The critical role of lignin in lignocellulosic biomass conversion and recent pretreatment strategies: A comprehensive review

Lignin fractionation and condensation in aromatic-additive-assisted acidic pretreatment and their influence on lignin's effect on the enzymatic hydrolysis

Factors influencing inhibition of lignin on the enzymatic hydrolysis have not been fully elucidated. This study aims to elucidate the effects of lignin fractionation and condensation on its inhibition on enzymatic hydrolysis in aromatic-additive-assisted acidic pretreatment using 2-naphthol (2 N), 2-naphthol-7-sulfonate (NS), and resorcinol (RS). Through simulation reactions of pretreatment and physiochemical analyses of ethanol-extractable lignins (ELs) and cellulolytic enzyme lignins (CELs) from pretreatment, it was observed that 2 N addition in the acidic pretreatment could suppress lignin condensation. This suppression consequently mitigated inhibition of EL-AP-2 N on the enzymatic hydrolysis of Avicel. Simultaneously, addition of NS in the pretreatment can enhance lignin fractionation by facilitating decomposition of lignin into water and ethanol soluble fractions, thereby mitigating inhibition of CEL-AP-NS on the enzymatic hydrolysis. Meanwhile, with RS in the pretreatment, EL-AP-RS and CEL-AP-RS demonstrated the most pronounced inhibition among ELs and CELs. This inhibition may be attributed to the increased phenolic OH groups with the introduction of RS units. A heatmap analysis revealing relationship between lignin characteristics and its inhibition indicated that ELs exhibit reduced inhibition on enzymatic hydrolysis when lignin condensation was suppressed. Conversely, CELs would show diminished inhibitory effects when lignin particle sizes were smaller and lignin fractionation was stronger.

Achieving synergistic enhancement in the anaerobic digestion of corn straw by (CH4 + CO2) nanobubbles in conjunction with optimized particle sizes

Nanobubbles (NBs) technology has been proven to promote methane production from anaerobic digestion (AD). In this study, the synergistic effects of (CH4 + CO2)-nanobubble water ((CH4 + CO2)-NBW) combined with varying particle sizes of corn straw on the AD were investigated. As findings, adding (CH4 + CO2)-NBW effectively promoted the methane production from AD of corn straw with different particle sizes. The maximum cumulative methane yield (186.42 mL/ g-volatile solids) was achieved in Group a with the addition of (CH4 + CO2)-NBW, representing a 16.89 % increase compared to the control. Furthermore, (CH4 + CO2)-NBW could enhance the enzymatic activity. The activities of β-glucosidase and coenzyme F420 were increased by 6.70 % and 11.48 %, respectively. The results of microbial community structure revealed that the addition of (CH4 + CO2)-NBW could improve the abundance of dominant bacteria (norank_JS1, norank_Aminicenantales, and Bacteroidetes_vadinHA17) and archaea (Methanomassiliicoccaceae, Methanobacteriaceae, and norank_Bathyarchaeia). This study provides new insights into the application of nanobubbles in the AD of biomass.

Simultaneous enhancement of activity and stability of Bacillus safensis-derived laccase and its application in lignocellulose saccharification

Effective hydrolysis of lignocelluloses for producing reducing sugar is impeded by the covalent binding of hemicellulose and cellulose through lignin, which could be eliminated by laccases. This study identified a novel thermostable laccase from Bacillus safensis TCCC 111022 and created an iterative mutant E231D/Y441H, exhibiting 1.59-fold greater specific activity and a 183 % greater half-life at 80°C than the wild-type enzyme. Computational analysis revealed that the stability and activity of the E231D/Y441H could be simultaneously enhanced by increasing the flexibility of the ring around the substrate binding pocket. Additionally, the saccharification efficiency of sugarcane bagasse and corn stalks were both enhanced by 235 % in the system adding E231D/Y441H, mixed-cellulases, and mediator (1-hydroxybenzotriazole) compared to the samples treated with mixed-cellulases. The findings of this research provide a reference for the degradation of lignocellulosic substrates and contribute to the sustainable development of biomass-based industries.

Is Kraft Pulping the Future of Biorefineries? A Perspective on the Sustainability of Lignocellulosic Product Development

By reflecting on the history and environmental impact of conventional biorefining, such as kraft pulping, we aim to explore important questions about how natural polymers can be more sustainably sourced to develop bio-products and reduce reliance on plastics. Since the Industrial Revolution, chemical pulping processes have enabled the mass production of cellulosic products from woody biomass. Kraft pulping, which dominates within modern pulp and paper mills, has significantly contributed to environmental pollution and carbon emissions due to sulfurous byproducts and its high water and energy consumption. While chemical pulping technologies have advanced over time, with improvements aimed at enhancing sustainability and economic feasibility, conventional biorefineries still face challenges related to biomass conversion efficiency and environmental impact. For example, efforts to fully utilize wood resources, such as isolating lignin from black liquor, have made limited progress. This perspective provides a thoughtful examination of the growth of chemical pulping, particularly the kraft process, in the production of consumer goods and its environmental consequences. It also presents key insights into the bottlenecks in developing truly sustainable biomass conversion technologies and explores potential alternatives to traditional chemical pulping.

Study of the Influence of Bamboo Suspension Water-Removal Processes on the Properties of Bamboo-Based Molding Materials

Bamboo is a fast-growing lignocellulosic plant in nature. It is an abundant and renewable resource with wide applications. The processing of bamboo results in a large amount of residue. In this paper, we developed a method to utilize bamboo residue to prepare a novel lightweight porous molding material. A hydrated thermochemical grinding process was proposed to disintegrate bamboo fibers and activate bamboo's own binding components. The influence of the water removal by pressure from bamboo suspension and subsequent different drying methods on the product's properties was evaluated. The two-step drying ensured a low production cost and high product quality. The bamboo molding material was characterized based on thermal stability, morphology, functional groups, particle size distribution, crystallinity, and mechanical strength. A lightweight porous material was obtained with a density of 0.23-0.35 g/cm3 by freeze-drying. A high mechanical strength was obtained with a tensile strength of 0.62 MPa and a compressive strength of 10.31 MPa by oven drying. The auto-adhesive mechanisms, including fiber anchorage, polymerization, water plasticization, and heat plasticization, were discussed. The bamboo molding material is a reconstruction of bamboo cell wall components and is easy to recycle. It has potential applications in construction and buildings, packaging, and indoor furnishings.

Biorefinery and Bioremediation Strategies for Efficient Management of Recalcitrant Pollutants Using Termites as an Obscure yet Promising Source of Bacterial Gut Symbionts: A Review

Lignocellulosic biomass (LCB) in the form of agricultural, forestry, and agro-industrial wastes is globally generated in large volumes every year. The chemical components of LCB render them a substrate valuable for biofuel production. It is hard to dissolve LCB resources for biofuel production because the lignin, cellulose, and hemicellulose parts stick together rigidly. This makes the structure complex, hierarchical, and resistant. Owing to these restrictions, the junk production of LCB waste has recently become a significant worldwide environmental problem resulting from inefficient disposal techniques and increased persistence. In addition, burning LCB waste, such as paddy straws, is a widespread practice that causes considerable air pollution and endangers the environment and human existence. Besides environmental pollution from LCB waste, increasing industrialization has resulted in the production of billions of tons of dyeing wastewater from several industries, including textiles, pharmaceuticals, tanneries, and food processing units. The massive use of synthetic dyes in various industries can be detrimental to the environment due to the recalcitrant aromatic structure of synthetic dyes, similar to the polymeric phenol lignin in LCB structure, and their persistent color. Synthetic dyes have been described as possessing carcinogenic and toxic properties that could be harmful to public health. Environmental pollution emanating from LCB wastes and dyeing wastewater is of great concern and should be carefully handled to mitigate its catastrophic effects. An effective strategy to curtail these problems is to learn from analogous systems in nature, such as termites, where woody lignocellulose is digested by wood-feeding termites and humus-recalcitrant aromatic compounds are decomposed by soil-feeding termites. The termite gut system acts as a unique bioresource consisting of distinct bacterial species valued for the processing of lignocellulosic materials and the degradation of synthetic dyes, which can be integrated into modern biorefineries for processing LCB waste and bioremediation applications for the treatment of dyeing wastewaters to help resolve environmental issues arising from LCB waste and dyeing wastewaters. This review paper provides a new strategy for efficient management of recalcitrant pollutants by exploring the potential application of termite gut bacteria in biorefinery and bioremediation processing.

Sequential pretreatment with hydroxyl radical and manganese peroxidase for the efficient enzymatic saccharification of corn stover

BACKGROUND

White rot fungi produce various reactive oxygen species and ligninolytic enzymes for lignocellulose deconstruction. However, their interactions during the deconstruction of lignocellulosic structural barriers for efficient enzymatic saccharification remain unclear.

RESULTS

Herein, the extracellular enzyme activities and secretomic analysis revealed the sequential expression of hydroxyl radical (⋅OH) and manganese peroxidases (MnPs) for lignocellulose deconstruction by the white rot fungus Irpex lacteus. Subsequently, in vitro functional studies found that ⋅OH possessed the ability to disrupt the smooth surface structure of corn stover, resulting in increased enzymatic saccharification and cellulose accessibility. Purified recombinant MnPs from I. lacteus were able to cleave the β-O-4 bond in phenolic and non-phenolic lignin model dimers without the help of any mediators. Furthermore, the sequential pretreatment of corn stover with ⋅OH and MnP exhibited significant synergistic effects, increasing enzymatic saccharification and cellulose accessibility by 2.9-fold and 1.8-fold, respectively.

CONCLUSIONS

These results proved for the first time the synergistic effects of ⋅OH and MnP pretreatment in improving the enzymatic saccharification and cellulose accessibility of corn stover. These findings also demonstrated the potential application of ⋅OH and MnP pretreatment for the efficient enzymatic saccharification of corn stover.

Bacterial valorization of lignin for the sustainable production of value-added bioproducts

As the most abundant aromatic biopolymer in the biosphere, lignin represents a promising alternative feedstock for the industrial production of various value-added bioproducts with enhanced economical value. However, the large-scale implementation of lignin valorization remains challenging because of the heterogeneity and irregular structure of lignin. General fragmentation and depolymerization processes often yield various products, but these approaches necessitate tedious purification steps to isolate target products. Moreover, microbial biocatalytic processes, especially bacterial-based systems with high metabolic activity, can depolymerize and further utilize lignin in an eco-friendly way. Considering that wild bacterial strains have evolved several metabolic pathways and enzymatic systems for lignin degradation, substantial efforts have been made to exploit their potential for lignin valorization. This review summarizes recent advances in lignin valorization for the production of value-added bioproducts based on bacterial systems. Additionally, the remaining challenges and available strategies for lignin biodegradation processes and future trends of bacterial lignin valorization are discussed.

Structure changes of lignin and their effects on enzymatic hydrolysis for bioethanol production: a focus on lignin modification

Enzymatic hydrolysis contributes to obtaining fermentable sugars using pretreated lignocellulose materials for bioethanol generation. Unfortunately, the pretreatment of lignocellulose causes low substrate enzymatic hydrolysis, which is due to the structure changes of lignin to produce main phenolic by-products and non-productive cellulase adsorption. It is reported that modified lignin enhances the speed of enzymatic hydrolysis through single means to decrease the negative effects of fermentation inhibitors or non-productive cellulase adsorption. However, a suitable modified lignin should be selected to simultaneously reduce the fermentation inhibitors concentration and non-productive cellulase adsorption for saving resources and maximizing the enzymatic hydrolysis productivity. Meanwhile, the adsorption micro-mechanisms of modified lignin with fermentation inhibitors and cellulase remain elusive. In this review, different pretreatment effects toward lignin structure, and their impacts on subsequent enzymatic hydrolysis are analyzed. The main modification methods for lignin are presented. Density functional theory is used to screen suitable modification methods for the simultaneous reduction of fermentation inhibitors and non-productive cellulase adsorption. Lignin-fermentation inhibitors and lignin-cellulase interaction mechanisms are discussed using different advanced analysis techniques. This article addresses the gap in previous reviews concerning the application of modified lignin in the enhancement of bioethanol production. For the first time, based on existing studies, this work posits the hypothesis of applying theoretical simulations to screen efficient modified lignin-based adsorbents, in order to achieve a dual optimization of the detoxification and saccharification processes. We aim to improve the integrated lignocellulose transformation procedure for the effective generation of cleaner bioethanol.

Applications, challenges and prospects of superabsorbent polymers based on cellulose derived from lignocellulosic biomass

The synthetic superabsorbent polymers (SAPs) market is experiencing significant growth, with applications spanning agriculture, healthcare, and civil engineering, projected to increase from $9.0 billion USD in 2019 to $12.9 billion USD by 2024. Despite this positive trend, challenges such as fluctuating raw material costs and lower biodegradability of fossil fuel-based SAPs could impede further expansion. In contrast, cellulose and its derivatives present a sustainable alternative due to their renewable, biodegradable, and abundant characteristics. Lignocellulosic biomass (LCB), rich in cellulose and lignin, shows promise as a source for eco-friendly superabsorbent polymer (SAP) production. This review discusses the applications, challenges, and future prospects of SAPs derived from lignocellulosic resources, focusing on the cellulose extraction process through fractionation and various modification and crosslinking techniques. The review underscores the potential of cellulose-based SAPs to meet environmental and market needs, offering a viable path forward in the quest for more sustainable materials.

Biotechnological valorization of levulinic acid as a non-sugar feedstock: New paradigm in biorefineries

Due to the severe climate crisis, biorefineries have been highlighted as replacements for fossil fuel-derived refineries. In traditional sugar-based biorefineries, levulinic acid (LA) is a byproduct. Nonetheless, in 2002, the US Department of Energy noted that LA is a significant building block obtained from biomass, and the biorefinery paradigm has shifted from being sugar-based to non-sugar-based. Accordingly, LA is of interest in this review since it can be converted into useful precursors and ultimately can broaden the product spectrum toward more valuable products (e.g., fuels, plastics, and pharmaceuticals), thereby enabling the construction of economically viable biorefineries. This study comprehensively reviews LA production techniques utilizing various bioresources. Recent progress in enzymatic and microbial routes for LA valorization and the LA-derived product spectrum and its versatility are discussed. Finally, challenges and future outlooks for LA-based non-sugar biorefineries are suggested.

Recovery of green phenolic compounds from lignin-based source: Role of ferulic acid esterase towards waste valorization and bioeconomic perspectives

The production of chemicals/products so far relies on fossil-based resources with the creation of several environmental problems at the global level. In this situation, a sustainable and circular economy model is necessitated to mitigate global environmental issues. Production of biowaste from various processing industries also creates environmental issues which would be valorized for the production of industrially important reactive and bioactive compounds. Lignin acts as a vital part in biowaste composition which can be converted into a wide range of phenolic compounds. The phenolic compounds have attracted much attention, owing to their influence on diverse not only organoleptic parameters, such as taste or color, but also active agents for active packaging systems. Crop residues of varied groups, which are an affluent source of lignocellulosic biomass could serve as a renewable resource for the biosynthesis of ferulic acid (FA). FA is obtained by the FA esterase enzyme action, and it can be further converted into various tail end phenolic flavor green compounds like vanillin, vanillic acid and hydroxycinnamic acid. Lignin being renewable in nature, processing and management of biowastes towards sustainability is the need as far as the global industrial point is concerned. This review explores all the approaches for conversion of lignin into value-added phenolic compounds that could be included to packaging applications. These valorized products can exhibit the antioxidant, antimicrobial, cardioprotective, anti-inflammatory and anticancer properties, and due to these features can emerge to incorporate them into production of functional foods and be utilization of them at active food packaging application. These approaches would be an important step for utilization of the recovered bioactive compounds at the nutraceutical and food industrial sectors.

RcTRP5 Transcription Factor Mediates the Molecular Mechanism of Lignin Biosynthesis Regulation in R. chrysanthum against UV-B Stress

UV-B stress destroys the photosynthetic system of Rhododendron chrysanthum Pall. (R. chrysanthum), as manifested by the decrease of photosynthetic efficiency and membrane fluidity, and also promotes the accumulation of lignin. The MYB (v-myb avian myeloblastosis viral oncogene homolog) family of transcription factors can be involved in the response to UV-B stress through the regulation of lignin biosynthesis. This study indicated that both the donor and recipient sides of the R. chrysanthum were significantly damaged based on physiological index measurements made using OJIP curves under UV-B stress. The analysis of bioinformatics data revealed that the RcTRP5 transcription factor exhibits upregulation of acetylation at the K68 site, directly regulating the biosynthesis of lignin. Additionally, there was upregulation of the K43 site and downregulation of the K83 site of the CAD enzyme, as well as upregulation of the K391 site of the PAL enzyme. Based on these findings, we conjectured that the RcTRP5 transcription factor facilitates acetylation modification of both enzymes, thereby indirectly influencing the biosynthesis of lignin. This study demonstrated that lignin accumulation can alleviate the damage caused by UV-B stress to R. chrysanthum, which provides relevant ideas for improving lignin content in plants, and also provides a reference for the study of the metabolic regulation mechanism of other secondary substances.

Matrix-free laser desorption/ionization mass spectrometry imaging for rapid evaluation of wood biomass conversion

RATIONALE

This study overcomes traditional biomass analysis limitations by introducing a pioneering matrix-free laser desorption/ionization (LDI) approach in mass spectrometry imaging (MSI) for efficient lignin evaluation in wood. The innovative acetic acid-peracetic acid (APA) treatment significantly enhances lignin detection, enabling high-throughput, on-site analysis.

METHODS

Wood slices, softwood from a conifer tree (Japanese cypress) and hardwood from a broadleaf tree (Japanese beech), were analyzed using MSI with a Fourier transform ion cyclotron resonance mass spectrometer. The developed APA treatment demonstrated effectiveness for MSI analysis of biomass.

RESULTS

Our imaging technique successfully distinguishes between earlywood and latewood and enables the distinct visualization of lignin in these and other wood tissues, such as the radial parenchyma. This approach reveals significant contrasts in MSI. It has identified intense ions from β-O-4-type lignin, specifically in the radial parenchyma of hardwood, highlighting the method's precision and utility in wood tissue analysis.

CONCLUSIONS

The benefits of matrix-free LDI include reduced peak overlap, consistent sample quality, preservation of natural sample properties, enhanced analytical accuracy, and reduced operational costs. This innovative approach is poised to become a standard method for rapid and precise biomass evaluation and has important applications in environmental research and sustainable resource management and is crucial for the effective management of diverse biomass, paving the way towards a sustainable, circular society.

A simple approach to produce hydrophobic biobased coatings using methylcellulose and organosolv lignin

Substituting plastics with circular and sustainable alternatives has increasingly become a priority. Protective coatings, crucial components in numerous industries, are now in demand for biodegradable options to replace their plastic-based counterparts. Being one of nature's most abundant components, lignin remains underutilized, and this study focuses on investigating its potential for the production of biobased coatings. The method used here involved formulating coating suspensions by mixing methylcellulose and organosolv lignin powders and adding water to the mixture. Glass wafers were coated with the formulated suspensions using spin-coating. The morphology of the coated surfaces was assessed using optical and scanning electron microscopy. In addition, the wettability of the surfaces was examined through water contact angle experiments, and a numerical model was introduced to predict the water contact angle evolution over time. The results revealed that the sample coated with a 2.5 wt% lignin suspension exhibited the highest initial contact angle (114°), with a decreasing trend as the lignin fraction increases. Moreover, coatings with 3.5 wt% lignin and above exhibited lower surface coverage due to lignin particle aggregation and surface defects. By approximating the water droplet on the surface as a spherical cap, the introduced numerical model successfully predicted the time-dependent evolution of the water contact angle by showing strong alignment with experimental results. Taken altogether, we have showcased here a method for modifying coating properties-in a practical sense from water-absorbent to splash-proof-using readily available forest-based materials. This advancement is paving the way for sustainable protective packaging, aiming to replace styrofoam in the electronics and food industries.

Valorization of residual lignocellulosic biomass in South America: a review

Residual lignocellulosic biomass (RLB) is a valuable resource that can help address environmental issues by serving as an alternative to fossil fuels and as a raw material for producing various value-added molecules. To gain a comprehensive understanding of the use of lignocellulosic waste in South America, a review was conducted over the last 4 years. The review focused on energy generation, biofuel production, obtaining platform molecules (such as ethanol, hydroxymethylfurfural, furfural, and levulinic acid), and other materials of interest. The review found that Brazil, Colombia, and Ecuador had the most RLB sources, with sugarcane, oil palm, and rice crop residues being the most prominent. In South America, RLB is used to produce biogas, syngas, hydrogen, bio-oil, biodiesel, torrefied biomass, pellets, and biomass briquettes. The most studied and produced value-added molecule was ethanol, followed by furfural, hydroxymethylfurfural, and levulinic acid. Other applications of interest that have been developed with RLB include obtaining activated carbon and nanomaterials. Significant progress has been made in South America in utilizing RLB, and some countries have been more proactive in regulating its use. However, there is still much to learn about the potential of RLB in each country. This review provides an updated perspective on the typification and valorization of residual biomass in South America and discusses the level of research and technology being applied in the region. This information can be helpful for future research on RLB in South America.

Synergism of jet milling and deep eutectic solvent pretreatment on grapevine lignin fractionation and enhancing enzymatic hydrolysis

Herein, we investigated the synergistic effects of jet milling (JM) and deep eutectic solvent (DES) pretreatment on the fractionation of grapevine lignin and the consequent enhancement of enzymatic hydrolysis. Grapevine, a substantial byproduct of the wine industry, was subjected to JM pretreatment to produce finely powdered particles (median diameter D50 = 98.90), which were then further treated with acidic ChCl-LA and alkaline K2CO3-EG DESs. The results revealed that the combined JM + ChCl-LA pretreatment significantly increased the cellulose preservation under optimal conditions (110 °C, 4 h, and 20 % water content), achieving removal rates of 74.18 % xylan and 66.05 % lignin, respectively. The pretreatment temperature and inhibitor production were reduced, resulting in a remarkable threefold increase in glucose yield compared to untreated samples. Moreover, the structural analysis of the pretreated lignin indicated an enrichment of phenolic units, leading to enhanced antioxidant and antibacterial activities, particularly in the JM pretreated samples. These findings underscore the promising potential of the synergistic JM and DES pretreatment in facilitating the efficient utilization of grapevine lignocellulosic biomass for sustainable biorefinery technologies.

Particle size of insoluble fibres and gelation of soluble fibres influence digesta passage rate throughout the gastrointestinal tract of finishing pigs

Fibres, as abundant in agricultural by-products, exhibit a large range of physicochemical properties that can influence digestive processes such as digesta mean retention time (MRT), thereby affecting nutrient digestion kinetics. In this study, we investigated the effects of particle size of insoluble fibres, and gelation of soluble fibres on MRT of liquids, fine solids, and fibrous particles in the different segments of the gastrointestinal tract (GIT) of pigs. Twenty-four boars (51.6 ± 4.90 kg) were allocated to four diets; two diets contained 15% wheat straw, either coarsely chopped or finely ground (1-mm screen), two diets contained 27% wheat bran without or with the addition of 10% low-methylated pectin. After 14 days of adaptation to the diet, a total collection of faeces was performed to determine the total tract digestibility of nutrients. Thereafter, pigs were fed diets supplemented with tracers for at least 5 days and dissected following a frequent feeding procedure to approach steady-state passage of digesta. The MRT of liquids (Co-EDTA), fine solids (TiO2), and fibrous particles (Chromium-mordanted fibres) in the different segments of the GIT were quantified. In the stomach, particle size reduction of straw decreased the MRT of fine solids by 02:39 h, and fibrous particles by 07:21 h (P < 0.10). Pectin addition to the wheat bran diet reduced the MRT of fine solids by 03:09 h, and fibrous particles by 07:10 h (P < 0.10), but not of liquids, resulting in less separation between digesta phases in the stomach compared with the bran diet (P < 0.05). In the mid-small intestine (SI), pectin addition reduced the MRT of fibrous particles and the separation between fibrous particles and fine solids. No further effects of particle size reduction of straw nor pectin addition on MRT and digestibility of starch, nitrogen, or fat were observed in the SI. In the large intestine (LI), particle size reduction of straw reduced separation between fibrous particles and fine solids (P < 0.10), while pectin addition had no effects. Total tract, non-starch polysaccharide degradation of straw was poor (∼31%), and unaffected by particle size reduction (P > 0.10). The complete fermentation of pectin did not influence the degradation of wheat bran fibres (∼51%). In conclusion, the effects of particle size of insoluble fibres and gelling properties of soluble fibres on the passage of digesta phases were most pronounced in the stomach, but less prominent in distal segments of the GIT.

Extraction of lignin-containing nanocellulose fibrils from date palm waste using a green solvent

Lignin-containing nanocellulose (LNC) is a compelling alternative to traditional nanocellulose (NC), it offers enhanced yields and a reduction in the demand for toxic chemicals. This research involves the isolation of LNC from date palm waste using a green hydrolysis process and its subsequent characterization. The potential of using ionic liquids (ILs) as green solvents to isolate LNC has not yet been explored. Our findings suggest that 1-ethyl-3-methylimidazolium chloride ([Emim]Cl) can hydrolyze partially delignified and unbleached lignocellulose, achieving LNC synthesis. The obtained LNC showed a higher yield than its NC counterpart and exhibited rod-shaped fibers with nanoscale diameters and micrometer lengths, indicating a high aspect ratio. Dynamic Light Scattering (DLS) results indicate average particle sizes of 143.20 nm for NC and 282.30 nm for LNC, with a narrow particle size distribution conforming their monodisperse behavior. Thermogravimetric analysis and differential scanning calorimetry revealed high thermal stability (initial degradation temperature = 222.50 °C and glass transition temperature = 84.45°C) of LNC. Moreover, the obtained LNC fibers were crystalline (crystallinity index = 52.76 %). Their activation energy (124.95 kJ/mol) was determined using the Coats-Redfern method by employing eight solid-state diffusion models. Overall, this study motivates the use of ILs as green solvents to produce lignocellulose derivatives that are suitable for various applications.

Temporal dynamics of lignin degradation in Quercus acutissima sawdust during Ganoderma lucidum cultivation

Despite a fair amount of lignin conversion during mycelial growth, previous structural analyses have not yet revealed how lignin changes continuously and what the relationship is between lignin and ligninolytic enzymes. To clarify these aspects, Quercus acutissima sawdust attaching Ganoderma lucidum mycelium collected from different growth stage was subjected to analysis of lignin structure and ligninolytic enzyme activity. Two key periods of lignin degradation are found during the cultivation of G. lucidum: hypha rapid growth period and primordium formation period. In the first stage, laccase activity is associated with the opening of structures such as methoxyls, β-O-4' substructures and guaiacyl units in lignin, as well as the shortening of lignin chains. Manganese peroxidases and lignin peroxidases are more suitable for degrading short chain lignin. The structure of phenylcoumarans and syringyl changes greatly in the second stage. The results from sawdust attaching mycelium provide new insights to help improve the cultivation substrate formulation of G. lucidum and understand biomass valorization better.

Innovative approaches for amino acid production via consolidated bioprocessing of agricultural biomass

Agricultural plantations in Indonesia and Malaysia yield substantial waste, necessitating proper disposal to address environmental concerns. Yet, these wastes, rich in starch and lignocellulosic content, offer an opportunity for value-added product development, particularly amino acid production. Traditional methods often rely on costly commercial enzymes to convert biomass into fermentable sugars for amino acid production. An alternative, consolidated bioprocessing, enables the direct conversion of agricultural biomass into amino acids using selected microorganisms. This review provides a comprehensive assessment of the potential of agricultural biomass in Indonesia and Malaysia for amino acid production through consolidated bioprocessing. It explores suitable microorganisms and presents a case study on using Bacillus subtilis ATCC 6051 to produce 9.56 mg/mL of amino acids directly from pineapple plant stems. These findings contribute to the advancement of sustainable amino acid production methods using agricultural biomass especially in Indonesia and Malaysia through consolidated bioprocessing, reducing waste and enhancing environmental sustainability.

Valorization of Agricultural Rice Straw as a Sustainable Feedstock for Rigid Polyurethane/Polyisocyanurate Foam Production

Agricultural rice straw (RS), often discarded as waste in farmlands, represents a vast and underutilized resource. This study explores the valorization of RS as a potential feedstock for rigid polyurethane/polyisocyanurate foam (RPUF) production. The process begins with the liquefaction of RS to create an RS-based polyol, which is then used in a modified foam formulation to prepare RPUFs. The resulting RPUF samples were comprehensively characterized according to their physical, mechanical, and thermal properties. The results demonstrated that up to 50% by weight of petroleum-based polyol can be substituted with RS-based polyol to produce a highly functional RPUF. The obtained foams exhibited a notably low apparent density of 18-24 kg/m3, exceptional thermal conductivity ranging from 0.031-0.041 W/m-K, and a high compressive strength exceeding 250 kPa. This study underlines the potential of the undervalued agricultural RS as a green alternative to petroleum-based feedstocks to produce a high-value RPUF. Additionally, the findings contribute to the sustainable utilization of abundant agricultural waste while offering an eco-friendly option for various applications, including construction materials and insulation.

Molecular insights into inhibiting effects of lignin on cellulase investigated by molecular dynamics simulation

The hydrolysis of lignocellulose into fermentable monosaccharides using cellulases represents a critical stage in lignocellulosic bioconversion. However, the inactivation of cellulase in the presence of lignin is attributed to the high cost of biofinery. To address this challenge, a comprehensive investigation into the structure-function relationship underlying lignin-driven cellulase inactivation is essential. In this study, molecular docking and molecular dynamics (MD) simulations were employed to explore the impacts of lignin fragments on the catalytic efficiency of cellulase at the atomic level. The findings revealed that soluble lignin fragments and cellulose could spontaneously form stable complexes with cellulase, indicating a competitive binding scenario. The enzyme's structure remained unchanged upon binding to lignin. Furthermore, specific amino acid residues have been identified as involved in interactions with lignin and cellulose. Hydrophobic interactions were found to dominate the binding of lignin to cellulase. Based on the mechanisms underlying the interactions between lignin fragments and cellulase, decreased hydrophobicity and change in the charge of lignin may mitigate the inhibition of cellulase. Furthermore, site mutations and chemical modification are also feasible to improve the efficiency of cellulase. This study may contribute valuable insights into the design of more lignin-resistant enzymes and the optimization of lignocellulosic pretreatment technologies.Communicated by Ramaswamy H. Sarma.

A critical assessment on scalable technologies using high solids loadings in lignocellulose biorefinery: challenges and solutions

The pretreatment and the enzymatic saccharification are the key steps in the extraction of fermentable sugars for further valorization of lignocellulosic biomass (LCB) to biofuels and value-added products via biochemical and/or chemical conversion routes. Due to low density and high-water absorption capacity of LCB, the large volume of water is required for its processing. Integration of pretreatment, saccharification, and co-fermentation has succeeded and well-reported in the literature. However, there are only few reports on extraction of fermentable sugars from LCB with high biomass loading (>10% Total solids-TS) feasible to industrial reality. Furthermore, the development of enzymatic cocktails can overcome technology hurdles with high biomass loading. Hence, a better understanding of constraints involved in the development of technology with high biomass loading can result in an economical and efficient yield of fermentable sugars for the production of biofuels and bio-chemicals with viable titer, rate, and yield (TRY) at industrial scale. The present review aims to provide a critical assessment on the production of fermentable sugars from lignocelluloses with high solid biomass loading. The impact of inhibitors produced during both pretreatment and saccharification has been elucidated. Moreover, the limitations imposed by high solid loading on efficient mass transfer during saccharification process have been elaborated.

Quantitative analysis of biopolymers in lignocellulosic biomass feedstocks via laser-assisted micro-pyrolysis flowing atmospheric-pressure afterglow high-resolution ambient mass spectrometry

Herein, a diode laser-assisted micro-pyrolysis (LAMP) technique coupled with FAPA high resolution mass spectrometry (HRMS) is demonstrated for fast chemical characterization of lignocellulosic biomass feedstocks. The solid lignocellulosic biomass can be analyzed directly with minimal sample preparation. The mass spectra of the pyrolysis products are interpreted with the aid of data visualization tools such as Kendrick mass defect (KMD) plots and van Krevelen plots. Furthermore, quantitation of lignin/cellulose/hemicellulose, sugar contents of glucan/xylan/galactan/arabinan and lignin monomeric unit S/G is achieved with good accuracy and precision, through multivariate analysis methods, including partial least squares regression (PLSR) and support vector regression (SVR).

Tween 80 reversed adverse effects of combined autohydrolysis and p-toluenesulfonic acid pretreatment on enzymatic hydrolysis of poplar

In this study, a combined pretreatment involving autohydrolysis and p-toluenesulfonic acid (p-TsOH) was performed on poplar to coproduce xylooligosaccharides (XOSs) and monosaccharides. The autohydrolysis (180 °C, 30 min) yielded 53.2 % XOS and enhanced the delignification efficiency in the subsequent p-TsOH treatment. Furthermore, considerably high glucan contents (64.1 %∼83.1 %) were achieved in the combined pretreated substrates. However, their enzymatic digestibilities were found to be extremely poor (9.6 %∼14.2 %), which were even lower than the single p-TsOH pretreated substrates (10.2 %∼35.8 %). The underlying reasons were revealed by systematically investigating the effects of the single and combined pretreatment strategies on substrate properties. Moreover, the Tween 80 addition successfully reversed the adverse effects of combined pretreatment on the enzymatic hydrolysis, achieving a high glucose yield of 99.3 % at an enzyme loading of 10 filter paper units/g (FPU/g) glucan. These results deepen the understanding of the synergy of combined pretreatment on biomass fractionation and enzymatic saccharification.

Solar reforming as an emerging technology for circular chemical industries

The adverse environmental impacts of greenhouse gas emissions and persistent waste accumulation are driving the demand for sustainable approaches to clean-energy production and waste recycling. By coupling the thermodynamically favourable oxidation of waste-derived organic carbon streams with fuel-forming reduction reactions suitable for producing clean hydrogen or converting CO2 to fuels, solar reforming simultaneously valorizes waste and generates useful chemical products. With appropriate light harvesting, catalyst design, device configurations and waste pre-treatment strategies, a range of sustainable fuels and value-added chemicals can already be selectively produced from diverse waste feedstocks, including biomass and plastics, demonstrating the potential of solar-powered upcycling plants. This Review highlights solar reforming as an emerging technology that is currently transitioning from fundamental research towards practical application. We investigate the chemistry and compatibility of waste pre-treatment, introduce process classifications, explore the mechanisms of different solar reforming technologies, and suggest appropriate concepts, metrics and pathways for various deployment scenarios in a net-zero-carbon future.

Modified Biomass-Reinforced Polylactic Acid Composites

Polylactic acid (PLA), as a renewable and biodegradable green polymer material, is hailed as one of the most promising biopolymers capable of replacing petroleum-derived polymers for industrial applications. Nevertheless, its limited toughness, thermal stability, and barrier properties have restricted its extensive application. To address these drawbacks in PLA, research efforts have primarily focused on enhancing its properties through copolymerization, blending, and plasticization. Notably, the blending of modified biomass with PLA is expected not only to effectively improve its deficiencies but also to maintain its biodegradability, creating a fully green composite with substantial developmental prospects. This review provides a comprehensive overview of modified biomass-reinforced PLA, with an emphasis on the improvements in PLA's mechanical properties, thermal stability, and barrier properties achieved through modified cellulose, lignin, and starch. At the end of the article, a brief exploration of plasma modification of biomass is presented and provides a promising outlook for the application of reinforced PLA composite materials in the future. This review provides valuable insights regarding the path towards enhancing PLA.

Structural elucidation and targeted valorization of untractable lignin from pre-hydrolysis liquor of xylose production via a simple and robust separation approach

Effective separation of lignin macromolecules from the xylose pre-hydrolysates (XPH) during the xylose production, thus optimizing the separation and purification process of xylose, is of great significance for reducing the production costs, achieving the high value-added utilization of lignin and increasing the industrial revenue. In this study, a simple and robust method (pH adjustment) for the separation of lignin from XPH was proposed and systematically compared with the conventional acid-promoted lignin precipitation method. The results showed that the lignin removal ratio (up to 60.34 %) of this simple method was higher than that of the conventional method, and the proposed method eliminated the necessity of heating and specialized equipment, which greatly reduced the separation cost. Meanwhile, this simple method does not destroy the components in XPH (especially xylose), ensuring the yield of the target product. On the other hand, the obtained lignin was nano-scale with less condensed structures, which also possessed small molecular weights with narrow distribution, excellent antioxidant activity (8-14 times higher than commercial antioxidants) and UV protection properties. In conclusion, the proposed simple separation method could effectively separate lignin from XPH at low cost, and the obtained lignin had potential commercial applications, which would further enhance the overall profitability of industrial production.

Lignin Extraction by Using Two-Step Fractionation: A Review

Lignocellulosic biomass represents the most abundant renewable carbon source on earth and is already used for energy and biofuel production. The pivotal step in the conversion process involving lignocellulosic biomass is pretreatment, which aims to disrupt the lignocellulose matrix. For effective pretreatment, a comprehensive understanding of the intricate structure of lignocellulose and its compositional properties during component disintegration and subsequent conversion is essential. The presence of lignin-carbohydrate complexes and covalent interactions between them within the lignocellulosic matrix confers a distinctively labile nature to hemicellulose. Meanwhile, the recalcitrant characteristics of lignin pose challenges in the fractionation process, particularly during delignification. Delignification is a critical step that directly impacts the purity of lignin and facilitates the breakdown of bonds involving lignin and lignin-carbohydrate complexes surrounding cellulose. This article discusses a two-step fractionation approach for efficient lignin extraction, providing viable paths for lignin-based valorization described in the literature. This approach allows for the creation of individual process streams for each component, tailored to extract their corresponding compounds.

Bio-Based Alkali Lignin Cooperative Systems for Improving the Flame Retardant and Mechanical Properties of Rigid Polyurethane Foam

Lignin was utilized as an environmentally friendly synergistic agent to augment the fire resistance and mechanical characteristics of rigid polyurethane foam (PUF)/melamine-formaldehyde resin ammonium polyphosphate (MFAPP). The incorporation of lignin significantly enhanced the charring capability and flame retardancy of PUF/MFAPP. Specifically, PUF/MFAPP12/A-lignin3 exhibited a charring residue of 23.1% at 800 °C, accompanied by an increase in the limiting oxygen index (LOI) to 23.1%, resulting in a UL-94 V-0 rating. The cone calorimeter test (CCT) revealed that the peak heat release rate (PHRR), total heat release (THR), smoke production rate (SPR), and total smoke production (TSP) values of PUF/MFAPP12/A-lignin3 were all lower than for pure PUF. MFAPP and alkali lignin exerted a noticeable influence on the physical and mechanical properties, leading to increases in density (35.4 kg/m3), thermal conductivity (32.68 mW/(m·K)), and compressive strength (160.5 kPa). Observations of the morphology and elemental composition of char residues after combustion indicated the formation of an intact, thick, and continuous char layer enriched with nitrogen and phosphorus elements, which acted as a protective shield for the underlying foam.

Use of biochar and a post-coagulation effluent as an adsorbent of malachite green, beneficial bacteria carrier, and seedling substrate for plants belonging to the poaceae family

Wastewater treatment plants produce solid and semi-solid sludge, which treatment minimises secondary environmental pollution because of wastewater treatment and obtaining new bioproducts. For this reason, in this paper, the co-pyrolysis of biogenic biomasses recovered from a biological reactor with immobilised fungal and bacterial biomass and a tertiary reactor with Chlorella sp. used for dye-contaminated wastewater treatment was carried out. Biogenic biomasses mixed with pine bark allowed the production and characterisation of two types of biochar. The raw material and biochar were on the "in vitro" germination of Lolium sp. seeds, followed by adsorption studies for malachite green (MG) dye using the raw material and the biochar. Results showed that using 60 mg L-1 of a cationic coagulant at pH 6.5 allowed for the recovery of more than 90% of the microalgae after 50 min of processing. Two biochar resulted: BC300, at pH 5.08 ± 0.08 and BC500, at pH 6.78 ± 0.01. The raw material and both biochars were co-inoculated with growth-promoting bacteria; their viabilities ranged from 1.7 × 106 ± 1.0 × 101 to 7.5 × 108 ± 6.0 × 102 CFU g-1 for total heterotrophic, nitrogen-fixing and phosphate-solubilising bacteria. Re-use tests on Lolium sp. seed germination showed that with the post-coagulation effluent, the germination was 100%, while with the biochar, with and without beneficial bacteria, the germination was 98 and 99%, respectively. Finally, BC500 adsorbed the highest percentage of malachite green at pH 4.0, obtaining qecal values of 0.5249 mg g-1 (R2: 0.9875) with the pseudo-second-order model.

Supplementary Information

The online version contains supplementary material available at 10.1007/s13205-023-03766-x.

Enzymatic digestibility of lignocellulosic wood biomass: Effect of enzyme treatment in supercritical carbon dioxide and biomass pretreatment

Energy and resource intensive mechanical and chemical pretreatment along with the use of hazardous chemicals are major bottlenecks in widespread lignocellulosic biomass utilization. Herein, the study investigated different pretreatment methods on spruce wood namely supercritical CO2 (scCO2) pretreatment, ultrasound-assisted alkaline pretreatment, and acetosolv pulping-alkaline hydrogen peroxide bleaching, to enhance the enzymatic digestibility of wood using optimized enzyme cocktail. Also, the effect of scCO2 pretreatment on enzyme cocktail was investigated after optimizing the concentration and temperature of cellulolytic enzymes. The impact of scCO2 and ultrasound-assisted alkaline pretreatments of wood were insignificant for the enzymatic digestibility, and acetosolv pulping-alkaline hydrogen peroxide bleaching was the most effective pretreatment that showed the release of total reducing sugar yield (TRS) of ∼95.0 wt% of total hydrolyzable sugars (THS) in enzymatic hydrolysis. The optimized enzyme cocktail showed higher yield than individual enzymes with degree of synergism 1.34 among the enzymes, and scCO2 pretreatment of cocktail for 0.5-1.0 h at 10.0-22.0 MPa and 38.0-54.0 °C had insignificant effect on the enzyme's primary and global secondary structure of cocktail and its activity.

Green chemical and hybrid enzymatic pretreatments for lignocellulosic biorefineries: Mechanism and challenges

The greener chemical and enzymatic pretreatments for lignocellulosic biomasses are portraying a crucial role owing to their recalcitrant nature. Traditional pretreatments lead to partial degradation of lignin and hemicellulose moieties from the pretreated biomass. But it still restricts the enzyme accessibility for the digestibility towards the celluloses and the interaction of lignin-enzymes, nonproductively. Moreover, incursion of certain special chemical treatments and other lignin sulfonation techniques to the enzymatic pretreatment (hybrid enzymatic pretreatment) enhances the lignin structural modification, solubilization of the hemicelluloses and both saccharification and fermentation processes (SAF). This article concentrates on recent developments in various chemical and hybrid enzymatic pretreatments on biomass materials with their mode of activities. Furthermore, the issues on strategies of the existing pretreatments towards their industrial applications are highlighted, which could lead to innovative ideas to overcome the challenges and give guideline for the researchers towards the lignocellulosic biorefineries.

Physicochemical Pretreatment of Vietnamosasa pusilla for Bioethanol and Xylitol Production

The consumption of fossil fuels has resulted in severe environmental consequences, including greenhouse gas emissions and climate change. Therefore, transitioning to alternative energy sources, such as cellulosic ethanol, is a promising strategy for reducing environmental impacts and promoting sustainable low-carbon energy. Vietnamosasa pusilla, an invasive weed, has been recognized as a high potential feedstock for sugar-based biorefineries due to its high total carbohydrate content, including glucan (48.1 ± 0.3%) and xylan (19.2 ± 0.4%). This study aimed to examine the impact of NaOH pretreatment-assisted autoclaving on V. pusilla feedstock. The V. pusilla enzymatic hydrolysate was used as a substrate for bioethanol and xylitol synthesis. After treating the feedstock with varying concentrations of NaOH at different temperatures, the glucose and xylose recovery yields were substantially higher than those of the untreated material. The hydrolysate generated by enzymatic hydrolysis was fermented into bioethanol using Saccharomyces cerevisiae TISTR 5339. The liquid byproduct of ethanol production was utilized by Candida tropicalis TISTR 5171 to generate xylitol. The results of this study indicate that the six- and five-carbon sugars of V. pusilla biomass have great potential for the production of two value-added products (bioethanol and xylitol).

Organosolv Pretreatment of Cocoa Pod Husks: Isolation, Analysis, and Use of Lignin from an Abundant Waste Product

Cocoa pod husks (CPHs) represent an underutilized component of the chocolate manufacturing process. While industry's current focus is understandably on the cocoa beans, the husks make up around 75 wt % of the fruit. Previous studies have been dominated by the carbohydrate polymers present in CPHs, but this work highlights the presence of the biopolymer lignin in this biomass. An optimized organosolv lignin isolation protocol was developed, delivering significant practical improvements. This new protocol may also prove to be useful for agricultural waste-derived biomasses in general. NMR analysis of the high quality lignin led to an improved structural understanding, with evidence provided to support deacetylation of the lignin occurring during the optimized pretreatment. Chemical transformation, using a tosylation, azidation, copper-catalyzed click protocol, delivered a modified lignin oligomer with an organophosphorus motif attached. Thermogravimetric analysis was used to demonstrate the oligomer's potential as a flame-retardant. Preliminary analysis of the other product streams isolated from the CPHs was also carried out.

One-step conversion of corn stalk to glucose and furfural in molten salt hydrate/organic solvent biphasic system

An effective approach for glucose and furfural production by converting cellulose and hemicelluloses from corn stalk in a biphasic system of molten salt hydrate (MSH) and organic solvent using H2SO4 as catalyst was reported. Results showed that the system with LiBr·3H2O and dichloromethane (DCM) had excellent performance in cellulose and hemicelluloses conversion. Under the optimal reaction conditions (corn stalk:LiBr·3H2O:DCM ratio = 0.35:10:20 g/mL/mL, 0.05 mol/L H2SO4, 120 °C, 90 min), 58.9% glucose and 72.5% furfural were yielded. Meanwhile, lignin was obviously depolymerized by the cleavage of β-O-4' linkages and fractionated with high purity and low molecular weight for potential coproducts. Fluorescence microscopy and confocal Raman microscope displayed that the LiBr·3H2O/DCM treatment caused decreasing intensities in carbohydrate and lignin, suggesting the degradation of the main components of biomass. This research provided a promising biorefinery technology for the comprehensive utilization of corn stalk.

Is a floodplain forest a valuable source for lignin-degrading anaerobic microbial communities: A metagenomic approach

Lignin is one of the most substantial obstacles in the evaluation of lignocellulosic compounds. Although there are numerous approaches for the enhancement of lignin digestion in the literature, there has yet to be an optimized system to date. In this study, samples taken from Igneada floodplain forests were enriched anaerobically at 25 °C and 37 °C, with alkali lignin as the sole carbon source. The activity of the anaerobic lignin-degrading microbial consortium was detected more efficiently at 37 °C, where biogas production exceeded 3.5 mLgas/mLmedium. It was observed that the microbial community initially dominated by Proteobacteria (around 60%) changed completely after enrichment and was led by members of the Firmicutes phylum (up to 90%). The dominant species (Sporomusa termitida, Desulfitobacterium hafniense, Citrobacter freundii, Citrobacter portucalensis, Alkalibacter rhizosphaerae, and Gudongella oleilytica) occupying more than 50% in the final enrichment culture were only around 2% in the raw samples. Therefore, this study, one of the few in which enriched environmental samples were sequenced using MinION, demonstrated that longoses are exceptional reservoirs for lignin-digesting anaerobic microorganisms.

Bonding wood with uncondensed lignins as adhesives

Plywood is widely used in construction, such as for flooring and interior walls, as well as in the manufacture of household items such as furniture and cabinets. Such items are made of wood veneers that are bonded together with adhesives such as urea-formaldehyde and phenol-formaldehyde resins1,2. Researchers in academia and industry have long aimed to synthesize lignin-phenol-formaldehyde resin adhesives using biomass-derived lignin, a phenolic polymer that can be used to substitute the petroleum-derived phenol3-6. However, lignin-phenol-formaldehyde resin adhesives are less attractive to plywood manufacturers than urea-formaldehyde and phenol-formaldehyde resins owing to their appearance and cost. Here we report a simple and practical strategy for preparing lignin-based wood adhesives from lignocellulosic biomass. Our strategy involves separation of uncondensed or slightly condensed lignins from biomass followed by direct application of a suspension of the lignin and water as an adhesive on wood veneers. Plywood products with superior performances could be prepared with such lignin adhesives at a wide range of hot-pressing temperatures, enabling the use of these adhesives as promising alternatives to traditional wood adhesives in different market segments. Mechanistic studies indicate that the adhesion mechanism of such lignin adhesives may involve softening of lignin by water, filling of vessels with softened lignin and crosslinking of lignins in adhesives with those in the cell wall.

Strategic biomodification for raw plant-based pretreatment biorefining toward sustainable chemistry

Plant-based pretreatment biorefining is the initial triggering process in biomass-conversion to bio-based chemical products. In view of chemical sustainability, the raw plant-based pretreatment biorefining process is more favorable than the fossil-based one. Its direct use contributes to reducing CO2 emissions and the production cost of the target products by eliminating costly steps, such as the separation and purification of intermediates. Three types of feedstock plant resources have been utilized as raw plant feedstock sources, such as: lignocellulosic, starchy, and inulin-rich feedstock plants. These plant sources can be directly used for bio-based chemical products. To enhance the efficiency of their pretreatment biorefining process, well-designed biomodification schemes are discussed in this review to afford important information on useful biomodification approaches. For lignocellulosic feedstock plants, the enzymes and regulatory elements involved in lignin reduction are discussed using: COMT, GAUT4, CSE, PvMYB4 repressor, etc. For inulin-rich feedstock plants, 1-SST, 1-FFT, 1-FEH, and endoinulinase are illustrated in relation with the reduction of chain length of inulin polymer. For starchy feedstock plants, their biomodification is targeted to enhancing the depolymerization efficiency of starch to glucose monomer units. For this biomodification target, six candidates are discussed. These are SBE I, SBE IIa, SBE IIb, GBSS I, PTSTI, GWD 1, and PTSTI. The biomodification strategies discussed here promise to be conducive to enhancing the efficiency of the plant-based pretreatment biorefining process.

Advances on Cellulose Manufacture in Biphasic Reaction Media

Cellulose is produced industrially by the kraft and sulfite processes. The evolution of these technologies in biorefineries is driven by the need to obtain greater added value through the efficient use of raw materials and energy. In this field, organosolv technologies (and within them, those using liquid phases made up of water and one partly miscible organic solvent, known as "biphasic fractionation" in reference to the number of liquid phases) represent an alternative that is receiving increasing interest. This study considers basic aspects of the composition of lignocellulosic materials, describes the fundamentals of industrial cellulose pulp production processes, introduces the organosolv methods, and comprehensively reviews published results on organosolv fractionation based on the use of media containing water and an immiscible solvent (1-butanol, 1-pentanol or 2-methyltetrahydrofuran). Special attention is devoted to aspects related to cellulose recovery and fractionation selectivity, measured through the amount and composition of the treated solids.

Effect of Chemical and Steam Explosion Pulping on the Physical and Mechanical Properties of Sugarcane Straw Pulp Trays

Sugarcane straw fiber (SSF) samples were prepared by chemical pulping (CP) and steam explosion (STE). CP (5, 10, 15% NaOH + 0.2% w/w anthraquinone at 121 °C for 1 h) and STE pressure (1.77, 1.96, and 2.16 MPa at 220 °C for 4 min) SSF trays were molded with a hydraulic hot-press machine at 120 °C, 7 min, and 1.72 MPa. The yield (%) of SSF from STE (54-60% dry basis (db.)) was higher than CP (32-48% db.). STE trays had greater tensile strength than CP. However, STE's elongation and compression strength was lower than CP tray samples. The trays made from SSF using STE had less swelling in thickness, longer water wetting time, and a higher water contact angle than those made from CP. The micrographs displayed a smaller size of SSF obtained in STE than the CP. The appearance and area of peaks in ATR-FTIR spectra and XRD diffractograms, respectively, revealed that the STE trays had a larger residual lignin content from the lignin study and a lower crystallinity index than the CP trays. Moreover, the lightness values of the STE trays were lower than those of the CP trays due to lignin retention. The study results indicate that CP is the preferred method for producing SSF packaging material with high flexibility and fiber purity. However, when considering the specific SF of 4.28, the STE treatment showed superior physical and mechanical properties compared to CP. This suggests that STE could be an excellent alternative green pulping technique for producing durable biobased trays. Overall, the findings highlight the potential of STE as a viable option for obtaining trays with desirable characteristics, providing a sustainable and efficient approach to tray production.

Photoreforming for Lignin Upgrading: A Critical Review

Photoreforming of lignocellulosic biomass to simultaneously produce gas fuels and value-added chemicals has gradually emerged as a promising strategy to alleviate the fossil fuels crisis. Compared to cellulose and hemicellulose, the exploitation and utilization of lignin via photoreforming are still at the early and more exciting stages. This Review systematically summarizes the latest progress on the photoreforming of lignin-derived model components and "real" lignin, aiming to provide insights for lignin photocatalytic valorization from fundamental to industrial applications. Considering the complexity of lignin physicochemical properties, related analytic methods are also introduced to characterize lignin photocatalytic conversion and product distribution. We finally put forward the challenges and perspective of lignin photoreforming, hoping to provide some guidance to valorize biomass into value-added chemicals and fuels via a mild photoreforming process in the future.

Efficient production of high concentration monosaccharides and ethanol from poplar wood after delignification and deacetylation

Efficient enzymatic hydrolysis is required for production of high concentration monosaccharides and ethanol. The lignin and acetyl group in poplar can limit the enzymatic hydrolysis. However, the effect of delignification combined with deacetylation on the saccharification of poplar for high concentration monosaccharides was not clear. Herein, hydrogen peroxide-acetic acid (HPAA) was used for delignification and sodium hydroxide was used for deacetylation to enhance the hydrolyzability of poplar. Delignification with 60% HPAA at 80 °C could remove 81.9% lignin. Acetyl group was completely removed with 0.5% NaOH at 60 °C. After saccharification, 318.1 g/L monosaccharides were obtained with a poplar loading of 35% (w/v). After simultaneous saccharification and fermentation, 114.9 g/L bioethanol was gained from delignified and deacetylated poplar. Those results showed the highest monosaccharides and ethanol concentrations in reported research. This developed strategy with relatively low temperature could effectively improve the production of high concentration monosaccharide and ethanol from poplar.

Multifunctional catalyst-assisted sustainable reformation of lignocellulosic biomass into environmentally friendly biofuel and value-added chemicals

Rapid urbanization is increasing the world's energy demand, making it necessary to develop alternative energy sources. These growing energy needs can be met by the efficient energy conversion of biomass, which can be done by various means. The use of effective catalysts to transform different types of biomasses will be a paradigm change on the road to the worldwide goal of economic sustainability and environmental protection. The development of alternative energy from biomass is not easy, due to the uneven and complex components present in lignocellulose; accordingly, the majority of biomass is currently processed as waste. The problems may be overcome by the design of multifunctional catalysts, offering adequate control over product selectivity and substrate activation. Hence, this review describes recent developments involving various catalysts such as metallic oxides, supported metal or composite metal oxides, char-based and carbon-based substances, metal carbides and zeolites, with reference to the catalytic conversion of biomass including cellulose, hemicellulose, biomass tar, lignin and their derivative compounds into useful products, including bio-oil, gases, hydrocarbons, and fuels. The main aim is to provide an overview of the latest work on the use of catalysts for successful conversion of biomass. The review ends with conclusions and suggestions for future research, which will assist researchers in utilizing these catalysts for the safe conversion of biomass into valuable chemicals and other products.

Conditioning of pretreated birch by liquid-liquid organic extractions to improve yeast fermentability and enzymatic digestibility

By-products from hydrothermal pretreatment of lignocellulosic biomass inhibit enzymatic saccharification and microbial fermentation. Three long-chain organic extractants (Alamine 336, Aliquat 336 and Cyanex 921) were compared to two conventional organic solvents (ethyl acetate and xylene) with regard to conditioning of birch wood pretreatment liquid (BWPL) for improved fermentation and saccharification. In the fermentation experiments, extraction with Cyanex 921 resulted in the best ethanol yield, 0.34 ± 0.02 g g^-1 on initial fermentable sugars. Extraction with xylene also resulted in a relatively high yield, 0.29 ± 0.02 g g^-1, while cultures consisting of untreated BWPL and BWPL treated with the other extractants exhibited no ethanol formation. Aliquat 336 was most efficient with regard to removing by-products, but the residual Aliquat after the extraction was toxic to yeast cells. Enzymatic digestibility increased by 19-33% after extraction with the long-chain organic extractants. The investigation demonstrates that conditioning with long-chain organic extractants has the potential to relieve inhibition of both enzymes and microbes.

Cell wall composition and biomass saccharification potential of Sida hermaphrodita differ between genetically distant accessions

Due to its ample production of lignocellulosic biomass, Sida hermaphrodita (Sida), a perennial forb, is considered a valuable raw material for biorefinery processes. The recalcitrant nature of Sida lignocellulosic biomass towards pretreatment and fractionation processes has previously been studied. However, Sida is a non-domesticated species and here we aimed at expanding the potential of such plants in terms of their processability for downstream processes by making use of the natural variety of Sida. To achieve this goal, we established a collection comprising 16 different Sida accessions obtained from North America and Europe. First, we asked whether their cell wall characteristics are reflected in genetic distance or geographical distribution, respectively. A genotyping-by-sequencing (GBS) analysis resulting in a phylogenic tree based on 751 Single Nucleotide Polymorphisms (SNPs), revealed a high genetic diversity and a clear separation between accessions collected in North America and Europe. Further, all three North American accessions were separated from each other. Of the eleven European accessions, five form individual groups and six others belong to a single group. Clonal plants of seven selected accessions of American and European origin were produced and cultivated under greenhouse conditions and the resulting plant material was used for in-depth wet-chemical and spectroscopic cell wall characterization. Two accessions with contrasting cell wall characteristics were then selected and processed using the OrganoCat technology. Results of the different product yields and chemical compositions are reported. Overall, cell wall analyses revealed contrasting clusters regarding these main components between the accessions that can be related to genetic and, partly, geographical distance. Phenotypically, the accessions clustered into two groups that are not entirely overlapping with geographical origin. These results can be the basis for a targeted selection or cultivation of Sida accessions for biorefinery approaches.

Fractionation of Aspen Wood to Produce Microcrystalline, Microfibrillated and Nanofibrillated Celluloses, Xylan and Ethanollignin

A new method for extractive-catalytic fractionation of aspen wood to produce microcrystalline (MCC), microfibrillated (MFC), nanofibrilllated (NFC) celluloses, xylan, and ethanollignin is suggested in order to utilize all of the main components of wood biomass. Xylan is obtained with a yield of 10.2 wt.% via aqueous alkali extraction at room temperature. Ethanollignin was obtained with a yield of 11.2 wt.% via extraction with 60% ethanol from the xylan-free wood at 190 °C. The lignocellulose residue formed after the extraction of xylan and ethanollignin was subjected to catalytic peroxide delignification in the acetic acid-water medium at 100 °C in order to obtain microcrystalline cellulose. MCC is hydrolyzed with 56% sulfuric acid and treated with ultrasound to produce microfibrillated cellulose and nanofibrillated cellulose. The yields of MFC and NFC were 14.4 and 19.0 wt.%, respectively. The average hydrodynamic diameter of NFC particles was 36.6 nm, the crystallinity index was 0.86, and the average zeta-potential was 41.5 mV. The composition and structure of xylan, ethanollignin, cellulose product, MCC, MFC, and NFC obtained from aspen wood were characterized using elemental and chemical analysis, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) analyses, Gas chromatography (GC), Gel permeation-chromatography (GPC), Scanning electron microscopy (SEM), Atomic force microscopy (AFM), Dynamic light scattering (DLS), Thermal gravimetric analysis (TGA).