Self-assembled monolayers (SAMs) for electrochemical sensing

An electrochemical proximity assay (ECPA) for antibody detection incorporating flexible spacers for improved performance

A clever approach for biosensing is to leverage the concept of the proximity effect, where analyte binding to probes can be coupled to a second, controlled binding event such as short DNA strands. This analyte-dependent effect has been exploited in various sensors with optical or electrochemical readouts. Electrochemical proximity assays (ECPA) are more amenable to miniaturization and adaptation to the point-of-care, yet ECPA has been generally targeted toward protein sensing with antibody-oligonucleotide probes. Antibodies themselves are also important as biomarkers, since they are produced in bodily fluids in response to various diseases or infections, often in low amounts. In this work, by using antigen-DNA conjugates, we targeted an ECPA method for antibody sensing and showed that the assay performance can be greatly enhanced using flexible spacers in the DNA conjugates. After adding flexible polyethylene glycol (PEG) spacers at two distinct positions, the spacers ultimately increased the antibody-dependent current by a factor of 4.0 without significant background increases, similar to our recent work using thermofluorimetric analysis (TFA). The optimized ECPA was applied to anti-digoxigenin antibody quantification at concentrations ranging over two orders of magnitude, from the limit of detection of 300 pM up to 50 nM. The assay was functional in 90% human serum, where increased ionic strength was used to counteract double-layer repulsion effects at the electrode. This flexible-probe ECPA methodology should be useful for sensing other antibodies in the future with high sensitivity, and the mechanism for signal improvement with probe flexibility may be applicable to other DNA-based electrochemical sensor platforms.

Energetics and Redox Kinetics of Pure Ferrocene-Terminated N-Heterocyclic Carbene Self-Assembled Monolayers on Gold

N-heterocyclic carbene (NHC) self-assembled monolayers (SAMs) on gold have received considerable attention, but little is known about the lateral interactions between neighboring NHC molecules, their stability when subjected to aggressive oxidizing/reducing conditions, and their interactions with solution ions, all of which are essential for their use in a wide range of applications. To address these deficiencies, we present a comprehensive investigation of two different ferrocene (Fc)-terminated NHC SAMs with different chain lengths and linking groups. Pure monolayers of Fc-terminated NHCs display only a single, symmetrical pair of redox peaks, implying the formation of a homogeneous SAM structure with uniformly distributed Fc/Fc+ redox centers. By comparison, pure Fc-alkylthiol SAMs exhibit complex and impractical redox chemistry and require surface dilution in order to achieve reproducible properties. The NHC SAMs examined in this study exhibit very fast Fc redox kinetics and comparable or even superior stability against the application of multiple potential cycles or long-time holding at constant potential compared to alkylthiol SAMs. Furthermore, ion pairing of Fc+ and hydrophobic perchlorate and other hydrophilic anions is observed with Fc-NHC SAMs, highlighting conditions favorable for future applications of these monolayers. This study should therefore shed light on the very promising characteristics of redox-active NHC SAMs as an alternative to traditional Fc-alkylthiol SAMs for multiple practical applications, including in sensors and electrocatalysis.

Schottky Diode Leakage Current Fluctuations: Electrostatically Induced Flexoelectricity in Silicon

Nearly four decades have passed since IBM scientists pioneered atomic force microscopy (AFM) by merging the principles of a scanning tunneling microscope with the features of a stylus profilometer. Today, electrical AFM modes are an indispensable asset within the semiconductor and nanotechnology industries, enabling the characterization and manipulation of electrical properties at the nanoscale. However, electrical AFM measurements suffer from reproducibility issues caused, for example, by surface contaminations, Joule heating, and hard-to-minimize tip drift and tilt. Using as experimental system nanoscale Schottky diodes assembled on oxide-free silicon crystals of precisely defined surface chemistry, it is revealed that voltage-dependent adhesion forces lead to significant rotation of the AFM platinum tip. The electrostatics-driven tip rotation causes a strain gradient on the silicon surface, which induces a flexoelectric reverse bias term. This directional flexoelectric internal-bias term adds to the external (instrumental) bias, causing both an increased diode leakage as well as a shift of the diode knee voltage to larger forward biases. These findings will aid the design and characterization of silicon-based devices, especially those that are deliberately operated under large strain or shear, such as in emerging energy harvesting technologies including Schottky-based triboelectric nanogenerators (TENGs).

Stimuli-Responsive Oligourea Molecular Films

We have designed and synthesized a helical cysteamine-terminated oligourea foldamer composed of ten urea residues featuring side carboxyl and amine groups. The carboxyl group is located in proximity to the C-terminus of the oligourea and hence at the negative pole of the helix dipole. The amine group is located close to the N-terminus and hence at the positive pole of the helix dipole. Beyond the already remarkable dipole moment inherent in oligourea 2.5 helices, the incorporation of additional charges originating from the carboxylic and amine groups is supposed to impact the overall charge distribution along the molecule. These molecules were self-assembled into monolayers on a gold substrate, allowing us to investigate the influence of an electric field on these polar helices. By applying surface-enhanced infrared reflection-absorption spectroscopy, we proved that molecules within the monolayers tend to reorient themselves more vertically when a negative bias is applied to the surface. It was also found that surface-confined oligourea molecules affected by the external electric field tend to rearrange the electron density at urea groups, leading to the stabilization of the resonance structure with charge transfer character. The presence of the external electric field also affected the nanomechanical properties of the oligourea films, suggesting that molecules also tend to reorient in the ambient environment without an electrolyte solution. Under the same conditions, the helical oligourea displayed a robust piezoresponse, particularly noteworthy given the slender thickness of the monolayer, which measured approximately 1.2 nm. This observation demonstrates that thin molecular films composed of oligoureas may exhibit stimulus-responsive properties. This, in turn, may be used in nanotechnology systems as actuators or functional films, enabling precise control of their thickness in the range of even fractions of nanometers.

A Current Averaging Strategy for Maximizing Analyte and Minimizing Redox Interference Signals with Square Wave Voltammetry

Square wave voltammetry (SWV) is commonly used in electroanalytical applications to enhance analyte faradaic signals and minimize nonfaradaic processes. However, little attention is given as to how best use SWV to minimize faradaic interference signals that arise from redox species present in solution that have redox potentials that convolute with that of the analyte. In conventional SWV, a series of current-time (i-t) transients are collected, and i is averaged over a specified window of each transient (potentiostat dependent). This average i is reported against the electrode potential, E. As the i-t response is governed by the type of electron transfer reaction under investigation, we show how by collecting all i-t data and through judicious choice of the current averaging window, it is possible to enhance the analyte response while at the same time reducing the interferent signal. We look at three different electron transfer reactions, fast electron transfer outer sphere, metal electrodeposition/stripping, and surface-confined proton-coupled electron transfer (PCET) and demonstrate different i-t behaviors in SWV, visually aided by the use of 3D i-t-E plots. In the case of PCET quinone-based voltammetric sensing of pH in the presence of a heavy metal (here Cu2+), we show that the use of a much earlier current averaging window (2-10% of the i-t response) results in the pH signal being clearly distinguished from that of the overlapping heavy metal.

Spectroelectrochemical determination of thiolate self-assembled monolayer adsorptive stability in aqueous and non-aqueous electrolytes

Self-assembled monolayers (SAM) are ubiquitous in studies of modified electrodes for sensing, electrocatalysis, and environmental and energy applications. However, determining their adsorptive stability is crucial to ensure robust experiments. In this work, the stable potential window (SPW) in which a SAM-covered electrode can function without inducing SAM desorption was determined for aromatic SAMs on gold electrodes in aqueous and non-aqueous solvents. The SPWs were determined by employing cyclic voltammetry, attenuated total reflectance surface-enhanced infrared absorption spectroscopy (ATR-SEIRAS), and surface plasmon resonance (SPR). The electrochemical and spectroscopic findings concluded that all the aromatic SAMs used displayed similar trends and SPWs. In aqueous systems, the SPW lies between the reductive desorption and oxidative desorption, with pH being the decisive factor affecting the range of the SPW, with the widest SPW observed at pH 1. In the non-aqueous electrolytes, the desorption of SAMs was observed to be slow and progressive. The polarity of the solvent was the main factor in determining the SPW. The lower the polarity of the solvent, the larger the SPW, with 1-butanol displaying the widest SPW. This work showcases the power of spectroelectrochemical analysis and provides ample future directions for the use of non-polar solvents to increase SAM stability in electrochemical applications.

Combining plasmonic and electrochemical biosensing methods

The idea of combining electrochemical (EC) and plasmonic biosensor methods was introduced almost thirty years ago and the potential of electrochemical-plasmonic (EC-P) biosensors has been highlighted ever since. Despite that, the use of EC-P biosensors in analytics has been rather limited so far and the search for unique applications of the EC-P method continues. In this paper, we review the advances in the field of EC-P biosensors and discuss the features and benefits they can provide. In addition, we identify the main challenges for the development of EC-P biosensors and the limitations that prevent EC-P biosensors from more widespread use. Finally, we review applications of EC-P biosensors for the investigation and quantification of biomolecules, and for the study of biomolecular and cellular processes.

Codeposition Enhances the Performance of Electrochemical Aptamer-Based Sensors

Electrochemical aptamer-based (EAB) sensors, a minimally invasive means of performing high-frequency, real-time measurement of drugs and biomarkers in situ in the body, have traditionally been fabricated by depositing their target-recognizing aptamer onto an interrogating gold electrode using a "sequential" two-step method involving deposition of the thiol-modified oligonucleotide (typically for 1 h) followed by incubation in mercaptohexanol solution (typically overnight) to complete the formation of a stable, self-assembled monolayer. Here we use EAB sensors targeting vancomycin, tryptophan, and phenylalanine to show that "codeposition", a less commonly employed EAB fabrication method in which the thiol-modified aptamer and the mercaptohexanol diluent are deposited on the electrode simultaneously and for as little as 1 h, improves the signal gain (relative change in signal upon the addition of high concentrations of the target) of the vancomycin and tryptophan sensors without significantly reducing their stability. In contrast, the gain of the phenylalanine sensor is effectively identical irrespective of the fabrication approach employed. This sensor, however, appears to employ binding-induced displacement of the redox reporter rather than binding-induced folding as its signal transduction mechanism, suggesting in turn a mechanism for the improvement observed for the other two sensors. Codeposition thus not only provides a more convenient means of fabricating EAB sensors but also can improve their performance.

Surface Modification of Screen-Printed Carbon Electrode through Oxygen Plasma to Enhance Biosensor Sensitivity

The screen-printed carbon electrode (SPCE) is a useful technology that has been widely used in the practical application of biosensors oriented to point-of-care testing (POCT) due to its characteristics of cost-effectiveness, disposability, miniaturization, wide potential window, and simple electrode design. Compared with gold or platinum electrodes, surface modification is difficult because the carbon surface is chemically or physically stable. Oxygen plasma (O2) can easily produce carboxyl groups on the carbon surface, which act as scaffolds for covalent bonds. However, the effect of O2-plasma treatment on electrode performance remains to be investigated from an electrochemical perspective, and sensor performance can be improved by clarifying the surface conditions of plasma-treated biosensors. In this research, we compared antibody modification by plasma treatment and physical adsorption, using our novel immunosensor based on gold nanoparticles (AuNPs). Consequently, the O2-plasma treatment produced carboxyl groups on the electrode surface that changed the electrochemical properties owing to electrostatic interactions. In this study, we compared the following four cases of SPCE modification: O2-plasma-treated electrode/covalent-bonded antibody (a); O2-plasma-treated electrode/physical adsorbed antibody (b); bare electrode/covalent-bonded antibody (c); and bare electrode/physical absorbed antibody (d). The limits of detection (LOD) were 0.50 ng/mL (a), 9.7 ng/mL (b), 0.54 ng/mL (c), and 1.2 ng/mL (d). The slopes of the linear response range were 0.039, 0.029, 0.014, and 0.022. The LOD of (a) was 2.4 times higher than the conventional condition (d), The slope of (a) showed higher sensitivity than other cases (b~d). This is because the plasma treatment generated many carboxyl groups and increased the number of antibody adsorption sites. In summary, the O2-plasma treatment was found to modify the electrode surface conditions and improve the amount of antibody modifications. In the future, O2-plasma treatment could be used as a simple method for modifying various molecular recognition elements on printed carbon electrodes.

Self-Assembled Monolayers of a Fluorinated Phosphonic Acid as a Protective Coating on Aluminum

Aluminum (Al) placed in hot water (HW) at 90 °C is roughened due to its reaction with water, forming Al hydroxide and Al oxide, as well as releasing hydrogen gas. The roughened surface is thus hydrophilic and possesses a hugely increased surface area, which can be useful in applications requiring hydrophilicity and increased surface area, such as atmospheric moisture harvesting. On the other hand, when using HW to roughen specified areas of an Al substrate, ways to protect the other areas from HW attacks are necessary. We demonstrated that self-assembled monolayers (SAMs) of a fluorinated phosphonic acid (FPA, CF3(CF2)13(CH2)2P(=O)(OH)2) derivatized on the native oxide of an Al film protected the underneath metal substrate from HW attack. The intact wettability and surface morphology of FPA-derivatized Al subjected to HW treatment were examined using contact angle measurement, and scanning electron microscopy and atomic force microscopy, respectively. Moreover, the surface and interface chemistry of FPA-derivatized Al before and after HW treatment were investigated by time-of-flight secondary ion mass spectrometry (ToF-SIMS), verifying that the FPA SAMs were intact upon HW treatment. The ToF-SIMS results therefore explained, on the molecular level, why HW treatment did not affect the underneath Al at all. FPA derivatization is thus expected to be developed as a patterning method for the formation of hydrophilic and hydrophobic areas on Al when combined with HW treatment.

The Cleanroom-Free, Cheap, and Rapid Fabrication of Nanoelectrodes with Low zM Limits of Detection

Nanoscale electrodes have been a topic of intense research for many decades. Their enhanced sensitivities, born out of an improved signal-to-noise ratio as electrode dimensions decrease, make them ideal for the development of low-concentration analyte sensors. However, to date, nanoelectrode fabrication has typically required expensive equipment and exhaustive, time-consuming fabrication methods that have rendered them unsuitable for widespread use and commercialization. Herein, a method of nanoband electrode fabrication using low cost materials and equipment commonly found in research laboratories around the world is reported. The materials' cost to produce each nanoband is less than €0.01 and fabrication of a batch takes less than 1 h. The devices can be made of flexible plastics and their designs can be quickly and easily iterated. Facile methods of combining these nanobands into powerful devices, such as complete three-electrode systems, are also displayed. As a proof of concept, the electrodes are functionalized for the detection of a DNA sequence specific to SARS-CoV-2 and found to display single molecule sensitivity.

Impact of nanotechnology on progress of flow methods in chemical analysis: A review

In evolution of instrumentation for analytical chemistry as crucial technological breakthroughs should be considered a common introduction of electronics with all its progress in integration, and then microprocessors which was followed by a widespread computerization. It is seems that a similar role can be attributed to the introduction of various elements of modern nanotechnology, observed with a fast progress since beginning of this century. It concerns all areas of the applications of analytical chemistry, including also progress in flow analysis, which are being developed since the middle of 20th century. Obviously, it should not be omitted the developed earlier and analytically applied planar structures like lipid membranes or self-assembled monolayers They had essential impact prior to discoveries of numerous extraordinary nanoparticles such as fullerenes, carbon nanotubes and graphene, or nanocrystalline semiconductors (quantum dots). Mostly, due to catalytic effects, significantly developed surface and the possibility of easy functionalization, their application in various stages of flow analytical procedures can significantly improve them. The application of new nanomaterials may be used for the development of new detection methods for flow analytical systems in macro-flow setups as well as in microfluidics and lateral flow immunoassay tests. It is also advantageous that quick flow conditions of measurements may be helpful in preventing unfavorable agglomeration of nanoparticles. A vast literature published already on this subject (e.g. almost 1000 papers about carbon nanotubes and flow-injection analytical systems) implies that for this reviews it was necessary to make an arbitrary selection of reported examples of this trend, focused mainly on achievements reported in the recent decade.

Detection of Aromatic Hydrocarbons in Aqueous Solutions Using Quartz Tuning Fork Sensors Modified with Calix[4]arene Methoxy Ester Self-Assembled Monolayers: Experimental and Density Functional Theory Study

Quartz tuning forks (QTFs), which were coated with gold and with self-assembled monolayers (SAM) of a lower-rim functionalized calix[4]arene methoxy ester (CME), were used for the detection of benzene, toluene, and ethylbenzene in water samples. The QTF device was tested by measuring the respective frequency shifts obtained using small (100 µL) samples of aqueous benzene, toluene, and ethylbenzene at four different concentrations (10-12, 10-10, 10-8, and 10-6 M). The QTFs had lower limits of detection for all three aromatic hydrocarbons in the 10-14 M range, with the highest resonance frequency shifts (±5%) being shown for the corresponding 10-6 M solutions in the following order: benzene (199 Hz) > toluene (191 Hz) > ethylbenzene (149 Hz). The frequency shifts measured with the QTFs relative to that in deionized water were inversely proportional to the concentration/mass of the analytes. Insights into the effects of the alkyl groups of the aromatic hydrocarbons on the electronic interaction energies for their hypothetical 1:1 supramolecular host-guest binding with the CME sensing layer were obtained through density functional theory (DFT) calculations of the electronic interaction energies (ΔIEs) using B3LYP-D3/GenECP with a mixed basis set: LANL2DZ and 6-311++g(d,p), CAM-B3LYP/LANL2DZ, and PBE/LANL2DZ. The magnitudes of the ΔIEs were in the following order: [Au4-CME⊃[benzene] > [Au4-CME]⊃[toluene] > [Au4-CME]⊃[ethylbenzene]. The gas-phase BSSE-uncorrected ΔIE values for these complexes were higher, with values of -96.86, -87.80, and -79.33 kJ mol-1, respectively, and -86.39, -77.23, and -67.63 kJ mol-1, respectively, for the corresponding BSSE-corrected values using B3LYP-D3/GenECP with LANL2dZ and 6-311++g(d,p). The computational findings strongly support the experimental results, revealing the same trend in the ΔIEs for the proposed hypothetical binding modes between the tested analytes with the CME SAMs on the Au-QTF sensing surfaces.

Electrochemical and Bioelectrochemical Sensing Platforms for Diagnostics of COVID-19

Rapid transmission and high mortality rates caused by the SARS-CoV-2 virus showed that the best way to fight against the pandemic was through rapid, accurate diagnosis in parallel with vaccination. In this context, several research groups around the world have endeavored to develop new diagnostic methods due to the disadvantages of the gold standard method, reverse transcriptase polymerase chain reaction (RT-PCR), in terms of cost and time consumption. Electrochemical and bioelectrochemical platforms have been important tools for overcoming the limitations of conventional diagnostic platforms, including accuracy, accessibility, portability, and response time. In this review, we report on several electrochemical sensors and biosensors developed for SARS-CoV-2 detection, presenting the concepts, fabrication, advantages, and disadvantages of the different approaches. The focus is devoted to highlighting the recent progress of electrochemical devices developed as next-generation field-deployable analytical tools as well as guiding future researchers in the manufacture of devices for disease diagnosis.

Disordered Mixture of Self-Assembled Molecular Functional Groups on Heterointerfaces with p-Si Leads to Multiple Key Generation in Physical Unclonable Functions

Physical unclonable function (PUF) security devices based on hardware are becoming an effective strategy to overcome the dependency of the internet cloud and software-based hacking vulnerabilities. On the other hand, existing Si-based artificial security devices have several issues, including the absence of a method for multiple key generation, complex and expensive fabrication processes, and easy prediction compared to devices retaining natural randomness. Herein, to generate unique and unpredictable multiple security keys, this paper proposes novel PUF devices consisting of a disordered random mixture of two self-assembled monolayers (SAMs) formed onto p-type Si. The proposed PUF devices exhibited multikeys at different voltage biasing, including 0 V, through the arbitrary dipole effect. As a result, multiple unpredictable hardware security keys were generated from one device using a simple solution-coating process. The PUF security device based on the mixture of materials with different dipoles developed in this study can provide valuable insights for implementing various PUF devices in the future.

Impedimetric Bacterial Detection Using Random Antimicrobial Peptide Mixtures

The biosensing of bacterial pathogens is of a high priority. Electrochemical biosensors are an important future tool for rapid bacteria detection. A monolayer of bacterial-binding peptides can serve as a recognition layer in such detection devices. Here, we explore the potential of random peptide mixtures (RPMs) composed of phenylalanine and lysine in random sequences and of controlled length, to form a monolayer that can be utilized for sensing. RPMs were found to assemble in a thin and diluted layer that attracts various bacteria. Faradaic electrochemical impedance spectroscopy was used with modified gold electrodes to measure the charge-transfer resistance (RCT) caused due to the binding of bacteria to RPMs. Pseudomonas aeruginosa was found to cause the most prominent increase in RCT compared to other model bacteria. We show that the combination of highly accessible antimicrobial RPMs and electrochemical analysis can be used to generate a new promising line of bacterial biosensors.

Covalent Grafting of Dielectric Films on Cu(111) Surface via Electrochemical Reduction of Aryl Diazonium Salts

Covalent grafting of dielectric films containing polyhedral oligomeric silsesquioxane (POSS) on the surface of Cu(111) is performed by a one-step electrochemical reduction of diazonium salts. This method is efficient and economic and performs in a proton-polar solvent of deionized water and tetrahydrofuran (THF), where the monomer employs an octavinylsilsesquioxane (OVS) containing a POSS core. The eight vinyl bonds contained in OVS are used to participate in aryl radical-initiated polymerization reactions to form films. The formed film is dense and covers the copper surface completely and uniformly. The thickness of the film can be controlled by adjusting the reaction time. The components of the films are mainly polynitrophenyl (PNP) or polyaminophenyl (PAP) as well as poly(octavinylsilsesquioxane) (POVS), and the POVS content could be adjusted by the applied voltage. The introduction of POSS prevents the copper surface from being oxidized and often gives the film good properties such as good dielectric properties, mechanical properties, and thermal properties. In addition, the presence of Cu-O-C and Cu-C bonds between the film and copper interface is confirmed at different film thicknesses by X-ray photoelectron spectroscopy (XPS), which allowed the construction of covalent bonds between metal and nonmetal, further enhancing the bonding between the film and copper. Organic films prepared by electrochemical reduction of diazonium salts using OVS as a monomer will have potential significance for the future development of the electronics industry.

Label-free electrochemical immunosensor for picomolar detection of the cervical cancer biomarker MCM5

An immunosensor for label-free electrochemical detection of MiniChromosome Maintenance Protein 5, MCM5, a protein overexpressed in cervical cancer, based on a gold electrode is reported. The electrode was first modified with a submonolayer (capture layer) of 11-mercaptoundecanoic acid (11-MUA) and then activated with N-(3-dimethylaminopropyl)-N-ethylcarbodiimide hydrochloride (EDC) and N-hydroxysuccinimide (NHS) to immobilize the capture antibody. The change in electrode surface properties (wettability) during the formation of the 11-MUA layers was determined using the static water contact angle (WCA). The binding of MCM5 antigens to the capture antibody was monitored by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) using 5 mM [Fe(CN)⁶]^3-/4- in 0.1 M LiClO₄(aq) as an electroactive probe. AC Impedance was used to measure charge transfer resistance (R_ct), which reflects impeded electron transfer when the antigen is bound to the antibody functionalized surface. After exposing the antibody-functionalized surface to MCM5 antigens, R_ct increases linearly with the logarithmic value of MCM5 antigen concentration, with a linear dynamic range of 10^-6 to 10^-11 g/mL, a correlation coefficient of 0.99, and a detection limit of 2.9 pM (10^-11 g/mL). This excellent sensitivity was achieved with simple preparation steps and minimal reagent consumption, without the need for complicated procedures such as enzymatic amplification, fluorescent labeling, or nanoparticle modification.

Finite Element Modeling of the Combined Faradaic and Electrostatic Contributions to the Voltammetric Response of Monolayer Redox Films

The voltammetric response of electrodes coated with a redox-active monolayer is computed by finite element simulations based on a generalized model that couples the Butler-Volmer, Nernst-Planck, and Poisson equations. This model represents the most complete treatment of the voltammetric response of a redox film to date and is made accessible to the experimentalist via the use of finite element modeling and a COMSOL-generated report. The model yields a full description of the electric potential and charge distributions across the monolayer and bulk solution, including the potential distribution associated with ohmic resistance. In this way, it is possible to properly account for electrostatic effects at the molecular film/electrolyte interface, which are present due to the changing charge states of the redox head groups as they undergo electron transfer, under both equilibrium and nonequilibrium conditions. Specifically, our numerical simulations significantly extend previous theoretical predictions by including the effects of finite electron-transfer rates (k⁰) and electrolyte conductivity. Distortion of the voltammetric wave due to ohmic potential drop is shown to be a function of electrolyte concentration and scan rate, in agreement with experimental observations. The commonly used Laviron analysis for the determination of k⁰ fails to account for ohmic drop effects, which may be non-negligible at high scan rates. This model provides a more accurate alternative for k⁰ determination at all scan rates. The electric potential and charge distributions across an electrochemically inactive monolayer and electrolyte solution are also simulated as a function of applied potential and are found to agree with the Gouy-Chapman-Stern theory.

Sensors for Volatile Organic Compounds

This paper provides an overview of recent developments in the field of volatile organic compound (VOC) sensors, which are finding uses in healthcare, safety, environmental monitoring, food and agriculture, oil industry, and other fields. It starts by briefly explaining the basics of VOC sensing and reviewing the currently available and quickly progressing VOC sensing approaches. It then discusses the main trends in materials' design with special attention to nanostructuring and nanohybridization. Emerging sensing materials and strategies are highlighted and their involvement in the different types of sensing technologies is discussed, including optical, electrical, and gravimetric sensors. The review also provides detailed discussions about the main limitations of the field and offers potential solutions. The status of the field and suggestions of promising directions for future development are summarized.

Electrochemical biosensor with aptamer/porous platinum nanoparticle on round-type micro-gap electrode for saxitoxin detection in fresh water

Cyanotoxins are toxins produced by cyanobacteria; they negatively impact water resources used by humans and disrupt ecosystems worldwide. Among cyanotoxins, saxitoxin (STX) is a small molecule that causes paralysis in humans and contamination in freshwater resources. To monitor low concentration of STX levels, a sensitive and high fidelity detection system is required. In this study, a round-type micro-gap electrode (RMGE) was fabricated that provides the high signal fidelity for STX detection in real freshwater sample. The RMGE has the 15 pairs of identical electrode wire length between gap that gives the high signal fidelity. In addition, the sensitivity for STX detection was improved by introducing the porous platinum nanoparticle (pPtNP) that enahced the electrochemical sensitivity and the STX aptamer was used as the bioprobe. An electrochemical measurement method (square wave voltammetry (SWV) and electrochemical impedance spectroscopy (EIS)) was introduced to construct STX biosensor. To evaluate the biosensor performance, the limit of detection (LOD) and selectivity test were performed on real freshwater samples. The biosensor demonstrated high selectivity even in freshwater samples over a wide linear concentration range of 10 pg/mL to 1 μg/mL and a detection limit of 4.669 pg/mL. These results suggest that the designed biosensor shows a wide range of possibilities for the detection of toxicants in freshwater that provide the new direction to the biosensor electrode design.

Multi-Oxyanion Detection by an Organic Field-Effect Transistor with Pattern Recognition Techniques and Its Application to Quantitative Phosphate Sensing in Human Blood Serum

We herein report an organic field-effect transistor (OFET) based chemical sensor for multi-oxyanion detection with pattern recognition techniques. The oxyanions ubiquitously play versatile roles in biological systems, and accessing the chemical information they provide would potentially facilitate fundamental research in diagnosis and pharmacology. In this regard, phosphates in human blood serum would be a promising indicator for early case detection of significant diseases. Thus, the development of an easy-to-use chemical sensor for qualitative and quantitative detection of oxyanions is required in real-world scenarios. To this end, an extended-gate-type OFET has been functionalized with a metal complex consisting of 2,2'-dipicolylamine and a copper(II) ion (CuII-dpa), allowing a compact chemical sensor for oxyanion detection. The OFET combined with a uniform CuII-dpa-based self-assembled monolayer (SAM) on the extended-gate gold electrode shows a cross-reactive response, which suggests a discriminatory power for pattern recognition. Indeed, the qualitative detection of 13 oxyanions (i.e., hydrogen monophosphate, pyrophosphate, adenosine monophosphate, adenosine diphosphate, adenosine triphosphate, terephthalate, phthalate, isophthalate, malonate, oxalate, lactate, benzoate, and acetate) has been demonstrated by only using a single OFET-based sensor with linear discriminant analysis, which has shown 100% correct classification. The OFET has been further applied to the quantification of hydrogen monophosphate in human blood serum using a support vector machine (SVM). The multiple predictions of hydrogen monophosphate at 49 and 89 μM have been successfully realized with low errors, which indicates that the OFET-based sensor with pattern recognition techniques would be a practical sensing platform for medical assays. We believe that a combination of the OFET functionalized with the SAM-based recognition scaffold and powerful pattern recognition methods can achieve multi-analyte detection from just a single sensor.

Surface Bonding Enhanced Self-Co-Reactant Electrogenerated Chemiluminescence for Sensitive and Selective Detection of Thioglycolic Acid in Cosmetics

Thioglycolic acid (TGA) is an organic compound widely used in cosmetics that cause a variety of health problems when overexposed to it. So far many attempts have been made to develop methods for TGA detection, but most of them need sophisticated instrumentations and are a little bit complicated. Therefore, a simple, cheap and sensitive detection method of TGA is highly desired. Herein, we demonstrated for the first time an Au-S bonding amplified, highly sensitive electrochemiluminescence (ECL) sensing method for TGA detection using tris(2,2'-bipyridyl)ruthenium(II) (Ru(bpy) 3 2+ ) as a luminophore and TGA as a self-co-reactant, via an anodic reaction at the Au electrode surface. Due to different molecular coordination environments of the TGA at the electrode surface, the ECL signal intensity of the developed ECL system gives much higher ECL signal in borate buffer than phosphate buffer of the same pH. Under the optimized experimental conditions, the ECL intensity has a direct relationship with the concentration of TGA in the range of 0.03 μM to 300 μM and a limit of detection of 0.013 µM (3σ/ m ). The reported ECL system has further been applied for the detection of TGA in cosmetics with acceptable recoveries.

Surface chemical reactions on self-assembled silane based monolayers

In this review, we aim to update our review "Chemical modification of self-assembled silane-based monolayers by surface reactions" which was published in 2010 and has developed into an important guiding tool for researchers working on the modification of solid substrate surface properties by chemical modification of silane-based self-assembled monolayers. Due to the rapid development of this field of research in the last decade, the utilization of chemical functionalities in self-assembled monolayers has been significantly improved and some new processes were introduced in chemical surface reactions for tailoring the properties of solid substrates. Thus, it is time to update the developments in the surface functionalization of silane-based molecules. Hence, after a short introduction on self-assembled monolayers, this review focuses on a series of chemical reactions, i.e., nucleophilic substitution, click chemistry, supramolecular modification, photochemical reaction, and other reactions, which have been applied for the modification of hydroxyl-terminated substrates, like silicon and glass, which have been reported during the last 10 years.

Characterizing Chelation at Surfaces by Charge Tunneling

This paper describes a surface analysis technique that uses the "EGaIn junction" to measure tunneling current densities (J(V), amps/cm²) through self-assembled monolayers (SAMs) terminated in a chelating group and incorporating different transition metal ions. Comparisons of J(V) measurements between bare chelating groups and chelates are used to characterize the composition of the SAM and infer the dissociation constant (K_d, mol/L), as well as kinetic rate constants (k_off, L/mol·s; k_on, 1/s) of the reversible chelate-metal reaction. To demonstrate the concept, SAMs of 11-(4-methyl-2,2'-bipyrid-4'-yl (bpy))undecanethiol (HS(CH₂)₁₁bpy) were incubated within ethanol solutions of metal salts. After rinsing and drying the surface, measurements of current as a function of incubation time and concentration in solution are used to infer k_off, k_on, and K_d. X-ray photoelectron spectroscopy (XPS) provides an independent measure of surface composition to confirm inferences from J(V) measurements. Our experiments establish that (i) bound metal ions are stable to the rinsing step as long as the rinsing time, τ_rinse ≪ 1koff; (ii) the bound metal ions increase the current density at the negative bias and reduce the rectification observed with free bpy terminal groups; (iii) the current density as a function of the concentration of metal ions in solution follows a sigmoidal curve; and (iv) the values of K_d measured using J(V) are comparable to those measured using XPS, but larger than those measured in solution. The EGaIn junction, thus, provides a new tool for the analysis of the composition of the surfaces that undergo reversible chemical reactions with species in solution.

Simulations of X-ray absorption spectroscopy and energetic conformation of N-heterocyclic carbenes on Au(111)

It has recently been demonstrated that N-heterocyclic carbenes (NHCs) form self-assembled monolayers (SAMs) on metal surfaces. Consequently, it is important to both characterize and understand their binding modes to fully exploit NHCs in functional surface systems. To assist with this effort, we have performed first-principles total energy calculations for NHCs on Au(111) and simulations of X-ray absorption near edge structure (XANES). The NHCs we have considered are N,N-dimethyl-, N,N-diethyl-, N,N-diisopropylbenzimidazolylidene (BNHCX, with X = Me, Et, and iPr, respectively) and the bis-BNHCX-Au complexes derived from these molecules. We present a comprehensive analysis of the energetic stability of both the BNHCX and the complexes on Au(111) and, for the former, examine the role of the wing group in determining the attachment geometry. Further structural characterization is performed by calculating the nitrogen K-edge X-ray absorption spectra. Our simulated XANES results give insight into (i) the relationship between the BNHCX/Au geometry and the N(1s) → π*/σ*, pre-edge/near-edge, absorption intensities, and (ii) the contributions of the molecular deformation and molecule-surface electronic interaction to the XANES spectrum. These simulated spectra work not only as a map to the BNHCX conformation, but also, combined with electronic structure calculations, provide a clear understanding of recent experimental XANES findings on BNHCX/Au.

Self-assembled monolayer formation of pentamers-like molecules onto FCC(111) surfaces: the case of curcuminoids onto Au(111) surface

The adsorption of rigid straight electrically polarized pentamers over a FCC(111) surface is studied. The model was inspired by the deposition of 2-thiophene molecules over the Au(111) surface, which was previously characterized by experimental techniques and simulated under the frame of the density functional theory. We now obtain and report the charge distribution of the molecule which allows to propose a deposition model followed by Monte Carlo simulations over an ad-hoc lattice gas model. We show that for a certain value of the chemical potential there exists an isotropic-nematic phase transition which can explain the formation of a self-assembled monolayer like the one observed in the transmission electron microscopy images. An order parameter is defined to characterize the transition which presents a step-like behavior at a critical chemical potential value. The possible nature of the nematic transition in conjunction with an ergodicity breakdown is discussed as future work by means of statistical physics techniques.

Screen Printed Based Impedimetric Immunosensor for Rapid Detection of Escherichia coli in Drinking Water

The development of a simple and low cost electrochemical impedance immunosensor based on screen printed gold electrode for rapid detection of Escherichia coli in water is reported. The immunosensor is fabricated by immobilizing anti-E. coli antibodies onto a gold surface in a covalent way by the photochemical immobilization technique, a simple procedure able to bind antibodies upright onto gold surfaces. Impedance spectra are recorded in 0.01 M phosphate buffer solution (PBS) containing 10 mM Fe(CN)₆³⁻/Fe(CN)₆⁴⁻ as redox probe. The Nyquist plots can be modelled with a modified Randles circuit, identifying the charge transfer resistance R_ct as the relevant parameter after the immobilization of antibodies, the blocking with BSA and the binding of E. coli. The introduction of a standard amplification procedure leads to a significant enhancement of the impedance increase, which allows one to measure E. coli in drinking water with a limit of detection of 3 × 10¹ CFU mL⁻¹ while preserving the rapidity of the method that requires only 1 h to provide a “yes/no” response. Additionally, by applying the Langmuir adsorption model, we are able to describe the change of R_ct in terms of the “effective” electrode, which is modified by the detection of the analyte whose microscopic conducting properties can be quantified.

A novel electrochemical sensor based on carbon nanotubes array for selective detection of dopamine or uric acid

A novel single-walled carbon nanotubes array-modified glassy carbon electrode (SWCNTs array-GCE) has been fabricated through a simple electrochemical technique. Benefitting from their vertically aligned configuration on the electrode surface, the modified single-walled carbon nanotubes can be used more efficiently in comparison with other modified method. The as-fabricated SWCNTs array-GCE can separate the anodic oxidation potential of dopamine (DA), uric acid (UA) and ascorbic acid (AA) with well-defined peak separation in the presence of each other, and thus employs as a new electrochemical sensor for selective determination of DA and UA. It can make a further improvement of the electrocatalytic ability of the electrode to perform an acetone pretreatment to SWCNTs array-GCE before electrochemical detection, which has been confirmed by atomic force microscope and electrochemical impedance spectroscopic measurements. Especially, unlike other carbon nanotubes-based electrode at which only two redox pairs are observed for dopamine oxidations, a third two-electron oxidation of 5,6-dihydroxyindole to indole-5,6-quinone can be clearly observed at acetone-pretreated SWCNTs array-GCE, showing the excellent electrocatalytic performance of as-fabricated electrode toward dopamine. The practicability of SWCNTs array-GCE was evaluated for the selective detection of DA and UA in real sample solutions of human serum and urine. It revealed acceptable recovery results in the range of 94-104%, indicating that it might be a promising platform for further biosensor development.

N-Heterocyclic Carbenes in Materials Chemistry

N-Heterocyclic carbenes (NHCs) have become one of the most widely studied class of ligands in molecular chemistry and have found applications in fields as varied as catalysis, the stabilization of reactive molecular fragments, and biochemistry. More recently, NHCs have found applications in materials chemistry and have allowed for the functionalization of surfaces, polymers, nanoparticles, and discrete, well-defined clusters. In this review, we provide an in-depth look at recent advances in the use of NHCs for the development of functional materials.

Electrochemically driven interfacial halogen bonding on self-assembled monolayers for anion detection

The concept of anion detection via reversible electrochemically driven charge-assisted halogen bonding in solution was transferred on the surface.

Electrochemical behavior of inorganic–organic hybrid polyoxometalate ((Cys)3[PW12O40]) nanostructure self-assembled monolayer on polycrystalline gold electrode surfaces

The synergistic effect of HPW and Cys enhanced electrochemical activity of Au-(Cys)PW electrode.

Functionalization and passivation of ultrathin alumina films of defined sub-nanometer thickness with self-assembled monolayers

Instability of ultrathin surface oxides on alloys under environmental conditions can limit the opportunities for applications of these systems when the thickness control of the insulating oxide film is crucial for device performance. A procedure is developed to directly deposit self-assembled monolayers (SAM) from solvent onto substrates prepared under ultra-high vacuum conditions without exposure to air. As an example, rhenium photosensitizers functionalized with carboxyl linker groups are attached to ultrathin alumina grown on NiAl(1 1 0). The thickness change of the oxide layer during the SAM deposition is quantified by x-ray photoelectron spectroscopy and can be drastically reduced to one atomic layer. The SAM acts as a capping layer, stabilizing the oxide thin film under environmental conditions. Ultraviolet photoelectron spectroscopy elucidates the band alignment in the resulting heterostructure. The method for molecule attachment presented in this manuscript can be extended to a broad class of molecules vulnerable to pyrolysis upon evaporation and presents an elegant method for attaching molecular layers on solid substrates that are sensitive to air.

Probing functional self-assembled molecular architectures with solution/solid scanning tunnelling microscopy

Over the past two decades, solution/solid STM has made clear contributions to our fundamental understanding of the thermodynamic and kinetic processes that occur in molecular self-assembly at surfaces. As the field matures, we provide an overview of how solution/solid STM is emerging as a tool to elucidate and guide the use of self-assembled molecular systems in practical applications, focusing on small molecule device engineering, molecular recognition and sensing and electronic modification of 2D materials.

SPRi-Based Biosensing Platforms for Detection of Specific DNA Sequences Using Thiolate and Dithiocarbamate Assemblies

The framework of presented study covers the development and examination of the analytical performance of surface plasmon resonance-based (SPR) DNA biosensors dedicated for a detection of model target oligonucleotide sequence. For this aim, various strategies of immobilization of DNA probes on gold transducers were tested. Besides the typical approaches: chemisorption of thiolated ssDNA (DNA-thiol) and physisorption of non-functionalized oligonucleotides, relatively new method based on chemisorption of dithiocarbamate-functionalized ssDNA (DNA-DTC) was applied for the first time for preparation of DNA-based SPR biosensor. The special emphasis was put on the correlation between the method of DNA immobilization and the composition of obtained receptor layer. The carried out studies focused on the examination of the capability of developed receptors layers to interact with both target DNA and DNA-functionalized AuNPs. It was found, that the detection limit of target DNA sequence (27 nb length) depends on the strategy of probe immobilization and backfilling method, and in the best case it amounted to 0.66 nM. Moreover, the application of ssDNA-functionalized gold nanoparticles (AuNPs) as plasmonic labels for secondary enhancement of SPR response is presented. The influence of spatial organization and surface density of a receptor layer on the ability to interact with DNA-functionalized AuNPs is discussed. Due to the best compatibility of receptors immobilized via DTC chemisorption: 1.47 ± 0.4 · 10¹² molecules · cm^-2 (with the calculated area occupied by single nanoparticle label of ~132.7 nm²), DNA chemisorption based on DTCs is pointed as especially promising for DNA biosensors utilizing indirect detection in competitive assays.

Affinity Biosensors for Detection of Mycotoxins in Food

This chapter reviews recent achievements in methods of detection of mycotoxins in food. Special focus is on the biosensor technology that utilizes antibodies and nucleic acid aptamers as receptors. Development of biosensors is based on the immobilization of antibodies or aptamers onto various conventional supports like gold layer, but also on nanomaterials such as graphene oxide, carbon nanotubes, and quantum dots that provide an effective platform for achieving high sensitivity of detection using various physical methods, including electrochemical, mass sensitive, and optical. The biosensors developed so far demonstrate high sensitivity typically in subnanomolar limit of detection. Several biosensors have been validated in real samples. The sensitivity of biosensors is similar and, in some cases, even better than traditional analytical methods such as ELISA or chromatography. We believe that future trends will be focused on improving biosensor properties toward practical application in food industry.