Performance of a multilayered small-diameter vascular scaffold dual-loaded with VEGF and PDGF

A heparin-functionalized bioink with sustained delivery of vascular endothelial growth factor for 3D bioprinting of prevascularized dermal constructs

Skin tissue engineering faces challenges due to the absence of vascular architecture, impeding the development of permanent skin replacements. To address this, a heparin-functionalized 3D-printed bioink (GH/HepMA) was formulated to enable sustained delivery of vascular endothelial growth factor (VEGF), comprising 0.3 % (w/v) hyaluronic acid (HA), 10 % (w/v) gelatin methacrylate (GelMA), and 0.5 % (w/v) heparin methacrylate (HepMA). The bioink was then used to print dermal constructs with angiogenic functions, including fibroblast networks and human umbilical vein endothelial cell (HUVEC) networks. GH/HepMA, with its covalently cross-linked structure, exhibits enhanced mechanical properties and heparin stability, allowing for a 21-day sustained delivery of VEGF. Cytocompatibility experiments showed that the GH/HepMA bioink supported fibroblast proliferation and promoted collagen I production. With VEGF present, the GH/HepMA bioink promoted HUVEC proliferation, migration, as well as the formation of a richer capillary-like network. Furthermore, HA within the GH/HepMA bioink enhanced rheological properties and printability. Additionally, 3D-bioprinted dermal constructs showed significant deposition of collagen I and III and mature stable capillary-like structures along the axial direction. In summary, this study offers a promising approach for constructing biomimetic multicellular skin substitutes with angiogenesis-induced functions.

Physicochemical, in vitro and in vivo evaluation of VEGF loaded PCL-mPEG and PDGF loaded PCL-Chitosan dual layered vascular grafts

The present study has attempted to evaluate the endothelialization and smooth muscle regeneration efficiency of a novel dual-layer small-diameter vascular graft. Two types of layers (PCL-mPEG-VEGF and PCL-Chitosan-PDGF) were fabricated to find out the best layer giving endothelialization support for the lumen and unique contractile function for outer layer of blood vessels. Platelet-derived growth factor (PDGF) and chitosan were immobilized onto PCL surface by aminolysis-based surface modification technique. Besides, Poly (ethylene glycol) methyl ether (mPEG) and vascular endothelial growth factor (VEGF) were directly blended with PCL. Morphological analysis of membranes ensured consistency of average fibers diameter with native extracellular matrix. A favorable interaction of PCL-mPEG-VEGF with cow pulmonary endothelial cells (CPAEs) and PCL-Chitosan-PDGF with rat bone marrow mesenchymal stem cells (RBMSCs) was obtained during in vitro study. Controlled growth factor release patterns were found from both layers. Further, PCL-mPEG-VEGF exhibited endothelial markers expression properties from RBMSCs. Up-regulation of SMCs markers expression was significantly ensured by the PCL-Chitosan-PDGF membrane. Thus, PCL-mPEG-VEGF and PCL-Chitosan-PDGF were preferred as inner and outer layers respectively of a finally prepared tubular hybrid tissue engineered small diameter vascular graft. Finally, the dual-layer vascular graft was implanted onto a rat abdominal aorta model for 2 months. The extracted samples exhibited the presence of endothelial marker (ICAM 1) in the inner layer and smooth muscle cell marker (αSMA) in the outer layer as well as substantial amount of collagen deposition was observed in the both layers.

In vitro formation and extended culture of highly metabolically active and contractile tissues

3D cell culture models have gained popularity in recent years as an alternative to animal and 2D cell culture models for pharmaceutical testing and disease modeling. Polydimethylsiloxane (PDMS) is a cost-effective and accessible molding material for 3D cultures; however, routine PDMS molding may not be appropriate for extended culture of contractile and metabolically active tissues. Failures can include loss of culture adhesion to the PDMS mold and limited culture surfaces for nutrient and waste diffusion. In this study, we evaluated PDMS molding materials and surface treatments for highly contractile and metabolically active 3D cell cultures. PDMS functionalized with polydopamine allowed for extended culture duration (14.8 ± 3.97 days) when compared to polyethylamine/glutaraldehyde functionalization (6.94 ± 2.74 days); Additionally, porous PDMS extended culture duration (16.7 ± 3.51 days) compared to smooth PDMS (6.33 ± 2.05 days) after treatment with TGF-β2 to increase culture contraction. Porous PDMS additionally allowed for large (13 mm tall × 8 mm diameter) constructs to be fed by diffusion through the mold, resulting in increased cell density (0.0210 ± 0.0049 mean nuclear fraction) compared to controls (0.0045 ± 0.0016 mean nuclear fraction). As a practical demonstration of the flexibility of porous PDMS, we engineered a vascular bioartificial muscle model (VBAM) and demonstrated extended culture of VBAMs anchored with porous PDMS posts. Using this model, we assessed the effect of feeding frequency on VBAM cellularity. Feeding 3×/week significantly increased nuclear fraction at multiple tissue depths relative to 2×/day. VBAM maturation was similarly improved in 3×/week feeding as measured by nuclear alignment (23.49° ± 3.644) and nuclear aspect ratio (2.274 ± 0.0643) relative to 2x/day (35.93° ± 2.942) and (1.371 ± 0.1127), respectively. The described techniques are designed to be simple and easy to implement with minimal training or expense, improving access to dense and/or metabolically active 3D cell culture models.

Functional regeneration at the blood-biomaterial interface

The use of cardiovascular implants is commonplace in clinical practice. However, reproducing the key bioactive and adaptive properties of native cardiovascular tissues with an artificial replacement is highly challenging. Exciting new treatment strategies are under development to regenerate (parts of) cardiovascular tissues directly in situ using immunomodulatory biomaterials. Direct exposure to the bloodstream and hemodynamic loads is a particular challenge, given the risk of thrombosis and adverse remodeling that it brings. However, the blood is also a source of (immune) cells and proteins that dominantly contribute to functional tissue regeneration. This review explores the potential of the blood as a source for the complete or partial in situ regeneration of cardiovascular tissues, with a particular focus on the endothelium, being the natural blood-tissue barrier. We pinpoint the current scientific challenges to enable rational engineering and testing of blood-contacting implants to leverage the regenerative potential of the blood.

Multi-material electrospinning: from methods to biomedical applications

Electrospinning as a versatile, simple, and cost-effective method to engineer a variety of micro or nanofibrous materials, has contributed to significant developments in the biomedical field. However, the traditional electrospinning of single material only can produce homogeneous fibrous assemblies with limited functional properties, which oftentimes fails to meet the ever-increasing requirements of biomedical applications. Thus, multi-material electrospinning referring to engineering two or more kinds of materials, has been recently developed to enable the fabrication of diversified complex fibrous structures with advanced performance for greatly promoting biomedical development. This review firstly gives an overview of multi-material electrospinning modalities, with a highlight on their features and accessibility for constructing different complex fibrous structures. A perspective of how multi-material electrospinning opens up new opportunities for specific biomedical applications, i.e., tissue engineering and drug delivery, is also offered.

Tissue-engineered small-diameter vascular grafts containing novel copper-doped bioactive glass biomaterials to promote angiogenic activity and endothelial regeneration

Small-diameter vascular grafts frequently fail because of obstruction and infection. Despite the wide range of commercially available vascular grafts, the anatomical uniqueness of defect sites demands patient-specific designs. This study aims to increase the success rate of implantation by fabricating bilayer vascular grafts containing bioactive glasses (BGs) and modifying their composition by removing hemostatic ions to make them blood-compatible and to enhance their antibacterial and angiogenesis properties. The porous vascular graft tubes were 3D printed using polycaprolactone, polyglycerol sebacate, and the modified BGs. The polycaprolactone sheath was then wrapped around the 3D-printed layer using the electrospinning technique to prevent blood leakage. The results demonstrated that the incorporation of modified BGs into the polymeric matrix not only improved the mechanical properties of the vascular graft but also significantly enhanced its antibacterial activity against both gram-negative and gram-positive strains. In addition, no hemolysis or platelet activity was detected after incorporating modified BGs into the vascular grafts. Copper-releasing vascular grafts significantly enhanced endothelial cell proliferation, motility, and VEGF secretion. Additionally, In vivo angiogenesis (CD31 immunofluorescent staining) and gene expression experiments showed that copper-releasing vascular grafts considerably promoted the formation of new blood vessels, low-grade inflammation (decreased expression of IL-1β and TNF-α), and high-level angiogenesis (increased expression of angiogenic growth factors including VEGF, PDGF-BB, and HEBGF). These observations indicate that the use of BGs with suitable compositional modifications in vascular grafts may promote the clinical success of patient-specific vascular prostheses by accelerating tissue regeneration without any coagulation problems.

Red blood cell membrane-functionalized Nanofibrous tubes for small-diameter vascular grafts

The off-the-shelf small-diameter vascular grafts (SDVGs) have inferior clinical efficacy. Red blood cell membrane (Rm) has easy availability and multiple bioactive components (such as phospholipids, proteins, and glycoproteins), which can improve the clinic's availability and patency of SDVGs. Here we developed a facile approach to preparing an Rm-functionalized poly-ε-caprolactone/poly-d-lysine (Rm@PCL/PDL) tube by co-incubation and single-step rolling. The integrity, stability, and bioactivity of Rm on Rm@PCL/PDL were evaluated. The revascularization of Rm@PCL/PDL tubes was studied by implantation in the carotid artery of rabbits. Rm@PCL/PDL can be quickly prepared and showed excellent bioactivity with good hemocompatibility and great anti-inflammatory. Rm@PCL/PDL tubes as the substitute for the carotid artery of rabbits had good patency and quick remodeling within 21 days. Rm, as a "self" biomaterial with high biosafety, provides a new and facile approach to developing personalized or universal SDVGs for the clinic, which is of great significance in cardiovascular regenerative medicine and organ chip.

Curcumin Functionalized Electrospun Fibers with Efficient pH Real-Time Monitoring and Antibacterial and Anti-inflammatory Properties

Wound infection has threatened the health of humans, and developing novel dressings by integrating infection detection and wound treatment in biomaterials is urgently required in the medical industry. In this study, we report a facile strategy to develop curcumin functionalized poly(ε-caprolactone) and gelatin composite fibrous membranes with pH real-time monitoring and antibacterial and anti-inflammatory properties. The developed curcumin-functionalized composite fibers displayed highly sensitive and visible response to the variation of the pH value of a buffer solution in the range of 5.6-8.6. In addition, the resultant fibrous membrane showed obviously enhanced antibacterial efficiency against both E. coli and S. aureus and no obvious cytotoxicity to human dermal fibroblasts when the curcumin content was less than 5 wt %. More importantly, 3 wt % curcumin-functionalized composite membrane exhibited excellent anti-inflammatory activities, good antioxidant activity of ca. 82%, and significantly decreased expression levels of pro-inflammatory cytokines like TNF-α and IL-6 in vitro (p < 0.001). Furthermore, subcutaneous embedding experiments showed that the 3 wt % curcumin-functionalized membrane significantly promoted cell penetration, recruited less macrophages, and facilitated collage deposition. Therefore, the curcumin-functionalized composite fibers could be employed to fabricate multifunctional dressings for the future treatment of chronic wounds.

Effects of Chemical Composition on the Shape Memory Property of Poly(dl-lactide-co-trimethylene carbonate) as Self-Morphing Small-Diameter Vascular Scaffolds

Smart materials have great potential in many biomedical applications, in which biodegradable shape memory polymers (SMPs) can be used as surgical sutures, implants, and stents. Poly(dl-lactide-co-trimethylene carbonate) (PDLLTC) represents one of the promising SMPs and is widely used in biomedical applications. However, the relationship between its shape memory property and chemical structure has not been fully studied and needs further elaboration. In this work, PDLLTC copolymers in different compositions have been synthesized, and their shape memory properties have been investigated. It has been found that the shape memory property is related to the chemical composition and polymeric chain segments. The copolymer with a DLLA/TMC ratio of 75:25 (PDLLTC7525) has been demonstrated with great shape fixation and recovery ratio at human body temperature. Furthermore, PDLLTC7525-based self-morphing small-diameter vascular scaffolds adhered with inner electrospun aligned gelatin/hyaluronic acid (Gel/HA) nanofibers have been constructed, as a merit of its shape memory property. The scaffolds have been demonstrated to facilitate the proliferation and adhesion of endothelial cells on the inner layer. Therefore, PDLLTC with tailorable shape memory properties represents a promising candidate for the development of SMPs, as well as for small-diameter vascular scaffolds construction.

Electrospun membranes of carboxylated poly(ester urethane)urea/gelatin encapsulating pterostilbene for adaptive and antioxidative purposes

Oxidative stress caused by the harsh microenvironment after implantation of an artificial graft with mismatching mechanical properties usually triggers inflammation responses, which have adverse impacts on tissue regeneration. For coping with these problems, in this work, bioactive fibrous scaffolds were developed from specially synthesized carboxylated poly(ester urethane)urea (PEUU) and gelatin (Gel) by encapsulating pterostilbene (Pte) for the first time. The prepared electrospun membranes exhibited self-adaptable mechanical properties with high elasticity owing to the bonded electrospun fibers, cross-linking network between PEUU and Gel, and the inherent flexibility of the PEUU polymer in the fibrous matrix. The PEUU/Gel/Pte electrospun membrane containing 7% Pte could promote in vitro proliferation of human umbilical vein endothelial cells, and regulate vascular smooth muscle cells with excellent antioxidant properties via free radical scavenging. In vivo results in a rat subcutaneous implantation model further demonstrated the positive effect of the specially prepared PEUU/Gel/Pte scaffold on both normal cell growth and anti-inflammatory by promoting cellularization and polarizing macrophages toward the M2 phenotype. These PEUU/Gel/Pte electrospun membranes with adaptability benefit to tissue regeneration by modulating inflammation responses, especially applications in vascular regeneration.

Spatiotemporal Delivery of pBMP2 and pVEGF by a Core-Sheath Structured Fiber-Hydrogel Gene-Activated Matrix Loaded with Peptide-Modified Nanoparticles for Critical-Sized Bone Defect Repair

The clinical translation of bioactive scaffolds for the treatment of large segmental bone defects remains a grand challenge. The gene-activated matrix (GAM) combining gene therapy and tissue engineering scaffold offers a promising strategy for the restoration of structure and function of damaged or dysfunctional tissues. Herein, a gene-activated biomimetic composite scaffold consisting of an electrospun poly(ε-caprolactone) fiber sheath and an alginate hydrogel core which carried plasmid DNA encoding bone morphogenetic protein 2 (pBMP2) and vascular endothelial growth factor (pVEGF), respectively, is developed. A peptide-modified polymeric nanocarrier with low cytotoxicity and high efficiency serves as the nonviral DNA delivery vector. The obtained GAM allows spatiotemporal release of pVEGF and pBMP2 and promotes osteogenic differentiation of preosteoblasts in vitro. In vivo evaluation using a critical-sized segmental femoral defect model in rats shows that the dual gene delivery system can significantly accelerate bone healing by activating angiogenesis and osteogenesis. These findings demonstrate the effectiveness of the developed dual gene-activated core-sheath structured fiber-hydrogel composite scaffold for critical-sized bone defect regeneration and the potential of cell-free scaffold-based gene therapy for tissue engineering.

Research Progress on Emerging Polysaccharide Materials Applied in Tissue Engineering

The development and application of polysaccharide materials are popular areas of research. Emerging polysaccharide materials have been widely used in tissue engineering fields such as in skin trauma, bone defects, cartilage repair and arthritis due to their stability, good biocompatibility and reproducibility. This paper reviewed the recent progress of the application of polysaccharide materials in tissue engineering. Firstly, we introduced polysaccharide materials and their derivatives and summarized the physicochemical properties of polysaccharide materials and their application in tissue engineering after modification. Secondly, we introduced the processing methods of polysaccharide materials, including the processing of polysaccharides into amorphous hydrogels, microspheres and membranes. Then, we summarized the application of polysaccharide materials in tissue engineering. Finally, some views on the research and application of polysaccharide materials are presented. The purpose of this review was to summarize the current research progress on polysaccharide materials with special attention paid to the application of polysaccharide materials in tissue engineering.

Design and Simulation of the Biomechanics of Multi-Layered Composite Poly(Vinyl Alcohol) Coronary Artery Grafts

Coronary artery disease is among the primary causes of death worldwide. While synthetic grafts allow replacement of diseased tissue, mismatched mechanical properties between graft and native tissue remains a major cause of graft failure. Multi-layered grafts could overcome these mechanical incompatibilities by mimicking the structural heterogeneity of the artery wall. However, the layer-specific biomechanics of synthetic grafts under physiological conditions and their impact on endothelial function is often overlooked and/or poorly understood. In this study, the transmural biomechanics of four synthetic graft designs were simulated under physiological pressure, relative to the coronary artery wall, using finite element analysis. Using poly(vinyl alcohol) (PVA)/gelatin cryogel as the representative biomaterial, the following conclusions are drawn: (I) the maximum circumferential stress occurs at the luminal surface of both the grafts and the artery; (II) circumferential stress varies discontinuously across the media and adventitia, and is influenced by the stiffness of the adventitia; (III) unlike native tissue, PVA/gelatin does not exhibit strain stiffening below diastolic pressure; and (IV) for both PVA/gelatin and native tissue, the magnitude of stress and strain distribution is heavily dependent on the constitutive models used to model material hyperelasticity. While these results build on the current literature surrounding PVA-based arterial grafts, the proposed method has exciting potential toward the wider design of multi-layer scaffolds. Such finite element analyses could help guide the future validation of multi-layered grafts for the treatment of coronary artery disease.

Tubular TPU/SF nanofibers covered with chitosan-based hydrogels as small-diameter vascular grafts with enhanced mechanical properties

Native grafts such as internal mammary artery and saphenous vein are the main choice for coronary artery bypass graft. However, due to the limitations associated with their availability and rapid failure caused by hyperplasia, small diameter tissue-engineered vascular grafts (TEVGs) with sufficient post-implantation patency are urgently demanded as artificial alternatives. In our previous work, we innovatively fabricated a bilayer vascular graft providing appropriate structural and biological properties using electrospinning and freeze-drying methods. It was proved that the mechanical properties of the proposed graft enhanced in comparison with using either of methods individually. Here, we adopted the same methods and incorporated an anticoagulant internal layer (inner diameter 4 mm), comprised of co-electrospun fibers of silk fibroin (SF) and heparinized thermoplastic polyurethane (TPU), and an external highly porous hydrogel fabricated by freeze-drying method. The electrospun layer exhibited strong mechanical properties including superior elastic modulus (4.92 ± 0.11 MPa), suture retention force (6.73 ± 0.83 N), elongation at break (196 ± 4%), and comparable burst pressure (1140 ± 12 mmHg) while the external hydrogel provided SMCs viability. The heparin was released in a sustain manner over 40 days, and the cytocompatibility and blood compatibility of scaffold were approved using MTT assay and platelet adhesion test. Thus, the proposed graft has a potential to be used as an artificial blood vessel scaffold for later in-vivo transplantation.

Cardiovascular tissue engineering and regeneration: A plead for further knowledge convergence

Cardiovascular tissue engineering and regeneration strive to provide long-term, effective solutions for a growing group of patients in need of myocardial repair, vascular (access) grafts, heart valves, and regeneration of organ microcirculation. In the past two decades, ongoing convergence of disciplines and multidisciplinary collaborations between cardiothoracic surgeons, cardiologists, bioengineers, material scientists, and cell biologists have resulted in better understanding of the problems at hand and novel regenerative approaches. As a side effect, however, the field has become strongly organized and differentiated around topical areas at risk of reinvention of technologies and repetition of approaches and across the areas. A better integration of knowledge and technologies from the individual topical areas and regenerative approaches and technologies may pave the way towards faster and more effective treatments to cure the cardiovascular system. This review summarizes the evolution of research and regenerative approaches in the areas of myocardial regeneration, heart valve and vascular tissue engineering, and regeneration of microcirculations and discusses previous and potential future integration of these individual areas and developed technologies for improved clinical impact. Finally, it provides a perspective on the further integration of research organization, knowledge implementation, and valorization as a contributor to advancing cardiovascular tissue engineering and regenerative medicine.

New Forms of Electrospun Nanofibers Applied in Cardiovascular Field

Cardiovascular disease (CVD) is one of the leading causes of death worldwide. In recent years, regenerative medicine, tissue engineering and the development of new materials have become the focus of attention this field, and electrospinning technology to prepare nanofibrous materials for the treatment of cardiovascular diseases has attracted people's attention. Unlike previous reviews, this research enumerates the experimental methods and applications of electrospinning technology combined with nanofibrous materials in the directions of myocardial infarction repair, artificial heart valves, artificial blood vessels and cardiovascular patches from the perspective of cardiovascular surgery. In the end, this review also summarizes the limitations, unresolved technical challenges, and possible future directions of this technology for cardiovascular disease applications.

In Situ Prevascularization Strategy with Three-Dimensional Porous Conduits for Neural Tissue Engineering

Neovascularization is crucial for peripheral nerve regeneration and long-term functional restoration. Previous studies have emphasized strategies that enhance axonal repair over vascularization. Here, we describe the development and application of an in situ prevascularization strategy that uses 3D porous nerve guidance conduits (NGCs) to achieve angiogenesis-mediated neural regeneration. The optimal porosity of the NGC is a critical feature for achieving neovascularization and nerve growth patency. Hollow silk fibroin/poly(l-lactic acid-co-ε-caprolactone) NGCs with 3D sponge-like walls were fabricated using electrospinning and freeze-drying. In vitro results showed that 3D porous NGC favored cell biocompatibility had neuroregeneration potential and, most importantly, had angiogenic activity. Results from our mechanistic studies suggest that activation of HIF-1α signaling might be associated with this process. We also tested in situ prevascularized 3D porous NGCs in vivo by transplanting them into a 10 mm rat sciatic nerve defect model with the aim of regenerating the severed nerve. The prevascularized 3D porous NGCs greatly enhanced intraneural angiogenesis, resulting in demonstrable neurogenesis. Eight weeks after transplantation, the performance of the prevascularized 3D NGCs was similar to that of traditional autografts in terms of improved anatomical structure, morphology, and neural function. In conclusion, combining a reasonably fabricated 3D-pore conduit structure with in situ prevascularization promoted functional nerve regeneration, suggesting an alternative strategy for achieving functional recovery after peripheral nerve trauma.

Renal Biology Driven Macro- and Microscale Design Strategies for Creating an Artificial Proximal Tubule Using Fiber-Based Technologies

Chronic kidney disease affects one in six people worldwide. Due to the scarcity of donor kidneys and the complications associated with hemodialysis (HD), a cell-based bioartificial kidney (BAK) device is desired. One of the shortcomings of HD is the lack of active transport of solutes that would normally be performed by membrane transporters in kidney epithelial cells. Specifically, proximal tubule (PT) epithelial cells play a major role in the active transport of metabolic waste products. Therefore, a BAK containing an artificial PT to actively transport solutes between the blood and the filtrate could provide major therapeutic advances. Creating such an artificial PT requires a biocompatible tubular structure which supports the adhesion and function of PT-specific epithelial cells. Ideally, this scaffold should structurally replicate the natural PT basement membrane which consists mainly of collagen fibers. Fiber-based technologies such as electrospinning are therefore especially promising for PT scaffold manufacturing. This review discusses the use of electrospinning technologies to generate an artificial PT scaffold for ex vivo/in vivo cellularization. We offer a comparison of currently available electrospinning technologies and outline the desired scaffold properties required to serve as a PT scaffold. Discussed also are the potential technologies that may converge in the future, enabling the effective and biomimetic incorporation of synthetic PTs in to BAK devices and beyond.

Electrospun nanofiber scaffold for vascular tissue engineering

Due to the prevalence of cardiovascular diseases, there is a large need for small diameter vascular grafts that cannot be fulfilled using autologous vessels. Although medium to large diameter synthetic vessels are in use, no suitable small diameter vascular graft has been developed due to the unique dynamic environment that exists in small vessels. To achieve long term patency, a successful tissue engineered vascular graft would need to closely match the mechanical properties of native tissue, be non-thrombotic and non-immunogenic, and elicit the proper healing response and undergo remodeling to incorporate into the native vasculature. Electrospinning presents a promising approach to the development of a suitable tissue engineered vascular graft. This review provides a comprehensive overview of the different polymers, techniques, and functionalization approaches that have been used to develop an electrospun tissue engineered vascular graft.

Challenges and strategies for in situ endothelialization and long-term lumen patency of vascular grafts

Vascular diseases are the most prevalent cause of ischemic necrosis of tissue and organ, which even result in dysfunction and death. Vascular regeneration or artificial vascular graft, as the conventional treatment modality, has received keen attentions. However, small-diameter (diameter < 4 mm) vascular grafts have a high risk of thrombosis and intimal hyperplasia (IH), which makes long-term lumen patency challengeable. Endothelial cells (ECs) form the inner endothelium layer, and are crucial for anti-coagulation and thrombogenesis. Thus, promoting in situ endothelialization in vascular graft remodeling takes top priority, which requires recruitment of endothelia progenitor cells (EPCs), migration, adhesion, proliferation and activation of EPCs and ECs. Chemotaxis aimed at ligands on EPC surface can be utilized for EPC homing, while nanofibrous structure, biocompatible surface and cell-capturing molecules on graft surface can be applied for cell adhesion. Moreover, cell orientation can be regulated by topography of scaffold, and cell bioactivity can be modulated by growth factors and therapeutic genes. Additionally, surface modification can also reduce thrombogenesis, and some drug release can inhibit IH. Considering the influence of macrophages on ECs and smooth muscle cells (SMCs), scaffolds loaded with drugs that can promote M2 polarization are alternative strategies. In conclusion, the advanced strategies for enhanced long-term lumen patency of vascular grafts are summarized in this review. Strategies for recruitment of EPCs, adhesion, proliferation and activation of EPCs and ECs, anti-thrombogenesis, anti-IH, and immunomodulation are discussed. Ideal vascular grafts with appropriate surface modification, loading and fabrication strategies are required in further studies.

Features of a simvastatin-loaded multi-layered co-electrospun barrier membrane for guided bone regeneration

A novel tri-layer membrane consisting of polycaprolactone (PCL) fibrous sheets and structured nanofibers with a gelatin (Gt) shell and a simvastatin-containing PCL core (PCL-Gt/PCL-simvastatin membrane) was prepared. The soft external layer comprised of Gt/PCL-simvastatin, the external layer of PCL and the middle layer of both microfilaments, interwoven together. The membrane was designed to promote osteoinduction and act as a barrier against cells but not against water and molecules in order to promote guided bone regeneration. The structure of the membrane was characterized by scanning electronic microscopy. The in vitro release rates of simvastatin over 32 days were determined by high-performance liquid chromatography. For in vitro biological assays, bone marrow mesenchymal stem cells and human fibroblasts were cultured on the different surfaces of the membrane. Cell adhesion, proliferation, distribution, and differentiation were examined. For in vivo testing, cranial defects were created in rabbits to assess the amount of new bone formed for each membrane. The results revealed that membranes with multi-layered structures showed good cell viability and effective osteoinductive and barrier properties. These results suggest that the novel multi-layered PCL-Gt/PCL-simvastatin membranes have great potential for bone tissue engineering.

Robust and Antiswelling Hollow Hydrogel Tube with Antibacterial and Antithrombotic Ability for Emergency Vascular Replacement

Infection and thrombosis are the two major complications in almost any indwelling intravascular catheters, leading to adverse consequences. Here, we report a robust and antiswelling hollow hydrogel tube that is prepared by copolymerizing a hydrogen-bonding (H-bonding) monomer and a zinc methacrylate (ZMA) monomer in the absence of any chemical cross-linker. The strong H-bonding interactions from the side chain of N-acryloylsemicarbazide (NASC) endow the hydrogel with high mechanical strength and swelling stability. Introduction of ZMA affords a superhydrophilic surface, and the release of a zinc ion (Zn²⁺) from the hydrogel can kill nearly 100% both of Staphylococcus aureus and Escherichia coli, indicating its excellent antibacterial ability. Importantly, the P(NASC-co-ZMA) hydrogel exhibits better antithrombosis ability due to the resistant adhesion of fibrinogen protein and platelets, as well binding calcium ions (Ca²⁺) from the blood. The hydrogel tube is used to connect the ex vivo arteriovenous shunt circuit or implanted into the left carotid artery in the rabbit model, showing a better patency rate. All of these results suggest that this hydrogel tube may mitigate infection and thrombosis complications, thus holding potential as an artificial blood vessel for emergency vascular replacement.

Recent Progress on Biodegradable Tissue Engineering Scaffolds Prepared by Thermally-Induced Phase Separation (TIPS)

Porous biodegradable scaffolds provide a physical substrate for cells allowing them to attach, proliferate and guide the formation of new tissues. A variety of techniques have been developed to fabricate tissue engineering (TE) scaffolds, among them the most relevant is the thermally-induced phase separation (TIPS). This technique has been widely used in recent years to fabricate three-dimensional (3D) TE scaffolds. Low production cost, simple experimental procedure and easy processability together with the capability to produce highly porous scaffolds with controllable architecture justify the popularity of TIPS. This paper provides a general overview of the TIPS methodology applied for the preparation of 3D porous TE scaffolds. The recent advances in the fabrication of porous scaffolds through this technique, in terms of technology and material selection, have been reviewed. In addition, how properties can be effectively modified to serve as ideal substrates for specific target cells has been specifically addressed. Additionally, examples are offered with respect to changes of TIPS procedure parameters, the combination of TIPS with other techniques and innovations in polymer or filler selection.

Multidrug-loaded electrospun micro/nanofibrous membranes: Fabrication strategies, release behaviors and applications in regenerative medicine

Electrospun micro/nanofibrous membranes (EFMs) have been widely investigated as local drug delivery systems. Multiple drugs can be simultaneously incorporated into one EFM to create synergistic effects, reduce side effects, and play their respective roles in the complex physiological processes of tissue regeneration and postoperative adhesion prevention. Due to the versatile electrospinning techniques, sustained and programmed release behaviors of multiple drugs could be achieved by modulating the structure of the EFMs and the location of the drugs. In this review, various multidrug incorporation approaches based on electrospinning are overviewed. In particular, the advantages and limitations of each drug incorporation technique, the methods to control drug release and the effect of one drug release on another are discussed. Then the applications of multidrug-loaded EFMs in regenerative medicine, including wound healing, bone regeneration, vascular tissue engineering, nerve regeneration, periodontal regeneration and adhesion prevention are comprehensively reviewed. Finally, the future perspectives and challenges in the research of multidrug-loaded EFMs are discussed.

Designed and fabrication of triple-layered vascular scaffold with microchannels

Currently, one of the best preparation strategies for the triple-layered vascular scaffold is to imitate the three-layer structure of natural blood vessels to achieve the biofunctional characteristics of vascular transplantation. Here, we developed a combinatorial method to fabricate triple-layered vascular scaffold (TVS) by using electrospinning and coaxial 3 D printing. First, Polycaprolactone-collagen (PCL-Col) was applied to prepared the inner layer of TVS by electrospinning. Second, egg white/sodium alginate (EW/SA) blend hydrogel was extruded to form hollow filaments by coaxial 3 D printing and crosslinking mechanism, which enwound around the surface of the inner layer in a circumferential direction as the intermediate layer of TVS. Finally, electrospun PCL-Col nanofibers were wrapped on the surface of hydrogel layer as the outer layer of TVS. The morphological characterization and mechanical strength of the fabricated TVS were measured. Compared with natural blood vessels, results shown that ultimate tensile stress (UTS), strain to failure (STF), the estimated burst strength and the suture retention strength (SRS) of TVS were superior. Also, the fabricated TVS exhibits good hydrophilicity and excellent flexibility. Moreover, the biocompatibility of TVS was investigated through human umbilical vein endothelial cells (HUVECs), the results demonstrated that cells can successfully attach the surface of graft and maintain high viability. In summary, all of results demonstrated that this method could fabricate a novel triple-layered vascular scaffold, possessing appropriate mechanical properties and good biological properties, which has the potential to be used in tissue engineered vascular grafts applications.

Protein encapsulation by electrospinning and electrospraying

Given the increasing interest in the use of peptide- and protein-based agents in therapeutic strategies, it is fundamental to develop delivery systems capable of preserving the biological activity of these molecules upon administration, and which can provide tuneable release profiles. Electrohydrodynamic (EHD) techniques, encompassing electrospinning and electrospraying, allow the generation of fibres and particles with high surface area-to-volume ratios, versatile architectures, and highly controllable release profiles. This review is focused on exploring the potential of different EHD methods (including blend, emulsion, and co-/multi-axial electrospinning and electrospraying) for the development of peptide and protein delivery systems. An overview of the principles of each technique is first presented, followed by a survey of the literature on the encapsulation of enzymes, growth factors, antibodies, hormones, and vaccine antigens using EHD approaches. The possibility for localised delivery using stimuli-responsive systems is also explored. Finally, the advantages and challenges with each EHD method are summarised, and the necessary steps for clinical translation and scaled-up production of electrospun and electrosprayed protein delivery systems are discussed.

Considerations in the Development of Small-Diameter Vascular Graft as an Alternative for Bypass and Reconstructive Surgeries: A Review

BACKGROUND

Current design strategies for small diameter vascular grafts (< 6 mm internal diameter; ID) are focused on mimicking native vascular tissue because the commercially available grafts still fail at small diameters, notably due to development of intimal hyperplasia and thrombosis. To overcome these challenges, various design approaches, material selection, and surface modification strategies have been employed to improve the patency of small-diameter grafts.

REVIEW

The purpose of this review is to outline various considerations in the development of small-diameter vascular grafts, including material choice, surface modifications to enhance biocompatibility/endothelialization, and mechanical properties of the graft, that are currently being implanted. Additionally, we have taken into account the general vascular physiology, tissue engineering approaches, and collective achievements of the authors in this area. We reviewed both commercially available synthetic grafts (e-PTFE and PET), elastic polymers such as polyurethane and biodegradable and bioresorbable materials. We included naturally occurring materials by focusing on their potential application in the development of future vascular alternatives.

CONCLUSION

Until now, there are few comprehensive reviews regarding considerations in the design of small-diameter vascular grafts in the literature. Here-in, we have discussed in-depth the various strategies employed to generate engineered vascular graft due to their high demand for vascular surgeries. While some TEVG design strategies have shown greater potential in contrast to autologous or synthetic ePTFE conduits, many are still hindered by high production cost which prevents their widespread adoption. Nonetheless, as tissue engineers continue to develop on their strategies and procedures for improved TEVGs, soon, a reliable engineered graft will be available in the market. Hence, we anticipate a viable TEVG with resorbable property, fabricated via electrospinning approach to hold a greater potential that can overcome the challenges observed in both autologous and allogenic grafts. This is because they can be mechanically tuned, incorporated/surface-functionalized with bioactive molecules and mass-manufactured in a reproducible manner. It is also found that most of the success in engineered vascular graft approaching commercialization is for large vessels rather than small-diameter grafts used as cardiovascular bypass grafts. Consequently, the field of vascular engineering is still available for future innovators that can take up the challenge to create a functional arterial substitute.

Merging 3D printing with electrospun biodegradable small-caliber vascular grafts immobilized with VEGF

The major challenge of commercially available vascular substitutes comes from their limitations in terms of hydrophobic surface, which is hostile to cell growth. To date, tissue-engineered and synthetic grafts have not translated well to clinical trials when looking at small diameters. We conceptualized a cell-free structurally reinforced biodegradable vascular graft recapitulating the anisotropic feature of a native blood vessel. The nanofibrous scaffold is designed in such a way that it will gradually degrade systematically to yield a neo-vessel, facilitated by an immobilized bioactive molecule-vascular endothelial growth factor (VEGF). The nano-topographic cue of the device is capable of direct host cell infiltration. We evaluated the burst pressure, histology, hemocompatibility, compression test, and mechanical analysis of the new graft. The graft implanted into the carotid artery of a porcine model demonstrated a good patency rate as early as two week post-implantation. This graft reinforced design approach when employed in vascular tissue engineering might strongly influencing regenerative medicine.

Long-term results of triple-layered small diameter vascular grafts in sheep carotid arteries

There is an urgent clinical for small diameter vascular grafts (SDVGs) for use in the treatment of coronary artery disease. Moreover, biodegradable SDVGs are drawing increasing attention because they have the potential to restore vascular function with the degradation of vascular graft and tissue regeneration. In this study, we designed triple-layered SDVGs to mimic the native arterial structure, with each layer contributing its unique porosity to the porous structure. We evaluated triple-layered SDVGs in a sheep carotid arterial replacement model. After implantation for 12 months, two grafts were patent and indicated the feasibility of using grafts in large animals. Nevertheless, it was determined that both grafts formed aneurysms at the proximal end. The prevention of such aneurysms remains a challenge for future investigation.

Mechanical Properties of Electrospun, Blended Fibrinogen: PCL Nanofibers

Electrospun nanofibers manufactured from biocompatible materials are used in numerous bioengineering applications, such as tissue engineering, creating organoids or dressings, and drug delivery. In many of these applications, the morphological and mechanical properties of the single fiber affect their function. We used a combined atomic force microscope (AFM)/optical microscope technique to determine the mechanical properties of nanofibers that were electrospun from a 50:50 fibrinogen:PCL (poly-ε-caprolactone) blend. Both of these materials are widely available and biocompatible. Fibers were spun onto a striated substrate with 6 μm wide grooves, anchored with epoxy on the ridges and pulled with the AFM probe. The fibers showed significant strain softening, as the modulus decreased from an initial value of 1700 MPa (5–10% strain) to 110 MPa (>40% strain). Despite this extreme strain softening, these fibers were very extensible, with a breaking strain of 100%. The fibers exhibited high energy loss (up to 70%) and strains larger than 5% permanently deformed the fibers. These fibers displayed the stress–strain curves of a ductile material. We provide a comparison of the mechanical properties of these blended fibers with other electrospun and natural nanofibers. This work expands a growing library of mechanically characterized, electrospun materials for biomedical applications.

Tubular Fibrous Scaffolds Functionalized with Tropoelastin as a Small-Diameter Vascular Graft

Cardiovascular disorders are a healthcare problem in today's society. The clinically available synthetic vascular grafts are thrombogenic and could induce intimal hyperplasia. Rapid endothelialization and matched mechanical properties are two major requirements to be considered when designing functional vascular grafts. Herein, an electrospun tubular fibrous (eTF) scaffold was biofunctionalized with tropoelastin at the luminal surface. The luminal surface functionalization was confirmed by an increase of the zeta potential and by the insertion of NH₂ groups. Tropoelastin was immobilized via its -NH₂ or -COOH groups at the activated or aminolysed eTF scaffolds, respectively, to study the effect of exposed functional groups on human endothelial cells (ECs) behavior. Tensile properties demonstrated that functionalized eTF scaffolds presented strength and stiffness within the range of those of native blood vessels. Tropoelastin immobilized on activated eTF scaffolds promoted higher metabolic activity and proliferation of ECs, whereas when immobilized on aminolysed eTF scaffolds, significantly higher protein synthesis was observed. These biofunctional eTF scaffolds are a promising small-diameter vascular graft that promote rapid endothelialization and have compatible mechanical properties.

HuBiogel incorporated fibro-porous hybrid nanomatrix graft for vascular tissue interfaces

Native extracellular matrix (ECM) possesses the biochemical cues to promote cell survival. However, decellularized, the ECM loses its cell supporting mechanical integrity. We report, here, a novel biohybrid vascular graft of polycaprolactone (PCL), poliglecaprone (PGC) incorporated with human biomatrix as functional materials for vascular tissue interfacing by electrospinning, thus harnessing the biochemical cues from the ECM and the mechanical integrity of the polymer blends. The fabricated fibro-porous tubular small diameter graft (i.d. = 4 mm) from polymer blend was coated with a cocktail of collagenous matrix derived from human placenta called HuBiogel™. The compositional, morphological, and mechanical properties of graft were measured and compared with a non-coated tubular PCL/PGC graft using Fourier Transform infrared spectroscopy (FTIR), x-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). BCA assay was used to calculate the protein content and coating-uniformity throughout the hybrid graft. Mechanical properties such as tensile strength (1.6 MPa), Young's modulus (2.4 MPa), burst pressure (>1900 mmHg), and suture retention strength (2.3 N) of hybrid graft were found to be comparable to native blood vessels. Protein coating has improved the hydrophilicity and the biocompatibility (cell viability and cell-attachment) enhanced with human umbilical vein endothelial cells (HUVECs) seeded in vitro onto the lumen layer of the graft over two weeks. The overall results promise this new biohybrid graft to be a potential candidate for vascular tissue interface and regeneration.

Electrospun Nano-Fibers for Biomedical and Tissue Engineering Applications: A Comprehensive Review

Pharmaceutical nano-fibers have attracted widespread attention from researchers for reasons such as adaptability of the electro-spinning process and ease of production. As a flexible method for fabricating nano-fibers, electro-spinning is extensively used. An electro-spinning unit is composed of a pump or syringe, a high voltage current supplier, a metal plate collector and a spinneret. Optimization of the attained nano-fibers is undertaken through manipulation of the variables of the process and formulation, including concentration, viscosity, molecular mass, and physical phenomenon, as well as the environmental parameters including temperature and humidity. The nano-fibers achieved by electro-spinning can be utilized for drug loading. The mixing of two or more medicines can be performed via electro-spinning. Facilitation or inhibition of the burst release of a drug can be achieved by the use of the electro-spinning approach. This potential is anticipated to facilitate progression in applications of drug release modification and tissue engineering (TE). The present review aims to focus on electro-spinning, optimization parameters, pharmacological applications, biological characteristics, and in vivo analyses of the electro-spun nano-fibers. Furthermore, current developments and upcoming investigation directions are outlined for the advancement of electro-spun nano-fibers for TE. Moreover, the possible applications, complications and future developments of these nano-fibers are summarized in detail.

Tissue Engineering and Regenerative Medicine: Achievements, Future, and Sustainability in Asia

Exploring innovative solutions to improve the healthcare of the aging and diseased population continues to be a global challenge. Among a number of strategies toward this goal, tissue engineering and regenerative medicine (TERM) has gradually evolved into a promising approach to meet future needs of patients. TERM has recently received increasing attention in Asia, as evidenced by the markedly increased number of researchers, publications, clinical trials, and translational products. This review aims to give a brief overview of TERM development in Asia over the last decade by highlighting some of the important advances in this field and featuring major achievements of representative research groups. The development of novel biomaterials and enabling technologies, identification of new cell sources, and applications of TERM in various tissues are briefly introduced. Finally, the achievement of TERM in Asia, including important publications, representative discoveries, clinical trials, and examples of commercial products will be introduced. Discussion on current limitations and future directions in this hot topic will also be provided.

Local Delivery of Dual MicroRNAs in Trilayered Electrospun Grafts for Vascular Regeneration

Globally growing problems related to cardiovascular diseases lead to a considerable need for synthetic vascular grafts. For small-caliber vascular prosthesis, it remains essential to fulfill rapid endothelialization, inhibit intimal hyperplasia, and prevent calcification for keeping patency. To modulate vascular regeneration, herein, we developed a bioactive trilayered tissue-engineered vascular graft encapsulating both microRNA-126 and microRNA-145 in the fibrous inner and middle layers, respectively. In vitro cell activities demonstrated that the trilayered electrospun membranes had significant biological advantages in enhanced growth and intracellular nitric oxide production of vascular endothelial cells, modulation of phenotypes of vascular smooth muscle cells (SMCs), and restraint of calcium deposition through fast-releasing microRNA-126 and slow-releasing microRNA-145. Histological and immunofluorescent analyses of in vivo implantation in a rat abdominal aorta interposition model suggested that the dual-microRNA-loading trilayered electrospun graft exerted a positive effect on accelerating endothelialization, improving contractile SMC regeneration, and promoting normal extracellular matrix formation. Meanwhile, the local bioactivity of microRNA-126 and microRNA-145 in the trilayered vascular graft could regulate inflammation and depress calcification possibly by facilitating transformation of macrophages into the anti-inflammatory M2 phenotype. These findings indicated that the trilayered electrospun graft by local delivery of dual microRNAs could be possibly used as a bioactive substitute for replacement of artificial small-caliber blood vessels.

One-Pot Covalent Grafting of Gelatin on Poly(Vinyl Alcohol) Hydrogel to Enhance Endothelialization and Hemocompatibility for Synthetic Vascular Graft Applications

Cardiovascular diseases remain the leading cause of death worldwide. Patency rates of clinically-utilized small diameter synthetic vascular grafts such as Dacron® and expanded polytetrafluoroethylene (ePTFE) to treat cardiovascular disease are inadequate due to lack of endothelialization. Sodium trimetaphosphate (STMP) crosslinked PVA could be potentially employed as blood-compatible small diameter vascular graft for the treatment of cardiovascular disease. However, PVA severely lacks cell adhesion properties, and the efforts to endothelialize STMP-PVA have been insufficient to produce a functioning endothelium. To this end, we developed a one-pot method to conjugate cell-adhesive protein via hydroxyl-to-amine coupling using carbonyldiimidazole by targeting residual hydroxyl groups on crosslinked STMP-PVA hydrogel. Primary human umbilical vascular endothelial cells (HUVECs) demonstrated significantly improved cells adhesion, viability and spreading on modified PVA. Cells formed a confluent endothelial monolayer, and expressed vinculin focal adhesions, cell-cell junction protein zonula occludens 1 (ZO1), and vascular endothelial cadherin (VE-Cadherin). Extensive characterization of the blood-compatibility was performed on modified PVA hydrogel by examining platelet activation, platelet microparticle formation, platelet CD61 and CD62P expression, and thrombin generation, which showed that the modified PVA was blood-compatible. Additionally, grafts were tested under whole, flowing blood without any anticoagulants in a non-human primate, arteriovenous shunt model. No differences were seen in platelet or fibrin accumulation between the modified-PVA, unmodified PVA or clinical, ePTFE controls. This study presents a significant step in the modification of PVA for the development of next generation in situ endothelialized synthetic vascular grafts.

SIS/aligned fibre scaffold designed to meet layered oesophageal tissue complexity and properties

With donor organs not readily available, the need for a tissue-engineered oesophagus remains high, particularly for congenital childhood conditions such as atresia. Previous attempts have not been successful, and challenges remain. Small intestine submucosa (SIS) is an acellular matrix material with good biological properties; however, as is common with these types of materials, they demonstrate poor mechanical properties. In this work, electrospinning was performed to mechanically reinforce tubular SIS with polylactic-co-glycolic acid (PLGA) nanofibres. It was hypothesised that if attachment could be achieved between the two materials, then this would (i) improve the SIS mechanical properties, (ii) facilitate smooth muscle cell alignment to support directional growth of muscle cells and (iii) allow for the delivery of bioactive molecules (VEGF in this instance). Through a relatively simple multistage process, adhesion between the layers was achieved without chemically altering the SIS. It was also found that altering mandrel rotation speed affected the alignment of the PLGA nanofibres. SIS-PLGA scaffolds performed mechanically better than SIS alone; yield stress improvement was 200% and 400% along the longitudinal and circumferential directions, respectively. Smooth muscle cells cultured on the aligned fibres showed resultant unidirectional alignment. In vivo the SIS-PLGA scaffolds demonstrated limited foreign body reaction judged by the type and proportion of immune cells present and lack of fibrous encapsulation. The scaffolds remained intact at 4 weeks in vivo, and good cellular infiltration was observed. The incorporation of VEGF within SIS-PLGA scaffolds increased the blood vessel density of the surrounding tissues, highlighting the possible stimulation of endothelialisation by angiogenic factor delivery. Overall, the designed SIS-PLGA-VEGF hybrid scaffolds might be used as a potential matrix platform for oesophageal tissue engineering. In addition to this, achieving improved attachment between layers of acellular matrix materials and electrospun fibre layers offers the potential utility in other applications. STATEMENT OF SIGNIFICANCE: Because of its multi-layered nature and complex structure, the oesophagus tissue poses several challenges for successful clinical grafting. Therefore, it is promising to utilise tissue engineering strategies to mimic and form structural compartments for its recovery. In this context, we investigated the use of tubular small intestine submucosa (SIS) reinforced with polylactic-co-glycolic acid (PLGA) nanofibres by using electrospinning and also, amongst other parameters, the integrity of the bilayered structure created. This was carried out to facilitate smooth muscle cell alignment, support directional growth of muscle cells and allow the delivery of bioactive molecules (VEGF in this study). We evaluated this approach by using in vitro and in vivo models to determine the efficacy of this new system.

Engineering biological gradients

Biological gradients profoundly influence many cellular activities, such as adhesion, migration, and differentiation, which are the key to biological processes, such as inflammation, remodeling, and tissue regeneration. Thus, engineered structures containing bioinspired gradients can not only support a better understanding of these phenomena, but also guide and improve the current limits of regenerative medicine. In this review, we outline the challenges behind the engineering of devices containing chemical-physical and biomolecular gradients, classifying them according to gradient-making methods and the finalities of the systems. Different manufacturing processes can generate gradients in either in-vitro systems or scaffolds, which are suitable tools for the study of cellular behavior and for regenerative medicine; within these, rapid prototyping techniques may have a huge impact on the controlled production of gradients. The parallel need to develop characterization techniques is addressed, underlining advantages and weaknesses in the analysis of both chemical and physical gradients.

Electrospinning and Electrospun Nanofibers: Methods, Materials, and Applications

Electrospinning is a versatile and viable technique for generating ultrathin fibers. Remarkable progress has been made with regard to the development of electrospinning methods and engineering of electrospun nanofibers to suit or enable various applications. We aim to provide a comprehensive overview of electrospinning, including the principle, methods, materials, and applications. We begin with a brief introduction to the early history of electrospinning, followed by discussion of its principle and typical apparatus. We then discuss its renaissance over the past two decades as a powerful technology for the production of nanofibers with diversified compositions, structures, and properties. Afterward, we discuss the applications of electrospun nanofibers, including their use as "smart" mats, filtration membranes, catalytic supports, energy harvesting/conversion/storage components, and photonic and electronic devices, as well as biomedical scaffolds. We highlight the most relevant and recent advances related to the applications of electrospun nanofibers by focusing on the most representative examples. We also offer perspectives on the challenges, opportunities, and new directions for future development. At the end, we discuss approaches to the scale-up production of electrospun nanofibers and briefly discuss various types of commercial products based on electrospun nanofibers that have found widespread use in our everyday life.

Electrospun polycaprolactone/collagen nanofibers cross-linked with 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide/N-hydroxysuccinimide and genipin facilitate endothelial cell regeneration and may be a promising candidate for vascular scaffolds

Purpose

A promising vascular scaffold must possess satisfying mechanical properties, great hemocompatibility, and favorable tissue regeneration. Combining natural with synthetic materials is a popular method of creating/enhancing such scaffolds. However, the effect of additional modification on the materials requires further exploration.

Materials and methods

We selected polycaprolactone (PCL), which has excellent mechanical properties and biocompatibility and can be combined with collagen. Electrospun fibers created using a PCL/collagen solution were used to fashion mixed nanofibers, while separate syringes of PCL and collagen were used to create separated nanofibers, resulting in different pore sizes. Mixed and separated nanofibers were cross-linked with glutaraldehyde (GA), 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide (EDC), and genipin; hence, we named them as mixed GA, mixed EDC (ME), mixed genipin (MG), separated GA, separated EDC (SE), and separated genipin (SG).

Results

Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction showed that cross-linking did not affect the main functional groups of fibers in all groups. ME, MG, SE, and SG met the requisite mechanical properties, and they also resisted collagenase degradation. In hemocompatibility assays, only ME and MG demonstrated ideal safety. Furthermore, ME and MG presented the greatest cytocompatibility. For vascular scaffolds, rapid endothelialization helps to prevent thrombosis. According to human umbilical vein endothelial cell migration on different nanofibers, ME and MG are also successful in promoting cell migration.

Conclusion

ME and MG may be promising candidates for vascular tissue engineering. The study suggests that collagen cross-linked by EDC/N-hydroxysuccinimide or genipin facilitates endothelial cell regeneration, which could be of great benefit in tissue engineering of vascular scaffolds.

Electrospun gelatin/PCL and collagen/PCL scaffolds for modulating responses of bone marrow endothelial progenitor cells

The determination of potential transplantable substrates and substitution cells for corneal endothelium transplantation may compensate for the shortage of cornea donors. Appropriate biodegradable and biocompatible tissue-engineered substratum with seed cells for endothelial keratoplasty has been increasingly studied. In the present study, electrospun gelatin/polycaprolactone (PCL) and collagen/PCL scaffolds were successfully established. Bone marrow endothelial progenitor cells (BEPCs) were cultured on these scaffolds to determine whether the scaffolds may promote the proliferation of BEPCs as well as maintain stem cell characteristics. Two variations of hybrid scaffolds, collagen/PCL (70% collagen and 30% PCL) and gelatin/PCL (70% gelatin and 30% PCL), were established via electrospinning. Microscopic structure, hydrophilicity and wettability of the two scaffolds were subsequently investigated. BEPCs were separately cultured on the scaffolds and were also seeded on glass slides to establish the control group. Furthermore, cell morphology; adherence, as determined by investigation of F-actin expression levels; proliferation, as determined via Cell Counting Kit-8 assays, Ki-67 staining and bromodeoxyuridine (BrdU) staining; and stem cell markers, as determined by cluster of differentiation (CD)-34 and CD-133 protein expression levels; were investigated. In addition, reverse transcription-quantitative polymerase chain reaction (RT-qPCR) was performed to determine gene expression. The two nanofiber scaffolds were established using electrospun techniques with expected hydrophilicity, wettability and biocompatibility. BEPCs were revealed to spread well on and strongly adhere to the collagen/PCL (70:30) and gelatin/PCL (70:30) scaffolds. Furthermore, Ki-67 and BrdU staining results revealed greater levels of positive dots on the two hybrid scaffolds compared with the control group. CD-34 and CD-133 protein staining demonstrated increased levels of fluorescence intensity on scaffolds compared with the control group. Furthermore, increased expression levels of differentiation markers, such as ATP binding cassette subfamily G member 2, leucine rich repeat containing G protein-coupled receptor 5 and CD166, were detected on both scaffolds. RT-qPCR results demonstrated that the expression of caspase-3, which is associated with apoptosis, was decreased on the two scaffolds compared with in the control group. The expression of inflammatory factors, including interleukin (IL)-1, exhibited a significant decrease on the gelatin/PCL scaffold compared with in the control group; whereas the difference between the expression level of IL-1 exhibited by the collagen/PCL group and the control group were not markedly different. Electrospun collagen/PCL and gelatin/PCL scaffolds exhibited the potential to enhance the adherence and proliferation of BEPCs. BEPCs cultured on the two scaffolds demonstrated increased stem cell characteristics and differentiation potential. Electrospun gelatin/PCL and collagen/PCL scaffolds may represent a promising substratum in tissue-engineered corneal endothelium.