Design of High-Mobility Diketopyrrolopyrrole-Based π-Conjugated Copolymers for Organic Thin-Film Transistors

Conjugated Polymer Heteroatom Engineering Enables High Detectivity Symmetric Ambipolar Phototransistors

Solution-processed high-performing ambipolar organic phototransistors (OPTs) can enable low-cost integrated circuits. Here, a heteroatom engineering approach to modify the electron affinity of a low band gap diketopyrrolopyrole (DPP) co-polymer, resulting in well-balanced charge transport, a more preferential edge-on orientation and higher crystallinity, is demonstrated. Changing the comonomer heteroatom from sulfur (benzothiadiazole (BT)) to oxygen (benzooxadiazole (BO)) leads to an increased electron affinity and introduces higher ambipolarity. Organic thin film transistors fabricated from the novel PDPP-BO exhibit charge carrier mobility of 0.6 and 0.3 cm2 Vs⁻1 for electrons and holes, respectively. Due to the high sensitivity of the PDPP-based material and the balanced transport in PDPP-BO, its application as an NIR detector in an OPT architecture is presented. By maintaining a high on/off ratio (9 × 104), ambipolar OPTs are shown with photoresponsivity of 69 and 99 A W⁻1 and specific detectivity of 8 × 107 for the p-type operation and 4 × 109 Jones for the n-type regime. The high symmetric NIR-ambipolar OPTs are also evaluated as ambipolar photo-inverters, and show a 46% gain enhancement under illumination.

A Three-in-One Hybrid Strategy for High-Performance Semiconducting Polymers Processed from Anisole

The development of semiconducting polymers with good processability in green solvents and competitive electrical performance is essential for realizing sustainable large-scale manufacturing and commercialization of organic electronics. A major obstacle is the processability-performance dichotomy that is dictated by the lack of ideal building blocks with balanced polarity, solubility, electronic structures, and molecular conformation. Herein, through the integration of donor, quinoid and acceptor units, an unprecedented building block, namely TQBT, is introduced for constructing a serial of conjugated polymers. The TQBT, distinct in non-symmetric structure and high dipole moment, imparts enhanced solubility in anisole-a green solvent-to the polymer TQBT-T. Furthermore, PTQBT-T possess a highly rigid and planar backbone owing to the nearly coplanar geometry and quinoidal nature of TQBT, resulting in strong aggregation in solution and localized aggregates in film. Remarkably, PTQBT-T films spuncast from anisole exhibit a hole mobility of 2.30 cm2 V-1 s-1, which is record high for green solvent-processable semiconducting polymers via spin-coating, together with commendable operational and storage stability. The hybrid building block emerges as a pioneering electroactive unit, shedding light on future design strategies in high-performance semiconducting polymers compatible with green processing and marking a significant stride towards ecofriendly organic electronics.

Optimized Incorporation of Furan into Diketopyrrolopyrrole-Based Conjugated Polymers for Organic Field-Effect Transistors

Flexible electronics have received considerable attention in the past decades due to their promising application in rollable display screens, wearable devices, implantable devices, and other electronic applications. In particular, conjugated polymers are favored for flexible electronics due to their mechanical flexibility and potential for solution-processed fabrication techniques, such as blade-coating, roll-to-roll printing, and high-throughput printing allowing for high-performance transistor devices. Thiophene is the prevailing conjugated unit to construct these conjugated polymers due to its favorable electronic properties. On the other hand, furans are among the few conjugated moieties that are easily derived from bio renewable resources. To promote sustainability, we selectively introduced furan into the conjugated backbone of a high-mobility polymer scaffold and systematically studied the effect on the microstructure and charge transport. We show that partially and selectively replacing thiophene units with furan can yield nearly comparable performance compared to the all-thiophene polymer. This strategy offers an improvement in the sustainability of the polymer by incorporating bio-sourced furan without sacrificing the high-performance characteristics. Meanwhile, polymers with incorrect or complete furan incorporation show reduced mobilities. This work serves to develop coherent structure-morphology-performance relationships; such knowledge will establish guidelines for the future development of sustainable, furan-based conjugated materials.

Pre-Endcapping of Hyperbranched Polymers toward Intrinsically Stretchable Semiconductors with Good Ductility and Carrier Mobility

The advancement of semiconducting polymers stands as a pivotal milestone in the quest to realize wearable electronics. Nonetheless, endowing semiconductor polymers with stretchability without compromising their carrier mobility remains a formidable challenge. This study proposes a "pre-endcapping" strategy for synthesizing hyperbranched semiconducting polymers (HBSPs), aiming to achieve the balance between carrier mobility and stretchability for organic electronics. The findings unveil that the aggregates formed by the endcapped hyperbranched network structure not only ensure efficient charge transport but also demonstrate superior tensile resistance. In comparison to linear conjugated polymers, HBSPs exhibit substantially larger crack onset strains and notably diminished tensile moduli. It is evident that the HBSPs surpass their linear counterparts in terms of both their semiconducting and mechanical properties. Among HBSPs, HBSP-72h-2.5 stands out as the preeminent candidate within the field of inherently stretchable semiconducting polymers, maintaining 93% of its initial mobility even when subjected to 100% strain (1.41 ± 0.206 cm2 V-1 s-1). Furthermore, thin film devices of HBSP-72h-2.5 remain stable after undergoing repeated stretching and releasing cycles. Notably, the mobilities are independent of the stretching directions, showing isotropic charge transport behavior. The preliminary study makes this "pre-endcapping" strategy a potential candidate for the future design of organic materials for flexible electronic devices.

Stretchable Semiconducting Polymers with Hydrogen-Bonding-Capable Conjugation Breakers: Synthesis and Application in Organic Thin-Film Transistors

Diketopyrrolopyrrole (DPP)-based conjugated copolymers are important organic semiconductors for applications in high-efficiency organic thin-film transistors (OTFTs). However, the direct application of these polymers with rigid backbones in stretchable devices has limitations. In this study, we designed and synthesized three kinds of DPPBT-based copolymers, DPPBT-A1, DPPBT-A3, and DPPBT-A5, which have amide-coupled alkylene conjugation breakers capable of hydrogen bonding. Linkers with different segment lengths were copolymerized with DPP and bithiophene (BT) backbone units. A DPP-based copolymer with alternating BT moieties, DPPBT, was synthesized as a reference fully conjugated copolymer. The synthesized polymers with freely rotational backbone linkers have sufficient flexibility to develop ordered phase domains, even in thin films, in comparison to the reference copolymer. However, the introduction of the conjugation breakers, which disconnect the intramolecular π-π overlapping, tends to decrease the hole mobility (μ) from 0.76 to 0.20 cm2 V-1 s-1 in the corresponding OTFT devices. The TFT fabricated using DPPBT-A3 showed a mobility of 0.50 cm2 V-1 s-1, and the mobility value did not show a significant change even when elongated by more than 50%. Therefore, the molecular design strategy of introducing amide-coupled alkylene conjugation breakers into conjugated polymer chains can contribute significantly to the development of high-mobility stretchable conjugated polymers in future.

Novel Divinyl-Flanked Diketopyrrolopyrrole Polymer, Based on a Dimerization Strategy for High-Performance Organic Field-Effect Transistors

In this communication, we report a novel acceptor structural unit, TVDPP, that can be distinguished from classical materials based on TDPP structures. By designing a synthetic route via retrosynthetic analysis, we successfully prepared this monomer and further prepared polymer P2TVDPP with high yield using a Stille-coupling polymerization reaction. The polymer showed several expected properties, such as high molecular weight, thermal stability, full planarity, small π-π stacking distance, smooth interface, and so on. The absorption spectra and energy levels of the polymer were characterized via photochemical and electrochemical analysis. The organic field-effect transistor (OFET), which is based on P2TVDPP, exhibited excellent carrier mobility and an on/off current ratio of 0.41 cm2 V-1 s-1 and ~107, respectively, which is an important step in expanding the significance of DPP-based materials in the field of optoelectronic devices and organic electronics.

Preparation of Novel Organic Polymer Semiconductor and Its Properties in Transistors through Collaborative Theoretical and Experimental Approaches

Conjugated polymer semiconductors based on donor-acceptor structures are commonly employed as core materials for optoelectronic devices in the field of organic electronics. In this study, we designed and synthesized a novel acceptor unit thiophene-vinyl-diketopyrrolopyrrole, named TVDPP, based on a four-step organic synthesis procedure. Stille coupling reactions were applied with high yields of polymerization of TVDPP with fluorinated thiophene (FT) monomer. The molecular weight and thermal stability of the polymers were tested and showed high molecular weight and good thermal stability. Theoretical simulation calculations and 2D grazing-incidence wide-angle X-ray scattering (GIWAXS) tests verified the planarity of the material and excellent stacking properties, which are favorable for achieving high carrier mobility. Measurements based on the polymer as an organic thin film transistor (OTFT) device were carried out, and the mobility and on/off current ratio reached 0.383 cm2 V-1 s-1 and 104, respectively, showing its great potential in organic optoelectronics.

Molecular Structure and Conformational Design of Donor-Acceptor Conjugated Polymers to Enable Predictable Optoelectronic Property

Tuning the optoelectronic properties of donor-acceptor conjugated polymers (D-A CPs) is of great importance in designing various organic optoelectronic devices. However, there remains a critical challenge in precise control of bandgap through synthetic approach, since the chain conformation also affects molecular orbital energy levels. Here, D-A CPs with different acceptor units are explored that show an opposite trend in energy band gaps with the increasing length of oligothiophene donor units. By investigating their chain conformation and molecular orbital energy, it is found that the molecular orbital energy alignment between donor and acceptor units plays a crucial role in dictating the final optical bandgap of D-A CPs. For polymers with staggered orbital energy alignment, the higher HOMO with increasing oligothiophene length leads to a narrowing of the optical bandgap despite decreased chain rigidity. On the other hand, for polymers with sandwiched orbital energy alignment, the increased band gap with increasing oligothiophene length originates from the reduction of bandwidth due to more localized charge density distribution. Thus, this work provides a molecular understanding of the role of backbone building blocks on the chain conformation and bandgaps of D-A CPs for organic optoelectronic devices through the conformation design and segment orbital energy alignment.

Semiconducting Polymers Based on Simple Electron-Deficient Cyanated trans-1,3-Butadienes for Organic Field-Effect Transistors

Developing high-performance but low-cost n-type polymers remains a significant challenge in the commercialization of organic field-effect transistors (OFETs). To achieve this objective, it is essential to design the key electron-deficient units with simple structures and facile preparation processes, which can facilitate the production of low-cost n-type polymers. Herein, by sequentially introducing fluorine and cyano functionalities onto trans-1,3-butadiene, we developed a series of structurally simple but highly electron-deficient building blocks, namely 1,4-dicyano-butadiene (CNDE), 3-fluoro-1,4-dicyano-butadiene (CNFDE), and 2,3-difluoro-1,4-dicyano-butadiene (CNDFDE), featuring a highly coplanar backbone and deep-positioned lowest unoccupied molecular orbital (LUMO) energy levels (-3.03-4.33 eV), which render them highly attractive for developing n-type semiconducting polymers. Notably, all these electron-deficient units can be easily accessed by a two-step high-yield synthetic procedure from low-cost raw materials, thus rendering them highly promising candidates for commercial applications. Upon polymerization with diketopyrrolopyrrole (DPP), three copolymers were developed that demonstrated unipolar n-type transport characteristics in OFETs with the highest electron mobility of >1 cm2  V-1  s-1 . Hence, CNDE, CNFDE, and CNDFDE represent a class of novel, simple, and efficient electron-deficient units for constructing low-cost n-type polymers, thereby providing valuable insight for OFET applications.

Synergistic Use of All-Acceptor Strategies for the Preparation of an Organic Semiconductor and the Realization of High Electron Transport Properties in Organic Field-Effect Transistors

The development of n-type organic semiconductor materials for transporting electrons as part of logic circuits is equally important to the development of p-type materials for transporting holes. Currently, progress in research on n-type materials is relatively backward, and the number of polymers with high electron mobility is limited. As the core component of the organic field-effect transistor (OFET), the rational design and judicious selection of the structure of organic semiconductor materials are crucial to enhance the performance of devices. A novel conjugated copolymer with an all-acceptor structure was synthesized based on an effective chemical structure modification and design strategy. PDPPTT-2Tz was obtained by the Stille coupling of the DPPTT monomer with 2Tz-SnMe3, which features high molecular weight and thermal stability. The low-lying lowest unoccupied molecular orbital (LUMO) energy level of the copolymer was attributed to the introduction of electron-deficient bithiazole. DFT calculations revealed that this material is highly planar. The effect of modulation from a donor-acceptor to acceptor-acceptor structure on the improvement of electron mobility was significant, which showed a maximum value of 1.29 cm2 V-1 s-1 and an average value of 0.81 cm2 V-1 s-1 for electron mobility in BGBC-based OFET devices. Our results demonstrate that DPP-based polymers can be used not only as excellent p-type materials but also as promising n-type materials.

A Hybrid Acceptor-Modulation Strategy: Fluorinated Triple-Acceptor Architecture for Significant Enhancement of Electron Transport in High-Performance Unipolar n-Type Organic Transistors

The development of unipolar n-type semiconducting polymers with electron mobility (µ_e ) over 5 cm²  V^-1  s^-1 remains a massive challenge in organic semiconductors. Diketopyrrolopyrrole (DPP) has proven to be a successful unit for high-performance p-type and ambipolar polymers. However, DPP's moderate electron-accepting capability leads to the shallow frontier molecular orbital (FMO) levels of the resultant polymers and hence limit the µ_e in unipolar n-type organic transistors. Herein, this issue has been addressed by using a hybrid acceptor-modulation strategy based on DPP-containing "fluorinated triple-acceptor architecture", namely DPP-difluorobenzothiadiazole-DPP (DFB). Compared with DFB's non-fluorinated counterpart, DFB features deeper FMO levels and a shape-persistent framework. Therefore, a series of DFB-based polymers demonstrate planar backbones and lowered FMO levels by ≈0.10 to 0.25 eV versus that of the control polymer. Intriguingly, all DFB-polymers exhibit excellent unipolar n-type transistor performances. Notably, a full-locked backbone conformation and high crystallinity with crystalline coherence length of 524 Å are observed for pDFB-TF, accounting for its high µ_e of 5.04 cm²  V^-1  s^-1 , which is the highest µ_e value for DPP-based unipolar n-type polymers reported to date. This work demonstrates that the strategy of "fluorinated triple-acceptor architecture" opens a new path towards high-performance unipolar n-type semiconducting polymers.

Silver-catalyzed direct selanylation of indoles: synthesis and mechanistic insights

Herein we describe the Ag(i)-catalyzed direct selanylation of indoles with diorganoyl diselenides. The reaction gave 3-selanylindoles with high regioselectivity and also allowed direct access to 2-selanylindoles when the C3 position of the indole ring was blocked via a process similar to Plancher rearrangement. Experimental analyses and density functional theory calculations were carried out in order to picture the reaction mechanism. Among the pathways considered (via concerted metalation-deprotonation, Ag(iii), radical, and electrophilic aromatic substitution), our findings support a classic electrophilic aromatic substitution via Lewis adducts between Ag(i) and diorganoyl diselenides. The results also afforded new insights into the interactions between Ag(i) and diorganoyl diselenides.

Benzimidazolone-Dioxazine Pigments-Based Conjugated Polymers for Organic Field-Effect Transistor

Molecules based on benzimidazolone-dioxazine are known as blue/violet pigments and have been commercialized for decades. However, unfavorable solubility limits the application of these structures as building blocks of conjugated polymers despite their low band gaps. Herein, a series of donor-acceptor conjugated polymers containing soluble benzimidazolone-dioxazine structures as the acceptors and oligothiophene as donors are synthesized and investigated. With increasing numbers of thiophene rings, the steric hindrance diminishes and high molecular weight polymers can be achieved, leading to an improved performance in organic field effect transistor devices. The hole mobility of polymers with three to six thiophene units is in the order of 10^-1 cm² V^-1 s ^-1 . Among all the polymers, polymer P3 with three thiophene units between benzimidazolone-dioxazine structures shows the best hole mobility of 0.4 cm² V^-1 s ^-1 . Grazing-incidence wide-angle X-ray scattering results reveal that the high mobility of organic field-effect transistors (OFETs) can be accredited by matched donor-acceptor packing in the solid thin films.

Chain-Extending Polymerization for Significant Improvement in Organic Thin-Film Transistor Performance

To achieve high-performance polymer semiconductors, it is crucially important to explore novel and effective synthesis strategies. Here, chain-extending polymerization as a synthesis strategy to design polymer semiconductors is introduced. Furthermore, we demonstrate its superiority over a conventional synthesis strategy─one-pot polymerization. Diketopyrrolopyrrole-thieno[3,2-b]thiophene-containing polymers (PDPPTT and PDPPTT-vinylene) are used in this study. PDPPTT and PDPPTT-vinylene are synthesized through one-pot polymerization and chain-extending polymerization, respectively. The utilization of this novel strategy enhances the hole/electron mobilities of PDPPTT-vinylene to up to 3.70/2.96 cm² V^-1 s^-1 (compared to 2.71/0.63 cm² V^-1 s^-1 for PDPPTT), thereby achieving the required performance for organic circuits like inverters and ring oscillators. The significant improvement in the transistor performance of PDPPTT-vinylene is attributed to the introduced vinylene linking units during the polymerization process, which can fine-tune the electronic structure, expand π-conjugation, and induce stronger intermolecular π-π interactions with more significant crystallization. These results demonstrate that chain-extending polymerization is an effective synthesis strategy for developing high-performance polymer semiconductors.

Determination of nitrite in food based on its sensitizing effect on cathodic electrochemiluminescence of conductive PTH-DPP films

Herein, a novel strategy for electrochemiluminescence (ECL) detection of nitrite based on its sensitization effect on cathode ECL emission of 3,6-di(2-thienyl)-2,5-dihydropyrrolo [3,4-c] pyrrole-1,4-dione (TH-DPP) polymeric films (PTH-DPP) was formulated, by means of a one-step electropolymerization of TH-DPP with a short time on the glassy carbon electrode (GCE). It was shown that the PTH-DPP film-modified GCE exhibited a strong ECL response when S₂O₈^2- was used as a co-reactant. The ECL emission could be greatly enhanced by PTH-DPP with nitrite in a K₂S₂O₈/PBS solution system and occurred at a relatively lower potential in comparison with traditional cathode ECL emitter, leading to high sensitivity and good selectivity. The ECL sensor exhibits excellent linear relationship in the ranges of 0.3 to 100 μM and 100 to 1000 μM for nitrite detection, with an outstanding detection limit of 0.08 μM (S/N = 3). The ECL sensor provides an impressive outcome for the detection of practical samples.

Synthesis and Emergent Photophysical Properties of Diketopyrrolopyrrole-Based Supramolecular Self-Assembly

Diketopyrrolopyrrole (DPP)-based molecular semiconductors exhibit intriguing optical and charge transport properties. Herein, we rationally design a series of electronically identical but structurally distinct Hamilton receptor (HR)-based supramolecular assembly of DPP. The HR endows supramolecular assemblies via hydrogen bonding with enhanced structural ordering and excitonic couplings. The mechanism of supramolecular self-assembly was probed by diffusion ordered spectroscopy (DOSY) nuclear magnetic resonance (NMR) and solid-state IR spectroscopy studies. We investigated the morphology of self-assembly, photophysical and electrochemical properties and compared them with the identical DPP molecular structures without HRs. The microstructure of self-assembly was probed with atomic force microscopy in thin films. Subsequently, the influence of solid-state packing was studied by single-crystal X-ray diffraction. The single-crystal structure of HR-TDPP-C₂₀ reveals slipped stack arrangements between the two neighboring chromophores with π-π stacking distance and slip angle of 3.55 Å and 35.4°, respectively. Notably, the slight torsional angle of 1° between thiophene and lactam rings and small π-π stacking distance suggest a significant intermolecular coupling between thiophene (D) and lactam (A) rings. This intramolecular coupling between two π-π chromophore stacks manifests in their optical properties. In this manuscript, we report rational design and synthesis of supramolecular self-assembly of DPP with a collection of compelling structural and optical properties.

Small-molecule ambipolar transistors

Ambipolar transistor properties have been observed in various small-molecule materials. Since a small energy gap is necessary, many types of molecular designs including extended π-skeletons as well as the incorporation of donor and acceptor units have been attempted. In addition to the energy levels, an inert passivation layer is important to observe ambipolar transistor properties. Ambipolar transport has been observed in extraordinary π-electron systems such as antiaromatic compounds, biradicals, radicals, metal complexes, and hydrogen-bonded materials. Several donor/acceptor cocrystals show ambipolar transport as well.

Controlling Solution-State Aggregation and Solid-State Microstructures of Conjugated Polymers by Tuning Backbone Conformation

Molecular ordering of conjugated polymers both in solution-state aggregates and in solid-state microstructures is a determining factor of the charge transport properties in optoelectronic devices. However, the effect of backbone conformation in conjugated polymers on assembly structures is still unclear. Herein, to understand such backbone conformation effect, three novel chlorinated benzodifurandionge-based oligo(p-phenylene vinylene) (BDOPV) polymers are systematically developed. These BDOPV-based polymers exhibit significantly twisted backbone conformation (near 90° interunit torsion angle) between conjugated units, which can prevent polymer chains from forming ordered assembly structures by increasing conformational energy penalty in closely packed chains. A higher rotational barrier of the torsion angle would further prevent polymer chains from assembling, finally resulting in non-aggregated chains in solution and highly disordered solid-state packing structures. This work will deepen the understanding of the relationship between polymer backbone conformation and assembly structures, contributing to the exploration of the structure-property relationship of polymers. This article is protected by copyright. All rights reserved.

Photocatalytic Water-Splitting by Organic Conjugated Polymers: Opportunities and Challenges

The future challenges associated with the shortage of fossil fuels and their current environmental impacts intrigued the researchers to look for alternative ways of generating green energy. Solar-driven water splitting into oxygen and hydrogen is one of those advanced strategies. Researchers have studied various semiconductor materials to achieve potential results. However, it encountered multiple challenges such as high cost, low photostability and efficiency, and required multistep modifications. The conjugated polymers (CPs) have emerged as promising alternatives for conventional inorganic semiconductors. The CPs offer low cost, sufficient light absorption efficiency, excellent photo and chemical stability, and molecular optoelectronic tunable characteristics. Furthermore, organic CPs also present higher flexibility to tune the basic framework of the backbone of the polymers, amendments in the sidechain to incorporate desired functionalities, and much-needed porosity to serve better for photocatalytic applications. This review article summarizes the recent advancements made in visible-light-driven water splitting covering the aspects of synthetic strategies and experimental parameters employed for water splitting reactions with special emphasis on conjugated polymers such as linear CPs, planarized CPs, graphitic carbon nitride (g-C₃ N₄ ), conjugated microporous polymers (CMPs), covalent organic frameworks (COFs), and conjugated polymer-based nanocomposites (CPNCs). The current challenges and future prospects have also been described briefly.

Development of hybrid coarse-grained atomistic models for rapid assessment of local structuring of polymeric semiconductors

Decades of work in the field of computational study of semiconducting polymers using atomistic models illustrate the challenges of generating equilibrated models for this class of materials. While adopting a coarse-grained model can be helpful, the process of developing a suitable model is particularly non-trivial and time-consuming for semiconducting polymers due to a large number of different interactions with some having an anisotropic nature. This work introduces a procedure for the rapid generation of a hybrid model for semiconducting polymers where atoms of secondary importance (those in the alkyl side chains) are transformed into coarse-grained beads to reduce the computational cost of generating an equilibrated structure. The parameters are determined from easy-to-equilibrate simulations of very short oligomers and the model is constructed to enable a very simple back-mapping procedure to reconstruct geometries with atomistic resolution. The model is illustrated for three related polymers containing DPP (diketopyrrolopyrrole) to evaluate the transferability of the potential across different families of polymers. The accuracy of the model, determined by comparison with the results of fully equilibrated simulations of the same material before and after back-mapping, is fully satisfactory for two out of the three cases considered. We noticed that accuracy can be determined very early in the workflow so that it is easy to assess when the deployment of this method is advantageous. The hybrid representation can be used to evaluate directly the electronic properties of structures sampled by the simulations.

Exciton Dynamics of a Diketo-Pyrrolopyrrole Core for All Low-Lying Electronic Excited States Using Density Functional Theory-Based Methods

Ab initio treatments of interexcited state internal conversion (IC) are more often than not missing from exciton dynamic descriptions, because of their inherent complexity. Here, we define "interexcited state IC" as a same-spin nonradiative transition between states i and j, where i ≠ j ≠ 0. Competing directly with multiexciton processes such as singlet fission or triplet photoupconversion, inclusion of this mechanism in the narrative of molecular photophysics would allow for strategic synthesis of chromophores for more efficient photon-harvesting applications. Herein, we present a robust formalism which can model these rates using density functional theory (DFT)-based methods within the Franck-Condon and Herzberg-Teller regime. Using an unsubstituted diketo-pyrrolopyrrole (DPP) core as a case study, we illustrate the exciton dynamics along the first four excited states for both singlet and triplet manifolds, showing ultrafast same-spin transfer mechanisms due to all excited states, excluding the first triplet level, being in close energetic proximity (within 0.8 eV of each other). The resulting electron same-spin rates outcompete the electron spin-flipping intersystem crossing (ISC) rates, with excitons firmly obeying Kasha's rule as they cascade down from the high-lying excited states toward the lower states. Furthermore, we calculated that only the first singlet excited state displayed a reasonable probability of triplet exciton generation, of ∼40%, with a near-zero chance of the exciton reverting to the singlet manifold once the electron-hole pair are of parallel spin.

Organic Nanoparticles Based on D-A-D Small Molecule: Self-Assembly, Photophysical Properties, and Synergistic Photodynamic/Photothermal Effects

Cancer is one of the major diseases threatening human health. Traditional cancer treatments have notable side-effects as they can damage the immune system. Recently, phototherapy, as a potential strategy for clinical cancer therapy, has received wide attention due to its minimal invasiveness and high efficiency. Herein, a small organic molecule (PTA) with a D-A-D structure was prepared via a Sonogashira coupling reaction between the electron-withdrawing dibromo-perylenediimide and electron-donating 4-ethynyl-N,N-diphenylaniline. The amphiphilic organic molecule was then transformed into nanoparticles (PTA-NPs) through the self-assembling method. Upon laser irradiation at 635 nm, PTA-NPs displayed a high photothermal conversion efficiency (PCE = 43%) together with efficient reactive oxygen species (ROS) generation. The fluorescence images also indicated the production of ROS in cancer cells with PTA-NPs. In addition, the biocompatibility and photocytotoxicity of PTA-NPs were evaluated by 3-(4,5-Dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay and live/dead cell co-staining test. Therefore, the as-prepared organic nanomaterials were demonstrated as promising nanomaterials for cancer phototherapy in the clinic.

Design strategies for improving the crystallinity of covalent organic frameworks and conjugated polymers: a review

Highly crystalline covalent organic frameworks (COFs) or conjugated polymers (CPs) are very important and highly desirable because these materials would display better performance in diverse devices and provide more structure-property related information. However, how to achieve highly crystalline or single-crystal COFs and CPs is very challenging. Recently, many research studies have demonstrated the possibility of enhancing the crystallinity of COFs and CPs. Thus, it is timely to offer an overview of the important progress in improving the crystallinity of COFs and CPs from the viewpoint of design strategies. These strategies include polycondensation reaction optimization, improving the planarity, fluorine substitution, side chain engineering, and so on. Furthermore, the challenges and perspectives are also discussed to promote the realization of highly crystalline or single-crystal COFs and CPs.

Revealing the Side-Chain-Dependent Ordering Transition of Highly Crystalline Double-Cable Conjugated Polymers

We developed a series of highly crystalline double-cable conjugated polymers for application in single-component organic solar cells (SCOSCs). These polymers contain conjugated backbones as electron donor and pendant perylene bisimide units (PBIs) as electron acceptor. PBIs are connected to the backbone via alkyl units varying from hexyl (C₆ H₁₂ ) to eicosyl (C₂₀ H₄₀ ) as flexible linkers. For double-cable polymers with short linkers, the PBIs tend to stack in a head-to-head fashion, resulting in large d-spacings (e.g. 64 Å for the polymer P12 with C₁₂ H₂₄ linker) along the lamellar stacking direction. When the length of the linker groups is longer than a certain length, the PBIs instead adopt a more ordered packing likely via H-aggregation, resulting in short d-spacings (e.g. 50 Å for the polymer P16 with C₁₆ H₃₂ linker). This work highlights the importance of linker length on the molecular packing of the acceptor units and the influences on the photovoltaic performance of SCOSCs.

Effects of the Polarity and Bulkiness of End-Functionalized Side Chains on the Charge Transport of Dicyanovinyl-End-Capped Diketopyrrolopyrrole-Based n-Type Small Molecules

When designing organic semiconductors, side-chain engineering is as important as modifying the conjugated backbone, which has a significant impact on molecular ordering, morphology, and thus electronic device performance. We have developed three dicyanovinyl-end-capped donor-acceptor diketopyrrolopyrrole-based n-type small molecules (C2C9CN, SiC4CN, and EH4PCN) bearing an identical length of alkyl spacer yet different end-functionalized side chains (i.e., alkyl-, siloxane-, and phosphonate-end pendants). The effects of the end-functionalized side chains on the intrinsic molecular properties, microstructure, and charge transport of the small-molecule series were investigated. In comparison with the alkyl-end side chains, incorporating siloxane-end side chains into the backbone facilitates 2D edge-on oriented high intergrain connectivity/crystallinity and compatibility with the substrate surface, whereas the phosphonate-end analogues have an adverse effect on the film-forming quality due to high polarity. Thereby, an organic field-effect transistor fabricated by SiC4CN shows the best electron mobility up to 1.59 × 10-1 cm2 V-1 s-1 along with a high current on/off ratio >105. This study contributes to our understanding of the role of the end-functionalized side chains (e.g., the effects of polarity and bulkiness of the end groups) for the development of high-performance semiconductors.

Controlled Assembly of Conjugated Ladder Molecules with Different Bridging Structures toward Optoelectronic Application

Structural design of organic π-conjugated small molecules allows the energy band structure and electronic properties of the molecules to be tuned as needed, which provides a feasible strategy for enhancing the performance of optoelectronic devices. The introduction of bridging structures is a common structural modification method to adjust the rigidity and coplanarity of the molecular backbone, thus affecting the molecular packing. However, patterning of organic single-crystalline microstructures based on conjugated ladder molecules with different bridging structures still remains challenging for large-area integration of optoelectronic devices. In this paper, a controlled dewetting process is applied to obtain organic single-crystalline arrays with precise positioning and a regular morphology based on two isomers with silicon-oxygen bridging and their two carbon-oxygen-bridged analogues. Molecules with different bridging structures show disparate packing models due to the difference of dihedral angles and ring tensions. A microwire-array ultraviolet photodetector based on the oxygen-silicon-bridging ladder molecule exhibits a high light on/off ratio of 24 and a responsivity of 0.63 mA W^-1 owing to the effective π-π stacking governed by the molecular planarity. This work not only provides a universal method for the integration of organic optoelectronic devices but also explains the effect of bridging structure engineering on molecular assembly and optoelectronic performance.

Crystalline Domain Formation to Enable High-Performance Polymer Thermoelectrics Inspired by Thermocleavable Materials

Improving the electrical conductivity is an important role in realizing high thermoelectric performance of solution-processable polymers. Herein, a simple and robust approach to boost the mobility and doping efficiency of a diketopyrrolopyrrole-based copolymer with the introduction of thermocleavable side chains (PDPPS-X, where X is the molar ratio of the thermocleavable side chains and alkyl chains) is first provided. Notably, the incorporated thermocleavable groups can be effectively removed after thermal treatment and therefore contribute to the crystalline domain formation via hydrogen-bonded networks, which is critical for conductivity enhancements. Grazing incidence wide-angle X-ray scattering (GIWAXS) patterns give a clear indication that the thermal treatment of PDPPS-5 can greatly improve the structural arrangement, resulting in a significantly enhanced hole mobility (5.4 times that of PDPPS-0 without thermocleavable chains). Compared to PDPPS-0, a larger Fermi level shift is observed after doping PDPPS-5 with FeCl₃, reflecting a better doping efficiency. Consequently, remarkably improved conductivity and power factor are achieved by PDPPS-5 after doping with 0.03 M FeCl₃ at room temperature, which are about 2.2 and 3.5 times higher than that of PDPPS-0 at the same testing condition, respectively. Moreover, PDPPS-5 achieved a maximum power factor of 57.5 μW m^-1 K^-2 at 404 K.

Single-Molecule Charge-Transport Modulation Induced by Steric Effects of Side Alkyl Chains

The experimental investigation of side-chain effects on intramolecular charge transport in π-conjugated molecules is essential but remains challenging. Herein, the dependence of intra-molecular conductance on the nature of branching alkyl chains is investigated through a combination of the scanning tunneling microscope break junction (STM-BJ) technique and density functional theory. Three thiophene-flanked diketopyrrolopyrrole (DPP) derivatives with different branching alkyl chains (isopentane, 3-methylheptane, and 9-methylnonadecane) are used with phenylthiomethyl groups as the anchoring groups. The results of single-molecule conductance measurements show that as the alkyl chain becomes longer, the torsional angles between the aromatic rings increase due to steric crowding, and therefore, the molecular conductance of DPP decreases due to reduction in conjugation. Both theoretical simulations and ¹ H NMR spectra demonstrate that the planarity of the DPPs is directly reduced after introducing longer branching alkyl chains, which leads to a reduced conductance. This work indicates that the effect of the insulating side chain on the single-molecule conductance cannot be neglected, which should be considered for the design of future organic semiconducting materials.

Conjugated Conductive Polymer Materials and its Applications: A Mini-Review

Since their discovery 50 years ago, conjugated conducting polymers have received increasing attention owing to their unique conductive properties and potential applications in energy storage, sensors, coatings, and electronic devices such as organic field-effect transistors, photovoltaic cells, and light-emitting devices. Recently, these materials have played a key role in providing a more comfortable environment for humans. Consequently, the development of novel, high-performance conjugated conductive materials is crucial. In this mini-review, the progress of conjugated conductive materials in various applications and the relationship between the chemical structures and their performances is reviewed. This can aid in the molecular design and development of novel high-performance conjugated polymer materials.

Local structuring of diketopyrrolopyrrole (DPP)-based oligomers from molecular dynamics simulations

The microscopic structure of high mobility semiconducting polymers is known to be essential for their performance but it cannot be easily deduced from the available experimental data. A series of short oligomers of diketopyrrolopyrrole (DPP)-based materials that display high charge mobility are studied by molecular dynamics simulations to understand their local structuring at an atomic level. Different analyses are proposed to compare the ability of different oligomers to form large aggregates and their driving force. The simulations show that the tendency for this class of materials to form aggregates is driven by the interaction between DPP fragments, but this is modulated by the other conjugated fragments of the materials which affect the rigidity of the polymer and, ultimately, the size of the aggregates that are formed. The main structural features and the electronic structure of the oligomers are fairly similar above the glass transition temperature and at room temperature.

A nonchlorinated solvent-processed polymer semiconductor for high-performance ambipolar transistors

Ambipolar polymer semiconductors are potentially serviceable for logic circuits, light-emitting field-effect transistors (LFETs) and polymer solar cells (PSCs). Although several high-performance ambipolar polymers have been developed, their optoelectronic devices are generally processed from toxic chlorinated solvents. To achieve the commercial applications of organic FETs (OFETs), the polymers should be processed from nonchlorinated solvents, instead of chlorinated solvents. However, most conjugated polymers show poor solubility in nonchlorinated solvents. It is of great importance to develop ambipolar polymers that can be processed from nonchlorinated solvents. Here, we develop a nonchlorinated solvent processed polymer named poly[7-fluoro-N, N^′-di(4-decyltetradecyl)-7^′-azaisoindigo-6^′,6^″-(thieno[3,2-b]thiophene-2,5-diyl)-7‴-fluoro-N^″, N‴-di(4-decyltetradecyl)-7^″-azaisoindigo-6,6‴-([2,2^″-bithiophene]-5,5^″-diyl)] (PITTI-BT) by designing a monomer with a large molar mass. The polymer displays good solubility in p-xylene (PX). Well-aligned films of PITTI-BT are achieved by an off-center spin-coating (SC) method. Based on the high-quality films, the OFETs fabricated from PX solution achieve record ambipolar performance with hole and electron mobilities of 3.06 and 2.81 cm² V⁻¹ s⁻¹, respectively. The combination of nonchlorinated solvents and good alignment process offers an effective and eco-friendly approach to obtain high-performance ambipolar transistors.

Recent progress of ultra-narrow-bandgap polymer donors for NIR-absorbing organic solar cells

Solution-processed near-infrared (NIR)-absorbing organic solar cells (OSCs) have been explored worldwide because of their potential as donor:acceptor bulk heterojunction (BHJ) blends. In addition, NIR-absorbing OSCs have attracted attention as high specialty equipment in next-generation optoelectronic devices, such as semitransparent solar cells and NIR photodetectors, owing to their feasibility for real-time commercial application in industry. With the introduction of NIR-absorbing non-fullerene acceptors (NFAs), the value of OSCs has been increasing while organic donor materials capable of absorbing light in the NIR region have not been actively studied yet compared to NIR-absorbing acceptor materials. Therefore, we present an overall understanding of NIR donors.

A Distannylated Monomer of a Strong Electron-Accepting Organoboron Building Block: Enabling Acceptor-Acceptor-Type Conjugated Polymers for n-Type Thermoelectric Applications

Acceptor-acceptor (A-A) copolymerization is an effective strategy to develop high-performance n-type conjugated polymers. However, the development of A-A type conjugated polymers is challenging due to the synthetic difficulty. Herein, a distannylated monomer of strong electron-deficient double B←N bridged bipyridine (BNBP) unit is readily synthesized and used to develop A-A type conjugated polymers by Stille polycondensation. The resulting polymers show ultralow LUMO energy levels of -4.4 eV, which is among the lowest value reported for organoboron polymers. After n-doping, the resulting polymers exhibit electric conductivity of 7.8 S cm^-1 and power factor of 24.8 μW m^-1  K^-2 . This performance is among the best for n-type polymer thermoelectric materials. These results demonstrate the great potential of A-A type organoboron polymers for high-performance n-type thermoelectrics.

Polymorphism of a semi-crystalline diketopyrrolopyrrole-terthiophene polymer

Few semiconducting polymers are known that possess more than one semi-crystalline structure. Guidelines for rationalizing or creating polymorphism in these materials do not exist. Two different semi-crystalline polymorphs, β 1 and β 2, and an amorphous α phase have recently been identified for alternating diketopyrrolopyrrole-quaterthiophene copolymers (PDPP4T). The polymorphs differ structurally by the π-π stacking distance, and electronically by the optical bandgap and charge carrier mobility. Here we investigate the corresponding terthiophene (PDPP3T) derivatives, to study the effect of the relative orientation of adjacent DPP units on the polymorphism. In PDPP3T, the relative orientation of DPP units alternates along the chain, while in PDPP4T it is constant. We show that the two polymorphs, β 1 and β 2, can also be generated for a PDPP3T polymer in solution and thin film. Interestingly, compared to PDPP4T, more solvents can induce the two distinct semi-crystalline polymorphs for PDPP3T via a β 1 → α → β 2 polymorphic transition.