Nitrogen removal via nitrite in a partial nitrification sequencing batch biofilm reactor treating high strength ammonia wastewater and its greenhouse gas emission

The effect of Fenton sludge on anaerobic digestion of papermaking wastewater in an upflow anaerobic sludge blanket reactor

An upflow anaerobic sludge blanket (UASB) reactor was used to investigate the effect of adding Fenton sludge (FS) on the anaerobic digestion of actual papermaking wastewater. The results showed that a one-time addition of 10 g/L FS could sustainably promote the performance of UASB for more than 40 days. The organic matter removal efficiency increased by 15.56%, and the biogas production increased by 24.52%. The proportion of methane in biogas increased by 12.87%. Adding FS increased the capacitance values of sludge extracellular polymeric substances and the electron transfer system activity in reactor increased by 1.76 times. The dehydrogenase activity and coenzyme F420 of the sludge increased by 1.54 and 2.11 times, respectively. Adding FS enriched the iron-reducing bacteria (Thermodesulfobacteriota) and hydrolytic acid-producing bacteria (Chloroflexota and Synergistota), thereby promoting the hydrolysis and acidification process. Adding FS was beneficial to the enrichment of methanogen, especially Methanosaeta, significantly increasing the methane production.

Influence of aeration modes and DO on simultaneous nitrification and denitrification in treatment of hypersaline high-strength nitrogen wastewater using sequencing batch biofilm reactor (SBBR)

Sequencing batch biofilm reactor (SBBR) has the potential to treat hypersaline high-strength nitrogen wastewater by simultaneous nitrification-denitrification (SND). Dissolved oxygen (DO) and aeration modes are major factors affecting pollutant removal. Low DO (0.35-3.5 mg/L) and alternative anoxic/aerobic (A/O) mode are commonly used for municipal wastewater treatment, however, the appropriate DO concentration and operation mode are still unknown under hypersaline environment because of the restricted oxygen transfer in denser extracellular polymeric substances (EPS) barrier and the decreased carbon source consumption during the anoxic phase. Herein, two SBBRs (R1, fully aerobic mode; R2, A/O mode) were used for the treatment of hypersaline high-strength nitrogen wastewater (200 mg/L NH4+-N, COD/N of 3 and 3% salinity). The results showed that the relatively low DO (2 mg/L) could not realize effective nitrification, while high DO (4.5 mg/L) evidently increased nitrification efficiency by enhancing oxygen transfer in denser biofilm that was stimulated by high salinity. A stable SND was reached 16 days faster with a ∼10% increase of TN removal under A/O mode. Mechanism analysis found that denser biofilm with coccus and bacillus were present in A/O mode instead of filamentous microorganisms, with the secretion of more EPS. Corynebacterium and Halomonas were the dominant genera in both SBBRs, and HN-AD process might assist partial nitrification-denitrification (PND) for highly efficient TN removal in biofilm systems. By using the appropriate operation mode and parameters, the average NH4+-N and TN removal efficiency could respectively reach 100% and 70.8% under the NLR of 0.2 kg N·m-3·d-1 (COD/N of 3), which was the highest among the published works using SND-based SBBRs in treatment of saline high-strength ammonia nitrogen (low COD/N) wastewater. This study provided new insights in biofilm under hypersaline stress and provided a solution for the treatment of hypersaline high-strength nitrogen (low COD/N) water.

Combination of partial nitrification and microbial fuel cell for simultaneous ammonia reduction, organic removal, and energy recovery

The chemical oxygen demand (COD) in municipal wastewater has become an obstacle for anammox in mainstream applications. In this study, the single chamber microbial fuel cell (MFC) was installed as an influent device for a partial nitrification-sequencing batch reactor (PN-SBR) to realize integrating COD removal and partial nitrification. After 80 days of operation, the nitrite accumulation rate reached 93%, while the COD removal efficiency was 56%. The output voltage and the power density of MFC were 66.62 mV and 2.40 W/m3, respectively. The content of EPS, especially polysaccharides in the stable phase, has increased compared with the seed sludge. The most dominant genus in MFC anode biofilm and SBR granular sludge was Thauera, which has organic compounds degradation capacity and could degrade nitrate. This study revealed the microbial interaction between MFC and partial nitrification and provided a new strategy for stable ammonia and nitrite supply for mainstream anammox plants.

An enriched ammonia-oxidizing microbiota enables high removal efficiency of ammonia in antibiotic production wastewater

High ammonia concentration hinders the efficient treatment of antibiotic production wastewater (APW). Developing effective ammonia oxidation wastewater treatment strategies is an ideal approach for facilitating APW treatment. Compared with traditional nitrification strategies, the partial nitrification process is more eco-friendly, less energy-intensive, and less excess sludge. The primary limiting factor of the partial nitrification process is increasing ammonia-oxidizing bacteria (AOB) while decreasing nitrite-oxidizing bacteria (NOB). In this study, an efficient AOB microbiota (named AF2) was obtained via enrichment of an aerobic activated sludge (AS0) collected from a pharmaceutical wastewater treatment plant. After a 52-day enrichment of AS0 in 250 mL flasks, the microbiota AE1 with 69.18% Nitrosomonas microorganisms was obtained. Subsequent scaled-up cultivation in a 10 L fermenter led to the AF2 microbiota with 59.22% Nitrosomonas. Low concentration of free ammonia (FA, < 42.01 mg L^-1) had a negligible effect on the activity of AF2, and the nitrite-nitrogen accumulation rate (NAR) of AF2 was 98% when FA concentration was 42.01 mg L^-1. The specific ammonia oxidation rates (SAORs) at 30 °C and 15 °C were 3.64 kg NH₄⁺-N·kg MLVSS^-1·d^-1 and 1.43 kg NH₄⁺-N·kg MLVSS^-1·d^-1 (MLVSS: mixed liquor volatile suspended solids). The SAOR was 0.52 kg NH₄⁺-N·kg MLVSS^-1·d^-1 when the NaCl concentration was increased from 0 to 20 g L^-1, showing that AF2 functioning was stable in a high-level salt environment. The ammonia oxidation performance of AF2 was verified by treating abamectin and lincomycin production wastewater. The NARs of AF2 used for abamectin and lincomycin production wastewater treatment were >90% and the SAORs were 2.39 kg NH₄⁺-N·kg MLVSS^-1·d^-1 and 0.54 kg NH₄⁺-N·kg MLVSS^-1·d^-1, respectively, which was higher than the traditional biological denitrification process. In summary, AF2 was effective for APW treatment via enhanced ammonia removal efficiency, demonstrating great potential for future industrial wastewater treatment.

Effect of hydrodynamics on the transformation of nitrogen in river water by regulating the mass transfer performance of dissolved oxygen in biofilm

Biofilms drive crucial ecosystem processes in rivers. This study provided the basis for overall quantitative calculations about the contribution of biofilms to the nitrogen cycle. At the early stage of biofilm formation, dissolved oxygen (DO) could penetrate the biofilms. As the biofilm grew and the thickness increased, then the mass transfer of DO was restricted. The microaerobic layer firstly appeared in biofilm under the turbulent flow conditions, with the appearance of the microaerobic and anaerobic layer, the nitrification and denitrification reaction could proceed smoothly in biofilm. And the removal efficiency of total nitrogen (TN) increased as the biofilm matured. Under the turbulent flow conditions, mature biofilms had the smallest thickness, but the highest proportion the anaerobic layer to the biofilm thickness, the highest density, and the highest nitrogen removal efficiency. However, the nitrogen removal efficiency of biofilm was the lowest under laminar flow conditions. The difference of layered structure of biofilm and the DO flux in biofilm explained the difference of nitrogen migration and transformation in river water under different hydrodynamic conditions. This study would help control the growth of biofilm and improve the nitrogen removal capacity of biofilm by regulating hydrodynamic conditions.

Nitrification resistance and functional redundancy maintain the system stability of partial nitrification in high-strength ammonium wastewater system

The sudden change of ammonia loading in high-strength ammonium wastewater treatment can directly affect the system stability by altering microbial community dynamics. To maintain the system stability, the effects of ammonia shock loading on microbial community dynamics must be studied. Two sets of sequencing batch reactors were operated with 6 shock cycles (maximum volumetric loading rate of 1928 mg N/(L·d)). CN system contained both organic carbon and ammonia and N system contained only ammonia. Comparing with N system, CN system operated more stably and had higher nitrite accumulation rate. Free ammonia (FA) was the select stress for the turnover of CN microbial communities, while the N communities didn t shift much. The increase of Nitrosomonas and the appearance of heterotrophic nitrification-aerobic denitrification bacteria in CN system presented its resistance and redundancy against FA impact, while the increase of functional genes exhibited functional genes redundancy which maintained the system stability.

Insights into deterioration and reactivation of a mainstream anammox biofilm reactor response to C/N ratio

In-depth knowledge of the deterioration and reactivation of the anaerobic ammonium oxidation (anammox) induced by carbon-to-nitrogen (C/N) is still lacking. Herein, the anammox performance was investigated in an anaerobic sequence biofilm batch reactor fed with low-strength partial nitration effluent in the range of C/N ratio from 0.5 to 3. The anammox was hardly deteriorated at C/N lower than 1.5, while became worsen if C/N was above 2.0. The specific anammox activity (SAA) experiments showed an 85% decrease of SAA at C/N of 3.0 compared with the maximum value (C/N:0). However, anammox capacity was rapidly recovered once influent C/N was adjusted back to zero. Moreover, C/N also highly affected the composition, structure and function of extracellular polymeric substance of the anammox biofilm. High-throughput sequencing revealed a close correlation between C/N change and microbial structure shift. Finally, the potential inhibition and restoration mechanism of the C/N-dependent anammox were proposed based on metagenomic analysis. This research provides some insights into the reinstatement of a mainstream anammox biofilm process after it is interrupted by high C/N influent.

Light-introduced partial nitrification in an algal-bacterial granular sludge bioreactor: Performance evolution and microbial community shift

This objective of study was to evaluate the influence of light on the achievement of partial nitrification algal-bacterial granular bioreactor and its related nitrite accumulation mechanism. After 150-days operation, partial nitrification algal-bacterial granulation bioreactor was achieved under the 200 μmol/(m²·s) illuminance condition. The effluent NH₄⁺-N, NO₂^--N, NO₃^--N concentrations were average at 1.1, 61.7 and 8.0 mg/L (n = 21), respectively. The average sphericity of algal-bacterial aerobic granular sludge (AB-AGS) increased from 82.7% to 91.1%, accompanied by the significantly increased diameter. Additionally, extracellular protein increased by 1.5 times and 0.5 times higher in LB-EPS and TB-EPS of AB-AGS, respectively. According to typical cycles, N₂O emission amount reactor accounted for 2.4% of the removed nitrogen. Under the combined inhibition of light and free ammonia (FA), Nitrosomonas-related AOB (0.2% to 2.1%) were the predominant functional bacteria, whereas Nitrospira-related NOB (0.07% to below 0.01%) was fully inhibited.

Rapidly achieving partial nitrification of municipal wastewater in enhanced biological phosphorus removal (EBPR) reactor: Effect of heterotrophs proliferation and microbial interactions

Stable nitritation is the major challenge for short-cut nitrogen removal from municipal wastewater. This paper demonstrated a rapid achievement of partial nitrification (PN) in an enhanced biological phosphorus removal (EBPR) reactor treating domestic wastewater. Polyphosphate accumulating organisms (PAOs) were enriched operated at a short aerobic HRT (2.0 h) and SRT (10 d), with satisfactory phosphorus removal efficiency (95.9%). Both of ammonia oxidizing bacteria (AOB) and nitrite oxidizing bacteria (NOB) were elutriated simultaneously. Interestingly, AOB recovered much faster than NOB by a subsequent extension of aerobic HRT and SRT, resulting in a rapid development of PN within 15 days. Ammonia oxidation rates of AOB significantly increased by 44.2%, facilitating a high nitrite accumulation rate (NAR) of 95.8%. Genus Tetrasphaera, Halomonas, Paracoccus and Candidatus_Accumulibacter belonging to PAOs accounted for 4.6%. The proliferation of heterotrophs, typically as PAOs, maximized the microbial competition against NOB by favoring AOB activity and synergy with functional bacteria.

Calcium modified basalt fiber bio-carrier for wastewater treatment: Investigation on bacterial community and nitrogen removal enhancement of bio-nest

Modified basalt fiber (MBF) is a sustainable material studied as novel wastewater treatment bio-carrier recently. This work studied the effects of calcium modification on the bacterial affinity of modified fiber (Ca-MBF), bacterial community, and nitrogen removal performance. Results showed that Ca-MBF with hydrophilic (62.66°) and positively-charged (7.80 mV) surface accelerated bacterial attachment. Volatile suspended solids on Ca-MBF (5.46 g VSS/g fiber) were increased by 2.61 times after modification, with high bacterial activity when bio-carriers were cultured in activated sludge. Extracellular polymeric substances on Ca-MBF was 4.35 times higher and consisted of more protein. Bio-nests with unique aerobic/anaerobic structure formed on the ultrafine carriers in bioreactor. Ca-MBF bioreactor exhibited total nitrogen removal efficiency above 72.2% and COD removal efficiency above 94.2% with more stable performance than unmodified carrier in long-term treatment using synthetic domestic wastewater.16S rRNA gene sequencing revealed enhanced abundance of nitrifying and denitrifying bacteria in Ca-MBF bio-nest.

Performance and mechanism of a novel woodchip embedded biofilm electrochemical reactor (WBER) for nitrate-contaminated wastewater treatment

In this study, a woodchip biofilm electrode reactor (WBER) with woodchips embedded anode and cathode was developed, and its denitrification mechanism was analyzed by investigating the denitrification performance, organic matter change, redox environment and microbial community. The results show that the WBER with a carbon rod as anode (C-WBER) had a higher denitrification efficiency (2.58 mg NO- 3-N/(L·h)) and lower energy consumption (0.012 kWh/g NO- 3-N) at 350 mA/m². By reducing the hydroxyl radical and dissolved oxygen concentrations, anode embedding technology effectively decreased the inhibition on microorganisms. Lignin decomposition, nitrification and aerobic denitrification were carried out in anode. Additionally, hydrogen autotrophic denitrification and heterotrophic denitrification were occurred in cathode. The WBER effectively removed nitrate and reduced the cost, providing a theoretical basis and direction for further develop BERs.

Spectroscopic investigation of the interaction between extracellular polymeric substances and tetracycline during sorption onto anaerobic ammonium-oxidising sludge

In this study, the interaction between extracellular polymeric substances (EPS) and tetracycline during sorption onto anaerobic ammonium-oxidising (anammox) sludge was investigated. The results showed that EPS significantly enhanced the adsorption efficiency of tetracycline by sludge, and the adsorption data were better fitted with the pseudo-second-order kinetics model. Further, the concentration of proteins in the EPS decreased from 12.31 ± 0.42 to 6.82 ± 0.46 mg/gVSS for various tetracycline dosages (0-20 mg/L), whereas the concentration of polysaccharides did not change. Multiple spectroscopic methods were used to analyze the interaction between EPS and tetracycline. A three-dimensional excitation-emission matrix revealed that the fluorescence intensity of protein-like substances obviously decreased with the increasing addition of tetracycline. According to synchronous fluorescence spectra analysis, static quenching was the major quenching process and there was one type of binding site in the protein-like substances. Additionally, two-dimensional correlation spectroscopy showed that tryptophan-like aromatic protein was more susceptible to tetracycline binding than tyrosine-like aromatic protein. Moreover, the main functional groups involved in complexation of tetracycline and EPS were C-O, C-C and C-N (stretching vibration) and the pyrrole ring of the tryptophan side chain. This study provides useful information on the interaction between EPS and tetracycline and demonstrates the role of EPS in protecting microorganism from tetracycline in the anammox process.

Immobilization of nitrifying bacteria on composite based on polymers and eggshells for nitrate production

Nitrification is a key step in biological nitrogen transformation which depends on the performance of specialized microorganisms. Generally, nitrifying bacteria present a low growth rate and performance which can be improved when immobilized as a biofilm. The development of new materials suitable for the immobilization of nitrifying microorganisms is very important in nitrification and wastewater treatment. In this study, the effect of eggshell powder on biofilm formation by Nitrosomonas europaea an ammonium-oxidizing bacteria and Nitrobacter vulgaris a nitrite-oxidizing bacteria, on new polymeric supports were analyzed. Polylactic acid, polyvinyl chloride and polystyrene were tested to produce polymer-eggshells powder composites and used as biofilm supports for nitrifying bacteria. The support material was characterized to identify the most suitable polymer-eggshells powder combination for the cell adhesion and biofilm formation. The nitrification results showed a highest nitrate production of 42 mg NO₃^--N/L with polylactic acid-eggshell composite, with the best surface properties for cellular adhesion. Finally, scanning electron microscopy micrographs confirmed the best biofilm formed on polylactic acid-eggshell.

Enhanced simultaneous nitrogen and phosphorus removal from low COD/TIN domestic wastewater through nitritation-denitritation coupling improved anammox process with an optimal Anaerobic/Oxic/Anoxic strategy

Advanced nitrogen and phosphorus removal in a single-stage suspending-sludge system was achieved by employing a novel Anaerobic/Oxic/Anoxic (AOA) strategy over 200 days. Satisfactory total inorganic nitrogen (TIN) removal efficiency of 90.4% was achieved and effluent phosphorus was below 0.5 mg/L when treating domestic wastewater with the chemical oxygen demand (COD)/TIN as low as 2.98 ± 1.26. Stable nitritation was maintained with the ammonia residual and low dissolved oxygen of 0.2-0.5 mg/L at aerobic stage following by a post anoxic stage. The much higher activity of ammonia oxidation bacteria (12.99 mgN/gVSS/h) was achieved than the nitrite oxidation bacteria (0.09 mgN/gVSS/h). Notably, improved anammox performance was obtained without initial inoculation, contributing 47.4% to TIN removal. The abundance of Nitrosomonas increased from 0.12% to 0.95% (P < 0.001) and self-enrichment of anammox bacteria Ca. Brocadia was confirmed. It provided new insight into the advanced nutrient removal with comprehensible regulation and less aeration requirement.

Effect of magnetic powder on nitrous oxide emissions from a sequencing batch reactor for treating domestic wastewater at low temperatures

Low temperatures can lead to an increase of N₂O generation and emission from the nitrogen removal process in wastewater treatment plants. This study investigated the effect of the addition of magnetic powder on N₂O generation and emission from a sequencing batch reactor treating domestic sewage at low temperatures. The results showed that the magnetic powder simultaneously inhibited N₂O generation and emission and improved the removal of NH₄⁺, total nitrogen (TN), and chemical oxygen demand at low temperatures. Furthermore, the conversion rate of N₂O (N₂O generation to TN removal) was reduced. The efficacy of the magnetic powder depended on its concentration, which could be ordered as 1 mg/L > 2 mg/L > 4 mg/L. With the addition of magnetic powder, especially at the 1 mg/L level, the activities of nitrification and denitrification enzymes in activated sludge were significantly improved and the growth of ammonium and nitrite oxidizing bacteria was also promoted.

Analysis of the Partial Nitrification Process Affected by Polyvinylchloride Microplastics in Treating High-Ammonia Anaerobic Digestates

Large amounts of microplastics entering into wastewater treatment plants are retained as wasted sludges, which are usually transferred to the anaerobic digestion process afterward. The partial nitrification (PN) process is known for treating the high ammonia anaerobic digestate; its treatment performance that is affected by the existence of microplastics is rarely reported. This study investigated the effect of microplastics on the PN process with polyvinylchloride (PVC) abundances at 0, 1000, 5000, and 10,000 particles/L. Results indicated that the corresponding nitrite transfer rates with the existence of PVC were 90.97, 64.24, 52.88, and 46.66%. The ammonia oxidation rate was reduced to 0.69, 0.55, and 0.49 times as compared with control. The average dissolved nitrous oxide (N₂O) emission was also mitigated to 0.58, 0.49, and 0.64 times with added microplastics as compared with control. The average gaseous form of N₂O emitted was mitigated to 0.54, 0.45, and 0.37 times as compared with control. The first-order kinetic model fitted well with all tests. The highest NO₂-N generation potential was found in the blank reactor at a coefficient of 1430.1 (R ² = 0.9776), which was 1.9-2.3 times higher than the other reactors with added microplastics. This study indicated that PVC inhibited the PN process and mitigated N₂O emission during such a process. The microplastic contamination effects on high-ammonia wastewater treatment during the PN process must be considered for investigation.

New progress of ammonia recovery during ammonia nitrogen removal from various wastewaters

The recovery of ammonia-nitrogen during wastewater treatment and water purification is increasingly critical in energy and economic development. The concentration of ammonia-nitrogen in wastewater is different depending on the type of wastewater, making it challenging to select ammonia-nitrogen recovery technology. Meanwhile, the conventional nitrogen removal method wastes ammonia-nitrogen resources. Based on the circular economy, this review comprehensively introduces the characteristics of several main ammonia-nitrogen source wastewater plants and their respective challenges in treatment, including municipal wastewater, industrial wastewater, livestock and poultry wastewater and landfill leachate. Furthermore, we introduce the main methods currently adopted in the ammonia-nitrogen removal process of wastewater from physical (air stripping, ion exchange and adsorption, membrane and capacitive deionization), chemical (chlorination, struvite precipitation, electrochemical oxidation and photocatalysis) and biological (classical and typical activated sludge, novel methods based on activated sludge, microalgae and photosynthetic bacteria) classification based on the ammonia recovery concept. We discuss the applicable methods of recovering ammonia nitrogen in several main wastewater plants. Finally, we prospect the research direction of ammonia removal and recovery in wastewater based on sustainable development.

Start-up of single-stage partial nitritation-anammox micro-granules system: Performance and microbial community dynamics

By manipulating influent nitrogen load and DO concentration in bulk liquid, the start-up and performance of a new micro-granule based partial nitritation-anammox process was investigated in a continuous stirred tank reactor (CSTR). Under the condition of nitrogen loadings from 0.3 to 1.4 kgN /m³/d and DO <0.21mg/L, the single-stage partial nitritation-anammox (SPNA) system was successfully started, with a nitrogen removal of 76.2%. Meanwhile, the oxygen utilization efficiency by ammonium oxidizing bacteria (AOB) increased in the system with the increase of influent ammonia loading rate. Micro-granules with an average diameter of 0.25 mm were formed. Sludge granulation was promoted by increasing influent nitrogen load, and there was a positive correlation between nitrogen load, extracellular polymeric substances (EPS) content and sludge particle size. Ca. Kuenenia became the dominant anaerobic ammonium oxidizing bacteria (AnAOB) in the SPNA system. As the dominant AOB genera, Nitrosomonas coexist with Ca. Kuenenia in the micro-granules.

Enhanced shortcut nitrogen removal and metagenomic analysis of functional microbial communities in a double sludge system treating ammonium-rich wastewater

Biological nitrogen removal processes based on partial nitrification are promising for ammonium-rich wastewater treatment. In this study, a partial nitrification-denitrification double sludge system was applied to treat synthetic ammonium-rich wastewater. Metagenomic analysis of functional genes and metabolic pathways was conducted, also with the evaluation of system performance and nitrous oxide (N₂O) emission. In the nitrifying sequencing batch reactor (SBR_PN), the removal percentage of ammonium nitrogen reached to 99.98% with a high nitritation efficiency of 93.24%, and the N₂O emission factor was 0.88%. In the denitrifying sequencing batch reactor (SBR_DN), there was almost no nitrate nitrogen and nitrite nitrogen in the effluent, and the maximum N₂O emission was 0.078 mg N/L. The dominant ammonia oxidizing bacteria was Nitrosomonas in SBR_PN (13.6%), and the main potential denitrifiers in SBR_DN were Thauera (14.6%), an uncultured genus in the Comamonadaceae family (4.0%), an uncultured genus in Rhodocyclaceae family (2.4%) and Comamonas (1.1%). Metagenomic analysis revealed that amo mainly distributed in Nitrosomonas eutropha (38.3%), Nitrosomonas europaea (27.1%), Nitrosomonas sp. GH22 (20.5%) and Nitrosomonas sp. TK794 (15.0%), and Bacteroidetes had the N₂O reduction potential in SBR_PN.

Study on the removal of high contents of ammonium from piggery wastewater by clinoptilolite and the corresponding mechanisms

In this study, a clinoptilolite was applied to remove ammonium from piggery wastewater. The performance of ammonium removal and the correspondingly mechanisms were discussed. Under the optimal conditions of clinoptilolite dosage of 12 g/L, solution pH value of 8.3, shaking speed of 280 rpm and contact time of 55 min obtained by using response surface methodology (RSM), 19.7 mg of ammonium can be adsorbed onto 1 g of clinoptilolite, which was declined when metal cations were presented in the piggery wastewater. The ammonium adsorption process by the clinoptilolite can be well fitted by Langmuir isotherm with a spontaneous nature and pseudo–second–order kinetics model. Furthermore, column study showed that to some extent, the increased flow rate was beneficial to the removal of ammonium, and the ammonium adsorption capacity of clinoptilolite in column study was much higher than those in batch study.

Metal oxyanion removal from wastewater using manganese-oxidizing aerobic granular sludge

As, Sb, and Cr are redox-sensitive and toxic heavy metal(loid)s, and redox reactions are usually involved in the treatment of substrates containing these elements. In this study, manganese-oxidizing aerobic granular sludge (Mn-AGS) was obtained by continuously adding Mn(II) to the sludge in a sequencing batch reactor (SBR). Morphological observations, and analyses of extracellular polymeric substances (EPS), Mn valence-states, and microbial communities were performed on the resulting sludge. After 50 days of cultivation, biogenic Mn(III,IV) oxides (bio-MnO_x) accumulated up to approximately 25 mg Mn/g suspended solids (SS). X-ray photoelectron spectroscopy (XPS) revealed that the percentage of Mn(III,IV) was 87.6%. The protein (PN) component in EPS increased from 80.3 to 87.8 mg/g volatile suspended solids (VSS) during cultivation, which might be favorable for sludge granulation and heavy metal(loid) removal. Batch experiments showed that Mn-AGS was better at oxidizing As(III)/Sb(III) into less toxic As(V)/Sb(V) than traditional AGS. Remarkably, the results indicated that Mn-AGS did not oxidize Cr(III) but was able to reduce Cr(VI) into relatively harmless Cr(III). This work provided a new promising method with which to treat As(III), Sb(III), and Cr(VI) in wastewaters.

Insights into the effects of carbon source on sequencing batch reactors: Performance, quorum sensing and microbial community

Effects of carbon source on the performance, quorum sensing (QS) and microbial communities in the sequencing batch reactors were investigated in this work. Among the chosen carbon source, sodium acetate (R1), glucose (R2), starch (R3) and Tween 80 (R4), sodium acetate was the best carbon source for nutrient removal, while starch was favorable for inducing the sludge bulking, and Tween 80 was beneficial to the production of extracellular polymeric substances (EPS) and proliferation of Microthrix parvicella. Additionally, the R² value of linear correlation between sludge settleability and particle size in four reactors followed an order of R1 > R2 > R3 > R4. Moreover, Person correlation analysis showed that various significant correlations were observed in reactors fed with different carbon sources and the QS mainly mediated the production and component of EPS. High-throughput sequencing analysis revealed that the carbon source affected microbial communities and the Canonical correspondence analysis results indicated that QS related to microbial communities. It was inferred that the interactions between microbial communities and QS affected system performance.

Identification and nitrogen removal characteristics of Thauera sp. FDN-01 and application in sequencing batch biofilm reactor

A strain FDN-01 was isolated from the sequencing batch biofilm reactor (SBBR) which was seeded with wasted activated sludge from a municipal wastewater treatment plant in Shanghai. Bacterium FDN-01 was identified as Thauera sp., and Genbank Sequence_ID was KY393097. By comparing inorganic total nitrogen (TN) removal efficiency by strain FDN-01 under different conditions, the optimal initial pH, carbon source and the ratio of carbon to nitrogen were 7.5, sodium succinate and 4.0, respectively. Inorganic TN removal efficiency was 93% within 3 d while the concentration of nitrate was 100 mg/L, and the type of substrates affected extracellular polymeric substances (EPS) production and the ratio of protein to polysaccharide in the EPS. Further investigation for the application of strain FDN-01 in the SBBRs showed that anoxic ammonia oxidation occurred at room temperature, and the removal efficiencies of inorganic TN were noticeably enhanced by the augmentation of bacterium FDN-01 back into the SBBR. This study provided a promising method of TN removal requiring less carbon source in the wastewater.

Evaluation of modified basalt fiber as biological carrier media for wastewater treatment with the extended DLVO theory model

In this study, environment-friendly inorganic basalt fiber (BF) was used as bio-carrier for wastewater treatment. To enhance the bio-affinity, raw BF was modified by grafting the diethylamino functional groups to make the surface more hydrophilic and electro-positive. Contact angle and zeta potential of modified basalt fiber (MBF) were characterized. The capacity of MBF bio-carriers was evaluated by microorganism immobilization tests. To explain the mechanism of capacity enhancement by modification, the profiles of total interaction energy barrier between raw BF (or MBF) and bacteria (Escherichia coli, E. coli) were discussed based on the extended Derjaguin-Landau-Verwey-Overbeek (DLVO) theory. The results showed the contact angle of fiber decreased from 89.71° to 63.08° after modification, and zeta potential increased from - 18.53 to +10.58 mV. The microorganism immobilization tests showed that the surface modification accelerated the initial bacterial adhesion on fiber. The total interaction energy barrier between MBF and E. coli disappeared as a result of electrostatic and hydrophilic attractive forces, and enhanced the irreversible adhesion. MBF bio-carrier medium provides a promising alternative to conventional bio-carrier materials for wastewater treatment. Graphical abstract.

Mechanistic understanding of the NOB suppression by free ammonia inhibition in continuous flow aerobic granulation bioreactors

A partial nitritation continuous flow reactor (CFR) was operated for eight months demonstrating that partial nitritation granular sludge can remain stable under continuous flow conditions. The ammonia oxidizing bacteria (AOB)-to-nitrite oxidizing bacteria (NOB) activity ratios were determined for a series of granule sizes to understand the impact of mass diffusion limitation on the free ammonia (FA) inhibition of NOB. When dissolved oxygen (DO) limitation is the only mechanism for NOB suppression, the AOB:NOB ratio was usually found to increase with the granule size. However, the trend is reversed when FA has an inhibitory effect on NOB, as was observed in this study. The decrease in AOB:NOB ratio indicates that smaller granules, e.g. diameter <150 μm, are preferred for nitrite accumulation when high FA concentration is present, as in the partial nitritation process. The trend was further verified by observing the increase in the apparent inhibition coefficient as granule size increased. Indeed, this study for the first time quantified the effect of diffusion limitation on the apparent inhibition coefficient of NOB in aerobic granules. A mathematical model was then utilized to interpret the observed suppression of NOB and predicted that NOB suppression was only complete at the granule surface. The NOB that did survive in larger granules was forced to dwell within the granule interior, where the AOB growth declines due to DO diffusion limitation. This means FA inhibition can be taken advantage of as an effective means for NOB suppression in small granules or thin biofilms. Further, both FA inhibition and DO limitation were found to be required for the suppression of NOB in mainstream aerobic granules.

Recycled corrugated wire hose cover as biological carriers for greywater treatment in a sequential batch biofilm reactor

Greywater treatment and reuse can be considered a promising option, in particular in water scarcity affected areas. In this work a waste material, namely recycled corrugated wire hose cover, was applied as an alternative and cheap carrier in a sequencing batch biofilm reactor (SBBR) for greywater treatment. The bioreactor performance was studied in terms of organic matter, nitrogen and micropollutant removal. Four operational stages were investigated: i) inoculation of the carriers; ii) greywater treatment with suspended biomass; iii) synthetic and iv) real greywater treatment with inoculated carriers in the SBBR. The SBBR could treat real greywater showing high removal efficiencies for COD (86.5 ± 5.8%), ammonium (98.4 ± 1.4%) and total nitrogen (71.4 ± 8.2%). The obtained efficiencies were similar to the ones obtained with commercial carriers and to other treatments such as MBBR or MBR. In terms of micropollutants, 7 out of 13 detected micropollutants were highly removed (efficiency higher than 85%) while 5 of them (ofloxacin, metoprolol acid, venlafaxine, iopromide and hydrochlorothiazide) were found to be highly recalcitrant to the treatment.

The alleviative effect of exogenous phytohormones on the growth, physiology and gene expression of Tetraselmis cordiformis under high ammonia-nitrogen stress

In this study, the toxic effect of high ammonia on microalgae Tetraselmis cordiformis and the detoxification of phytohormones were researched. The growth, physiological changes, and gene transcription of T. cordiformis were examined. Malondialdehyde content was increased by 2.12 times compared with the control, suggesting the oxidative damage of T. cordiformis. However, the damaging effect of ammonia stress was significantly alleviated by exogenous phytohormones revealed by photosynthetic activity, antioxidant capacity, and nitrogen metabolism. Compared with cells exposed to 500 mg L^-1 ammonia (NH₄⁺-N), phytohormones increased the transcript abundance of photosynthesis-related gene (rbcL) by up to 10.95 times. Besides, after adding phytohormones, maximum activities of the antioxidant enzyme catalase (CAT) and nitrogen metabolism-related enzyme glutamine synthetase (GS) were 2.17 and 6.72 times that of the cells exposed to 500 mg L^-1 NH₄⁺-N. This study displayed the toxic mechanism of high ammonia on T. cordiformis, and also proved the detoxification of phytohormones.

Adsorption characteristics of nitrite on natural filter medium: Kinetic, equilibrium, and site energy distribution studies

Nitrite is one of the world's major contaminants in drinking water resources, and granular anthracite is often used as filter medium in water treatment. In this study, the adsorption characteristics of nitrite on granular anthracite under various temperatures were investigated through adsorption kinetic, isotherm models, and site energy distribution theory. The adsorption of nitrite on granular anthracite was an endothermic reaction, while intraparticle diffusion was not the only rate control step. The adsorption could be well described by using pseudo-second-order and Langmuir-Freundlich equations. The adsorption capacity was 402.51 mg NO₂^--N kg^-1 at 298 K, which could be significantly improved to 1380.1 mg NO₂^--N kg^-1 when the temperature reached 308 K. Furthermore, nitrite ions first occupied the high-energy adsorption sites and then diffused to the low-energy adsorption sites on granular anthracite. There were more sites, including high-energy sites and low-energy sites, for nitrite adsorption at 308 K. Besides, the thickness of the boundary layer increased with the adsorption capacity improved at a higher temperature, and nitrite ions were adsorbed mainly through chemical mechanisms. Moreover, the neutral pH was helpful for the adsorption. The presence of co-existing ions could limit the adsorption and the effect followed the order of PO₄^3- > CO₃^2- > SO₄^2- > NO₃^- > Cl^-. The saturated anthracite could be effectively regenerated by 0.2 mol L^-1 HCl solution. Therefore, the granular anthracite used as filter medium also has a possible application as a nitrite scavenger at the same time.

System performance and microbial community succession in a partial nitrification biofilm reactor in response to salinity stress

The system performance and microbial community succession in a partial nitrification biofilm reactor in response to salinity stress was conducted. It was found that the NH₄⁺-N removal efficiency decreased from 98.4% to 42.0% after salinity stress increased to 20 g/L. Specific oxygen uptake rates suggested that AOB activity was more sensitive to the stress of salinity than that of NOB. Protein and polysaccharides contents showed an increasing tendency in both LB-EPS and TB-EPS after the salinity exposure. Moreover, EEM results indicated that protein-like substances were the main component in LB-EPS and TB-EPS as self-protection in response to salinity stress. Additionally, humic acid-like substances were identified as the main component in the effluent organic matter (EfOM) of partial nitrification biofilm, whereas fulvic acid-like substances were detected at 20 g/L salinity stress. Microbial community analysis found that Nitrosomonas as representative species of AOB were significantly inhibited under high salinity condition.

Characterization of soluble microbial products in a partial nitrification sequencing batch biofilm reactor treating high ammonia nitrogen wastewater

In present study, the characterization of soluble microbial products (SMP) was evaluated in a partial nitrification sequencing batch biofilm reactor (SBBR). During the stable operation of SBBR, the NH₄⁺-N removal efficiency and nitrite accumulation ratio were 96.70±0.41% and 93.77±1.04%, respectively. According to excitation-emission matrix (EEM), the intensities of protein-like substances were reduced under anoxic and aerobic phases, whereas humic-like substances had little change during the whole cycle. Parallel factor analysis (PARAFAC) further indentified two components and their fluorescence intensity scores were both reduced. Synchronous fluorescence spectra revealed that the fluorescence intensity of protein-like fraction decreased with reaction time. Two-dimensional correlation spectroscopy (2D-COS) further demonstrated that protein-like fraction might decrease earlier than the other fractions. The information obtained in present study is of fundamental significance for understanding the key components in SMP and their changes in partial nitrification system by using a spectral approach.

Characterization of EPS compositions and microbial community in an Anammox SBBR system treating landfill leachate

The biofilm system is beneficial for Anammox process designed to treat landfill leachate. In this study, the composition of extracellular polymeric substances (EPS) and the microbial community in an Anammox biofilm system were analyzed to determine the functions driving the biofilm's ability to treat landfill leachate. The results demonstrated that increasing influent carbon oxygen demand (COD) could stimulate EPS production. EPS helped enrich Anammox bacteria and supplied them with nutrients and enzymes, facilitating effective nitrogen removal (approximately 95%). The variation in Anammox bacteria was similar to the variation in EPS composition. In the tested Anammox Sequencing Biofilm Batch Reactor (SBBR) system, Candidatus Kuenenia was dominant among known Anammox genus, because of its high substrate affinity and because it adapts better to landfill leachate. The relative abundance of Candidatus Kuenenia in the biofilm rose from 3.26% to 12.38%, illustrating the protection and enrichment offered by the biofilm in carrying out Anammox.

Combined SHARON and ANAMMOX processes for ammoniacal nitrogen stabilisation in landfill bioreactors

Stabilisation of ammoniacal nitrogen from solid waste and leachate significantly improved by combining novel processes like SHARON (single reactor system for high activity ammonia removal over nitrite) and ANAMMOX (anaerobic ammonium oxidation) with advantages of lower carbon requirements, aeration and N₂O emissions. This paper deals with establishing combined SHARON-ANAMMOX processes in situ pilot-scale landfill bioreactors (LFBR). Molecular analysis in LFBR with changes in nitrogen, hydrazine, hydroxylamine confirmed aerobic and anaerobic ammonium oxidising bacteria (AOB & ANAMMOX) as key players in SHARON-ANAMMOX processes. In situ SHARON-ANAMMOX process was established in LFBR with total nitrogen and ammoniacal nitrogen removal efficiency of 84% and 71%, respectively at NLR of 1.2 kgN/m³/d in 147 d, compared to ammoniacal nitrogen removal of 49% at NLR of 1.0 kgNH₄-N/m³/d in 336 d feasible in Control LFBR. Nitrogen massbalance demonstrated in situ SHARON-ANAMMOX advantageous than control LFBR with higher nitrogen transformation to N₂ (50.8%) and lower residual nitrogen in solid waste (7.7%).

Ammonium removal in landfill leachate using SBR technology: dispersed versus attached biomass

Large concentrations and oscillations of ammonium nitrogen (NH₄⁺-N) in municipal landfill leachate pose considerable constraints to its further treatment in central wastewater treatment plants. The aim of this study was to evaluate and optimize two technologies for the pre-treatment of 600 L/day of landfill leachate: in particular, to optimize their operational conditions for NH₄⁺-N removal up to a level appropriate for discharge to sewers, i.e. <200 mg/L. Both technologies were based on a sequencing batch reactor (SBR), with two different biomass processes: (A) SBR with dispersed/flocculated biomass and (B) SBR with biomass attached to carriers. The results revealed that both technologies successfully reduced the NH₄⁺-N from 666 mg/L (on average) at the inflow to below 10 mg/L at the outflow with alkalinity adjustment in a 12-hour cycle. Both technologies achieved 96% removal efficiencies for NH₄⁺-N. However, SBR with dispersed biomass showed higher flexibility under varying conditions due to the shorter adaptation time of the biomass.

Effect of influent C/N ratio on N2O emissions from anaerobic/anoxic/oxic biological nitrogen removal processes

The problem of producing strong greenhouse gas of nitrous oxide (N₂O) from biological nitrogen removal (BNR) process in wastewater treatment plants (WWTP) has elicited great concern from various sectors. In this study, three laboratory-scale wastewater treatment systems, with influent C/N ratios of 3.4, 5.4, and 7.5, were set up to study the effect of influent C/N ratio on N₂O generation in anaerobic/anoxic/oxic (A²O) process. Results showed, with the increased influent C/N ratio, N₂O generation from both nitrification and denitrification process was decreased, and the N₂O-N conversion ratio of the process was obviously reduced from 2.23 to 0.05%. Nitrification rate in oxic section was reduced, while denitrification rate in anaerobic and anoxic section was elevated and the removal efficiency of COD, NH₄⁺-N, TN, and TP was enhanced in different extent. As the C/N ratio increased from 3.4 to 7.5, activities of three key denitrifying enzymes of nitrate reductase, nitrite reductase, and nitrous oxide reductase were increased. Moreover, microorganism analysis indicated that the relative abundance of ammonium-oxidizing bacteria (AOB) and nitrite-oxidizing bacteria (NOB) were positively correlated with N₂O generation, which was reduced from (8.42 ± 3.65) to (3.61 ± 1.66)% and (10.38 ± 4.12) to (4.67 ± 1.62)%, respectively. NosZ gene copy numbers of the A²O system were increased from (1.19 ± 0.49) × 10⁷ to (2.84 ± 0.54) × 10⁸ copies/g MLSS with the influent C/N ratio elevated from 3.4 to 7.5. Hence, appropriate influent C/N condition of A²O process could optimize the microbial community structure that simultaneously improve treatment efficiency and decrease the N₂O generation.

Achievement, performance and characteristics of microbial products in a partial nitrification sequencing batch reactor as a pretreatment for anaerobic ammonium oxidation

This study was carried out to evaluate achievement, performance and characteristics of microbial products in a partial nitrification sequencing batch reactor as a pretreatment for anaerobic ammonium oxidation (anammox). After 100 days long-term operation, the effluent NO₂^--N/NH₄⁺N ratio of the reactor was average at 1.3 and NO₃^--N concentration was low by controlling low dissolved oxygen (DO) concentration, which was considered as the ideal influent for anammox. Specific oxygen uptake rate (SOUR) implied that (SOUR)_NH4 and (SOUR)_NO2 of ammonia oxidizing bacteria (AOB) and nitrite oxidizing bacteria (NOB) in sludge changed from 21.73 ± 0.52 and 27.39 ± 0.50 O₂/g SS/h to 36.37 ± 0.85 and 12.04 ± 0.17 O₂/g SS/h, respectively. The main compositions of extracellular polymeric substances (EPS) and soluble microbial products (SMP), including proteins (PN) and polysaccharides (PS), were both reduced during the achievement of partial nitrification. Three-dimensional excitation-emission matrix (3D-EEM) and synchronous fluorescence spectra revealed that PN-like, fulvic acid-like and humic acid-like substances were identified in both EPS and SMP, and their fluorescence intensities changed significantly after partial nitrification achievement. It was found from typical cycle that free ammonia (FA) may play a significant role on inhibiting the activity of NOB. The obtained results could provide more information on the performance of partial nitrification through the characteristics of microbial products when treating high ammonium wastewater.