Preparation of hexagonal boron nitride doped graphene film modified sensor for selective electrochemical detection of nicotine in tobacco sample

A nitrogen-doped carbon nanosheet/poly(amidoamine) dendrimer-based electrochemical sensor for nicotine in flavored hookah pipe tobacco

Towards the nicotine addiction challenge in the smoking of hookah pipe products, we hereby present the development of an electrochemical sensor for nicotine detection. A nitrogen-doped carbon nanosheet (N-CNS)/poly(amidoamine) dendrimer (PAMAM) nanocomposite-modified electrode was prepared as a sensor for the detection of nicotine in analytical and real samples. The N-CNSs were prepared by a hydrothermal method and dropcast on a glassy carbon electrode followed by electro-deposition of the PAMAM dendrimer to form the sensor (GCE/N-CNSs/PAMAM). The N-CNSs were characterized with electron microscopy, Raman spectroscopy and FTIR. The sensor was characterized with voltammetry and electrochemical impedance spectroscopy. The N-CNS/PAMAM enhanced the electrochemical performance of the electrode towards the oxidation of nicotine. The sensor achieved a detection limit of 0.05 μM in a linear concentration range of 1.93-61.64 μM nicotine standard samples. The sensor showed good reproducibility, repeatability, and selectivity. The sensor was successful in selectively detecting nicotine in two local brands of hookah pipe tobacco with a 113-121 percent recovery. Nicotine, up to a concentration of 0.35-0.39 mg g-1, was found in the sampled hookah pipe tobacco products suggesting possible harm to human health.

Emerging trends in functional materials for electrochemical sensors in nicotine determination

In the past year, there has been significant progress in the utilization of electrochemical strategies for the determination of harmful substances. Among those, the electrochemical determination of nicotine (NIC) has continued to be of significant interest ascribed to the global health concern of e-cigarette products, nowadays. Electrochemical sensors have become promising tools for the detection of NIC ascribed to their high sensitivity, selectivity, and ease of use. This review article provides a concise overview of the advanced developments in electrochemical sensors for NIC detection using modified functional materials such as carbon-based materials, metal-organic frameworks (MOF), MXene, polymer, and metallic based modifiers. The sensitivity of electrochemical sensors can be improved by modifying them with these conductive materials ascribed to their physical and chemical properties. The review also addresses the challenges and future perspectives in the field, including sensitivity and selectivity improvements, stability and reproducibility issues, integration with data analysis techniques, and emerging trends. In conclusion, this review article may be of interest to researchers intending to delve into the development of functional electrochemical sensors in future studies.

Construction of Cu2Y2O5/g-C3N4 Novel Composite for the Sensitive and Selective Trace-Level Electrochemical Detection of Sulfamethazine in Food and Water Samples

The most frequently used sulfonamide is sulfamethazine (SMZ) because it is often found in foods made from livestock, which is hazardous for individuals. Here, we have developed an easy, quick, selective, and sensitive analytical technique to efficiently detect SMZ. Recently, transition metal oxides have attracted many researchers for their excellent performance as a promising sensor for SMZ analysis because of their superior redox activity, electrocatalytic activity, electroactive sites, and electron transfer properties. Further, Cu-based oxides have a resilient electrical conductivity; however, to boost it to an extreme extent, a composite including two-dimensional (2D) graphitic carbon nitride (g-C3N4) nanosheets needs to be constructed and ready as a composite (denoted as g-C3N4/Cu2Y2O5). Moreover, several techniques, including X-ray diffraction analysis, scanning electron microscopy analysis, energy-dispersive X-ray spectroscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy were employed to analyze the composites. The electrochemical measurements have revealed that the constructed g-C3N4/Cu2Y2O5 composites exhibit great electrochemical activity. Nevertheless, the sensor achieved outstanding repeatability and reproducibility alongside a low limit of detection (LOD) of 0.23 µM, a long linear range of 2 to 276 µM, and an electrode sensitivity of 8.86 µA µM-1 cm-2. Finally, the proposed GCE/g-C3N4/Cu2Y2O5 electrode proved highly effective for detection of SMZ in food samples, with acceptable recoveries. The GCE/g-C3N4/Cu2Y2O5 electrode has been successfully applied to SMZ detection in food and water samples.

Recent advances in graphene-based electroanalytical devices for healthcare applications

Graphene, with its outstanding mechanical, electrical, and biocompatible properties, stands out as an emerging nanomaterial for healthcare applications, especially in building electroanalytical biodevices. With the rising prevalence of chronic diseases and infectious diseases, such as the COVID-19 pandemic, the demand for point-of-care testing and remote patient monitoring has never been greater. Owing to their portability, ease of manufacturing, scalability, and rapid and sensitive response, electroanalytical devices excel in these settings for improved healthcare accessibility, especially in resource-limited settings. The development of different synthesis methods yielding large-scale graphene and its derivatives with controllable properties, compatible with device manufacturing - from lithography to various printing methods - and tunable electrical, chemical, and electrochemical properties make it an attractive candidate for electroanalytical devices. This review article sheds light on how graphene-based devices can be transformative in addressing pressing healthcare needs, ranging from the fundamental understanding of biology in in vivo and ex vivo studies to early disease detection and management using in vitro assays and wearable devices. In particular, the article provides a special focus on (i) synthesis and functionalization techniques, emphasizing their suitability for scalable integration into devices, (ii) various transduction methods to design diverse electroanalytical device architectures, (iii) a myriad of applications using devices based on graphene, its derivatives, and hybrids with other nanomaterials, and (iv) emerging technologies at the intersection of device engineering and advanced data analytics. Finally, some of the major hurdles that graphene biodevices face for translation into clinical applications are discussed.

Sensitive detection of choline and nicotine in real samples by switching upconversion luminescence

Nicotine (3-(1-methyl-2-pyrrolidinyl)pyridine) is one of the most common addictive substances, causing the trace detection of nicotine to be very necessary. Herein, we designed and prepared a functionalized nanocomposite CS-PAA (NaYF4:19.5%Yb,0.5%Tm@NaYF4-PAA) using a simple method. The nicotine concentration was quantitatively detected through the inhibition of choline oxidase activity by nicotine and the luminescence intensity of CS-PAA being quenched by Fe3+. The mechanism of Fe3+ quenching CS-PAA emission was inferred by luminescence lifetime and UV-vis absorption spectra characterization. During the nicotine detection, both excitation (980 nm) and emission (802 nm) wavelengths of CS-PAA enable the avoidance of the interference of background fluorescence in complicated food objects, thus providing high selectivity and sensitivity with a linear range of 5-750 ng/mL and a limit of detection of 9.3 nM. The method exhibits an excellent recovery and relative standard deviation, indicating high accuracy and repeatability of the detection of nicotine.

Highly Sensitive Detection of Hydrogen Peroxide in Cancer Tissue Based on 3D Reduced Graphene Oxide-MXene-Multi-Walled Carbon Nanotubes Electrode

Hydrogen peroxide (H2O2) is a signaling molecule that has the capacity to control a variety of biological processes in organisms. Cancer cells release more H2O2 during abnormal tumor growth. There has been a considerable amount of interest in utilizing H2O2 as a biomarker for the diagnosis of cancer tissue. In this study, an electrochemical sensor for H2O2 was constructed based on 3D reduced graphene oxide (rGO), MXene (Ti3C2), and multi-walled carbon nanotubes (MWCNTs) composite. Three-dimensional (3D) rGO-Ti3C2-MWCNTs sensor showed good linearity for H2O2 in the ranges of 1-60 μM and 60 μM-9.77 mM at a working potential of -0.25 V, with sensitivities of 235.2 µA mM-1 cm-2 and 103.8 µA mM-1 cm-2, respectively, and a detection limit of 0.3 µM (S/N = 3). The sensor exhibited long-term stability, good repeatability, and outstanding immunity to interference. In addition, the modified electrode was employed to detect real-time H2O2 release from cancer cells and cancer tissue ex vivo.

Developments in conducting polymer-, metal oxide-, and carbon nanotube-based composite electrode materials for supercapacitors: a review

Supercapacitors are the latest development in the field of energy storage devices (ESDs). A lot of research has been done in the last few decades to increase the performance of supercapacitors. The electrodes of supercapacitors are modified by composite materials based on conducting polymers, metal oxide nanoparticles, metal-organic frameworks, covalent organic frameworks, MXenes, chalcogenides, carbon nanotubes (CNTs), etc. In comparison to rechargeable batteries, supercapacitors have advantages such as quick charging and high power density. This review is focused on the progress in the development of electrode materials for supercapacitors using composite materials based on conducting polymers, graphene, metal oxide nanoparticles/nanofibres, and CNTs. Moreover, we investigated different types of ESDs as well as their electrochemical energy storage mechanisms and kinetic aspects. We have also discussed the classification of different types of SCs; advantages and drawbacks of SCs and other ESDs; and the use of nanofibres, carbon, CNTs, graphene, metal oxide-nanofibres, and conducting polymers as electrode materials for SCs. Furthermore, modifications in the development of different types of SCs such as pseudo-capacitors, hybrid capacitors, and electrical double-layer capacitors are discussed in detail; both electrolyte-based and electrolyte-free supercapacitors are taken into consideration. This review will help in designing and fabricating high-performance supercapacitors with high energy density and power output, which will act as an alternative to Li-ion batteries in the future.

Application of dandelion-like Sm2O3/Co3O4/rGO in high performance supercapacitors

Novel 2D material-based supercapacitors are promising candidates for energy applications due to their distinctive physical, chemical, and electrochemical properties. In this study, a dandelion-like structure material comprised of Sm2O3, Co3O4, and 2D reduced graphene oxide (rGO) on nickel foam (NF) was synthesised using a hydrothermal method followed by subsequent annealing treatment. This dandelion composite grows further through the tremella-like structure of Sm2O3 and Co3O4, which facilitates the diffusion of ions and prevents structural collapse during charging and discharging. A substantial number of active sites are generated during redox reactions by the unique surface morphology of the Sm2O3/Co3O4/rGO/NF composite (SCGN). The maximum specific capacity the SCGN material achieves is 3448 F g-1 for 1 A g-1 in a 6 mol L-1 KOH solution. Benefiting from its morphological structure, the prepared composite (SCGN) exhibits a high cyclability of 93.2% over 3000 charge-discharge cycles at 10 A g-1 and a coulombic efficiency of 97.4%. Additionally, the assembled SCGN//SCGN symmetric supercapacitors deliver a high energy density of 64 W h kg-1 with a power density of 300 W kg-1, which increases to an outstanding power density of 12 000 W kg-1 at 28.7 W h kg-1 and long cycle stability (80.9% capacitance retention after 30 000 cycles). These results suggest that the manufactured SCGN electrodes could be viable active electrode materials for electrochemical supercapacitors.

A core-molecule-shell Au@PATP@Ag nanorod for nicotine detection based on surface-enhanced Raman scattering technology

Nicotine is an addictive substance often found in tobacco and cigarette smoke and excessive exposure to it can cause various diseases. Herein, core-molecule-shell gold/4-aminothiophenol/silver nanorods (Au@PATP@Ag NRs) were prepared for quantitative detection of nicotine by using surface-enhanced Raman scattering (SERS) technology. The obtained Au@PATP@Ag NRs showed an outstanding SERS effect due to the plasticity of their morphology and the bimetallic synergistic effect between the excellent stability of Au and the highly enhanced effect of Ag. The Au@PATP@Ag NRs substrate exhibited an extremely high enhancement factor (EF) of 2.17 × 107. In addition, in-situ synthesized PATP was used as an internal standard to correct signal fluctuation and improve the reliability of quantitative nicotine detection. A wide linear dynamic range from 10-8 to 10-3 M was obtained and an ultra-low limit of detection (LOD) was about 3.12 × 10-9 M, which was superior to most of previously reported methods. This work has also been used for determining nicotine content in cigarettes and simulated environmental tobacco smoke by using a portable device. These results indicated that the developed SERS method had many potential applications in the quantitative determination of nicotine in real tobacco samples.

Development of Electrochemical Sensor Using Iron (III) Phthalocyanine/Gold Nanoparticle/Graphene Hybrid Film for Highly Selective Determination of Nicotine in Human Salivary Samples

Nicotine is the one of the major addictive substances; the overdose of nicotine (NIC) consumption causes increasing heart rate, blood pressure, stroke, lung cancer, and respiratory illnesses. In this study, we have developed a precise and sensitive electrochemical sensor for nicotine detection in saliva samples. It was built on a glassy carbon electrode (GCE) modified with graphene (Gr), iron (III) phthalocyanine-4,4',4″,4'''-tetrasulfonic acid (Fe(III)Pc), and gold nanoparticles (AuNPs/Fe(III)Pc/Gr/GCE). The AuNPs/Fe(III)Pc/Gr nanocomposite was prepared and characterized by using FE-SEM, EDX, and E-mapping techniques to confirm the composite formation as well as the even distribution of elements. Furthermore, the newly prepared AuNPs/Fe(III)Pc/Gr/GCE-nanocomposite-based sensor was used to detect the nicotine in phosphate-buffered solution (0.1 M PBS, pH 7.4). The AuNPs/Fe(III)Pc/Gr/GCE-based sensor offered a linear response against NIC from 0.5 to 27 µM with a limit of detection (LOD) of 17 nM using the amperometry (i-t curve) technique. This electrochemical sensor demonstrated astounding selectivity and sensitivity during NIC detection in the presence of common interfering molecules in 0.1 M PBS. Moreover, the effect of pH on NIC electro-oxidation was studied, which indicated that PBS with pH 7.4 was the best medium for NIC determination. Finally, the AuNPs/Fe(III)Pc/Gr/GCE sensor was used to accurately determine NIC concentration in human saliva samples, and the recovery percentages were also calculated.

Amperometric determination of salivary thiocyanate using electrochemically fabricated poly (3, 4-ethylenedioxythiophene)/MXene hybrid film

Thiocyanate (SCN) is a hazardous byproduct of the detoxification of cyanide. Even in minute quantity, the SCN has a negative impact on health. Although there are several ways for SCN analysis, an efficient electrochemical procedure has hardly ever been attempted. Here, the author reports the development of a highly selective and sensitive electrochemical sensor for SCN utilizing Poly (3, 4-Ethylenedioxythiophene) incorporated MXene (PEDOT/MXene) modified screen-printed electrode (SPE). The Raman, X-ray photoelectron (XPS), and X-ray diffraction (XRD) analyses support the effective integration of PEDOT on the MXene surface. Further, scanning electron microscopy (SEM) is employed to demonstrate the formation of MXene and PEDOT/MXene hybrid film. In order to specifically detect SCN in phosphate buffer media (pH 7.4), the PEDOT/MXene hybrid film is grown on the SPE surface via the electrochemical deposition method. Under the optimized condition, the PEDOT/MXene/SPE-based sensor provides a linear response against SCN from 10 to 100 µM and 0.1 μM to 1000 μM with the lowest limit of detections (LOD) of 1.44 μM and 0.0325 μM by differential pulse voltammetry (DPV) and amperometry, respectively. For accurate detection of SCN, our newly created PEDOT/MXene hybrid film-coated SPE demonstrates excellent sensitivity, selectivity, and repeatability. Ultimately, this novel sensor can be used to detect SCN precisely in environmental and biological samples.

Ru(II)-modified metal organic framework as excellent electrochemiluminescence emitter for ultrasensitive nicotine detection

The sensitive and selective nicotine detection in cigarette is necessary due to the cigarette addiction problem and the neurotoxicity of nicotine on human body. In this study, a novel electrochemiluminescence (ECL) emitter with excellent performance was prepared for nicotine analysis, by combining Zr-based metal organic framework (Zr-MOF) and branched polyethylenimine (BPEI)-coated Ru(dcbpy)₃²⁺ through electrostatic interaction. Ru(dcbpy)₃²⁺ integrated by Zr-MOF could be catalyzed by the reaction intermediates SO₄^•-, produced from the co-reactant S₂O₈^2-, resulting in a significant increase in ECL response. Interestingly, SO₄^•- with strong oxidizing ability could preferentially oxidize nicotine, leading to ECL quenching. The constructed ECL sensor based on the Ru-BPEI@Zr-MOF/S₂O₈^2- system displayed ultrasensitive determination of nicotine with a lower detection limit of 1.9 × 10^-12 M (S/N = 3), which is three orders lower than previously reported ECL results and 4-5 orders lower than that of other types of method. This method puts forward a new approach for building efficient ECL system with greatly improved ECL sensitivity for nicotine detection.

In situ synthesis of polythiophene encapsulated 2D hexagonal boron nitride nanocomposite based electrochemical transducer for detection of 5-fluorouracil with high selectivity

It is difficult for the scientific community to develop a nonenzymatic sensing platform for extremely sensitive and selective detection of specific biomolecules, antibiotics, food adulterants, heavy metals, etc. One of the most significant chemotherapy drugs, 5-fluorouracil (5-Fu), which is used to treat solid malignancies, has a fluorine atom in the fifth position of the uracil molecule. Recognizing the secure and effective dosing of drugs for chemotherapy continues to be a critical concern in cancer disease management. The maintenance of the optimal 5-Fu concentration is dependent on the presence of 5-Fu in biofluids. Herein we reported a conducting polymer encapsulated 2D material, PTh/h-BN for the efficient electrochemical detection of anticancer drug 5-Fu. Furthermore, the synthesized PTh/h-BN nanocomposite was confirmed by the High-Resolution Transmission Electron Microscope (HR-TEM), High-Resolution Scanning Electron Microscope (HR-SEM), X-ray diffraction (XRD), and Fourier-Transform Infrared Spectroscopy (FT-IR). The electrical resistance of PTh/h-BN modified GCE and its sensing performance towards 5-Fu were tested using Electrochemical Impedance Spectroscopy (EIS) and Cyclic Voltammetry (CV) studies respectively. The analytical performance of our proposed catalyst was tested using Differential Pulse Voltammetry (DPV), and the amperometry (i-t curve) method. From the results, our proposed PTh/h-BN nanocomposite-modified GCE shows enhanced sensing performance due to higher redox peak currents, large active surface area, and high electrical conductivity. Moreover, the nanohybrid shows enhanced sensing performances with quick response time, wide linear range, the lowest limit of detection, high sensitivity, and high selectivity in the presence of various interferents. Finally, the practical applicability of the proposed sensor was tested with real-world samples with very good recovery percentages.

A novel spectrophotometric method based on plasmonic nanoparticles for nicotine detection

In this paper, a spectrophotometric method for nicotine detection based on plasmonic nanoparticles (AuNPs and AgNPs) is proposed. Due to their specific properties, plasmonic nanoparticles have become interesting to use in the development of sensitive analytical methods. The localized surface plasmon resonance (LSPR) absorption bands for AgNPs and AuNPs with a wavelength at 395.5 nm (A_395.5) and 543.5 (A_543.5) nm, respectively, are used for the detection. Experimental variables such as solvent type and pH were optimized so as to determine the optimum working conditions. The analytical calibration curve for both AgNPs and AuNPs based on spectrophotometric methods was prepared with nicotine concentrations range from 0.10 to 5.00 μM (R² = 0.9903) and 0.001-0.300 μM (R² = 0.9960), respectively. The detection limits were found to be 0.001 µM for AuNPs based method and 0.09 µM for AgNPs based method. The proposed nanoparticle-based spectrophotometric methods showed a good stability, selectivity and low detection limit.

Palladium Hydroxide (Pearlman's Catalyst) Doped MXene (Ti3C2Tx) Composite Modified Electrode for Selective Detection of Nicotine in Human Sweat

High concentrations of nicotine (40 to 60 mg) are more dangerous for adults who weigh about 70 kg. Herein, we developed an electrochemical transducer using an MXene (Ti₃C₂Tx)/palladium hydroxide-supported carbon (Pearlman's catalyst) composite (MXene/Pd(OH)₂/C) for the identification of nicotine levels in human sweat. Firstly, the MXene was doped with Pd(OH)₂/C (PHC) by mechanical grinding followed by an ultrasonication process to obtain the MXene/PHC composite. Secondly, XRD, Raman, FE-SEM, EDS and E-mapping analysis were utilized to confirm the successful formation of MXene/PHC composite. Using MXene/PHC composite dispersion, an MXene/PHC composite-modified glassy carbon electrode (MXene/PHC/GCE) was prepared, which showed high sensitivity as well as selectivity towards nicotine (300 µM NIC) oxidation in 0.1 M phosphate buffer (pH = 7.4) by cyclic voltammetry (CV) and amperometry. The MXene/PHC/GCE had reduced the over potential of nicotine oxidation (about 200 mV) and also enhanced the oxidation peak current (8.9 µA) compared to bare/GCE (2.1 µA) and MXene/GCE (5.5 µA). Moreover, the optimized experimental condition was used for the quantification of NIC from 0.25 µM to 37.5 µM. The limit of detection (LOD) and sensitivity were 27 nM and 0.286 µA µM^-1 cm², respectively. The MXene/PHC/GCE was also tested in the presence of Na⁺, Mg²⁺, Ca²⁺, hydrogen peroxide, acetic acid, ascorbic acid, dopamine and glucose. These molecules were not interfered during NIC analysis, which indicated the good selectivity of the MXene/PHC/GCE sensor. In addition, electrochemical determination of NIC was successfully carried out in the human sweat samples collected from a tobacco smoker. The recovery percentage of NIC in the sweat sample was 97%. Finally, we concluded that the MXene/PHC composite-based sensor can be prepared for the accurate determination of NIC with high sensitivity, selectivity and stability in human sweat samples.

A Low-Cost Electrochemical Method for the Determination of Sulfadiazine in Aquaculture Wastewater

As the concept of green development spreads worldwide, environmental protection awareness for production and life has been continuously strengthened. Antibiotic residues in aquaculture wastewaters aggravate environmental pollution and threaten human health. Therefore, the detection of residual antibiotics in wastewater is crucial. In this paper, a new, simple, and low-cost method based on the glassy carbon electrode electrochemical sensor for the detection of sulfadiazine in aquaculture wastewater was developed without using complex materials to modify the electrode surface, to detect sulfadiazine which electrochemically oxidizes directly. The electrochemical performance of the sensor was studied and optimized with differential pulse voltammetry and cyclic voltammetry in the three-electrode system. The optimal electrolyte was acetic acid-sodium acetate buffer, and the optimal pH was 4.0. Finally, based on the optimized conditions, the newly established method showed satisfactory results for detecting sulfadiazine in aquaculture wastewater. The concentration of sulfadiazine and the peak current intensity showed a linear relationship in the range of 20 to 300 μmol/L, and the limit of detection was 6.14 μmol/L, the recovery rate of standard addition was 87-95%, with satisfactory reproducibility and low interference.

2D MXene/graphene nanocomposite preparation and its electrochemical performance towards the identification of nicotine level in human saliva

The quantitative analysis of neurological drugs is critical since the kinetics of body fluids is strongly dependent on the dosage of the drug levels. Thus, the study of neurological medicines is significant because of the major diseases connected to it, for instance, Alzheimer's and Parkinson's diseases. Herein, a 2D hybrid MXene/graphene (MX/Gr) film was synthesized through a top-down approach and utilized to prepare an electrochemical transducer for the electrochemical sensing of nicotine. The X-ray diffraction (XRD), Raman and X-ray photoelectron spectroscopy (XPS) confirmed the successful incorporation of MX with Gr sheets. The high-resolution scanning electron microscopy (HR-SEM) and transmission electron microscopy (TEM) have been used to confirm the formation of MX, graphene sheets and the MX/Gr hybrid film. Furthermore, the MX/Gr hybrid film composite modified glassy carbon electrode (GCE) was prepared to selectively detect the nicotine in phosphate buffer medium (0.1 M PBS, pH~7.4). Under the optimized condition, the MX/Gr/GCE based sensor provided a linear response against nicotine from 1 to 55 µM and 30 nM - 600 nM with the lowest limit of detections (LOD) of 290 nM and 0.28 nM by differential pulse voltammetry (DPV) and amperometry, respectively. This newly developed MX/Gr hybrid film modified electrode displayed a remarkable selectivity, sensitivity, and reproducibility for accurate detection of nicotine. Finally, this new sensor was applied to detect nicotine in human/artificial saliva samples with high accuracy.

Electrochemical detection of nicotine at a carbon Nanofiber-Poly(amidoamine) dendrimer modified glassy carbon electrode

Development of electrochemical sensors for important drugs such nicotine (an addictive drug) is important for the society. This study reports the electrochemical detection of nicotine at a carbon nanofiber/poly (amidoamine) dendrimer modified glassy carbon electrode. The carbon nanofiber (CNF) modified GCE was prepared by drop-coating followed by the electrodeposition of generation 4 poly (amidoamine) succinamic acid dendrimer (PAMAM) to form the sensor - CNF-PAMAM GCE. Characterization of prepared materials and modified electrodes was carried out using Fourier transmission infrared spectroscopy, field emission scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, cyclic voltammetry, electrochemical impedance spectroscopy (EIS) and differential pulse voltammetry (DPV). The CNF-PAMAM composite was confirmed by microscopy. A marked reduction in charge transfer resistance and increase in current of the CNF-PAMAM GCE in comparison to the bare electrode showed a synergic improvement electrochemical response because of the CNF-PAMAM nanocomposite. The CNF-PAMAM demonstrated an enhanced performance in the oxidation of nicotine in comparison to the bare GCE by shifting the anodic potential E_pa of nicotine from 0.9 V to 0.8 V. The electrochemical sensor achieved a detection limit (LOD) of 0.02637 μM in the concentration range of 0.4815-15.41 μM of nicotine in 0.1 M PBS at pH 7.5. The sensor ability to determine nicotine in real samples was assessed in cigarettes obtaining recovery percentages of 88.00 and 97.42%. The sensor demonstrated selectivity toward nicotine in the presence of interferences. Finally, the method was validated by ultraviolet-visible spectroscopy analysis.

A simple and rapid approach for on-site analysis of nicotine in tobacco based on a screen-printed electrode as an electrochemical sensor

In this study, we report a portable kit consisting of a portable workstation, gold screen-printed electrode (SPE), 0.45 μm filter membrane, phosphate buffer solution (PBS), and acetic acid (1%) for point-of-use (POU) analysis of nicotine in tobacco. The activated-screen-printed electrode (A-SPE) displayed superior electron transmission efficiency, and the A-SPE without modification was employed for high-performance analysis of nicotine in actual tobacco after simple sample pretreatment. Remarkably, the fabricated nicotine sensor exhibited a broad working range of 10-100 μg g-1, a low limit of detection (LOD) of 6.4 μg mL-1, good stability, selectivity, and practicality under the optimal conditions. The method was applied to the determination of nicotine in (spiked) samples. Satisfactory recovery results demonstrated that the as-prepared portable kit method with outstanding electrocatalysis ability was feasible for analysis of nicotine in tobacco. Moreover, the values obtained using the A-SPE were in good agreement with those determined by gas chromatography-flame ionization detection (GC-FID), which confirms the feasibility and validity of the present method. The results of the as-proposed portable kit provided a new strategy for analyzing nicotine in actual tobacco samples.

Novel electrochemical sensor modified with molecularly imprinted polymers for determination of enrofloxacin in marine environment

Molecularly imprinted polymers were synthesized by gel-sol method with multi-walled carbon nanotubes as support and enrofloxacin as a template and further modified on the surface of glassy carbon electrode to construct a molecularly imprinted electrochemical sensor. The performance of the imprinted electrochemical sensor was thoroughly investigated by using cyclic voltammetry and differential pulse voltammetry. The influence of imprinted polymers amount, electrolyte pH, and incubation time on the sensor performance was investigated for the detection of enrofloxacin. Under the optimal experimental conditions in a three-electrode system with the modified electrode as the working electrode the differential pulse voltammetry response current of the sensor had a good linear relationship at 0.2 V (vs. saturated calomel reference electrode) with the enrofloxacin concentration within 2.8 pM-28 μM and the limit of detection of the method was 0.9 pM. The competitive interference experiment showed that the imprinted electrochemical sensor could selectively recognize enrofloxacin. The method was applied to analyze spiked natural seawater, fish, and shrimp samples. The recovery was 96.4%-102%, and RSD was less than 4.3% (n = 3), indicating that the proposed imprinted electrochemical sensor was suitable for the determination of trace enrofloxacin in marine environment samples.

Preparation of 2D Graphene/MXene nanocomposite for the electrochemical determination of hazardous bisphenol A in plastic products

Bisphenol A (BPA) is one of the major contaminants with significant health hazards, which could also affect the endocrine system or induce cancer. It is essential to develop a highly sensitive and selective BPA sensor for environmental and food safety. Herein, 2D hybrid graphene/Ti₃C₂T_x nanocomposite (Gr/MXene) was prepared via a top-down method and then used to fabricate an electrochemical BPA sensor. The X-ray diffraction spectrometer (XRD) and Raman spectroscopy analysis were carried out to verify the successful formation of Gr sheets with MXene. The high resolution scanning electron microscopy (HR-SEM) was revealed the formation of MXene, and Gr/MXene nanocomposite. Furthermore, the 2D hybrid Gr/MXene nanocomposite modified glassy carbon electrode (GCE) was prepared for BPA oxidation in 100 mM phosphate buffer solution (PBS). Under the optimized condition, the Gr/MXene/GCE was displayed a linear range of detection from 10 to 180 nM and 1 to 10 μM BPA with the detection limits of 4.08 nM and 0.35 μM by amperometry and differential pulse voltammetry (DPV), respectively. Moreover, the proposed Gr/MXene modified electrode exhibited excellent stability, selectivity, repeatability and reproducibility towards the BPA detection. As a proof of concept, Gr/MXene modified sensor was effectively used to detect BPA in modern plastic products with the recovery ranging from 99.2 to 104.5%.

Highly Stable Copper Nano Cluster on Nitrogen-Doped Graphene Quantum Dots for the Simultaneous Electrochemical Sensing of Dopamine, Serotonin, and Nicotine; a Possible Addiction Scrutinizing Strategy

A highly stable copper nanocluster CuNC@N-GQD which exhibited stability for more than one year was synthesized using nitrogen doped graphene quantum dots (N-GQDs) as reducing and capping agents and smaller...

Nicotine in Complex Samples: Recent Updates on the Pretreatment and Analysis Method

Nicotine is a significant evaluation index of tobacco and its related products' quality, but nicotine overdose can pose serious health hazards and cause addiction and dependence, thus it can be seen that it is necessary to find suitable and efficient detection methods to precisely detect nicotine in diverse samples and complex matrices. In this review, an updated summary of the latest trends in pretreatment and analytical techniques for nicotine is provided. We reviewed various sample pretreatment methods, such as solid phase extraction, solid phase microextraction, liquid phase microextraction, QuEChERS, etc., and diverse nicotine assay methods including liquid chromatography, gas chromatography, electrochemical sensors, etc., focusing on the developments since 2015. Furthermore, the recent progress in the applications and applicability of these techniques as well as our prospects for future developments are discussed.HighlightsUpdated pretreatment and analysis methods of nicotine were systematically summarized.Microextraction and automation were main development trends of nicotine pretreatment.The introduction of novel materials added luster to nicotine pretreatment.The evolutions of ion source and mass analyzer were emphasized.

ZnO Tips Dotted with Au Nanoparticles-Advanced SERS Determination of Trace Nicotine

Long-term exposure to nicotine causes a variety of human diseases, such as lung damage/adenocarcinoma, nausea and vomiting, headache, incontinence and heart failure. In this work, as a surface-enhanced Raman scattering (SERS) substrate, zinc oxide (ZnO) tips decorated with gold nanoparticles (AuNPs) are fabricated and designated as ZnO/Au. Taking advantage of the synergistic effect of a ZnO semiconductor with morphology of tips and AuNPs, the ZnO/Au-based SERS assay for nicotine demonstrates high sensitivity and the limit of detection 8.9 × 10-12 mol/L is reached, as well as the corresponding linear dynamic detection range of 10-10-10-6 mol/L. Additionally, the signal reproducibility offered by the SERS substrate could realize the reliable determination of trace nicotine in saliva.

Biocompatible MXene (Ti3C2Tx) Immobilized with Flavin Adenine Dinucleotide as an Electrochemical Transducer for Hydrogen Peroxide Detection in Ovarian Cancer Cell Lines

Flavin adenine dinucleotide (FAD) is a coenzyme and acts as a redox cofactor in metabolic process. Owing to such problems as poor electron transfer properties, unfavorable adsorption, and lack of stability on rigid electrodes, the bio-electrochemical applications of FAD have been limited. Herein, a novel fabrication method was developed for the immobilization process using 2D MXene (Ti₃C₂T_x), which enhanced the redox property of FAD and improved the electro-catalytic reduction of hydrogen peroxide (H₂O₂) in neutral medium. The FAD-immobilized Ti₃C₂T_x electrode (FAD/Ti₃C₂T_x) was studied by UV-Visible and Raman spectroscopies, which confirmed the successful adsorption of FAD on the Ti₃C₂T_x surface. The surface morphology and the elemental composition of Ti₃C₂T_x were investigated by high resolution transmission electron microscopy and the energy dispersive X-ray analysis. The redox property of the FAD/Ti₃C₂T_x modified glassy carbon electrode (FAD/Ti₃C₂T_x/GCE) was highly dependent on pH and exhibited a stable redox peak at −0.455 V in neutral medium. Higher amounts of FAD molecules were loaded onto the 2D MXene (Ti₃C₂T_x)-modified electrode, which was two times higher than the values in the reported work, and the surface coverage (ᴦ_FAD) was 0.8 × 10⁻¹⁰ mol/cm². The FAD/Ti₃C₂T_x modified sensor showed the electrocatalytic reduction of H₂O₂ at −0.47 V, which was 130 mV lower than the bare electrode. The FAD/Ti₃C₂T_x/GCE sensor showed a linear detection of H₂O₂ from 5 nM to 2 µM. The optimization of FAD deposition, amount of Ti₃C₂T_x loading, effect of pH and the interference study with common biochemicals such as glucose, lactose, dopamine (DA), potassium chloride (KCl), ascorbic acid (AA), amino acids, uric acid (UA), oxalic acid (OA), sodium chloride (NaCl) and acetaminophen (PA) have been carried out. The FAD/Ti₃C₂T_x/GCE showed high selectivity and reproducibility. Finally, the FAD/Ti₃C₂T_x modified electrode was successfully applied to detect H₂O₂ in ovarian cancer cell lines.

Representative 2D-material-based nanocomposites and their emerging applications: a review

Composites (or complex materials) are formed from two or many constituent materials with novel physical or chemical characteristics when integrated. The individual components can be combined to create a unique composite material through mechanical transfer, physical stacking, exfoliation, derivative chemical mixtures, mixtures of solid solutions, or complex synthesis processes. The development of new composites based on emerging 2D nanomaterials has allowed for outstanding achievements with novel applications that were previously unknown. These new composite materials show massive potential in emerging applications due to their exceptional properties, such as being strong, light, cheap, and highly photodegradable, and their ability to be used for water splitting and energy storage compared to traditional materials. The blend of existing polymers and 2D materials with their nanocomposites has proven to be immediate solutions to energy and food scarcity in the world. Although much literature has been reported in the said context, we tried to provide an understanding about the relationship of their mechanisms and scope for future application in a comprehensive way. In this review, we briefly summarize the basic characteristics, novel physical and chemical behaviors, and new applications in the industry of the emerging 2D-material-based composites.

Ilies) S, Orha C, Manea F. Graphene Oxide Electroreduced onto Boron-Doped Diamond and Electrodecorated with Silver (Ag/GO/BDD) Electrode for Tetracycline Detection in Aqueous Solution

A new electrochemical sensor designed by modifying the commercial boron-doped diamond (BDD) electrode with graphene oxide (GO) reduced electrochemically and further electrodecorated with silver (Ag), named the Ag/GO/BDD electrode, was selected among a series of the BDD, GOelectroreduced onto BDD (GO/BDD) and silver electrodeposited onto BDD (Ag/BDD) electrodes for the detection of tetracycline (TC) in aqueous solution. The best results regarding the sensitivity of 46.6 µA·µM-1·cm-2 and the lowest limit of detection of 5 nM was achieved using square-wave voltammetry (SWV) operated at the step potential of 5 mV, modulation amplitude of 200 mV and the frequency of 10 Hz in alkaline medium. The application of the alkaline supporting electrolyte-based procedure is limited for water monitoring due to the presence of chloride that interferes with TC detection; however, it can be applied for quantitative determination of pharmaceutical formulations. 0.1 M Na2SO4 supporting electrolyte eliminated chloride interference and can be used for the application of Ag/GO/BDD in practical detection of TC in water.

Preparation of hybrid paper electrode based on hexagonal boron nitride integrated graphene nanocomposite for free-standing flexible supercapacitors

Flexible energy storage devices have received great interest due to the increasing demand for wearable and flexible electronic devices with high-power energy sources. Herein, a novel hybrid flexible hexagonal boron nitride integrated graphene paper (BN/GrP) is fabricated from 2D hexagonal boron nitride (h-BN) nanosheets integrated with graphene sheets dispersion via a simple vacuum filtration method. FE-SEM indicated that layered graphene nanosheets tightly confined with h-BN nanosheets. Further, the Raman spectroscopy confirmed successful integration of BN with graphene. As-prepared BN/GrP free-standing flexible conductive paper showed high electrical conductivity of 5.36 × 104 S m-1 with the sheet resistance of 8.87 Ω sq-1. However, after 1000 continuous bending cycles, the BN/GrP sheet resistance increased just about 8.7% which indicated good flexibility of the paper. Furthermore, as-prepared BN/GrP showed excellent specific capacitance of 321.95 F g-1 at current density of 0.5 A g-1. In addition, the power and energy densities were obtained as 3588.3 W kg-1, and 44.7 W h kg-1, respectively. The stability of the prepared flexible electrode was tested in galvanostatic charge/discharge cycles, where the results showed the 96.3% retention even after 6000 cycles. These results exhibited that the proposed BN/GrP may be useful to prepare flexible energy-storage systems.

Assessment of Physico-Chemical and Toxicological Properties of Commercial 2D Boron Nitride Nanopowder and Nanoplatelets

Boron nitride (BN) nanomaterials have been increasingly explored for potential applications in chemistry and biology fields (e.g., biomedical, pharmaceutical, and energy industries) due to their unique physico-chemical properties. However, their safe utilization requires a profound knowledge on their potential toxicological and environmental impact. To date, BN nanoparticles have been considered to have a high biocompatibility degree, but in some cases, contradictory results on their potential toxicity have been reported. Therefore, in the present study, we assessed two commercial 2D BN samples, namely BN-nanopowder (BN-PW) and BN-nanoplatelet (BN-PL), with the objective to identify whether distinct physico-chemical features may have an influence on the biological responses of exposed cellular models. Morphological, structural, and composition analyses showed that the most remarkable difference between both commercial samples was the diameter of their disk-like shape, which was of 200-300 nm for BN-PL and 100-150 nm for BN-PW. Their potential toxicity was investigated using adenocarcinomic human alveolar basal epithelial cells (A549 cells) and the unicellular fungus Saccharomycescerevisiae, as human and environmental eukaryotic models respectively, employing in vitro assays. In both cases, cellular viability assays and reactive oxygen species (ROS) determinations where performed. The impact of the selected nanomaterials in the viability of both unicellular models was very low, with only a slight reduction of S. cerevisiae colony forming units being observed after a long exposure period (24 h) to high concentrations (800 mg/L) of both nanomaterials. Similarly, BN-PW and BN-PL showed a low capacity to induce the formation of reactive oxygen species in the studied conditions. Even at the highest concentration and exposure times, no major cytotoxicity indicators were observed in human cells and yeast. The results obtained in the present study provide novel insights into the safety of 2D BN nanomaterials, indicating no significant differences in the toxicological potential of similar commercial products with a distinct lateral size, which showed to be safe products in the concentrations and exposure conditions tested.

Recent advances in 2D hexagonal boron nitride (2D-hBN) applied as the basis of electrochemical sensing platforms

2D hexagonal boron nitride (2D-hBN) is a lesser utilised material than other 2D counterparts in electrochemistry due to initial reports of it being non-conductive. As we will demonstrate in this review, this common misconception is being challenged, and researchers are starting to utilise 2D-hBN in the field of electrochemistry, particularly as the basis of electroanalytical sensing platforms. In this critical review, we overview the use of 2D-hBN as an electroanalytical sensing platform summarising recent developments and trends and highlight future developments of this interesting, often overlooked, 2D material.