Multidimensional approaches of biogas production and up-gradation: Opportunities and challenges

Increase in potato yield by the combined application of biochar and organic fertilizer: key role of rhizosphere microbial diversity

Purpose

The large-scale planting of potatoes leads to soil degradation, thus limiting the potato yield. An effective method of improving soil quality involves the combined application of biochar and organic fertilizer. However, the proportion of biochar and organic fertilizer at which potato yield can be improved, as well as the improvement mechanism, remain unclear.

Methods

A combined application experiment involving biochar (B) and organic fertilizer (O) with four concentration gradients was conducted using the equal carbon ratio method. On this basis, rhizosphere soil fertility, bacterial community composition, and bacterial diversity in potato crops, as well as the potato yield difference under different combined application ratios, were investigated. Then, the direct and indirect effects of these factors on potato yield were analyzed.

Results

The results suggest that soil fertility was improved by the combined application of biochar and organic fertilizer, with the best effect being achieved at a ratio of B:O=1:2. The dominant bacterial communities in the potato rhizosphere included Proteobacteria, Actinobacteria, Gemmatimonadetes, Chloroflexi, and Bacteroidetes. When compared to the control, the relative abundance and diversity index of soil bacteria were significantly improved by the treatment at B:O=1:2, which exerted a stronger effect on improving the relative abundance of beneficial bacteria. Soil available phosphorus (AP), soil pH (SpH), and soil organic carbon (SOC) explained 47.52% of the variation in bacterial composition. Among them, the main factor was the content of soil available nutrients, while SpH generated the weakest effect. The bacterial diversity index showed a significant positive correlation with soil AP, SOC, available potassium (AK), total nitrogen (TN), and C/N ratio, and a significant negative correlation with SpH. Bacterial diversity directly affected the potato yield, while soil fertility indirectly affected potato yield by influencing the soil bacterial diversity.

Conclusion

The combined application of biochar and organic fertilizer elevates potato yield mainly by improving the diversity of bacterial communities in potato rhizosphere soil, especially the combined application of biochar and organic fertilizer at a 1:2 ratio (biochar 0.66 t ha-1+organic fertilizer 4.46 t ha-1), which made the largest contribution to increasing potato yield.

Adsorption Mechanism and Regeneration Performance of Calcined Zeolites for Hydrogen Sulfide and Its Application

Hydrogen sulfide (H2S) is a very toxic, acidic, and odorous gas. In this study, a calcined zeolite was used to investigate the adsorption performance of H2S. Among particle size, calcination temperature and time calcination temperature and time had significant effects on the adsorption capacity of H2S on the zeolite. The optimal calcination conditions for the zeolite were 332 °C, 1.8 h, and 10-20 mm size, and the maximum adsorption capacity of H2S was approximately 6219 mg kg-1. Calcination could broaden the channels, remove the adsorbed gases and impurities on the surface of zeolites, and increase the average pore size and point of zero net charge. As the zeolite adsorbed to saturation, it could be regenerated at the temperatures between 200 and 350 °C for 0.5 h. Compared with the natural zeolite, the adsorption capacities of dimethyl disulfide, dimethyl sulfide, toluene, CH3SH, CS2, CO2, and H2S were significantly higher on the calcined zeolite, while the adsorption capacity of CH4 was lower on the calcined zeolite. A gas treatment system by a temperature swing adsorption-regeneration process on honeycomb rotors with calcined zeolites was proposed. These findings are helpful for developing techniques for removing gas pollutants such as volatile sulfur compounds and volatile organic compounds to purify biogas and to limited toxic concentrations in the working environment.

Ruminal content biochar supplementation for enhanced biomethanation of rice straw: Focusing on biochar characterization and dose optimization

Anaerobic digestion (AD) of agricultural wastes is a promising approach for energy recovery and crop residue management. However, its recalcitrant chemical structure hinders microbial hydrolysis and reduces biomethane production under AD. Biochar supplementation has been proven to promote the digestibility and biomethanation of lignocellulosic substrates. Therefore, this study investigated the influence of different pyrolysis temperatures (450 °C, 550 °C, and 650 °C) on the physicochemical properties of biochar. Furthermore, the impact of ruminal content biochar supplementation (1 %, 2 %, and 3 %) on the AD of rice straw with rumen fluid as inoculum has been investigated. The ruminal content biochar (RUCB) supplemented reactors showed an increment in biomethane yield and the highest cumulative biomethane yield 243.11 mL/g volatile solids (VS)) was recorded at 2 % RUCB supplementation, followed by 227.12 mL/g VS at 1 % RUCB supplementation and 162.86 mL/g VS at 3 % RUCB supplementation (P > 0.05). Compared to the control reactors (128.68 mL/g VS), RUCB supplemented reactors exhibited 1.88-fold, 1.76-fold, and 1.26-fold increments in biomethane yield due to pH stabilization and facilitation of microbial biofilm formation on the biochar. The correlation analysis showed that biomethane production is positively correlated with VS reduction (R2 = 0.9852). This study proposed a potential strategy to utilize ruminal content waste as a feedstock for biochar production and its application in AD for accelerating the biomethanation of rice straw.

Prospect of denitrifying anaerobic methane oxidation (DAMO) application on wastewater treatment and biogas recycling utilization

Old-fashioned wastewater treatments for nitrogen depend on heterotrophic denitrification process. It would utilize extra organic carbon source as electron donors when the C/N of domestic wastewater was too low to ensure heterotrophic denitrification process. It would lead to non-compliance with carbon reduction targets and impose an economic burden on wastewater treatment. Denitrifying anaerobic methane oxidation (DAMO), which could utilize methane serving as electron donors to replace traditional organic carbon (methanol or sodium acetate), supplies a novel approach for wastewater treatment. As the primary component of biogas, methane is an inexpensive carbon source. With anaerobic digestion becoming increasingly popular for sludge reduction in wastewater treatment plants (WWTPs), efficient biogas utilization through DAMO can offer an environmentally friendly option for in-situ biogas recycling. Here, we reviewed the metabolic principle and relevant research for DAMO and biogas recycling utilization, outlining the prospect of employing DAMO for wastewater treatment and biogas recycling utilization in WWTPs. The application of DAMO provides a new focal point for enhancing efficiency and sustainability in WWTPs.

Insights into the recent advances of agro-industrial waste valorization for sustainable biogas production

Recent years have seen a transition to a sustainable circular economy model that uses agro-industrial waste biomass waste to produce energy while reducing trash and greenhouse gas emissions. Biogas production from lignocellulosic biomass (LCB) is an alternative option in the hunt for clean and renewable fuels. Different approaches are employed to transform the LCB to biogas, including pretreatment, anaerobic digestion (AD), and biogas upgradation to biomethane. To maintain process stability and improve AD performance, machine learning (ML) tools are being applied in real-time monitoring, predicting, and optimizing the biogas production process. An environmental life cycle assessment approach for biogas production systems is essential to calculate greenhouse gas emissions. The current review presents a detailed overview of the utilization of agro-waste for sustainable biogas production. Different methods of waste biomass processing and valorization are discussed that contribute towards developing an efficient agro-waste to biogas-based circular economy.

A thematic review on livestock manure treatment strategies focusing on thermochemical conversion

Livestock manure (LSM) management is emerging as a challenge due to increasing livestock consumption. Owing to the decreased agricultural land area, it is necessary to ensure LSM utilization in non-agricultural fields. LSM can be a valuable resource if managed as a circulating resource. This study discusses research trends based on a literature review and classifies LSM treatments. The analysis of each treatment is presented according to research trends, and implications for the future LSM processing are discussed. "Biological treatment" accounted for the largest portion at 48%, "manure management," which suggests improvement in manure treatment through systematic thinking or LSM management practices, accounted for 16%, and "thermochemical conversion" accounted for 11%. In addition, "life cycle assessment (LCA) research," "solid-liquid separation approach," and "nutrient-recovery/losses" were derived. Studies on biological treatments are increasing. Although anaerobic digestion (AD) is the most used method, it has the disadvantages of long processing time and waste generation after processing. As a key supplement, thermochemical conversion (TCC) technology, which could overcome the disadvantages of AD, was reviewed.

Enhancing the production of volatile fatty acids by potassium permanganate from wasted sewage sludge: A batch test experiment

Recovering resources from wastewater treatment is vital for the transition from a linear to a circular economy model in the water sector. Volatile Fatty Acids (VFAs) are valuable products among the possible recovered resources. This study investigates the influence of potassium permanganate (KMnO4) addition during acidogenic fermentation of waste activated sludge for enhancing VFAs production. Specifically, different fermentation batch tests with and without KMnO4 addition were carried out using two distinctive sewage sludges as feedstocks. Results showed that KMnO4 addition increased the VFAs yield up to 144 and 196 mgCOD/g VSS for the two sludges. When KMnO4 was used as pre-treatment, 55 % of sCOD were VFAs. This latter result was mainly debited to the recalcitrant organics' disruption promoted by the oxidative permanganate ability.

Bioengineering of biowaste to recover bioproducts and bioenergy: A circular economy approach towards sustainable zero-waste environment

The inevitable need for waste valorisation and management has revolutionized the way in which the waste is visualised as a potential biorefinery for various product development rather than offensive trash. Biowaste has emerged as a potential feedstock to produce several value-added products. Bioenergy generation is one of the potential applications originating from the valorisation of biowaste. Bioenergy production requires analysis and optimization of various parameters such as biowaste composition and conversion potential to develop innovative and sustainable technologies for most effective utilization of biowaste with enhanced bioenergy production. In this context, feedstocks, such as food, agriculture, beverage, and municipal solid waste act as promising resources to produce renewable energy. Similarly, the concept of microbial fuel cells employing biowaste has clearly gained research focus in the past few decades. Despite of these potential benefits, the area of bioenergy generation still is in infancy and requires more interdisciplinary research to be sustainable alternatives. This review is aimed at analysing the bioconversion potential of biowaste to renewable energy. The possibility of valorising underutilized biowaste substrates is elaborately presented. In addition, the application and efficiency of microbial fuel cells in utilizing biowaste are described in detail taking into consideration of its great scope. Furthermore, the review addresses the significance bioreactor development for energy production along with major challenges and future prospects in bioenergy production. Based on this review it can be concluded that bioenergy production utilizing biowaste can clearly open new avenues in the field of waste valorisation and energy research. Systematic and strategic developments considering the techno economic feasibilities of this excellent energy generation process will make them a true sustainable alternative for conventional energy sources.

Critical review of biochemical pathways to transformation of waste and biomass into bioenergy

In recent years, biofuel or biogas have become the primary source of bio-energy, providing an alternative to conventionally used energy that can meet the growing energy demand for people all over the world while reducing greenhouse gas emissions. Enzyme hydrolysis in bioethanol production is a critical step in obtaining sugars fermented during the final fermentation process. More efficient enzymes are being researched to provide a more cost-effective technique during enzymatic hydrolysis. The exploitation of microbial catabolic biochemical reactions to produce electric energy can be used for complex renewable biomasses and organic wastes in microbial fuel cells. In hydrolysis methods, a variety of diverse enzyme strategies are used to promote efficient bioethanol production from various lignocellulosic biomasses like agricultural wastes, wood feedstocks, and sea algae. This paper investigates the most recent enzyme hydrolysis pathways, microbial fermentation, microbial fuel cells, and anaerobic digestion in the manufacture of bioethanol/bioenergy from lignocellulose biomass.

Current research trends on emerging contaminants pharmaceutical and personal care products (PPCPs): A comprehensive review

Pharmaceutical and personnel care products (PPCPs) from wastewater are a potential hazard to the human health and wildlife, and their occurrence in wastewater has caught the concern of researchers recently. To deal with PPCPs, various treatment technologies have been evolved such as physical, biological, and chemical methods. Nevertheless, modern and efficient techniques such as advance oxidation processes (AOPs) demand expensive chemicals and energy, which ultimately leads to a high treatment cost. Therefore, integration of chemical techniques with biological processes has been recently suggested to decrease the expenses. Furthermore, combining ozonation with activated carbon (AC) can significantly enhance the removal efficiency. There are some other emerging technologies of lower operational cost like photo-Fenton method and solar radiation-based methods as well as constructed wetland, which are promising. However, feasibility and practicality in pilot-scale have not been estimated for most of these advanced treatment technologies. In this context, the present review work explores the treatment of emerging PPCPs in wastewater, via available conventional, non-conventional, and integrated technologies. Furthermore, this work focused on the state-of-art technologies via an extensive literature search, highlights the limitations and challenges of the prevailing commercial technologies. Finally, this work provides a brief discussion and offers future research directions on technologies needed for treatment of wastewater containing PPCPs, accompanied by techno-economic feasibility assessment.

Maximizing the energy recovery from rice straw through two-step conversion using eggshell-catalytic pyrolysis followed by enhanced anaerobic digestion using calcium-rich biochar

Anaerobic digestion of lignocelluloses for biogas production is greatly restricted by the poor biomass degradability. Herein, a novel approach is suggested to enhance the energy recovery from rice straw through a two-step conversion using eggshell-based catalytic pyrolysis followed by biochar-based anaerobic co-digestion. Pyrolysis with eggshell significantly enhanced the crude bio-oil yield by 4.6 %. Anaerobic digestion of rice straw using 4 g L^-1 of rice straw biochar (RB) showed the highest recorded biogas yield of 503.7 L kg^-1 VS, with 268.6 L kg^-1 VS biomethane yield. However, 4 g L^-1 of calcium-enriched eggshell rice straw biochar (ERB) enhanced the biomethane yield to 281.8 L kg^-1 VS, which represented 95.6 % higher than the control. It was attributed to enhancement of biomethanation, which resulted in 74.5 % maximum recorded biomethane content at the 7th day of anaerobic digestion. Microbial analysis confirmed that Methanosarciniales was the most dominant Archael group in the control (14.84 %), which increased sharply to 73.91 % and 91.66 % after addition of 4 g L^-1 RB and ERB, respectively. The suggested route enhanced the energy recovery in the form of bio-oil and biomethane by 41.6 %.

Waste to catalyst: Role of agricultural waste in water and wastewater treatment

Presently, owing to the rapid development of industrialization and urbanization activities, a huge quantity of wastewater is generated that contain toxic chemical and heavy metals, imposing higher environmental jeopardies and affecting the life of living well-being and the economy of the counties, if not treated appropriately. Subsequently, the advancement in sustainable cost-effective wastewater treatment technology has attracted more attention from policymakers, legislators, and scientific communities. Therefore, the current review intends to highlight the recent development and applications of biochars and/or green nanoparticles (NPs) produced from agricultural waste via green routes in removing the refractory pollutants from water and wastewater. This review also highlights the contemporary application and mechanism of biochar-supported advanced oxidation processes (AOPs) for the removal of organic pollutants in water and wastewater. Although, the fabrication and application of agriculture waste-derived biochar and NPs are considered a greener approach, nevertheless, before scaling up production and application, its toxicological and life-cycle challenges must be taken into account. Furthermore, future efforts should be carried out towards process engineering to enhance the performance of green catalysts to improve the economy of the process.

Machine learning in fermentative biohydrogen production: Advantages, challenges, and applications

Hydrogen can be produced in an environmentally friendly manner through biological processes using a variety of organic waste and biomass as feedstock. However, the complexity of biological processes limits their predictability and reliability, which hinders the scale-up and dissemination. This article reviews contemporary research and perspectives on the application of machine learning in biohydrogen production technology. Several machine learning algorithems have recently been implemented for modeling the nonlinear and complex relationships among operational and performance parameters in biohydrogen production as well as predicting the process performance and microbial population dynamics. Reinforced machine learning methods exhibited precise state prediction and retrieved the underlying kinetics effectively. Machine-learning based prediction was also improved by using microbial sequencing data as input parameters. Further research on machine learning could be instrumental in designing a process control tool to maintain reliable hydrogen production performance and identify connection between the process performance and the microbial population.

The role of biofuels for sustainable MicrogridsF: A path towards carbon neutrality and the green economy

Today, with the progress of technology, the world is facing an increasing growth in power consumption. Since the fuel of most power plants is supplied from fossil fuels, it has caused an increase in global fossil fuel consumption and environmental degradation. ّFurthermore, the volatility of fossil fuel prices and unstable energy security have prompted international organizations and governments to apply policies to restrict fossil fuel use and examine alternatives to fossil fuels. Since biofuels come from renewable sources and are clean fuels, they can be an appropriate alternative to fossil fuels and play a more expansive role in supplying energy for transportation industries, power plants, and heat production systems. Although there is some research about the drawbacks of using fossil fuels and the commendation of using biofuels in various industries such as transportation, the literature lacks a comprehensive study on the evaluation and analysis of the potential of using biofuels instead of conventional fuels in power generation systems. The primary purpose of this study is to evaluate the impact of utilizing biofuels instead of fossil fuels in microgrids to achieve carbon neutrality objectives. Furthermore, this paper reviews previous research studies that have operated biofuels in three categories: solid, liquid, and gas, to generate electricity and analyzes the potential of different biofuels to produce heat and electricity for microgrid power systems. In addition to outlining the present knowledge gaps in this area, this study explores the prospects and threats associated with expanding the use of biofuels in the power production industry and the development of sustainable microgrids. This study indicated that if the technical and economic problems of employing biofuels are overcome, these clean fuels have a great potential to obtain the maximum share of the global power generation market and move toward Net Zero Emissions by 2050 Scenario (NZE) goals.

Balance of total mass and nitrogen fluxes through consecutive digestate processing steps: Two application cases

The high water content and low nutrient concentration of digestate complicate its storage, transportation, and utilization. Subsequent digestate processing can effectively remove water and influence nutrient partitioning among digestate fractions and final products. The current study was carried out to evaluate the performance of two typical digestate processing chains, solid and liquid ones, respectively, and to give practical recommendations for optimization. Two fully operating biogas plants with advanced heat utilization were considered as data sources. The digestate mass flow balance of dry matter (DM), water, total N (TN), and ammonium-N mass flows was performed and the efficiency of the examined processing units was calculated. It was found that solid-liquid separation of raw digestate shifted 73-87% of TN and 60-93% of NH4-N to the liquid phase. Subsequent drying of separated solid fraction removed about 6% of the initial water and required 84% less thermal energy per kg N recovered than the processing of separated liquid. The final product, pellets, contained 14% of initial TN, but only 2% of initial NH4-N as a result of microbial conversion of inorganic N during drying. Vacuum evaporation of separated liquid fraction removed 34% of the initial water and left a DM-rich concentrate. At the same time, an ammonium sulfate solution (ASS) containing 21% of initial TN and 34% of initial NH4-N was produced. Both evaluated processing chains showed specific advantages and challenges. Solid products were characterized by a high share of recalcitrant organic compounds and could serve as a soil improver. Liquid processing concentrated plant-available N in ASS, which could be used as valuable inorganic fertilizer.

A Comprehensive Overview of Tomato Processing By-Product Valorization by Conventional Methods versus Emerging Technologies

The tomato processing industry can be considered one of the most widespread food manufacturing industries all over the world, annually generating considerable quantities of residue and determining disposal issues associated not only with the wasting of invaluable resources but also with the rise of significant environmental burdens. In this regard, previous studies have widely ascertained that tomato by-products are still rich in valuable compounds, which, once recovered, could be utilized in different industrial sectors. Currently, conventional solvent extraction is the most widely used method for the recovery of these compounds from tomato pomace. Nevertheless, several well-known drawbacks derive from this process, including the use of large quantities of solvents and the difficulties of utilizing the residual biomass. To overcome these limitations, the recent advances in extraction techniques, including the modification of the process configuration and the use of complementary novel methods to modify or destroy vegetable cells, have greatly and effectively influenced the recovery of different compounds from plant matrices. This review contributes a comprehensive overview on the valorization of tomato processing by-products with a specific focus on the use of "green technologies", including high-pressure homogenization (HPH), pulsed electric fields (PEF), supercritical fluid (SFE-CO₂), ultrasounds (UAE), and microwaves (MAE), suitable to enhancing the extractability of target compounds while reducing the solvent requirement and shortening the extraction time. The effects of conventional processes and the application of green technologies are critically analyzed, and their effectiveness on the recovery of lycopene, polyphenols, cutin, pectin, oil, and proteins from tomato residues is discussed, focusing on their strengths, drawbacks, and critical factors that contribute to maximizing the extraction yields of the target compounds. Moreover, to follow the "near zero discharge concept", the utilization of a cascade approach to recover different valuable compounds and the exploitation of the residual biomass for biogas generation are also pointed out.

Biochar application for greenhouse gas mitigation, contaminants immobilization and soil fertility enhancement: A state-of-the-art review

Rising global temperature, pollution load, and energy crises are serious problems, recently facing the world. Scientists around the world are ambitious to find eco-friendly and cost-effective routes for resolving these problems. Biochar has emerged as an agent for environmental remediation and has proven to be the effective sorbent to inorganic and organic pollutants in water and soil. Endowed with unique attributes such as porous structure, larger specific surface area (SSA), abundant surface functional groups, better cation exchange capacity (CEC), strong adsorption capacity, high environmental stability, embedded minerals, and micronutrients, biochar is presented as a promising material for environmental management, reduction in greenhouse gases (GHGs) emissions, soil management, and soil fertility enhancement. Therefore, the current review covers the influence of key factors (pyrolysis temperature, retention time, gas flow rate, and reactor design) on the production yield and property of biochar. Furthermore, this review emphasizes the diverse application of biochar such as waste management, construction material, adsorptive removal of petroleum and oil from aqueous media, immobilization of contaminants, carbon sequestration, and their role in climate change mitigation, soil conditioner, along with opportunities and challenges. Finally, this review discusses the evaluation of biochar standardization by different international agencies and their economic perspective.

Using Alternative Sources of Energy for Decarbonization: A Piece of Cake, but How to Cook This Cake?

Few analytical or research works claim that the negative impact of improper use of ASEs may be comparable with that of hydrocarbons and sometimes even greater. It has become a common view that "green" energy (ASE) is clean, safe and environmentally friendly (eco-friendly) in contrast with "black" energy (hydrocarbons). We analyzed 144 works on systemic and/or comparative research of the modern and prospective ASE: biofuels, hydrogen, hydropower, nuclear power, wind power, solar power, geothermal power, oceanic thermal power, tidal power, wind wave power and nuclear fusion power. We performed our analysis within the Spaceship Earth paradigm. We conclude that there is no perfect ASE that is always eco-friendly. All ASEs may be dangerous to the planet considered as a closed and isolated unit ("spaceship") if they are used in an inconsistent manner. This is not in the least a reason to deny them as prospective sources of energy. Using all ASEs in different proportions in various regions of the planet, where their harm to the planet and humanity can be minimized and, on the contrary, their efficiency maximized, would give humanity the opportunity to decarbonize the Earth, and make the energy transition in the most effective way.

Recent advances in biogas production using Agro-Industrial Waste: A comprehensive review outlook of Techno-Economic analysis

Agrowaste sources can be utilized to produce biogas by anaerobic digestion reaction. Fossil fuels have damaged the environment, while the biogas rectifies the issues related to the environment and climate change problems. Techno-economic analysis of biogas production is followed by nutrient recycling, reducing the greenhouse gas level, biorefinery purpose, and global warming effect. In addition, biogas production is mediated by different metabolic reactions, the usage of different microorganisms, purification process, upgrading process and removal of CO₂ from the gas mixture techniques. This review focuses on pre-treatment, usage of waste, production methods and application besides summarizing recent advancements in biogas production. Economical, technical, environmental properties and factors affecting biogas production as well as the future perspective of bioenergy are highlighted in the review. Among all agro-industrial wastes, sugarcane straw produced 94% of the biogas. In the future, to overcome all the problems related to biogas production and modify the production process.

Valorisation Potential of Invasive Acacia dealbata, A. longifolia and A. melanoxylon from Land Clearings

Acacia spp. are invasive in Southern Europe, and their high propagation rates produce excessive biomass, exacerbating wildfire risk. However, lignocellulosic biomass from Acacia spp. may be utilised for diverse biorefinery applications. In this study, attenuated total reflectance Fourier transform infrared spectroscopy (FTIR-ATR), high-performance anion-exchange chromatography pulsed amperometric detection (HPAEC-PAD) and lignin content determinations were used for a comparative compositional characterisation of A. dealbata, A. longifolia and A. melanoxylon. Additionally, biomass was treated with three white-rot fungi species (Ganoderma lucidum, Pleurotus ostreatus and Trametes versicolor), which preferentially degrade lignin. Our results showed that the pre-treatments do not significantly alter neutral sugar composition while reducing lignin content. Sugar release from enzymatic saccharification was enhanced, in some cases possibly due to a synergy between white-rot fungi and mild alkali pretreatments. For example, in A. dealbata stems treated with alkali and P. ostreatus, saccharification yield was 702.3 nmol mg^-1, which is higher than the samples treated only with alkali (608.1 nmol mg^-1), and 2.9-fold higher than the non-pretreated controls (243.9 nmol mg^-1). By characterising biomass and pretreatments, generated data creates value for unused biomass resources, contributing to the implementation of sustainable biorefining systems. In due course, the generated value will lead to economic incentives for landowners to cut back invasive Acacia spp. more frequently, thus reducing excess biomass, which exacerbates wildfire risk.

Hydrothermal oxygen uncoupling of high-concentration biogas slurry over Cu-α-Fe2O3·α-MoO3 catalyst

A hydrothermal oxygen uncoupling (HTOU) method which combines aqueous phase reforming (APR) and oxygen uncoupling was proposed to treat biogas slurry (BS). Based on Le Chatelier's principle, this novel approach was constructed and realized by Cu-α-Fe₂O₃·α-MoO₃ catalyst with van der Waals heterojunction-redox property. Additionally, the catalyst was synthesized by integrating a simple one-pot sol-gel method and thermal hydrogenating. Results indicated that the optimal removal efficiencies of non-purgeable organic carbon (NPOC) (76.29%), total nitrogen (TN) (45.56%), and ammonia nitrogen (AN) (29.03%) were achieved on the Cu-α-Fe₂O₃·α-MoO₃ catalyst at 225.00 °C for 30.00 min, respectively. The significant performance of Cu-α-Fe₂O₃·α-MoO₃ could be attributed to three aspects. (1) The α-MoO₃ nanosheets with van der Waals heterostructures obtained at the calcination temperature of 600.00 °C, which can provide the superior performance of APR for hydrogen generation. (2) The adsorbed oxygen species were eliminated by thermal hydrogenating which had a surface passivation effect. (3) The effect of oxygen uncoupling in the lattice oxygen and gaseous oxygen release reaction was beneficial to the degradation of organic matter. Moreover, the reuse of catalysts studies further revealed that the deactivation of catalysts originated from carbon deposition of aromatic polymers and heavy metals oxides pollution. Overall, these findings disclosed that the HTOU could be a promising alternative to the treatment of high-concentration organic wastewater.

Effect of optimized intermittent mixing during high-solids anaerobic co-digestion of food waste and sewage sludge: Simulation, performance, and mechanisms

Inadequate mixing has been proven to be a major cause of anaerobic digester failure. This study revealed the mechanism of mixing intervals on high-solids anaerobic co-digestion (HS-AcoD) of food waste (FW) and sewage sludge (SS). Optimized intermittent mixing time (15 min/h) was determined through computational fluid dynamics (CFD) simulation. Experimental results indicated that the simulated intermittent mixing could shorten digestion time and increase cumulative methane output (366.8 mL/gVS) compared with continuous mixing and unmixing. Mixing could considerably accelerate substrate solubilization and hydrolysis. Maximum rates of acidogenesis (53.35 %) and methanogenesis (49.41 %) were observed with an optimized intermittent mixing (15 min/h). Vigorous mixing induced apoptosis and disrupted syntrophic metabolism, whereas intermittent mixing promoted the syntrophic metabolism between Syntrophomonas and Methanobacterium, and led to an enrichment of genes involved in acidogenic and methanogenic pathways. These findings have important implications for the development of an optimized intermittent mixing strategy for maximizing HS-AcoD efficiency of FW and SS.

Sewage sludge treatment technology under the requirement of carbon neutrality: Recent progress and perspectives

In the context of climate policies that advocate carbon neutrality, carbon emission reduction provides a new restriction in evaluating the waste activated sludge (WAS) treatment technologies and procedures. This review provides an overview of current researches and development efforts in WAS treatment, focusing on the dual attributes of WAS as contaminants and resources. Firstly, the improved technical requirements posed by heavy metals, micro(nano) plastics, or other emerging plastics in WAS are studied. Furthermore, in terms of carbon emission reduction, the applications and limitations of widely deployed WAS treatment technologies are discussed. Based on carbon neutrality requirements, the anaerobic co-digestion and co-pyrolysis technologies are comprehensively discussed from the views of pollutants removing efficiencies, enhancement methods, carbon emissions, and resource recovery. Finally, a workable new route for WAS treatment is proposed for future technological advancement and engineering innovation.

Potato peel waste for fermentative biohydrogen production using different pretreated culture

How to manage potato peel waste sustainably has been an issue faced by the potato industry. This work explored the feasibility of potato peel waste for biohydrogen production via dark fermentation, and investigated the effects of various inoculum enrichment methods (acid, aeration, heat-shock and base) on the process efficiency. It was observed that the hydrogen production showed a great variation when using various inoculum enrichment methods, and the aeration enriched inoculum obtained the maximum hydrogen yield of 71.0 mL/g-VS_added and VS removal of 28.9 %. Different enriched cultures also exhibited huge variations in the bacterial community structure and metabolic pathway. The highest abundance of Clostridium sensu stricto fundamentally contributed to the highest process efficiency for the fermenter inoculated with aeration treated culture. This work puts forward a promising strategy for recycling potato peel waste, and fills a gap in the optimal inoculum preparation method for biohydrogen fermentation of potato peel waste.

Alleviating "inhibited steady-state" in anaerobic digestion of poultry manure by bentonite amendment: Performance evaluation and microbial mechanism

This study systematically evaluated the effects of bentonite as a possible additive to alleviate the "inhibited steady-state" induced by ammonia and acid accumulation during anaerobic digestion. Continuous stirred tank reactors fed with poultry manure were operated at 35 ± 1 °C either with bentonite or not. The results demonstrate that bentonite amendment increased average specific methane production by 35% as suffered from steady-state at an organic loading rate of 6.25 g VS/L·d. 16S rRNA gene amplicon sequencing revealed that the relative abundance of electron-donating Sedimentibacter and Syntrophomonas, and electrophilic Methanosarcina was increased by 110%, 91%, and 49%, respectively. The genera were identified as crucial for alleviating "inhibited steady-state", through establishment of a more robust syntrophic pathway of methanogenic acetate degradation. The enhancement might result from the accelerated electron transfer by bentonite, which is qualified for serving as an exogenetic electron mediator due to containing abundant redox-active metal elements.

Efficient removal of tar employing dolomite catalyst in gasification: Challenges and opportunities

Fossil fuels are currently the dominant source of electricity and energy production around the world. Biomass is one of the most referred renewable carbonaceous resource(s) that can be employed for the waste-to-energy concept. Syngas obtained from biomass gasification can be utilized for a variety of key industrial purposes, including internal gasification engine operation, power generation, and hydrocarbon compound production using the Fisher-Tropsch technique. However, the existence of impurities such as hydrogen sulfide, tar, and particulate matter along with other undesirable chemicals present in syngas are major disadvantages of biomass gasification. Tar is the most difficult among all the pollutants to be removed from syngas; it also causes serious problems in downstream syngas applications. For decades, studies have been performed with various catalysts to remove the tar. Dolomite has shown positive response for tar elimination and hydrogen-enriched gas production. Several studies have been carried out on dolomite for eliminating the tar from syngas. This review encompasses sources of solid waste, the mechanism of catalysis, and in-situ and ex-situ usage of dolomite in the gasification process. It addresses the key issues such as fragmentation and attrition, elutriation, and coke formation along with dolomite's usefulness in amalgamation with other catalysts, environmental consequences, and economic viability of dolomite applications. It also discusses the challenges and opportunities for tar removal using catalysts, with a specific focus on dolomite along with economic and environmental sustainability considerations.

Producing insect protein from food waste digestate via black soldier fly larvae cultivation: A promising choice for digestate disposal

The treatment of food waste digestate with high salinity is a big challenge. This paper evaluated the possibility of using black soldier fly larvae for food waste digestate disposal and insect protein production. Results showed that both digestates from hydrogen and methane fermentations were rich in protein and lipid contents, which benefited the BSFL cultivation. The BSFL reared on digestates from hydrogen and methane fermentations of food waste performed better in pre-pupal weight (19.12% and 41.13% higher, respectively), body length (3.62% and 18.21% higher, respectively) and crude protein contents (7.85% and 39.05% higher, respectively) than that reared on raw food waste. In addition, the maximum body weight growth rate (R_m) of BSFL cultivated on both digestates were 28.28% and 47.10% higher than that of BSFL cultivated on raw food waste, respectively. During BSFL cultivation, organic matter reduction between 40.97% and 46.07% were achieved. Digestates from hydrogen and methane fermentations represent favorable feeding substrates for BSFL cultivation. Using BSFL to treat AD digestate not only provides a digestate disposal approach, but also produces insect biomass and organic fertilizer as value-added byproducts, which shows tremendous potential in digestate disposal.

Application of autothermal thermophilic aerobic digestion as a sustainable recycling process of organic liquid waste: Recent advances and prospects

Autothermal thermophilic aerobic digestion (ATAD) has been used to stabilize organic waste since the 1960s and is considered sustainable technology. ATAD has several advantages, including high biodegradation efficiency, pathogen inactivation, and ease of operation. Although ATAD research has a long history, the number of studies on ATAD is much lower than those on similar aerobic processes, particularly composting. Previous review articles addressed the origin, design, operational experiences, metabolism, and the microorganisms at the thermophilic stage of ATAD. This article reviews the digestion systems, applications, and characteristics of ATAD; compares system performance and microbial community structure of ATAD with those of other biological processes such as composting, activated sludge, and anaerobic digestion; and discusses the physicochemical properties and factors of ATAD. The challenges, opportunities, and prospects for the application of ATAD are also discussed. This review suggests that ATAD is feasible for treating organic liquid waste (1-6% total solid content) in small-sized towns and can help establish a sustainable society.

Enhanced biogas production from food waste and activated sludge using advanced techniques - A review

Biogas generation using food waste anaerobic co-digestion with activated sludge provides a cleaner addressable system, an excellent solution to global challenges, the increasing energy demands, fuel charges, pollution and wastewater treatment. Regardless of the anaerobic digestate end product values, the technology lacks efficiency and process instability due to substrate irregularities. Process parameters and substrate composition, play a vital role in the efficiency and outcome of the system. Intrinsic biochar properties such as pore size, specific surface properties and cation exchange capacity make it an ideal additive that enriches microbial functions and enhances anaerobic digestion. The pretreatment and co-digestion of food waste and activated sludge are found to be significant for efficient biogas generation. The advantages, drawbacks, limitations, and technical improvements are covered extensively in the present review besides the recent advancement in the anaerobic digestion system.

Sustainable management of municipal solid waste through waste-to-energy technologies

Increasing municipal solid waste (MSW) generation and environmental concerns have sparked global interest in waste valorization through various waste-to-energy (WtE) to generate renewable energy sources and reduce dependency on fossil-derived fuels and chemicals. These technologies are vital for implementing the envisioned global "bioeconomy" through biorefineries. In light of that, a detailed overview of WtE technologies with their benefits and drawbacks is provided in this paper. Additionally, the biorefinery concept for waste management and sustainable energy generation is discussed. The identification of appropriate WtE technology for energy recovery continues to be a significant challenge. So, in order to effectively apply WtE technologies in the burgeoning bioeconomy, this review provides a comprehensive overview of the existing scenario for sustainable MSW management along with the bottlenecks and perspectives.

Assessment of hydrogen production from municipal solid wastes as competitive route to produce low-carbon H2

An economic and CO₂ emission impact assessment of the production of H₂ from municipal solid waste in the two configurations of retrofitting an existing waste to energy plant with an electrolysis unit (WtE + El) and of hydrogen production via waste gasification (WtH₂) is made with respect to reference cases of H₂ production by steam reforming of methane (SMR) or of water electrolysis (El). The results are analyzed with reference to two scenarios depending on whether the fate of waste disposal emissions for SMR and El is accounted. The costs of H₂ production as a function of waste gate fee and CO₂ taxation as well as the CO₂ emissions for both scenarios and the four cases of H₂ production analyzed are reported. The results show that produce H₂ from a WtE plant hybridized with an electrolyzer could be economic only when the plant is free from depreciation costs and no CO₂ taxation exists. Conversely, WtH₂ solution results preferable when CO₂ taxation will be applied to the non-biogenic fraction of waste. Conditions when WtH₂ may results competitive to SMR are defined, in terms of both cost of production and CO₂ emissions. With respect to El case, WtH₂ results more competitive under the assumption made in terms of combined costs and CO₂ emissions.

Biochar and hydrochar in the context of anaerobic digestion for a circular approach: An overview

Biochar and hydrochar are carbonaceous materials with valuable applications. They can be synthesized from a wide range of organic wastes, including digestate. Digestate is the byproduct of anaerobic digestion (AD), which is performed for bioenergy (biogas) production from organic residues. Through a thermochemical process, such as pyrolysis, gasification, and hydrothermal carbonization - HTC, digestate can be converted into biochar or hydrochar. The addition of either biochar or hydrochar in AD has been reported to improve biochemical reactions and microbial growth, increasing the buffer capacity, and facilitating direct interspecies electrons transfer (DIET), resulting in higher methane (CH₄) yields. Both biochar and hydrochar can adsorb undesired compounds present in biogas, such as carbon dioxide (CO₂), hydrogen sulfide (H₂S), ammonia (NH₃), and even siloxanes. However, an integrated understanding of biochar and hydrochar produced from digestate through their return to the AD process, as additives or as adsorbents for biogas purification, is yet to be attained to close the material flow loop in a circular economy model. Therefore, this overview aimed at addressing the integration of biochar and hydrochar production from digestate, their utilization as additives and effects on AD, and their potential to adsorb biogas contaminants. This integration is supported by life cycle assessment (LCA) studies, showing positive results when combining AD and the aforementioned thermochemical processes, although more LCA is still necessary. Techno-economic assessment (TEA) studies of the processes considered are also presented, and despite an expanding market of biochar and hydrochar, further TEA is required to verify the profitability of the proposed integration, given the specificities of each process design. Overall, the synthesis of biochar and hydrochar from digestate can contribute to improving the AD process, establishing a cyclic process that is in agreement with the circular economy concept.

Addressing the water-energy nexus: A focus on the barriers and potentials of harnessing wastewater treatment processes for biogas production in Sub Saharan Africa

Several anthropogenic activities reduce the supply of freshwater to living organisms in all ecological systems, particularly the human population. Organic matter in derived wastewater can be converted into potential energy, such as biogas (methane), through microbial transformation during anaerobic digestion (AD). To address the current lack of data and values for wastewater generation in Sub-Saharan Africa, this review analyzes and estimates (at 50% and 90% conversion rates) the potential amount of wastewater-related sludge that can be generated from domestic freshwater withdrawals using the most recent update in 2017 from the World Bank repository and database on freshwater status in Sub-Saharan Africa. The Democratic Republic of the Congo (DRC) could potentially produce the highest estimate of biogas in Sub-Saharan Africa from domestic wastewater sludge of approximately 90 billion m3, which could be converted to 178 million MWh of electricity annually, based on this extrapolation at 50% conversion rates. Using same conversion rates estimates, at least nine other countries, including Guinea, Liberia, Nigeria, Sierra Leone, Angola, Cameroon, Central African Republic, Gabon, and Congo Republic, could potentially produce biogas in the range of 1-20 billion m3. These estimates show how much energy could be extracted from wastewater treatment plants in Sub-Saharan Africa. AD process to produce biogas and energy harvesting are essential supplementary operations for Sub-Saharan African wastewater treatment plants. This approach could potentially solve the problem of data scarcity because these values for Freshwater withdrawals are readily available in the database could be used for estimation and projections towards infrastructure development and energy production planning. The review also highlights the possibilities for energy generation from wastewater treatment facilities towards wastewater management, clean energy, water, and sanitation sustainability, demonstrating the interconnections and actualization of the various related UN Sustainable Development Goals.

Co-application of biochar and organic fertilizer promotes the yield and quality of red pitaya (Hylocereus polyrhizus) by improving soil properties

This study evaluated the combined impact of biochar and organic fertilizer on the soil properties, yield and quality of red pitaya (Hylocereus polyrhizus). A two-year (2019 and 2020) field experiment was conducted to study the effects of 3 rates of biochar (with carbon fertilizer ratios of 0%, 3%, and 6% w/w) combined with 3 levels of organic fertilizer (22.5, 45, and 90 t ha^-1) on soil properties, along with red pitaya yield and quality. The results showed that soil pH, total organic carbon, available nutrients (N, P, and K), the yield and qualities (reduced sugar, soluble protein, and soluble solid) of red pitaya increased with the application of organic fertilizer compared with no application of biochar and organic fertilizer (CK treatment), but the combined application of biochar and organic fertilizer was more effective than their sole application. Furthermore, a medium dose of organic fertilizer combined with 3% biochar (C3F2 treatment) and a high dose of organic fertilizer combined with 3% biochar (C3F3 treatment) had the highest yields of red pitaya in 2019 and 2020. However, an application of 6% biochar with a low dose of organic fertilizer treatment (C6F1) had the highest profit in 2020, not the C3F3 treatment. The highest profits were observed in the C3F2 (71.0 × 10³ RMB·t^-1) and C6F1 (51.2 × 10³ RMB·t^-1) treatments. From the point of view of red pitaya yield and economic benefits, 3% biochar +45 t ha^-1 organic fertilizer was the recommended combination that showed the best synergistic effect.

Effects of biochar on water quality and rice productivity under straw returning condition in a rice-wheat rotation region

Straw returning is helpful to improve soil properties and realize the reutilization of agricultural waste. However, wheat straw returning may result in paddy water quality deterioration in rice-wheat rotation regions. This study conducted pot experiments of rice planting with different biochar application rates (0, 5, 20, and 40 t/hm²) under wheat straw returning conditions. The purposes are to investigate the applicability of biochar mixed with wheat straw returning to paddy fields and explore the effects of biochar on water quality, leaching losses of nitrogen (N) and phosphorus (P), and rice yield components. Results indicated that total straw returning reduced the water quality in paddy surface water and aggravated the leaching losses of N and P. Fortunately, the biochar application improved the negative effects caused by straw returning. 40 t/hm² biochar mixed with straw returning significantly reduced the concentrations of COD and N in paddy surface water and N leaching loss than straw returning treatment (ST), decreased by 48.33%, 41.01%, and 45.73%, respectively. Meanwhile, applying biochar at a rate of 20 t/hm² with straw returning is suitable to control the diffusion of P. In addition, the ST treatment had no significant effect on rice yield, while the proper application rate of biochar under straw returning condition can improve rice yield and promote N utilization. 20 t/hm² biochar treatment is more effective to improving rice yield (16.89%) and N use efficiency (NUE) (10.14%). These findings can provide a new method to solve the negative effects of total straw returning on the water environment and rice growth and guide the utilization of straw resources in the rice-wheat rotation regions.

Impacts of gasification biochar and its particle size on the thermal behavior of organic waste co-composting process

This work investigates the effects of gasification biochar on the thermal behavior of organic municipal waste composting. Two different biochar granulometries were mixed in a 3% w/w share with the organic fraction of municipal waste and tested in nine (three per thesis and three as control) reactors of 1 m³ of volume, designed to simulate full-scale aerated static piles. The temperatures of each composter were monitored for 31 days of the active composting phase and used as key parameters for air flow tuning. After the active phase was completed, the air was turned off and the temperatures were monitored for an additional 31 days during compost maturation. Results show that biochar-aided composters run 4 °C hotter and are more stable in temperature compared to the control thesis. Experimental data were used as a basis for thermal energy modeling: the addition of fine biochar to composting material increased the thermal energy production by 0.5 MJ kg^-1 compared to the control thesis; coarse biochar increased the thermal energy production by 0.4 MJ kg^-1. The standard composting process, without biochar, produced 2.5 MJ kg^-1. Results might serve as a starting point for further considerations in terms of composting time reduction, improvement of the final product and reduction of process related issues, such as undesired anaerobic decomposition, leachate production and temperature instability.

Wastewater in the food industry: Treatment technologies and reuse potential

Water is the most extensively used raw material in the food and beverage industry. This industrial sector has a negative impact on the environment and economy as a result of rising water demand and wastewater production. With the increasing scarcity of drinking water, the reuse of wastewater streams has become an important economic and ecological concern. Therefore, the optimisation of water consumption and wastewater reuse in the food industry is essential. On the other hand, several countries limit the reuse of wastewater because of legal curtailment, public health and safety concerns. This represents a major challenge for both industries and administrations due to the technical complexity and financial costs involved. The present review aims at addressing the key issues related to water consumption, wastewater generation, treatment and successful implementation cases of water reuse in the food and beverage industry. Moreover, the various case studies of already employed technologies for the food industry wastewater treatment and reuse have been analysed for their performance. Also, this review reveals future research on the application of other innovative technologies such as ultraviolet irradiation and micro electrolysis. However, the successful implementation of reuse strategies is associated with the holistic evaluation of local factors such as governmental incentives, social acceptance and legislation harmonisation related to the cost, risks, and environmental performance.

Multifunctional applications of bamboo crop beyond environmental management: an Indian prospective

Increasing population, industrialization, and economic growth cause several adverse impacts on the existing environment and living being. Therefore, rising pollutants load and their mitigation strategies, as well as achieving energy requirements while reducing reliance on fossil fuels are the key areas, which needs significant consideration for sustainable environment. Since India has considerable biomass resources, bioenergy is a significant part of the country’s energy policy. However, the selection of feedstock is a crucial step in bioenergy production that could produce raw material without compromising food reserve along with the sustainable environment. Higher growth capacity of bamboo species makes them a suitable lignocellulosic substrate for the production of high-value greener products such as fuels, chemicals, and biomaterials as well as an appropriate candidate for eco-restoration of degraded land. In that context, the current review discusses the multidimensional applications of bamboo species in India. The bioenergy potency of bamboo and probability of aligning its production, cultivation, and operation with economic and social development agendas are also addressed, making it an exceptional crop in India. Additionally, its fast growth, perennial root systems, and capability to restore degraded land make it an essential part of ecological restoration. Furthermore, this review explores additional benefits of bamboo plantation on the environment, economy, and society along with future research prospects.

Study on personalized microbial formulation during high-temperature aerobic fermentation of different types of food wastes

The rapidly growing generation of food wastes has attracted extensive attention. In this context, biochemical processors, using high-temperature aerobic fermentation, has become a beneficial method to treat food waste in situ. However, existing microbial agents do not vary the proportion of strains according to the different food wastes, with this approach affecting the degradation efficiency. In this study, high-temperature resistant strains, with high degradation efficiency, were isolated and screened, before establishing a novel method for preparing personalized microbial formulations. Using the degradation efficiency of wastes after three days as the evaluation standard, 12 groups of Plackett-Burman experiments were used to determine the main effect strains for different types of food waste. Fifteen groups of Box-Behnken experiments were then used to determine their best proportions at which the maximum degradation efficiency occurred. Finally, simulated fermentation experiments were used to check for improvement of the fermentation process by mixing strains according to the personalized proportions. Results of molecular identification and physiological assessments indicated that all the seven strains were Bacillus spp., with no antagonistic effects between them. Based on the Plackett-Burman and Box-Behnken tests, three personalized bacterial agents were obtained for different types of food waste. The fermentation results further showed that, compared with the use of equal proportions of strains, a maximum increase of 15.43% in organic matter degradation was achieved after adding personalized proportions. This study provides both theoretical and practical references for the use of personalized microbial agent formulations for high-temperature aerobic fermentation of food wastes, thus providing these microbial agents with good prospects and economic value.

Effect of biochar addition on the dynamics of antibiotic resistant bacteria during the pig manure composting

In present study, the taxonomic variation of antibiotic resistant bacteria (ARB) in pig manure (PM) composting with coconut shell biochar (CSB) and bamboo biochar (BB) addition was investigated. The experiment was divided into three treatments: T1 (as control or without biochar amendment), T2 was added 10% coconut shell biochar and T3 supplemented with 10% bamboo biochar. The initial feed stock were properly homogenized using a mechanical crusher. PM and wheat straw (WS) were mixed in a 5: 1 dry weight ratio to adjust the initial carbon/nitrogen ratio 25:1, bulk density to ~0.5 (kg/L) and ~60% moisture content, respectively. This experiment was lasted for 42 days. The results indicated the bacterial communities in the three treatments were more different in terms of relative abundance and diversity of dominant bacteria. The control group had the highest abundance of Kingdome bacteria. The changes in ARB was noticed by variation in the relative abundances of Actinobacteria, Proteobacteria, Firmicutes and Bacteroidota. At the end of composting (on day 42), the total RAs of ARB at the class, order, and family levels were considerably reduced in T2 and T3 by ~35.78-38.75%, 36.42-40.63% and 45.82-47.70%, respectively. But in T1 was decreased by 6.16-8.62%, 7.93-8.72% and 8.70-10.15%, as compared with the day 0 sample. However, the CSB was much more effective to reduce 55 to 60% of ARB than T3 or BB applied treatment has 40 to 42% ARB reduction, while control has certainly very less RAa of ARB reduction. Finally, the biochar amendment was significant approach to mitigate the total ARB abundance in compost and it's further used for organic farming purposes.

Effects of digestion duration on energy efficiency, compost quality, and carbon flow during solid state anaerobic digestion and composting hybrid process

This study investigated the effects of anaerobic digestion duration on methane yield, net energy production, and humification of compost during solid state anaerobic digestion (SSAD) and composting hybrid process for food waste treatment. Carbon flow and balance were used to evaluate organic methanation and humification inclination of carbon in the whole SSAD and aerobic composting system. Results showed that SSAD for 15 (AD-15) and 21 days (AD-21) could increase net energy production and degraded organic matter contained in the mixtures to achieve high biological stability. The cumulative net energy production between the AD-15 and AD-21 treatments was not significantly different, which was 8.3% higher than that in SSAD for 30 days (AD-30). Furthermore, digestate (AD-15 and AD-21) composting for 3 days reached maturity and absence of phytotoxic substances. Carbon fixed into humus of the AD-21 treatment (11.6%) was not significantly different from that of AD-15 (12.0%). However, the total amount of carbon fixed into compost in AD-15 was 6.6% higher than that in AD-21. Moreover, the CO₂ -C loss of the AD-15 treatment (22.9%) was slightly higher than that of AD-21 (20.6%). Thus, AD-21 treatment achieved the most effective use of carbon during SSAD and composting hybrid process for food waste treatment. These results could provide valuable insights for the effective management of food waste in practice.

Economic and environmental sustainability analysis of seaweed farming: Monetizing carbon offsets of a brown algae cultivation system in Ireland

This paper examines the economic and environmental costs of seaweed cultivation (Alaria esculenta) in Ireland and evaluates the potential revenue made on the voluntary carbon offset market (VCOM). The life cycle assessment (LCA) results revealed the cultivation equipment with the polypropylene used for the cultivation lines contributes the highest share of impacts due to their replacement rate. This study suggests long-term employment of farm infrastructure and increased seaweed yield could enhance the environmental sustainability of the system. Moreover, life cycle costing (LCC) indicates the seaweed farm in Ireland is economically feasible over a 20-year lifespan. However, the revenue generated on the VCOM from the seaweed carbon assimilation was minimal, contributing to only 5% of the revenue. This study concludes that further development of the seaweed market with stabilized biomass prices and producing a range of viable products from seaweed biomass will be a major factor in the economic sustainability.

Responses of methane production, microbial community and antibiotic resistance genes to the mixing ratio of gentamicin mycelial residues and wheat straw in anaerobic co-digestion process

Anaerobic co-digestion (AcoD) of gentamicin mycelial residues (GMRs), a kind of nitrogen-rich biowaste, and wheat straw (WS) is an attractive technology for the recycling of GMRs. However, the effects of the co-substrate ratio on methane production, system stability and antimicrobial resistance during co-digestion remain unclear. Thus, this study aimed to fill in the blanks through AcoD of GMRs and WS with different mixing ratios (1:0, 2:1, 1:1, 1:2, 0:1, VS basis) via batch tests. Results showed that AcoD facilitated methane production than mono anaerobic digestion and reduced the accumulation of the toxic substances, such as ammonia nitrogen and humic-like substances. The maximum methane production was obtained at the reactors with the mixing ratio of 1:1 and 1:2 (R-1:1 and R-1:2), which matched with the relative abundance of key enzymes related to methanogenesis predicted by PICRUSt. Microbial community analysis indicated that Methanosaeta was the most dominant methanogen in the AcoD reactors. The highest relative abundance of Methanosaeta (45.1%) was obtained at R-1:1 due to the appropriate AcoD conditions, thus, providing greater possibilities for high stability of AcoD system. Additionally, AcoD of the GMRs and WS under the mixing ratio of 1:1 and 1:2 did not prompt the increase of antibiotic resistance genes (ARGs). Not only that, the likelihood of horizontal gene transfer declined in R-1:1 due to the weaker connection and transport between host and recipient bacteria. Findings of this study suggested that the suitable mixing ratio of GMRs and WS contributes to methane production and system stability, and reduces the dissemination risks of ARGs.