Construction of an Acetate Metabolic Pathway to Enhance Electron Generation of Engineered Shewanella oneidensis

Background: Microbial fuel cells (MFCs) are a novel bioelectrochemical devices that can use exoelectrogens as biocatalyst to convert various organic wastes into electricity. Among them, acetate, a major component of industrial biological wastewater and by-product of lignocellulose degradation, could release eight electrons per mole when completely degraded into CO₂ and H₂O, which has been identified as a promising carbon source and electron donor. However, Shewanella oneidensis MR-1, a famous facultative anaerobic exoelectrogens, only preferentially uses lactate as carbon source and electron donor and could hardly metabolize acetate in MFCs, which greatly limited Coulombic efficiency of MFCs and the capacity of bio-catalysis. Results: Here, to enable acetate as the sole carbon source and electron donor for electricity production in S. oneidensis, we successfully constructed three engineered S. oneidensis (named AceU1, AceU2, and AceU3) by assembling the succinyl-CoA:acetate CoA-transferase (SCACT) metabolism pathways, including acetate coenzyme A transferase encoded by ato1 and ato2 gene from G. sulfurreducens and citrate synthase encoded by the gltA gene from S. oneidensis, which could successfully utilize acetate as carbon source under anaerobic and aerobic conditions. Then, biochemical characterizations showed the engineered strain AceU3 generated a maximum power density of 8.3 ± 1.2 mW/m² with acetate as the sole electron donor in MFCs. In addition, when further using lactate as the electron donor, the maximum power density obtained by AceU3 was 51.1 ± 3.1 mW/m², which approximately 2.4-fold higher than that of wild type (WT). Besides, the Coulombic efficiency of AceU3 strain could reach 12.4% increased by 2.0-fold compared that of WT, which demonstrated that the engineered strain AceU3 can further utilize acetate as an electron donor to continuously generate electricity. Conclusion: In the present study, we first rationally designed S. oneidensis for enhancing the electron generation by using acetate as sole carbon source and electron donor. Based on synthetic biology strategies, modular assembly of acetate metabolic pathways could be further extended to other exoelectrogens to improve the Coulombic efficiency and broaden the spectrum of available carbon sources in MFCs for bioelectricity production.

Perspective on advanced nanomaterials used for energy storage and conversion

To drive the next ‘technical revolution’ towards commercialization, we must develop sustainable energy materials, procedures, and technologies. The demand for electrical energy is unlikely to diminish over the next 50 years, and how different countries engage in these challenges will shape future discourse. This perspective summarizes the technical aspects of nanomaterials’ design, evaluation, and uses. The applications include solid oxide fuel cells (SOFCs), solid oxide electrolysis cells (SOEC), microbial fuel cells (MFC), supercapacitors, and hydrogen evolution catalysts. This paper also described energy carriers such as ammonia which can be produced electrochemically using SOEC under ambient pressure and high temperature. The rise of electric vehicles has necessitated some form of onboard storage of fuel or charge. The fuels can be generated using an electrolyzer to convert water to hydrogen or nitrogen and steam to ammonia. The charge can be stored using a symmetrical supercapacitor composed of tertiary metal oxides with self-regulating properties to provide high energy and power density. A novel metal boride system was constructed to absorb microwave radiation under harsh conditions to enhance communication systems. These resources can lower the demand for petroleum carbon in portable power devices or replace higher fossil carbon in stationary power units. To improve the energy conversion and storage efficiency, we systematically optimized synthesis variables of nanomaterials using artificial neural network approaches. The structural characterization and electrochemical performance of the energy materials and devices provide guidelines to control new structures and related properties. Systemic study on energy materials and technology provides a feasible transition from traditional to sustainable energy platforms. This perspective mainly covers the area of green chemistry, evaluation, and applications of nanomaterials generated in our laboratory with brief literature comparison where appropriate. The conceptual and experimental innovations outlined in this perspective are neither complete nor authoritative but a snapshot of selecting technologies that can generate green power using nanomaterials.

Effect of hydraulic retention time on the denitrification performance and metabolic mechanism of a multi-chambered bio-electrochemical system

The effects of hydraulic retention time (HRT) on the denitrification performance of the multi-chambered bio-electrochemistry system and the metabolic mechanism of the microbial community were investigated. Results indicated that the NO₃^--N and NO₂^--N removal efficiency was up to 99.5% and 99.9%, respectively. The electricity generation performance of the system was optimum at 24 h HRT, with the maximum power density and output voltage of the fourth chamber to be 471.2 mW/m³ and 602.4 mV, respectively. With the decrease of HRT from 24 h to 8 h, the protein-like substance in extracellular polymeric substance (EPS) of granular sludge was reduced and the fluorescence intensities were weakened. Besides, the abundance of metabolism pathway was the highest at 50.0% and 49.9%, respectively, and the methane metabolism (1.8% and 2.0%, respectively) and the nitrogen metabolism (0.8% and 0.9%, respectively) in Kyoto Encyclopedia of Genes and Genomes (KEGG) pathway played important roles in providing guaranteed stability and efficient removal of organic matter and nitrogen from the system.

Bioelectrochemical technology for recovery of silver from contaminated aqueous solution: a review

A large amount of silver-rich wastewater is generated from different industrial processes. This wastewater is not considered a waste, but a valuable source for recovery due to the precious silver (Ag). Previous studies have used traditional methods such as membrane filtration, electrolysis, chemical precipitation, electrochemical, and cementation for Ag recovery. However, many drawbacks have been reported for these techniques such as high cost, hazardous waste generation, and the needed refinement of recovered products. In this study, a bioelectrochemical system (BES) for Ag recovery from aqueous solution is introduced as an effective and innovative method, as compared with other techniques. Different types of Ag(I)-containing solutions that have been investigated in recent BES studies (e.g., Ag⁺ solution, [Ag(NH₃)₂]⁺, [Ag(S₂O₃)]^-, [Ag(S₂O₃)₂]^3- complexes) are reported. A BES is an anaerobic system consisting of anode and cathode chambers, which are normally separated by an ion-exchange membrane. The electron flow obtained from the anodic biological oxidation of organic matter is used directly for the cathodic electrochemical reduction of Ag(I) ions. The recovered product is Ag electrodeposits, formed at the cathode surface. Several studies have reported high Ag recovery efficiency by using a BES (i.e., > 90%), with high purity of metallic silver, and simultaneous electricity production. Furthermore, a BES can be employed for a wide range of initial Ag(I) concentrations (e.g., 50-3000 mg/L). The advantages of BES technology for Ag recovery are highlighted in this study for further practical applications.

Industrial wastewater treatment: Current trends, bottlenecks, and best practices

Rapid urbanization and industrialization have inextricably linked to water consumption and wastewater generation. Mining resources from industrial wastewater has proved to be an excellent source of secondary raw materials i.e., proficient for providing economic and financial benefits, clean and sustainable resilient environment, and achieving sustainable development goals (SDGs). Treatment of industrial wastewater for reusable resources has become a tedious task for decision-makers due to several bottlenecks and barriers, such as inefficient treatment options, high-cost expenditure, poor infrastructure, lack of financial support, and technical know-how. Most of the existing methods are conventional and fails to provide an economic benefit to the industries and have certain disadvantages. Also, the untreated industrial wastewater is discharged into the open drains, lakes, and rivers that lead to environmental pollution and severe health hazards. This paper has consolidated information about the current trends, opportunities, bottlenecks, and best practices associated with wastewater treatment and scope for the advancement in the existing technologies. Along with the efficient resource recovery, the wastewater could be ideally explored in the development of value-added materials, energy, and product recovery. The concepts, such as the circular economy (CE), partitions-release-recover (PRR), and transforming wastewater into bio factory are anticipated to be more convenient options to tackle the industrial wastewater menace.

How bacteria use electric fields to reach surfaces

Electrotaxis is the property of cells to sense electric fields and use them to orient their displacement. This property has been widely investigated with eukaryotic cells but it remains unclear whether or not bacterial cells can sense an electric field. Here, a specific experimental set-up was designed to form microbial electroactive biofilms while differentiating the effect of the electric field from that of the polarised electrode surface. Application of an electric field during exposure of the electrodes to the inoculum was shown to be required for an electroactive biofilm to form afterwards. Similar biofilms were formed in both directions of the electric field. This result is attributed to the capacity of the cells to detect the K+ and Na+ ion gradients that the electric field creates at the electrode surface. This microbial property should now be considered as a key factor in the formation of electroactive biofilms and possible implications in the biomedical domain are discussed.

Sewage denitrification performance and sludge properties variation with the addition of liquid from perishable organic anaerobic fermentation

The organics in the classified wet waste were deficiently utilized while sewage denitrification requires abundant carbon sources. Herein, the fermentation of perishable organic waste (POW) and the denitrification process with obtained liquid were investigated. The most volatile fatty acids (VFAs) production was realized with the fermentation liquid of food waste (FL-FW). Increasing substrate tended to lower the proportion of VFAs and acetic acid in FL-FW. Under the optimum conditions of FL-FW carbon source, carbon to nitrogen ratio 7, and temperature 30 ℃, the removal efficiency of nitrate nitrogen reached 99.23% within 4 h. The sludge settleability and microbial activity were significantly enhanced, contributing to the actual sewage a promotional removal of organics (95.84%) and nitrogen (70.31%) with the supplementation of FL-FW. High addition ratio would cause more degradation of refractory organics, which confirmed the feasibility of using FL-FW as a cost-efficient carbon source for the denitrification.

Bioelectrochemical system as an innovative technology for treatment of produced water from oil and gas industry: A review

Disposal of the high volume of produced water (PW) is a big challenge to the oil and gas industry. High cost of conventional treatment facilities, increasing energy prices and environmental concern had focused governments and the industry itself on more efficient treatment methods. Bioelectrochemical system (BES) has attracted the attention of researchers because it represents a sustainable way to treat wastewater. This is the first review that summarizes the progress done in PW-fed BESs with a critical analysis of the parameters that influence their performances. Inoculum, temperature, hydraulic retention time, external resistance, and the use of real or synthetic produced water were found to be deeply related to the performance of BES. Microbial fuel cells are the most analyzed BES in this field followed by different types of microbial desalination cells. High concentration of sulfates in PW suggests that most of hydrocarbons are removed mainly by using sulfates as terminal electron acceptor (TEA), but other TEAs such as nitrate or metals can also be employed. The use of real PW as feed in experiments is highly recommended because biofilms when using synthetic PW are not the same. This review is believed to be helpful in guiding the research directions on the use of BES for PW treatment, and to speed up the practical application of BES technology in oil and gas industry.

Technical, economic and environmental feasibility of resource recovery technologies from wastewater

An enormous amount of wastewater is generated across the world from different industrial or municipal sectors. Traditional wastewater treatment plants (WWTP) have primarily focused on the treatment of wastewater rather than the recovery of valuable resources. A shift from a linear to a circular economy may offer a unique platform for recovering valuable resources including energy, nutrients, and high-value goods from wastewater. However, transitioning from conventional frameworks to sustainable WWT systems remains a significant challenge. Thus, this review paper focuses on the avenues of resource recovery from WWTPs, by evaluating the potential for nutrients, water, and energy recovery from different types of wastewaters and sewage sludge. It discusses in detail a variety of available and advanced technologies for resource recovery. Further, the feasibility of these technologies from a sustainable standpoint is discussed, covering the technical, economic, and environmental facets.

Engineering Wired Life: Synthetic Biology for Electroactive Bacteria

Electroactive bacteria produce or consume electrical current by moving electrons to and from extracellular acceptors and donors. This specialized process, known as extracellular electron transfer, relies on pathways composed of redox active proteins and biomolecules and has enabled technologies ranging from harvesting energy on the sea floor, to chemical sensing, to carbon capture. Harnessing and controlling extracellular electron transfer pathways using bioengineering and synthetic biology promises to heighten the limits of established technologies and open doors to new possibilities. In this review, we provide an overview of recent advancements in genetic tools for manipulating native electroactive bacteria to control extracellular electron transfer. After reviewing electron transfer pathways in natively electroactive organisms, we examine lessons learned from the introduction of extracellular electron transfer pathways into Escherichia coli. We conclude by presenting challenges to future efforts and give examples of opportunities to bioengineer microbes for electrochemical applications.

Living Bacteria Directly Embedded into Electrospun Nanofibers: Design of New Anode for Bio-Electrochemical Systems

The aim of this work is the optimization of electrospun polymeric nanofibers as an ideal reservoir of mixed electroactive consortia suitable to be used as anodes in Single Chamber Microbial Fuel Cells (SCMFCs). To reach this goal the microorganisms are directly embedded into properly designed nanofibers during the electrospinning process, obtaining so called nanofiber-based bio-composite (bio-NFs). This research approach allowed for the designing of an advanced nanostructured scaffold, able to block and store the living microorganisms inside the nanofibers and release them only after exposure to water-based solutions and electrolytes. To reach this goal, a water-based polymeric solution, containing 5 wt% of polyethylene oxide (PEO) and 10 wt% of environmental microorganisms, is used as the initial polymeric solution for the electrospinning process. PEO is selected as the water-soluble polymer to ensure the formation of nanofiber mats offering features of biocompatibility for bacteria proliferation, environment-friendliness and, high ionic conductivity. In the present work, bio-NFs, based on living microorganisms directly encapsulated into the PEO nanofiber mats, were analyzed and compared to PEO-NFs made of PEO only. Scanning electron microscopy allowed researchers to confirm the rise of a typical morphology for bio-NFs, evidencing the microorganisms’ distribution inside them, as confirmed by fluorescence optical microscopy. Moreover, the latter technique, combined with optical density measurements, allowed for demonstrating that after electrospinning, the processed microorganisms preserved their proliferation capability, and their metabolic activity after exposure to the water-based electrolyte. To demonstrate that the energy-production functionality of exo-electrogenic microorganisms was preserved after the electrospinning process, the novel designed nanomaterials, were directly deposited onto carbon paper (CP), and were applied as anode electrodes in Single Chamber Microbial Fuel Cells (SCMFCs). It was possible to appreciate that the maximum power density reached by bio-NFs, which resulted in being double of the ones achieved with PEO-NFs and bare CP. SCMFCs with bio-NFs applied as anodic electrodes reached a current density value, close to (250 ± 5.2) mA m⁻², which resulted in being stable over time and was comparable with the one obtained with carbon-based electrode, thus confirming the good performance of the whole device.

A review of the bioelectrochemical system as an emerging versatile technology for reduction of antibiotic resistance genes

Antibiotic contamination and the resulting resistance genes have attracted worldwide attention because of the extensive overuse and abuse of antibiotics, which seriously affects the environment as well as human health. Bioelectrochemical system (BES), a potential avenue to be explored, can alleviate antibiotic pollution and reduce antibiotic resistance genes (ARGs). This review mainly focuses on analyzing the possible reasons for the good performance of ARG reduction by BESs and potential ways to improve its performance on the basis of revealing the generation and transmission of ARGs in BES. This system reduces ARGs through two pathways: (1) the contribution of BES to the low selection pressure of ARGs caused by the efficient removal of antibiotics, and (2) inhibition of ARG transmission caused by low sludge yield. To promote the reduction of ARGs, incorporating additives, improving the removal rate of antibiotics by adjusting the environmental conditions, and controlling the microbial community in BES are proposed. Furthermore, this review also provides an overview of bioelectrochemical coupling systems including the BES coupled with the Fenton system, BES coupled with constructed wetland, and BES coupled with photocatalysis, which demonstrates that this method is applicable in different situations and conditions and provides inspiration to improve these systems to control ARGs. Finally, the challenges and outlooks are addressed, which is constructive for the development of technologies for antibiotic and ARG contamination remediation and blocking risk migration.

Bacterial signalling mechanism: An innovative microbial intervention with multifaceted applications in microbial electrochemical technologies: A review

Microbial electrochemical technologies (METs) are a set of inventive tools that generate value-added by-products with concomitant wastewater remediation. However, due to the bottlenecks, like higher fabrication cost and inferior yield of resources, these inventive METs are still devoid of successful field-scale implementation. In this regard, application of quorum sensing (QS) mechanism to improve the power generation of the METs has gained adequate attention. The QS is an intercellular signalling mechanism that controls the bacterial social network in its vicinity via the synthesis of diffusible signal molecules labelled as auto inducers, thus ameliorating yield of valuables produced through METs. This state-of-the-art review elucidates different types of QS molecules and their working mechanism with the special focus on the widespread application of QS in the field of METs for their performance enhancement. Thus, this review intends to guide the researchers in rendering scalability to METs by integrating innovative QS mechanisms into them.

Current Progress of Interfacing Organic Semiconducting Materials with Bacteria

Microbial bioelectronics require interfacing microorganisms with electrodes. The resulting abiotic/biotic platforms provide the basis of a range of technologies, including energy conversion and diagnostic assays. Organic semiconductors (OSCs) provide a unique strategy to modulate the interfaces between microbial systems and external electrodes, thereby improving the performance of these incipient technologies. In this review, we explore recent progress in the field on how OSCs, and related materials capable of charge transport, are being used within the context of microbial systems, and more specifically bacteria. We begin by examining the electrochemical communication modes in bacteria and the biological basis for charge transport. Different types of synthetic organic materials that have been designed and synthesized for interfacing and interrogating bacteria are discussed next, followed by the most commonly used characterization techniques for evaluating transport in microbial, synthetic, and hybrid systems. A range of applications is subsequently examined, including biological sensors and energy conversion systems. The review concludes by summarizing what has been accomplished so far and suggests future design approaches for OSC bioelectronics materials and technologies that hybridize characteristic properties of microbial and OSC systems.

Promoting Extracellular Electron Transfer of Shewanella oneidensis MR-1 by Optimizing the Periplasmic Cytochrome c Network

The low efficiency of extracellular electron transfer (EET) is a major bottleneck for Shewanella oneidensis MR-1 acting as an electroactive biocatalyst in bioelectrochemical systems. Although it is well established that a periplasmic c-type cytochrome (c-Cyt) network plays a critical role in regulating EET efficiency, the understanding of the network in terms of structure and electron transfer activity is obscure and partial. In this work, we attempted to systematically investigate the impacts of the network components on EET in their absence and overproduction individually in microbial fuel cell (MFC). We found that overexpression of c-Cyt CctA leads to accelerated electron transfer between CymA and the Mtr system, which function as the primary quinol oxidase and the outer-membrane (OM) electron hub in EET. In contrast, NapB, FccA, and TsdB in excess severely impaired EET, reducing EET capacity in MFC by more than 50%. Based on the results from both strategies, a series of engineered strains lacking FccA, NapB, and TsdB in combination while overproducing CctA were tested for a maximally optimized c-Cyt network. A strain depleted of all NapB, FccA, and TsdB with CctA overproduction achieved the highest maximum power density in MFCs (436.5 mW/m²), ∼3.62-fold higher than that of wild type (WT). By revealing that optimization of periplasmic c-Cyt composition is a practical strategy for improving EET efficiency, our work underscores the importance in understanding physiological and electrochemical characteristics of c-Cyts involved in EET.

Combined phyto-microbial-electrochemical system enhanced the removal of petroleum hydrocarbons from soil: A profundity remediation strategy

The soil contaminated by petroleum hydrocarbons has been a global environmental problem and its remediation is urgent. A combined phyto-microbial-electrochemical system (PMES) was constructed to repair the oil-contaminated soil in this study. During the 42-day operation time, a total petroleum hydrocarbons (TPHs) of 18.0 ± 3.0% were removed from PMES, which increased by 414% compared with the control group (CK1). The supervision of physicochemical properties of pore water in soil exhibited an enhanced microbial consumption of the total organic carbon (TOC) and N source under the applied potential with the generation of bio-current. The microbial succession indicated that the Dietzia, Georgenia and Malbranchea possibly participated in the degradation and current output in PMES. And a collaborative network of potential degrading microorganisms including unclassified norank_f__JG30-KF-CM45 (in Chloroflexi), Dietzia and Malbranchea was discovered in PMES. While the functional communities of microorganism were re-enriched with the reconstructed interactions in the system which was started with the sterilized soil (S+MEC). The superiority of TPHs degradation in S+MEC compared to P + CK2 (removing the electrochemical effect relative to CK1) revealed the key role of external potential in regulating the degradation microflora. The study provided a strategy of the potential regulated phyto-microbial interaction for the removal of TPHs.

Response of Methanogen Communities to the Elevation of Cathode Potentials in Bioelectrochemical Reactors Amended with Magnetite

Electromethanogenesis refers to the process whereby methanogens utilize current for the reduction of CO₂ to CH₄. Setting low cathode potentials is essential for this process. In this study, we tested if magnetite, an iron oxide mineral widespread in the environment, can facilitate the adaptation of methanogen communities to the elevation of cathode potentials in electrochemical reactors. Two-chamber electrochemical reactors were constructed with inoculants obtained from paddy field soil. We elevated cathode potentials stepwise from the initial -0.6 V versus the standard hydrogen electrode (SHE) to -0.5 V and then to -0.4 V over the 130 days of acclimation. Only weak current consumption and CH₄ production were observed in the bioreactors without magnetite. However, significant current consumption and CH₄ production were recorded in the magnetite bioreactors. The robustness of electroactivity of the magnetite bioreactors was not affected by the elevation of cathode potentials from -0.6 V to -0.4 V. However, the current consumption and CH₄ production were halted in the bioreactors without magnetite when the cathode potentials were elevated to -0.4 V. Methanogens related to Methanospirillum were enriched on the cathode surfaces of magnetite bioreactors at -0.4 V, while Methanosarcina relatively dominated in the bioreactors without magnetite. Methanobacterium also increased in the magnetite bioreactors but stayed off electrodes at -0.4 V. Apparently, the magnetite greatly facilitates the development of biocathodes, and it appears that with the aid of magnetite, Methanospirillum spp. can adapt to the high cathode potentials, performing efficient electromethanogenesis. IMPORTANCE Converting CO₂ to CH₄ through bioelectrochemistry is a promising approach to the development of green energy biotechnology. This process, however, requires low cathode potentials, which entails a cost. In this study, we tested if magnetite, a conductive iron mineral, can facilitate the adaptation of methanogens to the elevation of cathode potentials. In two-chamber reactors constructed by using inoculants obtained from paddy field soil, biocathodes developed robustly in the presence of magnetite, whereas only weak activities in CH₄ production and current consumption were observed in the bioreactors without magnetite. The elevation of cathode potentials did not affect the robustness of electroactivity of the magnetite bioreactors over the 130 days of acclimation. Methanospirillum strains were identified as the key methanogens associated with the cathode surfaces during the operation at high potentials. The findings reported in this study shed new light on the adaptation of methanogen communities to the elevated cathode potentials in the presence of magnetite.

Promoting the anode performance of microbial fuel cells with nano-molybdenum disulfide/carbon nanotubes composite catalyst

The design and manufacture of advanced anode materials with superior quality are significant for assembling high-performance microbial fuel cells (MFCs). The present study aims to investigate the synergistic effect of MoS₂/CNTs nanocomposite as a novel anode-modifying material of MFCs. XRD, XPS, SEM, TEM and electrochemical analyses were performed to confirm the nanocomposite, to understand the morphology and to study the electrochemical properties of the modified electrodes. The performance of the MoS₂/CNTs/carbon paper (CP)-MFCs was investigated and compared with that of MoS₂/CP-MFCs, CNTs/CP-MFCs and CP-MFCs. The densest biofilm was formed on MoS₂/CNTs-modified anode compared to MoS₂/CP, CNTs/CP and CP anode, and MFCs with MoS₂/CNTs-modified anodes achieved the maximum power density of 645 ± 32 mW m^-2, which is three times greater than MFCs with bare carbon paper anodes (213 ± 10 mW m^-2). These results demonstrate that the synthesized MoS₂/CNTs nanocomposite could be exploited as an efficient anode catalyst for improving the performance of MFCs.

Bioenergy from dairy manure: technologies, challenges and opportunities

Dairy manure (DM) is a kind of cheap cellulosic biomass resource which includes lignocellulose and mineral nutrients. Random stacks not only leads damage to the environment, but also results in waste of natural resources. The traditional ways to use DM include returning it to the soil or acting as a fertilizer, which could reduce environmental pollution to some extent. However, the resource utilization rate is not high and socio-economic performance is not utilized. To expand the application of DM, more and more attention has been paid to explore its potential as bioenergy or bio-chemicals production. This article presented a comprehensive review of different types of bioenergy production from DM and provided a general overview for bioenergy production. Importantly, this paper discussed potentials of DM as candidate feedstocks not only for biogas, bioethanol, biohydrogen, microbial fuel cell, lactic acid, and fumaric acid production by microbial technology, but also for bio-oil and biochar production through apyrolysis process. Additionally, the use of manure for replacing freshwater or nutrients for algae cultivation and cellulase production were also discussed. Overall, DM could be a novel suitable material for future biorefinery. Importantly, considerable efforts and further extensive research on overcoming technical bottlenecks like pretreatment, the effective release of fermentable sugars, the absence of robust organisms for fermentation, energy balance, and life cycle assessment should be needed to develop a comprehensive biorefinery model.

Enhancing stability and resilience of electromethanogenesis system by acclimating biocathode with intermittent step-up voltage

Electromethanogenesis (EMG) system could efficiently convert CO₂ to CH₄ by using excess renewable electricity. However, the fluctuation and interruption of renewable electricity will adversely affect the biocathode and therefore the CH₄ production of the EMG system. In this work, a novel biocathode acclimation strategy with intermittent step-up voltage (ISUV) was proposed to improve the stability and resilience of the EMG system against the unstable input of renewable power. Compared with the intermittent application of constant voltage (IACV), the ISUV increased the rate of CH₄ production by 11.7 times with the improvement of the stability and resilience by 56% and 500%, respectively. Morphology and microflora structure analysis revealed that the biofilm enriched with ISUV exhibited a compact microflora structure with high-density cells and nanowires interconnected. This study provided a novel effective strategy to regulate the biofilm structure and enhance the performance of the EMG system.

The Implications of Membranes Used as Separators in Microbial Fuel Cells

Microbial fuel cells (MFCs) are electrochemical devices focused on bioenergy generation and organic matter removal carried out by microorganisms under anoxic environments. In these types of systems, the anodic oxidation reaction is catalyzed by anaerobic microorganisms, while the cathodic reduction reaction can be carried out biotically or abiotically. Membranes as separators in MFCs are the primary requirements for optimal electrochemical and microbiological performance. MFC configuration and operation are similar to those of proton-exchange membrane fuel cells (PEMFCs)-both having at least one anode and one cathode split by a membrane or separator. The Nafion® 117 (NF-117) membrane, made from perfluorosulfonic acid, is a membrane used as a separator in PEMFCs. By analogy of the operation between electrochemical systems and MFCs, NF-117 membranes have been widely used as separators in MFCs. The main disadvantage of this type of membrane is its high cost; membranes in MFCs can represent up to 60% of the MFC's total cost. This is one of the challenges in scaling up MFCs: finding alternative membranes or separators with low cost and good electrochemical characteristics. The aim of this work is to critically review state-of-the-art membranes and separators used in MFCs. The scope of this review includes: (i) membrane functions in MFCs, (ii) most-used membranes, (iii) membrane cost and efficiency, and (iv) membrane-less MFCs. Currently, there are at least 20 different membranes or separators proposed and evaluated for MFCs, from basic salt bridges to advanced synthetic polymer-based membranes, including ceramic and unconventional separator materials. Studies focusing on either low cost or the use of natural polymers for proton-exchange membranes (PEM) are still scarce. Alternatively, in some works, MFCs have been operated without membranes; however, significant decrements in Coulombic efficiency were found. As the type of membrane affects the performance and total cost of MFCs, it is recommended that research efforts are increased in order to develop new, more economic membranes that exhibit favorable properties and allow for satisfactory cell performance at the same time. The current state of the art of membranes for MFCs addressed in this review will undoubtedly serve as a key insight for future research related to this topic.

Emerging bioelectrochemical technologies for biogas production and upgrading in cascading circular bioenergy systems

Biomethane is suggested as an advanced biofuel for the hard-to-abate sectors such as heavy transport. However, future systems that optimize the resource and production of biomethane have yet to be definitively defined. This paper assesses the opportunity of integrating anaerobic digestion (AD) with three emerging bioelectrochemical technologies in a circular cascading bioeconomy, including for power-to-gas AD (P2G-AD), microbial electrolysis cell AD (MEC-AD), and AD microbial electrosynthesis (AD-MES). The mass and energy flow of the three bioelectrochemical systems are compared with the conventional AD amine scrubber system depending on the availability of renewable electricity. An energy balance assessment indicates that P2G-AD, MEC-AD, and AD-MES circular cascading bioelectrochemical systems gain positive energy outputs by using electricity that would have been curtailed or constrained (equivalent to a primary energy factor of zero). This analysis of technological innovation, aids in the design of future cascading circular biosystems to produce sustainable advanced biofuels.

Label-Free Probing of Electron Transfer Kinetics of Single Microbial Cells on a Single-Layer Graphene via Structural Color Microscopy

Studies of electron transfer at the population level veil the nature of the cell itself; however, in situ probing of the electron transfer dynamics of individual cells is still challenging. Here we propose label-free structural color microscopy for this aim. We demonstrate that Shewanella oneidensis MR-1 cells show unique structural color scattering, changing with the redox state of cytochrome complexes in the outer membrane. It enables quantitatively and noninvasive studies of electron transfer in single microbial cells during bioelectrochemical activities, such as extracellular electron transfer (EET) on a transparent single-layer graphene electrode. Increasing the applied potential leads to the associated EET current, accompanied by more oxidized cytochromes. The high spatiotemporal resolution of the proposed method not only demonstrates the large diversity in EET activity among microbial cells but also reveals the subcellular asymmetric distribution of active cytochromes in a single cell. We anticipate that it provides a potential platform for further exploring the electron transfer mechanism of subcellular structure.

Effect of applied voltage on membrane fouling in the amplifying anaerobic electrochemical membrane bioreactor for long-term operation

A novel and amplifying anaerobic electrochemical membrane bioreactor (AnEMBR, R2) was constructed and operated for a long time (204 days) with synthetic glucose solution having an average chemical oxygen demand (COD) of 315 mg L⁻¹, at different applied voltages and room temperatures. More than twice sodium bicarbonate was added for maintaining a pH of around 6.7 in the supernatant of the reactor R2, close to that of a control reactor called anaerobic membrane bioreactor (AnMBR, R1), after 138 days. And the transmembrane pressure (TMP) for the R2 system was only 0.534 bar at the end of operation and 0.615 bar for the R1 system. Although the electrostatic repulsion force contributed to pushing away the pollutants (proteins, polysaccharose and inorganic salt deposits, and so on), more microorganisms adsorbed and accumulated on the membrane surface after the whole operation, which might result in a rapid increase in membrane filtration resistance in the long-term operation. There were much more exoelectrogenic bacteria, mainly Betaproteobacteria, Deltaproteobacteria and Grammaproteobacteria, on the cathode and the dominant methanogen Methanothrix content on the cathode was three times higher than the AnMBR. The study provides an important theoretical foundation for the application of AnEMBR technology in the treatment of low organic strength wastewater.

A novel and amplifying anaerobic electrochemical membrane bioreactor was constructed and operated for a long time (204 days) with synthetic glucose solution having an average chemical oxygen demand (COD) of 315 mg L⁻¹, at different applied voltages and room temperatures.

Silver nanoparticles boost charge-extraction efficiency in Shewanella microbial fuel cells

[Figure: see text].

Improving the anode performance of microbial fuel cell with carbon nanotubes supported cobalt phosphate catalyst

Microbial fuel cell (MFC) is a sustainable technology that can convert waste to energy by harnessing the power of exoelectrogenic bacteria. However, the poor biocompatibility and low electrocatalytic activities of surface usually cause weak bacterial adhesion and low electron transfer efficiency, which seriously hampers the development of MFCs. Herein, a novel carbon nanotube supported cobalt phosphate (CNT/Co-Pi) electrode is fabricated by assembling CNTs on carbon cloth, followed by the electrodeposition of Co-Pi catalyst. The deposited amorphous Co-Pi thin film contains phosphate and the cobalt ions of multiple oxidation states. The hydrophilic phosphate can promote the adhesion of microorganisms on electrode. The strong conversion ability of multiple states of cobalt offers excellent electrocatalytic activity for the electron transfer across biotic/abiotic interface. Therefore, the highly conductive CNTs substrate, along with the Co-Pi catalyst, provide an effective electron transfer between the electrogenic bacteria and the electrode, which endows MFC high power densities up to 1200 mW m^-2. Our work has demonstrated for the first time that CNT/Co-Pi catalyst can promote the interfacial electron transfer between electrogenic bacteria and electrode, and highlighted the application potentials of Co-Pi as an anode catalyst for the fabrication of high performance MFC anodes.

Modified cobalt-manganese oxide-coated carbon felt anodes: an available method to improve the performance of microbial fuel cells

The novel MnCo₂O₄ (MCO/CF), CNTs-MnCo₂O₄ (CNTs-MCO/CF) and MnFe₂O₄-MnCo₂O₄ (MFO-MCO/CF) electrodes were prepared on carbon felt (CF) by simple hydrothermal and coating method as anodes for MFC. The modified anodes combine the electrocatalytic properties of transition metal oxides (TMOs), the high electrical conductivity of CNTs and the good biocompatibility of CF. These anodes play a synergistically role in the synthesis of structural, to realize high-efficiency electron transfer, low resistance and sufficient space for microbial colonization, while also ensuring high power density. The maximum power density of the composite electrodes CNTs-MCO/CF and MFO-MCO/CF were 4268 mW/m³ and 3660 mW/m³, respectively. The synergistic effect of multi-component effectively improves the performance of MFC. This work not only offers a good design and preparation concept for functional TMOs composite electrodes, but also provides an important guide for the fabrication of CNTs-doped MFC anodes.

Wiring Up Along Electrodes for Biofilm Formation

Millimeter-length cables of bacteria were discovered growing along a graphite-rod electrode serving as an anode of a microbial electrolysis cell (MEC). The MEC had been inoculated with a culture of Fe-reducing microorganisms enriched from a polluted river sediment (Reconquista river, Argentina) and was operated at laboratory controlled conditions for 18 days at an anode poised potential of 240 mV (vs. Ag/AgCl), followed by 23 days at 480 mV (vs. Ag/AgCl). Anode samples were collected for scanning electron microscopy, phylogenetic and electrochemical analyses. The cables were composed of a succession of bacteria covered by a membranous sheath and were distinct from the known "cable-bacteria" (family Desulfobulbaceae). Apparently, the formation of the cables began with the interaction of the cells via nanotubes mostly located at the cell poles. The cables seemed to be further widened by the fusion between them. 16S rRNA gene sequence analysis confirmed the presence of a microbial community composed of six genera, including Shewanella, a well-characterized electrogenic bacteria. The formation of the cables might be a way of colonizing a polarized surface, as determined by the observation of electrodes extracted at different times of MEC operation. Since the cables of bacteria were distinct from any previously described, the results suggest that bacteria capable of forming cables are more diverse in nature than already thought. This diversity might render different electrical properties that could be exploited for various applications.

Treatment of fish market wastewater and energy production using halophiles in air cathode microbial fuel cell

The present study is aimed to treat the fish market wastewater coupled with electricity production using halophiles in microbial fuel cell (MFC) technology under saline condition (4.6%). Halophilic consortium obtained from desalination plant brine water was used in the lab scale air cathode microbial fuel cell (ACMFC) reactor equipped with carbon brush and carbon cloth as anode and cathode. ACMFC (260 mL capacity) was operated with fish market saline wastewater at different organic load (OL) from 0.41 to 2.01 g COD/L with 20 day HRT (Hydraulic Retention Time). Total chemical oxygen demand (TCOD) removal at OL 0.41, 0.82 and 1.21 g COD/L was 68%, 77% and 84% in ACMFC. Correspondingly, soluble chemical oxygen demand (SCOD) removal was 63%, 74% and 81% respectively. The optimized OL for the treatment of fish market wastewater was 1.62 g COD/L, where the TCOD (90%), SCOD (88%), TSS (Total Suspended Solids) removal of 71% coupled with power generation of 902 mV (Power density 420 mW/m², Current density 550 mA/m²) was recorded. Columbic efficiency at OL 0.41 g COD/L was 56% and declined at OL 0.82, 1.21, 1.62 and 2.01 g COD/L to 48%, 39%, 29% and 17%. Increment in OL to 2.01 g COD/L revealed decrease in TCOD (64%), SCOD (60%), TSS (45%) removal and energy production. The bacterial strains present in the halophilic consortium were Ochrobactrum, Marinobacter, Bacillus, Rhodococcus, Flavobacterium, Alicyclobacillus, Pseudomonas, Martelella, Stenotrophomonas, Xanthobacter, and Microbacterium. High dominance of Ochrobactrum, Marinobacter and Bacillus was observed at optimized OL of 1.62 g COD/L in ACMFC. Further research on pilot scale MFC lead the way to technology transfer for the treatment of wastewater with corresponding energy production in industrial sector.

Evidence of a Streamlined Extracellular Electron Transfer Pathway from Biofilm Structure, Metabolic Stratification, and Long-Range Electron Transfer Parameters

A strain of Geobacter sulfurreducens, an organism capable of respiring solid extracellular substrates, lacking four of five outer membrane cytochrome complexes (extABCD⁺ strain) grows faster and produces greater current density than the wild type grown under identical conditions. To understand cellular and biofilm modifications in the extABCD⁺ strain responsible for this increased performance, biofilms grown using electrodes as terminal electron acceptors were sectioned and imaged using electron microscopy to determine changes in thickness and cell density, while parallel biofilms incubated in the presence of nitrogen and carbon isotopes were analyzed using NanoSIMS (nanoscale secondary ion mass spectrometry) to quantify and localize anabolic activity. Long-distance electron transfer parameters were measured for wild-type and extABCD⁺ biofilms spanning 5-μm gaps. Our results reveal that extABCD⁺ biofilms achieved higher current densities through the additive effects of denser cell packing close to the electrode (based on electron microscopy), combined with higher metabolic rates per cell compared to the wild type (based on increased rates of ¹⁵N incorporation). We also observed an increased rate of electron transfer through extABCD⁺ versus wild-type biofilms, suggesting that denser biofilms resulting from the deletion of unnecessary multiheme cytochromes streamline electron transfer to electrodes. The combination of imaging, physiological, and electrochemical data confirms that engineered electrogenic bacteria are capable of producing more current per cell and, in combination with higher biofilm density and electron diffusion rates, can produce a higher final current density than the wild type.

IMPORTANCE Current-producing biofilms in microbial electrochemical systems could potentially sustain technologies ranging from wastewater treatment to bioproduction of electricity if the maximum current produced could be increased and current production start-up times after inoculation could be reduced. Enhancing the current output of microbial electrochemical systems has been mostly approached by engineering physical components of reactors and electrodes. Here, we show that biofilms formed by a Geobacter sulfurreducens strain producing ∼1.4× higher current than the wild type results from a combination of denser cell packing and higher anabolic activity, enabled by an increased rate of electron diffusion through the biofilms. Our results confirm that it is possible to engineer electrode-specific G. sulfurreducens strains with both faster growth on electrodes and streamlined electron transfer pathways for enhanced current production.

Microbial Fuel Cell as a Bioelectrochemical Sensor of Nitrite Ions

The deteriorating environmental quality requires a rapid in situ real-time monitoring of toxic compounds in environment including water and wastewater. One of the most toxic nitrogen-containing ions is nitrite ion, therefore, it is particularly important to ensure that nitrite ions are completely absent in surface and ground waters as well as in wastewater or, at least, their concentration does not exceed permissible levels. However, no selective ion electrode, which would enable continuous measurement of nitrite ion concentration in wastewater by bioelectrochemical sensor, is available. Microbial fuel cell (MFC)-based biosensor offers a sustainable low-cost alternative to the monitoring by periodic sampling for laboratory testing. It has been determined, that at low (0.01–0.1 mg·L−1) and moderate (1.0–10 mg·L−1) concentration of nitrite ions in anolyte-model wastewater, the voltage drop in MFC linearly depends on the logarithm of nitrite ion concentration of proving the potential of the application of MFC-based biosensor for the quantitative monitoring of nitrite ion concentration in wastewater and other surface water. Higher concentrations (100–1000 mg·L−1) of nitrite ions in anolyte-model wastewater could not be accurately quantified due to a significant drop in MFC voltage. In this case MFC can potentially serve as a bioelectrochemical early warning device for extremely high nitrite pollution.

Recent advances in the improvement of bi-directional electron transfer between abiotic/biotic interfaces in electron-assisted biosynthesis system

As an important biosynthesis technology, electron-assisted biosynthesis (EABS) system can utilize exogenous electrons to regulate the metabolic network of microorganisms, realizing the biosynthesis of high value-added chemicals and CO₂ fixation. Electrons play crucial roles as the energy carriers in the EABS process. In fact, efficient interfacial electron transfer (ET) is the decisive factor to realize the rapid energy exchange, thus stimulating the biosynthesis of target metabolic products. However, due to the interfacial resistance of ET between the abiotic solid electrode and biotic microbial cells, the low efficiency of interfacial ET has become a major bottleneck, further limiting the practical application of EABS system. As the cell membrane is insulated, even the cell membrane embedded electron conduit (no matter cytochromes or channel protein for shuttle transferring) to increase the cell membrane conductivity, the ET between membrane electron conduit and electrode surface is kinetically restricted. In this review, the pathway of bi-directional interfacial ET in EABS system was summarized. Furthermore, we reviewed representative milestones and advances in both the anode outward interfacial ET (from organism to electrode) and cathode inward interfacial ET (from electrode to organism). Here, new insights from the perspectives of material science and synthetic biology were also proposed, which were expected to provide some innovative opinions and ideas for the following in-depth studies.

Uniform Distribution of Pd on GO-C Catalysts for Enhancing the Performance of Air Cathode Microbial Fuel Cell

Metal, as a high-performance electrode catalyst, is a research hotspot in the construction of a high-performance microbial fuel cell (MFC). However, metal catalyst nanoparticles and their dispersed carriers are prone to aggregation, producing catalytic electrodes with inferior qualities. In this study, Pd is uniformly dispersed on the graphene framework supported by carbon black to form nanocomposite catalysts (Pd/GO-C catalysts). The effect of the palladium loading amount in the catalyst on the catalytic performance of the air cathode was further studied. The optimized metal loading afforded a reduced resistance and improved accessibility of Pd particles for the ORR. The maximum current output of the 0.250 Pd (mg/cm2) MFC was 1645 mA/m2, which is 4.2-fold higher than that of the carbon paper cathode. Overall, our findings provide a novel protocol for the preparation of high-efficient ORR catalyst for MFCs.

Effect of modified anode on bioenergy harvesting and nutrients removal in a microbial nutrient recovery cell

The microbial nutrient recovery cell i.e. modified microbial fuel cell containing a middle recovery chamber can be used to purify wastewater and remove valuable nutrients, while simultaneously generating electricity. The study investigated nutrient removal and microorganism interactions with carbon (CB- HT and CB- APTES) and stainless steel (SSB-HT) modified anodes used in microbial nutrient recovery cells. The removal efficiencies of ammonium ions were found higher in carbon-based CB-APTES (~98%) and CB-HT (~98.27%) systems in comparison to SSB-HT (~87.16%) system. On comparing further, the removal efficiencies of chemical oxygen demand (~99.5%) and total phosphorus (~99%) in CB- APTES system were superior to the cases of CB- HT, and SSB- HT systems. Besides, the CB-APTES based microbial fuel cell (MFC) displayed an average stable voltage of 0.5 V and a maximum power density of ~ 850 mW/m².

Excessive extracellular polymeric substances induced by organic shocks accelerate electron transfer of oxygen reducing biocathode

Electrotrophic bacteria on cathodes are promising substitutes to precious metals as oxygen reduction reaction catalysts in bioelectrochemical systems (BESs). Leading the anodic effluent to the biocathode has additional benefits of neutralizing pH and removing residual pollutants. However, the overflow of excessive organic pollutants inhibits the activity of autotrophic biocathodes. Adding glucose as an organic shock, we confirm that the startup time of biocathodes is initially prolonged by 1.2 times with a decrease in current. However, the currents inversely surpass the control in glucose-added BESs when the biofilm is mature, and the maximum current density increase by 5.5 times with a relatively stable performance. This increase is mainly attributed to the production of agglomerates dominated by polysaccharides and proteins as extracellular polymeric substances. These agglomerates wrap additional redox shuttles that accelerated the electron transfer between electrotrophic bacteria and the cathode. This study demonstrates for the first time that organic shocks enhance the electroactivity of autotrophic biocathodes and provides insights into the feedback mechanisms of electrotrophic microbial community to environmental changes.

How Comparable are Microbial Electrochemical Systems around the Globe? An Electrochemical and Microbiological Cross-Laboratory Study

A cross-laboratory study on microbial fuel cells (MFC) which involved different institutions around the world is presented. The study aims to assess the development of autochthone microbial pools enriched from domestic wastewater, cultivated in identical single-chamber MFCs, operated in the same way, thereby approaching the idea of developing common standards for MFCs. The MFCs are inoculated with domestic wastewater in different geographic locations. The acclimation stage and, consequently, the startup time are longer or shorter depending on the inoculum, but all MFCs reach similar maximum power outputs (55±22 μW cm-2 ) and COD removal efficiencies (87±9 %), despite the diversity of the bacterial communities. It is inferred that the MFC performance starts when the syntrophic interaction of fermentative and electrogenic bacteria stabilizes under anaerobic conditions at the anode. The generated power is mostly limited by electrolytic conductivity, electrode overpotentials, and an unbalanced external resistance. The enriched microbial consortia, although composed of different bacterial groups, share similar functions both on the anode and the cathode of the different MFCs, resulting in similar electrochemical output.

Liposoluble quinone promotes the reduction of hydrophobic mineral and extracellular electron transfer of Shewanella oneidensis MR-1

A large number of reaction systems are composed of hydrophobic interfaces and microorganisms in natural environment. However, it is not clear how microorganisms adjust their breathing patterns and respond to hydrophobic interfaces. Here, Shewanella oneidensis MR-1 was used to reduce ferrihydrite of a hydrophobic surface. Through Fe(II) kinetic analysis, it was found that the reduction rate of hydrophobic ferrihydrite was 1.8 times that of hydrophilic one. The hydrophobic surface of the mineral hinders the way the electroactive microorganism uses the water-soluble electron mediator riboflavin for indirect electron transfer and promotes MR-1 to produce more liposoluble quinones. Ubiquinone can mediate electron transfer at the hydrophobic interface. Ubiquinone-30 (UQ-6) increases the reduction rate of hydrophobic ferrihydrite from 38.5 ± 4.4 to 52.2 ± 0.8 μM·h⁻¹. Based on the above experimental results, we propose that liposoluble electron mediator ubiquinone can act on the extracellular hydrophobic surface, proving that the metabolism of hydrophobic minerals is related to endogenous liposoluble quinones. Hydrophobic modification of minerals encourages electroactive microorganisms to adopt differentiated respiratory pathways. This finding helps in understanding the electron transfer behavior of the microbes at the hydrophobic interface and provides new ideas for the study of hydrophobic reactions that may occur in systems, such as soil and sediment.

•

Extracellular electron transfer can be regulated by wettability of mineral surface

•

Hydrophobic surface hinders the transport of water-soluble mediator riboflavin

•

Ubiquinone can mediate extracellular electron transfer at the hydrophobic interface

Enhanced mechanism of extracellular electron transfer between semiconducting minerals anatase and Pseudomonas aeruginosa PAO1 in euphotic zone

Focusing the marine euphotic zone, which is the pivotal region for interaction of solar light-mineral-microorganism and the elements cycle, we have conducted the research on the mechanism of semiconducting minerals promoting extracellular electron transfer with microorganisms in depth. Therein, anatase which is one of the most representative semiconducting minerals in marine euphotic zone was selected. The mineralogical characterization of anatase was identified by ESEM, AFM, EDS, Raman, XRD, and its semiconducting characteristics was determined by UV-Vis and Mott-Schottky plots. Determined by the electrochemical measurement of I-t curves, the photocurrent density of anatase was more prominent than dark current density. Pseudomonas aeruginosa PAO1 was widely distributed in the euphotic zone, and its mutants of operons deficient in biosynthesis pyocyanin (Δphz1Δphz2) and pili deficient (ΔpilA) were employed in this study. I-t curves indicated that both direct and indirect extracellular electron transfer processes occurred between anatase and PAO1. The indirect electron transfer depending on pyocyanin secreted by PAO1 was the main electron transfer mode. This work demonstrated the light-driven extracellular electron transfer and further revealed the photo-catalyzed mechanisms between anatase and PAO1 in marine euphotic zone.

Bioelectrochemical treatment of municipal solid waste landfill mature leachate and dairy wastewater as co-substrates

Despite solid wastes' landfill disposal limitation due to recent European legislation, landfill leachate disposal remains a significant problem and will be for many years in the future, since its production may persist for years after a site's closure. Among process technologies proposed for its treatment, microbial fuel cells (MFCs) can be effective, achieving both contaminant removal and simultaneous energy recovery. Start-up and operation of two dual-chamber MFCs with different electrodes' structure, fed with mature municipal solid waste landfill leachate, are reported in this study. Influent (a mix of dairy wastewater and mature landfill leachate at varying proportions) was fed to the anodic chambers of the units, under different conditions. The maximum COD removal efficiency achieved was 84.9% at low leachate/dairy mix, and 66.3% with 7.6% coulombic efficiency (CE) at a leachate/dairy ratio of 20%. Operational issues and effects of cells' architecture and electrode materials on systems' performance are analyzed and discussed.

Microbial Electrochemical Oxidation of Anaerobic Digestion Effluent From Treating HTC Process Water

Hydrothermal carbonization (HTC) is a promising technology for chemical and material synthesis. However, HTC produces not only valuable solid coal-materials but also yields process water (PW) with high chemical oxygen demand (COD) that requires extensive treatment. Anaerobic digestion (AD) has been used for initial treatment of HTC-PW, but the AD effluent is still high in COD and particles. Here, we show that microbial electrochemical technologies (MET) can be applied for COD removal from AD effluent of HTC-PW. Bioelectrochemical systems (BES) treating different shares of AD effluent from HTC-PW exhibited similar trends for current production. Thereby, maximum current densities of 0.24 mA cm−2 and COD removal of 65.4 ± 4.4% were reached (n = 3). Microbial community analysis showed that the genus Geobacter dominated anode biofilm and liquid phase of all reactors indicating its central role for COD oxidation and current generation.

Boosting the anode performance of microbial fuel cells with a bacteria-derived biological iron oxide/carbon nanocomposite catalyst

Modifying the electrodes of microbial fuel cells (MFCs) with iron oxides can improve the bacterial attachment performances and electrocatalytic activities for energy conversion, which is of significance in the fabrication of MFCs. However, the conventional modification methods usually result in the aggregation of iron sites, producing the electrodes of poor qualities. Herein, we report a novel method for the modification of electrochemical electrodes to boost the anode performance of MFC. The Shewanella precursor adhered on carbon felt electrode was directly carbonized to form a bacteria-derived biological iron oxide/carbon (Bio-FeOx/C) nanocomposite catalyst. The large spatial separation between the bacteria, as well as those between the iron containing proteins in the bacteria, deliver a highly dispersed Bio-FeOx/C nanocomposite with good electrocatalytic activities. The excellent microbial attachment performance and electron transfer rate of the Bio-FeOx/C modified electrode significantly promote the transfer of produced electrons between bacteria and electrode. Accordingly, the MFC with the Bio-FeOx/C electrode exhibits the maximum power density of 797.0 mW m^-2, much higher than that obtained with the conventional carbon felt anode (226.1 mW m^-2). Our works have paved a new avenue to the conversion of the natural bacterial precursors into active iron oxide nanoparticles as the anode catalyst of MFCs. The high catalytic activity of the prepared Bio-FeOx endows it great application potentials in the construction of high-performance electrodes.

A CMOS Multi-Modal Electrochemical and Impedance Cellular Sensing Array for Massively Paralleled Exoelectrogen Screening

The paper presents a 256-pixel CMOS sensor array with in-pixel dual electrochemical and impedance detection modalities for rapid, multi-dimensional characterization of exoelectrogens. The CMOS IC has 16 parallel readout channels, allowing it to perform multiple measurements with a high throughput and enable the chip to handle different samples simultaneously. The chip contains a total of 2 × 256 working electrodes of size 44 μm × 52 μm, along with 16 reference electrodes of dimensions 56 μm × 399 μm and 32 counter electrodes of dimensions 399 μm × 106 μm, which together facilitate the high resolution screening of the test samples. The chip was fabricated in a standard 130nm BiCMOS process. The on-chip electrodes are subjected to additional fabrication processes, including a critical Al-etch step that ensures the excellent biocompatibility and long-term reliability of the CMOS sensor array in bio-environment. The electrochemical sensing modality is verified by detecting the electroactive analyte NaFeEDTA and the exoelectrogenic Shewanella oneidensis MR-1 bacteria, illustrating the chip's ability to quantify the generated electrochemical current and distinguish between different analyte concentrations. The impedance measurements with the HEK-293 cancer cells cultured on-chip successfully capture the cell-to-surface adhesion information between the electrodes and the cancer cells. The reported CMOS sensor array outperforms the conventional discrete setups for exoelectrogen characterization in terms of spatial resolution and speed, which demonstrates the chip's potential to radically accelerate synthetic biology engineering.