Electrons transfer determined greenhouse gas emissions in enhanced nitrogen-removal constructed wetlands with different carbon sources and carbon-to-nitrogen ratios

Pollutant removal and greenhouse gas emissions in horizontal subsurface flow constructed wetlands with iron ore treating ammonium-rich wastewater

Horizontal subsurface flow constructed wetlands (HFCWs) are capable of eliminating organic matter and nitrogen while emitting less methane (CH4) and nitrous oxide (N2O) than free water surface flow wetlands. However, the simultaneous removal of pollutants and reduction of greenhouse gases (GHG) emissions from high-strength wastewater containing high levels of organic matter and ammonium nitrogen (NH4+-N) has not get been investigated. The influent COD concentration affected the efficiency of nitrogen removal, GHG emissions and the presence of iron from iron ore, but the COD and TP removal efficiencies remained unaffected. CO2 and CH4 fluxes were significantly influenced by influent COD concentrations, whereas less N2O emissions were obtained during 7d. The highest CO2 and CH4 fluxes, along with the GHG emissions, were observed in HFCWs with COD concentrations of 375.6 mg/L and NH4+-N concentrations of 159.0 mg/L at a COD/N ratio of 2.4. Conversely, the lowest CH4 (-1.72 mg/m2/h) and N2O fluxes (0.13 mg/m2/h) were recorded in HFCWs with COD concentrations of 375.6 mg/L and NH4+-N concentrations of 162.4 mg/L at a COD/N of 4.5, although nitrogen removal was weak in these HFCWs. HFCWs at a COD/N ratio of 3.6 exhibited greater removal of nitrogen and other pollutants, along with a lower global warming potential (GWP). In conclusion, the concentrations of organic matter and NH4+-N in wastewater affected both pollutant removal and GHG emissions. The simultaneous enhancement of pollutant removal and the reduction of GHG emissions can be achieved in HFCWs with a COD/N ratio of 3.6.

Reveling the micromolecular biological mechanism of acetate, thiosulfate and Fe0 in ecological floating beds for treating low C/N wastewater: Insight into nitrogen removals and greenhouse gases reductions

Selecting an appropriate electron donor to enhance nitrogen removal for treating low C/N wastewater in ecological floating beds (EFBs) is controversy. In this study, a systematic and comprehensive evaluation of sodium acetate (EFB-C), sodium thiosulfate (EFB-S) and iron scraps (EFB-Fe) was performed in a 2-year experiment on long-term viability including nitrogen removal and greenhouse gas emissions associated with key molecular biological mechanisms. The results showed that EFB-C (43-85 %) and EFB-S (40-88 %) exhibited superior total nitrogen (TN) removal. Temperature and hydraulic retention time (HRT) have significant impacts on TN removal of EFB-Fe, however, it could reach 86 % under high temperature (30-35 °C) and a long HRT (3 days), and it has lowest N2O (0-6.2 mg m-2 d-1) and CH4 (0-5.3 mg m-2 d-1) fluxes. Microbial network analysis revealed that the microbes changed from competing to cooperating after adding electron donors. A higher abundance of anammox genera was enriched in EFB-Fe. The Mantel's test and structural equation model provided proof of the differences, which showed that acetate and thiosulfate were similar, whereas Fe0 was different in the nitrogen removal mechanism. Molecular biology analyses further verified that heterotrophic, autotrophic, and mixotrophic coupled with anammox were the main TN removal pathways for EFB-C, EFB-S, and EFB-Fe, respectively. These findings provide a better understanding of the biological mechanisms for selecting appropriate electron donors for treating low C/N wastewater.

Optimizing nitrogen removal in constructed wetlands for low C/N ratio wastewater treatment: Insights from fermentation liquid utilization

The inefficient nitrogen removal in constructed wetlands (CWs) can be attributed to insufficient carbon sources for low carbon-to-nitrogen (C/N) ratio wastewater. In this study, sugarcane bagasse fermentation liquid (SBFL) was used as a supplemental carbon source in intermittently aerated CWs to enhance nitrogen removal. The impact of different regulated influent C/N ratios on nitrogen removal and greenhouse gas (GHG) emissions was investigated. Results demonstrated that SBFL addition significantly enhanced the denitrification capacity, resulting in faster NO3--N removal compared to sucrose. Moreover, intermittently aerated CWs significantly improved NH4+-N removal efficiency compared to non-aerated CWs. The highest total nitrogen removal efficiency (98.3 %) was achieved at an influent C/N ratio of 5 in intermittently aerated CWs with SBFL addition. The addition of SBFL resulted in a reduction of N2O emissions by 17.8 %-43.7 % compared to sucrose. All CWs exhibited low CH4 emissions, with SBFL addition (0.035-0.066 mg·m-2h-1) resulting in lower emissions compared to sucrose. Additionally, higher abundance of denitrification (nirK, nirS and nosZ) genes as well as more abundant denitrifying bacteria were shown in CWs of SBFL inputs. The results of this study provide a feasible strategy for applying SBFL as a carbon source to improve nitrogen removal efficiency and mitigate GHG emissions in CWs.

Mitigating nitrous oxide emissions from low carbon to nitrogen ratio wastewater treatment: Utilizing sugarcane bagasse fermentation liquid for constructed wetlands

Sugarcane bagasse was recycled to produce fermentation liquid (FL) as a supplementary carbon source that was added to constructed wetlands (CWs) for regulating influent carbon to nitrogen ratio (C/N), and then being applied to investigate nitrogen transformations and greenhouse gas emissions. Results showed that this FL achieved faster NO3--N removal and lower N2O fluxes than sucrose did, and the lowest N2O flux (67.6 μg m-2h-1) was achieved when FL was added to CWs in a C/N of 3. In contrast, CH4 emissions were higher by the FL addition than by the sucrose addition, although the fluxes under both additions were in a lower range of 0.06-0.17 mg m-2h-1. The utilization of FL also induced significant variations in microbial communities and increased the abundance of denitrification genes. Results showed the application of FL from sugarcane bagasse can be an effective strategy for improving nitrogen removal and mitigating N2O emissions in CWs.

Adding carbon sources to the substrates enhances Cr and Ni removal and mitigates greenhouse gas emissions in constructed wetlands

Constructed wetlands for wastewater treatment pose challenges related to long-term operational efficiency and greenhouse gas emissions on a global scale. This study investigated the impact of adding peat, humic acid, and biochar into the substrates of constructed wetlands and focused on Cr, and Ni removal, greenhouse gas emissions, and microbial communities in constructed wetlands. Biochar addition treatment achieved the highest removal efficiencies for total Cr (99.96%), Cr (VI) (100%), and total Ni (91.04%). Humic acid and biochar addition both significantly increased the heavy metal content in wetland plant Leersia hexandra and substrates of constructed wetlands. Further analysis of microbial community proportions by high-throughput sequencing revealed that biochar and humic acid treatments enhanced Cr and Ni removal efficiency by increasing the abundance of Bacteroidetes, Geobacter and Ascomycota. Humic acid addition treatment reduced CO2 emissions by decreasing the abundance of Bacteroidetes and increasing that of Basidiomycota. Peat treatment decreased CH4 emissions by reducing the abundance of the Bacteroidetes. Biochar treatment increased the abundance of the Firmicutes, Bacteroidetes, Proteobacteria as well as Basidiomycota, resulting in reduced N2O emissions. Biochar and humic acid treatments efficiently removed heavy metals from wastewater and mitigated greenhouse gas emissions in constructed wetlands by modifying the microbial communities.

Plant-microbe involvement: How manganese achieves harmonious nitrogen-removal and carbon-reduction in constructed wetlands

Carbon deficits in inflow frequently lead to inefficient nitrogen removal in constructed wetlands (CWs) treating tailwater. Solid carbon sources, commonly employed to enhance denitrification in CWs, increase carbon emissions. In this study, MnO2 was incorporated into polycaprolactone substrates within CWs, significantly enhancing NH4+-N and NO3--N removal efficiencies by 48.26-59.78 % and 96.84-137.23 %, respectively. These improvements were attributed to enriched nitrogen-removal-related enzymes and increased plant absorption. Under high nitrogen loads (9.55 ± 0.34 g/m3/d), emissions of greenhouse gases (CO2, CH4, and N2O) decreased by 147.23-202.51 %, 14.53-86.76 %, and 63.36-87.36 %, respectively. N2O emissions were reduced through bolstered microbial nitrogen removal pathways by polycaprolactone and MnO2. CH4 accumulation was mitigated by the increased methanotrophs and dampened methanogenesis, modulated by manganese. Additionally, manganese-induced increases in photosynthetic pigment contents (21.28-64.65 %) fostered CO2 sequestration through plant photosynthesis. This research provides innovative perspectives on enhancing nitrogen removal and reducing greenhouse gas emissions in constructed wetlands with polymeric substrates.

Soil amendments reduce CH4 and CO2 but increase N2O and NH3 emissions in saline-alkali paddy fields

Limited research has been conducted on ammonia (NH3) volatilization and greenhouse gases (GHGs) emissions in saline-alkali paddy fields, along with complex interaction involving various genes (16sRNA, amoA, narG, nirK, nosZ, and nifH). This study employed mesocosm-scale experiment to investigate NH3 volatilization and GHGs emissions, focusing on bacterial communities and genic abundance, in saline-alkali paddy fields with desulfurized gypsum (DG) and organic fertilizer (OF) amendments. Compared to the control (CK) treatment, DG and OF treatments reduced methane (CH4) and carbon dioxide (CO2) emissions by 78.05 % and 26.18 %, and 65.84 % and 11.62 %, respectively. However, these treatments increased NH3 volatilization by 26.26 % and 45.23 %, and nitrous oxide (N2O) emission by 41.00 % and 12.31 %. Notably, NH3 volatilization primarily stemmed from ammonia nitrogen (NH4+-N), rather than total nitrogen (TN) in soil and water. N2O was mainly produced from nitrate nitrogen (NO3--N) in soil and water, as well as NH4+-N in water. The increase in NH3 volatilization and N2O emission in DG and OF treatments, was attributed to the reduced competition among bacterial communities, rather than the increased bacterial activity and genic copies. These findings offer valuable insights for managing nutrient loss and gaseous emissions in saline-alkali paddy fields.

Enhanced adaptability of pyrite-based constructed wetlands for low carbon to nitrogen ratio wastewater treatments: Modulation of nitrogen removal mechanisms and reduction of carbon emissions

Pyrite-based constructed wetlands (CWs) stimulated nitrate removal performance at low carbon to nitrogen (C/N) ratio has been gaining widely attention. However, the combined effects of pyrite and C/N on the nitrate removal mechanisms and greenhouse gases (GHGs) reduction were ignored. This study found that pyrite-based CWs significantly enhanced nitrate removal in C/N of 0, 1.5 and 3 by effectively driving autotrophic denitrification with high abundance of autotrophs denitrifiers (Rhodanobacter) and nitrate reductase (EC 1.7.7.2), while the enhancement was weakened in C/N of 6 by combined effect of mixotrophic denitrification and dissimilatory nitrate reduction to ammonium (DNRA) with high abundance of organic carbon-degrading bacteria (Stenotrophobacter) and DNRA-related nitrite reductase genes (nrf). Moreover, pyrite addition significantly reduced GHGs emissions from CWs in all stages with the occurrence of iron-coupled autotrophic denitrification. The study shed light on the potential mechanism for pyrite-based CWs for treating low C/N ratio wastewater.

The performance, mechanism and greenhouse gas emission potential of nitrogen removal technology for low carbon source wastewater

Excessive nitrogen can lead to eutrophication of water bodies. However, the removal of nitrogen from low carbon source wastewater has always been challenging due to the limited availability of carbon sources as electron donors. Biological nitrogen removal technology can be classified into three categories: heterotrophic biological technology (HBT) that utilizes organic matter as electron donors, autotrophic biological technology (ABT) that relies on inorganic electrons as electron donors, and heterotrophic-autotrophic coupling technology (CBT) that combines multiple electron donors. This work reviews the research progress, microbial mechanism, greenhouse gas emission potential, and challenges of the three technologies. In summary, compared to HBT and ABT, CBT shows greater application potential, although pilot-scale implementation is yet to be achieved. The composition of nitrogen removal microorganisms is different, mainly driven by electron donors. ABT and CBT exhibit the lowest potential for greenhouse gas emissions compared to HBT. N2O, CH4, and CO2 emissions can be controlled by optimizing conditions and adding constructed wetlands. Furthermore, these technologies need further improvement to meet increasingly stringent emission standards and address emerging pollutants. Common measures include bioaugmentation in HBT, the development of novel materials to promote mass transfer efficiency of ABT, and the construction of BES-enhanced multi-electron donor systems to achieve pollutant prevention and removal. This work serves as a valuable reference for the development of clean and sustainable low carbon source wastewater treatment technology, as well as for addressing the challenges posed by global warming.

Application of alkali-heated corncobs enhanced nitrogen removal and microbial diversity in constructed wetlands for treating low C/N ratio wastewater

Lack of carbon source is the main limiting factor in the denitrification of low C/N ratio wastewater in the constructed wetlands (CWs). Agricultural waste has been considered as a supplementary carbon source but research is still limited. To solve this problem, ferric carbon (Fe-C) + zeolite, Fe-C + gravel, and gravel were used as substrates to build CWs in this experiment, aiming to investigate the effects of different carbon sources (rice straw, corncobs, alkali-heated corncobs) on nitrogen removal performance and microbial community structure in CWs for low C/N wastewater. The results demonstrated that the microbial community and effluent nitrogen concentration of CWs were mainly influenced by the carbon source rather than the substrate. Alkali-heated corncobs significantly enhanced the removal of NO2--N, NH4+-N, NO3-N, and TN. Carbon sources addition increased microbial diversity. Alkali-heated corncobs addition significantly increased the abundance of heterotrophic denitrifying bacteria (Proteobacteria and Bacteroidota). Furthermore, alkali-heated corncobs addition increased the copy number of nirS, nosZ, and nirK genes while greenhouse gas fluxes were lower than common corncobs. In summary, alkali-heated corncobs can be considered as an effective carbon source.

New insights into the effects of wetland plants on nitrogen removal pathways in constructed wetlands with low C/N ratio wastewater: Contribution of partial denitrification-anammox

Nitrogen (N) removal in constructed wetlands (CWs) was often challenged by limited denitrification due to the lack of carbon source, and wetland plants would be more important in carbon (C) and N cycling in CWs with influent of low carbon to nitrogen (C/N) ratio. In this study, the underlying mechanisms of nitrate nitrogen (NO3--N) removal under different low C/N ratios were revealed by constructing microcosm CWs, and the unplanted group was set as the control to explore the role of plants in N removal. The results showed that plants and the concentration of influent carbon significantly affected NO3--N and total nitrogen (TN) removal (p < 0.05). The presence of plants significantly increased the concentration of DO and wetland plant-derived DOM (p < 0.05). The enhanced NO3--N and TN removal with increased C/N ratio attributed to high denitrification activity reflected in the abundance of denitrification microbes and genes. However, the contribution of partial denitrification-anammox (PDN/AMX) to N removal in CWs decreased from more than 75.3% at the C/N ratio of 0 to 70.4% and 22.3% with the C/N ratio increased to 1.5 and 3, respectively. Furthermore, the PDN/AMX process was negatively correlated with favorable oxygen environment in the planted group and plants roots carbon secretion, but the overall N removal efficiency of the CWs was enhanced by increased abundance of N removal-related functional genes in the presence of plants. Abovementioned results provided new insights to explain the mechanism of N removal in CWs under low C/N ratio.

Microalgae-based constructed wetland system enhances nitrogen removal and reduce carbon emissions: Performance and mechanisms

Combination of constructed wetlands (CWs) and microalgae-based technologies has been proved as effective wastewater treatment option; however, little attention was paid to investigate the optimal combination ways. This study showed that the integrated system (IS) connecting microalgal pond with CWs exhibited improved pollutant-removal efficiencies and preferred carbon reduction effects compared to other alternatives such as coupled system or independent CWs. Microbial analysis demonstrated that core microorganisms (e.g., Acinetobacter and Thermomonas) of the IS were mostly associated with carbon, nitrogen, and energy metabolism. Based on co-occurrence networks, microbial quantity with denitrification function in the IS accounted for 71.01 % of the microorganism related to nitrogen metabolism, which was higher than that of 48.84 % in the independent CWs, indicating that the presence of microalgae in IS played important role in promoting biological denitrification. These findings provide insights into the microbial mechanism and highlights the complementary effects between microalgae and CWs.

Microbial response to nitrogen removal driven by combined iron and biomass in subsurface flow constructed wetlands with plants of different ages

This study investigated the nitrogen removal enhanced by combined iron scraps and plant biomass, and its microbial response in the wetland with different plant ages and temperatures. The results showed that older plants benefitted the efficiency and stability of nitrogen removal, which could reach 1.97 ± 0.25 g m^-2 d^-1 in summer and 0.42 ± 0.12 g m^-2 d^-1 in winter. Plant age and temperature were the main factors determining the microbial community structure. Compared with temperature, plant ages affected more significantly on relative abundance of microorganisms such as Chloroflexi, Nitrospirae, Bacteroidetes and Cyanobacteria, and functional genera for nitrification (e.g., Nitrospira) and iron reduction (e.g., Geothrix). The absolute abundance of total bacterial 16S rRNA ranged from 5.22 × 10⁸ to 2.63 × 10⁹ copies g^-1 and presented extremely significant negative correlation to plant age, which would lead to a decline in microbial function on information storage and processing. The quantitative relationship further revealed that the ammonia removal was related to 16S rRNA and AOB amoA, while nitrate removal was controlled by 16S rRNA, narG, norB and AOA amoA jointly. These findings suggested that a mature wetland for nitrogen removal enhancement should focus on aging microbes caused by old plants and possible endogenous pollution.

New insights into hexavalent chromium exposure in electron donor limited denitrification: bio-electron behavior

The bio-electron behavior (electron production, transmission, and consumption) response to a typical heavy metal, hexavalent chromium, was unraveled in the electron donor limited system (EDLS) and electron donor sufficient system (EDSS). Nicotinamide adenine dinucleotide and adenosine triphosphate production were reduced by 44% and 47%, respectively, due to glucose metabolism inhibition, leading to NO₃^--N declining to 31% in EDLS. The decreased electron carrier contents and denitrifying enzymes activity inhibited electron transmission and consumption in both EDLS and EDSS. Additionally, electron transfer and antioxidant stress abilities were reduced, further hindering the survival of denitrifiers in EDLS. The lack of dominant genera (Comamonas, Thermomonas, and Microbacterium) in EDLS was the primary reason for poor biofilm formation and chromium adaptability. The decreased expression of enzymes related to glucose metabolism caused the imbalance of electron supply, transport, and consumption in EDLS, adversely impacting nitrogen metabolism and inhibiting denitrification performance.

Carbon source recovery from waste sludge reduces greenhouse gas emissions in a pilot-scale industrial wastewater treatment plant

Carbon cycle regulation and greenhouse gas (GHG) emission abatement within wastewater treatment plants (WWTPs) can theoretically improve sustainability. Currently, however, large amounts of external carbon sources used for deep nitrogen removal and waste sludge disposal aggravate the carbon footprint of most WWTPs. In this pilot-scale study, considerable carbon was preliminarily recovered from primary sludge (PS) through short-term (five days) acidogenic fermentation and subsequently utilized on-site for denitrification in a wool processing industrial WWTP. The recovered sludge-derived carbon sources were excellent electron donors that could be used as additional carbon supplements for commercial glucose to enhance denitrification. Additionally, improvements in carbon and nitrogen flow further contributed to GHG emission abatement. Overall, a 9.1% reduction in sludge volatile solids was achieved from carbon recovery, which offset 57.4% of external carbon sources, and the indirect GHG emissions of the target industrial WWTP were reduced by 8.05%. This study demonstrates that optimizing the allocation of carbon mass flow within a WWTP has numerous benefits.

Effect of low temperature on contributions of ammonia oxidizing archaea and bacteria to nitrous oxide in constructed wetlands

Constructed wetlands (CWs) have been widely used for ecological remediation of micro-polluted source water. Nitrous oxide (N₂O) from CWs has caused great concern as a greenhouse gas. However, the contribution of ammonia oxidation driven by ammonia oxidizing archaea (AOA) and ammonia oxidizing bacteria (AOB) to N₂O emission, especially at low temperature, was unknown. This study aimed to quantify the contributions of AOA and AOB to N₂O through lab-scale subsurface CWs. The N₂O emission flux of CW at 8 °C was 1.23 mg m^-2·h^-1, significantly lower than that at 25 °C (1.92 mg m^-2·h^-1). The contribution of ammonia oxidation to N₂O at 8 °C (33.04%) was significantly higher than that at 25 °C (24.17%). The N₂O production from AOA increased from 1.91 ng N·g^-1 at 25 °C to 4.11 ng N·g^-1 soil at 8 °C and its contribution increased from 23.38% to 30.18% (P < 0.05). Low temperature impaired functional gene groups and inhibited the activity of AOB, resulting in its declined contribution. Based on the transcriptional analysis, AOA was less affected by low temperature, thus stably contributing to N₂O. Moreover, community diversity and relationships of AOA were enhanced at 8 °C, while AOB declined. The results confirmed the significant contribution of AOA and demonstrated molecular mechanisms (higher activity and community stability) of the increased contribution of AOA to N₂O at low temperature.

Impact of soluble organic matter and particulate organic matter on anammox system: Performance, microbial community and N2O production

In this study, the effects of soluble readily biodegradable COD (sCOD) and particulate slowly biodegradable COD (pCOD) on anammox process were investigated. The results of the long-term experiment indicated that a low sCOD/N ratio of 0.5 could accelerate the anammox and denitrification activity, to reach as high as 84.9%±2.8% TN removal efficiency. Partial denitrification-anammox (PDN/anammox) and denitrification were proposed as the major pathways for nitrogen removal, accounting for 91.3% and 8.7% of the TN removal, respectively. Anammox bacteria could remain active with high abundance of anammox genes to maintain its dominance. Candidatus Kuenenia and Thauera were the predominant genera in the presence of organic matter. Compared with sCOD, batch experiments showed that the introduction of pCOD had a negative effect on nitrogen removal. The contribution of denitrification to nitrogen removal decreased from approximately 14% to 3% with increasing percentage of pCOD. In addition, the analysis result of the process data using an optimized ASM1 model indicated that high percentage of pCOD resulted in serious N₂O emission (the peak value up to 0.25 mg N/L), which was likely due to limited mass diffusion and insufficient available carbon sources for denitrification. However, a high sCOD/N ratio was beneficial for alleviating N₂O accumulation.

Nitrogen Removal Characteristics of a Marine Denitrifying Pseudomonas stutzeri BBW831 and a Simplified Strategy for Improving the Denitrification Performance Under Stressful Conditions

A marine aerobic denitrifying bacterium was isolated and identified as Pseudomonas stutzeri BBW831 from the seabed silt of Beibu Gulf in China. According to the genome analysis, P. stutzeri BBW831 possessed a total of 14 genes (narG, narH, narI, narJ, napA, napB, nirB, nirD, nirS, norB, norC, norD, norQ, and nosZ) responsible for fully functional enzymes (nitrate reductase, nitrite reductase, nitric oxide reductase, and nitrous oxide reductase) involved in the complete aerobic denitrification pathway, suggesting that it had the potential for reducing nitrate to the final N₂. Denitrification results showed that P. stutzeri BBW831 exhibited efficient nitrogen removal characteristics. Within 12 h, the NO₃^--N removal efficiency and rate reached 94.64% and 13.09 mg·L^-1·h^-1 under 166.10 ± 3.75 mg/L NO₃^--N as the sole nitrogen source, and removal efficiency of the mixed nitrogen (50.50 ± 0.55, 62.28 ± 0.74, and 64.26 ± 0.90 mg/L of initial NH₄⁺-N, NO₃^--N, and NO₂^--N, respectively) was nearly 100%. Furthermore, a simplified strategy, by augmenting the inoculation biomass, was developed for promoting the nitrogen removal performance under high levels of NO₂^--N and salinity. As a result, the removal efficiency of the initial NO₂^--N up to approximately 130 mg/L reached 99.46% within 8 h, and the NO₃^--N removal efficiency achieved at 59.46% under the NaCl concentration even up to 50 g/L. The C/N ratio of 10 with organic acid salt such as trisodium citrate and sodium acetate as the carbon source was most conducive for cell growth and nitrogen removal by P. stutzeri BBW831, respectively. In conclusion, the marine P. stutzeri BBW831 contained the functional genes responsible for a complete aerobic denitrification pathway (NO₃^--N → NO₂^--N → NO → N₂O → N₂), and had great potential for the practical treatment of high-salinity nitrogenous mariculture wastewater.

Socio-ecological well-being perspectives of wetland loss scenario: A review

Previous original research focused on wetland loss and finding out its drivers across different regional units of the world. A few reports also tried to account world's condition on wetland loss. A couple of review articles articulated the causes of wetland loss and services. The present study intended to explore the linkage between wetland loss rate and processes concerning socio-ecological well-being parameters to highlight alternative ways to adopt wetland conservation policies. A total of 132 pieces of Scopus index literature were taken analysing loss rate and drivers of loss from 22 sample countries where publication frequency is relatively high. Meta-analysis was done to explain the publication trend and spatial change in publication polarity. Results distinctly revealed that the rate of wetland loss varies from 0.06% to 4.81% annually, with substantially low in developed countries (DC) than in developing (DeV) and least developed countries (LDC). Six drivers, such as agricultural land expansion, the built-up area, the conversion to grassland area, construction of the dam, climate change and tourism, were the primary drivers. But all these are not equally active across the DC, DeV and LDC. Climate change, tourism development in DC, agriculture and built-up expansions in the Dev and LDC appeared as the major causes behind wetland loss. Socio-ecological well-being parameters like human development, environmental performance, social progression, and economic status were found to be significantly negatively (-0.48 to -0.57), and the poverty rate was positively (0.27) associated with the rates of wetland loss. Drivers also varied with respect to the socio-ecological conditions. These findings are not merely added knowledge to the state-of-arts but are also helpful in re-directing global policies toward wetland conservation.

Quantifying biochar-induced greenhouse gases emission reduction effects in constructed wetlands and its heterogeneity: A multi-level meta-analysis

Zero-waste biochar is an emerging tool for carbon neutralization, but the role of biochar in reducing greenhouse gases (GHGs) emissions from CWs were controversy and uncertainty. Yet, no previous study has integrated multiple research systems to quantitatively examine biochar-mediated GHGs emission reduction potential in CWs. Here we synthesized 114 studies to quantify biochar-induced declines ability of GHGs in the CWs by using the multi-level meta-analysis, reveal the variation of GHGs emission effect in different biochar-CWs and its response relationship with biochar, and identify the moderating variables that had a strong explanatory effect on the emission reduction effect of biochar. We showed that biochar remarkably affect CO₂ mitigation (p < 0.05), but has insignificant and heterogeneous effects on CH₄ and N₂O. Pyrolysis time, influent dissolved oxygen (DO), influent NO₃^--N concentration, hydraulic retention time (HRT) and wetland type can significantly affect the effect of biochar on CH₄ emission reduction. Particularly, the importance of HRT and wetland type was 0.89 and 0.85, respectively. Specially, the surface batch CWs modified by biochar could significantly promote the emission of CH₄ (p < 0.001), and the effect size was up to 89.59. For N₂O, biochar diameter, biochar addition ratio, influent COD/TN ratio, plant name, and removal efficiency of NO₃^--N/TN/COD were significant moderators. Among them, influent COD/TN ratio and plant name showed a stronger explanation. Planting Cyperus alternifolius L. significantly enhanced the N₂O emission reduction capacity by biochar (p < 0.001), and effect size was as low as -24.32. 700-900 °C biochar can promote CH₄ flux but inhibit N₂O flux. This study provides an important theoretical basis and valuable strategic guidance for more accurate estimation and improvement of synergistic emission reduction benefits between CH₄ and N₂O of biochar in CWs.

Microbial response mechanism of plants and zero valent iron in ecological floating bed: Synchronous nitrogen, phosphorus removal and greenhouse gas emission reduction

Iron-based ecological floating beds (EFBs) are often used to treat the secondary effluent from wastewater treatment plant to enhance the denitrification process. However, the impact and necessity of plants on iron-based EFBs have not been systematically studied. In this research, two iron-based EFBs with and without plants (EFB-P and EFB) were performed to investigate the response of plants on nutrient removal, GHG emissions, microbial communities and functional genes. Results showed the total nitrogen and total phosphorus removal in EFB-P was 45-79% and 48-72%, respectively, while that in EFB was 31-67% and 44-57%. Meanwhile, plants could decrease CH₄ emission flux (0-3.89 mg m^-2 d^-1) and improve CO₂ absorption (4704-22321 mg m^-2 d^-1). Plants could increase the abundance of Nitrosospira to 1.6% which was a kind of nitrifying bacteria dominant in plant rhizosphere. Among all denitrification related genera, Simplicispira (13.08%) and Novosphingobium (6.25%) accounted for the highest proportion of plant rhizosphere and iron scrap, respectively. Anammox bacteria such as Candidatus_Brocadia was more enriched on iron scraps with the highest proportion was 1.21% in EFB-P, and 2.20% in EFB. Principal co-ordinates analysis showed that plants were the critical factor determining microbial community composition. TN removal pathways were mixotrophic denitrification and anammox in EFB-P while TP removal pathways were plant uptake and phosphorus-iron coprecipitation. In general, plants play an important directly or indirectly role in iron-based EFBs systems, which could not only improve nutrients removal, but also minimize the global warming potential and alleviate the greenhouse effect to a certain extent.

Enhanced performance and microbial interactions of shallow wetland bed coupling with functional biocathode microbial electrochemical system (MES)

It is essential to remediate the polluted urban river, which endangers the aquatic creatures and affected human body's senses. The treatment wetland combined with microbial electrochemical system (MES) used for the remediation is becoming a new research focus due to its ideal pollutants removal efficiency and small footprint. Here this paper provided a kind of novel shallow wetland bed coupling with close-circuit microbial electrochemical system (WB-CMES) to remove pollutants in surface water. In contrast to the shallow wetland bed coupling with open-circuit MES (WB-OMES) and the shallow wetland bed without MES (WB), the enhancing effects and pollutants removal pathway were evaluated. After 62-day operation, average TN removal efficiency in WB-CMES was 87.7%, which was 19.7% and 13.8% higher than that of WB-OMES and WB respectively. The rate coefficient k of NO₃^--N degradation in WB-CMES was 1.6 and 1.8 times higher than that in WB-OMES and WB. The results of chlorophyll, protein and superoxide dismutase (SOD) in WB-CMES were 27.3%, 44.3% and 12.9% higher than those in WB. The microbial community structure analysis indicated that electroactive bacteria on anode like Desulfobulbus could oxidize organics and generate electrons to compensate cathode, meanwhile, cathode could enrich more species of functional bacteria like Rhodobacter, Pirellula, Hyphomicrobium, Thauera, which had a synergistic effect on oxygen reduction, nitrogen removal and plant growth. The results indicated that oxygen produced by submerged plants could be utilized by the oxygen-reducing functional biocathode of MES and the proper aerobic and anoxic environment might enhance nitrate removal mainly through simultaneous nitrification and denitrification (SND), aerobic denitrification and anammox. This research provided a novel technology with advantages of simple operation, flexible configuration, easy scale-up and low cost for application in remediation of highly polluted surface water.

Cold temperature mediated nitrate removal pathways in electrolysis-assisted constructed wetland systems under different influent C/N ratios and anode materials

Electrolysis had proven to be useful for the enhanced performance in constructed wetlands (CWs). While at cold temperature, the nitrate removal pathways, plant physiological characteristics and microbial community structure in electrolysis-assisted CWs were unclear. Therefore, the purification performance of three electrolysis-assisted horizontal subsurface-flow constructed wetlands (E-HSCWs) with different anodes and a control system in cold seasons were evaluated in this study. E-HSCWs showed a 2.02-83.21% increase of total nitrogen (TN) removal when compared to control, and the gaps were enlarged with increasing C/N (chemical oxygen demand/total nitrogen, COD/TN) ratios. Nitrite accumulation in E-HSCWs presented a first increase then went down trend with increasing C/N ratios, compared to a steady increase in control system. The optimum C/N ratio was 8 in E-HSCWs for both TN and COD removal. Moreover, Ti|IrO₂-Ta₂O₅ (Ti) anode showed the highest potential for TN and COD removal. Less root weight, shorter root length and reduced TN and total phosphorus (TP) contents in roots were observed in wetland plants (Iris sibirica) of E-HSCWs. In E-HSCWs with Fe and C anodes, the nitrate removal was mainly accomplished by autotrophic denitrifier Hydrogenophaga. While in E-HSCWs with Ti anode, the synergistic effect of autotrophic denitrifier Hydrogenophaga and heterotrophic denitrifiers Acidovorax, Simplicispira, Zoogloea accounted for the nitrate removal. These results showed that E-HSCWs at proper C/N ratio of 8 would be promising for nitrate removal at cold temperature.

Effects of substrate type on variation of sludge organic compounds, bioelectric production and microbial community structure in bioelectrochemically-assisted sludge treatment wetland

A bioelectrochemical assisted sludge treatment wetland (BE-STW) is a promising technology used in the elimination of organic compounds and recovery of bio-energy. In this study, four BE-STW systems were constructed to investigate the effects of some substrates (i.e. graphite particles, zeolite, ceramsite, and gravel) on organic compounds biodegradation and transformation, electricity production, and anodic bacterial community. The maximum output voltages were 0.939, 0.870, 0.741 and 0.835 V, and the maximum power densities were 0.467, 0.143, 0.110, and 0.131 W/m³ for the graphite particles (BS-GP), zeolite (BS-Z), ceramsite (BS-C), and gravel (BS-G) systems, respectively. Also, the dissolved organic carbon (DOC) removal rates were 61.84%, 28.54%, 25.56%, and 18.34% in BS-GP, BS-G, BS-Z, and BS-C, respectively. The degradation of aromatic compounds in sludge extracellular biological organic matter (EBOM) was mainly due to the decrease of hydrophilic fraction (HPI) and transphilic acid fraction (TPI-A) contents. Moreover, aromatic proteins were preferentially removed in BS-Z. For BS-C, the tyrosine-like proteins and humic acid-like substances in TPI-A were totally removed. An excitation-emission matrix (EEM) analysis showed that the fluorescent intensity of the humic acid-like substances was the lowest in BS-GP, and no fluorescence peaks of fulvic acid-like substances were observed. Finally, at the genus level, Longilinea, Terrimonas, Ottowia, and Saccharibacteria_genera_incertae_sedis were the dominant bacteria in BE-STW, and Methylophilus was also only detected in BS-GP. These results confirmed that substrate materials have a significant impact on the preferentially degraded organic matter in BE-STWs, which can provide a theoretical basis for the practical application of STW in the future.

Food waste hydrolysate as a carbon source to improve nitrogen removal performance of high ammonium and high salt wastewater in a sequencing batch reactor

The high ammonium and high salt (HAHS) wastewater generated from the anaerobic digestate of food waste is usually difficult to be treated by biological process because of its low C/N ratio. Herein, food waste hydrolysate (FWH) is rich in readily biodegradable organic matter, was utilized as carbon source to enhance the nitrogen removal of HAHS in the activated-sludge system. Results showed that compared with the control average total nitrogen removal efficiency increased from 73.4% to 94.9% and effluent declined from 281.4 mg/L to 53.9 mg/L by adding FWH at the C/N ratio of 6, satisfying the sewage discharge standard regulated by China. Besides, FWH utilization led to higher selectivity of the species responsible for nitrogen removal in related to glucose-adding group, which were dominated by Flavobacteriaceae, Melioribacteraceae, PHOS-HE36, and Rhodobacteraceae after a long-term operation. In general, FWH is an alternative carbon source to enhance nitrogen removal in HAHS wastewater treatment.

Nitrate removal under low carbon to nitrogen ratio by modified corn straw bioreactor: Optimization and possible mechanism

ABSTRACTThe removal of nitrate (NO₃^--N) from water bodies under the conditions of poor nutrition and low carbon to nitrogen (C/N) ratio is a widespread problem. In this study, modified corn stalk (CS) was used to immobilize Burkholderia sp. CF6 with cellulose-degrading and denitrifying abilities. The optimal operating parameters of the bioreactor were explored. The results showed that under the hydraulic retention time (HRT) of 3 h and the C/N ratio of 2.0, the maximum nitrate removal efficiency was 96.75%. In addition, the organic substances in the bioreactor under different C/N ratios and HRT were analyzed by three-dimensional fluorescence excitation-emission mass spectrometry (3D-EEM), and it was found that the microorganisms have high metabolic activity. Scanning electron microscope (SEM) showed that the new material has excellent immobilization effects. Fourier transform infrared spectrometer (FTIR) showed that it has potential as a solid carbon source. Through high-throughput sequencing analysis, Burkholderia sp. CF6 was observed as the main bacteria present in the bioreactor. These research results showed that the use of waste corn stalks waste provides a theoretical basis for the advanced treatment of low C/N ratio wastewater.

Effects and mechanisms of constructed wetlands with different substrates on N2O emission in wastewater treatment

Nitrous oxide (N₂O) emissions from constructed wetlands (CWs) are accompanying problems and have attracted much attention in recent years. CWs filled with different substrates (gravel, biochar, zeolite, and pyrite) were constructed to investigate the nitrogen removal performance and N₂O emissions, which named C-CWs, B-CWs, Z-CWs, and P-CWs, respectively. C-CWs showed the poorest nitrogen removal performance in all CWs. Although B-CWs exhibited the highest fluxes of N₂O emissions, the percentage of N₂O emissions in nitrogen removal (0.15%) was smaller than that of C-CWs (0.18%). In addition, microbiological analysis showed that compared with C-CWs, CWs filled with biochar, zeolite, and pyrite had higher abundance of nitrifying and denitrifying microorganisms and lower abundance of N₂O producing bacteria. In conclusion, biochar, zeolite, and pyrite were more favorable kinds of substrate than the conventional substrates of gravel for the nitrogen removal and reduction of N₂O emissions from CWs.

Efficient vanillin biosynthesis by recombinant lignin-degrading bacterium Arthrobacter sp. C2 and its environmental profile via life cycle assessment

Vanillin is a natural flavoring agent that is widely used in the bioengineering industry. To enable sustainable development, joint consideration of bacterial performance and negative environmental impacts are critical to vanillin biosynthesis. In this study, a cold shock protein (csp) gene was upregulated for maintaining stable growth in Arthrobacter sp. C2 responding to vanillin and cold stress. Furthermore, the recombinant strain C2 was constructed by simultaneously deleting the xylC gene encoding benzaldehyde dehydrase and overexpressing the pchF gene encoding vanillyl alcohol oxidase and achieved a maximum vanillin productivity of 0.85 mg/g DCW/h with alkaline lignin as the substrate. Finally, this process generated an environmental impact value of 25.05, which was the lowest environmental impact achieved according to life cycle assessment (LCA). Improvement strategies included reducing electricity consumption and replacing chemicals. This study achieved the development of an effective strategy, and future studies should focus on precise vanillin biosynthesis methods for large-scale application.

Efficient utilization of Iris pseudacorus biomass for nitrogen removal in constructed wetlands: Combining alkali treatment

Aquatic plant biomass like Iris pseudacorus can be used as electron donor to improve denitrification performance in subsurface constructed wetlands. However, the phenomenon that the nitrogen removal rate declined in the terminal stage restricted the utilization of litters. In terms of this problem, this study investigated the performance of the used biomass through alkali treatment on nitrogen removal and analyzed the effect of alkali treatment on the component and structure of biomass and microbial community. The results showed that the alkali-treated biomass could further enhance the nitrogen removal by nearly 15% compared with used ones. The significant damage of cell walls and compact fibers containing cellulose and lignin through alkali treatment mainly resulted in the improvement of carbon release and nitrogen removal. With the addition of alkali-treated biomass, the richness index of microbes was higher compared with other biomass materials. Furthermore, the abundance of denitrification related genera increased and the abundance of genera for nitrification was maintained. Based on these finds, a mode of a more efficient Iris pseudacorus self-consumed subsurface flow constructed wetlands was designed. In this mode, the effluent total nitrogen could be stabilized below 5 mg L^-1 for nine months and the weight of litters could be further cut down by 75%. These findings would contribute to efficient utilization of plant biomass for nitrogen removal enhancement and final residue reduction in the wetlands.

New insights in correlating greenhouse gas emissions and microbial carbon and nitrogen transformations in wetland sediments based on genomic and functional analysis

Greenhouse gas (GHG) emissions from constructed wetlands (CWs) lower the environmental and ecological benefits of CWs and thus have raised increasing environmental concern. To prevent GHGs emissions, it is important to assess and quantify the correlation of GHGs emission and microbial carbon and nitrogen transformations. In this study, two typical wetland substrate samples (mud sampled from Xiaomei River CW and sand sampled from Dongwen River CW) were used to build lab-scale vertical subsurface flow CW microcosms, labeled as XRCW and DRCW, respectively. The mean COD removal rate of the DRCW group (76.1%) was higher than that of XRCW group (60.6%). Both groups achieved a high extent of nitrogen nutrient removal, indicating a higher metabolic activity of nitrifying and denitrifying microorganisms in the system, especially in XRCW. The mean emission fluxes of N₂O, CH₄ and CO₂ in the XRCW group were 52.7 μg/m²-h, 1.6 mg/m²-h and 100.4 mg/m²-h, which were higher than that in the DRCW group (30.0 μg/m²-h, 1.0 mg/m²-h and 28.0 mg/m²-h, respectively). The relation of GHG emissions to microbial carbon and nitrogen transformation was assessed by genomics and functional analysis. The release of GHGs by the XRCW group had a positive correlation with the relative abundance of Proteobacteria, while for the DRCW group a positive correlation was found with the relative abundance of Cyanobacteria. Nitrogen fixation by Cyanobacteria could be an approach to reduce GHG emissions. The release of CH₄ and CO₂ was positively correlated with glucose metabolism. N₂O gas emission was affected by the species of denitrifiers. This study is of great importance to clarify the emissions of GHGs in vertical subsurface flow CWs, as it is relating to microbial carbon and nitrogen transformation. The connection is of great significance to control the emission of GHGs in wetlands.

Comprehensive evaluation of manganese oxides and iron oxides as metal substrate materials for constructed wetlands from the perspective of water quality and greenhouse effect

Manganese oxides and iron oxides have been widely introduced in constructed wetlands (CWs) for sewage treatment due to their extensiveness in nature and their ability to participate in various reactions, but their effects on greenhouse gas (GHG) emissions remain unclear. Here, a set of vertical subsurface-flow CWs (Control, Fe-VSSCWs, and Mn-VSSCWs) was established to comprehensively evaluate which are the better metal substrate materials for CWs, iron oxides or manganese oxides, through water quality and the global warming potential (GWP) of nitrous oxide (N₂O), methane (CH₄), and carbon dioxide (CO₂). The results revealed that the removal efficiencies of chemical oxygen demand (COD), total nitrogen (TN), and total phosphorus (TP) in Mn-VSSCWs were all higher than that in Fe-VSSCWs, and manganese oxides could almost completely suppress the CH₄ production and reduce GWP (from 8.15 CO₂-eq/m²/h to 7.17 mg CO₂-eq/m²/h), however, iron oxides promoted GWP (from 8.15 CO₂-eq/m²/h to 10.84 mg CO₂-eq/m²/h), so manganese oxides are the better CW substrate materials to achieve effective sewage treatment while reducing the greenhouse gas effect.

Pseudomonas stutzeri GF2 augmented the denitrification of low carbon to nitrogen ratio: Possibility for sewage wastewater treatment

A denitrifying strain with high efficiency at low carbon to nitrogen (C/N) ratio of 2.0 was isolated and characterized. It belongs to the genus Pseudomonas. Scanning electron microscopy (SEM) showed that GF2 was rod-shaped. The nitrate removal efficiency reached up to 92.41% (1.85 mg L^-1 h^-1) with the C/N ratio of 2.0 and the nitrite accumulation eventually decreased to 0.88 mg L^-1. By response surface method (RSM) method, three reaction conditions of strain GF2 were optimized, including pH, C/N ratio, and nitrate concentration. Nitrogen balance and gas detection revealed that 88.03% of nitrogen was removed in gaseous form (included 98.80% nitrogen gas), which confirmed its efficient denitrification ability and pathway. 3D fluorescence spectrum (3D-EEM) manifested that in the absence of organic matter, strain GF2 can utilize extracellular polymeric substance (EPS) as carbon source for efficient denitrification. This research strived to provide new research ideas for low C/N ratio sewage treatment.

Impact of C/N ratio on the fate of simultaneous Ca2+ precipitation, F- removal, and denitrification in quartz sand biofilm reactor

The coexistence of F^-, Ca²⁺, nitrates, and other pollutants in water body has aroused widespread concern. In this research, a novel quartz sand biofilm reactor was established, aiming to study the key factors of different carbon to nitrogen (C/N) ratios (5:1, 4:1, and 3:1), initial Ca²⁺ concentration (180 mg L^-1, 144 mg L^-1, and 108 mg L^-1), and hydraulic retention time (HRT) (4 h, 6 h, and 8 h) on simultaneous Ca²⁺ precipitation, F^- removal, and denitrification. Results showed that the removal efficiencies of Ca²⁺, F^-, and nitrate were 55.04%, 82.64%, and 97.69% under the low C/N ratio of 3:1, initial Ca²⁺ concentration of 180 mg L^-1, and HRT of 8 h. 3-D Excitation-Emission Fluorescence Spectroscopy (3-D EEM) demonstrates that extracellular polymeric substances (EPS) was generated during the growth metabolism. Scanning Electron Microscopy (SEM) and X-ray diffractometer images showed that Ca²⁺, F^- removed in the form of CaCO₃, Ca₅(PO₄)₃F and CaF₂ under Acinetobacter sp. H12 induction. Moreover, high-throughput sequencing results display that the biomineralized bacteria Acinetobacter sp. H12 exerted great influence in the bioreactor. This research will underpin the practical use of multiple pollutants such as F^- and Ca²⁺ wastewater under the different C/N ratios.

Higher nitrogen removal achieved in constructed wetland with polyethylene fillers and NaOH-heating pre-treated corn stalks for advanced treatment of low C/N sewage

Advanced processing of low C/N sewage faces the carbon sources shortage, while quantities of agricultural biomass wastes need to be disposed. This study investigated the potential of quantitative modified biomass addition in constructed wetlands (CWs) filled with polyethylene fillers. Results showed that the lignin in NaOH-heating pretreated corn stalks (NH-CSs) was destroyed, and the wrinkles on the stalks increased and became more soft after pretreatment, which was more conducive to the utilization of carbon sources and attachment of microorganisms. Compared with glucose and sodium acetate, the denitrification with mixed carbon source (glucose and NH-CSs) had the highest effective utilization percentage (61.37%) and NH-CSs were expected to become stable and fast-release carbon sources. After adding 30 g NH-CSs to the rear unit of CW with polyethylene fillers (CW-A), TN removal efficiency was increased by 18.21%, and the average removal efficiency of COD, NH₄⁺-N, TN, and TP reached 54.83%, 89.95%, 64.11%, and 45.04%, respectively. Compared with the traditional CW (CW-B), CW-A had a significant denitrification advantage (P < 0.05), but the removal efficiency and effluent stability of phosphorus were inferior to CW-B. These results indicate that the biomass carbon sources such as corn stalks and polyethylene fillers have a good potential to improve the denitrification in CWs.

Removal of sulfamethoxazole and tetracycline in constructed wetlands integrated with microbial fuel cells influenced by influent and operational conditions

Constructed wetlands integrated with microbial fuel cells (MFC-CWs) have been recently developed and tested for removing antibiotics. However, the effects of carbon source availability, electron transfer flux and cathode conditions on antibiotics removal in MFC-CWs through co-metabolism remained unclear. In this study, four experiments were conducted in MFC-CW microcosms to investigate the influence of carbon source species and concentrations, external resistance and aeration duration on sulfamethoxazole (SMX) and tetracycline (TC) removal and bioelectricity generation performance. MFC-CWs supplied with glucose as carbon source outperformed other carbon sources, and moderate influent glucose concentration (200 mg L^-1) resulted in the best removal of both SMX and TC. Highest removal percentages of SMX (99.4%) and TC (97.8%) were obtained in MFC-CWs with the external resistance of 700 Ω compared to other external resistance treatments. SMX and TC removal percentages in MFC-CWs were improved by 4.98% and 4.34%, respectively, by increasing the aeration duration to 12 h compared to no aeration. For bioelectricity generation performance, glucose outperformed sodium acetate, sucrose and starch, with the highest voltages of 386 ± 20 mV, maximum power density (MPD) of 123.43 mW m^-3, and coulombic efficiency (CE) of 0.273%. Increasing carbon source concentrations from 100 to 400 mg L^-1, significantly (p < 0.05) increased the voltage and MPD, but decreased the internal resistance and CE. The highest MPD was obtained when the external resistance (700 Ω) was close to the internal resistance (600.11 Ω). Aeration not only improved the voltage and MPD, but also reduced the internal resistance. This study demonstrates that carbon source species and concentrations, external resistances and aeration duration, all play vital roles in regulating SMX and TC removal in MFC-CWs.

Effects of substrate type on enhancing pollutant removal performance and reducing greenhouse gas emission in vertical subsurface flow constructed wetland

Constructed wetlands (CWs), known as an alternative clean technology, have been widely used for sewage treatment. However, greenhouse gas (N₂O, CH₄ and CO₂) emissions are the accompanying problem in CWs. To mitigate the net global warming potential (GWP) with the constant removal efficiency for contaminants is attracting wide attention recently. In this study, four CWs were established to explore the effects of substrate types (gravel, walnut shell, manganese ore and activated alumina) on contaminant removal and greenhouse gas emissions. CWs using manganese ore substrate with function of electronic exchange showed high removal efficiencies on COD (90.1%), TN (65.1%), TP (97.1%) and low greenhouse gas flux. The emission fluxes of N₂O, CH₄ and CO₂ were 0.07-0.20, 2.00-252.30 and 337.54-782.57 mg m^-2 h^-1, respectively. Especially, the lowest average CH₄ emission flux in the manganese ore CW was only 2.00 mg m^-2 h^-1 while those of N₂O in walnut shell CW was only 0.07 mg m^-2 h^-1, which will make a significant contribution on the mitigation of GWP of CWs. High-throughput sequencing results indicated that microbial community diversity and richness changed significantly among different substrates. The high pmoA and low mcrA, caused by the introduction of manganese ore as substrate, also explained why there was little CH₄ emission in CWs. Our study provided new insights into GWP mitigation and contaminant removal enhancement in CWs using optimal substrate.

Greenhouse gas emissions from constructed wetlands are mitigated by biochar substrates and distinctly affected by tidal flow and intermittent aeration modes

Biochar substrates and tidal flow (TF) and intermittent aeration (IA) operation modes have recently been applied to improve the treatment performance of constructed wetlands (CWs), but their roles in regulating greenhouse gas (GHG) emissions from CWs are still unclear. In this preliminary study, CO₂, CH₄ and N₂O fluxes and associated microbial characteristics in four groups of subsurface-flow CWs, i.e., ceramsite CWs (C-CWs), biochar-amended CWs (B-CWs), intermittently aerated B-CWs (AB-CWs) and tide-flow B-CWs (TB-CWs), were comparatively investigated. The results showed that biochar amendment significantly mitigated CH₄ and N₂O fluxes from the CWs by supporting higher abundances of mcrA and nosZ genes and higher ratios of pmoA/mcrA and nosZ/(nirK + nirS), thus reducing global warming potential (GWP, a decrease of 55.8%), in addition to promoting total nitrogen (TN) removal by 41.3%, mainly by increasing the abundances and activities of nitrifiers and denitrifiers. The TF mode efficiently improved nitrogen removal, but it greatly increased GHG fluxes since large amounts of GHGs escaped from the empty CW matrix after water draining. IA abated GHG emissions from the CWs, mainly after aeration. TF and IA decreased the abundances of functional bacteria and archaea related to C and N transformation, except nitrifiers, and shaped the microbial community structures. The application of a biochar substrate and IA mode can facilitate the design and operation of CWs in a more ecologically sustainable way.

Novel microbial nitrogen transformation processes in constructed wetlands treating municipal sewage: a mini-review

Traditionally nitrogen transformation in constructed wetlands (CWs) has been attributed to the activities of aerobic autotrophic nitrifiers followed by anoxic heterotrophic denitrifiers. However, the nitrogen balances in such systems are far from being explained as a large fraction of the losses remain unaccounted for. The classical nitrification-denitrification theory has been successfully employed in certain unit processes by culturing fast-growing bacteria, but the CWs offer an ideal environment for slow-growing bacteria that may be beneficially exploited to achieve enhanced nitrogen removal by manipulating the environmental conditions in their favor. In the last three decades, many novel microorganisms have been isolated from CWs that have led to the discovery of some other routes that have made researchers believe could play a significant role in nitrogen transformation processes. The increased understanding of novel discerned pathways like anaerobic ammonium oxidation (ANAMMOX), heterotrophic nitrification and aerobic denitrification, which are mediated by specialized bacteria has indicated that these microorganisms could be enriched by applying selection pressures within CWs for achieving high rates of nitrogen removal. Understanding these novel nitrogen transformation processes along with the associated microbial population can provide new dimensions to the design of CWs for enhanced nitrogen removal.

Role of porous polymer carriers and iron-carbon bioreactor combined micro-electrolysis and biological denitrification in efficient removal of nitrate from wastewater under low carbon to nitrogen ratio

In the current research, a novel bioreactor composed of porous polymer carriers and iron-carbon (PPC@FeC) was established through bacterial immobilized technology. The influence of key factors was studied on the nitrate removal performance of the PPC@FeC bioreactor. The experimental results showed that the highest removal rate of nitrate (7.33 mg L^-1 h^-1) can be obtained with short hydraulic retention times (HRT = 2.0 h) and low carbon-to-nitrogen ratio (C/N = 2.0). The results of high-throughput sequencing revealed that Zoogloea sp. L2 was the dominant strain in bioreactor responsible for nitrate removal. Moreover, the SEM and XRD analyses elucidated that Fe₂O₃ was the final product produced by the interaction of FeC and strain L2. These findings showed that the PPC@FeC bioreactor successfully combined micro-electrolysis and biological denitrification, which exhibited great potential in removing nitrate effectively from wastewater under low C/N ratio and short HRT conditions.

A new insight on the effects of iron oxides and dissimilated metal-reducing bacteria on CH4 emissions in constructed wetland matrix systems

Iron oxides and dissimilated metal-reducing bacteria (DMRB) have been reported to result in a reduction in methane (CH₄) emissions in constructed wetlands (CWs), but their mechanisms on CH₄ production and oxidation remains unclear. Here, a set of CW matrix systems (Control, Fe-CWs, and FeB-CWs) was established to analyze the CH₄ emission reduction from various angles, including the valencies of iron, microbial community structure and enzyme activity. The results revealed that the addition of iron oxides promoted the electron transfer between methanogens and Geobacter to promote CH₄ production, but it was interesting that iron oxides also reduced the enzymes involved in the carbon dioxide (CO₂) reduction pathway and promoted the enzymes that participated in anaerobic oxidation of methane (AOM) thereby leading to the overall reduction in CH₄ emissions. Moreover, DMRB could promote iron reduction thereby further reducing CH₄ emissions by promoting AOM and competing with methanogens for organic substrates.

Recycled utilization of Iris pseudacorus in constructed wetlands: Litters self-consumption and nitrogen removal improvement

Aquatic plants litters from constructed wetlands might become pollutants without proper treatment. Due to its high carbon and low nitrogen contained, Iris pseudacorus litters have potential to be used as carbon source to enhance denitrification process in advanced treatments of secondary effluent from wastewater treatment plants. This study investigated the characteristics of carbon release form Iris pseudacorus litters and its performance on enhancement of nitrogen removal. The batch experiment showed that the organic carbon release process can be simulated by combining dissolution and hydrolysis process, and it was found that dissolved organic matters mainly consisted of 60% sugar and 35% humic acid-like compounds from the neutral detergent solution and hemicellulose of litters. The long-term operation of lab-scale constructed wetlands revealed a high nitrogen removal of 78.81-90.39% in treating the synthetic wastewater treatment plants effluent with the equivalent dosage of 25-150 g litters m^-2 d^-1. Furthermore, it is possible to establish an Iris pseudacorus self-consumed constructed wetland to reuse all of the litters produced during the operation. These findings can contribute to the understanding of the dynamics of carbon release from Iris pseudacorus litters and recycled utilization of plant biomass in the constructed wetlands.

Wetlands for environmental protection

This article presents an update on the research and practical demonstration of wetland-based treatment technologies for protecting water resources and environment covering papers published in 2019. Wetland applications in wastewater treatment, stormwater management, and removal of nutrients, metals, and emerging pollutants including pathogens are highlighted. A summary of studies focusing on the effects of vegetation, wetland design and operation strategies, and process configurations and modeling, for efficient treatment of various municipal and industrial wastewaters, is included. In addition, hybrid and innovative processes with wetlands as a platform treatment technology are presented.

Enhanced nitrogen removal in filled-and-drained vertical flow constructed wetlands: microbial responses to aeration mode and carbon source

For the purpose of enhancing the removal rate of nitrogen (N) and organic matters, intermittent aeration and carbon source were used in filled-and-drained vertical flow constructed wetlands (VFCWs). The results showed that the best removal of COD (74.16%), NH₄⁺-N (93.56%), TN (86.88%), and NO₃^--N (79.65%) was achieved in VFCW1 (aerated with carbon source system). Illumina MiSeq300 high-throughput sequencing showed that carbon source aerated system increases the diversity and richness of the microbial community. The copy numbers of nitrification functional genes (nxrA, amoA), denitrification functional genes (nirS, nirK, nosZ), and anammox functional gene (anammox 16S rRNA) displayed various changes when applied different aeration modes and additional carbon source to each system. An increase of the DO concentration and carbon source facilitated the absolute abundance of microbial nitrification and denitrification functional genes, respectively. All in all, these results demonstrate that carbon source combined with intermittent aeration is valid to improve the pollutant treatment performance in these systems.

Advanced treatment of effluent from municipal wastewater treatment plant by strengthened ecological floating bed

The performance of eological floating bed (EFB) with novel carbon source (CS) and reed biochar substrate (RBS) derived from reed straw (RS) was evaluated for the advanced treatment of effluent from wastewater treatment plants (WWTPs). The average carbon releasing capacity of CS was 4.50 mg/g, and the P adsorption capacity of RBS was 0.39 mg/g. The additional CS and RBS increased the average removal efficiencies of total nitrogen (TN) and total phosphorus (TP) by 57.6% and 46.7%, respectively. Furthermore, the high-throughput sequencing results revealed significantly different microbial species richness and diversity due to the CS and RBS. Some genera related to nitrogen removal, such as Pseudomonas, Rhodobacter, Hydrogenophaga, Bradyrhizobium, Acinetobacter and Thiobacillus, were enriched in the EFB with CS and RBS. This study provided a suitable method for effectively treating low C/N wastewater such as WWTPs effluent using EFB strengthened by processed wetland plant.

Impact of biochar on greenhouse gas emissions from constructed wetlands under various influent chemical oxygen demand to nitrogen ratios

Biochar is widely used for nutrient removal in constructed wetlands (CWs); however, its influence on greenhouse gas (GHG) emissions from CWs remains unclear. Here, biochar was used to mitigate the global warming potential (GWP) from CWs and promote the removal of contaminants from simulated domestic wastewater under different influent chemical oxygen demand to nitrogen ratios (COD/N = 3, 6, 9, 12). Results demonstrated that biochar could improve the removal of COD, NH₄⁺- N, and TN. The average N₂O and CO₂ fluxes were significantly lower and CH₄ fluxes were higher in biochar-added CWs than those in none-biochar CWs. Biochar reduced GWP values of N₂O and CH₄ from 18.5% to 24.0%. N₂O fluxes and GWP decreased, while CH₄ and CO₂ fluxes increased as COD/N ratios increased. Additionally, biochar increased the abundance of Geobacter and denitrifiers such as Hydrogenophaga. Overall, biochar could not only promote the removal of nutrients but also mitigate GWP in CWs.

Roles of biochar media and oxygen supply strategies in treatment performance, greenhouse gas emissions, and bacterial community features of subsurface-flow constructed wetlands

Biochar-based subsurface-flow constructed wetlands (CWs) with intermittent aeration (IA) or tidal flow (TF) oxygen supply strategies were established to treat domestic wastewater. The results showed that biochar achieved higher nutrient removal and lower greenhouse gas (GHG) emissions than ceramsite while supporting more diverse bacterial communities and higher abundances of functional taxa. Both IA and TF effectively enhanced nutrient removal, though the latter was more efficient and practical, and aeration conditions greatly influenced nutrient removal efficiency. GHG emissions were decreased by IA but were slightly increased by TF. Both oxygen supply methods significantly shaped the biofilm microbial communities and influenced biodiversity and richness, with observably higher proportions of potential nitrifiers and denitrifiers present in aerated CWs. Overall, biochar-based CWs operated with oxygen supply strategies provide superior treatment of decentralized wastewater.

Enhanced optimal removal of nitrogen and organics from intermittently aerated vertical flow constructed wetlands: Relative COD/N ratios and microbial responses

Carbon source and dissolved oxygen are the critical factors which sustain the stable redox environment for the microbes to implement the removal of nitrogen and organics in vertical flow constructed wetlands (VFCWs). The effect mechanisms of the COD/N ratios in intermittently aerated VFCWs are needed to be investigated in order to increase the synchronous removal efficiency of pollutants. In this study, the combined effects of COD/N ratios (3, 6, 12) and intermittent aeration in VFCWs on pollutant removal, microbial communities and related function genes were studied. The results showed the increase of COD/N ratios from 3 to 12 enhanced the removal efficiency of TN, NO₃^--N and COD. The removals of NH₄⁺-N decreased as the COD/N ratio increased. The optimal removals of TN (87.65%), NH₄⁺-N (93.20%), NO₃^--N (80.80%) and COD (73.93%) were obtained in VFCW2 (COD/N ratios was 6). Illumina Miseq High-throughput sequencing analysis showed that high COD/N ratios increased the richness and diversity of microbial communities. The absolute abundance of nirK, nosZ, nirS, amoA, nxrA, and anammox bacterial 16S rRNA presented various changes under the different ratios of COD/N. The increase of COD/N ratios enhanced the copy numbers of nirS, nirK and nosZ, which participate in denitrification process. High COD/N ratios (6 and 12) were in favor of Actinobacteria, Firmicutes and Chloroflexi, which mainly play important roles in the process of denitrification. This paper implies that the combination of carbon source and aeration is necessary to sustain high microbial activities during pollutant removal in VFCWs.

Thiosulfate-driven autotrophic and mixotrophic denitrification processes for secondary effluent treatment: Reducing sulfate production and nitrous oxide emission

Three ecological floating beds (EFBs) with different additional electron donors including sodium thiosulfate, mixed electron donors of sodium thiosulfate and sodium acetate and without additional electron donors were established to compare the differences of nitrogen removal efficiency, nitrous oxide emission, microbial community and functional gene between autotrophic and mixotrophic denitrification. Results showed denitrification efficiency was nearly 100% in both autotrophic and mixotrophic process when electron donors were sufficient while that ranged from 4 to 43% without additional electron donors. Sodium acetate addition could effectively decrease sulfate concentration in effluent and nitrogen oxide flux. In addition, high-throughput sequencing analysis revealed autotrophic denitrifying bacteria were dominant in autotrophic denitrification while autotrophic, facultative and heterotrophic denitrifying bacteria coexisted in mixotrophic denitrification, and there was no dominant genus. For EFB with mixed external autotrophic and heterotrophic electron donors, it can not only achieve better denitrification efficiency, but also reduce the emission of nitrous oxide.

Multifunctional modified polyvinyl alcohol: A powerful biomaterial for enhancing bioreactor performance in nitrate, Mn(II) and Cd(II) removal

The co-existence of multiple pollutants in wastewater such as nitrate and heavy metal, is of high concern due to the potential environmental impact. In this study, a novel biomaterial PPy@Fe₃O₄/PVA was synthesized as a multifunctional bacteria immobilized carrier, to enhance simultaneous denitrification, Cd(II) and Mn(II) removal efficiency in bioreactor environments. The morphology and main components of the PPy@Fe₃O₄/PVA material were characterized by SEM and XRD. Using PPy@Fe₃O₄/PVA as a carrier, the maximum removal efficiencies for nitrate (0.207 mg L^-1·h^-1), Mn(II) (90.98%) and Cd(II) (98.78%) were increased by 27.05%, 30.27%, and 16.48%, respectively, compared to in the absence of PPy@Fe₃O₄/PVA. Regeneration experiments were performed, demonstrating the excellent stability and reusability of the PPy@Fe₃O₄/PVA material. Furthermore, effects of key factors were investigated on the performance of the PPy@Fe₃O₄/PVA bioreactor in simultaneous denitrification, Mn(II) and Cd(II) removal. Experimental results indicate that the highest nitrate, Mn(II) and Cd(II) removal efficiencies were obtained under the conditions of HRT of 10 h, initial Mn(II) concentration of 40 mg/L and initial Cd(II) concentration of 10 mg/L. Gas chromatography analysis indicated that N₂ was the mainly final gaseous product. Moreover, the bioreactor community diversity was markedly influenced by the initial concentration of Cd(II) and Pseudomonas sp. H117 played a primary role in the process of simultaneous denitrification, Mn(II) and Cd(II) removal.