of transmission for both enteric and respiratory pathogens. The present study examined the effect of low and high relative humidity on fomite-to-finger transfer efficiency of five model organisms from several common inanimate surfaces (fomites). Nine fomites representing porous and nonporous surfaces of different compositions were studied. Escherichia coli, Staphylococcus aureus, Bacillus thuringiensis, MS2 coliphage, and poliovirus 1 were placed on fomites in 10-μl drops and allowed to dry for 30 min under low (15% to 32%) or high (40% to 65%) relative humidity. Fomite-to-finger transfers were performed using 1.0 kg/cm(2) of pressure for 10 s. Transfer efficiencies were greater under high relative humidity for both porous and nonporous surfaces. Most organisms on average had greater transfer efficiencies under high relative humidity than under low relative humidity. Nonporous surfaces had a greater transfer efficiency (up to 57%) than porous surfaces (<6.8%) under low relative humidity, as well as under high relative humidity (nonporous, up to 79.5%; porous, <13.4%). Transfer efficiency also varied with fomite material and organism type. The data generated can be used in quantitative microbial risk assessment models to assess the risk of infection from fomite-transmitted human pathogens and the relative levels of exposure to different types of fomites and microorganisms.

Silica decorated TiO2 for virus inactivation in drinking water--simple synthesis method and mechanisms of enhanced inactivation kinetics

A new method of modifying TiO2 photocatalysts with SiO2 is developed in which SiO2 nanoparticles are simply mixed with TiO2 in water under ambient conditions. This method does not require the use of toxic solvents or significant energy input. Although the SiO2 modification slightly reduces hydroxyl free radical production, the composite SiO2-TiO2 nanomaterials have markedly higher photocatalytic inactivation rates for a common surrogate virus, bacteriophage MS2 (up to 270% compared to the unmodified TiO2), due to the greatly improved adsorptive density and dark inactivation of MS2. The Langmuir isotherm describes the adsorption data well and shows that the TiO2 modified with 5% SiO2 has a maximum adsorption density qmax 37 times that of the unmodified TiO2. The Langmuir-Hinshelwood model fits the photocatalytic inactivation kinetic data well. The SiO2-TiO2 material produces a greater maximum initial inactivation rate yet a lower intrinsic surface reaction rate constant, consistent with the reduced hydroxyl radical production and enhanced adsorption. These results suggest that modifying photocatalyst surface to increase contaminant adsorption is an important strategy to improve photocatalytic reaction efficiency. Simple and cheap synthesis methods such as that used in this study bring photocatalysis closer to being a viable water treatment option.

Comparison of spike and aerosol challenge tests for the recovery of viable influenza virus from non-woven fabrics

BACKGROUND

To experimentally determine the survival kinetics of influenza virus on personal protective equipment (PPE) and to evaluate the risk of virus transfer from PPE, it is important to compare the effects on virus recovery of the method used to contaminate the PPE with virus and the type of eluent used to recover it.

METHODS

Avian influenza virus (AIV) was applied as a liquid suspension (spike test) and as an aerosol to three types of non-woven fabrics [polypropylene (PP), polyester (PET), and polyamide (Nylon)] that are commonly used in the manufacture of PPE. This was followed by virus recovery using eight different eluents (phosphate-buffered saline, minimum essential medium, and 1.5% or 3.0% beef extract at pH 7, 8, or 9).

RESULTS

For spike tests, no statistically significant difference was found in virus recovery using any of the eluents tested. Hydrophobic surfaces (PP and PET) yielded higher spiked virus recovery than hydrophilic Nylon. From all materials, the virus recovery was much lower in aerosol challenge tests than in spike tests.

CONCLUSIONS

Significant differences were found in the recovery of viable AIV from non-woven fabrics between spike and aerosol challenge tests. The findings of this study demonstrate the need for realistic aerosol challenge tests rather than liquid spike tests in studies of virus survival on surfaces where airborne transmission of influenza virus may get involved.

Natural persistence of food- and waterborne viruses

This chapter summarises data on the persistence of food-and waterborne viruses in the natural environment and discusses the different factors which can affect this persistence. Conventional and alternative methods by which persistence can be studied are described, and the natural factors influencing virus persistence outside the host organism are discussed. Available data concerning virus persistence in water, soil, on surfaces and in food products are reviewed.

Biotin- and glycoprotein-coated microspheres: potential surrogates for studying filtration of cryptosporidium parvum in porous media

Cryptosporidium parvum is a waterborne pathogen, yet no suitable surrogate has been established for quantifying its filtration removal in porous media. Carboxyl polystyrene microspheres with size, density, and shape similar to C. parvum were coated with biotin (free and containing amine, NH(2)) and glycoprotein. These biomolecules have isoelectric points similar to C. parvum (pH ≈ 2), and glycoprotein is a major type of surface protein that oocysts possess. Zeta potential (ζ) and filtration removal of particles in sand of two different grain sizes were examined. Compared to unmodified microspheres, modified microspheres achieved a superior match to the oocysts in ζ, concentration, mass recovery, and collision coefficient. They showed the same log reduction in concentration as oocysts, whereas results from unmodified microspheres deviated by 1 order of magnitude. Of the three types of modified microspheres, glycoprotein-coated microspheres best resembled oocyst concentration, despite having ζ similar to NH(2)-biotin-coated microspheres, suggesting that surface protein also played an important role in particle attachment on solid surfaces. With further validation in environmental conditions, the surrogates developed here could be a cost-effective new tool for assessing oocyst filtration in porous media, for example, to evaluate the performance of sand filters in water and wastewater treatment, water recycling through riverbank filtration, and aquifer recharge.

Influence of inorganic ions on aggregation and adsorption behaviors of human adenovirus

In this study, we investigated the influence of inorganic ions on the aggregation and deposition (adsorption) behavior of human adenovirus (HAdV). Experiments were conducted to determine the surface charge and size of HAdV and viral adsorption capacity of sand in different salt conditions. The interfacial potential energy was calculated using extended Derjaguin and Landau, Verwey and Overbeek (XDLVO) and steric hindrance theories to interpret the experimental results. Results showed that different compositions of inorganic ions have minimal effect on varying the iso-electric point pH (pH(iep)) of HAdV (ranging from 3.5 to 4.0). Divalent cations neutralized/shielded virus surface charge much more effectively than monovalent cations at pH above pH(iep). Consequently, at neutral pH the presence of divalent cations enhanced the aggregation of HAdV as well as its adsorption to sand. Aggregation and adsorption behaviors generally agreed with XDLVO theory; however, in the case of minimal electrostatic repulsion, steric force by virus' fibers can increase the energy barrier and distance of secondary minimum, resulting in limited aggregation and deposition. Overall, our results indicated that subsurface water with low hardness residing in sandy soils may have a higher potential of being contaminated by HAdV.

Virus inactivation in the presence of quartz sand under static and dynamic batch conditions at different temperatures

Virus inactivation is one of the most important factors that controls virus fate and transport in the subsurface. In this study the inactivation of viruses in the presence of quartz sand was examined. The bacteriophages MS2 and ΦX174 were used as model viruses. Experiments were performed at 4°C and 20°C, under constant controlled conditions, to investigate the effect of virus type, temperature, sand size, and initial virus concentration on virus inactivation. The experimental virus inactivation data were satisfactorily represented by a pseudo-first order expression with time-dependent rate coefficients. Furthermore, the results indicated that virus inactivation was substantially affected by the ambient temperature and initial virus concentration. The inactivation rate of MS2 was shown to be greater than that of ΦX174. However, the greatest inactivation was observed for MS2 without the presence of sand, at 20°C. Sand surfaces offered protection against inactivation especially under static conditions. However, no obvious relationship between sand particle size and virus inactivation could be established from the experimental data. Moreover, the inactivation rates were shown to increase with decreasing virus concentration.