Electrochemical impedance spectroscopy

Rapid degradation of 2,4-dichloronitrobenzene in single-chamber microbial electrolysis cell with pre-acclimated bioanode: A comprehensive assessment

2,4-dichloronitrobenzene (DClNB) as a typical refractory pollutant, exists in multifarious industrial wastewater widely and poses a serious threat to the environment. An ion exchange membrane (IEM)-free microbial electrolysis cell (MEC) with pre-acclimated bioanode was built and evaluated systematically for treatment of DClNB containing wastewater. Results showed that compared with the non-acclimated or IEM-equipped MECs, the pre-acclimated IEM-free MECs had the best DClNB removal efficiency of 91.3% under COD and DClNB loading rates of nearly 1000 kg m^-3 d^-1 and 100 g m^-3 d^-1. Both of anode pre-acclimation and IEM removal reduced the electron transfer resistance by 71.1 and 194.5 Ω, respectively. Compared to the pre-acclimated IEM-equipped MEC, the cathode current efficiency of pre-acclimated IEM-free MEC increased by 13.7%. Analysis of live/dead cell staining indicated that a higher proportion of live cells was observed in the acclimated anode biofilm (66.1% vs. 47.3%), and the detoxification of DClNB in the pre-acclimated IEM-free MECs was significantly better (p < 0.05) than those of non-acclimated or IEM-equipped MECs. This study contributes to the performance improvement of the MEC process for treatment of toxic industrial wastewater.

An Impedance Sensor in Detection of Immunoglobulin G with Interdigitated Electrodes on Flexible Substrate

Immunoassay plays an important role in the early screening and diagnosis of diseases. The use of electrochemical methods to realize the label-free, specific and rapid detection of antigens has attracted extensive attention from researchers. In this study, we realized the function of immunosensing and detection by lithography, the interdigitated gold electrode on the polyethylene naphthalate (PEN) membrane. Then, the gold electrode was biofunctionalized and the characterization was verified by atomic force microscopy, which was finally for the detection of mice IgG. This immunosensor has a low detection limit, with a broad linear detection range of 0.01–10 ng/mL. The results show that the electrochemical impedance sensor made of metal electrodes based on PEN flexible materials is suitable for immunoassay experiments. If this method could be proved by further studies, broad application prospects can be seen in routine immunoassays.

Dielectrophoretic analysis of the impact of isopropyl alcohol on the electric polarisability of Escherichia coli whole-cells

Whole-cell biocatalysts are versatile tools in (industrial) production processes; though, the effects that impact the efficiency are not fully understood yet. One main factor that affects whole-cell biocatalysts is the surrounding medium, which often consists of organic solvents due to low solubility of substrates in aqueous solutions. It is expected that organic solvents change the biophysical and biochemical properties of the whole-cell biocatalysts, e.g. by permeabilising the cell membrane, and thus analysis of these effects is of high importance. In this work, we present an analysis method to study the impact of organic solvents on whole-cell biocatalysts by means of dielectrophoresis. For instance, we evaluate the changes of the characteristic dielectrophoretic trapping ratio induced by incubation of Escherichia coli, serving as a model system, in an aqueous medium containing isopropyl alcohol. Therefore, we could evaluate the impact on the electric polarisability of the cells. For this purpose, a special microchannel device was designed and Escherichia coli cells were genetically modified to reliably synthesise a green fluorescent protein. We could demonstrate that our method was capable of revealing different responses to small changes in isopropyl alcohol concentration and incubation duration. Complementary spectrophotometric UV-Vis (ultraviolet-visible light) absorbance analysis of released NAD(P)+/NAD(P)H cofactor and proteins confirmed our results. Based on our results, we discuss the biophysical effects taking place during incubation. Graphical abstract.

Layer-by-layer deposition of bioactive layers on magnesium alloy stent materials to improve corrosion resistance and biocompatibility

Magnesium alloy is considered as one of the ideal cardiovascular stent materials owing to its good mechanical properties and biodegradability. However, the in vivo rapid degradation rate and the insufficient biocompatibility restrict its clinical applications. In this study, the magnesium alloy (AZ31B) was modified by combining the surface chemical treatment and in-situ self-assembly of 16-phosphonyl-hexadecanoic acid, followed by the immobilization of chitosan-functionalized graphene oxide (GOCS). Heparin (Hep) and GOCS were alternatively immobilized on the GOCS-modified surface through layer by layer (LBL) to construct the GOCS/Hep bioactive multilayer coating, and the corrosion resistance and biocompatibility were extensively explored. The results showed that the GOCS/Hep bioactive multilayer coating can endow magnesium alloys with an excellent in vitro corrosion resistance. The GOCS/Hep multilayer coating can significantly reduce the hemolysis rate and the platelet adhesion and activation, resulting in an excellent blood compatibility. In addition, the multilayer coating can not only enhance the adhesion and proliferation of the endothelial cells, but also promote the vascular endothelial growth factor (VEGF) and nitric oxide (NO) expression of the attached endothelial cells on the surfaces. Therefore, the method of the present study can be used to simultaneously control the corrosion resistance and improve the biocompatibility of the magnesium alloys, which is expected to promote the application of magnesium alloys in biomaterials or medical devices, especially cardiovascular stent.

•

The multilayer coating of GOCS and heparin was constructed on magnesium surface.

•

The coating can obviously improve the corrosion resistance of magnesium alloys.

•

The coating can enhance the hemocompatibility and endothelial cell growth behaviors.

Interpreting Dynamic Interfacial Changes at Carbon Fiber Microelectrodes Using Electrochemical Impedance Spectroscopy

Carbon-fiber microelectrodes are instrumental tools in neuroscience used for the electroanalysis of neurochemical dynamics and recordings of neural activity. However, performance is variable and dependent on fabrication strategies, the biological response to implantation, and the physical and chemical composition of the recording environment. This presents an analytical challenge, as electrode performance is difficult to quantitatively assess in situ, especially when electrodes are permanently implanted or cemented in place. We previously reported that electrode impedance directly impacts electrochemical performance for molecular sensing. In this work, we investigate the impacts of individual components of the electrochemical system on impedance. Equivalent circuit models for glass- and silica-insulated carbon-fiber microelectrodes were determined using electrochemical impedance spectroscopy (EIS). The models were validated based on the ability to assign individual circuit elements to physical properties of the electrochemical system. Investigations were performed to evaluate the utility of the models in providing feedback on how changes in ionic strength and carbon fiber material alter impedance properties. Finally, EIS measurements were used to investigate the electrode/solution interface prior to, during, and following implantation in live brain tissue. A significant increase in impedance and decrease in capacitance occur during tissue exposure and persist following implantation. Electrochemical conditioning, which occurs continually during fast-scan cyclic voltammetry recordings, etches and renews the carbon surface, mitigating these effects. Overall, the results establish EIS as a powerful method for characterization of carbon-fiber microelectrodes, providing unprecedented insight into how real-world factors affect the electrode/solution interface.

The Power of Assemblies at Interfaces: Nanosensor Platforms Based on Synthetic Receptor Membranes

Synthetic sensing materials (artificial receptors) are some of the most attractive components of chemical/biosensors because of their long-term stability and low cost of production. However, the strategy for the practical design of these materials toward specific molecular recognition in water is not established yet. For the construction of artificial material-based chemical/biosensors, the bottom-up assembly of these materials is one of the effective methods. This is because the driving forces of molecular recognition on the receptors could be enhanced by the integration of such kinds of materials at the 'interfaces', such as the boundary portion between the liquid and solid phases. Additionally, the molecular assembly of such self-assembled monolayers (SAMs) can easily be installed in transducer devices. Thus, we believe that nanosensor platforms that consist of synthetic receptor membranes on the transducer surfaces can be applied to powerful tools for high-throughput analyses of the required targets. In this review, we briefly summarize a comprehensive overview that includes the preparation techniques for molecular assemblies, the characterization methods of the interfaces, and a few examples of receptor assembly-based chemical/biosensing platforms on each transduction mechanism.

Electric Fields at Metal-Surfactant Interfaces: A Combined Vibrational Spectroscopy and Capacitance Study

Surfactants modulate interfacial processes. In electrochemical CO₂ reduction, cationic surfactants promote carbon product formation and suppress hydrogen evolution. The interfacial field produced by the surfactants affects the energetics of electrochemical intermediates, mandating their detailed understanding. We have used two complementary tools-vibrational Stark shift spectroscopy which probes interfacial fields at molecular length scales and electrochemical impedance spectroscopy (EIS) which probes the entire double layer-to study the electric fields at metal-surfactant interfaces. Using a nitrile as a probe, we found that at open-circuit potentials, cationic surfactants produce larger effective interfacial fields (∼-1.25 V/nm) when compared to anionic surfactants (∼0.4 V/nm). At a high bulk surfactant concentration, the surface field reaches a terminal value, suggesting the formation of a full layer, which is also supported by EIS. We propose an electrostatic model that explains these observations. Our results help in designing tailored surfactants for influencing electrochemical reactions via the interfacial field effect.

MicroRNAs in ovarian cancer and recent advances in the development of microRNA-based biosensors

Ovarian cancer is the most aggressive of all gynaecological malignancies and is the leading cause of cancer-associated mortality worldwide.

Advances in dynamically controlled catalytic reaction engineering

Dynamically forced input oscillations exhibit ability to surpass classical thermodynamic barriers through reactor operation and surface resonance.

Investigation to Minimize Electrochemical Impedance Spectroscopy Drift

Electrochemical impedance spectroscopy (EIS) is a technique used to characterize physiochemical processes, especially in the field of biosensors. However, EIS has been known to have reproducibility issues due to an inherent drift. When taking repeated measurements of the same exact solution using EIS, impedance measurements have an increasing trend which can be detailed by a linear slope. The reported EIS drift ranges from 0.11 to 5.5 Ω/min. We studied the drift to assist with future data interpretation and model fitting. We discovered the cleanliness and treatment of the working electrode effects EIS drift, and the minimization of the drift can occur by rinsing the working electrode in-between repeated runs.

Effective Wetting Area Based on Electrochemical Impedance Analysis: Hydrophilic Structured Surface

Wettability on nano/microstructured surfaces is gaining remarkable interest for a wide range of applications; however, little is known about the effective wetting area of the solid-liquid interface. In this study, the effect of wettability on electrochemical impedance was experimentally investigated to obtain a better understanding of the effective wetting area. We demonstrate that the water contact angle decreases significantly at hydrophilic surfaces with denser nano/microstructures. Based on the analysis of equivalent electrical circuits, we found that the electrochemical impedance decreases with reducing the water contact angle, showing a dependence on the effective wetting area, i.e., the real solid-liquid contact area. Also, the charge transfer resistance at low frequency was found to be the dominant parameter to estimate the effective wetting area at the solid-liquid interface.

Phage-based Electrochemical Sensors: A Review

Phages based electrochemical sensors have received much attention due to their high specificity, sensitivity and simplicity. Phages or bacteriophages provide natural affinity to their host bacteria cells and can serve as the recognition element for electrochemical sensors. It can also act as a tool for bacteria infection and lysis followed by detection of the released cell contents, such as enzymes and ions. In addition, possible detection of the other desired targets, such as antibodies have been demonstrated with phage display techniques. In this paper, the recent development of phage-based electrochemical sensors has been reviewed in terms of the different immobilization protocols and electrochemical detection techniques.

Implementation of Second-Generation Fourier Transform Electrochemical Impedance Spectroscopy with Commercial Potentiostat and Application to Time-Resolved Electrochemical Impedance Spectroscopy

We report the implementation of second-generation Fourier transform electrochemical impedance spectroscopy (2G FT-EIS) with commercial potentiostat. Although 2G FT-EIS based on chronoamperometry has several advantages of short measurement time and ability of time-resolved EIS, a special home-built electrochemical system is essential, which has been an obstacle to the wide application of 2G FT-EIS. Current commercial potentiostat and software, however, has sufficient power thanks to recent state-of-the art electronics and software industry. 2G FT-EIS requires two signals of time versus voltage and time versus current from chronoamperometry with a high sampling rate. In this work, auxiliary input of a commercial potentiostat was used to record voltage signal concomitant with typical chronoamperometry that consisted of time versus current. This simple approach enables the 2G EIS without expensive frequency response analyzer (FRA) and the complex home-built instrument. EISs with various charge transfer kinetics were investigated by the formation of a self-assembled monolayer (SAM) on Au with different chain lengths. More to the point, in situ time-resolved EISs during the SAM were obtained, demonstrating the ability of a commercial potentiostat for time-resolved EIS.

Microbial electrochemical technologies: Electronic circuitry and characterization tools

Microbial electrochemistry merges microbiology, electrochemistry and electronics to provide a set of technologies for environmental engineering applications. Understanding the electronic concepts is crucial for effectively adopting these systems, but the importance of electronic circuitry is often overlooked by microbial electrochemistry researchers. This review provides the background on the electronics and electrochemical concepts involved in the study of microorganisms interacting with electricity, and their applications in microbial electrochemical technology (MET). The potentiostat circuitry is described along with its working principles. Electrochemical analyses are presented together with the rational and parameters employed to study MET devices and electroactive microorganisms. Finally, future directions are delineated towards the adoption of MET, and the related electronics, in environmental engineering applications.

Development of novel MnO2 coated carbon felt cathode for microbial electroreduction of CO2 to biofuels

Fabrication of superior and cost-effective cathodic materials is vital in manufacturing sustainable microbial electrolysis cells (MECs) for biofuels production. In the present study, a novel manganese dioxide (MnO₂) coated felt cathode (Mn/CF) has been developed for MECs using electrodeposition method via potentiostat. MnO₂ is considered to encourage exogenous electron exchange and, in this way, improves the reduction of carbon dioxide (CO₂). MnO₂, as a cathodic catalyst, enhances the rate of biofuel production, electron transfer, and significantly reduces the cost of MECs. A maximum stabilized current density of 3.70 ± 0.5 mA/m² was obtained in case of MnO₂-coated Mn/CF based MEC, which was more than double the non-coated carbon felt (CF) cathode (1.70 ± 0.5 mA/m²). The dual chamber Mn/CF-MEC achieved the highest production rate of acetic acid (37.9 mmol/L) that was significantly higher (43.0%) in comparison to the non-coated CF-MEC. The cyclic voltammograms further verified the substantial enhancement in the electron transfer between the MnO₂ coated cathode and microbes. The obtained results demonstrate that MnO₂ interacted electrochemically with microbial cells and enhanced the extracellular electron transfer, therefore validating its potential role in biofuel production. The MnO₂ coated CF further offered higher electrode surface area and better electron transfer efficiency, suggesting its applicability in the large-scale MECs.

Non-faradaic electrochemical impedimetric profiling of procalcitonin and C-reactive protein as a dual marker biosensor for early sepsis detection

In this work, we demonstrate a robust, dual marker, biosensing strategy for specific and sensitive electrochemical response of Procalcitonin and C-reactive protein in complex body fluids such as human serum and whole blood for the detection of sepsis. Enhanced sensitivity is achieved by leveraging the physicochemical properties of zinc oxide at the electrode-solution interface. Characterization techniques such as SEM, EDAX, AFM, FTIR and fluorescence microscopy were performed to ensure a suitable biosensing surface. The characteristic biomolecular interactions between the target analyte and specific capture probe is quantified through unique frequency signatures using non-faradaic electrochemical impedance spectroscopy (EIS). The developed biosensor demonstrated a detection limit of 0.10 ng mL⁻¹ for PCT in human serum and whole blood with an R² of 0.99 and 0.98 respectively. CRP demonstrated a detection limit of 0.10 μg mL⁻¹ in human serum and whole blood with an R² of 0.90 and 0.98 respectively. Cross-reactivity analysis demonstrated robust selectivity to PCT and CRP with negligible interaction to non-specific biomolecules. The novel aspect of this technology is the ability to fine-tune individual biomarkers response owing to the optimal frequency tuning capability. The developed biosensor requires an ultra-low sample volume of 10 μL without the need for sample dilution for rapid analysis. We envision the developed dual marker biosensor to be useful as a sepsis-screening device for prognostic monitoring.

•

Ultra-sensitive, specific, low volume biosensor developed for rapid screening of host response biomarkers to detect sepsis.

•

EIS captures the interfacial changes within the electrical double layer due to the binding interaction of PCT & CRP.

•

Enhanced sensor response with a LOD of 0.10 ng mL⁻¹ for PCT and 0.10 μg mL⁻¹ for CRP and an R² of 0.99 in human serum & blood.

•

Biomolecular frequency tuning using electrochemical impedance spectroscopy enables multi-marker detection.

•

Developed dual marker biosensor demonstrates specific response towards target biomolecules.

Sodium Alginate Enabled Advanced Layered Manganese-Based Cathode for Sodium-Ion Batteries

Sodium-ion batteries (SIBs) are promising candidates applied to large-scale energy storage systems owing to abundant sodium resources and high economic efficiency. Layered manganese-based oxides as a prevailing cathode for sodium-ion batteries have been extensively studied, where doping or coating has been demonstrated to improve the electrochemical performance. However, the binder that tends to be the popular poly(vinylidene difluoride), is revealed to generate swellability upon cycling, leading to electrode material cracks and disconnection with current collectors. For the above issues, in this work, environmentally friendly sodium alginate is utilized as the aqueous binder in a conventional layered transition-metal oxide cathode P2-Na_2/3MnO₂ for SIBs. Through credible comparative experiments, sodium alginate is testified to play an essential role in suppressing cracks on the surface of materials, preventing surge in charge-transfer resistance and restraining detachment between electrode and current collector. Therefore, sodium alginate is proved to be an ideal binder to match with P2-Na_2/3MnO₂, where some issues existed before, as a promising cathode material with excellent performance and low cost. This study displays that improving battery performance by exploring suitable binder systems can equal or even exceed the performance improvement through modification of the material itself, and this perspective of enhancement should not be ignored.

Role of Defects in Ion Transport in Block Copolymer Electrolytes

Ion conducting block copolymers can overcome traditional limitations of homopolymer electrolytes by phase separating into nanoarchitectures that can be simultaneously optimized for two or more orthogonal material properties such as high ionic conductivity and mechanical stability. A key challenge in understanding the ion transport properties of these materials is the difficulty of extracting structure-function relationships without having complete knowledge of all nanoscale transport pathways in bulk samples. Here we demonstrate a method for deriving structure-transport relationships for ion conducting block copolymers using thin films and interdigitated electrodes. Well-defined and directly imaged structure in films of poly(styrene)-block-poly(2-vinylpyridine) is controlled using techniques of directed self-assembly then the poly(2-vinylpyridine) is selectively converted into an ion conductor. The ion conductivity is found to be directly proportional to the total number of connected paths between electrodes and the path length. A single defect such as a dislocation anywhere in the path of an ion conducting route disconnects and precludes that pathway from contributing to the conductivity and results in an increase in the dielectric parameter of the film. When all the ion conduction pathways are blocked between electrodes, the conductivity is negligible, 4 orders of magnitude lower compared to a completely connected morphology and the dielectric parameter increases by a factor of 50. These results have profound implications for the interpretation, design, and processing of block copolymer electrolytes for applications as ion conducting membranes.

POISED-5, a portable on-board electrochemical impedance spectroscopy biomarker analysis device

Point-of-care medical devices offer the potential for rapid biomarker detection and reporting of medical conditions, thereby bypassing the requirements for offline clinical laboratory facilities in many cases. Label-free electrochemical techniques are suitable for use in handheld diagnostic devices due the inherent electronic detection modality and low requirement for processing reagents. While electrochemical impedance sensing is widely used in tissue analysis such as body composition measurement, its use in point-of-care patient testing is yet to be widely adopted. Here we have considered a number of issues currently limiting the translation of electrochemical impedance sensing into clinical biosensor devices. Specifically, we have addressed the current requirement for these sensors to be connected to an external processor by applying a minimum number of frequencies required for optimized biomarker detection, and subsequently delivering analytics within the measurement device. The POISED-5 device was evaluated using a sensor for the ovarian cancer biomarker cancer antigen 125 (CA125), demonstrating performance comparable to standard laboratory equipment, with direct interpretation of response signal amplitude substituting traditional impedance component calculation and model fitting.

Electrochemiluminescence-Based Capacitance Microscopy for Label-Free Imaging of Antigens on the Cellular Plasma Membrane

Electrochemiluminescence (ECL)-based capacitance microscopy using a square-wave voltage is established unprecedentedly to realize the label-free visualization of species on electrode surfaces and cellular plasma membranes. The drop in the local capacitance upon the binding of species to the surface or to a cellular membrane is derived to induce a relatively larger potential drop ( V_dl) across the double layer on the local electrode surface, which is utilized to prompt enhanced ECL at the binding position. The square-wave voltage with a frequency of as high as 1.5 kHz is proven to be favorable for the discrimination of the local ECL from the surrounding signal. Using this new detection principle and resultant capacitance microscopy, carcinoembryonic antigens (CEA) at amounts of as low as 1 pg can be visualized. Further application of this approach permits the direct imaging of CEA antigens on single MCF-7 cells through the capacitance change after the formation of the antigen-antibody complex. Successful visualization of the analyte without any ECL tag will allow not only special capacitance microscopy for label-free bioassays but also a novel ECL detection approach for the sensitive detection of biomolecules.

Research advances in the detection of miRNA

MicroRNAs (miRNAs) are a family of endogenous, small (approximately 22 nucleotides in length), noncoding, functional RNAs. With the development of molecular biology, the research of miRNA biological function has attracted significant interest, as abnormal miRNA expression is identified to contribute to serious human diseases such as cancers. Traditional methods for miRNA detection do not meet current demands. In particular, nanomaterial-based methods, nucleic acid amplification-based methods such as rolling circle amplification (RCA), loop-mediated isothermal amplification (LAMP), strand-displacement amplification (SDA) and some enzyme-free amplifications have been employed widely for the highly sensitive detection of miRNA. MiRNA functional research and clinical diagnostics have been accelerated by these new techniques. Herein, we summarize and discuss the recent progress in the development of miRNA detection methods and new applications. This review will provide guidelines for the development of follow-up miRNA detection methods with high sensitivity and specificity, and applicability to disease diagnosis and therapy.

Rapid electrochemical device for single-drop point-of-use screening of parathyroid hormone

Aim: Novel electrochemical point-of-use biosensing device for rapid assessment of parathyroid hormone (PTH) levels has been developed. Materials & methods: The analytical nanobiosensor was designed by integrating unique high density semiconducting nanostructured arrays on a flexible sensing surface. Surface modification technique was tailored for enhancing the interaction of nanostructure–biological interface to capture the target PTH level. Results & conclusion: We demonstrate a rapid nanobiosensor to detect PTH in human serum, plasma and whole blood with a limit of detection of 1 pg/ml and a clinically relevant dynamic range from 1 to 1000 pg/ml. This is the first demonstration of detecting PTH as a point-of-use device devoid of sample pretreatment suitable in a surgical setting with high specificity to PTH.

Physical Structure and Electrochemical Response of Diamond-Graphite Nanoplatelets: From CVD Synthesis to Label-Free Biosensors

Hybrid diamond-graphite nanoplatelet (DGNP) thin films are produced and applied to label-free impedimetric biosensors for the first time, using avidin detection as a proof of concept. The DGNPs are synthesized by microwave plasma chemical vapor deposition through H₂/CH₄/N₂ gas mixtures in a reproducible and rapid single-step process. The material building unit consists of an inner two-dimensional-like nanodiamond with preferential vertical alignment covered by and covalently bound to nanocrystalline graphite grains, exhibiting {111}_diamond||{0002}_graphite epitaxy. The DGNP films' morphostructural aspects are of interest for electrochemical transduction, in general, and for Faradaic impedimetric biosensors, in particular, combining enhanced surface area for biorecognition element loading and facile Faradaic charge transfer. Charge transfer rate constants in phosphate buffer saline/[Fe(CN)₆]^4- solution are shown to increase up to 5.6 × 10^-3 cm s^-1 upon N₂ addition to DGNP synthesis. For the impedimetric detection of avidin, biotin molecules are covalently bound as avidin specific recognition elements on (3-aminopropyl)triethoxysilane-functionalized DGNP surfaces. Avidin quantification is attained within the 10-1000 μg mL^-1 range following a logarithmic dependency. The limits of detection and of quantitation are 1.3 and 6.4 μg mL^-1 (19 and 93 nM), respectively, and 2.3 and 13.8 μg mL^-1 (33 and 200 nM) when considering the nonspecific response of the sensors.

Temporary Inhibition of the Corrosion of AZ31B Magnesium Alloy by Formation of Bacillus subtilis Biofilm in Artificial Seawater

It is well known that microorganisms tend to form biofilms on metal surfaces to accelerate/decelerate corrosion and affect their service life. Bacillus subtilis was used to produce a dense biofilm on an AZ31B magnesium alloy surface. Corrosion behavior of the alloy with the B. subtilis biofilm was evaluated in artificial seawater. The results revealed that the biofilm hampered extracellular electron transfer significantly, which resulted in a decrease of i_corr and increase of R_t clearly compared to the control group. Moreover, an ennoblement of E_corr was detected under the condition of B. subtilis biofilm covering. Significant reduction of the corrosion was observed by using the cyclic polarization method. All of these prove that the existence of the B. subtilis biofilm effectively enhances the anti-corrosion performance of the AZ31B magnesium alloy. This result may enhance the usage of bio-interfaces for temporary corrosion control. In addition, a possible corrosion inhibition mechanism of B. subtilis on AZ31B magnesium alloy was proposed.

Coupling Self-Assembly Mechanisms to Fabricate Molecularly and Electrically Responsive Films

Biomacromolecules often possess information to self-assemble through low energy competing interactions which can make self-assembly responsive to environmental cues and can also confer dynamic properties. Here, we coupled self-assembling systems to create biofunctional multilayer films that can be cued to disassemble through either molecular or electrical signals. To create functional multilayers, we: (i) electrodeposited the pH-responsive self-assembling aminopolysaccharide chitosan, (ii) allowed the lectin Concanavalin A (ConA) to bind to the chitosan-coated electrode (presumably through electrostatic interactions), (iii) performed layer-by-layer self-assembly by sequential contacting with glycogen and ConA, and (iv) conferred biological (i.e., enzymatic) function by assembling glycoprotein (i.e., enzymes) to the ConA-terminated multilayer. Because the ConA tetramer dissociates at low pH, this multilayer can be triggered to disassemble by acidification. We demonstrate two approaches to induce acidification: (i) glucose oxidase can induce multilayer disassembly in response to molecular cues, and (ii) anodic reactions can induce multilayer disassembly in response to electrical cues.

Characterization of semiconductor photocatalysts

The long-standing popularity of semiconductor photocatalysts stimulated their characterization, which is the subject of this review aiming to help materials chemists and physicists, particularly students, to select suitable characterization methods.