Effectiveness of bulking agents for co-composting penicillin mycelial dreg (PMD) and sewage sludge in pilot-scale system

Biochar derivation at low temperature: A novel strategy for harmful resource usage of antibiotic mycelial dreg

Antibiotic mycelial dreg (AMD) has been categorized as hazardous waste due to the high residual hazardous contaminants. Inappropriate management and disposal of AMD can cause potential environmental and ecological risks. In this study, the potential of pleuromutilin mycelial dreg (PMD) as a novel feedstock for preparing tetracycline hydrochloride (TC) adsorbent was explored to achieve safe management of PMD. The results suggested that residual hazardous contaminants were completely eliminated after pyrolysis. With the increase of pyrolysis temperature, the yields, H/C, O/C, (O + N)/C, and pore size in PMD-derived biochars (PMD-BCs) decreased, while BET surface area and pore volume increased, resulting in the higher stability of the PMD-BCs prepared from higher temperatures. The TC adsorption of the PMD-BCs increased from 27.3 to 46.9 mg/g with the increase of the pyrolysis temperature. Surprisingly, pH value had a strong impact on the TC adsorption, the adsorption capacity of BC-450 increased from 6.5 to 71.1 mg/g when the solution pH value increased from 2 to 10. Lewis acid-base interaction, pore filling, π-π interaction, hydrophobic interaction, and charge-assisted hydrogen bond (CAHB) are considered to drive the adsorption. This work provides a novel pathway for the concurrent detoxification and reutilization of AMD.

Mechanisms for more efficient antibiotics and antibiotic resistance genes removal during industrialized treatment of over 200 tons of tylosin and spectinomycin mycelial dregs by integrated meta-omics

To mitigate the environmental risks posed by the accumulation of antibiotic mycelial dregs (AMDs), this study first attempted over 200 tons of mass production fermentation (MP) using tylosin and spectinomycin mycelial dregs alongside pilot-scale fermentation (PS) for comparison, utilizing the integrated-omics and qPCR approaches. Co-fermentation results showed that both antibiotics were effectively removed in all treatments, with an average removal rate of 92%. Antibiotic resistance gene (ARG)-related metabolic pathways showed that rapid degradation of antibiotics was associated with enzymes that inactivate macrolides and aminoglycosides (e.g., K06979, K07027, K05593). Interestingly, MP fermentations with optimized conditions had more efficient ARGs removal because homogenization permitted faster microbial succession, with more stable removal of antibiotic resistant bacteria and mobile genetic elements. Moreover, Bacillus reached 75% and secreted antioxidant enzymes that might inhibit horizontal gene transfer of ARGs. The findings confirmed the advantages of MP fermentation and provided a scientific basis for other AMDs.

Antibiotics and antibiotic resistance gene dynamics in the composting of antibiotic fermentation waste - A review

Fate of antibiotics and antibiotic resistance genes (ARGs) during composting of antibiotic fermentation waste (AFW) is a major concern. This review article focuses on recent literature published on this subject. The key findings are that antibiotics can be removed effectively during AFW composting, with higher temperatures, appropriate bulking agents, and suitable pretreatments improving their degradation. ARGs dynamics during composting are related to bacteria and mobile genetic elements (MGEs). Higher temperatures, suitable bulking agents and an appropriate C/N ratio (30:1) lead to more efficient removal of ARGs/MGEs by shaping the bacterial composition. Keeping materials dry (moisture less than 30%) and maintaining pH stable around 7.5 after composting could inhibit the rebound of ARGs. Overall, safer utilization of AFW can be realized by optimizing composting conditions. However, further removal of antibiotics and ARGs at low levels, degradation mechanism of antibiotics, and spread mechanism of ARGs during AFW composting require further investigation.

Composting and vermicomposting of sewage sludge at various C/N ratios: Technological feasibility and end-product quality

Even though sewage sludge (SS) contains a high level of pollutants, it is rich in essential plant nutrients and has the potential to enhance soil fertility. However, the SS must be further treated through pre-composting plus vermicomposting to make it safe for use on food crops. More research and data are needed to determine how different carbon-to-nitrogen ratios (C/N) affect the feasibility and quality of composting vs vermicomposting of SS. Therefore, in this study we comprehensively evaluated the feasibility and end-product quality of compost and vermicompost produced from SS under different C/N ratios. SS was mixed with pelletized wheat straw (PWS) at various proportions to produce C/N ratios of 6:1, 18:1, 28:1, and 38:1, then pre-composted for 14 days followed by vermicomposting using the earthworm Eisenia andrei for 120 days. Agrochemical properties were measured at 0, 30, 60, 90, and 120 days. Results revealed significantly higher levels of agrochemicals in vermicompost compared to compost, including total potassium (37-88%) and magnesium (4.3-12%), nitrate nitrogen (71-98%), available potassium (53-88%), available phosphorus (79%), available magnesium (54-453%), available boron (48-303%), and available copper (2.5-82%). However, lower levels of ammonium nitrogen by (59-85%), available iron (2.3-51.3%), available manganese (29.7-52.2%), available zinc (10.5-29.8%), total carbon (0.75-4.5%), and total nitrogen (1.6-22.2%) were measured. Comparison of the various C/N ratios, showed that vermicompost with an 18:1 C/N ratio outperformed compost and demonstrated the highest earthworm population (165 pieces/kg). Thus, vermicomposting SS at an 18:1 C/N ratio is strongly recommended as a sustainable technology for producing high-quality vermicompost from SS.

Performance and mechanism of Pb2+ and Cd2+ ions’ adsorption via modified antibiotic residue-based hydrochar

This study investigated the hydrochar-based porous carbon prepared by combining the technical route of hydrothermal carbonization (HTC) + chemical activation. The hydrochar morphology was adjusted by changing the activation reaction conditions and adding metal salts. Experiments showed that the activation of KHCO₃ significantly increased the specific surface area and pore size of the hydrochar. Besides, oxygen-rich groups on the surface of the activated hydrochar interacted with heavy metal ions to achieve efficient adsorption. The activated hydrothermal carbon adsorption capacity for Pb²⁺ and Cd²⁺ ions reached 289 and 186 mg/g, respectively. The adsorption mechanism study indicated that the adsorption of Pb²⁺ and Cd²⁺ was related to electrostatic attraction, ion exchange, and complexation reactions. The "HTC + chemical activation" technology was environmentally friendly and effectively implemented antibiotic residues. Carbon materials with high adsorption capacity can be prepared so that biomass resources can be utilized with excessive value, as a consequence presenting technical assistance for the comprehensive disposal of organic waste in the pharmaceutical industry and establishing a green and clean production system.

Evolution of antibiotic resistance genes and bacterial community during erythromycin fermentation residue composting

The removal efficiency of antibiotic resistance genes (ARGs) is the biggest challenge for the treatment of erythromycin fermentation residue (EFR). In the current research, 0% (control), 10% (T1), and 30% (T2) spray-dried EFR were composted with bulking materials, consisting of cattle manure and maize straw, for 30 days. Environmental factors and bacterial community on the behaviors of ARGs were further investigated. Apart from the high levels of erythromycin, the electrical conductivities were also increased by 66.7% and 291.7% in the samples of T1 and T2, respectively. After 30 days of composting, total ARGs in the samples of control were decreased by 78.1%-91.2%, but those of T1 and T2 were increased 14.5-16.7- and 38.5-68.7-fold. ARGs related to ribosomal protection (erm) dominated the samples of T1 and T2 at D 13 and 30, especially that ermF accounted for more than 80% of the total ARGs. Furthermore, the results of bacterial community revealed that EFR promoted the growth of Proteobacteria and Bacteroidetes, but inhibited that of Actinobacteria, Verrucomicrobia and Chloroflexi. Network analysis revealed that the enriched ARGs had strong correlation with seven bacterial genera, including Halomonas, Oceanobacillus, and Alcaligenes, most of which are halotolerant. Above all, erythromycin combined with high salinity can have synergistic effect on the enrichment of ARGs and their hosts.

Effects of pH and Metal Ions on the Hydrothermal Treatment of Penicillin: Kinetic, Pathway, and Antibacterial Activity

Antibiotic residues lead to the risk of resistance gene enrichment, which is the main reason why penicillin mycelial dreg (PMD) is defined as hazardous waste. Hydrothermal treatment (HT) is an effective method to treat penicillin mycelial dreg, but the degradation mechanism of penicillin is unclear. In the study, we researched the effects of pH (4-10) at 80-100 °C and metal ions (Mn²⁺, Fe²⁺, Cu²⁺, and Zn²⁺) at several concentrations on the HT of penicillin, identified the degradation products (DPs) under different conditions, and evaluated the antibacterial activity of hydrothermally treated samples. The results show that penicillin degradation kinetics highly consistent with pseudo-first-order model (R² = 0.9447-0.9999). The degradation rates (k) at pH = 4, 7, and 10 were 0.1603, 0.0039, and 0.0485 min^-1, indicating acidic conditions were more conducive to penicillin degradation. Among the four tested metal ions, Zn²⁺ had the most significant catalytic effect. Adding 5 mg·L^-1 Zn²⁺ caused 100% degradation rate at pH = 7 after HT for 60 min. Six degradation products (DPs) with low mass-to-charge (m/z ≤ 335) were detected under acidic condition. However, only two and three DPs were observed in the samples catalyzed by Zn²⁺ and alkali, respectively, and penilloic acid (m/z = 309) was the main DPs under these conditions. Furthermore, no antibacterial activity to Bacillus pumilus was detected in the medium with up to 50% addition of the treated samples under acidic condition. Even though acid, alkali, and some metal ions can improve the degradation ability of penicillin, it was found that the most effective way for removing its anti-bacterial activity was under the acidic condition. Therefore, resistance residue indicates the amount of additive in the process of resource utilization, and avoids the enrichment of resistance genes.

Safety of composts consisting of hydrothermally treated penicillin fermentation residue: Degradation products, antibiotic resistance genes and bacterial diversity

Combining hydrothermal treatment and composting is an effective method to dispose of penicillin fermentation residue (PFR), but the safety and related mechanism are still unclear. In this study, penicillin solution was hydrothermally treated to decipher its degradation mechanism, and then hydrothermally treated PFR (HT-PFR) was mixed with bulking agents at ratios of 2:0 (CK), 2:1.5 (T1), and 2:5 (T2) to determine the absolute abundance of antibiotic resistance genes (ARGs) and the succession of bacterial community. Results showed that penicillin was degraded to several new compounds without the initial lactam structure after hydrothermal treatment. During composting, temperature and pH of the composts increased with the raising of HT-PFR proportion, except the pH at days 2. After 52 days of composting, the absolute copies of ARGs (blaTEM, blaCMY2, and blaSFO) and the relative abundance of bacteria related to pathogens were reduced significantly (P < 0.05). Especially, the total amount of ARGs in the samples of CK and T1 were decreased to equal level (around 5 log₁₀ copies/g), which indicated that more ARGs were degraded in the latter by the composting process. In the CK samples, Bacteroidetes and Proteobacteria accounted for ~69.8% of the total bacteria, but they were gradually replaced by Firmicutes with increasing proportions of HT-PFR, which can be caused by the high protein content in PFR. Consisting with bacterial community, more gram-positive bacteria were observed in T1 and T2, and most of them are related to manganese oxidation and chitinolysis. As composting proceeded, bacteria having symbiotic or pathogenic relationships with animals and plants were reduced, but those related to ureolysis and cellulolysis were enriched. Above all, hydrothermal treatment is effective in destroying the lactam structure of penicillin, which makes that most ARGs and pathogenic bacteria are eliminated in the subsequent composting.

Polycistronic Expression System for Pichia pastoris Composed of Chitino- and Chitosanolytic Enzymes

Chitin is one of the most abundant biopolymers. Due to its recalcitrant nature and insolubility in accessible solvents, it is often considered waste and not a bioresource. The products of chitin modification such as chitosan and chitooligosaccharides are highly sought, but their preparation is a challenging process, typically performed with thermochemical methods that lack specificities and generate hazardous waste. Enzymatic treatment is a promising alternative to these methods, but the preparation of multiple biocatalysts is costly. In this manuscript, we biochemically characterised chitin deacetylases of Mucor circinelloides IBT-83 and utilised one of them for the construction of the first eukaryotic, polycistronic expression system employing self-processing 2A sequences. The three chitin-processing enzymes; chitin deacetylase of M. circinelloides IBT-83, chitinase from Thermomyces lanuginosus, and chitosanase from Aspergillus fumigatus were expressed under the control of the same promoter in methylotrophic yeast Pichia pastoris and characterised for their synergistic action towards their respective substrates.

Pyrolysis of antibiotic mycelial dreg and characterization of obtained gas, liquid and biochar

The disposal and utilization of antibiotic mycelial dreg (AMD), which has been identified as a hazardous waste in China, are a serious concern because of the residual antibiotic and huge annual output. Pyrolysis is a promising technology to treat AMD. However, the pyrolysis of AMD is not studied in an adequate degree, particularly no attention has been paid to the release and distribution of the phosphorus in AMD during pyrolysis. Therefore, the present work studied the pyrolysis of AMD more comprehensively. The influence of pyrolysis temperature on product yields and characteristics, together with the release and distribution of nitrogen and phosphorus, and the antibiotic residue in products, were investigated. The results suggested that residual antibiotic was eliminated after pyrolysis. Nitrogen was mainly contained in the biochar and liquid products, while phosphorus was mainly retained in the biochar. Liquid products were characterized by abundant oxygen and nitrogen-containing compounds, while biochar was featured of both abundant nitrogen and inorganic phosphate groups. Pyrolysis temperature showed a significant effect on product yields and characteristics, and a low pyrolysis temperature is recommended considering the recycling of nitrogen and phosphorus. The disposal of AMD through pyrolysis conforms to the principles of AMD disposal.

Composting of oxytetracycline fermentation residue in combination with hydrothermal pretreatment for reducing antibiotic resistance genes enrichment

Hydrothermal pretreatment can efficiently remove the residual antibiotics in oxytetracycline fermentation residue (OFR), but its effect on antibiotic resistance genes (ARGs) during composting remains unclear. This study compared the shifts in bacterial community and evolutions in ARGs and integrons during different composting processes of OFRs with and without hydrothermal pretreatment. The results demonstrated that hydrothermal pretreatment increased the bacterial alpha diversity at the initial phase, and increased the relative abundances of Proteobacteria and Actinobacteria but decreased that of Bacteroidetes at the final phase by inactivating mycelia and removing residual oxytetracycline. Composting process inevitably elevated the abundance and relative abundance of ARGs. However, the increase in ARGs was significantly reduced by hydrothermal pretreatment, because the removal of oxytetracycline decreased their potential host bacteria and inhibited their horizontal gene transfer. The results demonstrated that hydrothermal pretreatment is an efficient strategy to reduce the enrichment of ARGs during the OFR composting.

Nitrogen release of hydrothermal treatment of antibiotic fermentation residue and preparation of struvite from hydrolysate

Hydrothermal treatment (HT) is an appropriate treatment method for organic hazardous wastes such as antibiotic fermentation residue (AR). However, there is no effective way to recycle hydrolysate with high nitrogen content. In this study, penicillin fermentation residue (PR, a type of AR) was used as raw material to study the release and redistribution of N during hydrothermal process. And the influences of pH, ion ratio and reaction time on the preparation of struvite were analyzed. The results showed that the nitrogen in PR consists of Inorganic-N and Amino-N. Most of N (~70%) that entered hydrolysate was converted into org-N, NH₄⁺-N and NO₃^--N. At 260 °C, the NH₄⁺-N concentration was 2842.78 mg/L, accounting for 45.2% of total nitrogen. The remaining amino-N in the hydrochar was gradually converted to pyridine-N, pyrrole-N and quaternary-N with the increasing of temperature. At pH = 9.5, Mg²⁺: NH₄⁺: PO₄^3- = 1.3: 1: 1.15, struvite was prepared by hydrolysate. And over 95% removal rate of NH₄⁺-N could be achieved. XRD analysis showed that the main component of the product was struvite, which was further confirmed by SEM-EDX and FT-IR. It was found that there was trace amount of MgKPO₄·H₂O precipitation in the product. In addition, Mg₃(PO₄)₂ precipitation might also be formed at pH = 10.

Effects of moisture and carbon/nitrogen ratio on gaseous emissions and maturity during direct composting of cornstalks used for filtration of anaerobically digested manure centrate

This study investigated the maturity and gaseous emission during direct composting of cornstalks used as organic media for filtration of anaerobically digested manure centrate. Effects of moisture and carbon/nitrogen (C/N) ratio on composting performance were evaluated. Results show that cornstalks could effectively retain suspended solids and organic matter in digested manure centrate to lower their C/N ratio and attain microbial inoculation. Filtered cornstalks became more compostable when their moisture decreased from 76% to 60% or C/N ratio increased from 12 to 24. Nevertheless, such adjustment aggravated the emission of greenhouse and odours gases during composting. Regardless of composting conditions, the phylum Firmicutes was the most dominant with reduced abundance during composting. Similar reduction also occurred to several abundant phyla, including Atribacteria, Synergistetes and Euryarchaeota. By contrast, the phylum Bacteroidetes, Chloroflexi, Proteobacteria and Actinobacteria enriched as composting progressed. In addition, compost maturity was insignificantly affected by matrix moisture and C/N ratio.

Effects of macroporous adsorption resin on antibiotic resistance genes and the bacterial community during composting

Swine manure is considered a reservoir for antibiotic resistance genes (ARGs), which may enter the soil and then the food chain to endanger human health. This study investigated the effects of adding 0%, 5%, and 15% (w/w) macroporous adsorption resin (MAR) on ARGs and the bacterial community during composting. The results showed that the addition of MAR reduced the abundances of ARGs (14.14-99.44%) and mobile genetic elements (MGEs) (47.83-99.48%) after swine manure composting. Significant positive correlations were detected between ARGs and MGEs, and thus the variations in MGEs may have led to the changes in ARGs. Redundancy analysis showed that MGEs had stronger effects on ARGs than environmental factors and the bacterial community. Network analysis suggested that ARGs and MGEs co-existed in common host bacteria. In conclusion, the results showed that adding 5% MAR can reduce the risk of ARG transmission.

Using of indigenous bulking agents (IBAs) in complementary stabilization and enhancing of dewatered sludge class B to class a on a full scale

BACKGROUND

Different bulking agents are used in the compost of dewatered sludge (DWS). The aim of this study has been using of indigenous bulking agents (IBAs) in the enhancing of the DWS class of municipal wastewater from class B to class A and complementary stabilization of it for production of green manure in Sari city, Iran.

METHODS

Three IBAs including the Saccharum Wastes (SW), Citrus Purning Wastes (CPW) and Phragmites Australis (PA) from eight IBAs were selected to be compared with the sawdust (SD) that was as a control bulking agent. Five turned windrow piles were constructed on a full scale and on base of optimal C/N equal 25.All experiments were performed on the base of the standard methods on initial mix and final compost.

RESULTS

Among five windrow piles, P5 was been the best pile with a weighting ratio of DWS to IBAs (DWS: SW: CPW: PA) equal 1: 0.2: 0.24: 0.28. Pile P1 with weighting ratio DWS: SW equal 1: 0.6, Pile P3 with weighting ratio DWS: PA equal 1: 0.84, Pile P2 with weighting ratio DWS: CPW equal 1: 0.73 and Pile P4 with weighting ratio DWS: SD equal 1: 0.57 were placed in the next rounds. The results showed that the class of DWS enhanced to Class A for about 80 to 97 days and complementary stabilization of DWS by IBAs was done well and produced green manure in term of organic matter, potassium, germination index, PH, C/N and electrical conductivity had reached to the Grade 1 of Iran's manure 10716 standard and in term of phosphorus and moisture had reached to the Grade 2 of this standard. Also heavy metals were below the maximum permissible of standards.

CONCLUSION

Using of IBAs, had a higher efficiency than the control bulking agent (sawdust) in enhancing sludge class and its stabilization, so that using of them in combination (mix of IBAs) had the highest efficiency and respectively, Saccharum Wastes (SW), Phragmites Australis (PA), Citrus pruning wastes (CPW) were placed in the next round, and sawdust was placed after them. By adding suitable IBAS, with an optimal ratio in turned windrow method, the class of DWS of sari WWTP enhanced to Class A and complementary stabilization of DWS has been well done and the produced green manure has been reached to agricultural standards and can be safely used in agriculture.

Effects of co-composting of lincomycin mycelia dregs with furfural slag on lincomycin degradation, degradation products, antibiotic resistance genes and bacterial community

This study explored the effects of co-composting of lincomycin mycelia dregs (LMDs) with furfural slag on variations in antibiotic resistance genes (ARGs) and the bacterial community. The results showed that more than 99% lincomycin was reduced after composting. Moreover, the total absolute and relative abundance of ARGs increased by 180 and 5 times, respectively. The gene lnuA was detected in the LMDs compost and it was proved to participate in lincomycin biodegradation based on the analysis of Pearson's correlation and the lincomycin degradation byproducts. Redundancy analysis showed the succession of the bacterial community had a greater influence than the environmental parameters (residual lincomycin, C/N, pH and temperature) on the variation of ARGs during composting. Composting was not effective in reducing most of the ARGs and intI1 and thus the LMDs compost is dangerous to the ecological environment.

Performance evaluation of gaseous emissions and Zn speciation during Zn-rich antibiotic manufacturing wastes and pig manure composting

In this study, the co-composting performance of Zn-rich antibiotic manufacturing wastes (AMW) and pig manure (PM) was evaluated. Four treatments, representing 2.5%, 5%, 10% and 20% of AMW (of PM dry weight) and control without AMW, were established during composting. Results suggested that the temperature, pH, electrical conductivity, NH₄⁺-N and germination index in end product met the maturity and sanitation requirement. More than 99% of residual antibiotic was removed. Compared with PM composting alone, the cumulative CH₄ and N₂O emissions in AMW composting increased by 13.46-79.00% and 10.78-65.12%, respectively. While the higher mixing ratios of AMW (10% and 20%) presented a negative impact on composing by inhibiting organic matter (OM) degradation and higher NH₃ emissions. The AMW had highly bioavailable Zn, but the exchangeable faction of Zn significantly decreased with the composting progress.

Effects of co-composting of lincomycin mycelia dregs with furfural slag on lincomycin degradation, maturity and microbial communities

This paper investigated the effect of co-composting of lincomycin mycelia dregs (LMDs) with furfural slag on the degradation of lincomycin, maturity and microbial communities. Results showed that after 66 days composting, the concentration of lincomycin was removed above 99%. The final pH, C/N and germination index (GI) all met the national standards in maturity. Enumeration of total cultivable microbes showed the composting process was not inhibited by the addition of LMDs. Microbial diversity suggested that co-composting was beneficial to increase the abundance and diversity of bacterial communities for LMDs' treatment. Canonical correlation analysis (CCA) indicated the bacteria communities were strongly affected by residual lincomycin, with lincomycin reduced greatly, microbial communities of T and CK became similar at the end of composting. The potential bacteria to degrade lincomycin were Anaerococcus, Peptostreptococcus, and Lactobacillus. Based on these results, this research indicated that the co-composting was a feasible treatment for LMDs.

Performance of co-composting sewage sludge and organic fraction of municipal solid waste at different proportions

In this study, the co-composting performance of sewage sludge (SS) and organic fraction of municipal solid waste (OFMSW) at different proportions was investigated. Cornstalk was added at 15% (of total wet weight) to improve the co-composting process. Results show that higher SS proportion could rapidly initialize the co-composting process; while increasing OFMSW percentage enhanced organic content for biodegradation, thus prolonging the thermophilic period and increasing the humification degree during co-composting. However, excessive OFMSW required longer co-composting period to ensure a desirable compost maturity and quality. Over 15days of rapid co-composting, adding 55-85% OFMSW aggravated compost quality by increasing the compost salinity (3.5-4.6mScm^-1) and plant toxicity (indicated by the low germination index of 54.1-77.3%). Moreover, different proportions of SS and OFMSW varied gaseous emissions during co-composting. Our results suggested that OFMSW should be less than 55% for rapid co-composting with SS and cornstalk.

Assessing the stability in dry mycelial fertilizer of Penicillium chrysogenum as soil amendment via fluorescence excitation-emission matrix spectra: organic matter's transformation and maturity

Utilization as dry mycelial fertilizer (DMF) produced from penicillin fermentation fungi mycelium (PFFM) with an acid-heating pretreatment is a potential way. To study the transformation and stability of water-extractable organic matter in DMF-amended soil via fluorescence regional integration (FRI) of fluorescence excitation-emission matrix (EEM), a soil experiment in pot was carried out. The results showed that residual penicillin (about 32 mg/kg) was almost degraded in the first 5 days, indicating that the drug pollution was in control. The pH value, DOC, DON, and DOC/DON presented a classical profile, but germination index (GI) leveled off about 0.13 till day 13 in DMF-12% treatment due to the severe phytotoxicity. The addition of DMF significantly increased the soil microbial populations in contrast to the CON treatment. The EEM showed that the protein-like and microbial byproduct-like matters vanished on the 25th and 33rd days, whereas the fulvic-like substances appeared on the 7th day. The humic-like substances existed in original samples but their content greatly enhanced finally. The FRI results showed that P _{V, n}/P _{III, n} reached the highest value of 1.84 on the 25th day, suggesting that DMF maintained stable in amended soil. Because of its consistency with the results of GI and DOC/DON, the EEM-FRI has a potential to evaluate the stability of DMF in soil.

Behavior of antibiotic resistance genes during co-composting of swine manure with Chinese medicinal herbal residues

Swine manure is considered to be a reservoir for antibiotic resistance genes (ARGs) but little is known about the variations in ARGs during the co-composting of swine manure with Chinese medicinal herbal residues (CMHRs). Thus, this study explored the effects of CMHRs on the variations in ARGs during co-composting with swine manure. The results showed that CMHRs could reduce effectively most of the targeted ARGs (0.18-2.82logs) and mobile genetic elements (MGEs) (0.47-3.34logs). The correlations indicated that CMHRs might decrease the spread of ARGs via horizontal gene transfer. Redundancy analysis showed that the bacterial communities had more important effects on the variations in ARGs compared with environmental factors and MGEs. The results of this study demonstrate that CMHRs can decrease the abundances of ARGs and MGEs, as well as reducing the risk of ARGs spreading during the application of compost products to farmland.

Performance of microwave treatment for disintegration of cephalosporin mycelial dreg (CMD) and degradation of residual cephalosporin antibiotics

Significant amounts of cephalosporin mycelial dreg (CMD) are still being generated from biopharmaceutical processes, representing both an economic and environmental burden for pharmaceutical factories. This study investigates the microwave (MW) treatment of CMD at a relatively mild temperature (100°C) within 15min. The results reveal that the MW treatment disintegrates the CMD efficiently and that the residual cephalosporin C (CPC) is almost degraded after sufficient irradiation. MW heating temperature strongly influences the polymer's release. SCOD (soluble chemical oxygen demand), soluble proteins and carbohydrates have significant positive correlations to the temperature (r=0.993, 0.983 and 0.992, respectively; p<0.01). 3D-EEM fluorescence spectra indicate that the key organic matters relate to temperature as well as microwave energies. Furthermore, more than 99.9% of the residual antibiotics in CMD are degraded by MW irradiation without antibacterial activities that are proven by the possible degradation pathway we elucidate. These results suggest that microwave irradiation treatment not only disintegrates CMD and destroys mycelial cells but also degrades the residual cephalosporin antibiotics, which implies the possibility for practical applications.

Can fungi compete with marine sources for chitosan production?

Chitosan, a β-1,4-linked glucosamine polymer is formed by deacetylation of chitin. It has a wide range of applications from agriculture to human health care products. Chitosan is commercially produced from shellfish, shrimp waste, crab and lobster processing using strong alkalis at high temperatures for long time periods. The production of chitin and chitosan from fungal sources has gained increased attention in recent years due to potential advantages in terms of homogenous polymer length, high degree of deacetylation and solubility over the current marine source. Zygomycetous fungi such as Absidia coerulea, Benjaminiella poitrasii, Cunninghamella elegans, Gongrenella butleri, Mucor rouxii, Mucor racemosus and Rhizopus oryzae have been studied extensively. Isolation of chitosan are reported from few edible basidiomycetous fungi like Agaricus bisporus, Lentinula edodes and Pleurotus sajor-caju. Other organisms from mycotech industries explored for chitosan production are Aspergillus niger, Penicillium chrysogenum, Saccharomyces cerevisiae and other wine yeasts. Number of aspects such as value addition to the existing applications of fungi, utilization of waste from agriculture sector, and issues and challenges for the production of fungal chitosan to compete with existing sources, metabolic engineering and novel applications have been discussed to adjudge the potential of fungal sources for commercial chitosan production.

Feasibility study of recycling cephalosporin C fermentation dregs using co-composting process with activated sludge as co-substrate

Composting is a potential alternative for cephalosporin C fermentation dregs (CCFDs) compared with incineration process or landfill because of its advantage of recovering nutrients. In this research, CCFDs and activated sludge (AS) were co-composted to analyze the feasibility of recycling the nutrients in CCFDs. A pilot-scale aerobic composting system with an auto-control system was used in this research, and the maturity and security of the compost product were evaluated. The temperature of the composting mixtures was maintained above 55°C for more than 3 days during the composting, indicating that co-composting of CCFDs and AS could reach the compost maturity standard, and the seeds germination index (GI) increased from 17.61% to 68.93% by the end of the composting process (28 days). However, the degradation rate of cephalosporin C (CPC) was only 6.58% during the composting process. Monitoring the quality of antibiotic resistance genes (ARGs) in the composts showed that the log copy of blaTEM in the composts increased from 2.15 in the initial phase to 6.37 after 28 days. Long-term investigation of CPC degradation and ARGs variation was conducted for the composts; CPC could still be detected after the maturity phases. A removal efficiency of 49.10% could be achieved in 110 days, while the log copy of ARGs increased to 7.93. Although a higher GI value (>80.00%) was observed, the risk of recycling the CCFDs compost product into land is still high.