A study of microbial communities on terracotta separator and on biocathode of air breathing microbial fuel cells

Enhanced thermophilic high-solids anaerobic digestion of organic fraction of municipal solid waste with spatial separation from conductive materials in a single reactor volume

Despite benefits such as lower water and working volume requirements, thermophilic high solids anaerobic digestion (THSAD) often fails due to the rapid build-up of volatile fatty acids (VFAs) and the associated drop in pH. Use of conductive materials (CM) can promote THSAD through stimulation of direct interspecies electron transfer (DIET), while the need for their constant dosing due to poor separation from effluent impairs economic feasibility. This study used an approach of spatially separating magnetite and granular activated carbon (GAC) from the organic fraction of municipal solid waste (OFMSW) in a single reactor for THSAD. GAC and magnetite addition could both mitigate the severe inhibition of methanogenesis after VFAs build-up to ∼28-30 g/L, while negligible methane production was observed in the control group. The highest methane yield (286 mL CH4/g volatile solids (VS)) was achieved in magnetite-added reactors, while the highest maximum CH4 production rates (26.38 mL CH4/g VS/d) and lowest lag-phase (2.83 days) were obtained in GAC-added reactors. The enrichment of GAC and magnetite biofilms with various syntrophic and potentially electroactive microbial groups (Ruminiclostridium 1, Clostridia MBA03, Defluviitoga, Lentimicrobiaceae) in different relative abundances indicates the existence of specific preferences of these groups for the nature of CM. According to predicted basic metabolic functions, CM can enhance cellular processes and signals, lipid transport and metabolism, and methane metabolism, resulting in improved methane production. Rearrangement of metabolic pathways, formation of pili-like structures, enrichment of biofilms with electroactive groups and a significant improvement in THSAD performance was attributed to the enhancement of the DIET pathway. Promising results obtained in this work due to the spatial separation of the bulk OFMSW and CM can be useful for modeling larger-scale THSAD systems with better recovery of CM and cost-effectiveness.

Genome-resolved correlation mapping links microbial community structure to metabolic interactions driving methane production from wastewater

Anaerobic digestion of municipal mixed sludge produces methane that can be converted into renewable natural gas. To improve economics of this microbial mediated process, metabolic interactions catalyzing biomass conversion to energy need to be identified. Here, we present a two-year time series associating microbial metabolism and physicochemistry in a full-scale wastewater treatment plant. By creating a co-occurrence network with thousands of time-resolved microbial populations from over 100 samples spanning four operating configurations, known and novel microbial consortia with potential to drive methane production were identified. Interactions between these populations were further resolved in relation to specific process configurations by mapping metagenome assembled genomes and cognate gene expression data onto the network. Prominent interactions included transcriptionally active Methanolinea methanogens and syntrophic benzoate oxidizing Syntrophorhabdus, as well as a Methanoregulaceae population and putative syntrophic acetate oxidizing bacteria affiliated with Bateroidetes (Tenuifilaceae) expressing the glycine cleavage bypass of the Wood-Ljungdahl pathway.

Microbial Interactions in Electroactive Biofilms for Environmental Engineering Applications: A Role for Nonexoelectrogens

Microbial electrochemical systems have gained much attention over the past decade due to their potential for various environmental engineering applications ranging from energy production to wastewater treatment to bioproduction. At the heart of these systems lie exoelectrogens-microorganisms capable of exporting electrons generated during metabolism to external electron acceptors such as electrodes. The bacterial biofilm communities on these electrodes are dominated by exoelectrogens but are nonetheless extremely diverse. So far, within the field, the main focus has been on the electroactive bacteria. However, to broaden our understanding of these communities, it is crucial to clarify how the remaining inhabitants of electrode-respiring biofilms contribute to the overall function of the biofilm. Ultimately, such insights may enable improvement of microbial electrochemical systems by reshaping the community structure with naturally occurring beneficial strains.

Effects of various materials used to promote the direct interspecies electron transfer on anaerobic digestion of low-concentration swine manure

The activation of direct interspecies electron transfer (DIET) by the supplementation of conductive materials is one of the effective and available methods to enhance anaerobic digestion (AD). Microorganisms that colonize the surface of these materials form biofilms, the study of which could provide new insights into the character of the DIET process and its effect on AD. The present study focused on AD performance, microbial community, as well as morphological and topological features of biofilms on various materials used to promote DIET during AD of low-concentration swine manure. The best AD characteristics were observed in stainless steel mesh (SM)/digested cow manure (CM) and polyester felt (PF)/digested sewage sludge (SS) combinations used as material/inoculum, respectively. Thus, potential methane yields in CM-SM and SS-PF were up to 26.4% and 26.2% higher compared to the corresponding controls. Microbial analysis of biofilms revealed the dominance of putatively syntrophic bacteria of the MBA03 group of the Limnochordia class in CM inoculated reactors, and syntrophic proteolytic bacteria of the genus Coprothermobacter and acetogenic Clostridium sensu stricto 1, known for their ability to carry out DIET, in SS inoculated reactors. Biofilms on non-conductive materials contained pili-like structures, which were observed only in SS inoculated reactors. Polyester felt tended to biofoul better than carbon felt, resulting in up to 2.8, 3.2 and 1.8 higher nucleic acid, extracellular polymeric substances, and total biomass content, respectively, depending on the inoculum. These results provide new insights into the different types of DIET that can occur in low-loaded AD systems with attached growth.

Food waste bioconversion into new food: A mini-review on nutrients circularity in the production of mushrooms, microalgae and insects

The global challenge of feeding an ever-increasing world population is leading scientists' attention towards nutritious and sustainable foods whose production should have low impacts on environment, economy and society. In case the input feedstock can be waste nutrients, the label of such productions becomes even greener. Nutrients circularity is nowadays an important circular economy practice. This mini-review focuses on the valorisation of food waste as precious biomass to grow new food and feed. In particular, three functional edibles are discussed in the present paper: mushrooms, microalgae and insects. These foods are part of people diets since ages in certain areas of the world and the original aspect of their cultivation and breeding found on waste nutrients recovery is here reviewed. Proofs of such food waste biorefinery viability are already given by several researches featuring the main traits of a suitable growing medium: optimal pool of nutrients and optimal pH. However, lot of work still needs to be done in order to assess the optimal growth and cultivation conditions and the health security of the harvested/bred edibles. A SWOT factors analysis was performed.

Similar Methanogenic Shift but Divergent Syntrophic Partners in Anaerobic Digesters Exposed to Direct versus Successive Ammonium Additions

During anaerobic digestion (AD) of protein-rich wastewater, ammonium (NH4+) is released by amino acid degradation. High NH4+ concentrations disturb the AD microbiome balance, leading to process impairments. The sensitivity of the AD microbiome to NH4+ and the inhibition threshold depend on multiple parameters, especially the previous microbial acclimation to ammonium stress. However, little is known about the effect of different NH4+ acclimation strategies on the differential expression of key active microbial taxa. Here, we applied NH4+ inputs of increasing intensity (from 1.7 to 15.2 g N-NH4+ liters-1) in batch assays fed with synthetic wastewater, according to two different strategies: (i) direct independent inputs at a unique target concentration and (ii) successive inputs in a stepwise manner. In both strategies, along the NH4+ gradient, the active methanogens shifted from acetoclastic Methanosaeta to Methanosarcina and eventually hydrogenotrophic Methanoculleus. Despite shorter latency times, the successive input modality led to lower methane production rate, lower soluble chemical oxygen demand (sCOD) removal efficiency, and lower half maximal inhibitory concentration, together with higher volatile fatty acid (VFA) accumulation, compared to the independent input modality. These differential performances were associated with a drastically distinct succession pattern of the active bacterial partners in both experiments. In particular, the direct exposure modality was characterized by a progressive enrichment of VFA producers (mainly Tepidimicrobium) and syntrophic VFA oxidizers (mainly Syntrophaceticus) with increasing NH4+ concentration, while the successive exposure modality was characterized by a more dynamic succession of VFA producers (mainly Clostridium, Sporanaerobacter, Terrisporobacter) and syntrophic VFA oxidizers (mainly Tepidanaerobacter, Syntrophomonas). These results bring relevant insights for improved process management through inoculum adaptation, bioaugmentation, or community-driven optimization. IMPORTANCE Anaerobic digestion (AD) is an attractive biotechnological process for wastewater bioremediation and bioenergy production in the form of methane-rich biogas. However, AD can be inhibited by ammonium generated by protein-rich effluent, commonly found in agro-industrial activities. Insights in the microbial community composition and identification of AD key players are crucial for anticipating process impairments in response to ammonium stress. They can also help in defining an optimal microbiome adapted to high ammonium levels. Here, we compared two strategies for acclimation of AD microbiome to increasing ammonium concentration to better understand the effect of this stress on the methanogens and their bacterial partners. Our results suggest that long-term cumulative exposure to ammonia disrupted the AD microbiome more strongly than direct (independent) ammonium additions. We identified bioindicators with different NH4+ tolerance capacity among VFA producers and syntrophic VFA oxidizers.

Hypersaline microbial fuel cell equipped with an oxygen-reducing microbial cathode

Microbial anodes and oxygen reducing microbial cathodes were designed separately under constant polarization at + 0.1 V/SCE in a hypersaline medium (NaCl 45 g/L). They were then associated to design two-compartment microbial fuel cells (MFCs). These MFCs produced up to 209 ± 24 mW m^-2 during a week. This was the first demonstration that hypersaline MFCs equipped with microbial cathodes can produce power density at this level. Desulfuromonas sp. were confirmed to be key species of the anodes. The efficiency of the cathodes was linked to the development of a redox system centred at + 0.2 V/SCE and to the presence of Gammaproteobacteria (Alteromonadales and Oceanospirillales), especially an unclassified order phylogenetically linked to the genus Thioalobacter. Comparing the different performance of the four MFCs with the population analyses suggested that polarization at + 0.1 V/SCE should be maintained longer to promote the growth of Thioalobacter on the cathode and thus increase the MFC performance.

Monitoring of seven industrial anaerobic digesters supplied with biochar

BACKGROUND

Recent research articles indicate that direct interspecies electron transfer (DIET) is an alternative metabolic route for methanogenic archaea that improves microbial methane productivity. It has been shown that multiple conductive materials such as biochar can be supplemented to anaerobic digesters to increase the rate of DIET. However, the industrial applicability, as well as the impact of such supplements on taxonomic profiles, has not been sufficiently assessed to date.

RESULTS

Seven industrial biogas plants were upgraded with a shock charge of 1.8 kg biochar per ton of reactor content and then 1.8 kg per ton were added to the substrate for one year. A joint analysis for all seven systems showed a decreasing trend for the concentration of acetic acid (p < 0.0001), propionic acid (p < 0.0001) and butyric acid (p = 0.0022), which was significant in all cases. Quantification of the cofactor F420 using fluorescence microscopy showed a reduction in methanogenic archaea by up to a power of ten. Methanogenic archaea could grow within the biochar, even if the number of cells was 4 times less than in the surrounding sludge. 16S-rRNA gene amplicon sequencing showed a higher microbial diversity in the biochar particles than in the sludge, as well as an accumulation of secondary fermenters and halotolerant bacteria. Taxonomic profiles indicate microbial electroactivity, and show the frequent occurrence of Methanoculleus, which has not been described in this context before.

CONCLUSIONS

Our results shed light on the interplay between biochar particles and microbial communities in anaerobic digesters. Both the microbial diversity and the absolute frequency of the microorganisms involved were significantly changed between sludge samples and biochar particles. This is particularly important against the background of microbial process monitoring. In addition, it could be shown that biochar is suitable for reducing the content of inhibitory, volatile acids on an industrial scale.

How can ethanol enhance direct interspecies electron transfer in anaerobic digestion?

Anaerobic digestion (AD) of organic waste to produce biogas is a mature biotechnology commercialised for decades. However, the relatively recent discovery of direct interspecies electron transfer (DIET) brings a new opportunity to improve the efficiency of biogas technology. DIET may replace mediated interspecies electron transfer (MIET) by efficient electron transfer between exoelectrogens and electrotrophic methanogens, thereby enhancing yields and rates of biogas production. Ethanol, as the initial electron donor in the discovery of the DIET pathway, is now a "hot topic" in the literature. Recent studies have indicated that ethanol in AD functions not only as the substrate, but also as the precursor to stimulate DIET by enriching exoelectrogens and electrotrophic methanogens for co-digesting complex organic wastes. This review aims to highlight the state of the art and recent advances in ethanol-based DIET in AD. The DIET associated reactions of ethanol oxidation and carbon dioxide reduction are assessed by thermodynamic analysis to reveal the extent of the potential for improvement of the AD processes that utilizes DIET pathways. Three ethanol-based DIET strategies are discussed: (1) ethanol as the sole substrate supplemented with conductive materials in AD, (2) ethanol co-digestion with complex substrates and (3) ethanol-type fermentation prior to AD. This review aims to chart the pathways for improved AD performance by utilizing ethanol-based DIET in specific treatments of biological wastes.

Effect of iron oxide content and microstructural porosity on the performance of ceramic membranes as microbial fuel cell separators

•

Suitable bioelectrochemical application of ceramic clays with varying Fe2O3 content.

•

5.75% of Fe2O3 and 1100 °C of sintering temperature allow MFCs to reach 1.045 mW.

•

The Fe2O3 content mitigates the effect of porosity features on the MFC power output.

•

Good stability of the MFCs working during 65 days in continuous mode.

Ceramic materials based on naturally occurring clays are a low cost and environmentally friendly alternative to commercial polymer-based membranes in bioelectrochemical systems. In this work, ceramic membranes containing different amounts of iron oxide (1.06, 2.76 and 5.75 vol.%) and sintered at different temperatures (1100, 1200 and 1300 °C) have been elaborated and tested as separators in urine-fed microbial fuel cells (MFCs). The results reveal that the presence of iron oxide in the ceramic membrane composition increases the structural porosity and reduces the pore size for the three temperatures investigated. On the other hand, it was also observed that the iron content mitigates the negative effect of the high sintering temperature on the power performance of the MFCs. In the case of the ceramic membranes sintered at 1300 °C, power output improved ca. 10-fold when the iron oxide content in the membrane increased from 1.06 up to 5.75 vol.% (30.9 and 286.6 µW, respectively). Amongst the different combinations of iron phase content and sintering temperatures, the maximum power output was obtained by MFCs working with separators containing 5.75 vol. % of iron oxide and sintered at 1100 °C (1.045 mW). Finally, the system was stable for 65 days, which supports the long-term functionality of the different materials assessed.

Effects of foam nickel supplementation on anaerobic digestion: Direct interspecies electron transfer

Stimulating direct interspecies electron transfer with conductive materials is a promising strategy to overcome the limitation of electron transfer efficiency in syntrophic methanogenesis of industrial wastewater. This paper assessed the impact of conductive foam nickel (FN) supplementation on syntrophic methanogenesis and found that addition of 2.45 g/L FN in anaerobic digestion increased the maximum methane production rate by 27.4 % (on day 3) while decreasing the peak production time by 33 % as compared to the control with no FN. Cumulative methane production from day 2 to 6 was 14.5 % higher with addition of 2.45 g/L FN than in the control. Levels of FN in excess of 2.45 g/L did not show benefits. Cyclic voltammetry results indicated that the biofilm formed on the FN could generate electrons. The dominant bacterial genera in suspended sludge were Dechlorobacter and Rikenellaceae DMER64, whereas that in the FN biofilm was Clostridium sensu stricto 11. The dominant archaea Methanosaeta in the FN biofilm was enriched by 14.1 % as compared to the control.

Biomethanation processes: new insights on the effect of a high H2 partial pressure on microbial communities

BACKGROUND

Biomethanation is a promising solution to upgrade the CH₄ content in biogas. This process consists in the injection of H₂ into an anaerobic digester, using the capacity of indigenous hydrogenotrophic methanogens for converting the injected H₂ and the CO₂ generated from the anaerobic digestion process into CH₄. However, the injection of H₂ could cause process disturbances by impacting the microbial communities of the anaerobic digester. Better understanding on how the indigenous microbial community can adapt to high H₂ partial pressures is therefore required.

RESULTS

Seven microbial inocula issued from industrial bioprocesses treating different types of waste were exposed to a high H₂ partial pressure in semi-continuous reactors. After 12 days of operation, even though both CH₄ and volatile fatty acids (VFA) were produced as end products, one of them was the main product. Acetate was the most abundant VFA, representing up to 94% of the total VFA production. VFA accumulation strongly anti-correlated with CH₄ production according to the source of inoculum. Three clusters of inocula were distinguished: (1) inocula leading to CH₄ production, (2) inocula leading to the production of methane and VFA in a low proportion, and (3) inocula leading to the accumulation of mostly VFA, mainly acetate. Interestingly, VFA accumulation was highly correlated to a low proportion of archaea in the inocula, a higher amount of homoacetogens than hydrogenotrophic methanogens and, the absence or the very low abundance in members from the Methanosarcinales order. The best methanogenic performances were obtained when hydrogenotrophic methanogens and Methanosarcina sp. co-dominated all along the operation.

CONCLUSIONS

New insights on the microbial community response to high H₂ partial pressure are provided in this work. H₂ injection in semi-continuous reactors showed a significant impact on microbial communities and their associated metabolic patterns. Hydrogenotrophic methanogens, Methanobacterium sp. or Methanoculleus sp. were highly selected in the reactors, but the presence of co-dominant Methanosarcinales related species were required to produce higher amounts of CH₄ than VFA.

The new insight about electrode interface behaviour via in situ ultrasound three-dimensional representation monitoring based on a bio-electrochemical system

Behaviour of the electrode interface is a determining factor that affects the performance of a bio-electrochemical system (BES). Examples include the formation of an electroactive biofilm, electrode degradation and renewal. However, underlying mechanisms are unclear, and traditional approaches make it difficult to achieve in situ monitoring. In this study, a novel technology using ultrasound three-dimensional representation (UTDR) was used to track in situ electrode interface behaviour based on the correspondence between acoustic and electrical signals. A series of wavelet analyses showed that the formation of an electroactive biofilm is a lengthy process with multiple physiological steps, and biofilm thickness increased by approximately 600 μm after 40 days of operation. At the same time, directional migration of Ca²⁺, Mg²⁺ confirmed acceleration of the salting out on the cathode, which forms a compacted structure with the biological layer. Furthermore, UTDR combined with electrochemical methods allowed for comprehensive evaluation of AC impact, and indicated that AC (1 Hz, 20 V) could effectively desquamate the contaminating solids and restore power density to 93.4% of initial. These results show that UTDR is a sensitive and effective method for revealing microscopic changes on the electrode surface, which gives it potential wide applicability to interfacial processes.

Comparative study of industrial-scale high-solid biogas production from food waste: Process operation and microbiology

Anaerobic high-solid treatment (HST) for processing food waste and biogas production is a viable technology with considerable commercial potential. In this study, we examined and compared mesophilic and thermophilic industrial-scale plug-flow digesters. The HSTs demonstrated reasonable biogas yields from food waste (0.4-0.6 Nm³ CH₄/kg volatile solids). However, during operation at thermophilic conditions ammonia inhibition (~2 g NH₃-N/L) and acid accumulation (6-14 g/L) caused severe process disturbance. Microbial community structures diverged between the processes, with temperature appearing to be a strong driver. A unique feature of the thermophilic HSTs was high abundance of the uncultivated Clostridia group MBA03 and temperature fluctuations in one mesophilic HST were linked to drastically decreased abundance of methanogens and relative abundance of Cloacimonetes. The process data obtained in this study clearly demonstrate both potential and challenges in HST of food waste but also possibilities for management approaches to tackle process imbalance and restore process function.

Adding Zero-Valent Iron to Enhance Electricity Generation during MFC Start-Up

The low power generation efficiency of microbial fuel cells (MFCs) is always a barrier to further development. An attempt to enhance the start-up and electricity generation of MFCs was investigated by adding different doses of zero-valent iron into anaerobic anode chambers in this study. The results showed that the voltage (289.6 mV) of A2 with 0.5 g of zero-valent iron added was higher than the reference reactor (197.1 mV) without dosing zero-valent iron (A4). The maximum power density of 27.3 mW/m2 was obtained in A2. CV analysis demonstrated that A2 possessed a higher oxidation-reduction potential, hence showing a stronger oxidizing property. Meanwhile, electrochemical impedance analysis (EIS) also manifested that values of RCT of carbon felts with zero-valent iron supplemented (0.01-0.03 Ω) were generally lower. What is more, SEM images further proved and illustrated that A2 had compact and dense meshes with a hierarchical structure rather than a relatively looser biofilm in the other reactors. High-throughput sequencing analysis also indicated that zero-valent iron increased the abundance of some functional microbial communities, such as Acinetobacter, Ignavibacteriales, Shewanella, etc.

A novel green approach for fabricating visible, light sensitive nano-broccoli-like antimony trisulfide by marine Sb(v)-reducing bacteria: Revealing potential self-purification in coastal zones

Antimony trisulfide (Sb₂S₃) is industrially important for processes ranging from a semiconductor dopant through batteries to a flame retardant. Approaches for fabricating Sb₂S₃ nanostructures or thin films are by chemical or physicochemical methods, while there have been no report focused on the biological synthesis of nano Sb₂S₃. In the present study, we fabricated nano-broccoli-like Sb₂S₃ using Sb(V) reducing bacteria. Thirty four marine and terrestrial strains are capable of fabricating Sb₂S₃ after 1-5 days of incubation in different selective media. The nano-broccoli-like bio-Sb₂S₃ was light sensitive between 400-550 nm, acting as a photo-catalyst with the bandgap energy of 1.84 eV. Moreover, kinetic and mechanism studies demonstrated that a k value of ∼0.27 h^-1 with an R² = 0.99. The bio-Sb₂S₃ supplemented system exhibited approximately 18.4 times higher photocatalytic activity for degrading methyl orange (MO) to SO₄^2-, CO₂ and H₂O compared with that of control system, which had a k value of ∼0.015 h^-1 (R² = 0.99) under visible light. Bacterial community shift analyses showed that the addition of S or Fe species to the media significantly changed the bacterial communities driven by antimony stress. From this work it appears Clostridia, Bacilli and Gammaproteobacteria from marine sediment are potentially ideal candidates for fabricating bio-Sb₂S₃ due to their excellent electron transfer capability. Based on the above results, we propose a potential visible light bacterially catalyzed self-purification of both heavy metal and persistent organic contamination polluted coastal waters.

Response to starvation and microbial community composition in microbial fuel cells enriched on different electron donors

In microbial fuel cells (MFCs), microorganisms generate electrical current by oxidizing organic compounds. MFCs operated with different electron donors harbour different microbial communities, and it is unknown how that affects their response to starvation. We analysed the microbial communities in acetate- and glucose-fed MFCs and compared their responses to 10 days starvation periods. Each starvation period resulted in a 4.2 ± 1.4% reduction in electrical current in the acetate-fed MFCs and a 10.8 ± 3.9% reduction in the glucose-fed MFCs. When feed was resumed, the acetate-fed MFCs recovered immediately, whereas the glucose-fed MFCs required 1 day to recover. The acetate-fed bioanodes were dominated by Desulfuromonas spp. converting acetate into electrical current. The glucose-fed bioanodes were dominated by Trichococcus sp., functioning as a fermenter, and a member of Desulfuromonadales, using the fermentation products to generate electrical current. Suspended biomass and biofilm growing on non-conductive regions within the MFCs had different community composition than the bioanodes. However, null models showed that homogenizing dispersal of microorganisms within the MFCs affected the community composition, and in the glucose-fed MFCs, the Trichococcus sp. was abundant in all locations. The different responses to starvation can be explained by the more complex pathway requiring microbial interactions to convert glucose into electrical current.

Microbial recycling cells: First steps into a new type of microbial electrochemical technologies, aimed at recovering nutrients from wastewater

The aim of this work were to study terracotta-based porous air-water separators (4 mm thickness) in microbial recycling cells (MRCs) fed with cow manure (CM), swine manure (SM) and dairy wastewater (DW). Over 125 days, besides the removal of 60-90% of soluble-COD, considerable fractions of the main macronutrients (C, N, P, K, Fe, Mn, Ca, Mg) were removed from the wastewater and deposited on the terracotta separators as both inorganic salts and biomass deposits. Water evaporation at air-water interface as well as the high cathodic pH (10-12), induced by oxygen reduction to OH^-, were the predominant factors leading to precipitation. The separators were saturated of up to 10 g per kg of terracotta of the main macronutrients, with negligible concentrations of the main inorganic contaminants. These materials could be directly reused as nutrients-enriched solid conditioners for agricultural soils.

Regenerated silk fibroin membranes as separators for transparent microbial fuel cells

In recent years novel applications of bioelectrochemical systems are exemplified by phototrophic biocathodes, biocompatible enzymatic fuel cells and biodegradable microbial fuel cells (MFCs). Herein, transparent silk fibroin membranes (SFM) with various fibroin content (2%, 4% and 8%) were synthesised and employed as separators in MFCs and compared with standard cation exchange membranes (CEM) as a control. The highest real-time power performance of thin-film SFM was reached by 2%-SFM separators: 25.7 ± 7.4 μW, which corresponds to 68% of the performance of the CEM separators (37.7 ± 3.1 μW). Similarly, 2%-SFM revealed the highest coulombic efficiency of 6.65 ± 1.90%, 74% of the CEM efficiency. Current for 2%-SFM reached 0.25 ± 0.03 mA (86% of CEM control). Decrease of power output was observed after 23 days for 8% and 4% and was a consequence of deterioration of SFMs, determined by physical, chemical and biological studies. This is the first time that economical and transparent silk fibroin polymers were successfully employed in MFCs.

Dynamic evolution of anodic biofilm when maturing under different external resistive loads in microbial fuel cells. Electrochemical perspective

Appropriate inoculation and maturation may be crucial for shortening the startup time and maximising power output of Microbial Fuel Cells (MFCs), whilst ensuring stable operation. In this study we explore the relationship between electrochemical parameters of MFCs matured under different external resistance (R_ext) values (50 Ω - 10 kΩ) using non-synthetic fuel (human urine). Maturing the biofilm under the lower selected R_ext results in improved power performance and lowest internal resistance (R_int), whereas using higher R_ext results in increased ohmic losses and inferior performance. When the optimal load is applied to the MFCs following maturity, dependence of microbial activity on original R_ext values does not change, suggesting an irreversible effect on the biofilm, within the timeframe of the reported experiments. Biofilm microarchitecture is affected by R_ext and plays an important role in MFC efficiency. Presence of water channels, EPS and precipitated salts is distinctive for higher R_ext and open circuit MFCs. Correlation analysis reveals that the biofilm changes most dynamically in the first 5 weeks of operation and that fixed R_ext lefts an electrochemical effect on biofilm performance. Therefore, the initial conditions of the biofilm development can affect its long-term structure, properties and activity.

New insights in photosynthetic microbial fuel cell using anoxygenic phototrophic bacteria

Anoxygenic phototrophic bacteria (APB) pay a key role in biogeochemical cycles, and it can convert light energy to chemical energy by photosynthesis process. Photosynthetic microbial fuel cell (photo-MFC) is regarded as a promising energy-harvesting technology, which is also applied to environment treatment in recent years. The previous studies show that photo-MFC with APB have higher power putout than other bioelectrochemical systems. However, photo-MFC with APB is not reviewed due to some limited factors in the development process. In this review, photo-MFC with APB is treated according to its electron transfer pathways, the current understanding, APB strains, application, influence of substrates, and economic assessment. Meanwhile, knowledge of photosynthesis components and electron transfer pathways of APB is crucial for developing new energy and easing the serious energy crisis. Moreover, some new insights (the optimization of light source and self-sustaining bioelectricity generation) are proposed for the future explorations.

Enhancement of microbial fuel cell performance by introducing a nano-composite cathode catalyst

Iron aminoantipyrine (Fe-AAPyr), graphene nanosheets (GNSs) derived catalysts and their physical mixture Fe-AAPyr-GNS were synthesized and investigated as cathode catalysts for oxygen reduction reaction (ORR) with the activated carbon (AC) as a baseline. Fe-AAPyr catalyst was prepared by Sacrificial Support Method (SSM) with silica as a template and aminoantipyrine (AAPyr) as the organic precursor. 3D-GNS was prepared using modified Hummers method technique. The Oxygen Reduction Reaction (ORR) activity of these catalysts at different loadings was investigated by using rotating ring disk (RRDE) electrode setup in the neutral electrolyte. The performance of the catalysts integrated into air-breathing cathode was also investigated. The co-presence of GNS (2 mg cm⁻²) and Fe-AAPyr (2 mg cm⁻²) catalyst within the air-breathing cathode resulted in the higher power generation recorded in MFC of 235 ± 1 μW cm⁻². Fe-AAPyr catalyst itself showed high performance (217 ± 1 μW cm⁻²), higher compared to GNS (150 ± 5 μW cm⁻²) while AC generated power of roughly 104 μW cm⁻².

•

Fe-AAPyr and GNS were synthesized and characterized.

•

Rotating ring disk electrode (RRDE) setup was performed in the neutral electrolyte.

•

Fe-AAPyr had higher half wave potential and lower H₂O₂ production.

•

The combination of Fe-AAPyr and GNS led to a power generation of 235 ± 1 μWcm⁻².

•

Both Fe-AAPyr and GNS outperformed compared to activated carbon control.

A year of monitoring 20 mesophilic full-scale bioreactors reveals the existence of stable but different core microbiomes in bio-waste and wastewater anaerobic digestion systems

BACKGROUND

Anaerobic digestion (AD) is a microbe-driven process of biomass decomposition to CH₄ and CO₂. In addition to renewable and cost-effective energy production, AD has emerged in the European Union as an environmentally friendly model of bio-waste valorisation and nutrient recycling. Nevertheless, due to the high diversity of uncharacterised microbes, a typical AD microbiome is still considered as "dark matter".

RESULTS

Using the high-throughput sequencing of small rRNA gene, and a monthly monitoring of the physicochemical parameters for 20 different mesophilic full-scale bioreactors over 1 year, we generated a detailed view of AD microbial ecology towards a better understanding of factors that influence and shape these communities. By studying the broadly distributed OTUs present in over 80% of analysed samples, we identified putatively important core bacteria and archaea to the AD process that accounted for over 70% of the whole microbial community relative abundances. AD reactors localised at the wastewater treatment plants were shown to operate with distinct core microbiomes than the agricultural and bio-waste treating biogas units. We also showed that both the core microbiomes were composed of low (with average community abundance ≤ 1%) and highly abundant microbial populations; the vast majority of which remains yet uncharacterised, e.g. abundant candidate Cloacimonetes. Using non-metric multidimensional scaling, we observed microorganisms grouping into clusters that well reflected the origin of the samples, e.g. wastewater versus agricultural and bio-waste treating biogas units. The calculated diversity patterns differed markedly between the different community clusters, mainly due to the presence of highly diverse and dynamic transient species. Core microbial communities appeared relatively stable over the monitoring period.

CONCLUSIONS

In this study, we characterised microbial communities in different AD systems that were monitored over a 1-year period. Evidences were shown to support the concept of a core community driving the AD process, whereas the vast majority of dominant microorganisms remain yet to be characterised.