Degradation and removal methods of antibiotics from aqueous matrices--a review

Cellulose nanocrystals/graphene oxide composite for the adsorption and removal of levofloxacin hydrochloride antibiotic from aqueous solution

Residual antibiotics in water are often persistent organic pollutants. The purpose of this study was to prepare a cellulose nanocrystals/graphene oxide composite (CNCs-GO) with a three-dimensional structure for the removal of the antibiotic levofloxacin hydrochloride (Levo-HCl) in water by adsorption. The scanning electron microscope, Fourier transform infrared (FT-IR), energy-dispersive spectroscopy, X-ray photoelectron spectroscopy and other characterization methods were used to study the physical structure and chemical properties of the CNCs-GO. The three-dimensional structure of the composite material rendered a high surface area and electrostatic attraction, resulting in increased adsorption capacity of the CNCs-GO for Levo-HCl. Based on the Box-Behnken design, the effects of different factors on the removal of Levo-HCl by the CNCs-GO were explored. The composite material exhibited good antibiotic adsorption capacity, with a removal percentage exceeding 80.1% at an optimal pH of 4, the adsorbent dosage of 1.0 g l^-1, initial pollutant concentration of 10.0 mg l^-1 and contact time of 4 h. The adsorption isotherm was well fitted by the Sips model, and kinetics studies demonstrated that the adsorption process conformed to a quasi-second-order kinetics model. Consequently, the as-synthesized CNCs-GO demonstrates good potential for the effective removal of antibiotics such as levofloxacin hydrochloride from aqueous media.

Green preparation of activated carbon from pomegranate peel coated with zero-valent iron nanoparticles (nZVI) and isotherm and kinetic studies of amoxicillin removal in water

In present research, the activated carbon was prepared by a green approach from pomegranate peel coated with zero-valent iron nanoparticles (AC-nZVI) and developed as adsorbent for the removal of amoxicillin from aqueous solution. The physicochemical properties of the AC-nZVI were investigated using XRD, FTIR, and FESEM techniques. The optimal values of the parameters for the best efficiency (97.9%) were amoxicillin concentration of 10 mg/L, adsorbent dose of 1.5 g/L, time of 30 min, and pH of 5, respectively. The adsorption equilibrium and kinetic data were fitted with the Langmuir monolayer isotherm model (qmax 40.282 mg/g, R² 0. 0.999) and pseudo-first order kinetics (R² 0.961). The reusability of the adsorbent also revealed that the adsorption efficiency decreased from 83.54 to 50.79% after five consecutive repetitions. Overall, taking into account the excellent efficiency, availability, environmental friendliness, and good regeneration, AC-nZVI can be introduced as a promising absorbent for amoxicillin from aquatic environments.

Nanoparticle-templated conversion of glucose to a high surface area biocarbon for the removal of organic pollutants in water

While extensive work has been done on the generation of adsorbents by carbonization of large polymeric structures, few works are currently available for the use of monomeric carbon molecules as precursors during carbonization. In this work we report the formation of a carbon adsorbent material from the carbonization of glucose in the presence of zinc oxide (ZnO) nanoparticle templates. Carbonization at 1,000 °C under inert atmosphere yields a product with Brunauer-Emmett-Teller (BET) surface area of 1,228.19 m²/g and 14.77 nm average pore diameter. Adsorption capacities against methylene blue, 2-naphthol and bisphenol-A at pH 7 were found to be 539 mg/g, 737 mg/g and 563 mg/g, respectively. Our material demonstrates a strong fit with the Langmuir isotherm, and adsorption kinetics show regression values near unity for the pseudo-second order kinetic model. A flow adsorption column was implemented for the remediation of tap water containing 20 mg/L methylene blue and found to quantitatively purify 11.5 L of contaminated water.

Evolution of antibiotic resistance at low antibiotic concentrations including selection below the minimal selective concentration

Determining the selective potential of antibiotics at environmental concentrations is critical for designing effective strategies to limit selection for antibiotic resistance. This study determined the minimal selective concentrations (MSCs) for macrolide and fluoroquinolone antibiotics included on the European Commissionʼs Water Framework Directive’s priority hazardous substances Watch List. The macrolides demonstrated positive selection for ermF at concentrations 1–2 orders of magnitude greater (>500 and <750 µg/L) than measured environmental concentrations (MECs). Ciprofloxacin illustrated positive selection for intI1 at concentrations similar to current MECs (>7.8 and <15.6 µg/L). This highlights the need for compound specific assessment of selective potential. In addition, a sub-MSC selective window defined by the minimal increased persistence concentration (MIPC) is described. Differential rates of negative selection (or persistence) were associated with elevated prevalence relative to the no antibiotic control below the MSC. This increased persistence leads to opportunities for further selection over time and risk of human exposure and environmental transmission.

Stanton et al. determine the minimal selective concentrations for macrolide and fluoroquinolone antibiotics and describe a selective window defined by the minimal increased persistence concentration. These assessments and thresholds allow for better assessment of potential selection for antibiotic resistance and the risks of human exposure and environmental transmission.

Characterization of activated bentonite clay mineral and the mechanisms underlying its sorption for ciprofloxacin from aqueous solution

The presence of emerging pollutants such as hazardous chemicals, pharmaceuticals, pesticides, and endocrine-disrupting chemicals in water sources is a serious concern to the environment and human health. Thus, this study focused on exploring the interaction mechanisms between ciprofloxacin (CIP) (antibiotic) and clay (a low-cost adsorbent) during sorption process. Acid activation technique was opted for modifying natural bentonite (NB) to enhance the adsorptive removal of CIP from water. The BET surface area analysis revealed that acid-activated bentonite (AAB) possessed more than two fold higher surface area as compared to NB. Combining pH_zpc measurements, effect of solution pH and CIP speciation revealed that CIP sorption onto bentonite is highly dependent on solution pH. Kinetic studies confirmed that CIP sorption mechanism was chemisorption which included ion-exchange and surface complexation mechanisms. The mechanism of CIP sorption onto AAB was successfully explored with the assistance of characterization techniques. Maximal monolayer sorption capacity of AAB was found to be 305.20 mg/g, compared to 126.56 mg/g for NB. Reusability studies demonstrated that AAB could be reused successfully up to 5 cycles. Furthermore, column studies showed satisfactory results confirming that AAB can be successfully used in continuous mode for practical applications.

Performance of microbial fuel cell for treating swine wastewater containing sulfonamide antibiotics

The proper treatment of swine wastewater with relatively high concentrations of antibiotics is very important to protect environmental safety and human health. Microbial fuel cell (MFC) technology shows much promise for removing pollutants and producing electricity simultaneously. A double-chamber MFC was investigated in this study. Synthetic swine wastewater with the addition of sulfonamides was used as the fuels in the anode chamber. Results indicated that COD could be effectively removed (>95%) and virtually not affect by the presence of sulfonamides in the MFC. A stable voltage output was also observed. The removal efficiencies of sulfamethoxazole (SMX), sulfadiazine (SDZ), and sulfamethazine (SMZ) in the MFC were in the 99.46-99.53%, 13.39-66.91% and 32.84-67.21% ranges, respectively. These totals were higher than those reported for a traditional anaerobic reactor. Hence, MFC revealed strong resistance to antibiotic toxicity and high potential to treat swine wastewater with antibiotics.

Isolation and characterization of a marine bacterium Vibrio diabolicus strain L2-2 capable of biotransforming sulfonamides

Sulfonamides (SAs) have attracted much attention because of their high detection rates in natural water. In this study, a marine bacterium Vibrio diabolicus strain L2-2 was isolated which could metabolize 9 SAs to a different extent. Compared with SAs and their analogs, SAs with N-oxides of heterocyclic structure were easier to be transformed to their N⁴-acetylated metabolites or their isoxazole ring rearrangement isomers by strain L2-2. And, gene vdnatA and vdnatG were likely to be the key genes in SAs acetylation process, which might code Arylamine N-acetyltransferase. The biotransformation rates of sulfathiazole(STZ), sulfamonomethoxine(SMT), sulfadiazine(SDZ), sulfamethoxazole(SMX) and sulfisoxazole(SIX) could reach 29.39 ± 5.63, 24.97 ± 4.45, 79.41 ± 4.05, 64.64 ± 1.71, 32.82 ± 4.46% in 6 days, respectively. Besides, the overall optimal conditions for SAs biotransformation were less than 100 mg/L for total SAs in neutral or weakly alkaline medium with the salinity of 10-20‰ and additional nutrients like glucose, sucrose or glycerine. Furthermore, toxicity was demonstrated to be significantly reduced after biotransformation. Together, this study introduced a strategy to use V. diabolicus strain L2-2 to realize simultaneous removal and detoxification of multiple SAs in freshwater and seawater, and revealed SAs removal pathways and relevant molecular mechanism.

Mechanism analysis for the process-dependent driven mode of NaHCO3 in algal antibiotic removal: efficiency, degradation pathway and metabolic response

This work provided a comprehensive perspective to investigate the performance of NaHCO₃-driving effect and mechanism including the antibiotic removal, degradation pathway and metabolites analysis, and the algal physiological response during the removal process. Cefuroxime sodium was selected as the target antibiotic. Our results showed that NaHCO₃ did not facilitate self-decomposition of the target antibiotic, while drove the improvement on the removal capacity of every algal cell, which then attributed to the total removal efficiency. After 24 h, there was an improvement on the removal rate of the target antibiotic (from 10.21% to 92.89%) when NaHCO₃ was added. The degradation pathway of the target antibiotic was confirmed by the formation of three main products (M1, M2 and M3), and the degradation process, that from M1 to M2 and M2 to M3, was accelerated by the existence of NaHCO₃. Besides, a 4-stage model illustrated the relationship between NaHCO₃ and antibiotic removal process. Moreover, algal culture that supplemented with NaHCO₃ demonstrated a better growth capacity. A large increase in the content of chlorophyll a and a moderate increase in the activity of two carbon metabolic enzymes (RuBisCO and CA) might be viewed as a positive response of the algae during the NaHCO₃-driving process.

Elemental red phosphorus-based materials for photocatalytic water purification and hydrogen production

Semiconductor-based photocatalysis is a renewable and sustainable technology to solve global environmental pollution and energy shortage problems. It is essential to exploit highly efficient photocatalyst materials. Recently, Earth-abundant elemental red phosphorus (RP) with broader light-harvesting and appropriate band structure characteristics has been widely studied in photocatalysis. In this review, the crystal and electronic structures of RP (e.g., amorphous, Hittorf's and fibrous phosphorus) materials are firstly summarized along with the current advancement in the synthesis strategies of RP and RP-based materials in photocatalysis accompanied by a thorough discussion of the applications of RP-based materials in photocatalytic pollutant degradation, bacterial inactivation, and water splitting. Finally, this review also offers some guidance and perspectives for the future design of efficient visible-light-driven photocatalysts.

Nanocomposite material from TiO2 and activated carbon for the removal of pharmaceutical product sulfamethazine by combined adsorption/photocatalysis in aqueous media

This work was dedicated to the elaboration of new composite materials based on activated carbon and titanium oxide as an ecological solution for the cleaning of water contaminated with pharmaceutical pollutants. Such new composite materials allowed the combining of adsorption and photocatalytic process, which allows a cleaning process that is low cost making them promising materials. The functionalization of the surface of activated carbon (AC) by TiO₂ nanoparticles forms the core of the nanocomposite material. This was accomplished using sol-gel process with molar ratios R_n (n_Ti/n_AC) in the range of 1/10 to 7/10 followed by a calcination step (400 °C, N₂, 2 h). Using various characterization techniques, AC surface functionalization was confirmed and the formation of a TiO₂ coating on the AC was noticed with TiO₂ under its unique anatase crystallographic form. The study of adsorption and photocatalytic degradation of the sulfamethazine antibiotic demonstrated that the most photoactive nanocomposite corresponds to the one with R_n = 0.5. Freundlich model was proved to be a perfect fit with the experimental results stating that the adsorption is of multilayer nature on the surface of the adsorbent and with interactions between the pollutants adsorbed on its surface. The photocatalytic degradation of the remaining pharmaceutical pollutant in the solution was evidenced and essentially occurred through the involvement of hydroxyl radicals formed by the excitation of the photocatalyst. The formation of the photoproducts analyzed by the LC/MS technique implies the splitting of the sulfonamide bridge, and by the hydroxylation of the aromatic ring and the pyrimidine group.

Tetracycline Photocatalytic Degradation under CdS Treatment

Industrialization and the growing consumption of medicines leads to global aquatic contamination. One of the antibiotics widely used against bacterial infections in both human and veterinary medicine is tetracycline. Despite its positive antibiotic action, tetracycline is resistant against degradation, and therefore it accumulates in the environment, including the aquatic environment, creating great health hazards, possibly stimulating antibiotic resistance of pathogenic organisms. In this research, aqueous suspensions of semiconductor nanoparticles CdS were used for photocatalytic activity studies in the presence of methylene blue as a model compound, and finally, in the presence of tetracycline, a broad-spectrum antibiotic widely used against bacterial infections, as well as a live-stock food additive. The mechanism and kinetic rate constants of photocatalytic degradation processes of methylene blue and tetracycline were described in correlation with the energy diagram of CdS nanoparticles.

Heterogeneous photocatalysis in flow chemical reactors

The synergy between photocatalysis and continuous flow chemical reactors has shifted the paradigms of photochemistry, opening new avenues of research with safer and scalable processes that can be readily implemented in academia and industry. Current state-of-the-art photocatalysts are homogeneous transition metal complexes that have favourable photophysical properties, wide electrochemical redox potentials, and photostability. However, these photocatalysts present serious drawbacks, such as toxicity, limited availability, and the overall cost of rare transition metal elements. This reduces their long-term viability, especially at an industrial scale. Heterogeneous photocatalysts (HPCats) are an attractive alternative, as the requirement for the separation and purification is largely removed, but typically at the cost of efficiency. Flow chemical reactors can, to a large extent, mitigate the loss in efficiency through reactor designs that enhance mass transport and irradiation. Herein, we review some important developments of heterogeneous photocatalytic materials and their application in flow reactors for sustainable organic synthesis. Further, the application of continuous flow heterogeneous photocatalysis in environmental remediation is briefly discussed to present some interesting reactor designs that could be implemented to enhance organic synthesis.

UV photolysis as an efficient pretreatment method for antibiotics decomposition and their antibacterial activity elimination

The biological treatment of antibiotic-containing wastewater is a mainstream process, but the antibacterial activity from the persistence of antibiotics would inhibit the biological activity and function of wastewater treatment plants and lead to the risk of transmission of antibiotic resistant bacteria and genes. In this study, UV photolysis was selected as an appropriate pretreatment technology for antibiotic-containing wastewater. It could decompose many kinds of antibiotics and was not inhibited by the coexisting organics in wastewater. The antibacterial activities of five kinds of antibiotics, which were eliminated with UV irradiation, exhibited a significantly positive correlation with their parent compound concentrations. The photodecomposition of the main functional groups in antibiotics contributed to the elimination of antibacterial activity. Defluorination was the main pathway to eliminate the antibacterial activity of antibiotics containing a fluorine substituent (e.g., florfenicol and ofloxacin), while the photoinduced opening of the β-lactam ring was the most efficient route to eliminate the antibacterial activity of β-lactam antibiotics (e.g. cefalexin, amoxicillin and ampicillin). These results demonstrated that UV photolysis could be adopted as an efficient and promising pretreatment strategy for the source control of antibiotic antibacterial activity by the decomposition of antibiotic functional groups before the biological treatment unit.

Synthesis of Novel 1T/2H-MoS2 from MoO3 Nanowires with Enhanced Photocatalytic Performance

Metallic 1T-phase MoS₂ is a newly emerging and attractive catalyst since it has more available active sites and high carrier mobility in comparison with its widely used counterpart of semiconducting 2H-MoS₂. Herein, 1T/2H-MoS₂(N) (N: MoO₃ nanowires were used to prepare 1T/2H-MoS₂) was synthesized by using molybdenum trioxide (MoO₃) nanowires as the starting material and applied in the photodegradation of antibiotic residue in water. Enhanced photocatalytic performance was observed on the obtained 1T/2H-MoS₂(N), which was 2.8 and 1.3 times higher than those on 1T/2H-MoS₂(P) (P: commercial MoO₃ powder was used to prepare 1T/2H-MoS₂) and 2H-MoS₂, respectively. The active component responsible for the photodegradation was detected and a reaction mechanism is proposed.

N, S-Doped porous carbons for persulfate activation to remove tetracycline: Nonradical mechanism

Nitrogen and sulfur-codoped porous carbons (SNCs) with porous structures and high surface areas were successfully synthesized employing coffee grounds, sodium bicarbonate and L-cysteine monohydrochloride as precursors. The SNCs were highly efficient for adsorption and exhibited outstanding catalytic performance for the oxidative degradation of tetracycline hydrochloride (TeC) solutions, especially at a calcined temperature of 700 °C (SNCs-700). The radical quenching, advanced in situ electron paramagnetic resonance (EPR) technology, PS decomposition rates and Linear Sweep Voltammetry (LSV) indicated that the excellent oxidative effectiveness of the PS/SNCs-700 system originated from the nonradical pathways (singlet oxygen (¹O₂) and electron transfer). It's supposed that N and S doping can effectively create point defects, which could generate ¹O₂, while carbonyl groups were determined to be the main active sites contributing to the electron transfer. TeC degradation intermediates were also identified, three degradation pathways, revealing that the pre-adsorption significantly accelerated the nonradical oxidation pathways. This approach provides an innovative method for the large-scale production and application of high-quality catalysts in water treatment.

Photocatalytic degradation of penicillin G from simulated wastewater using the UV/ZnO process: isotherm and kinetic study

PURPOSE

Pharmaceutical contaminants, including antibiotics, present in the environment, especially water resources, are a main concern for human and environmental health due to their stability and non-degradability. Accordingly, the purpose of this study was to investigate the photocatalytic removal of penicillin G antibiotic from simulated wastewater using a photocatalytic process [UV/ZnO] in an isotherm and kinetic study.

METHODS

In the current research, the ZnO nanoparticles [ZnO NPs] were initially characterized by scanning electron microscope [SEM] and X-ray diffraction [XRD]. Then, its efficiency was investigated in the photocatalytic degradation process of penicillin G. The evaluated parameters in the adsorption process penicillin G antibiotic were pH [1-5], penicillin G concentration [10-30 mgL-1], NP dosage [0.5-4.5 gL-1] and contact time [5 to 200 min]. Then, the effect of pH [3, 5, 7, 9, 11, and], penicillin G concentration [10-30 mgL-1], NP dosage [0.01-1.5 gL-1] and contact time [5 to 200 min] in the photocatalytic degradation (UV/ZnO) was studied. The residual penicillin G concentration was measured using a spectrophotometery at a wavelength of 283 nm.

RESULTS

The results indicated that the penicillin G removal efficiency of photocatalytic process [UV/ZnO] using ZnO was 74.65% at the concentration of 10 mgL-1, the pH value of 5, the ZnO NP dosage of 0.1 gL-1 and the contact time of 180 min, as well as the kinetics of degradation followed the pseudo-first-order kinetic model.

CONCLUSION

It can be concluded that the use of this process is appropriate an effective for the removal of the antibiotic pollutants.

Modified Activated Carbon Fiber Felt for the Electrosorption of Norfloxacin in Aqueous Solution

As an antibiotic, Norfloxacin (NOR) is widely found in the water environment and presents considerable harm to human beings. At present, the preparation of removal materials is complicated, and the removal efficiency is not high. The adsorption effect of modified activated carbon fiber felt (MACFF) electrosorption and its influencing factors on NOR were studied. Activated carbon fiber felt (ACFF) was modified with 20% nitric acid, and the ACFFs were characterized by SEM, TEM, and FTIR both before and after modification. The optimal working conditions for electrosorption with an MACFF electrode were as follows: the voltage was 1.0 V, the pH was 6, and the plate spacing was 10 mm. The maximum adsorption capacity of the MACFF for NOR was 128.55 mg/g. Model fitting showed that pseudo-second-order kinetic model and Langmuir model were more suitable for explaining this adsorption process. In addition, this study found that, with 20% nitric acid as the regeneration liquid and under the reverse charging method, the regeneration rate of the MACFF electrode was maintained at approximately 96% and the regeneration was good, therefore, this technology can not only save operation costs but also has good development prospects in sewage treatment.

Enhancement of ionizing radiation-induced catalytic degradation of antibiotics using Fe/C nanomaterials derived from Fe-based MOFs

In present work, we studied a novel Fe/C nanomaterial fabricated using Fe-based metal organic frameworks (MOFs) as precursors through thermal pyrolysis to catalyze gamma irradiation-induced degradation of antibiotics, cephalosporin C (CEP-C) and sulfamethazine (SMT) in aqueous solution. The MOFs-derived Fe/C nanomaterials (DMOFs) had the regular octahedrons structure of MOFs and contained element C, Fe and O, while Fe° with a fraction of Fe₃O₄ and Fe₂O₃ were identified. Results showed that DMOFs addition could accelerate the generation of OH during gamma irradiation, while the intermediates of bonds cleavages of antibiotic molecules and OH addition were identified. DMOFs were more effective to improve the decomposition of antibiotic having the higher adsorption capacity like SMT. The degradation rate of CEP-C and SMT increased by 1.3 times and 1.8 times, and TOC reduction at 1.0 kGy reached 42 % and 51 %, respectively by gamma/DMOFs treatment, while only 20.2 % (CEP-C) and 4.5 % (SMT) of TOC reduction were obtained by γ-irradiation alone. The crystal structure, functional groups and magnetism of DMOFs changed slightly after gamma irradiation, which made it possible to be reused. DMOFs were promising to enhance the degradation of antibiotics during gamma irradiation.

Simultaneous removal and high tolerance of norfloxacin with electricity generation in microbial fuel cell and its antibiotic resistance genes quantification

Norfloxacin (NFLX) is a synthetic antibiotic widely used in the treatment of infectious diseases. In this work, the performance of microbial fuel cells (MFCs) toward NFLX degradation, electricity production and the antibiotics resistances genes (ARGs) generation was investigated. NFLX degradation efficiency and COD removal reached 65.5% and 94.5% respectively. The increase in NFLX concentration (128 mg/L) had no significant influence on NFLX degradation efficiency, COD removal and MFCs voltage output while the electricity was successfully generated. The quantitative polymerase chain reaction (qPCR) indicated low absolute abundances of ARGs (mdtk, mdtm, and pmra) compared with the traditional wastewater treatment plants (WWTPs). Anodic bacteria can survive in the presence of high NFLX concentration and sustain its degradation and electricity production. In terms of NFLX degradation, COD removal, diminished ARGs generation and simultaneous energy production, MFC seems to be a promising technology for antibiotics wastewater treatment with a potential to overcome the ARGs challenge.

Degradation of the emerging concern pollutant ampicillin in aqueous media by sonochemical advanced oxidation processes - Parameters effect, removal of antimicrobial activity and pollutant treatment in hydrolyzed urine

This work presents the degradation of ampicillin (a highly consumed β-lactam antibiotic) in aqueous media by sonochemical advanced oxidation processes. Initially, effects of frequency, power and operation mode (continuous vs. pulsed) on the antibiotic degradation by sonochemistry were analyzed. Then, under the suitable operational conditions, pollutant degradation and antimicrobial activity (AA) evolution were monitored. Afterwards, computational calculations were done to establish the possible attacks by the hydroxyl radical to the ampicillin structure. Additionally, the antibiotic degradation in synthetic hydrolyzed urine by ultrasound was performed. Finally, the combination of sonochemistry with Fenton (sono-Fenton) and photo-Fenton (sono-photo-Fenton) was evaluated. Our research showed that ampicillin removal was favored at low frequency, high power (i.e., 375 kHz, 24.4 W) and continuous mode (exhibiting an initial degradation rate of 0.78 μM min^-1). Interestingly, ampicillin degradation in the hydrolyzed urine by sonochemistry alone was favored by matrix components (i.e., the pollutant showed a degradation rate in urine higher than in distilled water). The sonochemical process decreased the antimicrobial activity from the treated water (100% removal after 75 min of treatment), which was related to attacks of hydroxyl radical on active nucleus (the computational analysis showed high electron density on sulfur, oxygen and carbon atoms belonging to the penicillin core). Sono-photo-Fenton system achieved the fastest degradation and highest mineralization of the pollutant (40% of organic carbon removal at 180 min of treatment). All these aspects reveal the good possibility of sonochemical advanced oxidation technologies application for the treatment of antibiotics even in complex aqueous matrices such as hydrolyzed urine.

Ozonation Pretreatment for Reduction of Landfill Leachate Fouling on Membranes: A Response Surface Methodology Analysis

Batch ozonation was performed to assess its efficacy as a pretreatment for reverse osmosis (RO) membranes for treating leachate with high concentrations of recalcitrant organic compounds. Leachate samples from two different landfills were collected and characterized. The modified fouling index (MFI) was used to estimate the fouling potential of raw and ozonized leachates. A response surface experimental design was applied to optimize operational pH and ozone dose. The results demonstrate that the best operational conditions are 1.5 g/L of O3 at pH 12.0 and 1.5 g/L of O3 at pH 9.0 for Landfills 1 and 2, which reduce MFI by 96.22% and 94.08%, respectively. Additionally, they show toxicity factor decays of 98.44% for Landfill 1 and 93.75% for Landfill 2. These results, along with the similar behavior shown by leachate samples from distinct landfills, suggest that ozonation is a promising technology to fit this kind of wastewater into the requirements of RO membranes, enabling their use in such treatment.

Current Trends in the Application of Nanomaterials for the Removal of Emerging Micropollutants and Pathogens from Water

Water resources contamination has a worldwide impact and is a cause of global concern. The need for provision of clean water is becoming more and more demanding. Nanotechnology may support effective strategies for the treatment, use and reuse of water and the development of next-generation water supply systems. The excellent properties and effectiveness of nanomaterials make them particularly suitable for water/wastewater treatment. This review provides a comprehensive overview of the main categories of nanomaterials used in catalytic processes (carbon nanotubes/graphitic carbon nitride (CNT/g-C₃N₄) composites/graphene-based composites, metal oxides and composites, metal–organic framework and commercially available nanomaterials). These materials have found application in the removal of different categories of pollutants, including pharmaceutically active compounds, personal care products, organic micropollutants, as well as for the disinfection of bacterial, viral and protozoa microbial targets, in water and wastewater matrices. Apart from reviewing the characteristics and efficacy of the aforementioned nanoengineered materials for the removal of different pollutants, we have also recorded performance limitations issues (e.g., toxicity, operating conditions and reuse) for their practical application in water and wastewater treatment on large scale. Research efforts and continuous production are expected to support the development of eco-friendly, economic and efficient nanomaterials for real life applications in the near future.

Determination of Bisphenol A by High-Performance Liquid Chromatography Based on Graphene Magnetic Dispersion Solid Phase Extraction

Bisphenol A (BPA), as one of the environmental endocrine disruptors, is extensively existing and threatening to human health. To evaluate the environmental exposure level and protect human from the hazard of BPA, a precise and sensitive method is established. In this work, Graphene@ Fe3O4 (G@Fe3O4) is prepared by chemical coprecipitation method as magnetic dispersion solid phase extraction (MDSPE) material. The rapid and specific detection method of BPA is carried out by high-performance liquid chromatography (HPLC). Properties of G@Fe3O4 are identified by the fourier infrared spectrum and scanning electron microscopy. Conditions of solid phase extraction are optimized. Under the optimal extraction conditions, G@Fe3O4 has perfect enrichment effect on BPA. There is a good linear relationship in the range of 5.0~1000.0 μg/L with the correlation coefficient of 0.9997. The detection limit is 0.1 μg/L. This method is applied to water samples successfully, and recoveries of BPA are between 88.19% and 99.56% (RSDs < 3.00%). G@Fe3O4 was synthesized, which was used to extract BPA in water samples before HPLC analysis, and has shown perfect extraction ability toward BPA, which indicates that the determination method of BPA by HPLC based on graphene MDSPE is faster and more precise.

Unravelling the menace: detection of antimicrobial resistance in aquaculture

One of the major problems to be addressed in aquaculture is the prominence of antimicrobial resistance (AMR). The occurrence of bacterial infections in cultured fishes promotes the continuous use of antibiotics in aquaculture, which results in the selection of proliferated antibiotic-resistant bacteria and increases the possibility of transfer to the whole environment through horizontal gene transfer. Hence, the accurate cultivation-dependent and cultivation-independent detection methods are very much crucial for the immediate and proper management of this menace. Antimicrobial resistance determinants carrying mobile genetic transfer elements such as transposons, plasmids, integrons and gene cassettes need to be specifically analysed through molecular detection techniques. The susceptibility of microbes to antibiotics should be tested at regular intervals along with various biochemical assays and conjugation studies so as to determine the extent of spread of AMR. Advanced omic-based and bioinformatic tools can also be incorporated for understanding of genetic diversity. The present review focuses on different detection methods to unearth the complexity of AMR in aquaculture. This monitoring helps the authorities to curb the use of antibiotics, commencement of appropriate management measures and adequate substitute strategies in aquaculture. The long battle of AMR could be overcome by the sincere implementation of One Health approach. SIGNIFICANCE AND IMPACT OF THE STUDY: The use of antibiotics and increased antimicrobial resistance (AMR) are of major concerns in aquaculture industry. This could result in global health risks through direct consumption of cultured fishes and dissemination of AMR to natural environment through horizontal gene transfer. Hence, timely detection of the antimicrobial-resistant pathogens and continuous monitoring programmes are inevitable. Advanced microbiological, molecular biological and omic-based tools can unravel the menace to a great extent. This will help the authorities to curb the use of antibiotics and implement appropriate management measures to overcome the threat.

Bio-inspired, high, and fast adsorption of tetracycline from aqueous media using Fe3O4-g-CN@PEI-β-CD nanocomposite: Modeling by response surface methodology (RSM), boosted regression tree (BRT), and general regression neural network (GRNN)

Because antibiotic-containing wastewaters are able to contaminate all environmental matrices (e.g. water bodies, soil, etc.), a special attention should be paid on developing appropriate materials for their remediation. Herein, the novel nanocomposite (NC) of Fe₃O₄-g-CN@PEI-β-CD was synthesized and employed effectively for the adsorptive removal of tetracycline (TC), the second most produced and employed antibiotic around the world. The successful fabrication of the nanocomposite with a high specific surface area (57.12 m²/g) was confirmed using XRD, SEM, TEM, FTIR, TGA, EDX, and BET analyses. The Fe₃O₄-g-CN@PEI-β-CD NC exhibited fast adsorption rates towards TC and maximum adsorption capacity on the basis of the Langmuir model reached 833.33 mg g^-1, much higher than that reported by different carbon- and/or nano-based materials. The adsorption process was modeled using the approaches of central composite design (CCD), boosted regression tree (BRT), and general regression neural network (GRNN) under various operational conditions of initial TC concentration, pH, adsorbent dose, tempreature, and time. The comparison of the models indicated good predictions of all, however, the BRT model was more accurate compared to the others, with R² = 0.9992, RMSE = 0.0026, MAE = 0.0014, and AAD = 0.0028, proving that it is a powerful approach for modeling TC adsorption by Fe₃O₄-g-CN@PEI-β-CD nanocomposite. The results showed that the order of the variables' effectiveness is as follow: pH > dose > TC concentration. The high adsorption capacity along with high efficiency (98 % in the optimized conditions by GA) ensures the potential of the as-prepared nanocomposite for in situ remediation of antibiotic-containing wastewaters.

A critical review on antibiotics and hormones in swine wastewater: Water pollution problems and control approaches

Swine wastewater (SW) is an important source of antibiotics and hormones (A&H) in the environment due to their large-scale application in swine industry. A&H in SW can be released into the water environment through the direct discharge of SW, effluent from SW treatment plants, and runoff and leaching from farmland polluted by swine wastes. The presence of A&H in the water environment has become an increasing global concern considering their adverse effects to the aquatic organism and human. This review critically discusses: (i) the occurrence of A&H in global water environment and their potential risks to water organisms and human; (ii) the management and technical approaches for reducing the emission of A&H in SW to the water environment. The development of antibiotic alternatives and the enhanced implementation of vaccination and biosecurity are promising management approaches to cut down the consumption of antibiotics during swine production. Through the comparison of different biological treatment technologies for removing A&H in SW, membrane-based bioprocesses have relatively higher and more stable removal efficiencies. Whereas, the combined system of bioprocesses and AOPs is expected to be a promising technology for elimination and mineralization of A&H in swine wastewater. Further study on this system is therefore necessary.

Effective Removal of Levofloxacin from Pharmaceutical Wastewater Using Synthesized Zinc Oxid, Graphen Oxid Nanoparticles Compared with their Combination

The presence of antibiotic traces in the aquatic system due to the inefficient treatment of the pharmaceutical wastewater represented threats, such as bioaccumulation and antibiotic-resistance, to the environment and human health. Accordingly, for the first time, the current work utilized the photocatalytic degradation and the adsorption approach for Levofloxacin (LEVO) in pharmaceutical wastewater using new designed nano aspects. Therefore, spherical Zinc oxide nanoparticles (ZnONP) sized 17 nm and ultrathin sheet-like structure graphene oxide nanosheets (GONS) with layer thickness ~5 nm were fabricated separately or in a combination between them then characterized via Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), X-Ray Diffraction (XRD), Fourier Transforms Infrared Spectroscopy (FTIR), absorption spectra (UV-Vis) and Brunauer-Emmett-Teller (BET). Additionally, several parameters were investigated to evaluate the potential of the removal process, such as pH, the exposure time to UV radiation, the type and concentration of the nanoparticles (NPs) and the initial concentration of the drug using a mixed fractional factorial design. The most effective parameter for LEVO removal was the NPs type followed by the initial drug concentration. Furthermore, an RP-HPLC/UV method was developed and validated for measuring the percentage of removal for LEVO drug. The highest percentage removal for both 50 and 400 µg mL⁻¹ LEVO was 99.2% and 99.6%, respectively, which was achieved using ZnONP/GONS combination at pH 9 ± 0.05 and UV light exposure time 120 min. In addition, the negative antibacterial activity of the treated wastewater sample confirmed the drug removal. The established protocol was successfully applied on wastewater samples collected from a pharmaceutical company that encouraged researchers to mainstream this design to be applied on other pharmaceutical wastewater drugs.

The removal of tetracycline, oxytetracycline, and chlortetracycline by manganese oxide-doped copper oxide: the behaviors and insights of Cu-Mn combination for enhancing antibiotics removal

Adsorption process is suitable to the advanced treatment of tetracycline antibiotics (TCs; including tetracycline (TTC), oxytetracycline (OTC), and chlortetracycline (CTC)) in poultry wastewater. In this research, Mn oxide-doped Cu oxide (MODCO) was synthesized and used for the removal of TTC, OTC, and CTC. According to the XRD and SEM analysis results, MODCO has an amorphous crystal structure and is formed by the aggregation of nano-sized particles with a uniform distribution of Cu and Mn elements. In addition, MODCO has a BET surface area of 67.7 m²/g and a pH_IEP value of 7.8. The results of batch experiments illustrated that the reaction rates for the removal of three TCs were in the order of OTC > CTC > TTC. In addition, the theoretical maximum amounts of TTC, OTC, and CTC adsorbed on MODCO were determined to be 2.90 mmol/g, 4.15 mmol/g, and 2.20 mmol/g via the Langmuir model, respectively. The optimal removal performances of TCs were achieved in the pH range of 6~9, and the coexistence of anions posed an unnoticeable effect on the removal efficiencies. The spectroscopic analysis results demonstrated that the removal mechanism of TCs was mainly attributed to surface complexation. Furthermore, a part of TCs may be decomposed by Mn oxides during the removal process according to the UV spectrogram results. Overall, MODCO has exhibited a great potential for the removal of TCs from aqueous solution.

Development of Novel Polymer Supported Nanocomposite GO/TiO2 Films, Based on poly(L-lactic acid) for Photocatalytic Applications

In the present study the development of novel polymer-supported nanocomposite graphene oxide (GO)–TiO2 films, based on poly(L-lactic acid), one of the most exploited bioplastics worldwide, was explored for photocatalytic applications. The nanocomposites were synthesized and evaluated as photocatalysts for the removal of a mixture of nine antibiotics, consisting of two sulphonamides (sulfamethoxazole, sulfadiazine), three fluoroquinolones (levofloxacin, norfloxacin, moxifloxacin), one anti-TB agent (isoniazid), one nitroimidazole (metronidazole), one lincosamide (lincomycin) and one diaminopyrimidine (trimethoprim), which are commonly found in wastewaters. The films were synthesized using 1 wt% GO and different TiO2 content (10, 25, and 50 wt%) and characterized using Fourier transform infrared spectroscopy (FTIR), wide-angle X-ray diffraction (WAXD), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Findings confirmed the successful immobilization of GO/TiO2 in all cases. The PLLA–GO–TiO2 50 wt% composite film demonstrated higher photocatalytic efficiency and, thus, was further investigated demonstrating excellent photostability and reusability even after four cycles. Overall, PLLA–GO–TiO2 50 wt% nanocomposite demonstrated high efficiency in the photocatalytic degradation of the antibiotics in various matrices including pure water and wastewater.

Removal of veterinary antibiotics from swine wastewater using anaerobic and aerobic biodegradation

High amounts of antibiotics, used in animal farms for the prevention of diseases, are released back into the natural environment with a possible risk of chronic toxicity to other organisms and the development of antibiotic-resistant genes. The antibiotics, including sulfonamides and β-lactams, detected in swine wastewater were between 99.2 and 339.3 μg/L. The typical on-site swine wastewater treatment process turned out to be inadequate, reflected by the high conventional contaminant and antibiotic residuals even under a long hydraulic residence time (HRT, around 2-3 months). The lab-scale combined anaerobic and aerobic biological process showed that anaerobic digestion was mainly responsible for chemical oxygen demand (COD) reduction and aerobic biodegradation contributed significantly to antibiotic removal, with overall removal efficiencies of 95% for COD and 92% for antibiotics under a short HRT of 3.3 days. The removal of selected antibiotics could be a combined result of biodegradation, the balance between adsorption and desorption, and the transformation between antibiotic metabolites and their parent antibiotics. The current work provides valuable insights into the appropriate selection and optimisation of biological processes for the treatment of typical wastewater with high COD and trace antibiotics.

Isolation of Quercetin from Rubus fruticosus, Their Concentration through NF/RO Membranes, and Recovery through Carbon Nanocomposite. A Pilot Plant Study

In this study, an attempt has been made to devise a method for a large-scale production of quercetin from a medicinal plant. The natural products are first isolated from plants and then synthesized commercially. During their synthesis, a number of impurities or side products are also formed, most of which are carcinogenic. Plant products have limited side effects. Therefore, they are considered safe to be used for systemic uses. In the Rubus fruticosus fruit, the ethyl acetate extract was loaded to 50 optimized silica gel columns. The effluents of columns were passed through the membrane system for concentration. A 100% recovery was achieved from the drain pipe in case of reverse osmosis membrane when the specified rely of the pilot plant was set on 25% rejection. About 95% recovery was achieved through the NF membrane while the 5% loss in permeate was recovered through magnetic carbon nanocomposite (characterized through a bar magnet, SEM, XRD, and EDX). The equilibrium time of adsorption was 83 min and followed by pseudo-first-order kinetics. The adsorption equilibrium data fitted well to the Langmuir isotherm model. Through the devised method, quercetin was successfully concentrated with high efficiencies; however, further studies are needed to validate the method.

Multifunctional β-Cyclodextrin Polymer for Simultaneous Removal of Natural Organic Matter and Organic Micropollutants and Detrimental Microorganisms from Water

Natural organic matter (NOM), organic micropollutants (OMPs), and detrimental microorganisms are three major pollutants that affect water quality. To remove these pollutants, a quaternary ammonium-functionalized β-cyclodextrin polymer (β-CDP) is successfully synthesized in the aqueous phase. The N₂ and CO₂ adsorption/desorption analysis showed that the polymer mainly contains ultra-micropores (<1 nm), with a Langmuir surface area of 89 m² g^-1. Two kinds of NOM, humic acid and fulvic acid, and five OMPs, 2-naphthol (2-NO), 3-phenylphenol (3-PH), 2,4,6-trichlorophenol (2,4,6-TCP), bisphenol A (BPA), and bisphenol S (BPS), were selected as model pollutants to study the performance of β-CDP and three kinds of commercial adsorbents, including granular activated carbon, DARCO-AC, and two resins, XAD-4 and D-201, were used for comparison. The polymer shows ultrarapid adsorption kinetics for the removal of these pollutants, with pseudo-second-order rate constants two to three orders of magnitude higher than that of the commercial activated carbon and resins. Due to the different adsorption sites of NOM and OMPs, β-CDP can simultaneously remove these pollutants without competitive adsorption. The maximum adsorption capacity of β-CDP for HA, FA, 2-NO, 3-PH, 2,4,6-TCP, BPA, and BPS based on the Langmuir model is 40, 166, 74, 101, 108, 103, and 117 mg g^-1, respectively. After use, the polymer can be easily regenerated at room temperature. In addition, β-CDP also showed excellent bactericidal properties due to the quaternary ammonium groups. At a concentration of 15 g L^-1, β-CDP can remove 98% of the tested Escherichia coli. Moreover, the synthesis of β-CDP is simple, green, and easy to industrialize. All of these findings indicate that β-CDP, as an ideal multifunctional material, presents potential for practical applications for water treatment and disinfection.

Removal of metronidazole from aqueous media by C. vulgaris

This current study investigated the removal of metronidazole from aqueous media by C. vulgaris. Two different initial sizes of inoculum (0.05 and 0.5 g L^-1) were tested for a wide concentration range of metronidazole (1-50 μM). The effect of metronidazole concentrations on biomass production was studied for 20 days. The exopolymeric substances (EPS) were quantified and correlated with the removal of antibiotics from aqueous media. Specifically, MDZ stimulated the production of EPS in C. vulgaris, which played the major role in the adsorption of this antibiotic. Also, metronidazole significantly influenced the zeta potential of C. vulgaris in the test cultures, indicating a change in surface characteristics. This decrease in surface negative charge caused auto-flocculation phenomena at a stationary phase. Chronic and acute toxicity experiments showed that metronidazole was harmful to C. vulgaris at stationary phase. Results from this study would advance our knowledge on the treatment of metronidazole-contaminated waters with C. vulgaris as a green technology-oriented process.

High-efficiency biodegradation of chloramphenicol by enriched bacterial consortia: Kinetics study and bacterial community characterization

The risk of environmental pollution caused by chloramphenicol has necessitated special attention. Biodegradation has tremendous potential for chloramphenicol removal in the environment. Six chloramphenicol-degrading consortia were acclimated under different culture conditions to investigate their chloramphenicol biodegradation behaviors, and the bacterial community structures were comprehensively characterized. The enriched consortia CL and CH which utilized chloramphenicol as their sole carbon and energy source could thoroughly degrade 120 mg/L chloramphenicol within 5 days, and the mineralization rate reached up to 90%. Chloramphenicol biodegradation kinetics by different enriched consortia fit the modified Gompertz model or the first-order decay model (R²≥0.97). Consortia CL could almost completely degrade 1-500 mg/L CAP with a final mineralization rate of 87.8-91.7%. Chloramphenicol 3-acetate was identified to be a major intermediate of CAP biodegradation by metabolite analysis and enzyme activity assay. 16S rRNA sequencing analysis revealed that the diversities and abundances of the main genera in the enriched consortia were distinct from each other. Forty-one core OTUs belonging to 18 genera were the core bacteria which might be related to chloramphenicol biodegradation. Among them, the genera Sphingomonas, Chryseobacterium, Cupriavidus, Bradyrhizobium, Burkholderia, and Afipia with high abundance may play potential roles for chloramphenicol biodegradation.

Lomefloxacin—Occurrence in the German River Erft, Its Photo-Induced Elimination, and Assessment of Ecotoxicity

Pharmaceuticals in waters represent a worldwide problem of today. Advanced oxidation processes (AOPs) are being researched for elimination of the ecological hazard. Among the substances, the fluoroquinolone antibiotic lomefloxacin was selected for investigation in this study. Lomefloxacin (LOM) was found in the German river Erft. Near and far ultraviolet (UVA, UVC) radiation were used as AOPs and compared for efficiency depending on pH, water matrix, and catalysts. Chemical kinetics description revealed that UVC at pH 8–9 led to the fastest degradation of LOM. The catalysts hydrogen peroxide and titanium dioxide had only limited influence on the degradation rate. Seven novel transformation products were structurally identified by high-resolution higher-order mass spectrometry. Ecotoxicity of the novel and known compounds was assessed by quantitative structure-activity relationship (QSAR) analysis. In addition, irradiation time dependent minimal, and half-maximal inhibitory concentrations (MIC, IC50) of LOM solutions were determined and suggested as ecotoxicological hazard indicators. From MIC and kinetic rate constants, the irradiation time required for compound and activity removal could be predicted.