Crystal Growth Regulation of 2D/3D Perovskite Films for Solar Cells with Both High Efficiency and Stability

What Matters for the Charge Transport of 2D Perovskites?

Compared to 3D perovskites, 2D perovskites exhibit excellent stability, structural diversity, and tunable bandgaps, making them highly promising for applications in solar cells, light-emitting diodes, and photodetectors. However, the trade-off for worse charge transport is a critical issue that needs to be addressed. This comprehensive review first discusses the structure of 3D and 2D metal halide perovskites, then summarizes the significant factors influencing charge transport in detail and provides a brief overview of the testing methods. Subsequently, various strategies to improve the charge transport are presented, including tuning A'-site organic spacer cations, A-site cations, B-site metal cations, and X-site halide ions. Finally, an outlook on the future development of improving the 2D perovskites' charge transport is discussed.

Controlled Nucleation and Oriented Crystallization of Methylammonium-Free Perovskites via In Situ Generated 2D Perovskite Phases

Enhancing stability while maintaining high efficiency is among the primary challenges in the commercialization of perovskite solar cells (PSCs). Here, a crystal growth technique assisted by in situ generated 2D perovskite phases has been developed to construct high-quality 2D/3D perovskite films. The in situ generated 2D perovskite serve as templates for regulating the nucleation and oriented crystal growth in the α-FAPbI3-rich film. This led to a high film quality with much reduced trap density and an ultralong carrier lifetime. The obtained perovskite film shows excellent stability under extreme environment conditions (T = 200 °C, RH = 75 ± 5%). The corresponding PSC achieved an efficiency of 26.16% (certified 25.84%), along with excellent operational stability (T93 > 1300 h, T ≅ 50 °C) as well as outstanding high and low temperature cycle stability.

Advances and challenges in molecular engineering of 2D/3D perovskite heterostructures

Organic-inorganic hybrid perovskites have been intensively studied in past decades due to their outstanding performance in solar cells and other optoelectronic devices. Recently, the emergence of two-dimensional/three-dimensional (2D/3D) heterojunctions have enabled many solar cell devices with >25% power conversion efficiency, driven by advances in our understanding of the structural and photophysical properties of the heterojunctions and our ability to control these properties through organic cation configuration in 2D perovskites. In this feature article, we discuss a fundamental understanding of structural characteristics and the carrier dynamics in the 2D/3D heterojunctions and their impact factors. We further elaborate the design strategies for the molecular configuration of organic cations to achieve thorough management of these properties. Finally, recent advances in 2D/3D heterostructures in solar cells, light-emitting devices and photodetectors are highlighted, which translate fundamental understandings to device applications and also reveal the remaining challenges in ligand design for the next generation of stable devices. Future development prospects and related challenges are also provided, with wide perspectives and insightful thoughts.

Polyfluorinated Organic Diammonium Induced Lead Iodide Arrangement for Efficient Two-Step-Processed Perovskite Solar Cells

The inefficient conversion of lead iodide to perovskite has become one of the major challenges in further improving the performance of perovskite solar cells fabricated by the two-step method. Herein, the discontinuous lead iodide layer realized by introduction of a polyfluorinated organic diammonium salt, octafluoro-([1,1'-biphenyl]-4,4'-diyl)-dimethanaminium (OFPP) iodide which does not form low-dimensional perovskites, can enable the satisfactory conversion of lead iodide into perovskite, leading to meliorated crystallinity and enlarged grains in the OFPP modulated perovskite (OFPP-PVK) film. Combined with the effective defect passivation, the OFPP-PVK films show enhanced charge mobility and suppressed charge recombination. Accordingly, the OFPP-based perovskite solar cells exhibit a champion efficiency of 24.76 % with better device stability. Moreover, a superior efficiency of 21.04 % was achieved in a large-area perovskite module (100 cm2). Our work provides a unique insight into the function of organic diammonium additive in boosting photovoltaic performance.

Slow-Release Effect Assisted Crystallization for Sequential Deposition Realizes Efficient Inverted Perovskite Solar Cells

The two-step sequential deposition strategy has been widely recognized in promoting the research and application of perovskite solar cells, but the rapid reaction of organic salts with lead iodide inevitably affects the growth of perovskite crystals, accompanied by the generation of more defects. In this study, the regulation of crystal growth was achieved in a two-step deposition method by mixing 1-naphthylmethylammonium bromide (NMABr) with organic salts. The results show that the addition of NMABr effectively delays the aggregation and crystallization behavior of organic salts; thereby, the growth of the optimal crystal (001) orientation of perovskite is promoted. Based on this phenomenon of delaying the crystallization process of perovskite, the "slow-release effect assisted crystallization" is defined. Moreover, the incorporation of the Br element expands the band gap of perovskite and mitigates material defects as nonradiative recombination centers. Consequently, the power conversion efficiency (PCE) of the enhanced perovskite solar cells (PSCs) reaches 20.20%. It is noteworthy that the hydrophobic nature of the naphthalene moiety in NMABr can enhance the humidity resistance of PSCs, and the perovskite phase does not decompose for more than 3000 h (30-40% RH), enabling it to retain 90% of its initial efficiency even after exposure to a nitrogen environment for 1200 h.

Efficient and Stable Inverted Perovskite Solar Modules Enabled by Solid-Liquid Two-Step Film Formation

A considerable efficiency gap exists between large-area perovskite solar modules and small-area perovskite solar cells. The control of forming uniform and large-area film and perovskite crystallization is still the main obstacle restricting the efficiency of PSMs. In this work, we adopted a solid-liquid two-step film formation technique, which involved the evaporation of a lead iodide film and blade coating of an organic ammonium halide solution to prepare perovskite films. This method possesses the advantages of integrating vapor deposition and solution methods, which could apply to substrates with different roughness and avoid using toxic solvents to achieve a more uniform, large-area perovskite film. Furthermore, modification of the NiOx/perovskite buried interface and introduction of Urea additives were utilized to reduce interface recombination and regulate perovskite crystallization. As a result, a large-area perovskite film possessing larger grains, fewer pinholes, and reduced defects could be achieved. The inverted PSM with an active area of 61.56 cm2 (10 × 10 cm2 substrate) achieved a champion power conversion efficiency of 20.56% and significantly improved stability. This method suggests an innovative approach to resolving the uniformity issue associated with large-area film fabrication.

Single Crystal Seed Induced Epitaxial Growth Stabilizes α-FAPbI3 in Perovskite Solar Cells

FAPbI3 stands out as an ideal candidate for the photoabsorbing layer of perovskite solar cells (PSCs), showcasing outstanding photovoltaic properties. Nonetheless, stabilizing photoactive α-FAPbI3 remains a challenge due to the lower formation energy of the competitive photoinactive δ-phase. In this study, we employ tetraethylphosphonium lead tribromide (TEPPbBr3) single crystals as templates for the epitaxial growth of PbI2. The strategic use of TEPPbBr3 optimizes the evolution of intermediates and the crystallization kinetics of perovskites, leading to high-quality and phase-stable α-FAPbI3 films. The TEPPbBr3-modified perovskite exhibits optimized carrier dynamics, yielding a champion efficiency of 25.13% with a small voltage loss of 0.34 V. Furthermore, the target device maintains 90% of its initial PCE under maximum power point (MPP) tracking over 1000 h. This work establishes a promising pathway through single crystal seed based epitaxial growth for achieving satisfactory crystallization regulation and phase stabilization of α-FAPbI3 perovskites toward high-efficiency and stable PSCs.

2D BA2PbI4 Regulating PbI2 Crystallization to Induce Perovskite Growth for Efficient Solar Cells

Using seeds to control the crystallization of perovskite film is an effective strategy for achieving high-efficiency perovskite solar cells (PSCs). Owing to their excellent environmental stability brought by their long alkyl chain, n-butylammonium (BA) cations are widely used for fabricating efficient and stable PSCs. However, BA-based 2D perovskite is seldom been investigated as a seed. Here, BA2PbI4 is employed to regulate the crystallization of PbI2, acting as nucleation centers. As a result, porous PbI2 film with high crystallinity is obtained, which allows the realization of perovskite film with preferential crystal orientations of (001) and large grain size of over 2 µm. The corresponding PSC achieves a high power conversion efficiency (PCE) of 24.30% and exhibits satisfactory stability, retaining 91.70% of the initial PCE after 300 h of thermal aging at 85°C.

Dimensional Regulation from 1D/3D to 2D/3D of Perovskite Interfaces for Stable Inverted Perovskite Solar Cells

Constructing low-dimensional/three-dimensional (LD/3D) perovskite solar cells can improve efficiency and stability. However, the design and selection of LD perovskite capping materials are incredibly scarce for inverted perovskite solar cells (PSCs) because LD perovskite capping layers often favor hole extraction and impede electron extraction. Here, we develop a facile and effective strategy to modify the perovskite surface by passivating the surface defects and modulating surface electrical properties by incorporating morpholine hydriodide (MORI) and thiomorpholine hydriodide (SMORI) on the perovskite surface. Compared with the PI treatment that we previously developed, the one-dimensional (1D) perovskite capping layer derived from PI is transformed into a two-dimensional (2D) perovskite capping layer (with MORI or SMORI), achieving dimension regulation. It is shown that the 2D SMORI perovskite capping layer induces more robust surface passivation and stronger n-N homotype 2D/3D heterojunctions, achieving a p-i-n inverted solar cell with an efficiency of 24.55%, which retains 87.6% of its initial efficiency after 1500 h of operation at the maximum power point (MPP). Furthermore, 5 × 5 cm2 perovskite mini-modules are presented, achieving an active-area efficiency of 22.28%. In addition, the quantum well structure in the 2D perovskite capping layer increases the moisture resistance, suppresses ion migration, and improves PSCs' structural and environmental stability.

In Situ-Grown 2D Perovskite Based on π-Conjugated Aggregation-Induced Emission Organic Spacer Boosting the Efficiency and Stability of 2D-3D Heterostructured Perovskite Solar Cells

The two-dimensional-three-dimensional (2D-3D) heterostructured perovskite solar cells (PSCs) have drawn widespread interest, wherein the organic spacer plays a significant role in the photovoltaic performance. Herein, a novel π-conjugated organic spacer with the aggregation-induced emission (AIE) property, (Z)-2-([1,1'-biphenyl]-4-yl)-3-(5-(4-(3-aminopropoxy)phenyl)thiophen-2-yl)acrylonitrile (BPCSA-S), is designed and synthesized, which is successfully applied for the in situ construction of 2D-3D heterostructured PSCs via the two-step solution method. By virtue of the functional groups (i.e., cyano, thiophene, and amino) in BPCSA-S, the BPCSA-S organic spacer can trigger the in situ growth of 2D perovskites, which will serve as the template for the heteroepitaxial growth of 3D perovskites, thus obtaining a 2D-3D heterostructured film with high-quality and few defects. More pleasingly, benefiting from the AIE property and delocalized π-electrons in the π-conjugated BPCSA-S organic spacer, excellent photosensitization process and carrier transport can be achieved. Consequently, the resultant 2D-3D heterostructured PSCs yield a pleasing PCE of 22.07%, accompanied by mitigatory hysteresis, as well as enhanced stability. Our research shows a hopeful multifunctional organic spacer approach using the novel π-conjugated AIE organic spacer for high-performance PSCs.

Moisture-Resilient Perovskite Solar Cells for Enhanced Stability

With the rapid rise in device performance of perovskite solar cells (PSCs), overcoming instabilities under outdoor operating conditions has become the most crucial obstacle toward their commercialization. Among stressors such as light, heat, voltage bias, and moisture, the latter is arguably the most critical, as it can decompose metal-halide perovskite (MHP) photoactive absorbers instantly through its hygroscopic components (organic cations and metal halides). In addition, most charge transport layers (CTLs) commonly employed in PSCs also degrade in the presence of water. Furthermore, photovoltaic module fabrication encompasses several steps, such as laser processing, subcell interconnection, and encapsulation, during which the device layers are exposed to the ambient atmosphere. Therefore, as a first step toward long-term stable perovskite photovoltaics, it is vital to engineer device materials toward maximizing moisture resilience, which can be accomplished by passivating the bulk of the MHP film, introducing passivation interlayers at the top contact, exploiting hydrophobic CTLs, and encapsulating finished devices with hydrophobic barrier layers, without jeopardizing device performance. Here, existing strategies for enhancing the performance stability of PSCs are reviewed and pathways toward moisture-resilient commercial perovskite devices are formulated.

RbPbI3 Seed Embedding in PbI2 Substrate Tailors the Facet Orientation and Crystallization Kinetics of Perovskites

High power conversion efficiencies (PCEs) in perovskite solar cells (PSCs) have always been awe-inspiring, but perovskite films scalability is an exacting precondition for PSCs commercial deployment, generally unachievable through the antisolvent technique. On the contrary, in the two-step sequential method, the perovskite's uncontrolled crystallization and unnecessary PbI2 residue impede the device's performance. These two issues motivated to empower the PbI2 substrate with orthorhombic RbPbI3 crystal seeds, which act as grown nuclei and develop orientated perovskites lattice stacks, improving the perovskite films morphologically and reducing the PbI2 content in eventual perovskite films. Thence, achieving a PCE of 24.17% with suppressed voltage losses and an impressive life span of 1140 h in the open air.

Single-Crystal-Assisted In Situ Phase Reconstruction Enables Efficient and Stable 2D/3D Perovskite Solar Cells

Perovskite solar cells (PSCs) that incorporate both two-dimensional (2D) and three-dimensional (3D) phases possess the potential to combine the high stability of 2D PSCs with the superior efficiency of 3D PSCs. Here, we demonstrated in situ phase reconstruction of 2D/3D perovskites using a 2D perovskite single-crystal-assisted method. A gradient phase distribution of 2D RP perovskites was formed after spin-coating a solution of the 2D Ruddlesden-Popper (RP) perovskite single crystal, (DFP)2PbI4, onto the 3D perovskite surface, followed by thermal annealing. The resulting film exhibits much reduced trap density, increased carrier mobility, and superior water resistance. As a result, the optimized 2D/3D PSCs achieved a champion efficiency of 24.87% with a high open-circuit voltage (VOC) of 1.185 V. This performance surpasses the control 3D perovskite device, which achieved an efficiency of 22.43% and a VOC of 1.129 V. Importantly, the unencapsulated device demonstrates significantly enhanced operational stability, preserving over 97% of its original efficiency after continuous light irradiation for 1500 h. Moreover, the extrapolated T80 lifetimes surpass 5700 h. These findings pave the way for rational regulation of the gradient phase distribution at the interface between 2D and 3D perovskites by employing 2D RP perovskite crystals to achieve stable and efficient PSCs.

Crystal Growth Regulation of Ruddlesden-Popper Perovskites via Self-Assembly of Semiconductor Spacers for Efficient Solar Cells

The crystal growth and orientation of two-dimensional (2D) perovskite films significantly impact solar cell performance. Here, we incorporated robust quadrupole-quadrupole interactions to govern the crystal growth of 2D Ruddlesden-Popper (RP) perovskites. This was achieved through the development of two unique semiconductor spacers, namely PTMA and 5FPTMA, with different dipole moments. The ((5FPTMA)0.1 (PTMA)0.9 )2 MAn-1 Pbn I3n+1 (nominal n=5, 5F/PTMA-Pb) film shows a preferred vertical orientation, reduced grain boundaries, and released residual strain compared to (PTMA)2 MAn-1 Pbn I3n+1 (nominal n=5, PTMA-Pb), resulting in a decreased exciton binding energy and reduced electron-phonon coupling coefficients. In contrast to PTMA-Pb device with an efficiency of 15.66 %, the 5F/PTMA-Pb device achieved a champion efficiency of 18.56 %, making it among the best efficiency for 2D RP perovskite solar cells employing an MA-based semiconductor spacer. This work offers significant insights into comprehending the crystal growth process of 2D RP perovskite films through the utilization of quadrupole-quadrupole interactions between semiconductor spacers.

Orbital Interactions in 2D Dion-Jacobson Perovskites Using Oligothiophene-Based Semiconductor Spacers Enable Efficient Solar Cells

2D Dion-Jacobson (DJ) perovskites have emerged as promising photovoltaic materials, but the insulating organic spacer has hindered the efficient charge transport. Herein, we successfully synthesized a terthiophene-based semiconductor spacer, namely, 3ThDMA, for 2D DJ perovskite. An interesting finding is that the energy levels of 3ThDMA extensively overlap with the inorganic components and directly contribute to the band formation of (3ThDMA)PbI4, leading to enhanced charge transport across the organic spacer layers, whereas no such orbital interactions were found in (UDA)PbI4, a DJ perovskite based on 1,11-undecanediaminum (UDA). The devices based on (3ThDMA)MAn-1PbnI3n+1 (nominal n = 5) obtained a champion efficiency of 15.25%, which is a record efficiency for 2D DJ perovskite solar cells using long-conjugated spacers (conjugated rings ≥ 3) and a 22.60% efficiency for 3ThDMA-treated 3D PSCs. Our findings provide an important insight into understanding the orbital interactions in 2D DJ perovskite using an organic semiconductor spacer for efficient solar cells.

Bilayer 2D-3D Perovskite Heterostructures for Efficient and Stable Solar Cells

With a stacking-layered architecture, the bilayer two-dimensional-three-dimensional (2D-3D) perovskite heterostructure (PHS) not only eliminates surface defects but also protects the 3D perovskite matrix from external stimuli. However, these bilayer 2D-3D PHSs suffer from impaired interfacial charge carrier transport due to the relatively insulating 2D perovskite fragments with a random phase distribution. Over the past decade, substantial efforts have been devoted to pioneering molecular and structural designs of the 2D perovskite interlayers for improving their charge carrier mobility, which enables state-of-the-art perovskite solar cells with high power conversion efficiency and exceptional operational stability. Herein, this review offers a comprehensive and up-to-date overview on the recent progress of bilayer 2D-3D PHSs, encompassing advancements on spacer cation engineering, interfacial charge carrier modification, advanced deposition protocols, and characterization techniques. Then, the evolutionary trajectory of bilayer 2D-3D PHSs is outlined by summarizing its mainstream development trends, followed by a perspective discussion about its future research opportunities toward efficient and durable perovskite solar cells.

In Situ Formation of 2D Perovskite Seeding for Record-Efficiency Indoor Perovskite Photovoltaic Devices

With 40% efficiency under room light intensity, perovskite solar cells (PSCs) will be promising power supplies for low-light applications, particularly for Internet of Things (IoT) devices and indoor electronics, shall they become commercialized. Herein, β-alaninamide hydrochloride (AHC) is utilized to spontaneously form a layer of 2D perovskite nucleation seeds for improved film uniformity, crystallization quality, and solar cell performance. It is found that the AHC addition indeed improves film quality as demonstrated by better uniformity, lower trap density, smaller lattice stress, and, as a result, a 10-fold increase in charge carrier lifetime. Consequently, not only does the small-area (0.09 cm2 ) PSCs achieve a power conversion efficiency of 42.12%, the large-area cells (1.00 cm2 , and 2.56 cm2 ) attain efficiency as high as 40.93%, and 40.07% respectively. All of these are the highest efficiency values for indoor photovoltaic cells with similar sizes, and more importantly, they represent the smallest efficiency loss due to area scale-up. This work provides a new method to fabricate high-performance indoor PSCs (i-PSCs) for IoT devices with great potential in large-area printing technology.

Inhibition of Ion Migration for Highly Efficient and Stable Perovskite Solar Cells

In recent years, organic-inorganic halide perovskites are now emerging as the most attractive alternatives for next-generation photovoltaic devices, due to their excellent optoelectronic characteristics and low manufacturing cost. However, the resultant perovskite solar cells (PVSCs) are intrinsically unstable owing to ion migration, which severely impedes performance enhancement, even with device encapsulation. There is no doubt that the investigation of ion migration and the summarization of recent advances in inhibition strategies are necessary to develop "state-of-the-art" PVSCs with high intrinsic stability for accelerated commercialization. This review systematically elaborates on the generation and fundamental mechanisms of ion migration in PVSCs, the impact of ion migration on hysteresis, phase segregation, and operational stability, and the characterizations for ion migration in PVSCs. Then, many related works on the strategies for inhibiting ion migration toward highly efficient and stable PVSCs are summarized. Finally, the perspectives on the current obstacles and prospective strategies for inhibition of ion migration in PVSCs to boost operational stability and meet all of the requirements for commercialization success are summarized.

Selenophene-Based 2D Ruddlesden-Popper Perovskite Solar Cells with an Efficiency Exceeding 19

Two-dimensional (2D) Ruddlesden-Popper (RP) perovskites have emerged as attractive candidates for high-performance perovskite solar cells (PSCs) thanks to their superior environmental and structural stability. However, 2D RP PSCs exhibit larger exciton binding energy due to the dielectric mismatch between the organic and inorganic layers, resulting in poorer photovoltaic performance compared to their 3D analogs. Here, we developed a selenophene-based spacer, namely, 2-selenophenemethylammonium (SeMA), for stable and efficient 2D RP PSCs. The 2D perovskite film using methylammonium (MA) as the A-site cation (nominal n = 5) shows excellent film quality with large grain size and a preferred vertical orientation relative to the substrate. Furthermore, we have successfully demonstrated the effectiveness of a predeposition transport layer (PDTL) consisting of [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) in passivating surface defects of the perovskite film and inducing densification of the upper PCBM electron transport layer. This densification promotes efficient extraction and transport of electrons. The optimized PSCs based on 2D RP perovskite using MA as A-site cation (nominal n = 5) achieved a power conversion efficiency (PCE) of 17.25%, which was further boosted to 19.03% when using formamidinium (FA) as A-site cation. This represents a record PCE of 2D RP PSCs by using the selenophene-based spacer. Moreover, these 2D RP PSCs significantly improve thermal, moisture, and light stability. Our results provide significant implications for the synergistic strategy of developing selenophene-based spacers and device engineering methods for achieving highly efficient and stable 2D RP perovskite solar cells.

Magnetic Field-Assisted Interface Embedding Strategy to Construct 2D/3D Composite Structure for Stable Perovskite Solar Cells with Efficiency Over 24

Perovskite solar cells (PSCs) based on 2D/3D composite structure have shown enormous potential to combine high efficiency of 3D perovskite with high stability of 2D perovskite. However, there are still substantial non-radiative losses produced from trap states at grain boundaries or on the surface of conventional 2D/3D composite structure perovskite film, which limits device performance and stability. In this work, a multifunctional magnetic field-assisted interfacial embedding strategy is developed to construct 2D/3D composite structure. The composite structure not only improves crystallinity and passivates defects of perovskite layer, but also can efficiently promote vertical hole transport and provide lateral barrier effect. Meanwhile, the composite structure also forms a good surface and internal encapsulation of 3D perovskite to inhibit water diffusion. As a result, the multifunctional effect effectively improves open-circuit voltage and fill factor, reaching maximum values of 1.246 V and 81.36%, respectively, and finally achieves power conversion efficiency (PCE) of 24.21%. The unencapsulated devices also demonstrate highly improved long-term stability and humidity stability. Furthermore, an augmented performance of 21.23% is achieved, which is the highest PCE of flexible device based on 2D/3D composite perovskite films coupled with the best mechanical stability due to the 2D/3D alternating structure.

Target Therapy for Buried Interface Enables Stable Perovskite Solar Cells with 25.05% Efficiency

The buried interface in perovskite solar cells (PSCs) is pivotal for achieving high efficiency and stability. However, it is challenging to study and optimize the buried interface due to its non-exposed feature. Here, a facile and effective strategy is developed to modify the SnO2 /perovskite buried interface by passivating the buried defects in perovskite and modulating carrier dynamics via incorporating formamidine oxalate (FOA) in SnO2 nanoparticles. Both formamidinium and oxalate ions show a longitudinal gradient distribution in the SnO2 layer, mainly accumulating at the SnO2 /perovskite buried interface, which enables high-quality upper perovskite films, minimized defects, superior interface contacts, and matched energy levels between perovskite and SnO2 . Significantly, FOA can simultaneously reduce the oxygen vacancies and tin interstitial defects on the SnO2 surface and the FA+ /Pb2+ associated defects at the perovskite buried interface. Consequently, the FOA treatment significantly improves the efficiency of the PSCs from 22.40% to 25.05% and their storage- and photo-stability. This method provides an effective target therapy of buried interface in PSCs to achieve very high efficiency and stability.

Additive Conformational Engineering To Improve the PbI2 Framework for Efficient and Stable Perovskite Solar Cells

The PbI2 framework is critical for two-step fabricated perovskite solar cells. This study investigates the effects of introducing two functional urea-based molecules, biuret (BU) and dithiobiuret (DTBU), into the PbI2 precursor solution on the absorber layer and overall device performance. BU, which contains C═O, enhanced device performance and stability, whereas DTBU, which contains C═S, had negative effects. Research analysis revealed the differences in the spatial structures of the two urea-based molecules. The introduction of symmetrical BU molecules facilitated the crystallization of PbI2, whereas the introduction of DTBU with a twisted molecular structure led to inferior crystallization performance of PbI2. The perovskite thin film, obtained by introducing BU into the PbI2 precursor solution, demonstrated superior performance, characterized by a decreased defect density and an extended carrier lifetime. The device performance and stability were enhanced, resulting in higher open-circuit voltage and fill factor. The highest achieved power conversion efficiency was 23.50%. After 1300 h of storage under unpackaged conditions at 30-40% humidity, the devices maintained 93% of their initial efficiency. Conversely, the devices prepared with DTBU doping exhibited inferior performance and stability, displaying power conversion efficiency below 10% and faster degradation under the same humidity conditions.

Highly Efficient and Stable Perovskite Solar Cells: Competitive Crystallization Strategy and Synergistic Passivation

Defects of perovskite (PVK) films are one of the main obstacles to achieving high-performance perovskite solar cells (PSCs). Here, the authors fabricated highly efficient and stable PSCs by introducing prolinamide (ProA) into the PbI2 precursor solution, which improves the performance of PSCs by the competitive crystallization and efficient defect passivation of perovskite. The theoretical and experimental results indicate that ProA forms an adduct with PbI2 , competes with free I- to coordinate with Pb2+ , leads to the increase of the energy barrier of crystallization, and slows down the crystallization rate. Furthermore, the dual-site synergistic passivation of ProA is revealed by density functional theory (DFT) calculations and experimental results. ProA effectively reduces non-radiative recombination in the resultant films to improve the photovoltaic performance of PSCs. Notably, ProA-assisted PSCs achieve 24.61% power conversion efficiency (PCE) for the champion device and the stability of PSCs devices under ambient and thermal environments is improved.

Stabilization of photoactive phases for perovskite photovoltaics

Interest in photovoltaics (PVs) based on Earth-abundant halide perovskites has increased markedly in recent years owing to the remarkable properties of these materials and their suitability for energy-efficient and scalable solution processing. Formamidinium lead triiodide (FAPbI₃)-rich perovskite absorbers have emerged as the frontrunners for commercialization, but commercial success is reliant on the stability meeting the highest industrial standards and the photoactive FAPbI₃ phase suffers from instabilities that lead to degradation - an effect that is accelerated under working conditions. Here, we critically assess the current understanding of these phase instabilities and summarize the approaches for stabilizing the desired phases, covering aspects from fundamental research to device engineering. We subsequently analyse the remaining challenges for state-of-the-art perovskite PVs and demonstrate the opportunities to enhance phase stability with ongoing materials discovery and in operando analysis. Finally, we propose future directions towards upscaling perovskite modules, multijunction PVs and other potential applications.

Ultralong Carrier Lifetime Exceeding 20 µs in Lead Halide Perovskite Film Enable Efficient Solar Cells

The carrier lifetime is one of the key parameters for perovskite solar cells (PSCs). However, it is still a great challenge to achieve long carrier lifetimes in perovskite films that are comparable with perovskite crystals owning to the large trap density resulting from the unavoidable defects in grain boundaries and surfaces. Here, by regulating the electronic structure with the developed 2-thiopheneformamidinium bromide (ThFABr) combined with the unique film structure of 2D perovskite layer caped 2D/3D polycrystalline perovskite film, an ultralong carrier lifetime exceeding 20 µs and carrier diffusion lengths longer than 6.5 µm are achieved. These excellent properties enable the ThFA-based devices to yield a champion efficiency of 24.69% with a minimum VOC loss of 0.33 V. The unencapsulated device retains ≈95% of its initial efficiency after 1180 h by max power point (MPP) tracking under continuous light illumination. This work provides important implications for structured 2D/(2D/3D) perovskite films combined with unique FA-based spacers to achieve ultralong carrier lifetime for high-performance PSCs and other optoelectronic applications.

Improving Crystallization and Stability of Perovskite Solar Cells Using a Low-Temperature Treated A-Site Cation Solution in the Sequential Deposition

The two-step sequential deposition is a commonly used method by researchers for fabricating perovskite solar cells (PSCs) due to its reproducibility and tolerant preparation conditions. However, the less-than-favorable diffusive processes in the preparation process often result in subpar crystalline quality in the perovskite films. In this study, we employed a simple strategy to regulate the crystallization process by lowering the temperature of the organic-cation precursor solutions. By doing so, we minimized interdiffusion processes between the organic cations and pre-deposited lead iodide (PbI2) film under poor crystallization conditions. This allowed for a homogenous perovskite film with improved crystalline orientation when transferred to appropriate environmental conditions for annealing. As a result, a boosted power conversion efficiency (PCE) was achieved in PSCs tested for 0.1 cm2 and 1 cm2, with the former exhibiting a PCE of 24.10% and the latter of 21.56%, compared to control PSCs, which showed a PCE of 22.65% and 20.69%, respectively. Additionally, the strategy increased device stability, with the cells holding 95.8% and 89.4% of the initial efficiency even after 7000 h of aging under nitrogen or 20-30% relative humidity and 25 °C. This study highlights a promising low-temperature-treated (LT-treated) strategy compatible with other PSCs fabrication techniques, adding a new possibility for temperature regulation during crystallization.

Facet Engineering: A Promising Pathway toward Highly Efficient and Stable Perovskite Photovoltaics

Perovskite solar cells are considered to be important candidates for future energy applications. The facet orientation causes anisotropy in the photoelectric and chemical properties of the surface of perovskite films and therefore might affect the photovoltaic properties and stability of the devices. Facet engineering has attracted increasing attention only recently in the perovskite solar cell community, and related deep investigation is rather rare. To date, it is still difficult to precisely regulate and directly observe perovskite films with specific crystal facets due to the limitations of solution methods and characterization technology. Consequently, the link between facet orientation and photovoltaic performance of perovskite solar cells is still controversial. Herein, we highlight the latest progress in the means of direct characterization and regulation of crystal facets and briefly analyze the existing issues and future perspectives of facet engineering in perovskite photovoltaics.

1D Choline-PbI3-Based Heterostructure Boosts Efficiency and Stability of CsPbI3 Perovskite Solar Cells

Defects in perovskite are key factors in limiting the photovoltaic performance and stability of perovskite solar cells (PSCs). Generally, choline halide (ChX) can effectively passivate defects by binding with charged point defects of perovskite. However, we verified that ChI can react with CsPbI3 to form a novel crystal phase of one-dimensional (1D) ChPbI3, which constructs 1D/3D heterostructure with 3D CsPbI3, passivating the defects of CsPbI3 more effectively and then resulting in significantly improved photoluminescence lifetime from 20.2 ns to 49.4 ns. Moreover, the outstanding chemical inertness of 1D ChPbI3 and the repair of undesired δ-CsPbI3 deficiency during its formation process can significantly enhance the stability of CsPbI3 film. Benefiting from 1D/3D heterostructure, CsPbI3 carbon-based PSCs (C-PSCs) delivered a champion efficiency of 18.05% and a new certified record of 17.8% in hole transport material (HTM)-free inorganic C-PSCs.

Multifunctional Molecule Assists Passivate Method to Simultaneously Improve the Efficiency and Stability of Perovskite Solar Cells

The power conversion efficiency (PCE) of perovskite solar cells (PSCs) has been greatly improved recently. However, in organic-inorganic polycrystalline perovskite films many defects inevitably exist, which limits the PCE and stability of PSCs. Herein, a small organic molecule 2-chlorothiazole-4-carboxylic acid (SN) is spin coated on a perovskite film to enhance the performance of PSCs. We find that the multifunctional molecule SN reacts with under-coordinated Pb²⁺ ions and I^- vacancies because of the presence of the sulfur and nitrogen donor atoms, and the -COOH groups, which are conducive to suppressing charge recombination and passivating defects. Even more, the introduction of the SN layer can effectively adjust the energy level alignment, which is conducive to the separation and extraction of charge carriers in PSCs. Therefore, devices with SN modification show a champion PCE of 22.55 %. Besides, PSCs with SN show impressive stability, retaining 96 % of its initial PCE after storage in ambient air for 500 h.

Highly Efficient and Stable FA-Based Quasi-2D Ruddlesden-Popper Perovskite Solar Cells by the Incorporation of β-Fluorophenylethanamine Cations

2D Ruddlesden-Popper (2D RP) perovskite, with attractive environmental and structural stability, has shown great application in perovskite solar cells (PSCs). However, the relatively inferior photovoltaic efficiencies of 2D PSCs limit their further application. To address this issue, β-​fluorophenylethanamine (β-​FPEA) as a novel spacer cation is designed and employed to develop stable and efficient quasi-2D RP PSCs. The strong dipole moment of the β-​FPEA enhances the interactions between the cations and [PbI₆ ]^4- octahedra, thus improving the charge dissociation of quasi-2D RP perovskite. Additionally, the introduction of the β-​FPEA cation optimizes the energy level alignment, improves the crystallinity, stabilizes both the mixed phase and a-FAPbI₃ phase of the quasi-2D RP perovskite film, prolongs the carrier diffusion length, increases the carrier lifetime and decreases the trap density. By incorporating the β-​FPEA, the quasi-2D RP PSCs exhibit a power conversion efficiency (PCE) of 16.77% (vs phenylethylammonium (PEA)-based quasi-2D RP PSCs of 12.81%) on PEDOT:PSS substrate and achieve a champion PCE of 19.11% on the PTAA substrate. It is worth noting that the unencapsulated β-​FPEA-based quasi-2D RP PSCs exhibit considerably improved thermal and moisture stability. These findings provide an effective strategy for developing novel spacer cations for high-performance 2D RP PSCs.

Intermediate Phase Engineering with 2,2-Azodi(2-Methylbutyronitrile) for Efficient and Stable Perovskite Solar Cells

Sequential deposition has been widely employed to modulate the crystallization of perovskite solar cells because it can avoid the formation of nucleation centers and even initial crystallization in the precursor solution. However, challenges remain in overcoming the incomplete and random transformation of PbI₂ films with organic ammonium salts. Herein, a unique intermediate phase engineering strategy has been developed by simultaneously introducing 2,2-azodi(2-methylbutyronitrile) (AMBN) to both PbI₂ and ammonium salt solutions to regulate perovskite crystallization. AMBN not only coordinates with PbI₂ to form a favorably mesoporous PbI₂ film due to the coordination between Pb²⁺ and the cyano group (C≡N), but also suppresses the vigorous activity of FA⁺ ions by interacting with FAI, leading to the full PbI₂ transformation with the preferred orientation. Therefore, perovskites with favorable facet orientations are obtained, and the defects are largely suppressed owing to the passivation of uncoordinated Pb²⁺ and FA⁺ . As a result, a champion power conversion efficiency over 25% with a stabilized efficiency of 24.8% is achieved. Moreover, the device exhibits an improved operational stability, retaining 96% of initial power conversion efficiency under 1000 h continuous white-light illumination with an intensity of 100 mW cm^-2 at ≈55 °C in N₂ atmosphere.

Dual Optimization of Bulk and Interface via the Synergistic Effect of Ligand Anchoring and Hole Transport Dopant Enables 23.28% Efficiency Inverted Perovskite Solar Cells

The crystalline morphology of perovskite film plays a key role in determining the stability and performance of perovskite solar cells (PSCs). In addition, the work function and conductivity of hole transport layer (HTL) have a great influence on the effciency of PSCs. Here, we develop a synergistic doping strategy to fabricate high-performance inverted PSCs, doping a functional nanographene (C₇₈-AHM) into the poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine (PTAA) HTL, thus forming an HTL with higher conductivity, lower roughness, and frontier energy levels matching the perovskite absorber work function. On this basis, thiosemicarbazide (TSC) was doped into the precursor solution of perovskite as the grain and interface modifier to further improve the crystalline morphology of perovskite film. Compared with the current single passivation method, this codoping strategy can simultaneously reduce the surface and bulk defects of perovskite film and reduce the interface energy barrier. Eventually, high-quality TSC-doped perovskite films based on C₇₈-AHM-doped PTAA HTL are obtained with over 2 μm sized grains, pinhole-free, and improved crystallinity. As a result, this synergistic doping strategy increases the efficiency of the device from 20.27% to 23.28%. Furthermore, the environmental and thermal stabilities of the devices are significantly improved. Therefore, this work provides a simple way for the preparation of other efficient optoelectronic devices.

Manipulating the Formation of 2D/3D Heterostructure in Stable High-Performance Printable CsPbI3 Perovskite Solar Cells

Manipulating the formation process of the 2D/3D perovskite heterostructure, including its nucleation/growth dynamics and phase transition pathway, plays a critical role in controlling the charge transport between 2D and 3D crystals, and consequently, the scalable fabrication of efficient and stable perovskite solar cells. Herein, the structural evolution and phase transition pathways of the ligand-dependent 2D perovskite atop the 3D surface are revealed using time-resolved X-ray scattering. The results show that the ligand size and shape have a critical influence on the final 2D structure. In particular, ligands with smaller sizes and more reactive sites tend to form the n = 1 phase. Increasing the ligand size and decreasing the reactive sites promote the transformation from 3D to n = 3 and n < 3 phases. These findings are useful for the rational design of the phase distribution in 2D perovskites to balance the charge transport and stability of the perovskite films. Finally, solar cells based on ambient-printed CsPbI₃ with n-butylammonium iodide treatment achieve an improved efficiency of 20.33%, which is the highest reported value for printed inorganic perovskite solar cells.

Overcoming C60-induced interfacial recombination in inverted perovskite solar cells by electron-transporting carborane

Inverted perovskite solar cells still suffer from significant non-radiative recombination losses at the perovskite surface and across the perovskite/C₆₀ interface, limiting the future development of perovskite-based single- and multi-junction photovoltaics. Therefore, more effective inter- or transport layers are urgently required. To tackle these recombination losses, we introduce ortho-carborane as an interlayer material that has a spherical molecular structure and a three-dimensional aromaticity. Based on a variety of experimental techniques, we show that ortho-carborane decorated with phenylamino groups effectively passivates the perovskite surface and essentially eliminates the non-radiative recombination loss across the perovskite/C₆₀ interface with high thermal stability. We further demonstrate the potential of carborane as an electron transport material, facilitating electron extraction while blocking holes from the interface. The resulting inverted perovskite solar cells deliver a power conversion efficiency of over 23% with a low non-radiative voltage loss of 110 mV, and retain >97% of the initial efficiency after 400 h of maximum power point tracking. Overall, the designed carborane based interlayer simultaneously enables passivation, electron-transport and hole-blocking and paves the way toward more efficient and stable perovskite solar cells.

Bottom-Up Templated and Oriented Crystallization for Inverted Triple-Cation Perovskite Solar Cells with Stabilized Nickel-Oxide Interface

Inverted-structure perovskite solar cells (PSCs) are known for their superior device stability. However, based on nickel-oxide (NiO_x ) substrate, disordered crystallization and bottom interface instability of perovskite film are still the main factors that compromise the power conversion efficiency (PCE) of PSCs. Here, 2D perovskite of thiomorpholine 1,1-dioxide lead iodide (Td₂ PbI₄ ) is introduced as a template to prepare 3D perovskite thin film with high crystal orientation and large grain size via a bottom-up growth method. By adding TdCl to the precursor solution, pre-crystallized 2D Td₂ PbI₄ seeds can accumulate at the bottom interface, lowering the barrier of nucleation, and templating the growth of 3D perovskite films with improved (100) orientation and reduced defects during crystallization. In addition, 2D Td₂ PbI₄ at the bottom interface also hinders the interfacial redox reaction and reduces the hole extraction barrier on the buried interface. Based on this, the Td-0.5 PSC achieves a PCE of 22.09% and an open-circuit voltage of 1.16 V. Moreover, Td-0.5 PSCs show extremely high stability, which retains 84% of its initial PCE after 500 h of continuous illumination under maximum power point operating conditions in N₂ atmosphere. This work paves the way for performance improvement of inverted PSCs on NiO_x substrate.

Efficient and Stable 3D/2D Perovskite Solar Cells through Vertical Heterostructures with (BA)4 AgBiBr8 Nanosheets

Perovskite solar cells (PVSCs) have drawn great attention due to their high processability and superior photovoltaic properties. However, their further development is often hindered by severe nonradiative recombination at interfaces that decreases power conversion efficiency (PCE). To this end, a facile strategy to construct a 3D/2D vertical heterostructure to reduce the energy loss in PVSCs is developed. The heterostructure is contrived through the van der Waals integration of 2D perovskite ((BA)₄ AgBiBr₈ ) nanosheets onto the surface of 3D-FAPbI₃ -based perovskites. The large bandgap of (BA)₄ AgBiBr₈ enables the formation of type-I heterojunction with 3D-FAPbI₃ -based perovskites, which serves as a barrier to suppress the trap-assisted recombination at the interface. As a result, a satisfying PCE of 24.48% is achieved with an improved open-circuit voltage (V_OC ) from 1.13 to 1.17 V. Moreover, the 2D perovskite nanosheets can effectively mitigate the iodide ion diffusion from perovskite to the metal electrode, hence enhancing the device stability. 3D/2D architectured devices retain ≈90% of their initial PCE under continuous illumination or heating after 1000 h, which are superior to 3D-based devices. This work provides an effective and controllable strategy to construct 3D/2D vertical heterostructure to simultaneously boost the efficiency and stability of PVSCs.

Novel PHA Organic Spacer Increases Interlayer Interactions for High Efficiency in 2D Ruddlesden-Popper CsPbI3 Solar Cells

The two-dimensional (2D) Ruddlesden-Popper (RP) CsPbI₃ with hydrophobic organic spacers can significantly improve the environmental and phase stability of photovoltaic devices by suppressing ion migration and inducing steric hindrance. However, due to the multiple-quantum-well structure, these spacer cations lead to weak interactions in 2D RP CsPbI₃, which seriously affect the carrier transport. Here, a novel N-H-group-rich phenylhydrazine spacer, namely, PHA, was developed for 2D RP CsPbI₃ perovskite solar cells (PSCs). A series of characterizations confirm that the 2D perovskites using PHA spacers enhanced the N-H···I hydrogen-bonding interaction between the organic spacer cations and the [PbI₆]^4- inorganic layer and accelerated the crystallization rate of the perovskite film, which was beneficial to the preparation of high-quality films with preferred vertical orientation, large grain size, and dense morphology. Meanwhile, the trap state density of the as-prepared 2D RP perovskite films is significantly reduced to enable efficient charge carrier transport. As a result, the (PHA)₂Cs₄Pb₅I₁₆ PSCs achieved a performance of 16.23% with good environmental stability. This work provides a simple organic spacer selection scheme to realize interaction optimization in 2D RP CsPbI₃ to develop efficient and stable PSCs.

Surface Re-Engineering of Perovskites with Buckybowls to Boost the Inverted-Type Photovoltaics

Despite their multifaceted advantages, inverted perovskite solar cells (PSCs) still suffer from lower power conversion efficiencies (PCEs) than their regular counterparts, which is largely due to recombination energy losses (E_loss) that arise from the chemical, physical, and energy level mismatches, especially at the interfaces between perovskites and fullerene electron transport layers (ETLs). To address this problem, we herein introduce an aminium iodide derivative of a buckybowl (aminocorannulene) that is molecularly layered at the perovskite-ETL interface. Strikingly, besides passivating the PbI₂-rich perovskite surface, the aminocorannulene enforces a vertical dipole and enhances the surface n-type character that is more compatible with the ETL, thus boosting the electron extraction and transport dynamics and suppressing interfacial E_loss. As a result, the champion PSC achieves an excellent PCE of over 22%, which is superior compared to that of the control device (∼20%). Furthermore, the device stability is significantly enhanced, owing to a lock-and-key-like grip on the mobile iodides by the buckybowls and the resultant increase of the interfacial ion-migration barrier. This work highlights the potential of buckybowls for the multifunctional surface engineering of perovskite toward high-performance and stable PSCs.