Recent Advances in Single‐Junction Organic Solar Cells

Accomplishing High-Performance Organic Solar Sub-Modules (≈55 cm2) with >16% Efficiency by Controlling the Aggregation of an Engineered Non-Fullerene Acceptor

The fabrication of environmentally benign, solvent-processed, efficient, organic photovoltaic sub-modules remains challenging due to the rapid aggregation of the current high performance non-fullerene acceptors (NFAs). In this regard, design of new NFAs capable of achieving optimal aggregation in large-area organic photovoltaic modules has not been realized. Here, an NFA named BTA-HD-Rh is synthesized with longer (hexyl-decyl) side chains that exhibit good solubility and optimal aggregation. Interestingly, integrating a minute amount of new NFA (BTA-HD-Rh) into the PM6:L8-BO system enables the improved solubility in halogen-free solvents (o-xylene:carbon disulfide (O-XY:CS2)) with controlled aggregation is found. Then solar sub-modules are fabricated at ambient condition (temperature at 25 ± 3 °C and humidity: 30-45%). Ultimately, the champion 55 cm2 sub-modules achieve exciting efficiency of >16% in O-XY:CS2 solvents, which is the highest PCE reported for sub-modules. Notably, the highest efficiency of BTA-HD-Rh doped PM6:L8-BO is very well correlated with high miscibility with low Flory-Huggins parameter (0.372), well-defined nanoscale morphology, and high charge transport. This study demonstrates that a careful choice of side chain engineering for an NFA offers fascinating features that control the overall aggregation of active layer, which results in superior sub-module performance with environmental-friendly solvents.

Dual Function of the Third Component in Ternary Organic Solar Cells: Broaden the Spectrum and Optimize the Morphology

Ternary organic solar cells (T-OSCs) have attracted significant attention as high-performance devices. In recent years, T-OSCs have achieved remarkable progress with power conversion efficiency (PCE) exceeding 19%. However, the introduction of the third component complicates the intermolecular interaction compared to the binary blend, resulting in poor controllability of active layer and limiting performance improvement. To address these issues, dual-functional third components have been developed that not only broaden the spectral range but also optimize morphology. In this review, the effect of the third component on expanding the absorption range of T-OSCs is first discussed. Second, the extra functions of the third component are introduced, including adjusting the crystallinity and molecular stack in active layer, regulating phase separation and purity, altering molecular orientation of the donor or acceptor. Finally, a summary of the current research progress is provided, followed by a discussion of future research directions.

Recent progress and prospects of dimer and multimer acceptors for efficient and stable polymer solar cells

High power conversion efficiency (PCE) and long-term stability are essential prerequisites for the commercialization of polymer solar cells (PSCs). Small-molecule acceptors (SMAs) are core materials that have led to recent, rapid increases in the PCEs of the PSCs. However, a critical limitation of the resulting PSCs is their poor long-term stability. Blend morphology degradation from rapid diffusion of SMAs with low glass transition temperatures (Tgs) is considered the main cause of the poor long-term stability of the PSCs. The recent emergence of oligomerized SMAs (OSMAs), composed of two or more repeating SMA units (i.e., dimerized and trimerized SMAs), has shown great promise in overcoming these challenges. This innovation in material design has enabled OSMA-based PSCs to reach impressive PCEs near 19% and exceptional long-term stability. In this review, we summarize the evolution of OSMAs, including their research background and recent progress in molecular design. In particular, we discuss the mechanisms for high PCE and stability of OSMA-based PSCs and suggest useful design guidelines for high-performance OSMAs. Furthermore, we reflect on the existing hurdles and future directions for OSMA materials towards achieving commercially viable PSCs with high PCEs and operational stabilities.

Chalcogen Atoms Regulate the Organic Solar Cell Performance of B-N-Based Polymer Donors

Donor polymers play a key role in the development of organic solar cells (OSCs). B-N-based polymer donors, as new types of materials, have attracted a lot of attention due to their special characteristics, such as high E(T1), small ΔEST, and easy synthesis, and they can be processed with real green solvents. However, the relationship between the chemical structure and device performance has not been systematically studied. Herein, chalcogen atoms that regulate the OSCs performance of B-N-based polymer donors were systematically studied. Fortunately, the substitution of a halogen atom did not affect the high E(T1) and small ΔEST character of the B-N-based polymer. The absorption and energy levels of the polymer were systematically regulated by O, S, and Se atom substitution. The PBNT-TAZ:Y6-BO-based OSCs device demonstrated a high power conversion efficiency of 15.36%. Moreover, the layer-by-layer method was applied to further optimize the device performance, and the PBNT-TAZ/Y6-BO-based OSCs device yielded a PCE of 16.34%. Consequently, we have systematically demonstrated how chalcogen atoms modulated the electronic properties of B-N-based polymers. Detailed and systematic structure-performance relationships are important for the development of next-generation B-N-based materials.

Halogenated 9H-Indeno[1,2-b]Pyrazine-2,3-Dicarbonitrile End Groups Based Asymmetric Non-Fullerene Acceptors for Green Solvent-Processable, Additive-Free, and Stable Organic Solar Cells

Non-fullerene acceptors (NFAs) significantly enhance photovoltaic performance in organic solar cells (OSCs) using halogenated solvents and additives. However, these solvents are environmentally detrimental and unsuitable for industrial-scale production, and the issue of OSCs' poor long-term stability persists. This report introduces eight asymmetric NFAs (IPCnF-BBO-IC2F, IPCnF-BBO-IC2Cl, IPCnCl-BBO-IC2F, and IPCnCl-BBO-IC2Cl, where n = 1 and 2). These NFAs comprise a 12,13-bis(2-butyloctyl)-3,9-diundecyl-12,13-dihydro-[1,2,5]thiadiazolo[3,4-e]thieno[2'',3'':4',5']thieno[2',3':4,5]pyrrolo[3,2-g]thieno[2',3':4,5]thieno-[3,2-b]indole (BBO) core. One end of the core attaches to a mono- or di-halogenated 9H-indeno[1,2-b]pyrazine-2,3-dicarbonitrile (IPC) end group (IPC1F, IPC1Cl, IPC2F, or IPC2Cl), while the other end connects to a 2-(5,6-dihalo-3-oxo-2,3-dihydro-1H-inden-1-ylidene)malononitrile (IC) end group (IC2F or IC2Cl). The optical and electronic properties of these NFAs can be finely tuned by controlling the number of halogen atoms. Crucially, these NFAs demonstrate excellent compatibility with PM6 even in o-xylene, facilitating the production of additive-free OSCs. The di-halogenated IPC-based NFAs outperform their mono-halogenated counterparts in photovoltaic performance within OSCs. Remarkably, the di-halogenated IPC-based NFAs maintain 94‒98% of their initial PCEs over 2000 h in air without encapsulation, indicating superior long-term device stability. These findings imply that the integration of di-halogenated IPCs in asymmetric NFA design offers a promising route to efficient, stable OSCs manufactured through environmentally friendly processes.

A Three-Dimensional Non-Fullerene Acceptor with Contorted Hexabenzocoronene and Perylenediimide for Organic Solar Cells

Although fullerene derivatives such as [6,6]-phenyl-C61/C71-butyric acid methyl ester (PC61BM/PC71BM) have dominated the the photoactive acceptor materials in bulk heterojunction organic solar cells (OSCs) for decades, they have several drawbacks such as weak absorption, limited structural tunability, prone to aggregation, and high costs of production. Constructing non-fullerene small molecules with three-dimensional (3D) molecular geometry is one of the strategies to replace fullerenes in OSCs. In this study, a 3D molecule, contorted hexa-cata-hexabenzocoronene tetra perylenediimide (HBC-4-PDI), was designed and synthesized. HBC-4-PDI shows a wide and strong light absorption in the whole UV-vis region as well as suitable energy levels as an acceptor for OSCs. More importantly, the 3D construction effectively reduced the self-aggregation of c-HBC, leading to an appropriate scale phase separation of the blend film morphology in OSCs. A preliminary power conversion efficiency of 2.70 % with a champion open-circuit voltage of 1.06 V was obtained in OSCs with HBC-4-PDI as the acceptor, which was the highest among the previously reported OSCs based on c-HBC derivatives. The results indicated that HBC-4-PDI may serve as a good non-fullerene acceptor for OSCs.

High-Efficiency Ternary Polymer Solar Cells with a Gradient-Blended Structure Fabricated by Sequential Deposition

Acquiring the ideal blend morphology of the active layer to optimize charge separation and collection is a constant goal of polymer solar cells (PSCs). In this paper, the ternary strategy and the sequential deposition process were combined to make sufficient use of the solar spectrum, optimize the energy-level structure, regulate the vertical phase separation morphology, and ultimately enhance the power conversion efficiency (PCE) and stability of the PSCs. Specifically, the donor and acceptor illustrated a gradient-blended distribution in the sequential deposition-processed films, thus resulting in facilitated carrier characteristics in the gradient-blended devices. Consequently, the PSCs based on D18-Cl/Y6:ZY-4Cl have achieved a device efficiency of over 18% with the synergetic improvement of open-circuit voltage (VOC), short-circuit current density (JSC), and fill factor (FF). Therefore, this work reveals a facile approach to fabricating PSCs with improved performance and stability.

Chemisorption-Induced Robust and Homogeneous Tungsten Disulfide Interlayer Enables Stable PEDOT-Free Organic Solar Cells with Over 19% Efficiency

Construction of a high-quality charge transport layer (CTL) with intimate contact with the substrate via tailored interface engineering is crucial to increase the overall charge transfer kinetics and stability for a bulk-heterojunction (BHJ) organic solar cell (OSC). Here, we demonstrate a surface chemistry strategy to achieve a homogeneous composite hole transport layer (C-HTL) with robust substrate contact by self-assembling two-dimensional tungsten disulfide (WS2) nanosheets on a thin molybdenum oxide (MoO3) film-evaporated indium tin oxide (ITO) substrate. It is found that over such a well-defined C-HTL, WS2 is homogeneously tethered on the ITO/MoO3 substrate stemming from the strong electronic coupling interaction between the building blocks, which enables a favorable interfacial configuration in terms of uniformity. As a result, the D18:L8-BO-based OSC with C-HTL exhibits a power conversion efficiency (PCE) of 19.23%, an 11% improvement over the WS2-based control device, and the highest efficiency among single-junction PEDOT-free binary BHJ OSCs.

Experimental and theoretical study to control the heavy metals in solid waste and sludge during pyrolysis using modified expanded vermiculite

Na+/K+/Mg2+/Ca2+ expansion-modified vermiculite and calcination expansion (700 °C, 800 °C and 900 °C)-modified vermiculite (700-Mg-V, 800-Mg-V and 900-Mg-V) were prepared as additives to control the emission of five heavy metals (Zn, Cr, Cu, Pb, and Cd) during the pyrolysis of municipal sewage sludge, paper mill sludge, municipal domestic waste, and aged refuse. Mg2+-Modified vermiculite obtained via thermally activated calcination at 800 °C retained 65% of heavy metals from all raw materials at 450 °C. Zn, Cr, and Cu retained nearly 90%. Although modified vermiculite could reduce the ecological risk, Cd had an ecological risk level higher than Zn, Cr, Cu, and Pb. The fine textural properties, laminated morphology, and expansion capacity of modified vermiculite were positively correlated with its retention of heavy metals. Heavy metals interacted with the (002) surface of vermiculite, and the reactions were mainly concentrated near the 17-O and surrounding atoms. The heavy-metal monomers were less capable of binding to the (002) surface of vermiculite than the oxides and chlorides of heavy metals. The effect of heavy-metal oxides and chlorides binding to the (002) surface of vermiculite was related to heavy metals.

Effect of Number and Position of Chlorine Atoms on the Photovoltaic Performance of Asymmetric Nonfullerene Acceptors

It has been well proved that the introduction of halogen can effectively modify the optoelectronic properties of classic symmetric nonfullerene acceptors (NFAs). However, the relevant studies for asymmetric NFAs are limited, especially the effect of halogen substitution number and position on the photovoltaic performance is not clear. In this work, four asymmetric NFAs with A-D-A1-A2 structure are developed by tuning the number and position of chlorine atoms on the 1,1-dicyanomethylene-3-indanone end groups, namely, A303, A304, A305, and A306. The related NFAs show progressively deeper energy levels and red-shifted absorption spectra as the degree of chlorination increases. The PM6:A306-constructed organic solar cells (OSCs) give a champion power conversion efficiency (PCE) of 13.03%. This is mainly ascribed to the most efficient exciton dissociation and collection, suppressed charge recombination, and optimal morphology. Moreover, by alternating the substitution position, the PM6:A305-based device yielded a higher PCE of 12.53% than that of PM6:A304 (12.05%). This work offers fresh insights into establishing excellent asymmetric NFAs for OSCs.

Synergistic effect of interface and defect engineering of MoC/MoO2 nano dot encapsulated N-doped carbon nanoflowers for highly durable dye-sensitized solar cells

The design and fabrication of advanced counter electrodes (CEs) for dye-sensitized solar cells (DSSCs) are limited by the scarcity of active sites and poor durability. Herein, we report the controlled preparation of a heterostructured nanoreactor CE based on defect-rich N-doped carbon nanoflowers (NCF) encapsulating MoC/MoO2 nano dots (NDs) in a well-defined heterophase (MoC/MoO2-NCF). The MoC/MoO2 NDs were uniformly dispersed on the NCF, and the NCF limited the size of the MoC/MoO2 NDs and prevented their agglomeration, thus maximizing the electrochemically active surface area of MoC/MoO2. Moreover, the synergistic effect between the MoC/MoO2 interface and the N-defects is conducive to the full exposure of the active sites. Furthermore, theoretical calculations revealed that the MoC/MoO2 heterojunction played a unique role in modulating the electronic structure and regulating the adsorption energy of tri-iodide in the iodide reduction reaction. The MoC/MoO2-NCF CEs in DSSCs demonstrated a power conversion efficiency (PCE) of 9.92% and high durability, exceeding the PCE (8.36%) and durability of Pt CEs. Overall, this study offers insights into the controlled synthesis of high-performance Mo-based composite CE materials for DSSCs.

Single-component organic solar cells-Perspective on the importance of chemical precision in conjugated block copolymers

Organic photovoltaics (OPV) present a promising thin-film solar cell technology with particular benefits in terms of weight, aesthetics, transparency, and cost. However, despite being studied intensively since the mid 90's, OPV has not entered the mass consumer market yet. Although the efficiency gap with other thin-film photovoltaics has largely been overcome, active layer stability and performance reproducibility issues have not been fully resolved. State-of-the-art OPV devices employ a physical mixture of electron donor and acceptor molecules in a bulk heterojunction active layer. These blends are prone to morphological changes, leading to performance losses over time. On the other hand, in "single-component" organic solar cells, the donor and acceptor constituents are chemically connected within a single material, preventing demixing and thereby enhancing device stability. Novel single-component materials affording reasonably high solar cell efficiencies and improved lifetimes have recently emerged. In particular, the combination of donor and acceptor structures in conjugated block copolymers (CBCs) presents an exciting approach. Nevertheless, the current CBCs are poorly defined from a structural point of view, while synthetic protocols remain unoptimized. More controlled synthesis followed by proper structural analysis of CBCs is, however, essential to develop rational structure-property-device relations and to drive the field forward. In this perspective, we provide a short overview of the state-of-the-art in single-component organic solar cells prepared from CBCs, reflect on their troublesome characterization and the importance of chemical precision in these structures, give some recommendations, and discuss the potential impact of these aspects on the field.

Optimized Crystal Framework by Asymmetric Core Isomerization in Selenium-Substituted Acceptor for Efficient Binary Organic Solar Cells

Both the regional isomerization and selenium-substitution of the small molecular acceptors (SMAs) play significant roles in developing efficient organic solar cells (OSCs), while their synergistic effects remain elusive. Herein, we developed three isomeric SMAs (S-CSeF, A-ISeF, and A-OSeF) via subtly manipulating the mono-selenium substituted position (central, inner, or outer) and type of heteroaromatic ring on the central core by synergistic strategies for efficient OSCs, respectively. Crystallography of asymmetric A-OSeF presents a closer intermolecular π-π stacking and more ordered 3-dimensional network packing and efficient charge-hopping pathways. With the successive out-shift of the mono-selenium substituted position, the neat films give a slightly wider band gap and gradually higher crystallinity and electron mobility. The PM1 : A-OSeF afford favourable fibrous phase separation morphology with more ordered molecular packing and efficient charge transportation compared to the other two counterparts. Consequently, the A-OSeF-based devices achieve a champion efficiency of 18.5 %, which represents the record value for the reported selenium-containing SMAs in binary OSCs. Our developed precise molecular engineering of the position and type of selenium-based heteroaromatic ring of SMAs provides a promising synergistic approach to optimizing crystal stacking and boosting top-ranked selenium-containing SMAs-based OSCs.

Efficient Standalone Flexible Small Molecule Organic Solar Cell Devices: Structure-Performance Relation Among Tetracyanoquinodimethane Derivatives

Currently, very few dicyano and tetracyanoquinodimethane (TCNQ) based molecules are utilized as active layers, sandwiched between the electron and hole transport layer in organic solar cell (OSC) devices. Nevertheless, simple mono- and disubstituted TCNQ derivatives as exclusively active layers are yet unexplored and provide scope for further investigation. In this study, TCNQ derivatives with varying amine substituents, namely, AEPYDQ (1), BMEDDQ (2), MATBTCNQ (3), and MITATCNQ (4), were explored as efficient standalone, flexible, all small molecule OSC devices. Particularly, 1 resulted in the highest device efficiency of 11.75% with an aromatic amine, while 2 possessing an aliphatic amine showed the lowest power conversion efficiency (PCE; 2.12%). Notably, the short circuit current density (JSC) of device 1 increased from 2 mA/cm2 in the dark to 9.12 mA/cm2 under light, indicating a significant boost in the current generation. Further, 1 manifested more crystallinity than others. Interestingly, 4 exhibited a higher PCE (5.90%) than 3 (PCE is 2.58%), though 3 is disubstituted with an aromatic amine, probably attributed to the electron-withdrawing effects of the -CF3 and -CN groups in 3 reducing the available π-electron density for stacking. Therefore, this study emphasizes crystallinity, significantly on the PCE, offering insights into the design of many such efficient OSCs.

Progress in organic photovoltaics based on green solvents: from solubility enhancement to morphology optimization

Solution-processed organic photovoltaics (OPVs) is one of the most promising photovoltaic technologies in the energy field, due to their clean and renewable low-cost manufacturing potential. OPV has rapidly developed with the design and synthesis of highly efficient photovoltaic materials and the development of smart device engineering. To date, the majority of advanced OPV devices have been prepared using halogenated solvents, achieving power conversion efficiencies (PCE) exceeding 19% on a laboratory scale. However, for industrial-scale production, less toxic manufacturing processes and environmental sustainability are the key considerations. Therefore, this review summarizes recent advances in green solvent-based approaches for the preparation of OPVs, highlighting material design (including polymer donors and small molecule acceptors) and device engineering (co-solvent methods, additive strategies, post-treatment methods, and regulation of coating method), emphasizing crucial factors for achieving high performance in green solvent-processed OPV devices. This review presents potential future directions for green solvent-based OPVs, which may pave the way for future industrial development.

Synergistic Effect of Size-Tailored Structural Engineering and Postinterface Modification for Highly Efficient and Stable Dye-Sensitized Solar Cells

Despite significant progress in device performance, dye-sensitized solar cells (DSSCs) continue to fall short of their theoretical potential. Moreover, research in recent years needs to pay more attention to improving the device fabrication process. To achieve the theoretical efficiency limit, it is crucial to optimize the interface between the dye and TiO2 nanoparticles in the entire device stack. Our study indicates that optimizing the structure or size of the coadsorbents and implementing a monolayer adsorption process can be an effective strategy to reduce charge recombination and enhance light-harvesting properties. Our research aims to develop a surface-coating adsorbent plan that controls the TiO2 nanoparticle interface to achieve the radiative limit of power conversion efficiency (PCE). Specifically, we utilized 2-thiophenecarboxylic acid (THCA) or chenodeoxycholic acid (CDCA) as postinterfacial surface-coating adsorbents. Our results demonstrate that this approach effectively achieves the desired PCE limit. Combined with the coadsorbent structure engineering and interface optimization, the device increased the packing area on the TiO2 nanoparticles' surface, reaching an improved PCE of over 13.17% under simulated sunlight (1.5G), which is the highest efficiency of a porphyrin single dye-based DSSC. In particular, this practical approach was also applied to a large-area DSSC with an area of 3 cm2, yielding a remarkable PCE of 9.04%. Furthermore, when applied to a polymer gel electrolyte, this novel approach recorded the highest PCE of 11.16% with a long-term operational stability of up to 1000 h for the quasi-solid-state DSSCs. Our research findings provide a promising avenue for achieving high-performance DSSCs with ease of access and demonstrate practical applications as alternatives to conventional power sources.

Self-Doped n-Type Quinoidal Compounds with Good Air Stability and High Electrical Conductivity for Organic Electronics

Air stable n-type conductive molecules with high electrical conductivities and excellent device performance have important applications in organic electronics, but their synthesis remains challenging. Herein, we report three self-doped n-type conductive molecules, designated QnNs, with a closed-shell quinoidal backbone and alkyl amino chains of different lengths. The QnNs are self-doped by intermolecular electron transfer from the amino groups to the quinoidal backbone. This process is ascertained unambiguously by experiments and theoretical calculations. The use of a quinoidal structure effectively improves the self-doping level, and thus increases the electrical conductivity of self-doped n-type conductive molecules achieved by a closed-shell structure from<10-4  S cm-1 to>0.03 S cm-1 . Furthermore, the closed-shell quinoidal structure results in good air stability of the QnNs, with half-lives>73 days; and Q4N shows an electrical conductivity of 0.019 S cm-1 even after exposure to air for 120 days. When applying Q6N as the cathode interlayer in organic solar cells (OSCs), an outstanding power conversion efficiency of up to 18.2 % was obtained, which represents one the best results in binary OSCs.

Excited-State Dynamics in All-Polymer Blends with Polymerized Small-Molecule Acceptors

Polymerizing small-molecular acceptors (SMAs) is a promising route to construct high performance polymer acceptors of all-polymer solar cells (all-PSCs). After SMA polymerization, the microstructure of molecular packing is largely modified, which is essential in regulating the excited-state dynamics during the photon-to-current conversion. Nevertheless, the relationship between the molecular packing and excited-state dynamics in polymerized SMAs (PSMAs) remains poorly understood. Herein, the excited-state dynamics and molecular packing are investigated in the corresponding PSMA and SMA utilizing a combination of experimental and theoretical methods. This study finds that the charge separation from intra-moiety delocalized states (i-DEs) is much faster in blends with PSMAs, but the loosed π-π molecular packing suppresses the excitation conversion from the local excitation (LE) to the i-DE, leading to additional radiative losses from LEs. Moreover, the increased aggregations of PSMA in the blends decrease donor: acceptor interfaces, which reduces triplet losses from the bimolecular charge recombination. These findings suggest that excited-state dynamics may be manipulated by the molecular packing in blends with PSMAs to further optimize the performance of all-PSCs.

A Wide Bandgap Acceptor with Large Dielectric Constant and High Electrostatic Potential Values for Efficient Organic Photovoltaic Cells

Low-bandgap materials have achieved rapid development and promoted the enhancement of power conversion efficiencies (PCEs) of organic photovoltaic (OPV) cells. However, the design of wide-bandgap non-fullerene acceptors (WBG-NFAs), required by indoor applications and tandem cells, has been lagging far behind the development of OPV technologies. Here, we designed and synthesized two NFAs named ITCC-Cl and TIDC-Cl by finely optimizing ITCC. In contrast with ITCC and ITCC-Cl, TIDC-Cl can maintain a wider bandgap and a higher electrostatic potential simultaneously. When blending with the donor PB2, the highest dielectric constant is also obtained in TIDC-Cl-based films, enabling efficient charge generation. Therefore, the PB2:TIDC-Cl-based cell possessed a high PCE of 13.8% with an excellent fill factor (FF) of 78.2% under the air mass 1.5G (AM 1.5G) condition. Furthermore, an exciting PCE of 27.1% can be accomplished in the PB2:TIDC-Cl system under the illumination of 500 lux (2700 K light-emitting diode). Combined with the theoretical simulation, the tandem OPV cell based on TIDC-Cl was fabricated and exhibited an excellent PCE of 20.0%.

Unraveling the Role of Non-Fullerene Acceptor with High Dielectric Constant in Organic Solar Cells

Increasing the relative dielectric constant is a constant pursuit of organic semiconductors, but it often leads to multiple changes in device characteristics, hindering the establishment of a reliable relationship between dielectric constant and photovoltaic performance. Herein, a new non-fullerene acceptor named BTP-OE is reported by replacing the branched alkyl chains on Y6-BO with branched oligoethylene oxide chains. This replacement successfully increases the relative dielectric constant from 3.28 to 4.62. To surprise, BTP-OE offers consistently lower device performance relative to Y6-BO in organic solar cells (16.27% vs 17.44%) due to the losses in open-circuit voltage and fill factor. Further investigations unravel that BTP-OE has resulted in reduced electron mobility, increased trap density, enhanced first order recombination, and enlarged energetic disorder. These results demonstrate the complex relationship between dielectric constant and device performance, which provide valuable implications for the development of organic semiconductors with high dielectric constant for photovoltaic application.

Long-Range Ordered Organic Bulk-Heterojunction: C60 and O-IDTBR Single Crystals Penetrated by Crystalline P3HT Fibrous Networks

The long-range ordering of bulk-heterojunctions (BHJs) significantly facilitates exciton diffusion and dissociation as well as charge transport. A feasible bio-inspired strategy to realize such a heterostructure is crystallization in gel media where the growing host crystals incorporate the surrounding guest materials of gel networks. Until now, the host-guest pairs forming ordered BHJs are still very limited and, more importantly, the used gel-network guests are structurally amorphous, spurring investigation toward crystalline gel-networks. Here, single crystals of fullerene and non-fullerene acceptors (NFAs) in poly(3-hexylthiophene) (P3HT) organogel are prepared, forming C₆₀ :P3HT and (5Z,5″Z)-5,5″-((7,7″-(4,4,9,9-tetraoctyl-4,9-dihydro-s-indaceno[1,2-b:5,6-b″]dithiophene-2,7-diyl)bis(benzo[c][1,2,5]thiadiazole-7,4-diyl))bis(methanylylidene))bis(3-ethyl-2-thioxothiazolidin-4-one) (O-IDTBR):P3HT BHJs. The crystalline P3HT network penetrates the crystal matrix without significantly disturbing the single crystallinity, resulting in long-range ordered BHJs. This bi-continuous structure, together with an improved overall ordering, contributes to enhanced charge/energy transfer. As a result, photodetectors based on these ordered BHJs exhibit ameliorated responsivity, detectivity, bandwidth, and stability as compared to the conventional BHJs with short-range ordering. Therefore, this work further extends the scope of long-range ordered BHJs toward crystalline polymer donors and NFAs, providing a generally applicable strategy for the design of organic optoelectronic devices with superior performance.

Large Steric Hindrance Enhanced Molecular Planarity for Low-Cost Non-Fused Electron Acceptors

Designing efficient non-fused ring electron acceptors is of great importance in decreasing the material cost of organic photovoltaic cells (OPVs). It is a challenge to construct a planar molecular skeleton in non-fused molecules as there are many torsions between adjacent units. Here, we design two non-fused electron acceptors based on bithieno[3,2-b]thiophene units as core structures and study the impact of steric hindrance of substituents on molecular planarity. We use 2,4,6-triisopropylphenyl and 4-hexylphenyl groups to prepare ATTP-1 and ATTP-2, respectively. Our results suggest that the enhanced steric hindrance is beneficial for obtaining a more planar molecular configuration, which significantly increases the optical absorption and charge transport properties. The power conversion efficiency (PCE) of PBDB-TF:ATTP-1 combination (11.3%) is superior to that of PBDB-TF:ATTP-2 combination (3.7%). In addition, an impressive PCE of 10.7% is recorded in ATTP-1-based devices when a low-cost polythiophene donor PDCBT is used, which is an outstanding value in OPVs fabricated by non-fused donor/acceptor combinations. Our work demonstrates that modulation of the steric hindrance effect is of great significance to control the molecular planarity and thus obtain excellent photovoltaic performance of low-cost non-fused electron acceptors.

Double Asymmetric Core Optimizes Crystal Packing to Enable Selenophene-based Acceptor with Over 18 % Efficiency in Binary Organic Solar Cells

Side-chain tailoring is a promising method to optimize the performance of organic solar cells (OSCs). However, asymmetric alkyl chain-based small molecular acceptors (SMAs) are still difficult to afford. Herein, we adopted a novel asymmetric n-nonyl/undecyl substitution strategy and synthesized two A-D₁ A'D₂ -A double asymmetric isomeric SMAs with asymmetric selenophene-based central core for OSCs. Crystallographic analysis indicates that AYT9Se11-Cl forms a more compact and order intermolecular packing compared to AYT11Se9-Cl, which contributed to higher electron mobility in neat AYT9Se11-Cl film. Moreover, the PM6 : AYT9Se11-Cl blend film shows a better morphology with appropriate phase separation and distinct face-on orientation than PM6 : AYT11Se9-Cl. The OSCs with PM6 : AYT9Se11-Cl obtain a superior PCE of 18.12 % compared to PM6 : AYT11Se9-Cl (17.52 %), which is the best efficiency for the selenium-incorporated SMAs in binary BHJ OSCs. Our findings elucidate that the promising double asymmetric strategy with isomeric alkyl chains precisely modulates the crystal packing and enhances the photovoltaic efficiency of selenophene-incorporated SMAs.

Role of Exciton Lifetime, Energetic Offsets, and Disorder in Voltage Loss of Bulk Heterojunction Organic Solar Cells

Recently, the power conversion efficiency (PCE) of organic solar cells (OSCs) has significantly progressed with a rapid increase from 10 to 19% due to state-of-the-art research on nonfullerene acceptor molecules and various device processing strategies. However, OSCs still exhibit significant open circuit voltage loss (ΔV_OC ∼ 0.6 V) due to high energetic offsets and molecular disorder. In this work, we present a systematic investigation to determine the effects of energetic offset and disorder on different recombination losses in open circuit voltage (V_OC) using 13 different photoactive layers, wherein the PCE and ΔV_OC vary in the ranges of 2.21-14.74% and 0.561-1.443 V, respectively. The detailed voltage loss analysis of all these devices was carried out, and voltage losses were correlated with energetic offset and disorder. This has enabled us to identify the key features for minimizing the voltage loss like: (1) a low energy offset between the donor and acceptor molecular states is essential to attain a nonradiative voltage loss (ΔV_OC, nrad) as low as ∼200 meV and (2) Urbach energy, which is a measure of the materials' disorder and packing, should be low for the minimization of the radiative voltage loss (ΔV_OC, rad). In addition, time-resolved photoluminescence spectroscopy was employed to further understand the exciton dynamics of pristine materials and donor-acceptor blends. It was observed that the absorbers with ultralong exciton lifetime (∼1000 ps) produce higher efficiencies. The current study emphasizes the importance of simultaneously testing photovoltaic performance and active layer exciton dynamics for rational device optimization and opens new prospects for designing novel molecules with fine-tuning of energetic offset and disorder with longer exciton lifetime which is the effective strategy to boost the efficiency of OSCs to their modified Shockley-Queisser (SQ) limit by minimizing radiative and nonradiative voltage losses.