Sensitive electrochemical sensor using a graphene-polyaniline nanocomposite for simultaneous detection of Zn(II), Cd(II), and Pb(II)

Enhancing early warning: A DNA biosensor with polyaniline/graphene nanocomposite for label-free voltammetric detection of saxitoxin-producing harmful algae

Yearly reports of detrimental effects resulting from harmful algal blooms (HAB) are still received in Malaysia and other countries, particularly concerning fish mortality and seafood contamination, both of which bear consequences for the fisheries industry. The underlying reason is the absence of a dependable early warning system. Hence, this research aims to develop a single DNA biosensor that can detect a group of HAB species known for producing saxitoxin (SXT), which is commonly found in Malaysian waters. The screen-printed carbon electrode (SPCE)-based DNA biosensor was fabricated by covalent grafting of the 3' aminated DNA probe of the sxtA4 conserved domain in SXT-producing dinoflagellates on the reverse-phase polymerized polyaniline/graphene (PGN) nanocomposite electrode via carbodiimide linkage. The introduction of a carboxyphenyl layer to the PGN nanotransducing element was essential to augment the carboxylic groups on the graphene (RGO), facilitating attachment with the aminated DNA. The synergistic effect of the asynthesized nanocomposite of PANI and RGO, tremendously enhanced the electron transfer rate of the ferri/ferrocyanide redox probe at the SPCE transducer surface, allowing for the label-free bioanalytical assay of complementary DNA targets. The developed DNA biosensor featuring the capacity to detect a broad range of Alexandrium minutum (A. minutum) cell concentrations, ranging from 10 to 10,000,000 cells L-1. The quantification of A. minutum cells from pure algal culture by the electrochemical DNA biosensor has been well-validated with traditional microscopic techniques. Furthermore, Alexandrium tamiyavanichii, another toxigenic HAB species, exhibited a similar electrochemical characteristic signal to those observed with A. minutum, whilst the biosensor yielded appreciably distinctive results when subjected to a non-toxigenic microalgae species as a negative control, i.e. Isochrysis galbana. A compendium DNA biosensor design and electrochemical detection strategy at laboratory scale serves as a precursor to the potential development of portable device for on-site detection, thus expanding the utility and scope of biosensor technology.

A review of biocompatible polymer-functionalized two-dimensional materials: Emerging contenders for biosensors and bioelectronics applications

Bioelectronics, a field pivotal in monitoring and stimulating biological processes, demands innovative nanomaterials as detection platforms. Two-dimensional (2D) materials, with their thin structures and exceptional physicochemical properties, have emerged as critical substances in this research. However, these materials face challenges in biomedical applications due to issues related to their biological compatibility, adaptability, functionality, and nano-bio surface characteristics. This review examines surface modifications using covalent and non-covalent-based polymer-functionalization strategies to overcome these limitations by enhancing the biological compatibility, adaptability, and functionality of 2D nanomaterials. These surface modifications aim to create stable and long-lasting therapeutic effects, significantly paving the way for the practical application of polymer-functionalized 2D materials in biosensors and bioelectronics. The review paper critically summarizes the surface functionalization of 2D nanomaterials with biocompatible polymers, including g-C3N4, graphene family, MXene, BP, MOF, and TMDCs, highlighting their current state, physicochemical structures, synthesis methods, material characteristics, and applications in biosensors and bioelectronics. The paper concludes with a discussion of prospects, challenges, and numerous opportunities in the evolving field of bioelectronics.

Pyridine appended pyrimidine bis hydrazone: Zn2+/ATP detection, bioimaging and functional properties of its dinuclear Zn(II) complex

A pyridine functionalized pyrimidine-based system, H2P was successfully synthesized, characterized, and evaluated for its remarkable selective characteristics towards Zn2+ and ATP ions. The chemical sensing capabilities of H2P were demonstrated through absorption, fluorescence, and NMR spectroscopic techniques. The probe exhibited outstanding sensitivity when interacting with the ions, demonstrating relatively strong association constants and impressively low detection limits. The comprehensive binding mechanism of H2P with respect to Zn2+ and ATP ions was investigated using a combination of analytical methods, including Job's plot, NMR spectroscopy, mass spectrometry, and density functional theory (DFT) experiments. The interesting sensing ability of H2P for Zn2+/ATP ions was harnessed for live cell bioimaging and other diverse on-site detection purposes, including paper strips, cotton swabs, and applications involving mung bean sprouts. Further, the fluorescent probe demonstrated its effectiveness in detecting Zn2+ and ATP within live cells, indicating its significant potential in the realm of biological imaging applications. Moreover, the molecular configuration of the zinc complex (H2P-Zn2Cl4), derived from H2P, was elucidated using X-ray crystallography. This complex exhibited intriguing multifunctional attributes, encompassing its capability for detecting picric acid and for reversible acid/base sensing responses. The enhanced conducting behavior of the complex as well as its resistance properties were investigated by performing I-V characteristics and electrochemical impedance spectroscopic (EIS) experiments respectively.

Electrochemical Sensing of Cadmium and Lead Ions in Water by MOF-5/PANI Composites

For the first time, composites of metal-organic framework MOF-5 and conjugated polymer polyaniline (PANI), (MOF-5/PANI), prepared using PANI in its conducting (emeraldine salt, ES) or nonconducting form (emeraldine base, EB) at various MOF-5 and PANI mass ratios, were evaluated as electrode materials for the electrochemical detection of cadmium (Cd2+) and lead (Pb2+) ions in aqueous solutions. Testing of individual components of composites, PANI-ES, PANI-EB, and MOF-5, was also performed for comparison. Materials are characterized by Raman spectroscopy, scanning electron microscopy (SEM) and dynamic light scattering (DLS), and their electrochemical behavior was discussed in terms of their zeta potential, structural, morphology, and textural properties. All examined composites showed high electrocatalytic activity for the oxidation of Cd and Pb to Cd2+ and Pb2+, respectively. The MOF/EB-1 composite (71.0 wt.% MOF-5) gave the highest oxidation currents during both individual and simultaneous detection of two heavy metal ions. Current densities recorded with MOF/EB-1 were also higher than those of its individual components, reflecting the synergistic effect where MOF-5 offers high surface area for two heavy metals adsorption and PANI offers a network for electron transfer during metals' subsequent oxidation. Limits of detection using MOF/EB-1 electrode for Cd2+ and Pb2+ sensing were found to be as low as 0.077 ppm and 0.033 ppm, respectively. Moreover, the well-defined and intense peaks of Cd oxidation to Cd2+ and somewhat lower peaks of Pb oxidation to Pb2+ were observed at voltammograms obtained for the Danube River as a real sample with no pretreatment, which implies that herein tested MOF-5/PANI electrodes could be used as electrochemical sensors for the detection of heavy metal ions in the real water samples.

Advances in the Use of Conducting Polymers for Healthcare Monitoring

Conducting polymers (CPs) are an innovative class of materials recognized for their high flexibility and biocompatibility, making them an ideal choice for health monitoring applications that require flexibility. They are active in their design. Advances in fabrication technology allow the incorporation of CPs at various levels, by combining diverse CPs monomers with metal particles, 2D materials, carbon nanomaterials, and copolymers through the process of polymerization and mixing. This method produces materials with unique physicochemical properties and is highly customizable. In particular, the development of CPs with expanded surface area and high conductivity has significantly improved the performance of the sensors, providing high sensitivity and flexibility and expanding the range of available options. However, due to the morphological diversity of new materials and thus the variety of characteristics that can be synthesized by combining CPs and other types of functionalities, choosing the right combination for a sensor application is difficult but becomes important. This review focuses on classifying the role of CP and highlights recent advances in sensor design, especially in the field of healthcare monitoring. It also synthesizes the sensing mechanisms and evaluates the performance of CPs on electrochemical surfaces and in the sensor design. Furthermore, the applications that can be revolutionized by CPs will be discussed in detail.

Emerging Trends in nanostructured materials-coated screen printed electrodes for the electrochemical detection of hazardous heavy metals in environmental matrices

Heavy metal ions (HMIs) have become a significant contaminant in recent years. The increase in heavy metal pollution is a serious situation, requiring progressively robust, fast sensing, highly sensitive, and suitable techniques for heavy metal detection. Compared to other classical analytical methods, electroanalytical techniques, especially stripping voltammetric techniques with modified screen-printed electrodes (SPEs), have several advantages, such as fast sensing, great sensitivity, specificity, and long-time stability. Therefore, these techniques are more suitable for HMI detection. In this review, the nanostructured materials used to coat SPEs for the electrochemical determination of HMI are summarized. Additionally, the electrode fabrication method, modification steps, and electroanalytical study of these materials are systematically discussed. Hence, this review will support the researchers in precisely evaluating the electrochemical HMIs detection through highly sensitive stripping voltammetric techniques using SPE modified with nanostructured carbon and their allotropes, metal, metal oxides and their nanocomposites as sensor materials. Moreover, modified electrodes real time detection of HMIs in different food and environmental samples were briefly discussed.

Solid-state ion-selective electrodes for the first potentiometric determination of the anti-COVID 19 drug Remdesivir in human plasma; A comparative study

Establishing sensitive and targeted analytical methodologies for drug identification in biological fluids as well as screening of treatments that can counteract the most severe COVID-19 infection-related side effects are of utmost importance. Here, first attempts have been made for determination of the anti-COVID drug Remdesivir (RDS) in human plasma using four potentiometric sensors. Calixarene-8 (CX8) was used as an ionophore applied to the first electrode (Sensor I). The second had a layer of dispersed graphene nanocomposite coating (Sensor II). (Sensor III) was fabricated using nanoparticles of polyaniline (PANI) as ion-to–electron transducer. A reverse-phase polymerization using polyvinylpyrrolidone (PVP) was employed to create a graphene-polyaniline (G/PANI) nanocomposite electrode (Sensor IV). Surface morphology was confirmed by Scanning Electron Microscope (SEM). UV absorption spectra and Fourier Transform Ion Spectrophotometry (FTIR) also supported their structural characterization. The impact of graphene and polyaniline integration on the functionality and durability of the manufactured sensors was examined using the water layer test and signal drift. In the ranges of concentration of 10⁻⁷ to 10⁻² mol/L and 10⁻⁷ to 10⁻³, sensors II & IV exhibited linear responses; respectively while sensors I & III displayed linearity within 10⁻⁶ to 10⁻² mol/L. The target drug was easily detectable using LOD down to 100 nmol/L. The developed sensors satisfactorily offered sensitive, stable, selective and accurate estimate of Remdesivir (RDS) in its pharmaceutical formulation as well as spiked human plasma with recoveries ranging from 91.02 to 95.76 % with average standard deviations less than 1.85. The suggested procedure was approved in accordance with ICH recommendations.

Electrochemical determination of zinc(II) using N1-hydroxy-N1,N2-diphenylbenzamidine and multi-walled carbon nanotubes modified carbon paste electrode

In this study, a new carbon paste electrode modified with a laboratory-synthesized ligand, N¹-hydroxy-N¹,N²-diphenylbenzamidine (HDPBA) and multi-walled carbon nanotubes (MWCNTs) (HDPBA‒MWCNTs/CPE) has been developed. The modified electrode was applied for preconcentration and voltammetric determination of zinc ions (Zn(II)) by square wave anodic stripping voltammetry (SWASV). The preconcentration of Zn(II) on the electrode surface was performed in 0.1 M Brinton Robinson (B-R) buffer solution (pH 6) at an applied potential of -1.30 V versus Ag/AgCl for 120 s, followed by stripping in the positive potential scan of the SWASV after a quit time of 10 s. Under optimized experimental conditions, the proposed electrode exhibited a wider linear dynamic response for Zn(II) in a concentration range of 0.02-10.00 μM with a detection limit of 2.48 nM. This is due to the excellent metal-chelation property of the ligand, and the good conductivity and large surface area of MWCNTs which significantly improved the sensing performance of the nanocomposite modified electrode. The selectivity of the electrode was studied by evaluating the interference effects of various foreign ions on the peak current of Zn(II). The method exhibited high reproducibility with a relative standard deviation (RSD) of 3.1%. The present method was applied for the determination of zinc ions in water samples. The recovery values in the tested samples were found to be 98.50-106.0%, indicating a good accuracy of the proposed electrode. Furthermore, the electrochemical behavior of HDPBA in acetonitrile and aqueous solutions has been studied.

Conductive Polymer Nanoparticles as Solid Contact in Ion-Selective Electrodes Sensitive to Potassium Ions

A preparation method of nanocomposites based on poly (3-octylthiophene-2,5-diyl) (POT) and carbon black (CB) as the transducer of an all-solid potassium ion selective electrode is proposed. POT is used as the dispersant of CB, and the obtained nanocomposites have unique characteristics, including high conductivity, high capacitance and high stability. The potassium ion selective electrode based on POT and CB was characterized by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and chronopotentiometry. The results showed that the detection limit of potassium ions was 10−6.2 M, and the slope was 57.6 ± 0.8 mV/façade. The water layer test and anti-interference test show that the electrode has high hydrophobicity, the static contact angle reaches 139.7° and is not easily affected by light, O2 and CO2.

Simultaneous voltammetric sensing of Zn2+, Cd2+, and Pb2+ using an electrodeposited Bi-Sb nanocomposite modified carbon paste electrode

A sensor for detecting Zn²⁺, Cd²⁺, and Pb²⁺ ions simultaneously based on the square wave anodic stripping response at a bismuth antimony (Bi-Sb) nanocomposite electrode was developed. The electrode was prepared in situ by electrodepositing bismuth and antimony on the surface of a carbon-paste electrode (CPE) while also reducing the analyte metal ions. The structure and performance of the Bi-Sb/CPE electrode were studied using scanning electron microscopy, X-ray diffraction, electrochemical impedance spectroscopy, and cyclic voltammetry. Operational conditions including the concentration of Sb and Bi, the type of electrolyte, pH, and preconcentration conditions were optimized. The linear ranges were determined to be 5-200 μg L^-1 for Zn²⁺, 1-200 μg L^-1 for Cd²⁺, and 1-150 μg L^-1 for Pb²⁺ with the optimized parameters. The limits of detection were 1.46 μg L^-1, 0.27 μg L^-1, and 0.29 μg L^-1 for Zn²⁺, Cd²⁺, and Pb²⁺, respectively. Furthermore, the Bi-Sb/CPE sensor is capable of selective determination of the target metals in the presence of the common cationic and anionic interfering species (Na⁺, K⁺, Ca²⁺, Mg²⁺, Fe³⁺, Mn²⁺, Co²⁺, Cl^-, SO₄ ^2- and HCO₃ ^-). Finally, the sensor was successfully applied to the simultaneous determination of Zn²⁺, Cd²⁺, and Pb²⁺ in a variety of real-world water samples.

Fabrication and development of a microfluidic paper-based immunosorbent assay platform (μPISA) for colorimetric detection of hepatitis C

Paper-based microfluidics is an emerging analysis tool used in various applications, especially in point-of-care (PoC) diagnostic applications, due to its advantages over other types of microfluidic devices in terms of simplicity in both production and operation, cost-effectiveness, rapid response time, low sample consumption, biocompatibility, and ease of disposal. Recently, various techniques have been developed and utilized for the fabrication of paper-based microfluidics, such as photolithography, micro-embossing, wax and PDMS printing, etc. In this study, we offer a fabrication methodology for a microfluidic paper-based immunosorbent assay (μPISA) platform and the detection of Hepatitis C Virus (HCV) was carried out to validate this platform. A laser ablation technique was utilized to form hydrophobic barriers easily and rapidly, which was the major advantage of the developed fabrication methodology. The characterization of the μPISA platform was performed in terms of micro-channel properties using bright-field (BF) microscopy, and surface properties using scanning electron microscopy (SEM). At the same time, sample volume and liquid handling capacity were analyzed quantitatively. Ablation speed (S) and laser power (P) were optimized, and it was shown that one combination (10P60S) provided minimal deviation in micro-channel dimensions and prevented deterioration of hydrophobic barriers. Also, the minimum hydrophobic barrier width, which prevents cross-barrier bleeding, was determined to be 255.92 ± 10.01 μm. Furthermore, colorimetric HCV NS3 detection was implemented to optimize and validate the μPISA platform. Here, HCV NS3 in both PBS and human blood plasma was successfully detected by the naked eye at concentrations as low as 1 ng mL^-1 and 10 ng mL^-1, respectively. Moreover, the limit of detection (LoD) values for HCV NS3 were acquired as 0.796 ng mL^-1 in PBS and 2.203 ng mL^-1 in human blood plasma with a turnaround time of 90 min. In comparison with conventional ELISA, highly sensitive and rapid HCV NS3 detection was accomplished colorimetrically on the developed μPISA platform.

A sensitive and rapid determination of zinc ion (Zn2+) using electrochemical sensor based on f-MWCNTs/CS/PB/AuE in drinking water

An electrochemical method for detecting the presence of zinc (Zn²⁺) ions in drinking water was developed using functionalized multi-walled carbon nanotubes (f-MWCNTs) and chitosan (CS). Numerous cylinder-shaped graphene molecules make up f-MWCNTs, which have a high mechanical and electrical conductivity. CS benefits from nanomaterials include biocompatibility, biodegradability, and low toxicity, which are excellent in capacity absorption of metal ions. Dangerous levels of metal ions such as zinc are currently present in drinking water as a result of human and natural activity. Zinc toxicity is associated with a variety of disorders, including Alzheimer's, Parkinson's, diabetes, and cancer. This study incorporated f-MWCNTs and CS with Prussian blue (PB) immobilised on a gold electrode (AuE). Several parameters, including as buffers, pH, scan rate, redox indicator, accumulation time, and volume, were optimised using the cyclic voltammetry (CV) method. According to the CV method, the optimal parameters were phosphate buffered saline (0.1 M, pH 2), 5 mM Prussian blue, 200 mVs^-1 scan rate, and 5 s accumulation time. Under ideal circumstances, the differential pulse voltammetry (DPV) method was used to determine the Zn²⁺ ions concentration range of 0.2-7.0 ppm. The limit of detection (LOD) was 2.60 × 10^-7 mol L^-1 with a correlation coefficient of R² = 0.9777. The recovery rate of the developed sensor (f-MWCNTs/CS/PB/AuE) ranged from 95.78 to 98.96%. The developed sensor showed a variety of advantages for detecting Zn²⁺ in drinking water, including a quick setup process, quick detection, high sensitivity, and mobility. This study developed the essential sensor for monitoring Zn²⁺ levels in drinking water in the future.

Fully integrated colorimetric sensor based on transparency substrate for salbutamol determination

•

Facile colorimetric method for the determination of salbutamol based on a simple redox reaction using permanganate as reagent was first investigated at the transparency-based analytical device (TAD).

•

The colorimetric TAD sensor was in-lab constructed using a transparent PET-based substrate, showing good compatibility with the permanganate reagent which could result in a vivid color change, clearly observed by the naked eye.

•

This proposed colorimetric TAD sensor was successfully applied for salbutamol determination in real drug samples with good accuracy and satisfactory recovery, highlighting the potential capability of this TAD-based colorimetric sensor in pharmaceutical application.

A facile colorimetric method based on a typical redox reaction was first developed for the determination of salbutamol (SAL) using a low-cost and portable transparency-based analytical device (TAD). The TAD was simply fabricated by wax-printing onto a transparent polymer-based substrate to create the hydrophobic barriers and the colorimetric reaction zones where the color changes could be easily observed with the naked eye. Potassium permanganate (KMnO₄), a common oxidizing agent, was deliberately used as a colorimetric reagent for SAL. Once SAL reacted with KMnO₄ in the acidified system, it could undergo oxidation and the color of KMnO₄ subsequently changed from light pink to orange. The color change corresponding to the SAL concentration could be clearly observed at the TAD sensor. In addition, the reaction color could be recorded using a digital camera and then analyzed by ImageJ for quantitative analysis. Under the optimized conditions, the developed method together with the TAD sensor exhibited high efficiency for SAL determination with linearity ranging from 0.5 to 40 mg·L⁻¹ and a limit of detection (LOD) of 0.05 mg·L⁻¹.

•

This proposed TAD-based colorimetric method using permanganate as color reagent showed excellent performance in SAL detection with good accuracy and high precision.

Multifunctional nanomaterials and nanocomposites for sensing and monitoring of environmentally hazardous heavy metal contaminants

The applications of conventional sensors are limited by the long response time, high cost, large detection limit, low sensitivity, complicated usage and low selectivity. These sensors are nowadays replaced by Nanocomposite-based modalities and nanomaterials which are known for their high selectivity and physical and chemical properties. These nanosensors effectively detect heavy metal contaminants in the environment as the discharge of heavy metals into natural water as a result of human activity has become a global epidemic. Exposure to these toxic metals might induce many health-related complications, including kidney failure, brain injury, immune disorders, muscle paleness, cardiac damage, nervous system impairment and limb paralysis. Therefore, designing and developing novel sensing systems for the detection and recognition of these harmful metals in various environmental matrices, particularly water, is of extremely important. Emerging nanotechnological approaches in the past two decades have played a key role in overcoming environmentally-related problems. Nanomaterial-based fabrication of chemical nanosensors has widely been applied as a powerful analytical tool for sensing heavy metals. Portability, high sensitivity, on-site detection capability, better device performance and selectivity are all advantages of these nanosensors. The detection and selectivity have been improved using molecular recognition probes for selective binding on different nanostructures. This study aims to evaluate the sensing properties of various nanomaterials such as metal-organic frameworks, fluorescent materials, metal-based nanoparticles, carbon-based nanomaterials and quantum dots and graphene-based nanomaterials and quantum dots for heavy metal ions recognition. All these nano-architectures are frequently served as effective fluorescence probes to directly (or by modification with some large or small biomolecules) sense heavy metal ions for improved selectivity. However, efforts are still needed for the simultaneous designing of multiple metal ion-based detection systems, exclusively in colorimetric or optical fluorescence nanosensors for heavy metal cations.

Conductive electrospun composite fibers based on solid-state polymerized Poly(3,4-ethylenedioxythiophene) for simultaneous electrochemical detection of metal ions

Conductive composite fibers containing poly (3,4-ethylenedioxythiophene) (PEDOT) and silver nanoparticles (AgNPs) were fabricated by emulsion electrospinning of 2,5-dibromo-3,4-ethylenedioxythiophene (DBEDOT) in toluene together with aqueous solution of poly (vinyl alcohol) (PVA) and silver nanoparticles (AgNPs) in the presence of sodium dodecylsulfate followed by heat treatment at 70 °C to convert DBEDOT to conductive PEDOT via solid state polymerization (SSP). The composite fibers were characterized by scanning electron microscopy, transmission electron microscopy, x-ray photoelectron spectroscopy and thermogravimetric analysis. The PEDOT/PVA/AgNPs composite fibers deposited on a screen-printed carbon electrode (SPCE) surface exhibited good electrochemical response and was applied for simultaneous detection of heavy metal ions in a mixture, namely Zn(II), Cd(II), and Pb(II) via square wave anodic stripping voltammetry (SWASV). With added Bi⁺³ into the detection system, the bismuth film formed on the electrode allows effective alloy formation with the deposited heavy metals obtained upon reduction of the heavy metal ions, the detection of heavy metal ions after stripping was successfully accomplished with a linear range of 10-80 ppb and limits of detections (LOD) of 6, 3 and 8 ppb for Zn(II), Cd(II), and Pb(II), respectively.

A high performance Pb(II) electrochemical sensor based on spherical CuS nanoparticle anchored g-C3N4

A new electrochemical sensor has been constructed for ultra-sensitive detection of lead ions (Pb²⁺) by square wave anodic stripping voltammetry (SWASV), based on the copper sulfide/graphitic carbon nitride nanocomposite modified glassy carbon electrode (CuS/g-C₃N₄/GCE). First, spherical CuS nanoparticles with good electrical conductivity were anchored on layered g-C₃N₄ with high coordination activity, affording an excellent electrode modifier CuS/g-C₃N₄ nanocomposite. Then, the performance of the CuS/g-C₃N₄/GCE and its electrochemical response to Pb²⁺ were thoroughly studied, and the sensing mechanism was investigated. On the one hand, the CuS/g-C₃N₄ nanocomposite has greatly improved the electron transportation and electrode performance through functional complementarity - CuS endows g-C₃N₄ with a good electrical conductivity and a large active specific surface area, while g-C₃N₄ endows CuS with high dispersibility and strong adsorption. On the other hand, the CuS/g-C₃N₄ modifier has effectively promoted the deposition of trace Pb²⁺ from the solution onto the electrode surface by means of synergistic enrichment (crucial for amplification of detection signals) - g-C₃N₄ can coordinate with Pb²⁺ by its large number of conjugated triazine heterocyclic rings in its molecular framework, while CuS can adsorb Pb²⁺ due to its inherent size effect of nanomaterials. The proposed sensor can efficiently detect Pb²⁺ in the concentration range of 0.050-5.000 μM with a limit of detection (LOD) as low as 4.00 nM, and can be well applied for the detection of trace Pb²⁺ in actual tea samples.

A nanostructured microfluidic device for plasmon-assisted electrochemical detection of hydrogen peroxide released from cancer cells

Non-invasive liquid biopsies offer hope for a rapid, risk-free, real-time glimpse into cancer diagnostics. Recently, hydrogen peroxide (H₂O₂) was identified as a cancer biomarker due to its continued release from cancer cells compared to normal cells. The precise monitoring and quantification of H₂O₂ are hindered by its low concentration and the limit of detection (LOD) in traditional sensing methods. Plasmon-assisted electrochemical sensors with their high sensitivity and low LOD make a suitable candidate for effective detection of H₂O₂, yet their electrical properties need to be improved. Here, we propose a new nanostructured microfluidic device for ultrasensitive, quantitative detection of H₂O₂ released from cancer cells in a portable fashion. The fluidic device features a series of self-organized gold nanocavities, enhanced with graphene nanosheets having optoelectrical properties, which facilitate the plasmon-assisted electrochemical detection of H₂O₂ released from human cells. Remarkably, the device can successfully measure the released H₂O₂ from breast cancer (MCF-7) and prostate cancer (PC3) cells in human plasma. Briefly, direct amperometric detection of H₂O₂ under simulated visible light illumination showed a superb LOD of 1 pM in a linear range of 1 pM-10 μM. We thoroughly studied the formation of self-organized plasmonic nanocavities on gold electrodes via surface and photo-electrochemical characterization techniques. In addition, the finite-difference time domain (FDTD) simulation of the electric field demonstrates the intensity of charge distribution at the nanocavity structure edges under visible light illumination. The superb LOD of the proposed electrode combining gold plasmonic nanocavities and graphene sheets paves the way for the development of non-invasive plasmon-assisted electrochemical sensors that can effectively detect low concentrations of H₂O₂ released from cancer cells.

Development of electrochemical biosensors for simultaneous multiplex detection of microRNA for breast cancer screening

A highly sensitive electrochemical biosensors has been developed for the detection of multiplex micro ribonucleic acids (miRNAs) by modifying an electrode with reduced graphene oxide/poly(2-aminobenzylamine)/gold nanoparticles and adopting porous, hollow silver-gold nanoparticles as tagged labeling with metal ions. In addition, an anti-deoxyribonucleic acid (DNA)-RNA hybrid [S9.6] antibody was used to detect different hybridized capture DNAs and miRNAs that can detect multiple miRNAs simultaneously. The developed electrochemical platform exhibits high selectivity, stability, and sensitivity with a wide linear range from 1 fM to 10 nM and a low detection limit of 0.98 fM, 3.58 fM, and 0.25 fM for miRNA-155, miRNA-21, and miRNA-16, respectively. In addition, the proposed electrochemical biosensor capable for the simultaneous detection of miRNA-155, miRNA-16, and miRNA-21, which are breast cancer biomarkers, in normal human serum, can be adopted and potentially used for breast cancer screening.

Design and development of a portable resistive sensor based on α-MnO2 /GQD nanocomposites for trace quantification of Pb(II) in water

The occurrence of heavy metal ions in food chain is appearing to be a major problem for mankind. The traces of heavy metals, especially Pb(II) ions present in water bodies remains undetected, untreated, and it remains in the food cycle causing serious health hazards for human and livestock. The consumption of Pb(II) ions may lead to serious medical complications including multiple organ failure which can be fatal. The conventional methods of heavy metal detection are costly, time-consuming and require laboratory space. There is an immediate need to develop a cost-effective and portable sensing system which can easily be used by the common man without any technical knowhow. A portable resistive device with miniaturized electronics is developed with microfluidic well and α-MnO2 /GQD nanocomposites as a sensing material for the sensitive detection of Pb(II). α-MnO2 /GQD nanocomposites which can be easily integrated with the miniaturized electronics for real-time on-field applications. The proposed sensor exhibited a tremendous potential to be integrated with conventional water purification appliances (household and commercial) to give an indication of safety index for the drinking water. The developed portable sensor required low sample volume (200 µL) and was assessed within the Pb(II) concentration range of 0.001 nM to 1 uM. The Limit of Detection (LoD) and sensitivity was calculated to be 0.81 nM and 1.05 kΩ/nM/mm2 , and was validated with the commercial impedance analyser. The shelf-life of the portable sensor was found to be ∼45 days.

Electrospun Nanofibers and Electrochemical Techniques for the Detection of Heavy Metal Ions

Contamination by heavy metals is currently one of the most environmental concerns especially due to the toxicity, pervasiveness, and persistence of these substances. As they are not biodegradable, heavy metals are harmful not only for water, air, and soil but also for human health, even in very low traces. There is therefore a pressing need to develop an efficient, economic, and rapid analysis method to be applied in a wide range of conditions and able to detect very low contaminants concentrations. Currently, the most novel solution in this field is represented by the combination of electrospun nanofibers and highly sensitive electrochemical techniques. It has been proved that nanofibers, due to their outstanding properties, perfectly fit as sensing material when trace concentrations of heavy metals were investigated by anodic stripping voltammetry, envisaged as the most sensitive electrochemical technique for this kind of measurements. This work aims to provide an overview of the latest trends in the detection of contaminants by the simultaneous use of electrospun fibers and anodic stripping voltammetry. Indeed, a clear and comprehensive vision of the current status of this research may drive future improvements and new challenges.

Carbon Nanomaterials: Synthesis, Functionalization and Sensing Applications

Recent advances in nanomaterial design and synthesis has resulted in robust sensing systems that display superior analytical performance. The use of nanomaterials within sensors has accelerated new routes and opportunities for the detection of analytes or target molecules. Among others, carbon-based sensors have reported biocompatibility, better sensitivity, better selectivity and lower limits of detection to reveal a wide range of organic and inorganic molecules. Carbon nanomaterials are among the most extensively studied materials because of their unique properties spanning from the high specific surface area, high carrier mobility, high electrical conductivity, flexibility, and optical transparency fostering their use in sensing applications. In this paper, a comprehensive review has been made to cover recent developments in the field of carbon-based nanomaterials for sensing applications. The review describes nanomaterials like fullerenes, carbon onions, carbon quantum dots, nanodiamonds, carbon nanotubes, and graphene. Synthesis of these nanostructures has been discussed along with their functionalization methods. The recent application of all these nanomaterials in sensing applications has been highlighted for the principal applicative field and the future prospects and possibilities have been outlined.

Poly(1,5-Diaminonaphthalene)-Modified Screen-Printed Device for Electrochemical Lead Ion Sensing

Poly(1,5-diaminonaphthalene) has been electropolymerized on the screen-printed device with a three-electrode configuration. The modified electrodes have been developed as the new electrode for electrochemical determination of trace levels of lead ions (Pb2+). The poly(1,5-diaminonaphthalene) film prevents the deposition of Pb2+ into the surface defects of the bare carbon screen-printed electrode and possesses sensitivity to heavy metal ions thanks to amine and secondary amino groups on the polymer chain. The square wave anodic stripping voltammetry was applied to detect Pb2+ ions, showing a sharp stripping peak with the linear range from 0.5 μg·L-1 to 5.0 μg·L-1 ( $R^2=0.9929$ ). The limit of detection was found to be 0.30 μg·L-1. The sensors were applied to the analysis of Pb2+ in the tap water sample matrix with satisfactory results.

Studying the preparation, electrochemical performance testing, comparison and application of a cost-effective flexible graphene working electrode

-A cost-effective flexible graphene working electrode (FGWE) was fabricated using overhead projector transparent film (OPTF) and a screen-printing technique. The surface morphology and electrochemical behavior of the electrode were characterized by scanning electron microscopy and cyclic voltammetry. The electrode presented a very thin layer of conductive ink (16.0 ± 0.7 µm) on a large effective surface area (0.301 ± 0.001 cm^-2). The anodic peak current density (j_pa) of acetaminophen (ACT) in FGWE was 5.2, 3.7, 3.5 and 6.0 times greater than the j_pa of glassy carbon electrode (GCE), flexible carbon working electrode (FCWE), SPE1, and SPE2, respectively. The electrochemical performance of FGWE toward ACT was evaluated by differential pulse voltammetry. Under optimized condition, ACT was quantified in a range of  4-100 µM, with good sensitivity, good accuracy (recovery = 82.3 ± 0.4 to 106 ± 3%), and excellent precision. FGWE was applied to determine ACT in commercial pharmaceutical formulations. The results of the study are in good agreement with those obtained by the standard spectrophotometric method. These results indicate that disposable FGWE is particularly useful for the detection of ACT, and its performance may serve as a platform for cost-effective flexible electrochemical sensors.

Label-free anti-Müllerian hormone sensor based on polyaniline micellar modified electrode

A label-free electrochemical immunosensor based on polyaniline (PANI) micellar electrode was firstly fabricated for direct AMH detection. To control the size regularity of PANI, a micelle-based method using ammonium peroxydisulfate (APS) as a reducing agent was employed in the polymerization process. The Anti-AMH antibodies were readily immobilized onto PANI via peptide bond to enhance the sensor specificity and sensitivity. This sensor was applied for the detection of AMH, an ovarian response indicator in female related to residual eggs during a woman's monthly cycle. The sensor performances were systematically investigated by differential pulse voltammetry. The anodic peak current decreases with the increase of AMH concentration owing to blocking of electron transfer by AMH. Under the optimal conditions, this sensor offers high sensitivity with a low detection limit of 0.1 ng mL^-1 and a wide linear range of 0.1-4 ng mL^-1, which is sensitive enough to indicate the ability to produce eggs during a woman's monthly cycle. Furthermore, this system requires lower sample volume (5 μL), while offers the simple fabrication with low cost and no synthetic challenge and faster analysis compared with a standard ELISA. Ultimately, this sensor was successfully applied for the detection of AMH in human serum with satisfactory results. Thus, it might be an alternative tool for AMH screening in clinical setting.

Recent Developments in Polymer Nanocomposite-Based Electrochemical Sensors for Detecting Environmental Pollutants

The human population is generally subjected to diverse pollutants and contaminants in the environment like those in the air, soil, foodstuffs, and drinking water. Therefore, the development of novel purification techniques and efficient detection devices for pollutants is an important challenge. To date, experts in the field have designed distinctive analytical procedures for the detection of pollutants including gas chromatography/mass spectrometry and atomic absorption spectroscopy. While the mentioned procedures enjoy high sensitivity, they suffer from being laborious, expensive, require advanced skills for operation, and are inconvenient to deploy as a result of their massive size. Therefore, in response to the above-mentioned limitations, electrochemical sensors are being developed that enjoy robustness, selectivity, sensitivity, and real-time measurements. Considerable advancements in nanomaterials-based electrochemical sensor platforms have helped to generate new technologies to ensure environmental and human safety. Recently, investigators have expanded considerable effort to utilize polymer nanocomposites for building the electrochemical sensors in view of their promising features such as very good electrocatalytic activities, higher electrical conductivity, and effective surface area in comparison to the traditional polymers. Herein, the first section of this review briefly discusses the most important methods for polymer nanocomposites synthesis, such as in situ polymerization, direct mixing of polymer and nanofillers (melt-mixing and solution-mixing), sol-gel, and electrochemical methods. It then summarizes the current utilization of polymer nanocomposites for the preparation of electrochemical sensors as a novel approach for monitoring and detecting environmental pollutants which include heavy metal ions, pesticides, phenolic compounds, nitroaromatic compounds, nitrite, and hydrazine in different mediums. Finally, the current challenges and future directions for the polymer nanocomposites-based electrochemical sensing of environmental pollutants are outlined.

Portable Real-Time Detection of Pb(II) Using a CMOS MEMS-Based Nanomechanical Sensing Array Modified with PEDOT:PSS

Detecting the concentration of Pb²⁺ ions is important for monitoring the quality of water due to it can become a health threat as being in certain level. In this study, we report a nanomechanical Pb²⁺ sensor by employing the complementary metal-oxide-semiconductor microelectromechanical system (CMOS MEMS)-based piezoresistive microcantilevers coated with PEDOT:PSS sensing layers. Upon reaction with Pb²⁺, the PEDOT:PSS layer was oxidized which induced the surface stress change resulted in a subsequent bending of the microcantilever with the signal response of relative resistance change. This sensing platform has the advantages of being mass-produced, miniaturized, and portable. The sensor exhibited its sensitivity to Pb²⁺ concentrations in a linear range of 0.01–1000 ppm, and the limit of detection was 5 ppb. Moreover, the sensor showed the specificity to Pb²⁺, required a small sample volume and was easy to operate. Therefore, the proposed analytical method described here may be a sensitive, cost-effective and portable sensing tool for on-site water quality measurement and pollution detection.