Biocides in hydraulic fracturing fluids: a critical review of their usage, mobility, degradation, and toxicity

A Generic Method for Predicting Environmental Concentrations of Hydraulic Fracturing Chemicals in Soil and Shallow Groundwater

Source-pathway-receptor analyses involving solute migration pathways through soil and shallow groundwater are typically undertaken to assess how people and the environment could come into contact with chemicals associated with coal seam gas operations. For the potential short-term and long-term release of coal seam gas fluids from storage ponds, solute concentration and dilution factors have been calculated using a water flow and solute transport modelling framework for an unsaturated zone-shallow groundwater system. Uncertainty about dilution factors was quantified for a range of system parameters: (i) leakage rates from storage ponds combined with recharge rates, (ii) a broad combination of soil and groundwater properties, and (iii) a series of increasing travel distances through soil and groundwater. Calculated dilution factors in the soil increased from sand to loam soil and increased with an increasing recharge rate, while dilution decreased for a decreasing leak rate and leak duration. In groundwater, dilution factors increase with increasing aquifer hydraulic conductivity and riverbed conductance. For a hypothetical leak duration of three years, the combined soil and groundwater dilution factors are larger than 6980 for more than 99.97% of bores that are likely to be farther than 100 m from the source. Dilution factors were more sensitive to uncertainty in leak rates than recharge rates. Based on this dilution factor, a comparison of groundwater predicted environmental concentrations and predicted no-effect concentrations for a subset of hydraulic fracturing chemicals used in Australia revealed that for all but two of the evaluated chemicals the estimated groundwater concentration (for a hypothetical water bore at 100 m from the solute source) is smaller than the no-effect concentration for the protection of aquatic ecosystems.

Nutrient Level Determines Biofilm Characteristics and Subsequent Impact on Microbial Corrosion and Biocide Effectiveness

The impact that nutrient level has on biofilm characteristics, biocide effectiveness, and the associated risk of microbiologically influenced corrosion (MIC) was assessed using multispecies biofilms from two different oilfield consortia. A range of microbiological, microscopy, and corrosion methods demonstrated that the continuous flow of nutrients for the microbial growth resulted in higher activity, thickness, and robustness of the biofilms formed on carbon steel, which induced greater localized corrosion compared to biofilms formed under batch, nutrient-depleted conditions. Despite of the differences in biofilm characteristics, biofilms displayed comparable susceptibilities to glutaraldehyde biocide, with similar log10 reductions and percent reductions of microorganisms under both nutrient conditions. Nevertheless, nutrient replenishment impacted the effectiveness of the biocide in controlling microbial populations; a higher concentration of cells survived the biocide treatment in biofilms formed under a continuous flow of nutrients. Complementary DNA-/RNA-based amplicon sequencing and bioinformatics analysis were used to discriminate the active within the total populations in biofilms established at the different nutrient conditions and allowed the identification of the microbial species that remained active despite nutrient depletion and biocide treatment. Detection of persistent active microorganisms after exposure to glutaraldehyde, regardless of biofilm structure, suggested the presence of microorganisms less susceptible to this biocide and highlighted the importance of monitoring active microbial species for the early detection of biocide resistance in oil production facilities.IMPORTANCE Microbiologically influenced corrosion (MIC) is a complex process that generates economic losses to the industry every year. Corrosion must be managed to prevent a loss of containment of produced fluids to the external environment. MIC management includes the identification of assets with higher MIC risk, which could be influenced by nutrient levels in the system. Assessing biofilms under different nutrient conditions is essential for understanding the impact of flow regime on microbial communities and the subsequent impact on microbial corrosion and on the effectiveness of biocide treatment. This investigation simulates closely oil production systems, which contain piping sections exposed to continuous flow and sections that remain stagnant for long periods. Therefore, the results reported here are useful for MIC management and prevention. Moreover, the complementary methodological approach applied in this investigation highlighted the importance of implementing RNA-based methods for better identification of active microorganisms that survive stress conditions in oil systems.

Non-target screening reveals the mechanisms responsible for the antagonistic inhibiting effect of the biocides DBNPA and glutaraldehyde on benzoic acid biodegradation

The desalination and reuse of discharged cooling tower water (CTW) as feed water for the cooling tower could lower the industrial fresh water withdrawal. A potential pre-treatment method before CTW desalination is the use of constructed wetlands (CWs). Biodegradation is an important removal mechanism in CWs. In the present study, the impact of the biocides 2,2-dibromo-2-cyanoacetamide (DBNPA) and glutaraldehyde on the biodegradation process by CW microorganisms was quantified in batch experiments in which benzoic acid was incubated with realistic CTW biocide concentrations. DBNPA had a stronger negative impact on the biodegradation than glutaraldehyde. The combination of DBNPA and glutaraldehyde had a lower impact on the biodegradation than DBNPA alone. UHPLC-qTOF-MS/MS non-target screening combined with data-analysis script 'patRoon' revealed two mechanisms behind this low impact. Firstly, the presence of glutaraldehyde resulted in increased DBNPA transformation to the less toxic transformation product 2-bromo-2-cyanoacetamide (MBNPA) and newly discovered 2,2-dibromopropanediamide. Secondly, the interaction between glutaraldehyde and DBNPA resulted in the formation of new products that were less toxic than DBNPA. The environmental fate and toxicity of these products are still unknown. Nevertheless, their formation can have important implications for the simultaneous use of the biocides DBNPA and glutaraldehyde for a wide array of applications.

Geochemical and microbial characterizations of flowback and produced water in three shale oil and gas plays in the central and western United States

Limited understanding of wastewater streams produced from shale oil and gas wells impedes best practices of wastewater treatment and reuse. This study provides a comprehensive and comparative analysis of flowback and produced water from three major and newly developed shale plays (the Bakken shale, North Dakota; the Barnett shale, Texas; and the Denver-Julesburg (DJ) basin, Colorado) in central and western United States. Geochemical features that included more than 10 water quality parameters, dissolved organic matter, as well as microbial community structures were characterized and compared. Results showed that wastewater from Bakken and Barnett shales has extremely high salinity (∼295 g/L total dissolved solids (TDS)) and low organic concentration (80-252 mg/L dissolved organic carbon (DOC)). In contrast, DJ basin showed an opposite trend with low TDS (∼30 g/L) and high organic content (644 mg/L DOC). Excitation-emission matrix (EEM) fluorescence spectra demonstrated that more humic acid and fluvic acid-like organics with higher aromaticity existed in Bakken wastewater than that in Barnett and DJ basin. Microbial communities of Bakken samples were dominated by Fe (III)-reducing bacteria Geobacter, lactic acid bacteria Lactococcus and Enterococcus, and Bradyrhizobium, while DJ basin water showed higher abundance of Rhodococcus, Thermovirga, and sulfate reducing bacteria Thermotoga and Petrotoga. All these bacteria are capable of hydrocarbon degradation. Hydrogenotrophic methanogens dominated the archaeal communities in all samples.

Continuing Impacts of Selective Inhibition on Bacterial and Fungal Communities in an Agricultural Soil

Selective inhibition (SI) has been routinely used to differentiate the contributions of bacteria and fungi to soil ecological processes. SI experiments typically measured rapid responses within hours since the addition of inhibitor, but the long-term effects of selective biocides on microbial community composition and function were largely unknown. In this study, a microcosm experiment was performed with an agricultural soil to explore the effectiveness of two bactericides (bronopol, streptomycin) and two fungicides (cycloheximide, captan), which were applied at two different concentrations (2 and 10 mg g^-1). The microcosms were incubated for 6 weeks. A radiolabeled substrate, [1,2,3,4,4a,9a-¹⁴C] anthracene, was spiked to all microcosms, and the derived CO₂ was monitored during the incubation. The abundance and composition of bacteria and fungi were assessed by qPCR and Miseq sequencing of ribosomal rRNA genes. It was demonstrated that only 2 mg g^-1 bronopol and cycloheximide significantly changed the bacteria to fungi ratio without apparent non-target inhibition on the abundances; however, community shifts were observed in all treatments after 6 weeks incubation. The enrichment of specific taxa implicated a selection of resistant or adapted microbes by these biocides. Mineralization of anthracene was continuingly suppressed in all SI microcosms, which may result in biased estimate of bacterial and fungal contributions to pollutant degradation. These findings highlight the risks of long-term application of selective inhibition, and a preliminary assessment of biocide selection and concentration is highly recommended.

Unconventional Oil and Gas Energy Systems: An Unidentified Hotspot of Antimicrobial Resistance?

Biocides used in unconventional oil and gas (UOG) practices, such as hydraulic fracturing, control microbial growth. Unwanted microbial growth can cause gas souring, pipeline clogging, and microbial-induced corrosion of equipment and transportation pipes. However, optimizing biocide use has not been a priority. Moreover, biocide efficacy has been questioned because microbial surveys show an active microbial community in hydraulic fracturing produced and flowback water. Hydraulic fracturing produced and flowback water increases risks to surface aquifers and rivers/lakes near the UOG operations compared with conventional oil and gas operations. While some biocides and biocide degradation products have been highlighted as chemicals of concern because of their toxicity to humans and the environment, the selective antimicrobial pressure they cause has not been considered seriously. This perspective article aims to promote research to determine if antimicrobial pressure in these systems is cause for concern. UOG practices could potentially create antimicrobial resistance hotspots under-appreciated in the literature, practice, and regulation arena, hotspots that should not be ignored. The article is distinctive in discussing antimicrobial resistance risks associated with UOG biocides from a biological risk, not a chemical toxicology, perspective. We outline potential risks and highlight important knowledge gaps that need to be addressed to properly incorporate antimicrobial resistance emergence and selection into UOG environmental and health risk assessments.

Surface Water Microbial Community Response to the Biocide 2,2-Dibromo-3-Nitrilopropionamide, Used in Unconventional Oil and Gas Extraction

Unconventional oil and gas activity can affect pH, total organic carbon, and microbial communities in surface water, altering their ability to respond to new environmental and/or anthropogenic perturbations. These findings demonstrate that 2,2-dibromo-3-nitrilopropionamide (DBNPA), a common hydraulic fracturing (HF) biocide, affects microbial communities differently as a consequence of past HF exposure, persisting longer in HF-impacted (HF+) waters. These findings also demonstrate that DBNPA has low efficacy in environmental microbial communities regardless of HF impact. These findings are of interest, as understanding microbial responses is key for formulating remediation strategies in unconventional oil and gas (UOG)-impacted environments. Moreover, some DBNPA degradation by-products are even more toxic and recalcitrant than DBNPA itself, and this work identifies novel brominated degradation by-products formed.

Production of unconventional oil and gas continues to rise, but the effects of high-density hydraulic fracturing (HF) activity near aquatic ecosystems are not fully understood. A commonly used biocide in HF, 2,2-dibromo-3-nitrilopropionamide (DBNPA), was studied in microcosms of HF-impacted (HF+) versus HF-unimpacted (HF−) surface water streams to (i) compare the microbial community response, (ii) investigate DBNPA degradation products based on past HF exposure, and (iii) compare the microbial community response differences and similarities between the HF biocides DBNPA and glutaraldehyde. The microbial community responded to DBNPA differently in HF-impacted versus HF-unimpacted microcosms in terms of the number of 16S rRNA gene copies quantified, alpha and beta diversity, and differential abundance analyses of microbial community composition through time. The differences in microbial community changes affected degradation dynamics. HF-impacted microbial communities were more sensitive to DBNPA, causing the biocide and by-products of the degradation to persist for longer than in HF-unimpacted microcosms. A total of 17 DBNPA by-products were detected, many of them not widely known as DBNPA by-products. Many of the brominated by-products detected that are believed to be uncharacterized may pose environmental and health impacts. Similar taxa were able to tolerate glutaraldehyde and DBNPA; however, DBNPA was not as effective for microbial control, as indicated by a smaller overall decrease of 16S rRNA gene copies/ml after exposure to the biocide, and a more diverse set of taxa was able to tolerate it. These findings suggest that past HF activity in streams can affect the microbial community response to environmental perturbation such as that caused by the biocide DBNPA.

IMPORTANCE Unconventional oil and gas activity can affect pH, total organic carbon, and microbial communities in surface water, altering their ability to respond to new environmental and/or anthropogenic perturbations. These findings demonstrate that 2,2-dibromo-3-nitrilopropionamide (DBNPA), a common hydraulic fracturing (HF) biocide, affects microbial communities differently as a consequence of past HF exposure, persisting longer in HF-impacted (HF+) waters. These findings also demonstrate that DBNPA has low efficacy in environmental microbial communities regardless of HF impact. These findings are of interest, as understanding microbial responses is key for formulating remediation strategies in unconventional oil and gas (UOG)-impacted environments. Moreover, some DBNPA degradation by-products are even more toxic and recalcitrant than DBNPA itself, and this work identifies novel brominated degradation by-products formed.

Oxidative Breakers Can Stimulate Halogenation and Competitive Oxidation in Guar-Gelled Hydraulic Fracturing Fluids

A number of flowback samples derived from horizontally drilled hydraulic fracturing (HDHF) operations reveal consistent detections of halogenated organic species , yet the source of these compounds remains uncertain. Studies simulating subsurface conditions have found that oxidative "breakers" can halogenate certain additives, but these pathways are unverified in the presence of cross-linked-gels, common features of HDHF operations. Using a high-throughput custom reactor system, we implemented a reaction matrix to test the capacity for halogenation of two frequently disclosed compounds with demonstrated halogenation pathways (cinnamaldehyde and citric acid) across guar gels with varied types and concentrations of cross-linkers and oxidative breakers. Cinnamaldehyde halogenation proceeded most readily in borate cross-linked gels at high ammonium persulfate dosages. Citric acid formed trihalomethanes (THMs) broadly across the matrix, generating brominated THMs at higher levels of hypochlorite breaker. Isolated removals of cross-linker or guar enhanced or diminished certain product formations, highlighting additional capacities for relevant ingredients to influence halogenation. Finally, we analyzed flowback samples from the Denver-Julesberg Basin, finding that additions of oxidant enhanced halogenation. As a more realistic subsurface simulation, this work demonstrates strict criteria for the subsurface halogenation of cinnamaldehyde and the broad capacity for THM formation due to systematic oxidant usage as gel breakers in HDHF operations.

The impact of several hydraulic fracking chemicals on Nile tilapia and evaluation of the protective effects of Spirulina platensis

Hydraulic fracturing (fracking) chemicals are used to maximize the extraction of hard-to-reach underground energy resources. Large amounts of fracking fluid could escape to the surrounding environments, including underground and surface water resources, during the chemical mixing stage of the hydraulic fracturing water cycle due to equipment failure or human error. However, the impact of pollution resulting from operational discharges is difficult to assess in aquatic ecosystems. In this study, pathological investigations, chromosomal aberrations, DNA damage, and biochemical and hematological parameters were used to evaluate the effects of such chemicals on Nile tilapia. Chromosomal aberrations are considered very sensitive genetic markers of exposure to genotoxic chemicals and are used as indicators of DNA damage. The appearance of different types of chromosomal aberrations (gaps and breaks) due to chemical exposure was significantly reduced by treatment with spirulina. Various deleterious findings in Nile tilapia, in the current study, could attributed to the presence of fracking chemicals in the aquatic environment. However, the presence of spirulina in the diet reduced the hazards of such chemicals. In addition, cytogenetic studies in the current work revealed the importance of spirulina in ameliorating the genotoxic effects of a mixture of some chemicals used in fracking.

Towards Quantifying the Likelihood of Water Resource Impacts from Unconventional Gas Development

Gas production from unconventional reservoirs has led to widespread environmental concerns. Despite several excellent reviews of various potential impacts to water resources from unconventional gas production, no study has systematically and quantitatively assessed the potential for these impacts to occur. We use empirical evidence and numerical and analytical models to quantify the likelihood of surface water and groundwater contamination, and shallow aquifer depletion from unconventional gas developments. These likelihoods are not intended to be exact. They provide a starting point for comparing the probabilities of adverse impacts between types of water resources and pathways. This analysis provides much needed insight into what are "probable" rather than simply "possible" impacts. The results suggest that the most likely water resource impacts are surface water and groundwater contamination from spills at the well pad, which can be as high as 1 in 10 and 1 in 100 for each gas well, respectively. For wells that are hydraulically fractured, the likelihood of contamination due to inter-aquifer leakage is 1 in 10⁶ or lower (dependent on the separation distance between the production formation and the aquifer). For gas-bearing formations that were initially over-pressurized, the potential for contamination from inter-aquifer leakage after production ceases could be as high as 1 in 400 where the separation between gas formation and shallow aquifer is 500 m, but will be much lower for greater separation distances (more characteristic of shale gas).

Glutaraldehyde inhibits biological treatment of organic additives in hydraulic fracturing produced water

Water generated by hydraulic fracturing for the production of oil and gas, commonly termed 'produced water', may contain residual organic compounds from the fracturing process or the subsurface formation. Biological treatment is a potential technology to remove residual organic compounds in produced water. Biocides are often added to both fracturing fluids and produced water to limit undesirable microbiological activity, and glutaraldehyde is the most commonly used biocide in hydraulic fracturing. Residual biocides in produced water can limit biological treatment efficiency. We evaluated the effect of glutaraldehyde on the biodegradation of five of the most commonly reported organic compounds in hydraulic fracturing fluids in an engineered biofilm treatment. Our results demonstrated that glutaraldehyde delays biological organic compound removal by introducing a biodegradation lag phase. In addition, the effects of glutaraldehyde were more pronounced for more rapidly degraded compounds. Finally, the presence of glutaraldehyde did not decrease microbial abundance nor drive microbial community structure, suggesting that observed effects were due to altered microbial activity. These results highlight the necessity to consider co-contaminant interactions during treatment of complex waste streams where residual biocide may be present.

An Adverse Outcome Pathway Linking Organohalogen Exposure to Mitochondrial Disease

Adverse outcome pathways (AOPs) are pragmatic tools in human health hazard characterization and risk assessment. As such, one of the main goals of AOP development is to provide a clear, progressive, and linear mechanistic representation of pertinent toxicological key events (KEs) occurring along the different levels of biological organization. Here, we present an AOP framework that depicts how exposure to organohalogens can lead to mitochondrial disease. Organohalogens are disinfectant by-products (DBPs) found in our drinking water. Chloroform, trichloroacetic acid, and trichlorophenol were selected to represent specific types of organohalogens for the development of this AOP. Although each of these compounds contains chlorine atoms, they differ in aromaticity and solubility, which have a significant impact on their potency. This AOP consists of two main pathways, both of which are triggered by the molecular initiating event (MIE) of excessive reactive oxygen species generation. Pathway 1 details the downstream consequences of oxidative stress, which include mitochondrial DNA damage, protein aggregation, and depolarization of the mitochondrial membrane. Pathway 2 shows the KEs that result from inadequate supply of glutathione, including calcium dysregulation and ATP depletion. Pathways 1 and 2 converge at a common KE: opening of the mitochondrial membrane transition pore (mPTP). This leads to the release of cytochrome c, caspase activation, apoptosis, and mitochondrial disease. This AOP was developed according to the Organisation for Economic Co-operation and Development guidance, including critical consideration of the Bradford Hill criteria for Weight of Evidence assessment and key questions for evaluating confidence. The presented AOP is expected to serve as the basis for designing new toxicological tests as well as the characterization of novel biomarkers for disinfectant by-product exposure and adverse health effects.

A critical review of risks, characteristics, and treatment strategies for potentially toxic elements in wastewater from shale gas extraction

Shale gas extraction via horizontal drilling and hydraulic fracturing (HF) has enhanced gas production worldwide, which has altered global energy markets and reduced the prices of natural gas and oil. Water management has become the most challenging issue of HF, as it demands vast amounts of freshwater and generates high volumes of complex liquid wastes contaminated by diverse potentially toxic elements at variable rates. This critical review focuses on characterizing HF wastewater and establishing strategies to mitigate environmental impacts. High prioritization was given to the constituents with mean concentrations over 10 times greater than the maximum contamination level (MCL) guidelines for drinking water. A number of potentially harmful organic compounds in HF wastewaters were identified via the risk quotient approach to predict the associated toxicity for freshwater organisms in recipient surface waters. Currently, two options for HF wastewater treatment are preferred, i.e., disposal by deep well injection or on-site re-use as a fracturing fluid. Supplementary treatment will be enforced by increasingly rigorous regulations. Partial treatment and reuse remain the preferred method for managing HF wastewater where feasible. Otherwise, advanced technologies such as membrane separation/distillation, forward osmosis, mechanical vapor compression, electrocoagulation, advanced oxidation, and adsorption-biological treatment will be required to satisfy the sustainable requirements for reuse or surface discharge.

Acute hazard of biocides for the aquatic environmental compartment from a life-cycle perspective

One of the aims of the European project LIFE-COMBASE is to build a computational tool to predict the acute toxicity for aquatic organisms of biocidal active substances and its environmental degradation products. A database was implemented compiling toxicity data for these substances in organisms of the freshwater/marine and sewage treatment plant compartments. The goal of this study is to analyze the compiled data to identify the possible hazard of these compounds for the aquatic compartments. Several official and scientific databases were consulted. Data from 196 biocidal substances and 206 environmental metabolites were collected for the taxonomic groups, including fish, invertebrates, algae and sewage treatment plant (STP) microorganisms. Substances were categorized for their toxicity in four groups, considering values of L(E)C₅₀, according to EU Regulation (EC) No 1272/2008. >50% of the parent were located in category 1 (L(E)C₅₀ ≤ 1 mg/L) for fish, invertebrates and algae, indicating a high toxicity for the freshwater/marine compartments. However >60% were not toxic for STP microorganisms. Metabolites were mainly less toxic than the parent compounds, but 22-36% presented the same toxicity and ~6% were more toxic. No toxicological information was found for ~50% of the metabolites for fish, invertebrates and algae, reaching the 96% for the microorganisms. In addition, information on toxicity to the STP microorganisms was only found for 40% of the parent compounds. The high percentage of toxic metabolites and the scarcity of data for these compounds indicate the need to further study their impact in the aquatic compartments.

Microbial Metabolism and Community Dynamics in Hydraulic Fracturing Fluids Recovered From Deep Hydrocarbon-Rich Shale

Hydraulic fracturing is a prominent method of natural gas production that uses injected, high-pressure fluids to fracture low permeability, hydrocarbon rich strata such as shale. Upon completion of a well, the fluid returns to the surface (produced water) and contains natural gas, subsurface constituents, and microorganisms (Barbot et al., 2013; Daly et al., 2016). While the microbial community of the produced fluids has been studied in multiple gas wells, the activity of these microorganisms and their relation to biogeochemical activity is not well understood. In this experiment, we supplemented produced fluid with ¹³C-labeled carbon sources (glucose, acetate, bicarbonate, methanol, or methane), and ¹⁵N-labeled ammonium chloride in order to isotopically trace microbial activity over multiple day in anoxic incubations. Nanoscale secondary ion mass spectrometry (NanoSIMS) was used to generate isotopic images of ¹³C and ¹⁵N incorporation in individual cells, while isotope ratio monitoring–gas chromatography–mass spectrometry (IRM–GC–MS) was used to measure ¹³CO₂, and ¹³CH₄ as metabolic byproducts. Glucose, acetate, and methanol were all assimilated by microorganisms under anoxic conditions. ¹³CO₂ production was only observed with glucose as a substrate indicating that catabolic activity was limited to this condition. The microbial communities observed at 0, 19, and 32 days of incubation did not vary between different carbon sources, were low in diversity, and composed primarily of the class Clostridia. The primary genera detected in the incubations, Halanaerobium and Fusibacter, are known to be adapted to harsh physical and chemical conditions consistent with those that occur in the hydrofracturing environment. This study provides evidence that microorganisms in produced fluid are revivable in laboratory incubations and retained the ability to metabolize added carbon and nitrogen substrates.

Upregulation of peroxide scavenging enzymes and multidrug efflux proteins highlight an active sodium hypochlorite response in Pseudomonas fluorescens biofilms

The oxidative biocide sodium hypochlorite is among the most commonly used antimicrobial agents in the control of surface-attached microbial communities (biofilms). Clarifying the genetic response of microorganisms in biofilms to hypochlorite may contribute to improved biofilm control strategies. Here, RNA-seq was used to investigate the differential gene expression response of industrially relevant Pseudomonas fluorescens biofilms to sub-lethal concentrations of sodium hypochlorite. Pseudomonas biofilms responded to hypochlorite exposure with increased transcription of genes encoding peroxide scavenging enzymes (e.g., alkyl hydroperoxide reductase (Ahp) and hydroperoxide resistance protein (Ohr)), oxidative stress repair enzymes (e.g., the periplasmic sulfoxide reductase YedYZ complex), and multidrug efflux (e.g., MexEF pumps). In addition, genes involved in amino acid synthesis and energy metabolism were down-regulated following hypochlorite exposure. This work improves the current understanding of genetic response mechanisms to biocides and contributes to the optimization of biocides and application strategies.

Exploring matrix effects and quantifying organic additives in hydraulic fracturing associated fluids using liquid chromatography electrospray ionization mass spectrometry

Hydraulic fracturing (HF) operations utilize millions of gallons of water amended with chemical additives including biocides, corrosion inhibitors, and surfactants. Fluids injected into the subsurface return to the surface as wastewaters, which contain a complex mixture of additives, transformation products, and geogenic chemical constituents. Quantitative analytical methods are needed to evaluate wastewater disposal alternatives or to conduct adequate exposure assessments. However, our narrow understanding of how matrix effects change the ionization efficiency of target analytes limits the quantitative analysis of polar to semi-polar HF additives by means of liquid chromatography electrospray ionization mass spectrometry (LC-ESI-MS). To address this limitation, we explored the ways in which matrix chemistry influences the ionization of seventeen priority HF additives with a modified standard addition approach. We then used the data to quantify HF additives in HF-associated fluids. Our results demonstrate that HF additives generally exhibit suppressed ionization in HF-associated fluids, though HF additives that predominantly form sodiated adducts exhibit significantly enhanced ionization in produced water samples, which is largely the result of adduct shifting. In a preliminary screening, we identified glutaraldehyde and 2-butoxyethanol along with homologues of benzalkonium chloride (ADBAC), polyethylene glycol (PEG), and polypropylene glycol (PPG) in HF-associated fluids. We then used matrix recovery factors to provide the first quantitative measurements of individual homologues of ADBAC, PEG, and PPG in HF-associated fluids ranging from mg L-1 levels in hydraulic fracturing fluid to low μg L-1 levels in PW samples. Our approach is generalizable across sample types and shale formations and yields important data to evaluate wastewater disposal alternatives or implement exposure assessments.

Characterization and biological removal of organic compounds from hydraulic fracturing produced water

Hydraulic fracturing generates large volumes of produced water, and treatment of produced water may be necessary for disposal or reuse. Biological treatment of produced water is a potential approach to remove organic constituents and reduce fouling, in conjunction with other treatment processes. This study investigates the biological treatability of produced water samples from the Utica and Bakken Shales using engineered biofilms. Observed total dissolved organic carbon (DOC) removal varied between 1-87% at normalized total dissolved solids concentrations, suggesting that the composition of produced water, including organic constituents and trace elements such as nutrients and metals, is an important driver of biological treatment performance. Mass spectrometric analyses of the DOC composition revealed various alkanes in all samples, but differences in non-ionic surfactant, halogenated, and acidic compound content. Statistical data reduction approaches suggest that the latter two groups are correlated with reduced biodegradation kinetics. These results demonstrate that the combination of biodegradation performance and organic speciation can guide the assessment of the biological treatment of produced water.

How to Adapt Chemical Risk Assessment for Unconventional Hydrocarbon Extraction Related to the Water System

We identify uncertainties and knowledge gaps of chemical risk assessment related to unconventional drillings and propose adaptations. We discuss how chemical risk assessment in the context of unconventional oil and gas (UO&G) activities differs from conventional chemical risk assessment and the implications for existing legislation. A UO&G suspect list of 1,386 chemicals that might be expected in the UO&G water samples was prepared which can be used for LC-HRMS suspect screening. We actualize information on reported concentrations in UO&G-related water. Most information relates to shale gas operations, followed by coal-bed methane, while only little is available for tight gas and conventional gas. The limited research on conventional oil and gas recovery hampers comparison whether risks related to unconventional activities are in fact higher than those related to conventional activities. No study analyzed the whole cycle from fracturing fluid, flowback and produced water, and surface water and groundwater. Generally target screening has been used, probably missing contaminants of concern. Almost half of the organic compounds analyzed in surface water and groundwater exceed TTC values, so further risk assessment is needed, and risks cannot be waived. No specific exposure scenarios toward groundwater aquifers exist for UO&G-related activities. Human errors in various stages of the life cycle of UO&G production play an important role in the exposure. Neither at the international level nor at the US federal and the EU levels, specific regulations for UO&G-related activities are in place to protect environmental and human health. UO&G activities are mostly regulated through general environmental, spatial planning, and mining legislation.

Succession of toxicity and microbiota in hydraulic fracturing flowback and produced water in the Denver-Julesburg Basin

Hydraulic fracturing flowback and produced water (FPW) samples were analyzed for toxicity and microbiome characterization over 220 days for a horizontally drilled well in the Denver-Julesberg (DJ) Basin in Colorado. Cytotoxicity, mutagenicity, and estrogenicity of FPW were measured via the BioLuminescence Inhibition Assay (BLIA), Ames II mutagenicity assay (AMES), and Yeast Estrogen Screen (YES). Raw FPW stimulated bacteria in BLIA, but were cytotoxic to yeast in YES. Filtered FPW stimulated cell growth in both BLIA and YES. Concentrating 25× by solid phase extraction (SPE) revealed significant toxicity throughout well production by BLIA, toxicity during the first 55 days of flowback by YES, and mutagenicity by AMES. The selective pressures of fracturing conditions (including toxicity) affected bacterial and archaeal communities, which were characterized by 16S rRNA gene V4V5 region sequencing. Conditions selected for thermophilic, anaerobic, halophilic bacteria and methanogenic archaea from the groundwater used for fracturing fluid, and from the native shale community. Trends in toxicity echoed the microbial community, which indicated distinct stages of early flowback water, a transition stage, and produced water. Biota in another sampled DJ Basin horizontal well resembled similarly aged samples from this well. However, microbial signatures were unique compared to samples from DJ Basin vertical wells, and wells from other basins. These data can inform treatability, reuse, and management decisions specific to the DJ Basin to minimize adverse environmental health and well production outcomes.

Applications of thermal desorption coupled to comprehensive two-dimensional gas chromatography/time-of-flight mass spectrometry for hydrocarbon fingerprinting of hydraulically fractured shale rocks

Development of shale gas resources through the use of hydraulic fracturing has raised a multitude of environmental concerns and motivated research towards the understanding of shale gas systems. Previous research has demonstrated the potential of utilizing hydrocarbon distributions towards the fingerprinting of a potential environmental contamination event arising from shale gas operations. However, to apply hydrocarbon distributions from shale gas wells towards point-source identification and apportionment, a better understanding of hydrocarbon origins must be achieved. Here we present an efficient and repeatable thermal desorption method, as a sample introduction methodology for GC × GC analysis of shale rock samples that results in comparable chromatograms to those produced by solvent extraction. This novel and robust characterization technique of shale cores from Marcellus and Utica formations by thermal desorption followed by GC × GC enables the understanding of hydrocarbon speciation within the native rock with minimal sample preparation time and solvent use. The detailed shale chemistry gives insight into utilizing hydrocarbon differences towards point-source identification methodologies of environmental contamination events associated with unconventional gas development. Additionally, this analytical technique may provide a more detailed analysis of hydrocarbons than what is currently implemented in the industry to pinpoint the most advantageous areas to exploit by hydraulic fracturing, yet avoiding undesirable areas such as those with a high abundance of sulfur containing compounds.

Treatment modalities for the reuse of produced waste from oil and gas development

Unconventional oil and gas development is achieved through a series of sub-processes, which utilize large amounts of water, proppant, and chemical additives to retrieve sequestered hydrocarbons from low permeability petroliferous strata. As a result, a large amount of wastewater is produced, which is traditionally disposed of via subsurface injection into non-productive stratum throughout the country. However, this method of waste management has been linked to the induction of seismic events in a number of regions across North America, calling into question the environmental stewardship and sustainability of subsurface waste disposal. Advancements in water treatment technologies have improved the efficacy and financial viability of produced water recycling for beneficial reuse in the oil and gas sector. This review will cover the various treatment options that are currently being utilized in shale energy basins to remove organic, inorganic, and biological constituents, as well as some emerging technologies that are designed to remove pertinent contaminants that would otherwise preclude the reuse of produced water for production well stimulation.

Effect of selected biocides on microbiologically influenced corrosion caused by Desulfovibrio ferrophilus IS5

The marine bacterial strain Desulfovibrio ferrophilus IS5, known for its lithotrophic growth ability to use metallic iron as a sole electron donor and for causing corrosion of steel, was used in the current study. Four commonly used biocides in the oil and gas industry, namely tetrakis(hydroxymethyl) phosphonium sulfate (THPS), glutaraldehyde (GLUT), benzalkonium chloride (BAC), and GLUT/BAC were selected to study their efficacy in controlling carbon steel corrosion in the presence of this strain. Incubations containing strain IS5 and low carbon steel coupons were prepared in the presence and absence of the four biocides, and these were monitored using both electrochemical methods (electrochemical impedance spectroscopy, linear polarization resistance and potentiodynamic polarization) and surface analyses (scanning electron microscopy, confocal measurements, optical microscopy, and profilometry) to assess the biofilm/metal interactions. When THPS, BAC, and GLUT/BAC treatments were applied, minimal corrosion was measured by all methods. In contrast, severe pitting was observed in the presence of 50 ppm GLUT, similar to what was observed when D. ferrophilus IS5 was incubated in the absence of biocide, suggesting that GLUT alone may not be effective in controlling MIC in marine environments. This study also showed that the use of non-destructive electrochemical methods is effective for screening for real time biocide selection and monitoring of the impact of chemicals post-dosage in oil and gas operations.

Groundwater Quality and Hydraulic Fracturing: Current Understanding and Science Needs

Hydraulic fracturing (fracking) is a process used for the stimulation and production of ultra-low permeability shale gas and tight oil resources. Fracking poses two main risks to groundwater quality: (1) stray gas migration and (2) potential contamination from chemical and fluid spills. Risk assessment is complicated by the lack of predrilling baseline measurements, limited access to well sites and industry data, the constant introduction of new chemical additives to frack fluids, and difficulties comparing data sets obtained by different sampling and analytical methods. Specific recommendations to reduce uncertainties and meet science needs for better assessment of groundwater risks include improving data-sharing among researchers, adopting standardized methodologies, collecting predrilling baseline data, installing dedicated monitoring wells, developing shale-specific environmental indicators, and providing greater access to field sites, samples, and industry data to the research community.

A community-based evaluation of proximity to unconventional oil and gas wells, drinking water contaminants, and health symptoms in Ohio

Over 4 million Americans live within 1.6 km of an unconventional oil and gas (UO&G) well, potentially placing them in the path of toxic releases. We evaluated relationships between residential proximity to UO&G wells and (1) water contamination and (2) health symptoms in an exploratory study. We analyzed drinking water samples from 66 Ohio households for 13 UO&G-related volatile organic compounds (VOCs) (e.g., benzene, disinfection byproducts [DBPs]), gasoline-range organics (GRO), and diesel-range organics. We interviewed participants about health symptoms and calculated metrics capturing proximity to UO&G wells. Based on multivariable logistic regression, odds of detection of bromoform and dibromochloromethane in surface water decreased significantly as distance to nearest UO&G well increased (odds ratios [OR]: 0.28-0.29 per km). Similarly, distance to nearest well was significantly negatively correlated with concentrations of GRO and toluene in ground water (r_Spearman: -0.40 to -0.44) and with concentrations of bromoform and dibromochloromethane in surface water (r_Spearman: -0.48 to -0.50). In our study population, those with higher inverse-distance-squared-weighted UO&G well counts within 5 km around the home were more likely to report experiencing general health symptoms (e.g. stress, fatigue) (OR: 1.52, 95%CI: 1.02-2.26). This exploratory study, though limited by small sample size and self-reported health symptoms, suggests that those in closer proximity to multiple UO&G wells may be more likely to experience environmental health impacts. Further, presence of brominated DBPs (linked to UO&G wastewater) raises the question of whether UO&G activities are impacting drinking water sources in the region. The findings from this study support expanded studies to advance knowledge of the potential for water quality and human health impacts; such studies could include a greater number of sampling sites, more detailed chemical analyses to examine source attribution, and objective health assessments.

Estimating Radium Activity in Shale Gas Produced Brine

Shale gas reservoir-produced brines may contain elevated levels of naturally occurring radioactive material, including Ra-226 and Ra-228, which come from the decay of U-238 and Th-232 in shale. While the total Ra activity in shale gas wastewaters can vary by over 3 orders of magnitude, the parent radionuclides tend to only vary by 1 order of magnitude. The extent of Ra mobilization from the shale into produced brines is thought to be largely controlled by adsorption/desorption from the shale, which is influenced by shale cation exchange capacity (CEC) and reservoir brine salinity, often reported as the total dissolved solids (TDS). To determine how these factors lead to such large variation in Ra activity of produced brines, the U content and CEC of shale samples from the Antrim and Utica-Collingwood shales in Michigan and the Marcellus shale in Pennsylvania were evaluated. Analysis of produced brine from 17 Antrim shale gas wells was then used to develop an empirical relationship between Ra-226 activity and produced water TDS for a given U content of the shale. This correlation will provide an a priori estimate of the expected Ra activity of a produced brine from a given shale gas play when the brine salinity and U content of the shale are known. Such information can serve as a guide for optimal wastewater treatment and disposal strategies prior to any drilling activity, thereby reducing risks associated with elevated Ra activity in shale gas wastewaters.

Halogenation Chemistry of Hydraulic Fracturing Additives under Highly Saline Simulated Subsurface Conditions

Unconventional natural gas extraction via hydraulic fracturing coupled with horizontal drilling (HDHF) has generated disruptive growth in the domestic energy sector. Field analyses of residual HDHF fluids have detected halogenated species, potentially the product of unexplored reactions between authigenic halides and HDHF additives. Utilizing a custom high-pressure reactor system, we simultaneously screened 12 frequently disclosed, functionally diverse HDHF additives to uncover transformation chemistry. One emergent pathway, the halogenation of cinnamaldehyde in the presence of ammonium persulfate, demonstrated the potential for oxidative breakers to react with halides to yield reactive halogen species. Halogenated product formation, product distribution, and kinetics were evaluated with respect to shale well subsurface condition, linking transformation risk to measurable well-dependent characteristics (e.g., halide compositions, well temperatures, and pH). In a representative flowback brine, the brominated product dominated on a molar percent basis (6 ± 2%, as normalized by initial cinnamaldehyde loading) over chlorinated (1.4 ± 0.4%) and iodinated forms (2.5 ± 0.9%), reflecting relative halide abundance and propensity for oxidation. This work demonstrates that relevant subsurface reactions between natural brines and hydraulic fracturing additives can result in the unintended formation of halogenated products.

The intensification of the water footprint of hydraulic fracturing

Unconventional oil and gas exploration in the United States has experienced a period of rapid growth, followed by several years of limited production due to falling and low natural gas and oil prices. Throughout this transition, the water use for hydraulic fracturing and wastewater production in major shale gas and oil production regions has increased; from 2011 to 2016, the water use per well increased up to 770%, while flowback and produced water volumes generated within the first year of production increased up to 1440%. The water-use intensity (that is, normalized to the energy production) increased ubiquitously in all U.S. shale basins during this transition period. The steady increase of the water footprint of hydraulic fracturing with time implies that future unconventional oil and gas operations will require larger volumes of water for hydraulic fracturing, which will result in larger produced oil and gas wastewater volumes.

The water footprint of hydraulic fracturing in Sichuan Basin, China

Shale gas is likely to play a major role in China's transition away from coal. In addition to technological and infrastructural constraints, the main challenges to China's sustainable shale gas development are sufficient shale gas production, water availability, and adequate wastewater management. Here we present, for the first time, actual data of shale gas production and its water footprint from the Weiyuan gas field, one of the major gas fields in Sichuan Basin. We show that shale gas production rates during the first 12 months (24 million m³ per well) are similar to gas production rates in U.S. shale basins. The amount of water used for hydraulic fracturing (34,000 m³ per well) and the volume of flowback and produced (FP) water in the first 12 months (19,800 m³ per well) in Sichuan Basin are also similar to the current water footprints of hydraulic fracturing in U.S. basins. We present salinity data of the FP water (5000 to 40,000 mgCl/L) in Sichuan Basin and the treatment operations, which include sedimentation, dilution with fresh water, and recycling of the FP water for hydraulic fracturing. We utilize the water use data, empirical decline rates of shale gas and FP water productions in Sichuan Basin to generate two prediction models for water use for hydraulic fracturing and FP water production upon achieving China's goals to generate 100 billion m³ of shale gas by 2030. The first model utilizes the current water use and FP production data, and the second assumes a yearly 5% intensification of the hydraulic fracturing process. The predicted water use for hydraulic fracturing in 2030 (50-65 million m³ per year), FP water production (50-55 million m³ per year), and fresh water dilution of FP water (25 million m³ per year) constitute a water footprint that is much smaller than current water consumption and wastewater generation for coal mining, but higher than those of conventional gas production in China. Given estimates for water availability in Sichuan Basin, our predictions suggest that water might not be a limiting factor for future large-scale shale gas development in Sichuan Basin.

Effect of long term application of tetrakis(hydroxymethyl)phosphonium sulfate (THPS) in a light oil-producing oilfield

Samples of (I) produced waters, (II) central processing facility (CPF) waters and (III) pipeline solids were collected from a light oil-producing field. The biocide, tetrakis(hydroxymethyl)phosphonium sulfate (THPS) was routinely used in the CPF. Samples monitoring indicated that THPS was effective in microbial control but also increased concentrations of sulfate and phosphate in transitioning from Type I to Type II waters. Type II waters had high concentrations (up to 60 mM) of acetate but low most probable numbers (MPNs) of acid-producing and sulfate-reducing bacteria, indicating the presence of active biocide, as high MPNs were found in Type I waters. Solids had high phosphate and high MPNs, indicating that THPS was inactive. Solids had oil and an anaerobic community dominated by Acetobacterium, which may contribute to conversion of oil to acetate. The presence of THPS prevented the use of this acetate in Type II waters, where it accumulated to unusually high concentrations.

Cellular adverse actions of dibromoacetonitrile, a by-product in water bacterial control, at sublethal levels in rat thymocytes

The aim of this study was to investigate the effects of dibromoacetonitrile (DBAN), a by-product in water bacterial control, at sublethal concentrations on rat thymocytes, by using a cytometric technique with appropriate fluorescent dyes. By using this method, the possibility that DBAN induces cellular actions related to oxidative stress was assessed. DBAN reduced the content of cellular nonprotein thiols under Zn²⁺-free conditions. It elevated the intracellular level of Zn²⁺, being independent from external Zn²⁺. DBAN increased cell vulnerability to the cytotoxic action of hydrogen peroxide. These actions of DBAN were likely related to oxidative stress. DBAN is formed by the reaction of bromides and chlorinated oxidants during water disinfection. Hydrolysis of 2,2-dibromo-3-nitrilopropionamide, an antimicrobial used in hydraulic fracturing fluids for production of shale gas and oil, produces DBAN. Therefore, the concern regarding the levels of DBAN in industrial water systems is necessary to avoid the environmental risk to humans and wild mammals.

Impacts of Glutaraldehyde on Microbial Community Structure and Degradation Potential in Streams Impacted by Hydraulic Fracturing

The environmental impacts of hydraulic fracturing, particularly those of surface spills in aquatic ecosystems, are not fully understood. The goals of this study were to (1) understand the effect of previous exposure to hydraulic fracturing fluids on aquatic microbial community structure and (2) examine the impacts exposure has on biodegradation potential of the biocide glutaraldehyde. Microcosms were constructed from hydraulic fracturing-impacted and nonhydraulic fracturing-impacted streamwater within the Marcellus shale region in Pennsylvania. Microcosms were amended with glutaraldehyde and incubated aerobically for 56 days. Microbial community adaptation to glutaraldehyde was monitored using 16S rRNA gene amplicon sequencing and quantification by qPCR. Abiotic and biotic glutaraldehyde degradation was measured using ultra-performance liquid chromatography--high resolution mass spectrometry and total organic carbon. It was found that nonhydraulic fracturing-impacted microcosms biodegraded glutaraldehyde faster than the hydraulic fracturing-impacted microcosms, showing a decrease in degradation potential after exposure to hydraulic fracturing activity. Hydraulic fracturing-impacted microcosms showed higher richness after glutaraldehyde exposure compared to unimpacted streams, indicating an increased tolerance to glutaraldehyde in hydraulic fracturing impacted streams. Beta diversity and differential abundance analysis of sequence count data showed different bacterial enrichment for hydraulic fracturing-impacted and nonhydraulic fracturing-impacted microcosms after glutaraldehyde addition. These findings demonstrated a lasting effect on microbial community structure and glutaraldehyde degradation potential in streams impacted by hydraulic fracturing operations.

Use of carbon steel ball bearings to determine the effect of biocides and corrosion inhibitors on microbiologically influenced corrosion under flow conditions

A consortium of sulfate-reducing bacteria consisting mostly of Desulfovibrio, Desulfomicrobium, and Desulfocurvus from oil field produced water was cultivated in a chemostat, receiving medium with 20 mM formate and 10 mM sulfate as the energy and 1 mM acetate as the carbon source. The chemostat effluent, containing 5 mM sulfide and 0.5 mM of residual acetate, was passed through 1-ml syringe columns with 60 carbon steel ball bearings (BBs) of 53.6 ± 0.1 mg each at a flow rate of 0.8 ml/h per column. These were treated every 5 days with 1.6 ml of 300 ppm of glutaraldehyde (Glut), tetrakis(hydroxymethyl)phosphonium sulfate (THPS), benzalkonium chloride (BAC), or Glut/BAC, a mixture of Glut and BAC. Alternatively, BBs were treated with 33% (v/v) of a water-soluble (CR_W) or an oil-soluble (CR_O1 or CR_O3) corrosion inhibitor for 20 s after which the corrosion inhibitor was drained off and BBs were packed into columns. The effluent of untreated control columns had no acetate. Treatment with the chemically reactive biocides Glut and THPS, as well as with Glut/BAC, gave a transient increase of acetate indicating decreased microbial activity. This was not seen with BAC alone indicating it to be the least effective biocide. Relative to untreated BBs (100%), those treated periodically with Glut, THPS, BAC, or Glut/BAC had a general weight loss corrosion rate of 91, 81, 45, and 36% of the untreated rate of 0.104 ± 0.004 mm/year, respectively. Single treatment with corrosion inhibitors decreased corrosion to 48, 2, and 1% of the untreated rate for CR_W, CR_O1 and CR_O3, respectively. Analysis of the distribution of corrosion rates from the weight loss of individual BBs (N = 120) indicated the presence of a more slowly and a more rapidly corroding group. BAC treatment prevented emergence of the latter, and this quaternary ammonium detergent appeared most effective in decreasing corrosion not because of its biocidal properties, but because of its corrosion inhibitory properties.

In vitro nuclear receptor inhibition and cytotoxicity of hydraulic fracturing chemicals and their binary mixtures

The widespread use of hydraulic fracturing (HF) in oil and gas extraction operations has led to concern over environmental risks posed by chemicals used in HF fluids. Here we employed a suite of stable luciferase reporter gene assays to investigate the potential for selected HF chemicals or geogenics to activate or antagonise nuclear receptor signalling. We screened three biocides (bronopol [BP], glutaraldehyde [GA], and tetrakis(hydroxymethyl)phosphonium sulfate [THPS]), a surfactant (2-butoxyethanol), a friction reducer (polyacrylamide), and a coal seam geogenic (o-cresol) for their potential to act as agonists or antagonists of the estrogen receptor, androgen receptor, progesterone receptor (PR), glucocorticoid receptor or peroxisome proliferator-activated receptor gamma (PPARγ). None of the chemicals induced luciferase activity in any of assays used in the study. In antagonistic mode, BP, GA and THPS caused reductions in luciferase activity in the reporter assays at higher concentrations (50-100 μM), while at low concentrations (2-10 μM) GA and THPS enhanced luciferase activity in some assays relative to controls. None of the other tested chemicals exhibited antagonism in the selected assays. In most cases, altered receptor signalling only occurred at concentrations exhibiting cytotoxicity. However, PPARγ activity, and to a lesser extent PR activity, were inhibited by THPS at sub-cytotoxic concentrations. The majority of binary combinations tested exhibited significantly less-than-additive cytotoxicity, and none of the combinations exhibited synergistic cytotoxicity. In summary, the results of the present study indicate that the selected chemicals are not likely to function as direct agonists of the nuclear receptors tested, and only one chemical, THPS was an apparent partial antagonist of two nuclear receptors.

Elucidating Environmental Fingerprinting Mechanisms of Unconventional Gas Development through Hydrocarbon Analysis

Hydraulic fracturing is an increasingly common technique for the extraction of natural gas entrapped in shale formations. This technique has been highly criticized due to the possibility of environmental contamination, underscoring the need for method development to identify chemical factors that could be utilized in point-source identification of environmental contamination events. Here, we utilize comprehensive two-dimensional gas chromatography (GC × GC) coupled to high-resolution time-of-flight (HRT) mass spectrometry, which offers a unique instrumental combination allowing for petroleomics hydrocarbon fingerprinting. Four flowback fluids from Marcellus shale gas wells in geographic proximity were analyzed for differentiating factors that could be exploited in environmental forensics investigations of shale gas impacts. Kendrick mass defect (KMD) plots of these flowback fluids illustrated well-to-well differences in heteroatomic substituted hydrocarbons, while GC × GC separations showed variance in cyclic hydrocarbons and polyaromatic hydrocarbons among the four wells. Additionally, generating plots that combine GC × GC separation with KMD established a novel data-rich visualization technique that further differentiated the samples.

Common Hydraulic Fracturing Fluid Additives Alter the Structure and Function of Anaerobic Microbial Communities

The development of unconventional oil and gas (UOG) resources results in the production of large volumes of wastewater containing a complex mixture of hydraulic fracturing chemical additives and components from the formation. The release of these wastewaters into the environment poses potential risks that are poorly understood. Microbial communities in stream sediments form the base of the food chain and may serve as sentinels for changes in stream health. Iron-reducing organisms have been shown to play a role in the biodegradation of a wide range of organic compounds, and so to evaluate their response to UOG wastewater, we enriched anaerobic microbial communities from sediments collected upstream (background) and downstream (impacted) of an UOG wastewater injection disposal facility in the presence of hydraulic fracturing fluid (HFF) additives: guar gum, ethylene glycol, and two biocides, 2,2-dibromo-3-nitrilopropionamide (DBNPA) and bronopol (C₃H₆BrNO₄). Iron reduction was significantly inhibited early in the incubations with the addition of biocides, whereas amendment with guar gum and ethylene glycol stimulated iron reduction relative to levels in the unamended controls. Changes in the microbial community structure were observed across all treatments, indicating the potential for even small amounts of UOG wastewater components to influence natural microbial processes. The microbial community structure differed between enrichments with background and impacted sediments, suggesting that impacted sediments may have been preconditioned by exposure to wastewater. These experiments demonstrated the potential for biocides to significantly decrease iron reduction rates immediately following a spill and demonstrated how microbial communities previously exposed to UOG wastewater may be more resilient to additional spills.IMPORTANCE Organic components of UOG wastewater can alter microbial communities and biogeochemical processes, which could alter the rates of essential natural attenuation processes. These findings provide new insights into microbial responses following a release of UOG wastewaters and are critical for identifying strategies for the remediation and natural attenuation of impacted environments.

Temporal characterization and statistical analysis of flowback and produced waters and their potential for reuse

Hydraulic fracturing (HF) has allowed for the utilization of previously unattainable shale oil and gas (O&G) resources. After HF is complete, the waters used to increase the facies' permeability return uphole as wastewaters. When these waters return to the surface, they are characterized by complex organic and inorganic chemistry, and can pose a health risk if not handled correctly. Therefore, these waters must be treated or disposed of properly. However, the variability of these waters' chemical composition over time is poorly understood and likely limits the applicability of their reuse. This study examines the water chemistry of a hydraulically fractured site in the Niobrara formation throughout the flowback period. Samples were collected every other day for the first 18days, then on a regular basis for three months. We identified HF fluid additives, including benzalkonium chlorides (BACs), alkyl ethoxylates (AEOs), and polyethylene glycols (PEGs), as well as geogenic components present in flowback and produced waters, their overall temporal pattern, and variables affecting the reuse of these waters. Observations indicate that alkalinity and iron may limit the reuse of these waters in HF, while chloride and alkalinity may limit the use of these waters for well-casing cement. The presence of numerous surfactant homologs, including biocides, was also observed, with the highest levels at the beginning of the flowback period. Principal component analysis identified three unique groupings in the chemical data that correspond to different stages in the flowback period: (1) the flowback stage (days 1-2); (2) the transition stage (days 6-21); and (3) the produced water stage (days 21-87). Results from this study will be important when designing decision frameworks for assessing water treatment options, particularly if onsite treatment is attempted. Successful reclamation of these waters may alleviate stress on water resources that continues to negatively impact the U. S.

Hazard assessment of hydraulic fracturing chemicals using an indexing method

The rapid expansion of unconventional natural gas production has triggered considerable public concerns, particularly regarding environmental and human health (EHH) risks posed by various chemical additives used in hydraulic fracturing (HF) operations. There is a need to assess the potential EHH hazards of additives used in real-world HF operations. In this study, HF additive and fracturing fluid data was acquired, and EHH hazards were assessed using an indexing approach. The indexing system analyzed chemical toxicological data of different ingredients contained within additives and produced an aggregated EHH safety index for each additive, along with an indicator describing the completeness of the chemical toxicological data. The results show that commonly used additives are generally associated with medium-level EHH hazards. In each additive category, ingredients of high EHH concern were identified, and the high hazard designation was primarily attributed to ingredients' high aquatic toxicity and carcinogenic effects. Among all assessed additive categories, iron control agents were identified as the greatest EHH hazards. Lack of information, such as undisclosed ingredients and chemical toxicological data gaps, has resulted in different levels of assessment uncertainties. In particular, friction reducers show the highest data incompleteness with regards to EHH hazards. This study reveals the potential EHH hazards associated with chemicals used in current HF field operations and can provide decision makers with valuable information to facilitate sustainable and responsible unconventional gas production.

Developmental Toxicity of the Organic Fraction from Hydraulic Fracturing Flowback and Produced Waters to Early Life Stages of Zebrafish ( Danio rerio)

Hydraulic fracturing (HF) has emerged as a major recovery method of unconventional oil and gas reservoirs and concerns have been raised regarding the environmental impact of releases of Flowback and Produced Water (FPW) to aquatic ecosystems. To investigate potential effects of HF-FPW on fish embryo development, HF-FPW samples were collected from two different wells and the organic fractions were isolated from both aqueous and particle phases to eliminate the confounding effects of high salinity. Each organic extract was characterized by non-target analysis with HPLC-Orbitrap-MS, with targeted analysis for polycyclic aromatic hydrocarbons provided as markers of petroleum-affected water. The organic profiles differed between samples, including PAHs and alkyl PAHs, and major substances identified by non-target analysis included polyethylene glycols, alkyl ethoxylates, octylphenol ethoxylates, and other high molecular weight (C_49-79) ethylene oxide polymeric material. Zebrafish embryos were exposed to various concentrations of FPW organic extracts to investigate acute (7-day) and developmental toxicity in early life stages. The acute toxicity (LD₅₀) of the extracted FPW fractions ranged from 2.8× to 26× the original organic content. Each extracted FPW fraction significantly increased spinal malformation, pericardial edema, and delayed hatch in exposed embryos and altered the expression of a suite of target genes related to biotransformation, oxidative stress, and endocrine-mediation in developing zebrafish embryos. These results provide novel information on the variation of organic profiles and developmental toxicity among different sources and fractions of HF-FPWs.

Molecular insights into competitive adsorption of CO2/CH4 mixture in shale nanopores

In the present study, competitive adsorption behaviour of supercritical carbon dioxide and methane binary mixture in shale organic nanopores was investigated by using grand canonical Monte Carlo (GCMC) simulations. The model was firstly validated by comparing with experimental data and a satisfactory agreement was obtained. Then the effects of temperature (298–388 K), pressure (up to 60 MPa), pore size (1–4 nm) and moisture content (0–2.4 wt%) on competitive adsorption behaviour of the binary mixture were examined and discussed in depth. It is found that the adsorption capacity of carbon dioxide in shale organic nanopores is much higher than that of methane under various conditions. The mechanism of competitive adsorption was discussed in detail. In addition, the results show that a lower temperature is favorable to both the adsorption amount and selectivity of CO₂/CH₄ binary mixture in shale organic nanopores. However, an appropriate CO₂ injection pressure should be considered to take into account the CO₂ sequestration amount and the exploitation efficiency of shale gas. As for moisture content, different influences on CO₂/CH₄ adsorption selectivity have been observed at low and high moisture conditions. Therefore, different simulation technologies for shale gas production and CO₂ sequestration should be applied depending on the actual moisture conditions of the shale reservoirs. It is expected that the findings in this work could be helpful to estimate and enhance shale gas resource recovery and also evaluate CO₂ sequestration efficiency in shale reservoirs.

Competitive adsorption behaviour of CO₂/CH₄ mixture in shale slit nanopores under various geological conditions was explored by molecular simulations.

Organic compounds in hydraulic fracturing fluids and wastewaters: A review

High volume hydraulic fracturing (HVHF) of shale to stimulate the release of natural gas produces a large quantity of wastewater in the form of flowback fluids and produced water. These wastewaters are highly variable in their composition and contain a mixture of fracturing fluid additives, geogenic inorganic and organic substances, and transformation products. The qualitative and quantitative analyses of organic compounds identified in HVHF fluids, flowback fluids, and produced waters are reviewed here to communicate knowledge gaps that exist in the composition of HVHF wastewaters. In general, analyses of organic compounds have focused on those amenable to gas chromatography, focusing on volatile and semi-volatile oil and gas compounds. Studies of more polar and non-volatile organic compounds have been limited by a lack of knowledge of what compounds may be present as well as quantitative methods and standards available for analyzing these complex mixtures. Liquid chromatography paired with high-resolution mass spectrometry has been used to investigate a number of additives and will be a key tool to further research on transformation products that are increasingly solubilized through physical, chemical, and biological processes in situ and during environmental contamination events. Diverse treatments have been tested and applied to HVHF wastewaters but limited information has been published on the quantitative removal of individual organic compounds. This review focuses on recently published information on organic compounds identified in flowback fluids and produced waters from HVHF.

Inhibition of Biodegradation of Hydraulic Fracturing Compounds by Glutaraldehyde: Groundwater Column and Microcosm Experiments

The rapid expansion of unconventional oil and gas development has raised concerns about the potential contamination of aquifers; however, the groundwater fate and transport of hydraulic fracturing fluid compounds and mixtures remains a significant data gap. Degradation kinetics of five hydraulic fracturing compounds (2-propanol, ethylene glycol, propargyl alcohol, 2-butoxyethanol, and 2-ethylhexanol) in the absence and presence of the biocide glutaraldehyde were investigated under a range of redox conditions using sediment-groundwater microcosms and flow-through columns. Microcosms were used to elucidate biodegradation inhibition at varying glutaraldehyde concentrations. In the absence of glutaraldehyde, half-lives ranged from 13 d to >93 d. Accurate mass spectrometry indicated that a trimer was the dominant aqueous-phase glutaraldehyde species. Microbial inhibition was observed at glutaraldehyde trimer concentrations as low as 5 mg L^-1, which demonstrated that the trimer retained some biocidal activity. For most of the compounds, biodegradation rates slowed with increasing glutaraldehyde concentrations. For many of the compounds, degradation was faster in the columns than the microcosms. Four compounds (2-propanol, ethylene glycol, propargyl alcohol, and 2-butoxyethanol) were found to be both mobile and persistent in groundwater under a range of redox conditions. The glutaraldehyde trimer and 2-ethylhexanol were more rapidly degraded, particularly under oxic conditions.