A FRET-based dual-color evanescent wave optical fiber aptasensor for simultaneous fluorometric determination of aflatoxin M1 and ochratoxin A

Fiber Optic LSPR Sensing AFM1 in Milk with Enhanced Sensitivity by the Hot Spot Effect Based on Nanogap Construction

The detection of the amount of aflatoxin M1 (AFM1) in milk is crucial for food safety. Here, we utilize a fiber optic (FO) localized surface plasmon resonance (LSPR) biosensor by constructing gold nanoparticle (AuNP) multimers, in which the nanogaps amplified the LSPR signal by the hot spot effect, and achieved a highly sensitive detection of f AFM1. Through the optimization of parameter conditions for the fabrication of the sensor and detection system, a high performance result from the FO LSPR biosensor was obtained, and the method for AFM1 detection was established, with a wide detection range of 0.05-100 ng/mL and a low limit of detection (LOD) of 0.04 ng/mL, and it has been successfully validated with the actual sample milk. Therefore, it is a good strategy to fabricate highly sensitive FO LSPR sensors for detecting AFM1 by constructing AuNP multimers, and this approach is suitable for developing other biosensors.

Plasmonic immunosensors based on spoon-shaped waveguides for fast and on-site ultra-low detection of ochratoxin A in coffee samples

The high toxicity and occurrence of ochratoxin A (OTA) in grains and foods has been a growing concern due to the impacts on health and the economy in many countries. In this sense, simplified devices with high sensitivity and specificity for local monitoring are enthusiastically pursued. In this work, we report for the first time the detection of ochratoxin A in coffee samples using a spoon-shaped waveguide immunosensor. The biosensor was built with the surface of the spoon-shaped waveguide covered by a 60 nm layer of gold to enable the SPR phenomenon. The measurements indicated a linear relationship between the change in the SPR phenomenon values and the OTA concentration in the range from 0.2 ppt to 5 ppt. When analyzed in coffee samples, the biosensor was highly selective and did not suffer matrix interference. The developed biosensor represents a promising analytical device for coffee quality analyses, as it is portable, simple, and suitable for onsite detection of target analytes.

FOXM1 aptamer-polyethylenimine nanoplatform coated with hyaluronic acid and AS1411 aptamer for dual-targeted delivery of doxorubicin and synergistic treatment of tumor cells

The objective of this investigation was to develop a self-assembled, dual-functionalized delivery system that could effectively transport doxorubicin (DOX) to cancer cells through the use of AS1411 aptamer and hyaluronic acid polymer (HA). The ultimate goal is an improved targeting approach for more efficient treatment. The core of this system comprised polyethylenimine (PEI) and FOXM1 aptamer, which was coated by HA. Next, nucleolin targeting aptamers (AS1411) were loaded onto the nanocomplex. Afterward, DOX was added to Aptamers (Apts)-HA-PEI-FOXM1 NPs to create the DOX-AS1411-HA-PEI-FOXM1 NPs for better treatment of cancer cells. The cytotoxic effect of the nanocomplex on L929, 4T1, and A549 cells showed that cell mortality in target cancer cells (4T1 and A549) was considerably enhanced compared to nontarget cells (L929, normal cells). The findings from the flow cytometry analysis and fluorescence imaging demonstrated the cellular absorption of DOX-Apts-HA-PEI-FOXM1 NPs in target cells was significantly enhanced when compared to L929 cells. Furthermore, in vivo antitumor study exhibited that DOX-Apts-HA-PEI-FOXM1 NPs rendered specific tumor accumulation and increasing of the anti-tumor effects.

Recent Progress in Functional-Nucleic-Acid-Based Fluorescent Fiber-Optic Evanescent Wave Biosensors

Biosensors capable of onsite and continuous detection of environmental and food pollutants and biomarkers are highly desired, but only a few sensing platforms meet the "2-SAR" requirements (sensitivity, specificity, affordability, automation, rapidity, and reusability). A fiber optic evanescent wave (FOEW) sensor is an attractive type of portable device that has the advantages of high sensitivity, low cost, good reusability, and long-term stability. By utilizing functional nucleic acids (FNAs) such as aptamers, DNAzymes, and rational designed nucleic acid probes as specific recognition ligands, the FOEW sensor has been demonstrated to be a general sensing platform for the onsite and continuous detection of various targets ranging from small molecules and heavy metal ions to proteins, nucleic acids, and pathogens. In this review, we cover the progress of the fluorescent FNA-based FOEW biosensor since its first report in 1995. We focus on the chemical modification of the optical fiber and the sensing mechanisms for the five above-mentioned types of targets. The challenges and prospects on the isolation of high-quality aptamers, reagent-free detection, long-term stability under application conditions, and high throughput are also included in this review to highlight the future trends for the development of FOEW biosensors capable of onsite and continuous detection.

Liquid-Core Hydrogel Optical Fiber Fluorescence Probes

This paper first reports a liquid-core hydrogel optical fiber fluorescence probe. It is composed of a liquid core, a high-refractive-index hydrogel fiber core, and a low-refractive-index hydrogel fiber cladding, which is completely different from many existing optical fiber fluorescence probes. The sensing solution with sensitive materials is sealed as a liquid core, and it can sufficiently react with small-molecule targets penetrating through the hydrogel fiber cladding and core, thus inducing variations in the fluorescence signals. These fluorescence signals can be localized and transmitted within the probe and finally collected and quantified for target detection. This proposed probe can be simply and rapidly fabricated and reused, and it was proven to have high sensitivity, accuracy, and selectivity in practical applications. Therefore, this liquid-core hydrogel optical fiber fluorescence probe will enable a novel sensing platform for small-molecule analyte detection that faces on-site detection challenges.

Recent advances in simultaneous detection strategies for multi-mycotoxins in foods

Mycotoxin contamination has become a challenge in the field of food safety testing, given the increasing emphasis on food safety in recent years. Mycotoxins are widely distributed, in heavily polluted areas. Food contamination with these toxins is difficult to prevent and control. Mycotoxins, as are small-molecule toxic metabolites produced by several species belonging to the genera Aspergillus, Fusarium, and Penicillium growing in food. They are considered teratogenic, carcinogenic, and mutagenic to humans and animals. Food systems are often simultaneously contaminated with multiple mycotoxins. Due to the additive or synergistic toxicological effects caused by the co-existence of multiple mycotoxins, their individual detection requires reliable, accurate, and high-throughput techniques. Currently available, methods for the detection of multiple mycotoxins are mainly based on chromatography, spectroscopy (colorimetry, fluorescence, and surface-enhanced Raman scattering), and electrochemistry. This review provides a comprehensive overview of advances in the multiple detection methods of mycotoxins during the recent 5 years. The principles and features of these techniques are described. The practical applications and challenges associated with assays for multiple detection methods of mycotoxins are summarized. The potential for future development and application is discussed in an effort, to provide standards of references for further research.

Detection of Potential Microbial Contaminants and Their Toxins in Fermented Dairy Products: a Comprehensive Review

Fermented dairy products are dominant constituents of daily diets around the world due to their desired organoleptic properties, long shelf life, and high nutritional value. Probiotics are often incorporated into these products for their health and technological benefits. However, the safety and possible contamination of fermented dairy products during the manufacturing process could have significant deleterious health and economic impacts. Pathogenic microorganisms and toxins from different sources in fermented dairy products contribute to outbreaks and toxicity cases. Although the health and nutritional benefits of fermented dairy products have been extensively investigated, safety hazards due to contamination are relatively less explored. As a preventive measure, it is crucial to accurately identify and determine the associated microbiota or their toxins. It is noteworthy to highlight the importance of detecting not only the pathogenic microbiota but also their toxic metabolites so that putative outbreaks can thereby be prevented or detected even before they cause harmful effects to human health. In this context, this review focuses on describing techniques designed to detect potential contaminants; also, the advantages and disadvantages of these techniques were summarized. Moreover, this review compiles the most recent and efficient analytical methods for detecting microbial hazards and toxins in different fermented dairy products of different origins. Causative agents behind contamination incidences are also discussed briefly to aid in future prevention measures, as well as detection approaches and technologies employed. Such approach enables the elucidation of the best strategies to control contamination in fermented dairy product manufacturing processes.

Overview and emerging trends in optical fiber aptasensing

Optical fiber biosensors have attracted growing interest over the last decade and quickly became a key enabling technology, especially for the detection of biomarkers at extremely low concentrations and in small volumes. Among the many and recent fiber-optic sensing amenities, aptamers-based sensors have shown unequalled performances in terms of ease of production, specificity, and sensitivity. The immobilization of small and highly stable bioreceptors such as DNA has bolstered their use for the most varied applications e.g., medical diagnosis, food safety and environmental monitoring. This review highlights the recent advances in aptamer-based optical fiber biosensors. An in-depth analysis of the literature summarizes different fiber-optic structures and biochemical strategies for molecular detection and immobilization of receptors over diverse surfaces. In this review, we analyze the features offered by those sensors and discuss about the next challenges to be addressed. This overview investigates both biochemical and optical parameters, drawing the guiding lines for forthcoming innovations and prospects in this ever-growing field of research.

A sandwich-based evanescent wave fluorescent biosensor for simple, real-time exosome detection†

Exosomes are regarded as a promising biomarker for the noninvasive diagnosis and treatment of diseases. The value of exosomes for medical research has promoted the search for a fast, efficient, and sensitive detection method. This study reported a sandwich-based evanescent wave fluorescent biosensor (S-EWFB) for exosome detection. A two-step strategy was implemented to take advantages of the simple binding of fluorescent probes with exosomes via the hydrophobic interaction between the cholesteryl and phospholipid bilayer membrane, as well as real-time detection on an evanescent wave liquid-solid interface based on CD63 aptamer-specific capture to form an exosome@fluorescence probe/aptamer sandwich structure. The one-to-many connection between exosomes and signal molecules and the aptamer-modified evanescent wave optical fiber detection platform reduced the detection limit of exosomes to 7.66 particles/mL, with a linear range of 47.5-4.75 × 10⁶ particles/mL. The entire detection process was simple, rapid, and real-time and lasted about 1 h while requiring no separation and purification. Additionally, this platform showed excellent surface regeneration capability and exhibited good performance during the analysis of tumor and non-tumor-derived exosomes.

A bivalent binding aptamer-cDNA on MoS2 nanosheets based fluorescent aptasensor for detection of aflatoxin M1

To ensure the safety of dairy products, especially milk, and consequently protect human health, accurate and simple analytical techniques are highly necessary to determine the low concentration of aflatoxin M₁ (AFM₁) as an important carcinogen. Herein, a novel, accurate and simple fluorescent aptasensor was designed for selective detection of AFM₁ based on bivalent binding aptamer-cDNA (BBA-cDNA) structure. Moreover, MoS₂ nanosheets (MoS₂ NSs) were used as the fluorescent quencher and FAM-labeled complementary strand of aptamer (FAM-CS) was applied as a fluorescent probe. In this study, we achieved a new result. Unlike previous studies, in this work, the BBA-cDNA structure was not disassembled in the presence of the target. Therefore, as the AFM1 concentration increased, more targets were attached to the BBA-cDNA structure and as a result, the BBA-cDNA structure/AFM1 could not be placed on the surface of MoS2 NSs, leading to the more fluorescent intensity detection. Under optimized conditions, the developed fluorescent analytical method revealed great selectivity toward AFM₁ with a limit of detection (LOD) of 0.5 nM and a linear range from 0.7 to 10 nM. This fabricated aptasensor indicated excellent analytical performance for AFM₁ detection in milk samples with LOD of 0.1 nM. Overall, the proposed approach could provide an effective basis for small molecule analysis to guarantee food and human safety using appropriate aptamer sequences.

Ratiometric fluorescence probe of Cu2+ and biothiols by using carbon dots and copper nanoclusters

A novel dual-emission ratiometric fluorescent probe based on N-doped yellow fluorescent carbon dots (y-CDs) and blue fluorescent copper nanoclusters (CuNCs) was established for quantitative determination of Cu²⁺ and biothiols. In this work, the Cu²⁺-(y-CDs) complexes formed by the chelation of y-CDs with Cu²⁺, showed an absorption peak at 430 nm that not only enhanced the fluorescence of y-CDs through inhibiting photoinduced electron transfer (PET) but also effectively quenched the fluorescence of CuNCs due to Förster resonance energy transfer (FRET). In addition, the chelation of y-CDs with Cu²⁺ could be inhibited by biothiols that prevented the fluorescence of y-CDs from being enhanced and the fluorescence of CuNCs from being quenched. On account of the changes of ratiometric signal, a dual-emission fluorescence probe for Cu²⁺ and biothiols determination was achieved. The proposed method exhibited high sensitivity for Cu²⁺ and biothiols in the ranges of 0.5-100 μM and 0.8-50 μM and the limits of detection (LODs) of Cu²⁺, glutathione (GSH), cysteine (Cys) and homocysteine (Hcy) were 0.21 μM, 0.33 μM, 0.39 μM and 0.46 μM, respectively. Subsequently, the established strategy presented an application prospect for the detection of Cu²⁺ and biothiols in real samples.

Application of the Dimeric G-Quadruplex and toehold-mediated strand displacement reaction for fluorescence biosensing of ochratoxin A

Ochratoxin A (OTA) is one of the most toxic mycotoxins that exists in various agro-products and foods. Here, a non-label and enzyme-free fluorescence biosensor for highly specific detection of OTA has been developed by the combination of toehold-mediated strand displacement reaction (TMSD) and G-quadruplex dimer/ThT (G-dimer/ThT). The DNA duplex (aptamer-IP) is composed of the anti-OTA aptamer and a single stranded initiation probe (IP). In the presence of OTA, the attachment of target to aptamer leads to the liberation of the IP, which activates the cycle TMSD amplifications of two hairpin probes (H1 and H2) accompanied by the production of numerous H1-H2 assemblies. This double-stranded H1-H2 structure results in the proximity between the 5'-end overhang tail of H1 and the 3'-end stem of H2 to liberate the pre-blocked G-dimer sequence for lighting up ThT. In addition, the method displayed a stable fluorescence emission in the high-salt media. It was successfully applied to analyze OTA in real food samples. Hence, the constructed fluorescence biosensing platform might provide a new way for OTA and other toxin analysis detection.

A novel colorimetric aptasensor for ultrasensitive detection of aflatoxin M1 based on the combination of CRISPR-Cas12a, rolling circle amplification and catalytic activity of gold nanoparticles

Colorimetric approaches have received noticeable attention among sensing methods in view of simplicity and watching the color change of sample by the naked eyes. However, developing colorimetric sensing methods which show high sensitivity is still problematic. Herein, based on CRISPR-Cas12a, rolling circle amplification (RCA) and catalytic activity of gold nanoparticles (AuNPs), a colorimetric aptasensor was introduced for highly sensitive detection of aflatoxin M₁ (AFM₁). In the presence of AFM₁, the CRISPR-Cas12a is inactivated and large single-stranded DNA (ssDNA) structures are formed on the surface of AuNPs following the addition of T4 DNA ligase and phi29 DNA polymerase. So, the sample color remains yellow after addition of 4-nitrophenol. However, no huge DNA structure is observed on the surface of AuNPs in the absence of target because of activation of CRISPR-Cas12a and digestion of primer. So, the color of sample switches to colorless. The results indicated that the biosensor had high selectivity toward AFM₁ and the approach achieved a detection limit as low as 0.05 ng/L. In addition, it could sensitively identify AFM₁ in the spiked milk samples. Overall, this approach is highly sensitive and does not require sophisticated equipment. Therefore, it maintains promising potential for other mycotoxins detection in real samples by simply replacing the applied sequences.

Effects of Viscosity and Refractive Index on the Emission and Diffusion Properties of Alexa Fluor 405 Using Fluorescence Correlation and Lifetime Spectroscopies

Fluorescence Correlation Spectroscopy (FCS) studies of the interaction of polymers or proteins in solution are strongly affected by the viscosity and refractive index of the medium, and the effects are likely to be more significant with the use of short wavelength excitation (e.g., 405 nm diode lasers). Failing to account for these issues can lead to incorrect measurement of average size, conformational changes, and dynamic behaviour of polymers and proteins. Steady-state, time-resolved, and FCS measurements of Alexa 405 in glycerol:water mixtures were performed to determine its suitability for FCS measurements with 405 nm excitation. The effects of the refractive index and viscosity on the diffusion coefficient and photophysical parameters (lifetime and relative quantum yield) of the fluorophore were determined. Alexa 405 lifetime decreased from 3.55 ns in water to 3.25 ns in a 50:50 glycerol:water mixture, while its diffusion coefficient dropped from 333 ± 16 to 44 ± 1 µm²s^- 1. Lifetime data collected from micromolar solutions of Alexa 405 did however also suggest that as solvent polarity decreased, aggregates (excimers) were formed as evidenced by the appearance of a rising edge in the decay plots. The interdependence between lifetime, refractive index, and diffusion coefficient could be accurately fitted by a simple polynomial function indicating that the probe is well behaved and predictable in the glycerol:water model system. Overall, Alexa 405 is a most promising and reliable probe for FCS measurement using violet laser diode excitation sources.

Aptasensors for mycotoxin detection: A review

Mycotoxins are toxic compounds produced by fungi, which represent a risk to the food and feed supply chain, having an impact on health and economies. A high percentage of feed samples have been reported to be contaminated with more than one type of mycotoxin. Systematic, cost-effective and simple tools for testing are critical to achieve a rapid and accurate screening of food and feed quality. In this review, we describe the various aptamers that have been selected against mycotoxins and their incorporation into optical and electrochemical aptasensors, outlining the strategies exploited, highlighting the advantages and disadvantages of each approach. The review also discusses the different materials used and the immobilization methods employed, with the aim of achieving the highest sensitivity and selectivity.

An optical aptasensor for aflatoxin M1 detection based on target-induced protection of gold nanoparticles against salt-induced aggregation and silica nanoparticles

Not only intoxications of aflatoxins are significant risk for human beings, but also; the contamination with these toxins affect the economy. Therefore, developing a rapid, precise and inexpensive determination method is vitally important. Here, a colorimetric aptasensor is introduced for the detection of aflatoxin M₁ (AFM₁) based on the preservation of gold nanoparticles (AuNPs) against NaCl-induced aggregation by detaching of complementary strand of aptamer (CS) from the aptamer-modified streptavidin coated silica nanoparticles (SNPs) following the addition of target. So, the color of sample remains red. While, in the lack of AFM₁, salt-induced aggregation of AuNPs occurs and the color of sample becomes purple as the aptamer/CS (dsDNA)-modified SNPs is stable and CS cannot bind to AuNPs. The proposed aptasensor could detect AFM₁ in a linear dynamic range, 300-75,000 ng/L, with a detection limit of 30 ng/L. Also, the sensing method was effectively applied for AFM₁ recognition in milk samples.

An ultrasensitive, homogeneous fluorescence quenching immunoassay integrating separation and detection of aflatoxin M1 based on magnetic graphene composites

A homogeneous fluorescence quenching immunoassay is described for simultaneous separation and detection of aflatoxin M₁ (AFM₁) in milk. The novel assay relies on monoclonal antibody (mAb) functionalized Fe₃O₄ decorated reduced-graphene oxide (rGO-Fe₃O₄-mAb) as both capture probe and energy acceptor, combined with tetramethylrhodamine cadaverine-labeled aflatoxin B₁ (AFB₁-TRCA) as the energy donor. In the assay, AFB₁-TRCA binds to rGO-Fe₃O₄-mAb in the absence of AFM₁, quenching the fluorescence of TRCA by resonance energy transfer. Significantly, the immunoassay integrates sample preparation and detection into a single step, by using magnetic graphene composites to avoid washing and centrifugation steps, and the assay can be completed within 10 min. Under optimized conditions, the visual and quantitative detection limits of the assay for AFM₁ were 50 and 3.8 ng L^-1, respectively, which were significantly lower than those obtained by fluorescence polarization immunoassay using the same immunoreagents. Owing to its operation and highly sensitivity, the proposed assay provides a powerful tool for the detection of AFM₁.

Reusable optofluidic point-of-care testing platform with lyophilized specific antibody for fluorescence detection of cholylglycine in serum

A reusable optofluidic point-of-care testing platform (OPOCT) was successfully constructed through integrating evanescent wave fluorescence technology into an all-fiber-based optofluidic system. The compact design of the OPOCT allows it to be portable and suitable for on-site sensitive determination of biomarkers in serum without complicated and costly procedures. The sensitivity of 90.9 pM for antibody determination is observed thanks to the high transmission efficiency of excitation light and fluorescence in the OPOCT. The affinity constant between cholylglycine (CG) and anti-CG antibody was quantified using this platform based on the proposed theory. Using the lyophilized fluorescence-labeled specific antibody and reusable fiber optic biosensor, the OPOCT is applied to the one-step sensitive determination of CG in serum, which eliminates the dearth associated with liquid reagent handling, disposable biosensors, and user intervention. A limit of detection of 0.025 μg/mL for CG is obtained, which is far more than adequate for meeting diagnostic requirements. The matrix effect of serum samples on the evanescent wave-based optofluidic biosensor can be effectively reduced by simple dilution of serum samples. The performance of the OPOCT also compared favorably with that of a commercial turbidimetric inhibition immunoassay through analyzing multiple serum samples. This platform is ready to expand to measure any other biomarker by using its specific antibody. The simplicity, sensitivity, cost-effectiveness, and robustness of the OPOCT enable the early diagnosis of disease and making a timely clinical decision. Graphical abstract .

Target-responsive ratiometric fluorescent aptasensor for OTA based on energy transfer between [Ru(bpy)3]2+ and silica quantum dots

A ratiometric fluorescent aptasensor based on energy transfer between [Ru(bpy)₃]²⁺ and silica quantum dots (silica QDs) for assaying OTA was fabricated. The aptamer for OTA was used as the gate to shield the fluorescent reagent [Ru(bpy)₃]²⁺ into mesoporous silica nanoparticle (MSN). In the presence of OTA, the constrained [Ru(bpy)₃]²⁺ was released from MSN due to a target-induced aptamer conformational change. The released [Ru(bpy)₃]²⁺ adsorbed onto the negatively charged silica QDs through electrostatic interaction. This creates appearance of fluorescence from [Ru(bpy)₃]²⁺ at 625 nm and decrease of the fluorescence from silica QDs at 442 nm owing to the energy transfer. The value of FL_625nm/FL_442nm was in proportion to the concentration of OTA in the range 0.5~100 ng mL^-1 with a LOD of 0.08 ng mL^-1. Practical applicability of this method was validated by the determination of OTA in flour samples. Graphical abstract The sensing principle of this sensor.

A review on recent developments in optical and electrochemical aptamer-based assays for mycotoxins using advanced nanomaterials

This review (with 163 refs) covers the recent developments of nanomaterial-based optical and electrochemical sensors for mycotoxins. The review starts with a brief discussion on occurrence, distribution, toxicity of mycotoxins and the legislations in monitoring their levels. It further outlines the research methods, various recognition matrices and the strategies involved in the development of highly sensitive and selective sensor systems. It also points out the salient features and importance of aptasensors in the detection of mycotoxins along with the different immobilization methods of aptamers. The review meticulously discusses the performance of different optical and electrochemical sensors fabricated using aptamers coupled with nanomaterials (CNT, graphene, metal nanoparticles and metal oxide nanoparticles). The review addresses the limitations in the current developments as well as the future challenges involved in the successful construction of aptasensors with the functionalized nanomaterials. Graphical abstract Recent developments in nanomaterial based aptasensors for mycotoxins are summarized. Specifically, the efficiency of the nanomaterial coupled aptasensors (such as CNT, graphene, metal nanoparticles and metal oxide nanoparticles) in optical and electrochemical methods are discussed.

Reusable chemiluminescent fiber optic aptasensor for the determination of 17β-estradiol in water samples

A reusable fiber optic chemiluminescent aptasensor (FOCA) is reported for the rapid and sensitive on-site detection of 17β-estradiol (E2), an endocrine-disrupting compound frequently found in water samples. The E2-ovalbumin conjugate (E2-OVA) was covalently immobilized onto the optical fiber as a biorecognition element as well as a transducer. The affinity constant of the E2/aptamer complex was determined to be 1.35 × 10⁶ M^-1 using the FOCA. An indirect competitive assay was then developed for E2 detection. A certain concentration of HRP-E2 aptamers pre-reacted with samples containing E2 in various concentrations. Part of HRP-E2 aptamers specially bound to the sensor surface after introduction of the mixture. This catalyzed the chemiluminescece reaction of a chemiluminescent system composed of luminol and H₂O₂. A higher concentration of E2 led to less HRP-E2 aptamer bound to the biosensor surface, thus resulting in less chemiluminescence. Highly sensitive detection of E2 was achieved under optimal conditions, and the limit of detection is 48 ng ·L^-1 (0.18 nM). The whole analytical process, including measurement and regeneration, can be performed in <15 min. The robustness of the biosensor allows its application to multiple assays with little activity loss. The selectivity, recovery, and accuracy of the sensor was demonstrated by evaluating its response to potentially interfering endocrine disruptors in spiked water samples. Graphical abstract Schematic diagram of the fiber optic chemiluminescent aptasensor system (A), detection mechanism of 17β-estradiol (B), and its application for detection of 17β-estradiol with rapidity and sensitivity (C and D).

A rapid and simple ratiometric fluorescent sensor for patulin detection based on a stabilized DNA duplex probe containing less amount of aptamer-involved base pairs

In this study, a sensor is described for determination of patulin by using ratiometric fluorescence measurement and strand displacement strategy. In the presence of patulin, the ratiometric fluorescence response decreases, owing to disassembly of DNA duplex structure and target-mediated release of TAMRA-labeled complementary DNA sequence2 (cDNA2). While, in the absence of target, the fluorescence resonance energy transfer (FRET) phenomenon happens between FAM and TAMRA under excitation at 490 nm, resulting in the enhancement of ratiometric signal. The use of ratiometric fluorescence signal with different signal indicators avoids the problem of environmental interference and improves the sensitivity of the aptasensor. Also, the DNA duplex structure contains minimum aptamer-involved base pair sequence, resulting in further improvement of the aptasensor sensitivity. This sensing platform provided a wide linear range from 15 ng/L to 35 μg/L and a detection limit of 6 ng/L for patulin. The aptasensor was used to determine patulin in spiked apple juice samples and showed satisfactory results.

Primer remodeling amplification-activated multisite-catalytic hairpin assembly enabling the concurrent formation of Y-shaped DNA nanotorches for the fluorescence assay of ochratoxin A

DNA can be configured into unique high-order structures due to its significantly high programmability, such as a three-way junction-based structure (denoted Y-shaped DNA), for further applications. Herein, we report a label-free fluorescent signal-on biosensor based on the target-driven primer remodeling rolling circle amplification (RCA)-activated multisite-catalytic hairpin assembly (CHA) enabling the concurrent formation of Y-shaped DNA nanotorches (Y-DNTs) for ultrasensitive detection of ochratoxin A (OTA). Two kinds of masterfully-designed probes, termed Complex I and II, were pre-prepared by the combination of a circular template (CT) with an OTA aptamer (S1), a substrate probe (S2) and hairpin probe 1 (HP1), respectively. Target OTA specifically binds to Complex I, resulting in the release of the remnant element in S2 and successive remodeling into a mature primer for RCA by phi29 DNA polymerase, thus a usable primer-CT complex is produced, which actuates primary RCA. Then, numerous Complex II probes can anneal with the first-generation RCA product (RP) with multiple sites to activate the CHA process. With the participation of endonuclease IV (Endo IV) and phi29, HP1 as a pre-primer containing a tetrahydrofuran abasic site mimic (AP site) in Complex II is converted into a mature primer to initiate additional rounds of RCA. So, countless Y-DNTs are formed concurrently containing a G-quadruplex structure that enables the N-methylmesoporphyrin IX (NMM) to be embedded, generating remarkably strong fluorescence signals. The biosensor was demonstrated to enable rapid and accurate highly efficient and selective detection of OTA with an improved detection limit of as low as 0.0002 ng mL^-1 and a widened dynamic range of over 4 orders of magnitude. Meanwhile, this method was proven to be capable of being used to analyze actual samples. Therefore, this proposed strategy may be established as a useful and practical platform for the ultrasensitive detection of mycotoxins in food safety testing.

Quantum bead-based fluorescence-linked immunosorbent assay for ultrasensitive detection of aflatoxin M1 in pasteurized milk, yogurt, and milk powder

Herein, we reported a novel direct competitive fluorescence-linked immunosorbent assay (dcFLISA) for the ultrasensitive detection of aflatoxin M₁ (AFM₁) in pasteurized milk, yogurt, and milk powder using 150-nm quantum dot beads (QB) as the carrier of competing antigen. Large QB were applied to decrease the binding affinity of the competing antigen to antibody and enhance the fluorescent signal intensity. The aflatoxin B₁ molecule was used as the surrogate of AFM₁ to label with BSA on the surface of QB because of its 63% cross reaction to anti-AFM₁ mAb. The binding affinity of the competing antigen to mAb was tuned by changing the labeled molar ratios of aflatoxin B₁ to BSA. Through combining the advantages of QB as the carrier of the competing antigen, including low binding affinity to mAb and highly fluorescent signal output, the proposed dcFLISA exhibited an ultrahigh sensitivity for AFM₁ detection, with a half-maximal inhibitory concentration of 3.15 pg/mL in 0.01 M phosphate-buffered saline solution (pH 7.4), which is substantially lower than that of the traditional horseradish peroxidase-based ELISA. The proposed method also exhibited very low detection limitations of 0.5, 0.6, and 0.72 pg/mL for real pasteurized milk, yogurt, and milk powder, respectively. These values are considerably below the maximum permissible level of the European Commission standard for AFM₁ in dairy products. In summary, the proposed dcFLISA offers a novel strategy with an ultrahigh sensitivity for the routine monitoring of AFM₁ in various dairy products.

A multiplexed FRET aptasensor for the simultaneous detection of mycotoxins with magnetically controlled graphene oxide/Fe3O4 as a single energy acceptor

A multiplexed FRET aptasensor was developed for the simultaneous detection of AFB1 and FB1 with magnetically controlled GO/Fe₃O₄ as a single energy acceptor.