Photocatalytic Degradation of Organic Pollutants in Wastewater

Investigating the Effect of Bi2MoO6/g-C3N4 Ratio on Photocatalytic Degradation of Sulfadiazine under Visible Light

In this study, a series of Bi2MoO6/g-C3N4 composites were prepared through a wet-impregnation method, and their photocatalytic properties were investigated for the degradation of sulfadiazine (SDZ) under visible light irradiation. Physical and chemical characterizations were carried out using X-ray diffraction (XRD), scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FT-IR), photoluminescence spectroscopy (PL), UV-vis diffuse reflectance spectra (UV-vis), and electrochemical impedance spectra (EIS). Compared to pure g-C3N4, the introduction of Bi2MoO6 significantly enhanced the visible light responsive photocatalytic activity, with the 1:32 Bi2MoO6/g-C3N4 composite exhibiting the highest photodegradation efficiency towards SDZ under visible light irradiation with a photocatalytic efficiency of 93.88% after 120 min of visible light irradiation. The improved photocatalytic activity can be attributed to the formation of a heterojunction between Bi2MoO6 and g-C3N4, which promotes the transfer of photogenerated electron-hole pairs, thereby elevating its photocatalytic activity. The results suggest that Bi2MoO6/g-C3N4 composites have potential application for the degradation of sulfonamides in aquatic environments.

Intensification of the photodegradation efficiency of an emergent water pollutant through process conditions optimization by means of response surface methodology

Heterogeneous photocatalysis has been increasingly investigated during the past years and has been recognized as a promising technique for clean and safe water purification. The current study exploits the advantage of this technique demonstrating that the removal of a biorefractory water pollutant named clofibric acid can be really improved by photocatalysis through a parametric comprehensive investigation and optimization study based on response surface methodology. Its novelty comes from the approach used to enhance the efficiency of the photocatalytic degradation of clofibric acid. A custom central composite design consisting of 49 trials was applied for process modeling and a quadratic robust model was derived based on the analysis of variance for the optimization of the process parameters. The effective removal of the target molecule with about 70% carbon mineralization was achieved under optimal photocatalytic conditions: 1.5 mg/L as the initial concentration of pollutant, 0.61 g/L catalyst, and an irradiation time of 190 min. Further, it was provided that nitrates play a positive role in the removal of this pollutant, while hydrogenocarbonates slow down its elimination. The ecotoxicity evaluation at different trophic levels confirmed the low toxicity of photodegradation by-products. Data analysis demonstrated that response surface methodology is a reliable approach for the optimization of the interactive effects of photocatalytic process parameters and is able to enhance their performance for the complete elimination of this hardly removed water pollutant.

Integrated approach of photo-assisted electrochemical oxidation and sequential biodegradation of textile effluent

Synthetic azo dyes are extensively used in the textile industries, which are being released as textile effluent into the environment presence of azo dyes in the environment is great environmental concern therefore treatment of textile effluent is crucial for proper release of the effluent into the environment. Electrochemical oxidation (EO) is extensively used in the degradation of pollutants because of its high efficiency. In this study, photo-assisted electrooxidation (PEO) followed by biodegradation of the textile effluent was evaluated. The pretreatment of textile effluent was conducted by EO and PEO in a tubular flow cell with TiO₂-Ti/IrO₂-RuO₂ anode and titanium cathode under different current densities (10, 15, and 20 mA cm^-2). The chemical oxygen demand level reduced from 3150 mg L^-1 to 1300 and 600 mg L^-1under EO and PEO, respectively. Furthermore, biodegradation of EO and PEO pretreated textile effluent shows reduction in chemical oxygen demand (COD) from 1300 mg L^-1 to 900 mg L^-1and 600 mg L^-1to 110 mg L^-1, respectively. The most abundant genera were identified as Acetobacter, Achromobacter, Acidaminococcus, Actinomyces, and Acetomicrobium from the textile effluent. This study suggests that an integrated approach of PEO and subsequent biodegradation might be an effective and eco-friendly method for the degradation of textile effluent.

Photocatalytic activity of CuO nanoparticles for organic and inorganic pollutants removal in wastewater remediation

Heterogeneous photocatalysis is a promising technology for eradicating organic, inorganic, and microbial pollutants in water and wastewater remediation. It is a more preferable method to other conventional wastewater treatment approaches on account of its low cost, environmental benignity, ability to proceed at ambient temperature and pressure conditions, and capability to completely degrade pollutants under appropriate conditions into environmentally safe products. In heterogeneous photocatalysis, pollutant removal is mainly induced by in-situ generated reactive radicals and their subsequent attack when energetic radiation impinges on the semiconductor catalyst. As such, for the effective and economical removal of wastewater pollutants, the employed catalyst should have high photonic efficiency, less toxic, abundant, chemically and photochemically stableand visible light active. Copper (II) oxide (CuO) is one among such promising compounds and its photocatalytic performance has been hampered primarily by rapid recombination and slow mobility of photogenerated charge carriers. So, this review provides an overview of the strategies adopted to mitigate the aforementioned drawbacks and also other operational parameters to boost its catalytic activity towards the elimination of toxic organic and inorganic metal ion contaminants in an aqueous media.

Heterogeneous Photodegradation for the Abatement of Recalcitrant COD in Synthetic Tanning Wastewater

Tannery wastewater is considered one of the most contaminated and problematic wastes since it consists of considerable amounts of organic and inorganic compounds. These contaminants result in high chemical oxygen demand (COD), biochemical oxygen demand (BOD), and total suspended solids (TSS). In this work, the heterogeneous photodegradation of recalcitrant COD in wastewater from the tanning industry was investigated, in particular the recalcitrant COD due to the presence of vegetable tannins extracted from mimosa and chestnut and from synthetic tannins based on 4,4′ dihydroxy phenyl sulfone. TiO2 Aeroxide P-25 was employed to study the photodegradation of model molecules in batch conditions under different parameters, namely initial concentration of COD, temperature, and catalyst dose. The maximum COD abatement reached was 60%. Additionally, preliminary kinetic investigation was conducted to derive the main kinetic parameters that can be useful for process scale-up. It was found to be independent of the temperature value but linearly dependent on both catalyst loading and the initial COD value.

Clay-Supported Metal Oxide Nanoparticles in Catalytic Advanced Oxidation Processes: A Review

Advanced oxidation processes (AOPs) utilizing heterogeneous catalysts have attracted great attention in the last decade. The use of solid catalysts, including metal and metal oxide nanoparticle support materials, exhibited better performance compared with the use of homogeneous catalysts, which is mainly related to their stability in hostile environments and recyclability and reusability. Various solid supports have been reported to enhance the performance of metal and metal oxide catalysts for AOPs; undoubtedly, the utilization of clay as a support is the priority under consideration and has received intensive interest. This review provides up-to-date progress on the synthesis, features, and future perspectives of clay-supported metal and metal oxide for AOPs. The methods and characteristics of metal and metal oxide incorporated into the clay structure are strongly influenced by various factors in the synthesis, including the kind of clay mineral. In addition, the benefits of nanomaterials from a green chemistry perspective are key aspects for their further considerations in various applications. Special emphasis is given to the basic schemes for clay modifications and role of clay supports for the enhanced mechanism of AOPs. The scaling-up issue is suggested for being studied to further applications at industrial scale.

Photocatalysis: an effective tool for photodegradation of dyes-a review

The disposal of dye-contaminated wastewater is a major concern around the world for which a variety of techniques are used for its treatment. The photocatalytic treatment of dye-contaminated wastewater is one of the treatment methods. Semiconductor-assisted photocatalytic treatment of dye-contaminated wastewater has gained pronounced attention recently. This review outlines the recent advancements in the photocatalytic treatment of dye-contaminated wastewater. The photocatalytic degradation of dyes follows three types of mechanisms: (1) dye sensitization through charge injection, (2) indirect dye degradation through oxidation/reduction, and (3) direct photolysis of dye. Several experimental parameters like initial concentration of dyes, pH, and catalyst dosage significantly affect the photocatalytic degradation of dyes. The photocatalytic materials can be categorized into three generations. The single-component (e.g., ZnO, TiO₂) and multiple component semiconductor metal oxides (e.g., ZnO-TiO₂, Bi₂O₃-ZnO) are categorized as first-generation and second-generation photocatalysts, respectively. The photocatalysts dispersed on an inert solid substrate (e.g., Ag-Al₂O₃, ZnO-C) are classified as third-generation photocatalysts. Finally, we reviewed the challenges that affect the photocatalytic degradation of dyes.

Photocatalytic degradation of acetaminophen in water via ultraviolet light and titanium dioxide thin films part II: chemical and kinetic aspects

Among the large family of emergent pharmaceutical contaminants, we find acetaminophen (ACE) that critically needs to be removed from wastewater. Advanced Oxidation Process (AOP) have proven effective in the degradation of large molecular contaminants from water. To the best of our knowledge this is the first study reported on the degradation of ACE based on immobilized TiO2 thin films. In an effort to increase the understanding of the efficiency of the degradation process, an in-depth investigation of the effects of the structure, i.e., coating layers and the amount of surface, i.e., number of coated slides used, is needed. Transparent, anatase-form TiO2 thin films were prepared via the sol-gel method (Rawal, S., S. Buer, J. R. Sanders, and P. E. Arce. 2021. “Photocatalytic Degradation of Acetaminophen from Water Solutions Via Thin Films. Part I: Synthesis and Characterization of TiO2 Thin Films.” International Journal of Reactor Engineering [Accepted]) and deposited onto glass microscope slides using a novel spraying technique, with coatings ranging from one to 10 layers. This contribution summarizes the effect of several key factors including initial concentration of the ACE, the number of coating layers (6, 8, and 10) on the glass slides and the number (4 and 6) of slides on the degradation levels for three selected media, e.g., acid, neutral and base. Comparisons studies, supported by statistical analysis between two different sets (4 and 6) of slides with discussion of potential physical-chemical reasons behind the behaviors are reported. Finally, global, first order kinetic rate constants are also reported for the different conditions used in the investigation. Although further research would be needed, in general the results are promising for the potential degradation of ACE in continuous flow systems by using immobilized TiO2 on surfaces as thin films.

Photocatalytic degradation of acetaminophen from water solutions via thin films part I: preparation, characteriation, and analysis of titanium dioxide thin films

The utilization of titanium dioxide (TiO2) photocatalysis for water and air purification is a frequently used method due to TiO2 having properties making it chemically inert, highly cost-effective, abundant, non-toxic, and environmentally-friendly. In an effort to increase the efficiency of the degradation process, an in-depth understanding of the effects of the structure and number of thin film coatings is needed. Transparent, anatase-form titanium dioxide thin films were prepared via the sol-gel method and deposited onto microscopic glass slides using a novel spraying technique, with coatings ranging from 1 to 10. Characterization of the TiO2 thin film coated slides was performed using X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. The contribution shows that the coating technique is efficient in covering important areas of the surface and that it is suitable for a multiple coating layers thin film. The SEM imagines show that the surface of the slides increase coverage as the number of layers increases. This is potentially suitable for a mechanized spraying approach to upscaling the production of thin films for advanced oxidation applications.

Electrospun Poly(methyl methacrylate)/TiO2 Composites for Photocatalytic Water Treatment

Electrospinning was successfully used for the one-step fabrication of poly(methyl methacrylate) (PMMA) fibers loaded with an inorganic photocatalyst—titanium oxide (TiO₂). By tuning the PMMA/TiO₂ ratio and the electrospinning conditions (applied voltage, needle tip-to-collector distance, and flow rates), PMMA/TiO₂ composites with selected organic/inorganic ratios, tailored designs, and targeted properties were obtained. The morphology of the electrospun composites was affected by the amount of TiO₂ incorporated into the PMMA fibers. In addition, the inorganic photocatalyst had an impact on the wettability, thermal stability, and optical properties of the electrospun composites. In particular, the surface wettability of the composites was strongly influenced by UV light irradiation and from hydrophobic became superhydrophilic. Moreover, PMMA/TiO₂ composites had enhanced tensile strength in comparison with those of bare PMMA mats. The electrospun PMMA/TiO₂ composites showed excellent photocatalytic efficiency against the model organic pollutant—methylene blue—which is very promising for the future development of membranes that are highly efficacious for photocatalytic water treatment.

Silver nanomaterials: synthesis and (electro/photo) catalytic applications

In view of their unique characteristics and properties, silver nanomaterials (Ag NMs) have been used not only in the field of nanomedicine but also for diverse advanced catalytic technologies. In this comprehensive review, light is shed on general synthetic approaches encompassing chemical reduction, sonochemical, microwave, and thermal treatment among the preparative methods for the syntheses of Ag-based NMs and their catalytic applications. Additionally, some of the latest innovative approaches such as continuous flow integrated with MW and other benign approaches have been emphasized that ultimately pave the way for sustainability. Moreover, the potential applications of emerging Ag NMs, including sub nanomaterials and single atoms, in the field of liquid-phase catalysis, photocatalysis, and electrocatalysis as well as a positive role of Ag NMs in catalytic reactions are meticulously summarized. The scientific interest in the synthesis and applications of Ag NMs lies in the integrated benefits of their catalytic activity, selectivity, stability, and recovery. Therefore, the rise and journey of Ag NM-based catalysts will inspire a new generation of chemists to tailor and design robust catalysts that can effectively tackle major environmental challenges and help to replace noble metals in advanced catalytic applications. This overview concludes by providing future perspectives on the research into Ag NMs in the arena of electrocatalysis and photocatalysis.

Photoelectrochemical Application and Charge Transport Dynamics of a Water-Stable Organic-Inorganic Halide (C6H4NH2CuCl2I) Film in Aqueous Solution

A water-stable thin film composed of C₆H₄NH₂CuCl₂I was fabricated using spin-coating precursor solutions that dissolved equimolar amounts of C₆H₄NH₂I and CuCl₂ in N,N-dimethylformamide. Photoelectrochemical characteristics show that the C₆H₄NH₂CuCl₂I film demonstrated a stable photocurrent (∼1 μA/cm²) in an aqueous solution under white light (11.5 mW/cm²) even after 3000 s, while exhibiting a photon-to-current efficiency of 0.093% under AM1.5 (100 mW/cm²) illumination. However, these values were significantly lower than those of the CH₃NH₃PbX₃ (X = I, Cl) film in solid devices. The electron diffusion length L(e^-) (373 nm) and hole diffusion length L(h⁺) (177 nm) in the C₆H₄NH₂CuCl₂I photoelectrode were significantly lower than those of CH₃NH₃PbX₃, limiting the photoelectrochemical and photocatalysis performances. Moreover, L(h⁺) was shorter than L(e^-) in the C₆H₄NH₂CuCl₂I photoelectrode, resulting in the hole-collecting efficiency [η_c(h⁺)] being lower than the electron-collecting efficiency [η_c(e^-)]. A CuO interlayer was introduced as a hole transport layer for the C₆H₄NH₂CuCl₂I photoelectrode, which improved L(h⁺) and η_c(h⁺).

Photocatalytic Removal of Pharmaceuticals from Greywater

High concentrations of pharmaceuticals have been detected in greywater effluents treated using up-to-date technologies. Finding a suitable additional treatment before this effluent is reused is urgently needed to ensure the reused water meets quality standards. This paper reports the use of heterogeneous photocatalysis on anatase and rutile nanopowders to remove naproxen, metformin and sulfamethoxazole, at practically relevant concentrations found in membrane bioreactor (MBR)-treated greywater. A low anatase concentration of 400 mg L−1 was sufficient to efficiently degrade the pharmaceuticals listed above, with complete degradation observed in 5 h. The effect of background species presented in greywater was, to some extent, comparable to that of the OH-radical scavenger. These results prove that photocatalysis using anatase TiO2 is a feasible additional treatment for greywater recycling.

Highly stable halide perovskite with Na incorporation for efficient photocatalytic degradation of organic dyes in water solution

To overcome water instability and low photocatalytic activity of lead-free halide perovskite for the degradation of organic dyes, we report a novel photocatalyst of lead-free halide perovskite with Na incorporation and employ it for the photocatalytic degradation of organic dyes in water solution under visible light irradiation. The main purpose of this work is to confirm the feasibility of lead-free halide perovskite with Na incorporation for improving the photocatalytic efficiency and recyclability in water solution and further to explore the mechanism behind the enhancement of photocatalytic performance after Na incorporation. The results show that Cs₂Ag_0.60Na_0.40InCl₆ can increase the dye degradation rate by at least 50% than the lead-free halide perovskite (Cs₂AgInCl₆) and the photocatalyst of Ag substituted by Na (Cs₂NaInCl₆). The degradation efficiency of rhodamine 6G catalyzed by Cs₂Ag_0.60Na_0.40InCl₆ reaches 94.94% over 60 min, which is 72% higher than that catalyzed by Cs₂NaInCl₆ and 27% higher than that catalyzed by Cs₂AgInCl₆. What's more, the degradation efficiency of methyl orange catalyzed by Cs₂Ag_0.60Na_0.40InCl₆ is 90.39% within 150 min, which is 66% higher than that catalyzed by Cs₂NaInCl₆ and 54% higher than that catalyzed by Cs₂AgInCl₆. Moreover, the photocatalyst of Cs₂Ag_0.60Na_0.40InCl₆ exhibits a desirable recyclability by water exposure, retaining the degradation efficiency over 90% after five cycles. The strengthened photocatalytic performance in the presence of Cs₂Ag_0.60Na_0.40InCl₆ is ascribed to an increase of radiative recombination rate and an improvement of average lifetime to 204 ns since an appropriate Na incorporation at the atomic ratio of Na/Ag=4:6 breaks the original crystal lattice and meanwhile increases the electron and hole overlap. The work proves a great potential of halide perovskite with Na incorporation for the highly efficient photocatalytic degradation of organic dyes in water solution.

Hairy silica nanosphere supported metal nanoparticles for reductive degradation of dye pollutants

Hairy materials can act as a sort of scaffold for the fabrication of functional hybrid composites. In this work, silica nanospheres modified with covalently grafted poly(4-vinylpyridine) (P4VP) brushes, namely, "hairy" silica spheres, were utilized as a support for the anchorage of metal nanoparticles (MNPs), thus resulting in the hierarchical SiO₂@P4VP/MNP structure. In this triple-phase boundary heteronanostructure, the SiO₂-supported MNPs are well stabilized by the P4VP matrix to avoid aggregation and leaching. These SiO₂@P4VP/MNP nanocomposites exhibit good catalytic activity in the reductive degradation of organic dyes, i.e., 4-nitrophenol and rhodamine B and possess excellent stability and recyclability for five successive cycles.

Bibliometric analysis of advanced oxidation processes (AOPs) in wastewater treatment: global and Ibero-American research trends

Advanced oxidation processes (AOPs) constitute a developing area of particular interest for researchers in different fields due to their broad range of applications. However, there are few studies dedicated to the bibliometric analysis of AOPs. Hence, a systematic literature review of research publications (research articles, review articles, and book chapters) from 1980 to 2018 was carried out to visualize and evaluate research trends on AOPs around the world and, especially in Ibero-America (IA), on the field of wastewater treatment. Using the most extensive databases in literature search, Scopus and Web of Science (WoS), which encompass 95% of the publications in the world, a total of 18,751 records were retrieved by limiting the search results to words associated with AOPs in the titles, keyword, and abstracts. Raw data were manually organized and filtered, standardizing authors and institution names, publication titles, and keywords for the purpose of eliminating double-counted entries. Similarly, homonymous authors and institutions were identified for all records retrieved. The bibliometric dataset was processed using the VantagePoint software. The research trends visualized about AOPs were as follows: number of publications per triennium, publications by country, participation by continent, most important journals and authors, most referenced institutions, global network of co-authors, and keywords network visualization, highlighting the Ibero-American contribution to global research.

Synthesis and Characterization of ZnO-TiO2/Carbon Fiber Composite with Enhanced Photocatalytic Properties

Herein, we prepared a novel photocatalytic ZnO-TiO2 loaded carbon nanofibers composites (ZnO-TiO2-CNFs) via electrospinning technique followed by a hydrothermal process. At first, the electrospun TiO2 NP-embedded carbon nanofibers (TiO2-CNFs) were achieved using electrospinning and a carbonization process. Next, the ZnO particles were grown into the TiO2-CNFs via hydrothermal treatment. The morphology, structure, and chemical compositions were studied using state-of-the-art techniques. The photocatalytic performance of the ZnO-TiO2-CNFs composite was studied using degrading methylene blue (MB) under UV-light irradiation for three successive cycles. It was noticed that the ZnO-TiO2-CNFs nanocomposite showed better MB removal properties than that of other formulations, which might be due to the synergistic effects of carbon nanofibers and utilized metal oxides (ZnO and TiO2). The adsorption characteristic of carbon fibers and matched band potentials of ZnO and TiO2 combinedly help to boost the overall photocatalytic performance of the ZnO-TiO2-CNFs composite. The obtained results from this study indicated that it can be an economical and environmentally friendly photocatalyst.

Shapes Control of Bi2WO6 Nano-Structures as Photo-Fenton Catalysts for Pulping Wastewater Treatment

Bi2WO6 assembled by flower-like microspheres and nanosheets were controllably synthesized through a one-step hydrothermal approach. Multiple technologies, including X-ray powder diffraction (XRD), scanning electron microscopy (SEM), and UV–Vis diffuse reflectance spectrum (UV–Vis), were carried out to characterize the as-synthesized samples. The photocatalytic efficiency of Bi2WO6 synthesized with a series of temperature and pH values shows different morphologies and photocatalytic properties. The photocatalyst (Bi2WO6) synthesized at 220 °C and pH of 7 exhibited the best photocatalytic performance, with the methylene blue (MB) degradation approaching 91.6% after reaction time of 60 min. Free radical capture experiments indicate that •OH is the primary reactive species in the methylene blue (MB) degradation reaction, h+ and •O2− contribute negligible influence, while the addition of H2O2 significantly improves the photocatalytic activity of Bi2WO6. Biodegraded poplar preconditioning refiner chemical alkaline peroxide mechanical pulp wastewater (PPW) was treated over Bi2WO6 under UV light (Bi2WO6/UV/H2O2); chemical oxygen demand (CODCr) and color degradation rate were 85.8% and 92.0%, respectively. These results show that Bi2WO6 semiconductors can be introduced as an efficient and stable photocatalyst for industry wastewater treatment.

An ultrasound-assisted photocatalytic treatment to remove an herbicidal pollutant from wastewaters

Pollutants of emerging concern contaminate surface and ground water. Advanced oxidation processes treat these molecules and degrade them into smaller compounds or mineralization products. However, little information on coupled advanced oxidation techniques and on the degradation pathways of these pollutants is available to identify possible ecotoxic subproducts. In the present work, we investigate the ultrasound assisted photocatalytic degradation pathway of the herbicide Isoproturon. We worked in batch mode in a thermostatic glass reactor. We compared the activity of nanometric TiO₂ P25 with that of Kronos 1077, a micrometric TiO₂. We discuss the individual, additive and synergistic degradation action of photolysis, sonolysis, sonophotolysis, and sonophotocatalysis by varying catalyst loading and/or ultrasound power for the last three techniques. With 0.1 g L^-1 catalyst, photocatalysis and sonophotopcatalysis completely degrade Isoproturon within 240 min and 60 min, respectively (>99% conversion). Sonophotocatalysis breaks Isoproturon down into smaller molecules than photocatalysis alone.

Tailoring the stability/aggregation of one-dimensional TiO2(B)/titanate nanowires using surfactants

The increased utilization of one-dimensional (1D) TiO2 and titanate nanowires (TNWs) in various applications was the motivation behind studying their stability in this work, given that stability greatly influences both the success of the application and the environmental impact. Due to their high abundance in aqueous environments and their rich technological applicability, surfactants are among the most interesting compounds used for tailoring the stability. The aim of this paper is to determine the influence of surfactant molecular structure on TNW stability/aggregation behavior in water and aqueous NaBr solution by dynamic and electrophoretic light scattering. To accomplish this, two structurally different quaternary ammonium surfactants (monomeric DTAB and the corresponding dimeric 12-2-12) at monomer and micellar concentrations were used to investigate TNW stability in water and NaBr. It was shown that TNWs are relatively stable in Milli-Q water. However, the addition of NaBr induces aggregation, especially as the TNW mass concentration increases. DTAB and 12-2-12 adsorb on TNW surfaces as a result of the superposition of favorable electrostatic and hydrophobic interactions. As expected, the interaction of TNWs with 12-2-12 was stronger than with DTAB, due to the presence of two positively charged head groups and two hydrophobic tails. As a consequence of the higher adsorption of 12-2-12, TNWs remained stable in both media, while DTAB showed an opposite behavior. In order to gain more insight into changes in the surface properties after surfactant adsorption on the TNW surface, a surface complexation model was employed. With this first attempt to quantify the contribution of the surfactant structure on the adsorption equilibrium according to the observed differences in the intrinsic log K values, it was shown that 12-2-12 interacts more strongly with TNWs than DTAB. The modelling results enable a better understanding of the interaction between TNWs and surfactants as well as the prediction of the conditions that can promote stabilization or aggregation.

Eco-friendly nanostructured Zn–Al layered double hydroxide photocatalysts with enhanced photocatalytic activity

Zn–Al layered double hydroxides (Zn–Al LDHs) with various reaction times were synthesized by a hydrothermal method at constant pH, and they were tested for the removal of RhB with or without post-calcination treatment.

Heterogeneous photocatalysis and its potential applications in water and wastewater treatment: a review

There has been a considerable amount of research in the development of sustainable water treatment techniques capable of improving the quality of water. Unavailability of drinkable water is a crucial issue especially in regions where conventional drinking water treatment systems fail to eradicate aquatic pathogens, toxic metal ions and industrial waste. The research and development in this area have given rise to a new class of processes called advanced oxidation processes, particularly in the form of heterogeneous photocatalysis, which converts photon energy into chemical energy. Advances in nanotechnology have improved the ability to develop and specifically tailor the properties of photocatalytic materials used in this area. This paper discusses many of those photocatalytic nanomaterials, both metal-based and metal-free, which have been studied for water and waste water purification and treatment in recent years. It also discusses the design and performance of the recently studied photocatalytic reactors, along with the recent advancements in the visible-light photocatalysis. Additionally, the effects of the fundamental parameters such as temperature, pH, catalyst-loading and reaction time have also been reviewed. Moreover, different techniques that can increase the photocatalytic efficiency as well as recyclability have been systematically presented, followed by a discussion on the photocatalytic treatment of actual wastewater samples and the future challenges associated with it.

Toward new benchmark adsorbents: preparation and characterization of activated carbon from argan nut shell for bisphenol A removal

The use of argan nut shell as a precursor for producing activated carbon was investigated in this work. Two activated carbons AC-HP and AC-Na were prepared from argan nut shell by chemical activation method using phosphoric acid (H₃PO₄) and sodium hydroxide (NaOH), respectively. Textural, morphological, and surface chemistry characteristics were studied by nitrogen physisorption, TGA, SEM, TXRF, FTIR, XRD, and by determining the pH_PZC of the AC-HP. The adsorption experiments revealed that AC-HP was more efficient in adsorption of BPA due to high specific surface area (1372 m²/g) compared to AC-Na (798 m²/g). The obtained adsorption data of BPA on AC-HP correlated well with the pseudo-second-order model and the Langmuir isotherm (Qmax = 1250 mg/g at 293 K). The thermodynamic parameters (ΔG° < 0, ΔH° < 0, and ΔS° < 0) indicate that adsorption of BPA on AC-HP was spontaneous and exothermic in nature. The regeneration of AC-HP showed excellent results after 5 cycles (95-93%). This work does not only provide a potential way to use argan nut shell but also represents a sustainable approach to synthesize AC-HP, which might be an ideal material for various applications (energy storage, catalysis, and environmental remediation).

Evaluation of the photocatalytic ability of a sol-gel-derived MgO-ZrO2 oxide material

This paper deals with the synthesis and characterization of a novel group of potential photocatalysts, based on sol-gel-derived MgO-ZrO2 oxide material. The material was synthesized in a typical sol-gel system using organic precursors of magnesia and zirconia, ammonia as a promoter of hydrolysis and methanol as a solvent. All materials were thoroughly analyzed, including morphology and particle sizes, chemical composition, identification of characteristic functional groups, porous structure parameters and crystalline structure. The proposed methodology of synthesis resulted in obtaining pure MgO-ZrO2 oxide material with micrometric-sized particles and a relatively high surface area. The samples underwent an additional calcination process which led to the crystalline phase of zirconia being formed. The key element of the study was the evaluation of the effectiveness of decomposition of C.I. Basic Blue 9 dye. It was shown that the calcined materials exhibit both satisfactory adsorption and photocatalytic activity with respect to the decomposition of a selected model organic impurity. Total dye removal varied in the range of 50-70%, and was strongly dependent on process parameters such as quantity of photocatalyst, time of irradiation, and the addition of promoters.

Non-catalytic and catalytic degradation of effluent dissolved organic matter under UVA-and UVC-irradiation tracked by advanced spectroscopic tools

Non-catalytic and catalytic photodegradation of effluent dissolved organic matter (EfDOM) was examined under two different light sources (UVA and UVC). The degradation behavior was tracked by dissolved organic carbon (DOC), UV absorbance, and different fluorescent components. Catalytic UV irradiation resulted in much higher degradation rates than those without photocatalysts (TiO₂ and ZnO) regardless of the tracking variables. For non-catalytic degradation, the highest removal rates of UV absorbance were found at wavelengths close to the irradiation of either UVC or UVA, while the photocatalytic degradation rates were consistently higher at longer wavelengths. The pseudo first-order rates of UV absorbance individually calculated at several representative wavelengths were very consistent with the sequential orders interpreted from two-dimensional correlation spectroscopy (2D-COS). Excitation emission matrix - parallel factor analysis (EEM-PARAFAC) identified one tryptophan-like (C1) and two humic-like (C2 and C3) components from EfDOM samples. Among those, C1 exhibited the lowest adsorption extent and the highest degradation rates for both photocatalysts, suggesting that the photocatalysis is mainly governed by hydroxyl radicals in aqueous solution. All observed degradation behaviors were well explained by the irradiation wavelengths, the extent of adsorption onto catalysts, and the presumed structure of the tracked component. Our study demonstrated that EEM-PARAFAC and 2D-COS could provide further insights into both non-catalytic and catalytic degradation of EfDOM upon UV-irradiation.

Oxidative removal of phenol by HRP-immobilized beads and its environmental toxicology assessment

Horseradish peroxidase shows potential biological and environmental applications on the removal of phenolic compounds. In the present study, the HRP-immobilized beads were synthesized to detect the efficiency of the removal of phenol at optimum pH and H2O2 concentration. Comparative in vitro cytotoxicity of phenol/treated solutions were evaluated in HeLa, HepG2 and mcf-7 cells by using MTT method along with flow cytometry study for cell viability and cell cycle distributions. The results showed that the toxicity of phenol solutions were greatly reduced after treated by HRP-immobilized beads, and phenol could lead to deactivate of cells in the S phase and preventing them from going into the G2/M checkpoint. In addition, molecular docking study showed that phenol was a valid inhibitor for the cyclin E in the cell cycle and cell metabolism. Thereby, we established a suitable strategy with promising application for efficient harmless removal of phenol, which significantly decreased the cytotoxic impacts of phenol.