The use of electrochemical impedance spectroscopy (EIS) in the evaluation of the electrochemical properties of a microbial fuel cell

Sustainable kitchen wastewater treatment with electricity generation using upflow biofilter-microbial fuel cell system

The microbial fuel cell (MFC) is considered a modern technology used for treating wastewater and recovering electrical energy. In this study, a new dual technology combining MFC and a specialized biofilter was used. The anodic materials in the system were crushed graphite, either without coating (UFB-MFC) or coated with nanomaterials (nano-UFB-MFC). This biofilter served as a barrier to retain and remove turbidity and suspended solids, while also facilitating the role of bacteria in the removal of organic pollutants, phosphates, nitrates, sulfates, oil and greases. The results demonstrated that both systems exhibited high efficiency in treating kitchen wastewater, specifically greywater and dishwashing wastewater with high detergent concentrations. The removal efficiencies of COD, oil and grease, suspended solids, turbidity, nitrates, sulfates, and phosphates in first UFB-MFC were found to be 88, 95, 89, 86, 87, 75, and 94%, respectively, and in Nano-UFB-MFC were 86, 99, 95, 91, 81, 88, and 95%, respectively, with a high efficiency in recovering bioenergy reaching a value of 1.8 and 1.5 A m-3, respectively. The results of this study demonstrate the potential for developing MFC and utilizing it as a domestic system to mitigate pollution risks before discharging wastewater into the sewer network.

Kinetic modeling for miniaturize single-chambered microbial fuel cell: effects of biochemical reaction on its performance

In this study, Nernst growth model equations are used to explain the anodic biofilm (ABF) modeling, linear sweep voltammetry (LSV) at various growth stages of biofilm, and polarization curve modeling for its electron generation behavior in a miniaturized single-chambered microbial fuel cell (SMFC). Kinetic constants of various growth model equations were determined using non-linear regression analysis. Maximum specific growth rate (μmax) at anodic surface is observed 0.016 h-1 at a glucose concentration of 12 g L-1, whereas retardation in μmax is observed 14 g L-1 or more in SMFC. LSV results showed maximum current density of 6720.56 mA m-2. Anode performance in SMFC is examined through polarization curve resulting maximum open-circuit voltage (OCV), minimum charge transfer loss, and ohmic loss for NWG (NiWO4 impregnated on rGO), NiWO4, rGO, and plain CC (carbon cloth) anode. These results demonstrate significant enhancement in performance of MFC to lead towards model-based process controlling for significant scale-up in future.

SHOX Variations in Idiopathic Short Stature in North India and a Review of Cases from Asian Countries

Objective

Short stature homeobox (SHOX) haploinsufficiency underlies idiopathic short stature (ISS) and Leri-Weill dyschondrosteosis. The worldwide prevalence of SHOX variations in ISS varies from 2.5% to 15.0%. The aim of this study was to assess the implication of SHOX variation in ISS in North Indians and compare this with other cases of SHOX variations from Asian population.

Methods

SHOX gene analysis was carried out by multiplex ligation-dependent probe amplification followed by Sanger sequencing in 54 patients with variable phenotypes. Comparison with other reports in a meta-analysis comprising the current study and 11 previous studies (n=979) was performed.

Results

SHOX analysis resulted in 12.9% positivity (7.4% deletions and 5.5% duplications). SHOX association was seen significantly related to gender, with predominance in females (p=0.047). Short arms and forearms were the only significantly associated trait seen in 51.9% of children. The overall prevalence of SHOX variation was 15.2% in Asians with ISS. No significant difference was found in geographical region-specific analysis.

Conclusion

This study summarises findings from the last decade and provides an updated picture of the prevalence of SHOX variations in Asians, emphasizing their potential as therapeutic targets in ISS patients. Further high quality, large investigations including functional validation is warranted to validate this association.

Optimizing electrochemically active microorganisms as a key player in the bioelectrochemical system: Identification methods and pathways to large-scale implementation

The rapid global economic growth driven by industrialization and population expansion has resulted in significant issues, including reliance on fossil fuels, energy scarcity, water crises, and environmental emissions. To address these issues, bioelectrochemical systems (BES) have emerged as a dual-purpose solution, harnessing electrochemical processes and the capabilities of electrochemically active microorganisms (EAM) to simultaneously recover energy and treat wastewater. This review examines critical performance factors in BES, including inoculum selection, pretreatment methods, electrodes, and operational conditions. Further, authors explore innovative approaches to suppress methanogens and simultaneously enhance the EAM in mixed cultures. Additionally, advanced techniques for detecting EAM are discussed. The rapid detection of EAM facilitates the selection of suitable inoculum sources and optimization of enrichment strategies in BESs. This optimization is essential for facilitating the successful scaling up of BES applications, contributing substantially to the realization of clean energy and sustainable wastewater treatment. This analysis introduces a novel viewpoint by amalgamating contemporary research on the selective enrichment of EAM in mixed cultures. It encompasses identification and detection techniques, along with methodologies tailored for the selective enrichment of EAM, geared explicitly toward upscaling applications in BES.

Study on performance and mechanisms of anaerobic oxidation of methane-microbial fuel cells (AOM-MFCs) with acetate-acclimatizing or formate-acclimatizing electroactive culture

Anaerobic oxidation of methane-microbial fuel cells with acetate-acclimatizing or formate-acclimatizing electroactive culture (A-AOM-MFC and F-AOM-MFC) were designed and operated at room temperature in this study to evaluate and explore the electrochemical performance and mechanisms of methane conversion and electricity generation. The results indicated that A-AOM-MFC output a higher voltage (0.526 ± 0.001 V) and F-AOM-MFC started up in a shorter time (51 d), resulting from different mechanisms of methane-electrogen caused by discrepant microbial alliances. Specifically, in A-AOM-MFC, acetoclastic methanogens (e.g., Methanosaeta) converted methane into intermediates (e.g., acetate) through reversing methanogenesis and carried out the direct interspecific electron transfer (DIET) with Geobacter-predominated electricigens which can oxidize the intermediates to carbon dioxide and transfer electrons to the electrodes. Differently, the intermediate-dependent extracellular electron transfer (EET) existed in F-AOM-MFC between hydro-methanogens (e.g., Methanobacterium) and electricigens (e.g., Geothrix), which was more difficult than DIET. Additionally, hydro-methanogens metabolized methane to produce formate-dominant intermediates more quickly.

Adaptation of anammox consortia in microbial fuel cell to low temperature: Microbial community and predictive functional profiling

The purpose of this study was to explore the tolerance mechanism of anammox consortia in microbial fuel cell (MFC) system at low temperature. Data showed that nearly 80 % total nitrogen removal was achieved after the temperature decreased from 30 °C to 15 °C. The nitrogenremovalrate (NRR) of the system was decreased by 26.3 %, from 0.441 kgN·m^-3·d^-1 at 30 °C to 0.325 kgN·m^-3·d^-1 at 15 °C. Isotope experiment in ¹⁵NH₄⁺-containing reactor found that much more ²⁹N₂ were produced than ³⁰N₂, confirming that anammox was the main ¹⁵NH₄⁺ removal pathway and electrochemical oxidation participate in this process. High throughput sequencing analysis indicated the low temperature stimulated the enrichment of heterotrophic bacteria, such as Comamonadaceae and Rhodobacteraceae. While the relative abundance of Candidatus Brocadia, typical anammox bacteria, decreased significantly. Kyoto Encyclopaedia of Genes and Genomes (KEGG) pathway analysis showed that the low temperature induced a more efficient expression in synthesis of unsaturated fatty acids (UFAs) and ABC membrane transports. This study indicates that anammox consortia are likely to maintain high nitrogen removal performance of MFC system by changing the proportion of membrane composition and EPS exportation.

Simultaneous Anaerobic Ammonium Oxidation and Electricity Generation in Microbial Fuel Cell: Performance and Electrochemical Characteristics

In this study, a microbial fuel cell (MFC) that can achieve simultaneous anode anaerobic ammonium oxidation (anammox) and electricity generation (anode anammox MFC) by high-effective anammox bacteria fed with purely inorganic nitrogen media was constructed. As the influent concentrations of ammonium (NH4+-N) and nitrite (NO2−-N) gradually increased from 25 to 250 mg/L and 33–330 mg/L, the removal efficiencies of NH4+-N, NO2−-N and TN were over 90%, 90% and 80%, respectively, and the maximum volumetric nitrogen removal rate reached 3.01 ± 0.27 kgN/(m3·d). The maximum voltage and maximum power density were 225.48 ± 10.71 mV and 1308.23 ± 40.38 mW/m3, respectively. Substrate inhibition took place at high nitrogen concentrations (NH4+-N = 300 mg/L, NO2−-N = 396 mg/L). Electricity production performance significantly depended upon the nitrogen removal rate under different nitrogen concentrations. The reported low coulombic efficiency (CE, 4.09–5.99%) may be due to severe anodic polarization. The anode charge transfer resistance accounted for about 90% of the anode resistance. The anode process was the bottleneck for energy recovery and should be further optimized in anode anammox MFCs. The high nitrogen removal efficiency with certain electricity recovery potential in the MFCs suggested that anode anammox MFCs may be used in energy sustainable nitrogen-containing wastewater treatment.

Electrochemical impedance spectroscopy applied to microbial fuel cells: A review

Electrochemical impedance spectroscopy (EIS) is an efficient and non-destructive test for analyzing the bioelectrochemical processes of microbial fuel cells (MFCs). The key factors limiting the output performance of an MFC can be identified by quantifying the contribution of its various internal parts to the total impedance. However, little attention has been paid to the measurement conditions and diagrammatic processes of the EIS for MFC. This review, starting with the analysis of admittance of bioelectrode, introduces conditions for the EIS measurement and summarizes the representative equivalent circuit plots for MFC. Despite the impedance from electron transfer and diffusion process, the effect of unnoticeable capacitance obtained from the Nyquist plot on MFCs performance is evaluated. Furthermore, given that distribution of relaxation times (DRT) is an emerging method for deconvoluting EIS data in the field of fuel cell, the application of DRT-analysis to MFC is reviewed here to get insight into bioelectrode reactions and monitor the biofilm formation. Generally, EIS measurement is expected to optimize the construction and compositions of MFCs to overcome the low power generation.

New Microfluidic System for Electrochemical Impedance Spectroscopy Assessment of Cell Culture Performance: Design and Development of New Electrode Material

Electrochemical impedance spectroscopy (EIS) is widely accepted as an effective and non-destructive method to assess cell health during cell-culture. However, there is a lack of compact devices compatible with microfluidic integration and microscopy that could provide the real-time and non-invasive monitoring of cell-cultures using EIS. In this paper, we reported the design and characterization of a modular EIS testing system based on a patented technology. This device was fabricated using easily processable methodologies including screen-printing of the impedance electrodes and molding or micromachining of the cell culture chamber with an easy assembly procedure. Accordingly, to obtain processable, biocompatible and sterilizable electrode materials that lower the impact of interfacial impedance on TEER (Transepithelial electrical resistance) measurements, and to enable concomitant microscopy observations, we optimized the formulation of the electrode inks and the design of the EIS electrodes, respectively. First, electrode materials were based on carbon biocompatible inks enriched with IrOx particles to obtain low interfacial impedance electrodes approaching the performances of classical non-biocompatible Ag/AgCl second-species electrodes. Secondly, we proposed three original electrode designs, which were compared to classical disk electrodes that were optically compatible with microscopy. We assessed the impact of the electrode design on the response of the impedance sensor using COMSOL Multiphysics. Finally, the performance of the impedance spectroscopy devices was assessed in vitro using human airway epithelial cell cultures.

Introducing Alternative Algorithms for the Determination of the Distribution of Relaxation Times

Impedance spectroscopy is a powerful characterization method to evaluate the performance of electrochemical systems. However, overlapping signals in the resulting impedance spectra oftentimes cause misinterpretation of the data. The distribution of relaxation times (DRT) method overcomes this problem by transferring the impedance data from the frequency domain into the time domain, which yields DRT spectra with an increased resolution. Unfortunately, the determination of the DRT is an ill‐posed problem, and appropriate mathematical regularizations become inevitable to find suitable solutions. The Tikhonov algorithm is a widespread method for computing DRT data, but it leads to unlikely spectra due to necessary boundaries. Therefore, we introduce the application of three alternative algorithms (Gold, Richardson Lucy, Sparse Spike) for the determination of stable DRT solutions and compare their performances. As the promising Sparse Spike deconvolution has a limited scope when using one single regularization parameter, we furthermore replaced the scalar regularization parameter with a vector. The resulting method is able to calculate well‐resolved DRT spectra.

Comparative Study of Different Production Methods of Activated Carbon Cathodic Electrodes in Single Chamber MFC Treating Municipal Landfill Leachate

The treatment of real waste extracts with simultaneous energy production is currently under research. One method of addressing this dual task is using biochemical reactors named microbial fuel cells (MFCs). MFCs consist of a bioanode and a cathode where the oxygen reduction reaction (ORR) occurs. Cathodes are currently under optimization regarding the nature of their support, their catalytic efficiency and their configurations. In this work, we present facile preparation methods for the production of activated carbon ceramic-supported cathodic electrodes produced with three different techniques (wash-coat, brush-coat, and ultrasound-assisted deposition/infiltration). The produced cathodic electrodes were tested in a single-chamber MFC, filled with the concentrated liquid residue, after the reverse osmosis (RO-CLR) treatment of leachate from a municipal waste landfill, in order to exploit their electrochemical potential for simultaneous waste treatment and energy production. The electrode produced utilizing 20 kHz ultrasounds proved to be more effective in terms of energy harvesting (10.7 mW/g·L of leachate) and wastewater treatment (COD removal 85%). Internal resistances of the ultrasound-produced electrodes are lower, as compared to the other two methods, opening new exploitation pathways in the use of ultrasound as a means in producing electrodes for microbial fuel cells.

Combined phyto-microbial-electrochemical system enhanced the removal of petroleum hydrocarbons from soil: A profundity remediation strategy

The soil contaminated by petroleum hydrocarbons has been a global environmental problem and its remediation is urgent. A combined phyto-microbial-electrochemical system (PMES) was constructed to repair the oil-contaminated soil in this study. During the 42-day operation time, a total petroleum hydrocarbons (TPHs) of 18.0 ± 3.0% were removed from PMES, which increased by 414% compared with the control group (CK1). The supervision of physicochemical properties of pore water in soil exhibited an enhanced microbial consumption of the total organic carbon (TOC) and N source under the applied potential with the generation of bio-current. The microbial succession indicated that the Dietzia, Georgenia and Malbranchea possibly participated in the degradation and current output in PMES. And a collaborative network of potential degrading microorganisms including unclassified norank_f__JG30-KF-CM45 (in Chloroflexi), Dietzia and Malbranchea was discovered in PMES. While the functional communities of microorganism were re-enriched with the reconstructed interactions in the system which was started with the sterilized soil (S+MEC). The superiority of TPHs degradation in S+MEC compared to P + CK2 (removing the electrochemical effect relative to CK1) revealed the key role of external potential in regulating the degradation microflora. The study provided a strategy of the potential regulated phyto-microbial interaction for the removal of TPHs.

Molecularly imprinted photoelectrochemical sensor for detecting tetrabromobisphenol A in indoor dust and water

The gradual emissions of tetrabromobisphenol A (TBBPA) from the primitive recycling of E-waste create human health threats, which urgently require to develop an efficient, rapid yet simple detection method. The present study conducts a highly sensitive molecularly imprinted photoelectrochemical sensor (MIPES) containing molecularly imprinted (MI)-TiO₂, Au, and reduced graphene oxide for the trace detection of TBBPA in indoor dust and surface water from an E-waste recycling area. The photocurrent response is used to evaluate the sensing performance of the MIPES toward TBBPA detection. The working potential for amperometry is 0.48 V. The wavelength range for photoelectrochemical detection is 320-780 nm. The sensor shows a detection range of 1.68 to 100 nM with a low limit of detection of 0.51 nM (LOD = 3 s_b/S) and a limit of quantification of 1.68 nM (LOQ = 3.3 LOD). In addition, the MIPES sensor exhibits rapid, excellent reproducibility, selectivity, and long-term stability toward TBBPA detection. The relative standard deviation of three measurements for real samples is less than 7.0%, and the recovery range is 90.0-115%. The surface of molecular imprinting contributes to the high charge separation and sensing photocurrent response of TBBPA, which is confirmed by single-particle photoluminescence spectroscopy. The present study provides a new facile sensor with highly sensitive yet rapid response to detect environmental pollutants in E-waste by using the MIPES.

A review of the operating parameters on the microbial fuel cell for wastewater treatment and electricity generation

Environmental and economic considerations suggest a more efficient and comprehensive use of biomass for bioenergy production. One of the most attractive technologies is the microbial fuel cell using the catabolic activity of microorganisms to generate electricity from organic matter. The microbial fuel cell (MFC) has operational benefits and higher performance than current technologies for producing energy from organic materials because it converts electricity from the substrate directly (at ambient temperature). However, MFCs are still not suitable for high energy demand due to practical limitations. The overall performance of an MFC depends on the electrode material, the reactor design, the operating parameters, substrates, and microorganisms. Furthermore, the optimization of the parameters will lead to the commercial development of this technology in the near future. The simultaneous effect of the parameters on each other (intensifier or attenuator) has also been investigated. The investigated parameters in this study include temperature, pH, flow rate and hydraulic retention time, mode, external resistance, and initial concentration.

Microbiologically Influenced Corrosion Behavior of Carbon Steel in the Presence of Marine Bacteria Pseudomonas sp. and Vibrio sp

The microbiologically influenced corrosion (MIC) behavior of carbon steel is investigated in the presence of Vibrio and Pseudomonas. Sterilized natural seawater inoculated with Pseudomonas, Vibrio, and the mixture of Pseudomonas and Vibrio, separately, and they are utilized as the media for corrosion characterizations, which are closer to the natural environment in seawater. Weight loss measurements, electrochemical techniques (the open-circuit potential, electrochemical impedance spectroscopy (EIS), and potentiodynamic polarization curves), and surface analysis (scanning electron microscopy (SEM)) are performed to explore the synergistic effect of Pseudomonas and Vibrio on the corrosion behavior of carbon steel. As seen from the growth curves of bacteria, the growth and propagation of Pseudomonas and Vibrio are affected by their metabolic activities. Besides, the results obtained by SEM show that more severe pitting corrosion is observed on the coupons exposed to the sterilized natural seawater inoculated with the mixture of Pseudomonas and Vibrio. Further, the results from electrochemical measurements and weight loss measurements suggest that under the synergistic effect of Pseudomonas and Vibrio, the initial corrosion rate of carbon steel is inhibited, while the latter corrosion is enhanced.

The influential role of external electrical load in microbial fuel cells and related improvement strategies: A review

The scope of the currentreviewis to discuss and evaluate the role of the external electrical load/resistor (EEL) on the overall behavior and functional properties of microbial fuel cells (MFCs). In this work, a comprehensive analysis is made by considering various levels of MFC architecture, such as electric and energy harvesting efficiency, anode electrode potential shifts, electro-active biofilm formation, cell metabolism and extracellular electron transfer mechanisms, as a function of the EEL and its control strategies. It is outlined that taking the regulation of EEL into account at MFC optimization is highly beneficial, and in order to support this step, in this review, a variety of guidelines are collected and analyzed.

Stimuli-Responsive Templated Polymer as a Target Receptor for a Conformation-based Electrochemical Sensing Platform

The use of highly crosslinked molecularly imprinted polymers as a synthetic target receptor has the limitations of restricted accessibility to the binding sites resulting in slow response time. Moreover, such artificial receptors often require additional transduction mechanisms to translate target binding events into measurable signals. Here, we propose the development of a single-chain stimuli-responsive templated polymer, without using any covalent interchain crosslinkers, as a target recognition element. The synthesized polymer chain exhibits preferential binding with the target molecule with which the polymer is templated. Moreover, upon specific target recognition, the polymer undergoes conformation change induced by its particular stimuli responsiveness, namely the target binding event. Such templated single-chain polymers can be attached to the electrode surface to implement a label-free electrochemical sensing platform. A target analyte, 4-nitrophenol (4-NP), was used as a template to synthesize a poly-N-isopropylacrylamide (PNIPAM)-based copolymer chain which was anchored to the electrode to be used as a selective receptor for 4-NP. The electrode surface chemistry analysis and the electrochemical impedance study reveal that the polymer concentration, the interchain interactions, and the Hofmeister effect play a major role in influencing the rate of polymer grafting as well as the morphology of the polymers grafted to the electrode. We also show that the specific binding between 4-NP and the copolymer results in a substantial change in the charge transfer kinetics at the electrode signifying the polymer conformation change.

Good microbial affinity of phenolic carbon felt as an efficient anode for microbial fuel cells

Phenolic carbon felt (PCF) is a three-dimensional material with a simple manufacturing process and low cost. To investigate the application of PCF as an anode material for use in microbial fuel cells (MFCs), we employed PCF as the anode material for the first time in MFCs that were carbonized at different temperatures. The relationship between the intrinsic characteristics and the electrochemical performance of different PCFs was also analyzed. Here, we obtained the best power generation with a power density of up to 2600 mW/m² when PCF was heated to 900 °C (PCF-900); this power generation was much higher than that of the commercial carbon felts. From SEM images, we found that the biofilm growth of PCF-900 was quite uniform. This may result from the higher surface electropositivity of PCF-900 and increased electrostatic attraction between the microorganisms and PCF. We also analyzed the conductivity, specific surface area, functional groups, and surface charge of the PCF anode. Under the synergistic effect of these intrinsic properties, PCF-900 showed good biocompatibility for the adhesion of microorganisms and high electron transfer efficiency. In addition, PCF was easily prepared in different sizes. Thus, it could be a promising material for the application of scale-up MFCs.

Towards the practical application of bioelectrochemical anaerobic digestion (BEAD): Insights into electrode materials, reactor configurations, and process designs

Anaerobic digestion (AD) is one of the most widely adopted bioenergy recovery technologies globally. Despite the wide adoption, AD has been challenged by the unstable performances caused by imbalanced substrate and/or electron availability among different reaction steps. Bioelectrochemical anaerobic digestion (BEAD) is a promising concept that has demonstrated potential for balancing the electron transfer rates and enhancing the methane yield in AD during shocks. While great progress has been made, a wide range of, and sometimes inconsistent engineering and technical strategies were attempted to improve BEAD. To consolidate past efforts and guide future development, a comprehensive review of the fundamental bioprocesses in BEAD is provided herein, followed by a critical evaluation of the engineering and technical optimizations attempted thus far. Further, a few novel directions and strategies that can enhance the performance and practicality of BEAD are proposed for future research to consider. This review and outlook aim to provide a fundamental understanding of BEAD and inspire new research ideas in AD and BEAD in a mechanism-informed fashion.

Photo-electrochemical detection of dopamine in human urine and calf serum based on MIL-101 (Cr)/carbon black

A new photo-electrochemical sensor based on MIL-101(Cr) MOF/carbon black (CB) is fabricated and characterized. By using differential pulse voltammetry, dopamine (DA) can be effectively detected using a photo-electrochemical MIL-101(Cr)/CB sensor under visible light. The CB acts as the electron bridge to combine with the large specific surface area and photo-catalytic feature of MOF, which contribute to the improvements of sensitivity of DA detection. The concentration of the catalyst, pH value, accumulation potential, and accumulation time were also optimized. Furthermore, the electrochemical performances of MIL-101(Cr)/CB sensor was investigated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), scan rate, electrochemically active surface area (ECSA), and amperometric responses. A detection limit of 0.38 nM (LOD = 3 s_b/S, s_b = 0.028) and a working range of 1 nM to 2.22 μM has been achieved. The MIL-101(Cr)/CB sensor exhibits excellent reproducibility, stability, and selectivity and also has satisfactory recovery rate for the analysis of real samples including calf serum and human urine. Graphical abstract.

A Novel Method to Reveal a Ureolytic Biofilm Attachment and In Situ Growth Monitoring by Electrochemical Impedance Spectroscopy

The formation of biofilms capable of efficiently carrying out ureolysis is of fundamental importance in several biotechnological systems such as urinary tract infections, building materials and municipal wastewater treatment. This work proposes a straightforward method for the formation of a ureolytic biofilm attached to graphite. The proposed strategy reduced the time needed to complete ureolysis to 3 days instead of 16 days required in suspension culture. To confirm the formation of a ureolytic biofilm, scanning electron microscopy and confocal laser scanning microscopy studies were employed ex situ. However, it is imperative to analyse the biofilm by direct non-invasive techniques. Accordingly, open circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) were used as in situ monitoring techniques. The reduction in OCP from - 0.01 to - 0.2 V vs. Ag/AgCl and the increase in capacitance from 200 to 260 μF cm^-2 were related to biofilm attachment. To the best of our knowledge, this is the first time in which a ureolytic biofilm attachment has been analysed by EIS. The increase in the biomass from 0.04 to 2.81 μm³ μm^-2 and in average thickness from 10.19 to 32.78 μm was related to biofilm maturation.

Electrogenic Biofilm Development Determines Charge Accumulation and Resistance to pH Perturbation

The electrogenic biofilm and the bio-electrode interface are the key biocatalytic components in bioelectrochemical systems (BES) and can have a large impact on cell performance. This study used four different anodic carbons to investigate electrogenic biofilm development to determine the influence of charge accumulation and biofilm growth on system performance and how biofilm structure may mitigate against pH perturbations. Power production was highest (1.40 W/m3) using carbon felt, but significant power was also produced when felt carbon was open-circuit acclimated in a control reactor (0.95 W/m3). The influence of carbon material on electrogenic biofilm development was determined by measuring the level of biofilm growth, using sequencing to identify the microbial populations and confocal microscopy to understand the spatial locations of key microbial groups. Geobacter spp. were found to be enriched in closed-circuit operation and these were in close association with the carbon anode, but these were not observed in the open-circuit controls. Electrochemical analysis also demonstrated that the highest mid-point anode potentials were close to values reported for cytochromes from Geobacter sulfurreductans. Biofilm development was greatest in felt anodes (closed-circuit acclimated 1209 ng/μL DNA), and this facilitated the highest pseudo-capacitive values due to the presence of redox-active species, and this was associated with higher levels of power production and also served to mitigate against the effects of low-pH operation. Supporting carbon anode structures are key to electrogenic biofilm development and associated system performance and are also capable of protecting electrochemically active bacteria from the effects of environmental perturbations.

Bifunctional cathode using a biofilm and Pt/C catalyst for simultaneous electricity generation and nitrification in microbial fuel cells

Biofouling frequently causes catalyst deterioration at the cathode of microbial fuel cells (MFCs). A biofilm-covered Pt/C cathode (BPC) was fabricated via in situ cultivation of a biofilm on a Pt/C cathode (PC) in a dual-chambered MFC, which enables effective removal of NH4+-N and copious generation of electricity. Experimental results show 99% NH4+-N removal by the nitrifying bacteria that constitute 35.7% of all microorganisms on the BPC and a maximum BPC-MFC power density of 0.97 W/m2, which is comparable to that of PC-MFCs (0.99 W/m2). BPC biofilm size is restricted by the limited amount of organic material in the cathode chamber, which constrains the biomass to less than 0.3 g protein /m2. The bifunctional-cathode equipped MFC shows great promise as an energy-saving technology for wastewater treatment in the future.

Corrosion Resistance of Multilayer Coatings Deposited by PVD on Inconel 718 Using Electrochemical Impedance Spectroscopy Technique

AlCrN/TiSi, AlCrN/TiCrSiN and AlCrN/AlCrN + CrN coatings were deposited on Inconel 718 alloy by physical vapour deposition (PVD). The corrosion behaviour of uncoated and coated specimens was evaluated using electrochemical impedance spectroscopy (EIS) at open circuit potential in a 3.5 wt.% NaCl and 2 wt.% H2SO4 solutions. The EIS data acquired were curve fitted and analysed by equivalent circuit models to calculate the pore resistance, the charge transfer resistance and the capacitance. The Nyquist diagrams of all systems showed one part of the semicircle which could relate that reaction is a one step process, except for the AlCrN/TiCrSiN and AlCrN/AlCrN + CrN coatings in H2SO4 solution, for which two semicircles related to active corrosion in substrate alloy were found. However, from the Bode plots, it was possible to identify two the time constants for all systems exposed to NaCl and H2SO4 solutions. According to electrochemical results, the corrosion resistance of the AlCrN/TiSiN coating was better in the NaCl solution, whereas the AlCrN/AlCrN + CrN coating show better performance in the Sulphuric Acid solutions.

Scratching and transplanting of electro-active biofilm in fruit peeling leachate by ultrasound: re-inoculation in new microbial fuel cell for enhancement of bio-energy production and organic matter detection

OBJECTIVE

An electro-active biofilm of Fruit Peeling (FP) leachate was formed onto the Carbon Felt (CF) bio-anode in a Microbial Fuel Cell (MFC), after functioning for a long time. The electro active-biofilm thus formed was then scratched by ultrasound and re-inoculated in a new leachate to be transplanted onto the bio-anode. This procedure allowed the microbial electron charge transfer and therefore the enhancement of the bio-energy production of the fuel cell.

RESULTS

By using the repetitive mechanical biofilm removal, re-suspension and electrochemically facilitated biofilm formation, the voltage was substantially increased. In effect, the voltage of the 1st G of biofilm, rose gradually and reached its maximum value of 65 mV after 10 days. Whilst the 2nd generation allowed to obtain the maximum voltage 276 mV and without any lag time. The DCO abatement using the 1st G biofilm was 68% greater than the 3rd G 26%. Besides, the electrochemical impedance spectroscopy characterization and cyclic voltammetry of bio-anode with 2nd G biofilm confirmed the ability of electro-active biofilm formation on a new support. The biofilm transplanted showed thus greater kinetic performance, with reduced lag time demonstrating the interest of the selection that took place during the formation of successive biofilms.

CONCLUSIONS

Despite the transplantation of the electro-active biofilm onto the bio-anode, the MFC still produced relatively lower power output. Nevertheless, it has been tested successfully for monitoring and detecting the oxidation of sodium acetate substrate in the very wide concentration range 0.0025-35 g/l.

Boosting Specific Energy and Power of Carbon-Ionic Liquid Supercapacitors by Engineering Carbon Pore Structures

Carbon-ionic liquid (C-IL) supercapacitors (SCs) promise to provide high capacitance and high operating voltage, and thus high specific energy. It is still highly demanding to enhance the capacitance in order to achieve high power and energy density. We synthesized a high-pore-volume and specific-surface-area activated carbon material with a slit mesoporous structure by two-step processes of carbonization and the activation from polypyrrole. The novel slit-pore-structured carbon materials provide a specific capacity of 310 F g⁻¹ at 0.5 A g⁻¹ for C-IL SCs, which is among one of the highest recorded specific capacitances. The slit mesoporous activated carbons have a maximum ion volume utilization of 74%, which effectively enhances ion storage, and a better interaction with ions in ionic liquid electrolyte, thus providing superior capacitance. We believe that this work provides a new strategy of engineering pore structure to enhance specific capacitance and rate performance of C-IL SCs.

Microbiologically influenced corrosion mechanism of 304L stainless steel in treated urban wastewater and protective effect of silane-TiO2 coating

Microbiologically influenced corrosion (MIC) of bare and silane-TiO₂ sol-gel coated stainless steel (SS) was studied in treated urban wastewater (TUWW). Combining the electrochemical impedance spectroscopy (EIS) and the scanning vibrating electrode technique (SVET) showed that SS surface colonization occurs, at earlier stages, by iron-oxidizing bacteria (IOB), and later by sulphate-reducing bacteria (SRB). The SVET results showed that chemical corrosion process and bacterial respiration led to the depletion of dissolved oxygen, creating a differential aeration cell and thus a localized corrosion phenomenon. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) showed that the growth of a bacterial biofilm on 304L SS was a dynamic process, stimulating the localized oxidation of SS. To improve corrosion protection, a silane-TiO₂ sol-gel coating for SS is proposed. SEM showed that the coating reduced bacterial adhesion and EIS study demonstrated that the coating improved the barrier properties and corrosion resistance of 304L SS in TUWW over a short period of immersion.

Microbial electrochemical technologies: Electronic circuitry and characterization tools

Microbial electrochemistry merges microbiology, electrochemistry and electronics to provide a set of technologies for environmental engineering applications. Understanding the electronic concepts is crucial for effectively adopting these systems, but the importance of electronic circuitry is often overlooked by microbial electrochemistry researchers. This review provides the background on the electronics and electrochemical concepts involved in the study of microorganisms interacting with electricity, and their applications in microbial electrochemical technology (MET). The potentiostat circuitry is described along with its working principles. Electrochemical analyses are presented together with the rational and parameters employed to study MET devices and electroactive microorganisms. Finally, future directions are delineated towards the adoption of MET, and the related electronics, in environmental engineering applications.

Effect of anaerobic sludge on the bioelectricity generation enhancement of bufferless single-chamber microbial fuel cells

Enhancing the self-buffering capacity is critical in the operation of bufferless microbial fuel cells (BLMFCs). Inorganic carbon (IC) is an ideal endogenous buffer, but its spontaneously accumulated concentration is insufficient to adjust anolyte pH. In this study, BLMFCs were operated with anaerobic sludge to enhance IC accumulation and increase anolyte pH. The accumulated IC concentration during a single running cycle was elevated from 8.3 mM to 12.5 mM, and anolyte pH remained above 7.5. The electric power output was significantly promoted from 332.2 mW·m^-2 to 628.1 mW·m^-2, and the coulombic efficiency (CE) slightly increased from 16.4% to 19.5%. Geobacter was the electro-active genus in the anode biofilms of the MFCs, and its relative abundance in the KCl-S anode biofilm increased from 0.2% to 5.75%. After continuous operation, the predominant genus of the anaerobic sludge had changed from Flavobacterium to Fusibacter.

Influence of the major pilA transcriptional regulator in electrochemical responses of Geobacter sulfureducens PilR-deficient mutant biofilm formed on FTO electrodes

Geobacter sulfurreducens is a model organism for understanding the role of bacterial structures in extracellular electron transfer mechanism (EET). This kind of bacteria relies on different structures such as type IV pili and over 100 c-type cytochromes to perform EET towards soluble and insoluble electron acceptors, including electrodes. To our knowledge, this work is the first electrochemical study comparing a G. sulfurreducens PilR-deficient mutant and wild type biofilms developed on fluorine-doped tin oxide (FTO) electrodes. Open circuit potential (OCP), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV), were used to evaluate the electroactive properties of biofilms grown without externally imposed potential. Parallel studies of Confocal Laser Scanning Microscopy (CLSM) correlated with the electrochemical results. PilR is a transcriptional regulator involved in the expression of a wide variety of genes, including pilA (pilus structural protein) relevant c-type cytochromes and some other genes involved in biofilm formation and EET processes. Our findings suggest that PilR-deficient mutant forms a thinner (CLSM analysis) and less conductive biofilm (EIS analysis) than wild type, exhibiting different and irreversible redox processes at the interface (CV analysis). Additionally, this work reinforces some of the remarkable features described in previous reports about this G. sulfurreducens mutant.

Composition and distribution of internal resistance in an enzymatic fuel cell and its dependence on cell design and operating conditions

A variety of sugar-based enzymatic fuel cells (EFCs) are able to completely oxidize fuels catalyzed by enzyme cascades, achieving high energy densities. However, the poor power output of EFCs limits their potential applications. In the present study, the composition of internal resistance throughout the EFCs affected by various factors, including the separator, enzyme loading, electron acceptor, applied voltage and operation time, was characterized by electrochemical impedance spectroscopy (EIS). Total resistance is divided into solution-separator resistance, charge transfer resistance, and diffusion resistance, respectively. The Nafion 212 membrane was found to yield a small solution-separator resistance and a high power density. Increased enzyme loading led to reduced internal resistance and improved cell performance, generating a maximum power density of 0.17 mW cm⁻². Using potassium ferricyanide to replace oxygen as the electron acceptor could improve cathode performance significantly and resulted in a 4-fold increase in the power density. EIS was also performed for EFCs operated continuously for 16 h. Power output decreased distinctly over time, while the internal resistance, primarily the diffusion resistance, increased. Additionally, altering operation voltages had an impact on diffusion resistances. These results can be summarized that diffusion plays a rather important role in deciding the power and future efforts should be made towards increasing the mass transfer in EFCs.

This work systematically investigated the impact of operating conditions on the internal resistance of a sugar-based EFC.

Tungsten oxide as electrocatalyst for improved power generation and wastewater treatment in microbial fuel cell

Microbial fuel cell (MFC) is a device that oxidizes the organic matter present in wastewater and simultaneously generates electricity from it. For practical applications, the power production of MFCs needs to be enhanced and the use of novel anode and cathode catalyst can certainly help in this regard. Such a novel catalyst, WO₃, was explored as both anode and cathode catalyst in this study. Performance of MFCs was enhanced when WO₃ was used as an electrocatalyst. The maximum power density of MFC was increased by five times when WO₃ was used as anode catalyst and by four times when it was used as cathode catalyst as compared to control MFC using electrode without any catalyst. Almost six times increment in maximum power production of MFC was observed when WO₃ was used as catalyst on both the electrodes. Electrochemical analysis of WO₃ also proved that it could enhance the current density of the modified electrode owing to its electrochemical catalytic properties. Furthermore, chemical oxygen demand (COD) removal of MFC having WO₃ coated electrodes was also observed to be higher, thus suggesting an overall enhancement in the performance of MFC by the use of WO₃ as an electrocatalyst.

Engineering rheology of electrolytes using agar for improving the performance of bioelectrochemical systems

The present study is focused on enhancing the rheological properties of the electrolyte and eliminating sedimentation of microorganisms/flocs without affecting the electron transfer kinetics for improved bioelectricity generation. Agar derived from polysaccharide agarose (0.05-0.2%, w/v) was chosen as a rheology modifying agent. Electroanalytical investigations showed that electrolytes modified with 0.15% agar display a nine-fold increase in current density (1.2 mA/cm²) by a thermophilic strain (Geobacillus sp. 44C, 60 °C) when compared with the control. Sodium phosphate buffer (0.1 M, pH 7) electrolyte with riboflavin (0.1 mM) was used as the control. Electrolytes modified with 0.15% agar significantly improved chemical oxygen demand removal rates. This developed electrolyte will aid in improving bioelectricity generation in Bioelectrochemical Systems (BES). The developed strategy avoids the use of peristaltic pumps and magnetic stirrers, thereby improving the energy efficiency of the process.

Environmentally available biowastes as substrate in microbial fuel cell for efficient chromium reduction

Dual chambered microbial fuel cells with Potassium dichromate (22 g/L, MFC-1) and tannery effluent waste water containing 26 mg/L (MFC-2), 5 mg/L (MFC-3) of Cr(VI) as catholyte, sweet lime waste inoculated by cowdung as anolyte and graphite electrodes were used to reduce toxic Cr(VI) to Cr(III) with simultaneous power generation. Cr (VI) in the cathode chamber reduced to Cr₂O₃ within 24 h. Complete reduction of Cr(VI) from tannery effluents by microbial fuel cell is noticed within 10 days. The 16 s rRNA sequencing studies demonstrated presence of Geobacter Metallireducens in mixed culture bacteria in anaerobic anode. The power density of the device is 396.7 mW/m²on day1which is 7.2 times higher than literature data of 55.5 mW/m². The processes involved on the biofilm/electrolyte interface and graphite/electrolyte interface is studied by Electrochemical Impedance Spectroscopy. Electrochemical studies demonstrated the active growth of biofilm on anode which reduces charge transfer resistance from day 1 to day 25. The concentration of Cr(VI) reduced in the present studies are approximately 1000 times higher than those reported in the literature.

Electro-Microbiology as a Promising Approach Towards Renewable Energy and Environmental Sustainability

Microbial electrochemical technologies provide sustainable wastewater treatment and energy production. Despite significant improvements in the power output of microbial fuel cells (MFCs), this technology is still far from practical applications. Extracting electrical energy and harvesting valuable products by electroactive bacteria (EAB) in bioelectrochemical systems (BESs) has emerged as an innovative approach to address energy and environmental challenges. Thus, maximizing power output and resource recovery is highly desirable for sustainable systems. Insights into the electrode-microbe interactions may help to optimize the performance of BESs for envisioned applications, and further validation by bioelectrochemical techniques is a prerequisite to completely understand the electro-microbiology. This review summarizes various extracellular electron transfer mechanisms involved in BESs. The significant role of characterization techniques in the advancement of the electro-microbiology field is discussed. Finally, diverse applications of BESs, such as resource recovery, and contributions to the pursuit of a more sustainable society are also highlighted.

Rewiring the microbe-electrode interfaces with biologically reduced graphene oxide for improved bioelectrocatalysis

The aim of this work was to study biologically reduced graphene oxide (RGO) for engineering the surface architecture of the bioelectrodes to improve the performance of Bioelectrochemical System (BES). Gluconobacter roseus mediates the reduction of graphene oxide (GO). The RGO modified bioelectrodes produced a current density of 1 mA/cm² and 0.69 mA/cm² with ethanol and glucose as substrates, respectively. The current density of RGO modified electrodes was nearly 10-times higher than the controls. This study, for the first time, reports a new strategy to improve the yield as well as efficiency of the BES by wrapping and wiring the electroactive microorganisms to the electrode surfaces using RGO. This innovative wrapping approach will decrease the loss of electrons in the microbe-electrolyte interfaces as well as increase the electron transfer rates at the microorganism-electrode interfaces.

The catalytic effect of TiO2 nanosheets on extracellular electron transfer of Shewanella loihica PV-4

Electron transfer kinetics of Shewanella loihica PV-4 at the up-growing TiO₂ nanosheet (TiO₂-NS) modified carbon paper (CP) electrode was investigated. The effect of TiO₂-NSs, which speeds up the interfacial electron transfer of outer membrane c-type cytochromes (OMCs), was revealed for the first time. TiO₂-NSs with a polar surface modified hydrophobic CP into super-hydrophilic TiO₂-NS/CP. The favorable interaction between PV-4 and TiO₂-NSs not only enhanced microbial adhesion, but also altered the redox nature of OMCs. The mid-point potential of OMCs at TiO₂-NS/CP was shifted to a more negative potential, indicating a higher thermodynamic driving force for the protein to release electrons. Moreover, electron transfer from OMCs to TiO₂-NSs was also benefited from the positive shift of flat-band potential V_fb owing to reduced pH at the electrode/microorganism interface, as well as good electrical conductivity of TiO₂-NSs. As a result, the electron transfer rate constant k_et of OMCs at the TiO₂-NS/CP anode was about three times faster than that at the CP anode. The accelerated electron transfer kinetics as well as 15% increase of biomass together accounted for a 97% increase of the maximum output power density in the MFC. The result expanded our knowledge about the role of a designed TiO₂ nanostructure in microbial electron transfer that can be applied in other bio-electrochemical systems.