Microalgae biomass from swine wastewater and its conversion to bioenergy

Mini critical review: Membrane fouling control in membrane bioreactors by microalgae

Membrane bioreactors (MBRs) hold significant promise for wastewater treatment, yet the persistent challenge of membrane fouling impedes their practical application. One promising solution lies in the synergy between microalgae and bacteria, offering efficient nutrient removal, reduced energy consumption, and potential mitigation of extracellular polymeric substances (EPS) concentrations. Inoculating microalgae presents a promising avenue to address membrane fouling in MBRs. This review marks the first exploration of utilizing microalgae for membrane fouling control in MBR systems. The review begins with a comprehensive overview of the evolution and distinctive traits of microalgae-MBRs. It goes further insight into the performance and underlying mechanisms facilitating the reduction of membrane fouling through microalgae intervention. Moreover, the review not only identifies the challenges inherent in employing microalgae for membrane fouling control in MBRs but also illuminates prospective pathways for future advancement in this burgeoning field.

Carbon flow, energy metabolic intensity and metagenomic characteristics of a Fe (III)-enhanced anerobic digestion system during treating swine wastewater

Deep treatment and bioenergy recovery of swine wastewater (SW) are beneficial for constructing a low-carbon footprint and resource-recycling society. In this study, Fe (III) addition from 0 to 600 mg/L significantly increased the methane (CH4) content of the recovered biogas from 61.4 ± 2.0 to 89.3 ± 2.0 % during SW treatment in an anaerobic membrane digestion system. The specific methane yields (SMY) also increased significantly from 0.20 ± 0.05 to 0.29 ± 0.02 L/g COD. Fe (III) and its bio-transformed products which participated in establishing direct interspecific electron transfer (DIET), upregulated the abundance of e-pili and Nicotinamide adenine dinucleotide (NADH), enriched electroactive bacteria. The increase in cellular adenosine triphosphate (cATP) from 6583 to 14,518 ng/gVSS and electron transport system (ETS) from 1468 to 1968 mg/(g·h) promoted the intensity of energy flow and electron flow during anaerobic digestion of SW. Moreover, Fe (III) promoted the hydrolysis and acidification of organic matters, and strengthened the acetoacetic methanogenesis pathway. This study established an approach for harvesting high quality bioenergy from SW and revealed the effects and mechanisms from the view of carbon flow, energy metabolic intensity and metagenomics.

Pilot-scale microalgae cultivation and wastewater treatment using high-rate ponds: a meta-analysis

Microalgae cultivation in wastewater has been widely researched under laboratory conditions as per its potential to couple treatment with biomass production. Currently, only a limited number of published articles consider outdoor and long-term microalgae-bacteria cultivations in real wastewater environmental systems. The scope of this work is to describe microalgal cultivation steps towards high-rate algal pond (HRAP) scalability and identify key parameters that play a major role for biomass productivity under outdoor conditions and long-term cultivations. Reviewed pilot-scale HRAP literature is analysed using multivariate analysis to highlight key productivity parameters within environmental and operational factors. Wastewater treatment analysis indicated that HRAP can effectively remove 90% of NH4+, 70% of COD, and 50% of PO43-. Mean reference values of 210 W m-2 for irradiation, 18 °C for temperature, pH of 8.2, and HRT of 7.7 are derived from pilot-scale cultivations. Microalgae biomass productivity at a large scale is governed by solar radiation and NH4+ concentration, which are more important than retention time variations within investigated studies. Hence, selecting the correct type of location and a minimum of 70 mg L-1 of NH4+ in wastewater will have the greatest effect in microalgae productivity. A high nutrient wastewater content increases final biomass concentrations but not necessarily biomass productivity. Pilot-scale growth rates (~ 0.54 day-1) are half those observed in lab experiments, indicating a scaling-up bottleneck. Microalgae cultivation in wastewater enables a circular bioeconomy framework by unlocking microalgal biomass for the delivery of an array of products.

Effects of microalgal (Tetradesmus obliquus MCX38) attachment on photobioreactor treatment efficiency of raw swine wastewater

Attachment of microalgae on the inner surfaces of photobioreactors impacts the efficiency of swine wastewater treatment by reducing the light intensity, which has been overlooked in previous studies. This study investigated the relationship between microalgal attachment biomass and light intensity in photobioreactors, determined the optimal attachment time for effective pollutant removal, and clarified the mechanisms of microalgal attachment in swine wastewater. After 9 days of treatment, the attached biomass in the photobioreactor increased from 0 to 6.4 g/m2, decreasing the light intensity from 2,000 to 936 lux. At the 24 h optimal attachment time, the concentrations of chemical oxygen demand, ammonia nitrogen, and total phosphorus decreased from 2725.1, 396.4, and 87.2 mg/L to 361.2, 4.9, and 0.8 mg/L, respectively. Polysaccharides in the extracellular polymeric substances released by microalgae play a significant role in facilitating microalgae attachment. Optimizing the microalgal attachment time within photobioreactors effectively mitigates pollutant concentrations in swine wastewater.

Viability of Total Ammoniacal Nitrogen Recovery Using a Polymeric Thin-Film Composite Forward Osmosis Membrane: Determination of Ammonia Permeability Coefficient

Total ammoniacal nitrogen (TAN) occurs in various wastewaters and its recovery is vital for environmental reasons. Forward osmosis (FO), an energy-efficient technology, extracts water from a feed solution (FS) and into a draw solution (DS). Asymmetric FO membranes consist of an active layer and a support layer, leading to internal concentration polarization (ICP). In this study, we assessed TAN recovery using a polymeric thin-film composite FO membrane by determining the permeability coefficients of NH4+ and NH3. Calculations employed the solution-diffusion model, Nernst-Planck equation, and film theory, applying the acid-base equilibrium for bulk concentration corrections. Initially, model parameters were estimated using sodium salt solutions as the DS and deionized water as the FS. The NH4+ permeability coefficient was 0.45 µm/s for NH4Cl and 0.013 µm/s for (NH4)2SO4 at pH < 7. Meanwhile, the NH3 permeability coefficient was 6.18 µm/s at pH > 9 for both ammonium salts. Polymeric FO membranes can simultaneously recover ammonia and water, achieving 15% and 35% recovery at pH 11.5, respectively.

The Performance and Spatial Distribution of Membrane Fouling in a Sequencing Batch Ceramic Membrane Bioreactor: A Pilot Study for Swine Wastewater Treatment

The extensive application of ceramic membranes in wastewater treatment draws increasing attention due to their ultra-long service life. A cost-effective treatment for high-strength swine wastewater is an urgent and current need that is a worldwide challenge. A pilot-scale sequencing batch flat-sheet ceramic membrane bioreactor (ScMBR) coupled with a short-cut biological nitrogen removal (SBNR) process was developed to treat high-strength swine wastewater. The ScMBR achieved stable and excellent removal of COD (95.3%), NH4+-N (98.3%), and TN (92.7%), though temperature went down from 20 °C, to 15 °C, to 10 °C stepwise along three operational phases. The COD and NH4+-N concentrations in the effluent met with the discharge standards (GB18596-2001). Microbial community diversity was high, and the genera Pseudomonas and Comamonas were dominant in denitritation, and Nitrosomonas was dominant in nitritation. Ceramic membrane modules of this pilot-scale reactor were separated into six layers (A, B, C, D, E, F) from top to bottom. The total filtration resistance of both the top and bottom membrane modules was relatively low, and the resistance of the middle ones was high. These results indicate that the spatial distribution of the membrane fouling degree was different, related to different aeration scour intensities demonstrated by computational fluid dynamics (CFD). The results prove that the membrane fouling mechanism can be attributed to the cake layer formation of the middle modules and pore blocking of the top and bottom modules, which mainly consist of protein and carbohydrates. Therefore, different cleaning measures should be adopted for membrane modules in different positions. In this study, the efficient treatment of swine wastewater shows that the ScMBR system could be applied to high-strength wastewater. Furthermore, the spatial distribution characteristics of membrane fouling contribute to cleaning strategy formulation for further full-scale MBR applications.

Mechanism of microplastics effects on the purification of heavy metals in piggery effluents by microalgae

Microalgae is an effective bioremediation technique employed for treating piggery effluent. However, there is insufficient study on how the presence of microplastics (MPs) in wastewater affects the ability of microalgae to remove heavy metals from piggery effluent. This study aims to investigate the influence of two prevalent heavy metals found in piggery wastewater, Cu2+ (2 mg/L) and Zn2+ (2 mg/L), on their removal by microalgae (Desmodesmus sp. CHX1) in the presence of four types of MPs: polyethylene (PE), polyvinyl chloride (PVC), polypropylene (PP), and polyethylene terephthalate (PET). The results revealed that smaller particle size MPs promoted chlorophyll accumulation, while larger particles inhibits it. Additionally, higher concentrations of MPs promoted chlorophyll accumulation, while lower concentrations inhibited it. As for heavy metals, the presence of microplastics reduced the removal efficiency of Cu2+ and Zn2+ by Desmodesmus sp. CHX1. The highest inhibition of Cu2+ was 30%, 10%, 19%, and 16% of the control (CK), and the inhibition of Zn2+ was 7%, 4%, 4%, and 13%, respectively, under the treatments of PE, PVC, PP and PET MPs. Furthermore, Desmodesmus sp. CHX1 can secrete more extracellular polymeric substances (EPS) and form heterogeneous aggregates with MPs to counteract their pressure. These findings elucidate the impact of MPs on microalgae in bioremediation settings and offer useful insights into the complex relationships between microalgae, MPs, and heavy metals in the environment.

Recent advances in swine wastewater treatment technologies for resource recovery: A comprehensive review

Swine wastewater (SW), characterized by highly complex organic and nutrient substances, poses serious impacts on aquatic environment and public health. Furthermore, SW harbors valuable resources that possess substantial economic potential. As such, SW treatment technologies place increased emphasis on resource recycling, while progressively advancing towards energy saving, sustainability, and circular economy principles. This review comprehensively encapsulates the state-of-the-art knowledge for treating SW, including conventional (i.e., constructed wetlands, air stripping and aerobic system) and resource-utilization-based (i.e., anaerobic digestion, membrane separation, anaerobic ammonium oxidation, microbial fuel cells, and microalgal-based system) technologies. Furthermore, this research also elaborates the key factors influencing the SW treatment performance, such as pH, temperature, dissolved oxygen, hydraulic retention time and organic loading rate. The potentials for reutilizing energy, biomass and digestate produced during the SW treatment processes are also summarized. Moreover, the obstacles associated with full-scale implementation, long-term treatment, energy-efficient design, and nutrient recovery of various resource-utilization-based SW treatment technologies are emphasized. In addition, future research prospective, such as prioritization of process optimization, in-depth exploration of microbial mechanisms, enhancement of energy conversion efficiency, and integration of diverse technologies, are highlighted to expand engineering applications and establish a sustainable SW treatment system.

Growth, nutrient removal, and lipid productivity promotion of Chlorella sorokiniana by phosphate solubilizing bacteria Bacillus megatherium in swine wastewater: Performances and mechanisms

Effects of a phosphorus-solubilizing bacteria (PSB) Bacillus megatherium on growth and lipid production of Chlorella sorokiniana were investigated in synthesized swine wastewater with dissolved inorganic phosphorus (DIP), insoluble inorganic phosphorus (IIP), and organic phosphorus (OP). The results showed that the PSB significantly promoted the algal growth in OP and IIP, by 1.10 and 1.78-fold, respectively. The algal lipid accumulation was also greatly triggered, respectively by 4.39, 1.68, and 1.38-fold in DIP, IIP, and OP. Moreover, compared with DIP, OP improved the oxidation stability of algal lipid by increasing the proportion of saturated fatty acids (43.8 % vs 27.9 %), while the PSB tended to adjust it to moderate ranges (30.2-41.6 %). Further, the transcriptome analysis verified the OP and/or PSB-induced up-regulated genes involving photosynthesis, lipid metabolism, signal transduction, etc. This study provided novel insights to enhance microalgae-based nutrient removal combined with biofuel production in practical wastewater, especially with complex forms of phosphorus.

An integrated meta-omics approach reveals the different response mechanisms of two anammox bacteria towards fluoroquinolone antibiotics

The emerging fluoroquinolone antibiotics (FQs) are highly influential in nitrogen removal from livestock wastewater. However, beyond the capability of nitrogen removal, little is known about the molecular mechanisms (e.g., shift of core metabolism and energy allocation) of different anaerobic ammonium-oxidizing bacteria (AnAOB) under continuous FQ stress. This study investigated the effects of ciprofloxacin, ofloxacin and their mixture at concentrations detected in livestock wastewater on two key anammox species in membrane bioreactors. It was found 20 μg/L FQs promoted nitrogen removal efficiency and community stability, and42-51 % of FQs were removed simultaneously. Integrated meta-omics analysis revealed varied gene expression patterns between the two dominant AnAOB, Candidatus Brocadia sapporoensis (B AnAOB) and Candidatus Kuenenia stuttgartiensis (K AnAOB). The nitrogen metabolic processes were bolstered in B AnAOB, while those involved in anammox pathway of K AnAOB were inhibited. This difference was tentatively attributed to the up-regulation of reactive oxygen species scavenger genes (ccp and dxf) and FQ resistance gene (qnrB72) in B AnAOB. Importantly, most enhanced core biosynthesis/metabolism of AnAOB and close cross-feeding with accompanying bacteria were also likely to contribute to their higher levels of biomass yield and metabolism activity under FQ stress. This finding suggests that B AnAOB has the advantage of higher nitrogen metabolism capacity over K AnAOB in livestock wastewater containing FQs, which is helpful for efficient and stable nitrogen removal by the functional anammox species.

Microalgae cultivation for treating agricultural effluent and producing value-added products

Wastewater generated within agricultural sectors such as dairies, piggeries, poultry farms, and cattle meat processing plants is expected to reach 600 million m3 yr-1 globally. Currently, the wastewater produced by these industries are primarily treated by aerobic and anaerobic methods. However, the treated effluent maintains a significant concentration of nutrients, particularly nitrogen and phosphorus. On the other hand, the valorisation of conventional microalgae biomass into bioproducts with high market value still requires expensive processing pathways such as dewatering and extraction. Consequently, cultivating microalgae using agricultural effluents shows the potential as a future technology for producing value-added products and treated water with low nutrient content. This review explores the feasibility of growing microalgae on agricultural effluents and their ability to remove nutrients, specifically nitrogen and phosphorus. In addition to evaluating the market size and value of products from wastewater-grown microalgae, we also analysed their biochemical characteristics including protein, carbohydrate, lipid, and pigment content. Furthermore, we assessed the costs of both upstream and downstream processing of biomass to gain a comprehensive understanding of the economic potential of the process. The findings from this study are expected to facilitate further techno-economic and feasibility assessments by providing insights into optimized processing pathways and ultimately leading to the reduction of costs.

Combined zeolite-based ammonia slow-release and algae-yeast consortia to treat piggery wastewater: Improved nitrogen and carbon migration

Integration of zeolite-based ammonia adsorption and algae-yeast consortia was developed to remediate piggery wastewater (PW) containing high concentrations of total ammonia nitrogen (TAN) and total organic carbon (TOC). After optimizing the conditions of ammonia adsorption in the PW. Zeolite addition mitigated ammonia toxicity, allowing zeolites to gradually release ammonia while effectively attenuating algal oxidative stress caused by high TAN concentration. Coupling zeolite-based adsorption and yeast co-incubation further increased TOC degradation and available C/N ratio, thus improving biomass (4.51 g/L), oil yield (2.11 g/L), and nutrient removal (84.18%-99.14%). The integrated microalgae-based PW treatment exhibited higher carbon migration into biomass (46.14%) and reduced treatment costs than conventional approaches. Simultaneously, the lowest carbon migration to wastewater also meant the smallest carbon emission into water bodies. These findings demonstrate that this novel strategy can remove nutrients in raw PW effectively and produce high oil-rich biomass in a sustainable and environmentally-friendly manner.

Copper regulates degradation of typical antibiotics by microalgal-fungal consortium in simulated swine wastewater: insights into metabolic routes and dissolved organic matters

Microalgae-based biotechnology for antibiotics biodegradation in swine wastewater has been receiving an increasing attention. In this study, microalgae and fungi co-cultivation system, regulated by copper (Cu(II)), was investigated in terms of nutrients and sulfonamides degradation in simulated swine wastewater. Results showed that the removal of ammonium nitrogen (NH4+-N), total nitrogen (TN), total phosphorus (TP) and chemical oxygen demand (COD) by microalgal-fungal consortium increased under 0.1-0.5 mg/L Cu(II) with the highest removal efficiency of 79.19%, 76.18%, 93.93% and 93.46%, respectively. The addition of Cu(II) (0-0.5 mg/L) enhanced the removal of sulfamonomethoxine (SMM), sulfamethoxazole (SMX) and sulfamethazine (SMZ) from 49.05% to 58.76%, from 59.31% to 63.51%, and from 37.51% to 63.9%, respectively, and the main removal mechanism was found to be biodegradation. Biodegradation followed a pseudo-first-order model with variable half-lives (10.12 to 15.51 days for SMM, 9.01 to 10.88 days for SMX, and 8.74 to 12.85 days for SMZ). Through mass spectrometry analysis, metabolites and intermediates of sulfonamides were accordingly identified, suggesting that the degradation routes were involved with hydroxylation, deamination, oxidation, de-sulfonation and bond cleavage. Dissolved organic matters released by microalgal-fungal consortium were induced by Cu(II). Fulvic acid-like and protein-like substances were bound to Cu(II), reducing its concentration and thus mitigating the organismal damage to microorganisms. These findings drew an insightful understanding of microalgal-fungal consortium for sulfonamides remediation by Cu(II) regulation in simulated swine wastewater.

Stress of cupric ion and oxytetracycline in Chlorella vulgaris cultured in swine wastewater

Chlorella culturing has the advantages in treatment of wastewater including swine wastewater from anaerobic digesters due to the product of biolipids and the uptake of carbon dioxide. However, there often exist high concentrations of antibiotics and heavy metals in swine wastewater which could be toxic to chlorella and harmful to the biological systems. This study examined the stress of cupric ion and oxytetracycline (OTC) at various concentrations on the nutrient removal and biomass growth in Chlorella vulgaris culturing in swine wastewater from anaerobic digesters, and its biochemical responses were also studied. Results showed that dynamic hormesis of either OTC concentration or cupric ion one on Chlorella vulgaris were confirmed separately, and the presence of OTC not only did not limit biomass growth and lipids content of Chlorella vulgaris but also could mitigate the toxicity of cupric ion on Chlorella vulgaris in combined stress of Cu2+ and OTC. Extracellular polymeric substances (EPS) of Chlorella vulgaris were used to explain the mechanisms of stress for the first time. The content of proteins and carbohydrates in EPS increased, and the fluorescence spectrum intensity of tightly-bound EPS (TB-EPS) of Chlorella vulgaris decreased with increasing concentration of stress because Cu2+ and OTC may be chelated with proteins of TB-EPS to form non-fluorescent characteristic chelates. The low concentration of Cu2+ (≤1.0 mg/L) could enhance the protein content and promote the activity of superoxide dismutase (SOD) while these parameters were decreased drastically under 2.0 mg/L of Cu2+. The activity of adenosine triphosphatase (ATPase) and glutathione (GSH) enhanced with the increase of OTC concentration under combined stress. This study helps to comprehend the impact mechanisms of stress on Chlorella vulgaris and provides a novel strategy to improve the stability of microalgae systems for wastewater treatment.

The presence of copper ions alters tetracycline removal pathway in aerobic granular sludge: Performance and mechanism

This study investigated the removal characteristics of tetracycline (TC) in the presence of copper ions (Cu2+) in aerobic granular sludge by analyzing the TC removal pathway, composition and functional group changes of extracellular polymeric substances (EPS), and microbial community structure. The TC removal pathway changed from cell biosorption to EPS biosorption, and the microbial degradation rate of TC was reduced by 21.37% in the presence of Cu2+. Cu2+ and TC induced enrichment of denitrifying bacteria and EPS-producing bacteria by regulating the expression of signaling molecules and amino acid synthesis genes to increase the content of EPS and -NH2 groups in EPS. Although Cu2+ reduced the content of acidic hydroxyl functional groups (AHFG) in EPS, an increase in TC concentration stimulated the secretion of more AHFG and -NH2 groups in EPS. The long-term presence of TC presence of the relative abundances of Thauera, Flavobacterium and Rhodobacter and improved the removal efficiency.

The effect of initial inoculation amount of microalgae on synergistic purification of biogas slurry

In this study, Chlorella and Scenedesmus were inoculated in biogas slurry medium with initial inoculum (OD680) of 0.05, 0.1, 0.2, and 0.3, respectively, and 5% CO2 was continuously injected. The study aimed to examine the carbon sequestration capacity of Chlorella and Scenedesmus, as well as the effectiveness of removing pollutants such as TN, TP, and COD in biogas slurry medium. Additionally, an economic efficiency analysis of energy consumption was conducted. The group with an initial inoculum (OD680) of 0.3 for both types of microalgae exhibited better tolerance to pollutants, entered the logarithmic growth stage earlier, promoted nutrient removal, achieved higher energy efficiency, and reduced carbon emissions compared to the other groups. The highest carbon sequestration rates were 18.03% for Chlorella and 11.05% for Scenedesmus. Furthermore, Chlorella demonstrated corresponding nutrient removal efficiencies of 83.03% for TN, 99.84% for TP, and 90.06% for COD, while Scenedesmus exhibited removal efficiencies of 66.35% for TN, 98.74% for TP, and 77.71% for COD. The highest energy efficiency for pollutants and CO2 removal rates for Chlorella were 49.51 ± 2.20 and 9.91 ± 0.44 USD-1, respectively. In conclusion, the findings demonstrate the feasibility of using microalgae for simultaneous purification of biogas and biogas slurry.

The potential and sustainable strategy for swine wastewater treatment: Resource recovery

Swine wastewater is highly polluted with complex and harmful substances that require effective treatment to minimize environmental damage. There are three commonly used biological technologies for treating swine wastewater: conventional biological technology (CBT), microbial electrochemical technology (MET), and microalgae technology (MT). However, there is a lack of comparison among these technologies and a lack of understanding of their unique advantages and efficient operation strategies. This review aims to compare and contrast the characteristics, influencing factors, improvement methods, and microbial mechanisms of each technology. CBT is cost-effective but has low resource recovery efficiency, while MET and MT have the highest potential for resource recovery. However, all three technologies are affected by various factors and toxic substances such as heavy metals and antibiotics. Improved methods include exogenous/endogenous enhancement, series reactor operation, algal-bacterial symbiosis system construction, etc. Though MET is limited by construction costs, CBT and MT have practical applications. While swine wastewater treatment processes have developed automatic control systems, the application need further promotion. Furthermore, key functional microorganisms involved in CBT's pollutant removal or transformation have been detected, as have related genes. The unique electroactive microbial cooperation mode and symbiotic mode of MET and MT were also revealed, respectively. Importantly, the future research should focus on broadening the scope and scale of engineering applications, preventing and controlling emerging pollutants, improving automated management level, focusing on microbial synergistic metabolism, enhancing resource recovery performance, and building a circular economy based on low-cost and resource utilization.

Heavy metal tolerance in microalgae: Detoxification mechanisms and applications

The proficiency of microalgae to resist heavy metals has potential to be beneficial in resolving various environmental challenges. Global situations such as the need for cost-effective and ecological ways of remediation of contaminated water and for the development of bioenergy sources could employ microalgae. In a medium with the presence of heavy metals, microalgae utilize different mechanisms to uptake the metal and further detoxify it. Biosorption and the next process of bioaccumulation are two such major steps and they also include the assistance of different transporters at different stages of heavy metal tolerance. This capability has also proved to be efficient in eradicating many heavy metals like Chromium, Copper, Lead, Arsenic, Mercury, Nickel and Cadmium from the environment they are present in. This indicates the possibility of the application of microalgae as a biological way of remediating contaminated water. Heavy metal resistance quality also allows various microalgal species to contribute in the generation of biofuels like biodiesel and biohydrogen. Many research works have also explored the capacity of microalgae in nanotechnology for the formation of nanoparticles due to its relevant characteristics. Various studies have also revealed that biochar deduced from microalgae or a combination of biochar and microalgae can have wide applications specially in deprivation of heavy metals from an environment. This review focuses on the strategies adopted by microalgae, various transporters involved in the process of tolerating heavy metals and the applications where microalgae can participate owing to its ability to resist metals.

Microbial community structure analyses and cultivable denitrifier isolation of Myriophyllum aquaticum constructed wetland under low C/N ratio

With the rapid expansion of livestock production, the amount of livestock wastewater accumulated rapidly. Lack of biodegradable organic matter makes denitrification of livestock wastewater after anaerobic digestion more difficult. In this study, Myriophyllum aquaticum constructed wetlands (CWs) with efficient nitrogen removal performance were established under different carbon/nitrogen (C/N) ratios. Analysis of community composition reveals the change of M. aquaticum CWs in microbial community structure with C/N ratios. The proportion of Proteobacteria which is one of the dominant phyla among denitrifier communities increased significantly under low C/N ratio conditions. Besides, to obtain cultivable denitrifier that could be added into CWs in situ, 33 strains belonging to phylum Proteobacteria were isolated from efficient M. aquaticum CWs, while the best-performing denitrification strain M3-1 was identified as Bacillus velezensis JT3-1 (GenBank No. CP032506.1). Redundancy analysis and quadratic models showed that C/N ratio had significant effects on disposal of nitrate (NO₃^--N) and the strains isolated could perform well in denitrification when C/N ratio is relatively low. In addition, they have relatively wide ranges of carbon sources, temperature and a high NO₃^- removal rate of 9.12 mg/(L·hr) at elevated concentrations of 800 mg/L nitrate. Thus, strains isolated from M. aquaticum CWs with low C/N ratio have a practical application value in the treatment of nitrate-containing wastewater. These denitrifying bacteria could be added to CWs to enhance nitrogen removal efficiency of CWs for livestock wastewater with low C/N ratio in the future.

Tracing the variation of dissolved organic matter in the two-stage anoxic/aerobic process treating swine wastewater using fluorescence excitation-emission matrix with parallel factor analysis

Swine wastewater has become one of the main agricultural pollution sources. Quantitative characterization of dissolved organic matter (DOM) is often used in various water bodies, but there are few studies on DOM analysis of swine wastewater. In this study, swine wastewater was treated by a step-feed two-stage anoxic/aerobic (SF-A/O/A/O) process. By using parallel factor (PARAFAC) analysis of fluorescence excitation-emission matrix (EEM), the main components of swine wastewater were aromatic protein-like substances (C1), tryptophan-like substances (C2), fulvic acid-like/humic-like substances (C3) and humic-like substances (C4). Protein-like substances were degraded significantly, while humic-like substances were difficult to be utilized by microorganisms. Fluorescence spectral indexes showed that the characteristics of endogenous input and humus were enhanced. Moreover, several significant correlations between DOM components, fluorescence spectral indexes and water quality indexes were observed. These findings help to understand the biochemical role and the impact of DOM in water quality monitoring and control of swine wastewater.

The coexistence of copper ions and TC affected the binding ability and the reaction order between extracellular polymeric substances of aerobic granular sludge and exogenous substances

As a barrier against external toxic effects, extracellular polymeric substances (EPSs) directly affect the toxicity and removal efficiency of exogenous substances. The reaction of EPSs with exogenous substances has been taken into consideration. The contents of EPSs in sludge cultivated by different influent water vary greatly, which leads to great differences in the binding ability and reaction sequence between EPSs and exogenous substances. However, the results in this respect are very limited. In this study, the binding characteristics between exogenous tetracycline (TC)/copper ions (Cu²⁺) and EPSs from aerobic granular sludge cultured under single and coexisting TC/Cu²⁺ were assessed by three-dimensional fluorescence-parallel factor analysis. The pollutants in the influent water could directionally induce microorganisms to secrete more EPSs, while fluorescence substances in EPSs could combine with the exogenous substances to lessen their effects. In the presence of coexisting TC and Cu²⁺ in the influent water, the ability of fluorescence substances in EPSs to combine with exogenous TC or Cu²⁺ weakened, and humic substances in EPSs were more susceptible than protein substances to binding with exogenous substances. However, the reaction order between EPSs components and exogenous TC or Cu²⁺ was opposite, and the ability of fluorescence substances in EPSs to combine with exogenous TC or Cu²⁺ was enhanced under individual TC or Cu²⁺ existing in the influent water. This study provided new insights into the interaction between EPSs and exogenous substances.

Chitosan-coated oleaginous microalgae-fungal pellets for improved bioremediation of non-sterile secondary effluent and application in carbon dioxide sequestration in bubble column photobioreactors

Oleaginous microalga Scenedesmus sp. SPP was rapidly immobilized in oleaginous fungal pellets by their opposite-surface-charges. Microalgae-fungal (MF) pellets were more effective in bioremediation of non-sterile secondary effluent than mono-culture. The optimal hydraulic retention time for dual bioremediation in semi-continuous mode was 72 h. The MF pellets coated with 0.4 %-chitosan improved removal efficiencies of COD, total nitrogen (TN), and total phosphorus (TP) up to 96.2±0.0 %, 88.2±2.8 % and 71.5±0.7 %, respectively, likely because of better cell retention and more nutrient adsorption and assimilation. Dual bioremediation by coated MF pellets was also successfully scaled up in 30-L bubble-column photobioreactors with improved COD, TN, and TP removal efficiencies of 98.5±0.0 %, 90.2±0.0 % and 79.5±2.1 %, respectively. This system also effectively removed CO₂ from simulated flue gas at 71.2±0.4 % and produced biomass with high lipid content. These results highlight the effectiveness of bio-immobilization by fungal pellets; chitosan coating; and their practical applications in bioremediation and CO₂ sequestration.

Recent approaches and advanced wastewater treatment technologies for mitigating emerging microplastics contamination - A critical review

Microplastics have been identified as an emerging pollutant due to their irrefutable prevalence in air, soil, and particularly, the aquatic ecosystem. Wastewater treatment plants (WWTPs) are seen as the last line of defense which creates a barrier between microplastics and the environment. These microplastics are discharged in large quantities into aquatic bodies due to their insufficient containment during water treatment. As a result, WWTPs are regarded as point sources of microplastics release into the environment. Assessing the prevalence and behavior of microplastics in WWTPs is therefore critical for their control. The removal efficiency of microplastics was 65 %, 0.2-14 %, and 0.2-2 % after the successful primary, secondary and tertiary treatment phases in WWTPs. In this review, other than conventional treatment methods, advanced treatment methods have also been discussed. For the removal of microplastics in the size range 20-190 μm, advanced treatment methods like membrane bioreactors, rapid sand filtration, electrocoagulation and photocatalytic degradation was found to be effective and these methods helps in increasing the removal efficiency to >99 %. Bioremediation based approaches has found that sea grasses, lugworm and blue mussels has the ability to mitigate microplastics by acting as a natural trap to the microplastics pollutants and could act as candidate species for possible incorporation in WWTPs. Also, there is a need for controlling the use and unchecked release of microplastics into the environment through laws and regulations.

Emerging trends in the pretreatment of microalgal biomass and recovery of value-added products: A review

Microalgae are a promising source of raw material (i.e., proteins, carbohydrates, lipids, pigments, and micronutrients) for various value-added products and act as a carbon sink for atmospheric CO₂. The rigidity of the microalgal cell wall makes it difficult to extract different cellular components for its applications, including biofuel production, food and feed supplements, and pharmaceuticals. To improve the recovery of products from microalgae, pretreatment strategies such as biological, physical, chemical, and combined methods have been explored to improve whole-cell disruption and product recovery efficiency. However, the diversity and uniqueness of the microalgal cell wall make the pretreatment process more species-specific and limit its large-scale application. Therefore, advancing the currently available technologies is required from an economic, technological, and environmental perspective. Thus, this paper provides a state-of-art review of the current trends, challenges, and prospects of sustainable microalgal pretreatment technologies from a microalgae-based biorefinery concept.

Growth of Scenedesmus dimorphus in swine wastewater with versus without solid-liquid separation pretreatment

Scenedesmus dimorphus was cultivated in raw and pretreated swine wastewater (SW) with 6-L photobioreactors (PBRs) to investigate the effect of solid-liquid separation on algal growth. The same aerated PBRs containing no algae were used as control. Moderate COD and nitrogen removal from the SW was achieved with the algal PBRs. However, compared to the control reactors, they offered no consistent treatment boost. Improved algal growth occurred in the pretreated SW, as measured by maximum algal cell count (3202 ± 275 × 10⁶ versus 2286 ± 589 × 10⁶ cells L^-1) and cell size. The enhanced algal growth in the pretreated SW resulted in relatively high nitrogen (5.7 %) and organic matter contents in the solids harvested at the end of cultivation experiments, with ∼25.6 % of nitrogen in the SW retained in the solids and ∼9.1 % absorbed by algae. The pretreatment also resulted in elevated phosphorus removal. This study is anticipated to foster the development of microalgae-based SW treatment processes.

A rapid, efficient and eco-friendly approach for simultaneous biomass harvesting and bioproducts extraction from microalgae: Dual flocculation between cationic surfactants and bio-polymer

Microalgal biomass harvesting and cell disruption are the main bottlenecks for downstream processing of microalgae such as high-value bioproducts extraction and biofuels production. In this study, we evaluated the performance of dual flocculation between cationic surfactants and bio-polymer of chitosan for simultaneous biomass harvesting and bioproducts extraction from Chlorella sorokiniana microalgae. First, the effects of individual natural flocculants of chitosan and two cationic surfactants: cetyltrimethylammonium bromide (CTAB) and dodecyltrimethylammonium bromide (DTAB) on biomass harvesting were studied. Next, the synergistic effect of dual flocculation between the cationic surfactants and chitosan on harvesting efficiency, time and flocculant dosage was investigated. Finally, we evaluated the potential of high value bioproducts extraction from microalgae after the individual and dual flocculation processes. Zeta potential analysis and microscopic images were employed to achieve mechanistic understanding. Maximum biomass harvesting efficiencies of 85 %, 88 % and 78 % were achieved using individual flocculants of chitosan, CTAB and DTAB, under their optimum dosages of 100, 400 and 4000 mg/L, respectively. A significant synergistic effect of dual flocculation between chitosan (C) and cationic surfactants on biomass harvesting efficiency (CTAB-C: 99 % and DTAB-C: 97 %), settling time (CTAB-C: 2 min and DTAB-C: 5 min) and optimum dosage of surfactants (CTAB-C: 100 mg/L and DTAB-C: 1000 mg/L) was observed. The synergistic effect was associated with multiple flocculation mechanisms of charge neutralization and bridging induced by cationic surfactants and chitosan, respectively. Furthermore, bioproducts recovery efficiencies of 12 %, 25 % and 15 % of cell dry weight were achieved for protein, carbohydrate and lipid, respectively by using dual flocculation of CTAB surfactant and chitosan at much lower dosage of 100 mg/L.

Role of microalgae in achieving sustainable development goals and circular economy

In 2015, the United Nations General Assembly (UNGA) set out 17 Sustainable Development Goals (SDGs) to be achieved by 2030. These goals highlight key objectives that must be addressed. Each target focuses on a unique perspective crucial to meeting these goals. Social, political, and economic issues are addressed to comprehensively review the main issues combating climate change and creating sustainable and environmentally friendly industries, jobs, and communities. Several mechanisms that involve judicious use of biological entities are among instruments that are being explored to achieve the targets of SDGs. Microalgae have an increasing interest in various sectors, including; renewable energy, food, environmental management, water purification, and the production of chemicals such as biofertilizers, cosmetics, and healthcare products. The significance of microalgae also arises from their tendency to consume CO2, which is the main greenhouse gas and the major contributor to the climate change. This work discusses the roles of microalgae in achieving the various SDGs. Moreover, this work elaborates on the contribution of microalgae to the circular economy. It was found that the microalgae contribute to all the 17th SDGs, where they directly contribute to 9th of the SDGs and indirectly contribute to the rest. The major contribution of the Microalgae is clear in SDG-6 "Clean water and sanitation", SDG-7 "Affordable and clean energy", and SDG-13 "Climate action". Furthermore, it was found that Microalgae have a significant contribution to the circular economy.

Long term outdoor microalgal phycoremediation of anaerobically digested abattoir effluent

Sufficient and reliable long-term field data on the growth, productivity and nutrient removal rates of microalgal based wastewater treatment system is essential to validate its overall techno-economic feasibility. Here, we investigated the semi-continuous microalgal cultivation of Scenedesmus sp. in anaerobically digested abattoir effluent (ADAE) for 13 months in outdoor raceway ponds operated at 20 cm depth. This study was initiated with three different cultures consisting of 1) monocultures of Chlorella sp., 2) Scenedesmus sp., and 3) an equal mixed concentration of both microalgae species. However, after 15 weeks, Scenedesmus sp. was found to be the most dominant microalgae species in all the different cultures, even completely taking over the Chlorella sp. monoculture. Over the course of summer and early autumn, the average weekly biomass productivity of Scenedesmus sp. cultures was 12.5 ± 0.6 g m^-2 d^-1 which was 16% and 30% higher than productivities recorded in spring and winter, respectively. All available ammoniacal nitrogen (NH₃-N) was found to be exhausted during each growth period with an average 33.6% nitrogen assimilation rate. The average rate of phosphate and COD (chemical oxygen demand) removals were 85.2% and 37.5% throughout the cultivation period. No significant differences were found in carbohydrate, lipid and protein content of Scenedesmus sp. during different seasons of the year. Over 53% increase in biomass productivity can be achieved if CO₂ is added to control culture pH at pH 6.5. Here, we successfully demonstrated reliability of continuous long-term cultivation of microalgae in ADAE for simultaneous wastewater treatment and algal biomass production.

Removal of oxytetracycline and ofloxacin in wastewater by microalgae-bacteria symbiosis for bioenergy production

The development of microalgae-bacteria symbiosis for treating wastewater is flourishing owing to its high biomass productivity and exceptional ability to purify contaminants. A nature-selected microalgae-bacteria symbiosis, mainly consisting of Dictyosphaerium and Pseudomonas, was used to treat oxytetracycline (OTC), ofloxacin (OFLX), and antibiotic-containing swine wastewater. Increased antibiotic concentration gradually reduced biomass productivity and intricately changed symbiosis composition, while 1 mg/L OTC accelerated the growth of symbiosis. The symbiosis biomass productivity reached 3.4-3.5 g/L (5.7-15.3 % protein, 18.4-39.3 % carbohydrate, and 2.1-3.9 % chlorophyll) when cultured in antibiotic-containing swine wastewater. The symbiosis displayed an excellent capacity to remove 76.3-83.4 % chemical oxygen demand, 53.5-62.4 % total ammonia nitrogen, 97.5-100.0 % total phosphorus, 96.3-100.0 % OTC, and 32.8-60.1 % OFLX in swine wastewater. The microbial community analysis revealed that the existence of OTC/OFLX increased the richness and evenness of microalgae but reduced bacteria species in microalgae-bacteria, and the toxicity of OFLX to bacteria was stronger than that of OTC.

Production of forest seedlings using sewage sludge and automated irrigation with ozonated cattle wastewater

The large volume of effluents generated by intensive cattle production can become an environmental problem, requiring solutions that combine treatment and disposal of reuse water. The quality of cattle wastewater (CWW) treated by ozonation, the water requirement and its effect on the growth of seedlings of Dalbergia nigra cultivated with sewage sludge were determined under different light conditions. The study was carried out in a split plot scheme with 2 shading levels (0%—C₁, and 49.4% attenuation—C₂) and 3 types of irrigation water (control–T₁, 1 h ozonation–T₂, and 2 h–T₃), with 4 repetitions. Direct sowing was realized into 280 cm³ tubes which were irrigated by drip irrigation with automatic management. The height and collar diameter were measured every 21 days, and at the end of the nursery phase, and the Dickson quality index (DQI) and irrigation water productivity (WPir) were determined. In addition, seedlings were transplanted in a forest restauration area (FRA) of Atlantic Forest, with height and diameter monitoring for 200 days. With ozonation, there was an increase in pH and a reduction in electrical conductivity, total solids and turbidity in the CWW, allowing its use for irrigation of forest seedlings. The maximum volumes of water applied were 2.096 and 1.921 L plant^-1, with water supply T₂ and T₁, respectively, and coverages C₁ and C₂. In these conditions, the seedlings reached DQI of 0.47 and 0.17, and WPir of 2.35 and 1.48 g L^-1, respectively. The initial vegetative growth of the seedlings planted in the FRA was benefited by the nutrients provided by the CWW treated. Therefore, the use of sewage sludge and CWW treated has the potential to produce forest seedlings, reducing the release of waste and effluents into the environment.

State of microalgae-based swine manure digestate treatment: An overview

Global pork production has an annual growth of approximately 2.1%, and its economic and environmental impact are related with the treatment of waste in the production chain. There is little evidence of research advances to generate alternatives for using these wastes. The lack of research related to microalgae cultivation using digestate produced by porcine residues generates negative environmental impact, inadequate and inefficient technologies, low recovery and use of waste and loss of value and competitiveness in the market. The available literature focuses mainly on the treatment of anaerobic digestion liquid effluents for the removal of components, but not on the generation of value-added products. Therefore, there is a need to collect the available information, analyze it and propose other new methodologies. This article presents the information obtained from conducting a systematic review of the literature with a bibliometric and a comparative analysis; achieving an analysis of the temporal and geographical distribution, the main topics, the most influential players, the degree of maturity of the research and different strategies collected for microalgae-based swine manure digestate treatment. In this way, it was possible to capture an overview of the current state of the development of research focused on the use of digestate for the cultivation of microalgae, visualizing important aspects as the evolution of publications, identifying China and USA as the main players in research, biomass and wastewater as potential topics also Spirulina, Astaxanthin and beta-carotene as the main products based on microalgae. Thus, achieving an structure, organized and synthesized landscape of scientific and technological knowledge available for the proposal of investigations that allow the use of anaerobic digestion liquid effluents as cultivation medium for microalgae.

•

The biometric analysis and SAN provides an overview of the evolution of technology.

•

China and the USA are the main players in the use of digestate in microalgae cultivation.

•

Biomass and wastewater are trending topics in the microalgal application at the near future.

•

Spirulina, Astaxanthin and beta-carotene as the main products based on market worldwide forecasting.

Microalgae-driven swine wastewater biotreatment: Nutrient recovery, key microbial community and current challenges

As a promising technology, the microalgae-driven strategy can achieve environmentally sustainable and economically viable swine wastewater treatment. Currently, most microalgae-based research focuses on remediation improvement and biomass accumulation, while information on the removal mechanisms and dominant microorganisms is emerging but still limited. In this review, the major removal mechanisms of pollutants and pathogenic bacteria are systematically discussed. In addition, the bacterial and microalgal community during the swine wastewater treatment process are summarized. In general, Blastomonas, Flavobacterium, Skermanella, Calothrix and Sedimentibacter exhibit a high relative abundance. In contrast to the bacterial community, the microalgal community does not change much during swine wastewater treatment. Additionally, the effects of various parameters (characteristics of swine wastewater and cultivation conditions) on microalgal growth and current challenges in the microalgae-driven biotreatment process are comprehensively introduced. This review stresses the need to integrate bacterial and microalgal ecology information into the conventional design of full-scale swine wastewater treatment systems and operations. Herein, future research needs are also proposed, which will facilitate the development and operation of a more efficient microalgae-based swine wastewater treatment process.

Towards biomass production and wastewater treatment by enhancing the microalgae-based nutrients recovery from liquid digestate in an innovative photobioreactor integrated with dialysis bag

Microalgae-based nutrients recovery from liquid anaerobic digestate of swine manure has been a hotspot in recent decades. Nevertheless, in consideration of the high NH₄⁺-N content and poor light penetrability exhibited by the original liquid digestate, uneconomical pretreatment on liquid digestate including centrifugation and dilution are indispensable before microalgae cells inoculation. Herein, aiming at eliminating the energy-intensive and freshwater-consuming pretreatment on liquid digestate and enhancing microalgae growth, the dialysis bag which permits nutrients transferring across its wall surface whereas retains almost all matters characterized by impeding light transmission within the raw liquid digestate was integrated into a column photobioreactor (DB-PBR). Consequently, light availability of microalgae cells in DB-PBR was elevated remarkably and thus contributed to a 357.58% improvement on microalgae biomass concentration in DB-PBR than the conventional PBR under 80 μmol m^-2 s^-1. Likewise, superior nutrients removal efficiencies from liquid digestate were obtained in DB-PBR (NH₄⁺-N: 74.84%, TP: 63.75%) over the conventional PBR (NH₄⁺-N: 30.27%, TP: 16.86%). Furthermore, higher microalgae biomass concentration (1.87 g L^-1) and nutrients removal efficiencies (NH₄⁺-N: 95.12%, TP: 76.87%) were achieved in the DB-PBR by increasing the light intensity to 140 μmol m^-2 s^-1. More importantly, the DB-PBR may provide a simple and greener solution to purify other kinds of wastewater.

Current Concentrations of Zn, Cu, and As in Piggery Wastewater Compromise Nutrient Removals in Microalgae–Bacteria Photobioreactors Due to Altered Microbial Communities

Simple Summary

Photobioreactor systems based on consortia of microalgae and bacteria are a promising, efficient and sustainable alternative for treatment of wastewaters with high nitrogen content, such as piggery wastewater. In these biological systems, microorganisms play a key role in wastewater treatment by degradation of organic matter and accumulation of nutrients into the generated biomass. However, these wastewaters often contain high concentrations of zinc, copper and arsenic, which can severely affect the activity and growth of microorganisms, and so, the wastewater treatment performance. This article studies the effect of high concentrations of zinc, copper and arsenic on microbial communities, specifically microalgae and bacteria, in photobioreactors treating piggery wastewater, with the aim of elucidating their impact on wastewater treatment performance. For this purpose, the growth of microalgae and the composition and structure of bacterial communities exposed to these pollutants were studied. The performance of the reactors was also evaluated by determining the removal of nutrients, zinc, copper and arsenic. The results showed that high concentrations of zinc, copper and arsenic in piggery wastewater significantly affect the microbiome of the reactors without recovery after exposure to these contaminants, resulting in poorer performance of the reactors and compromising the environmental and health impact of treated effluents.

Abstract

The treatment of pig manure is a major environmental issue, and photobioreactors containing consortia of microalgae and bacteria have proven to be a promising and sustainable treatment alternative. This work studies the effect of Cu, Zn and As, three toxic elements frequently present in piggery wastewater, on the performance and microbiome of photobioreactors. After dopage with Zn (100 mg/L), Cu (100 mg/L), and As (500 µg/L), the high biomass uptake of Zn (69–81%) and Cu (81–83%) decreased the carbon removal in the photobioreactors, inhibited the growth of Chlorella sp., and affected heterotrophic bacterial populations. The biomass As uptake result was low (19%) and actually promoted microalgae growth. The presence of Cu and As decreased nitrogen removal, reducing the abundance of denitrifying bacterial populations. The results showed that metal(loid)s significantly affected 24 bacterial genera and that they did not recover after exposure. Therefore, this study makes an important contribution on the impact of the presence of metal(loid)s in piggery wastewater that compromises the overall performance of PBRs, and so, the environmental and health impact of treated effluents.

Response of fungi-microalgae pellets to copper regulation in the removal of sulfonamides and release of dissolved organic matters

Both sulfonamides (SAs) and copper (Cu(II)) were frequently detected together in swine wastewater. In this study, the regulation of Cu(II) on SAs adsorption and release of dissolved organic matters (DOMs) by fungi-microalgae pellets (FM-pellets) were investigated. Aspergillus oryzae pellets were prepared for combination with Chlorella vulgaris and the optimal conditions were at agitation speed of 130 rpm, fungi to microalgae ratio of 10:1 and the combined time of 3 h with the highest combination efficiency of 98.65%. The results showed that adsorption was the main mechanism for SAs removal. FM-pellets exhibited a high SAs adsorption potential within 6 h, and the adsorption capacity of sulfamethazine (SMZ), sulfamonomethoxine (SMM) and sulfamethoxazole (SMX) was 1.07, 0.94 and 1.67 mg/g, respectively. Furthermore, the removal of SMX, SMZ and SMM was greatly promoted from 62.31% to 85.21%, 58.71-67.91% and 64.17-80.31%, respectively, under the presence of 2 mg/L Cu(II) through ion exchange and adsorption bridging. DOMs were analyzed by the parallel factor (PARAFAC) to demonstrate the response mechanism of FM-pellets to Cu(II). Protein-like substances and NADH in DOMs released by FM-pellets formed complexes with Cu(II) to alleviate the damage on the organism. These findings provide new insights into the mechanism and response of Cu(II) in the removal of SAs by FM-pellets.

Continuous Production of Volatile Fatty Acids (VFAs) from Swine Manure: Determination of Process Conditions, VFAs Composition Distribution and Fermentation Broth Availability Analysis

For pollution control and waste utilization, a promising future direction is to obtain high-value carbon sources from organic waste. In this experiment, swine manure was efficiently converted into high concentration volatile fatty acids through continuous hydrolysis-acidification bioreactors. This study determined the process conditions, the composition distribution of volatile fatty acids and the availability of fermentation broth. The results showed that the reactor with a hydraulic retention time of 1.5 days had the optimal production performance of volatile fatty acids. The highest hydrolysis degree (62.2%) and acidification degree (42.5%) were realized in this reactor at the influent soluble chemical oxygen demand of 5460 mg/L. Furthermore, when the influent soluble chemical oxygen demand was 7660 mg/L, volatile fatty acids of 6065 mg-COD/L could be produced stably, and the proportion of volatile fatty acids in soluble chemical oxygen demand was the largest (75%). Additionally, the fermentation broth rich in volatile fatty acids could be applied to deep nitrogen and phosphorus removal. This work provides a productive approach to resource recovery from swine manure.

Morphological crystal adsorbing tetracyclines and its interaction with magnesium ion in the process of struvite crystallization by using synthetic wastewater

Struvite (MgNH₄PO₄·6H₂O) crystallization is a promising method of phosphorus recovery from wastewater. As for digestive livestock wastewater, the extensive residues of antibiotics could induce struvite recovery to spread antibiotic resistance and thereafter pose ecological risks to the environment. In this study, struvite crystals with different morphologies were produced from synthetic swine wastewater, and tetracyclines (TCs) adsorbing capacities were investigated. The important factors, including the existence of Mg²⁺ ions and initial TCs concentration, were examined. The predominant adsorption between TCs and struvite crystals was electrostatic interaction, with the maximum capacity at doxycycline (DXC) 876.5 μg/Kg, oxytetracycline (OTC) 1946.7 μg/Kg and tetracycline (TC) 2376.2 μg/Kg, respectively. Well-faceted struvite crystallites possessed high adsorption capacities than those of dendritic crystallite, due to higher Mg intensities on the crystallite surface. The increment of phosphorus concentration could trigger the transformation of struvite morphology from needle to dendritic shapes with X-shape as an intermediate stage, which would reduce Mg density in specific crystallite facets and therefore limit TCs adsorption onto struvite crystals. The existence of Mg²⁺ ion would inhibit TCs deprotonation and thereafter improve TCs adsorption onto struvite crystals. Further investigation revealed that continuously elevating initial TCs concentration would promote the formation of 1:2 transferring to 1:1 TCs-Mg chelates, which would result in a fluctuation following a drastic augment of TCs adsorption capacity.

Enhancing Algal Yield and Nutrient Removal from Anaerobic Digestion Piggery Effluent by an Integrated Process-Optimization Strategy of Fungal Decolorization and Microalgae Cultivation

The dark brown anaerobic digestion piggery effluent (ADPE) with a large amount of ammonium generally needs high dilution before microalgae cultivation due to its inhibiting effects on algal growth. Due to the strong decolorization of fungi by degrading organic compounds in wastewater, the process-optimization integrated strategy of fungal decolorization of ADPE and subsequent microalgae cultivation with ammonium-tolerant strain may be a more reliable procedure to reduce the dilution ratio and enhance algal biomass production, and nutrient removal from ADPE. This study determined a suitable fungal strain for ADPE decolorization, which was isolated and screened from a local biogas plant, and identified using 26s rRNA gene sequence analysis. Subsequently, ADPE was pretreated by fungal decolorization to make low-diluted ADPE suitable for the algal growth, and conditions of microalgae cultivation were optimized to achieve maximum algal yield and nutrient removal from the pretreated ADPE. The results showed one promising locally isolated fungal strain, Nanchang University-27, which was selected out of three candidates and identified as Lichtheimia ornata, presenting a high decolorization to ADPE through fungal pretreatment. Five-fold low-diluted ADPE pretreated by L. ornata was the most suitable medium for the algal growth at an initial concentration of ammonium nitrogen of 380 mg L−1 in all dilution treatments. Initial optical density of 0.3 and pH of 9.0 were optimal culture conditions for the algal strain to provide the maximum algal yield (optical density = 2.1) and nutrient removal (88%, 58%, 65%, and 77% for the removal rates of ammonium nitrogen, total nitrogen, total phosphorus, and chemical oxygen demand, respectively) from the pretreated ADPE. This study demonstrated that fungal decolorization and subsequent microalgae cultivation could be a promising approach to algal biomass production and nutrient removal from ADPE.

Partial Nitrification and Enhanced Biological Phosphorus Removal in a Sequencing Batch Reactor Treating High-Strength Wastewater

Complex and high levels of various pollutants in high-strength wastewaters hinder efficient and stable biological nutrient removal. In this study, the changes in pollutant removal performance and microbial community structure in a laboratory-scale anaerobic/aerobic sequencing batch reactor (SBR) treating simulated pre-fermented high-strength wastewater were investigated under different influent loading conditions. The results showed that when the influent chemical oxygen demand (COD), total nitrogen (TN), and orthophosphate (PO₄³⁻-P) concentrations in the SBR increased to 983, 56, and 20 mg/L, respectively, the COD removal efficiency was maintained above 85%, the TN removal efficiency was 64.5%, and the PO₄³⁻-P removal efficiency increased from 78.3% to 97.5%. Partial nitrification with simultaneous accumulation of ammonia (NH₄⁺-N) and nitrite (NO₂⁻-N) was observed, which may be related to the effect of high influent load on ammonia- and nitrite-oxidising bacteria. The biological phosphorus removal activity was higher when propionate was used as the carbon source instead of acetate. The relative abundance of glycogen accumulating organisms (GAOs) increased significantly with the increase in organic load, while Tetrasphaera was the consistently dominant polyphosphate accumulating organism (PAO) in the reactor. Under high organic loading conditions, there was no significant PAO–GAO competition in the reactor, thus the phosphorus removal performance was not affected.

Virucidal activity of microalgae extracts harvested during phycoremediation of swine wastewater

Phycoremediation of swine wastewater is a promising treatment since it efficiently removes nutrients and contaminants and, simultaneously, its biomass can be harvested and used to obtain a wide range of valuable compounds and metabolites. In this context, biomass microalgae were investigated for the phycoremediation of swine wastewater, and biomass extracts for its virucidal effect against enveloped and non-enveloped viruses. Microalgae were cultivated in a pilot scale bioreactor fed with swine wastewater as the growth substrate. Hexane, dichloromethane, and methanol were used to obtain the microalgae extracts. Extracts were tested for virucidal potential against HSV-1 and HAdV-5. Virucidal assays were conducted at temperatures that emulate environmental conditions (21 °C) and body temperature (37 °C). The maximum production of microalgae biomass reached a concentration of 318.5 ± 23.6 mg_DW L^-1. The results showed that phycoremediation removed 100% of ammonia-N and phosphate-P, with rates (k₁) of 0.218 ± 0.013 and 0.501 ± 0.038 (day^-1), respectively. All microalgae extract reduced 100% of the infectious capacity of HSV-1. The microalgae extracts with dichloromethane and methanol showed inhibition activities at the lowest concentration (3.125 µg mL^-1). Virucidal assays against HAdV-5 using microalgae extract of hexane and methanol inhibited the infectious capacity of the virus by 70% at all concentrations tested at 37 °C. At a concentration of 12.5 µg mL^-1, the dichloromethane microalgae extract reduced 50-80% of the infectious capacity of HAdV-5, also at 37 °C. Overall, the results suggest that the microalgae can be an attractive source of feedstock biomass for the exploration of alternative virucidal compounds.

Recovery of value-added products by mining microalgae

Microalgae blooms are always blamed for the interruption of the aquatic environment and pose a risk to the source of drinking water. Meanwhile, microalgae as primary producers are a kind of resource pool and could benefit the environment and contribute to building a circular economy. The lipid and polyhydroxybutyrate (PHB) in the cells of microalgae could be alternatives to fossil fuels and plastics, respectively, which are the culprits of global warming and plastic pollution. Besides, some microalgae are rich in nutrients, such as proteins and astaxanthin, which make themselves suitable for feed additives. As wastewater is rich in nutrients necessary for microalgae, thus, value-added product recovery via microalgae could be an approach to valorizing wastewater. However, a one-size-fits-all approach deploying various wastewater for the above products cannot be summarized. On the contrary, specific technical protocols should be tailored regarding each product in microalgae biomass with various wastewater. Thus, this review is to summarize the research effort by far on wastewater-cultivated microalgae for value-added products. Wastewater type, regulation methods, and targeted product yields are compiled and discussed and are expected to guide future extrapolation into a commercial scale.

Microalgae-based swine wastewater treatment: Strain screening, conditions optimization, physiological activity and biomass potential

Using microalgae to treat swine wastewater (SW) can achieve wastewater purification and biomass recovery at the same time. The algae species suitable for growth in SW were screened in this study, and the response surface combined with the desirability function method was used for multi-objective optimization to obtain high algal biomass and pollutant removal. Chlorophyll fluorescence parameters and biomass composition were analyzed to evaluate the cell physiological activity and its application potential. Chlorella sp. HL was selected as the most suitable species for growth in SW, and after 9 d of cultivation, the maximum specific growth rate and highest algal density were achieved 0.51 d^-1 and 2.43 × 10⁷ cells/mL, respectively. In addition, the removal of total phosphate and chemical oxygen demand were reached 69.13% and 72.95%, respectively. The optimum conditions for maximum algal density and highest pollutant removal were determined as the light intensity of 58.73 μmol/m²/s, inoculation density of 5.0 × 10⁶ cells/mL, and a light/dark ratio of 3 using response surface model, and the predicted overall desirability value was 0.96. The potential maximum quantum yield of PSII (Fv/Fm) of Chlorella sp. HL in the early stage of cultivation was 0.60-0.70, while under high light and long photoperiod, the value of Fv/Fm and performance index of Chlorella decreased, trapped and dissipated energy flux per reaction center increased. The higher heating value of 18.25 MJ/kg indicated that the Chlorella cultivated in SW could be a good feedstock for biofuel production.

Microbial fuel cells with Photosynthetic-Cathodic chamber in vertical cascade for integrated Bioelectricity, biodiesel feedstock production and wastewater treatment

This study aimed to develop efficient microbial fuel cells (MFCs) for integrated bioelectricity, biodiesel feedstock production and wastewater treatment. Among wastewaters tested, MFC fed with anaerobic digester effluent from rubber industry gave the maximum power density (55.43 ± 1.08 W/m³) and simultaneously removed COD, nitrogen and phosphorus (by 72.4 ± 0.9%, 40.5 ± 0.8% and 24.4 ± 1.5%, respectively). 16S rRNA gene analysis revealed that dominant microbial communities were: Firmicutes (43.68%), Bacteroidetes (25.41%) and Chloroflexi (15.02%), which mostly contributed to bioelectricity generation. After optimizing organic loading rate, photosynthetic oleaginous microalgae were applied in cathodic chamber in order to increase oxygen availability, secondarily treat anodic chamber effluent and produce lipids as biodiesel feedstocks. Four MFCs with photosynthetic-cathodic chamber connected in vertical cascade could improve power density up to 116.9 ± 15.5 W/m³, sequentially treat wastewater, and also produce microalgal biomass (465 ± 10 g/m³) with high lipid content (38.17 ± 0.01%). These strategies may greatly contribute to sustainable development of integrated bioenergy generation and environment.

Rice straw pretreatment using cow breeding wastewater for methane production

The aim of this study was to investigate the pretreatment of rice straw using cow breeding wastewater. The effects of filtering cow breeding wastewater through rice straw and microaerobic treatment on the pretreatment characteristics and methane production of rice straw were investigated. Generally, the filtration improved the pretreatment effect by adsorbing ammonium nitrogen and achieved higher solids loading for pretreatment. Although airtight treatment was optimal, the lignin removal and methane production of semi-sealed rice straw were only slightly lower than those of sealed rice straw. However, the results of open treatment were similar to those of the control. The maximum lignin removal and methane production reached 68.08% and 292.62 L/kg volatile solids (VS), respectively, for the filtered rice straw soaked in cow breeding wastewater again during pretreatment, and 61.26% and 274.18 L/kg VS, respectively, for the filtered rice straw pretreated directly without soaking.

Microalgal bioremediation of heavy metal pollution in water: Recent advances, challenges, and prospects

With the rapid economy development and population surge, the water resources available for direct use on the earth have been in shortage. Therefore, water pollution remediation inevitably becomes the focus of global attention. Aside from their capacity to fix and effectively control the emission of carbon dioxide thus achieve negative carbon emission, microalgae and its products modified by genetic engineering and other technologies also have a broad prospect in sewage treatment such as efficiently removing all kinds of pollutants in water and producing high-quality biofuels after use. Therefore, research on these organisms has gradually deepened in recent years. This paper summarizes the bioremediation mechanism of heavy metal ions in water by using microalgae and their modified products. The relevant research progresses since 2015 are critically reviewed and discussed. Challenges and prospects are also put forward for their industrial implementation.

Potential Application of Algae in Biodegradation of Phenol: A Review and Bibliometric Study

One of the most severe environmental issues affecting the sustainable growth of human society is water pollution. Phenolic compounds are toxic, hazardous and carcinogenic to humans and animals even at low concentrations. Thus, it is compulsory to remove the compounds from polluted wastewater before being discharged into the ecosystem. Biotechnology has been coping with environmental problems using a broad spectrum of microorganisms and biocatalysts to establish innovative techniques for biodegradation. Biological treatment is preferable as it is cost-effective in removing organic pollutants, including phenol. The advantages and the enzymes involved in the metabolic degradation of phenol render the efficiency of microalgae in the degradation process. The focus of this review is to explore the trends in publication (within the year of 2000-2020) through bibliometric analysis and the mechanisms involved in algae phenol degradation. Current studies and publications on the use of algae in bioremediation have been observed to expand due to environmental problems and the versatility of microalgae. VOSviewer and SciMAT software were used in this review to further analyse the links and interaction of the selected keywords. It was noted that publication is advancing, with China, Spain and the United States dominating the studies with total publications of 36, 28 and 22, respectively. Hence, this review will provide an insight into the trends and potential use of algae in degradation.

Cultivation and Biorefinery of Microalgae (Chlorella sp.) for Producing Biofuels and Other Byproducts: A Review

Microalgae-based carbon dioxide (CO2) biofixation and biorefinery are the most efficient methods of biological CO2 reduction and reutilization. The diversification and high-value byproducts of microalgal biomass, known as microalgae-based biorefinery, are considered the most promising platforms for the sustainable development of energy and the environment, in addition to the improvement and integration of microalgal cultivation, scale-up, harvest, and extraction technologies. In this review, the factors influencing CO2 biofixation by microalgae, including microalgal strains, flue gas, wastewater, light, pH, temperature, and microalgae cultivation systems are summarized. Moreover, the biorefinery of Chlorella biomass for producing biofuels and its byproducts, such as fine chemicals, feed additives, and high-value products, are also discussed. The technical and economic assessments (TEAs) and life cycle assessments (LCAs) are introduced to evaluate the sustainability of microalgae CO2 fixation technology. This review provides detailed insights on the adjusted factors of microalgal cultivation to establish sustainable biological CO2 fixation technology, and the diversified applications of microalgal biomass in biorefinery. The economic and environmental sustainability, and the limitations and needs of microalgal CO2 fixation, are discussed. Finally, future research directions are provided for CO2 reduction by microalgae.

Evaluation of growth and biochemical responses of freshwater microalgae Chlorella vulgaris due to exposure and uptake of sulfonamides and copper

Sulfonamides (SAs) and heavy metals are frequently detected together in livestock wastewater. In this study, evaluations regarding their potentially adverse effects on microalgae and according removals were investigated. Results showed that the growth of C. vulgaris was inhibited by SAs and Cu. There was an obvious recovery period in photosynthetic activity (Fv/Fm), indicating that the damage to the photosystem of microalgae was reversible. The co-existence of SAs and Cu significantly affected the biochemical characteristics, including the activities of antioxidant enzyme and the contents of photosynthetic pigments, proteins and polysaccharides. The addition of Cu obviously promoted the removal efficiencies of SMZ, SMX and SMM, which might be ascribed to the bridging effect of Cu in the bioadsorption of SAs. This study is conducive to understand the changes in the biochemical responses of microalgae under the combined impacts of SAs and Cu, and provides a new insight for the simultaneous removals.