Hall effect biosensors with ultraclean graphene film for improved sensitivity of label-free DNA detection

A novel electrochemical aptasensor based on eco-friendly synthesized titanium dioxide nanosheets and polyethyleneimine grafted reduced graphene oxide for ultrasensitive and selective detection of ciprofloxacin

Developing a rapid, sensitive, and efficient analytical method for the trace-level determination of highly concerning antibiotic ciprofloxacin (CIP) is desirable to guarantee the safety of human health and ecosystems. In this work, a novel electrochemical aptasensor based on polyethyleneimine grafted reduced graphene oxide and titanium dioxide (rGO/PEI/TiO2) nanocomposite was constructed for ultrasensitive and selective detection of CIP. Through the in-situ electrochemical oxidation of Ti3C2Tx nanosheets, TiO2 nanosheets with good electrochemical response were prepared in a more convenient and eco-friendly method. The prepared TiO2 nanosheets promote charge transferring on electrode interface, and [Fe(CN)6]3-/4- as electrochemical active substance can be electrostatically attracted by rGO/PEI. Thus, electrochemical detection signal of the aptasensor variates a lot after specific binding with CIP, achieving working dynamic range of 0.003-10.0 μmol L-1, low detection limit down to 0.7 nmol L-1 (S/N = 3) and selectivity towards other antibiotics. Additionally, the aptasensor exhibited good agreement with HPLC method at 95% confidence level, and achieved good recoveries (96.8-106.3%) in real water samples, demonstrating its suitable applicability of trace detection of CIP in aquatic environment.

Recent progress on rapid diagnosis of COVID-19 by point-of-care testing platforms

The outbreak of COVID-19 has drawn great attention around the world. SARS-CoV-2 is a highly infectious virus with occult transmission by many mutations and a long incubation period. In particular, the emergence of asymptomatic infections has made the epidemic even more severe. Therefore, early diagnosis and timely management of suspected cases are essential measures to control the spread of the virus. Developing simple, portable, and accurate diagnostic techniques for SARS-CoV-2 is the key to epidemic prevention. The advantages of point-of-care testing technology make it play an increasingly important role in viral detection and screening. This review summarizes the point-of-care testing platforms developed by nucleic acid detection, immunological detection, and nanomaterial-based biosensors detection. Furthermore, this paper provides a prospect for designing future highly accurate, cheap, and convenient SARS-CoV-2 diagnostic technology.

Review on two-dimensional material-based field-effect transistor biosensors: accomplishments, mechanisms, and perspectives

Field-effect transistor (FET) is regarded as the most promising candidate for the next-generation biosensor, benefiting from the advantages of label-free, easy operation, low cost, easy integration, and direct detection of biomarkers in liquid environments. With the burgeoning advances in nanotechnology and biotechnology, researchers are trying to improve the sensitivity of FET biosensors and broaden their application scenarios from multiple strategies. In order to enable researchers to understand and apply FET biosensors deeply, focusing on the multidisciplinary technical details, the iteration and evolution of FET biosensors are reviewed from exploring the sensing mechanism in detecting biomolecules (research direction 1), the response signal type (research direction 2), the sensing performance optimization (research direction 3), and the integration strategy (research direction 4). Aiming at each research direction, forward perspectives and dialectical evaluations are summarized to enlighten rewarding investigations.

Highly Sensitive and Selective Dopamine Determination in Real Samples Using Au Nanoparticles Decorated Marimo-like Graphene Microbead-Based Electrochemical Sensors

A sensitive and selective electrochemical dopamine (DA) sensor has been developed using gold nanoparticles decorated marimo-like graphene (Au NP/MG) as a modifier of the glassy carbon electrode (GCE). Marimo-like graphene (MG) was prepared by partial exfoliation on the mesocarbon microbeads (MCMB) through molten KOH intercalation. Characterization via transmission electron microscopy confirmed that the surface of MG is composed of multi-layer graphene nanowalls. The graphene nanowalls structure of MG provided abundant surface area and electroactive sites. Electrochemical properties of Au NP/MG/GCE electrode were investigated by cyclic voltammetry and differential pulse voltammetry techniques. The electrode exhibited high electrochemical activity towards DA oxidation. The oxidation peak current increased linearly in proportion to the DA concentration in a range from 0.02 to 10 μM with a detection limit of 0.016 μM. The detection selectivity was carried out with the presence of 20 μM uric acid in goat serum real samples. This study demonstrated a promising method to fabricate DA sensor-based on MCMB derivatives as electrochemical modifiers.

One-step synthesis of nanosilver embedding laser-induced graphene for H2O2 sensor

During the novel coronavirus pandemic, hydrogen peroxide (H₂O₂) played an important role as a disinfectant. However, high concentrations of H₂O₂ can also cause damage to the skin and eyes. Therefore, the quantitative and qualitative detection of H₂O₂ is an important research direction. In this work, we report a one-step laser-induced synthesis of graphene doped with Ag NPs composites. It directly trims screen printed electrodes (SPE). Firstly, we did the timekeeping current method (CA) test on H₂O₂ using a conventional platinum sheet as the counter electrode, and obtained linear ranges of 1-110 μM and 110-800 μM with a sensitivity of 118.7 and 96.3 μAmM^-1cm^-2 and a low detection limit of (LOD) 0.24 μM and 0.31 μM. On this basis we have also achieved a good result in CA testing using Screen printed carbon electrodes (SPCE), laying the foundation for portable testing. The sensor has excellent interference immunity and high selectivity.

Innovations in the synthesis of graphene nanostructures for bio and gas sensors

Sensors play a significant role in modern technologies and devices used in industries, hospitals, healthcare, nanotechnology, astronomy, and meteorology. Sensors based upon nanostructured materials have gained special attention due to their high sensitivity, precision accuracy, and feasibility. This review discusses the fabrication of graphene-based biosensors and gas sensors, which have highly efficient performance. Significant developments in the synthesis routes to fabricate graphene-based materials with improved structural and surface properties have boosted their utilization in sensing applications. The higher surface area, better conductivity, tunable structure, and atom-thick morphology of these hybrid materials have made them highly desirable for the fabrication of flexible and stable sensors. Many publications have reported various modification approaches to improve the selectivity of these materials. In the current work, a compact and informative review focusing on the most recent developments in graphene-based biosensors and gas sensors has been designed and delivered. The research community has provided a complete critical analysis of the most robust case studies from the latest fabrication routes to the most complex challenges. Some significant ideas and solutions have been proposed to overcome the limitations regarding the field of biosensors and hazardous gas sensors.

Hermetic Packaging Based on Cu–Sn and Au–Au Dual Bonding for High-Temperature Graphene Pressure Sensor

A chip-level hermetic package for a high-temperature graphene pressure sensor was investigated. The silicon cap, chip and substrate were stacked by Cu–Sn and Au–Au bonding to enable wide-range measurements while guaranteeing a high hermetic package. Prior to bonding, the sample was treated with Ar (5% H2) plasma. The Cu–Sn bonding was firstly performed at 260 °C for 15 min with a pressure of 9.9 MPa, and the corresponding process conditions for Au–Au bonding has increased to 300 °C, 20 min and 19.8 MPa respectively. The average shearing strength was 14.3 MPa, and an excellent leak rate of 1.72 × 10−4 Pa·cm3/s was also achieved. After high-temperature storage (HTS) at 350 °C for 10 h, the resistance of graphene decreased slightly because the dual bonding provided oxygen-free environment for graphene. The leakage rate of the device slightly increased to 2.1 × 10−4 Pa·cm3/s, and the average shear strength just decreased to 13.5 MPa. Finally, under the pressure range of 0–100 MPa, the graphene pressure sensor exhibited a high average sensitivity of 3.11 Ω/MPa. In conclusion, the dual bonding that combined Cu–Sn and Au–Au is extremely suitable for hermetic packaging in high-temperature graphene pressure sensors.

DNA-Mediated Assembly of Carbon Nanomaterials

Carbon nanomaterials (CNMs) have attracted extensive attentions on account of their superior electrical, mechanical, optical, and biological properties. However, the dimensional limit and irregular arrangement have hampered their further application. It is necessary to find an easy, efficient and controllable way to assemble CNMs into well-ordered array. DNA nanotechnology, owning to the advantages of precise programmability, highly structural predictability and spatial addressability, has been widely applied in the assembly of CNMs. Summarizing the progress and achievements in this field will be of great value to related studies. Herein, based on the different dimensions of CNMs containing 0-dimensional (0D) carbon dots (CDs), fullerenes, 1-dimensional (1D) carbon nanotubes (CNTs) and 2-dimensional (2D) graphene, we introduced the conjugation strategies between DNA and CNMs, their different assembly methods and their applications. In addition, we also discuss the existing challenges and future opportunities in the field.

Detection of necrotrophic DNA marker of anthracnose causing Colletotrichum gloeosporioides fungi in harvested produce using surface plasmon resonance

Agriculture and food crops monitoring is extremely important for securing the food supply chain to human society. Here, we developed a highly specific detection method for monitoring pathogenic fungus Colletotrichum gloeosporioides using necrotrophic DNA biomarker as the recognition element and surface plasmon resonance (SPR) as transducing mechanism in the prism coupling configuration. The sensor shows its response for a wide range of concentrations from pM to μM of target DNA sequence using a complementary DNA probe immobilized on the sensor surface, which could detect concentrations as low as 7 pM. The detection limit is found to be comparable with conventional molecular-based detection platforms, achieved due to optimized spectral SPR bimetallic substrate with subpixel resolution obtained by post processing. The response time of the sensor for detection is less than 30 min at room temperature. The quick detection scheme of the sensor may facilitate the screening of a large number of samples acquired for the sorting of harvested produce. This sensor is fast, reliable, cost-effective, and can be miniaturized for portability for the screening of real samples (mRNA) in the field and packaging house.

Paper-based field-effect transistor sensors

The present scenario in the world largely demands affordable, fast, recyclable, and flexible electronic devices for bio sensing. Varieties of paper-based devices such as microfluidics paper electrodes, paper diodes, and paper-based transistors etc. have been developed and validated. Most of the fabrication techniques published so far have focused on economic, environment-friendly straightforward methods to develop paper-based field-effect transistors (PFET) sensors, additionally, explored their applications. The synthetic-free, mechanically flexible, biocompatible, and signal amplification capability render PFET based sensors for wearable device makers. Modified organic/inorganic PFETs identify target analytes based on the electrical signal and endow them as perfect transducers. In the field of PFET bio sensing technology, numerous challenges are needed to be discussed to proceed forward in biomedical and other analytical applications. Realizing biologically or chemically modified PFET having an exceptional signal to noise ratio, specificity, with rapid detection ability is challenging. This review recapitulates the fabrication techniques, performances of various PFET sensors, and summarizes the report by concluding remarks including the limitations of the existing PFET based sensors and the future holds in regards to the sustainable nature of PFET.

A Double-Deck Structure of Reduced Graphene Oxide Modified Porous Ti3C2Tx Electrode towards Ultrasensitive and Simultaneous Detection of Dopamine and Uric Acid

Considering the vital physiological functions of dopamine (DA) and uric acid (UA) and their coexistence in the biological matrix, the development of biosensing techniques for their simultaneous and sensitive detection is highly desirable for diagnostic and analytical applications. Therefore, Ti₃C₂T_x/rGO heterostructure with a double-deck layer was fabricated through electrochemical reduction. The rGO was modified on a porous Ti₃C₂T_x electrode as the biosensor for the detection of DA and UA simultaneously. Debye length was regulated by the alteration of rGO mass on the surface of the Ti₃C₂T_x electrode. Debye length decreased with respect to the rGO electrode modified with further rGO mass, indicating that fewer DA molecules were capable of surpassing the equilibrium double layer and reaching the surface of rGO to achieve the voltammetric response of DA. Thus, the proposed Ti₃C₂T_x/rGO sensor presented an excellent performance in detecting DA and UA with a wide linear range of 0.1-100 μM and 1-1000 μM and a low detection limit of 9.5 nM and 0.3 μM, respectively. Additionally, the proposed Ti₃C₂T_x/rGO electrode displayed good repeatability, selectivity, and proved to be available for real sample analysis.

Ion-Selective Membrane-Coated Graphene-Hexagonal Boron Nitride Heterostructures for Field-Effect Ion Sensing

An intrinsic ion sensitivity exceeding the Nernst-Boltzmann limit and an sp ² -hybridized carbon structure make graphene a promising channel material for realizing ion-sensitive field-effect transistors with a stable solid-liquid interface under biased conditions in buffered salt solutions. Here, we examine the performance of graphene field-effect transistors coated with ion-selective membranes as a tool to selectively detect changes in concentrations of Ca²⁺, K⁺, and Na⁺ in individual salt solutions as well as in buffered Locke's solution. Both the shift in the Dirac point and transconductance could be measured as a function of ion concentration with repeatability exceeding 99.5% and reproducibility exceeding 98% over 60 days. However, an enhancement of selectivity, by about an order magnitude or more, was observed using transconductance as the indicator when compared to Dirac voltage, which is the only factor reported to date. Fabricating a hexagonal boron nitride multilayer between graphene and oxide further increased the ion sensitivity and selectivity of transconductance. These findings incite investigating ion sensitivity of transconductance in alternative architectures as well as urge the exploration of graphene transistor arrays for biomedical applications.

Surface Modification Using Polydopamine-Coated Liquid Metal Nanocapsules for Improving Performance of Graphene Paper-Based Thermal Interface Materials

Given the thermal management problem aroused by increasing power densities of electronic components in the system, graphene-based papers have raised considerable interest for applications as thermal interface materials (TIMs) to solve interfacial heat transfer issues. Significant research efforts have focused on enhancing the through-plane thermal conductivity of graphene paper; however, for practical thermal management applications, reducing the thermal contact resistance between graphene paper and the mating surface is also a challenge to be addressed. Here, a strategy aimed at reducing the thermal contact resistance between graphene paper and the mating surface to realize enhanced heat dissipation was demonstrated. For this, graphene paper was decorated with polydopamine EGaIn nanocapsules using a facile dip-coating process. In practical TIM application, there was a decrease in the thermal contact resistance between the TIMs and mating surface after decoration (from 46 to 15 K mm2 W-1), which enabled the decorated paper to realize a 26% enhancement of cooling efficiency compared with the case without decoration. This demonstrated that this method is a promising route to enhance the heat dissipation capacity of graphene-based TIMs for practical electronic cooling applications.

Detection techniques of biological and chemical Hall sensors

Integrated magnetic Hall effect sensors have been widely used in people's daily life over the past decades, and still are gaining enormous attention from researchers to establish novel applications, especially in biochemistry and biomedical healthcare. This paper reviews, classifies, compares and concludes state-of-the-art integrated Hall magnetic sensors in terms of cost, power, area, performance and application. Current applications of the Hall sensors such as detecting magnetic nanoparticles (MNPs) labeled on biomolecule, monitoring blood pulse wave velocity, characterizing soft biological materials, controlling syringe injection rate and eye surgery by training systems, and assisting magnetic resonance imaging (MRI) will be discussed comprehensively and future applications and trends will be highlighted. This review paper will introduce Hall sensor's advantages such as simple design and technology of manufacturing, low cost, low power consumption, possibility of the miniaturizing, noninvasive and room temperature measurement, with respect to the other magnetic sensing systems and methods.

Graphene field effect transistor for ultrasensitive label-free detection of ATP and Adenosine

Because of unique electrical and structural properties, graphene has attracted widespread attention in biosensing applications. In this paper, a single layer of graphene was grown by chemical vapor deposition (CVD). Using graphene as the electric channel, a graphene field effect transistor (G-FET) biosensor was fabricated and used to detect adenosine triphosphate (ATP) and adenosine. Compared with traditional methods, the G-FET biosensor has the advantages of higher sensitivity and better stability. The sensor showed high performance and achieved a detection limit down to 0.5 pM for both ATP and adenosine. Moreover, the G-FET biosensor showed an excellent linear electrical response to ATP concentrations in a broad range from 0.5 pM to 50 μM. The developed graphene biosensor has high sensitivity, simple operation, and fast analysis speed, which may provide a new feasible direction to detect ATP and adenosine. Healthy sexually mature male laboratory Wistar rats, weighing 180-200 gr (“FSUE “Nursery of laboratory animals “Rappolovo”) and having been placed under quarantine not less than for 14 days, were selected for the experiment.

Review of fabrication methods of large-area transparent graphene electrodes for industry

Graphene is a two-dimensional material showing excellent properties for utilization in transparent electrodes; it has low sheet resistance, high optical transmission and is flexible. Whereas the most common transparent electrode material, tin-doped indium-oxide (ITO) is brittle, less transparent and expensive, which limit its compatibility in flexible electronics as well as in low-cost devices. Here we review two large-area fabrication methods for graphene based transparent electrodes for industry: liquid exfoliation and low-pressure chemical vapor deposition (CVD). We discuss the basic methodologies behind the technologies with an emphasis on optical and electrical properties of recent results. State-of-the-art methods for liquid exfoliation have as a figure of merit an electrical and optical conductivity ratio of 43.5, slightly over the minimum required for industry of 35, while CVD reaches as high as 419.

Single-Layered Graphene/Au-Nanoparticles-Based Love Wave Biosensor for Highly Sensitive and Specific Detection of Staphylococcus aureus Gene Sequences

In this work, a single-layered graphene (SLG)/Au-nanoparticles (NPs)-based Love wave biosensor was prepared for detection of Staphylococcus aureus (S. aureus) gene sequences. The annealing process was proposed to obtain a larger-area interface with ssDNA. The sensitivity was verified by detecting S. aureus gene sequences with a linear detection ranging from 0 to 10 nmol/L, where the limit of detection (LOD) was only 12.4 pg/mL. The stable state of the biosensors based on SLG/Au NPs in the liquid phase could be kept for more than 0.5 h (±0.1°), and the specificity was verified by detecting noncomplementary ssDNA and one- and three-base mismatched ssDNA. The results of our study suggest that a Love wave biosensor based on SLG/Au NPs hold great potential in clinical testing and diagnosis.

β-Cyclodextrin-Immobilized Ni/Graphene Electrode for Electrochemical Enantiorecognition of Phenylalanine

In this work, a Ni/graphene (Ni/G) electrode was designed and fabricated by plasma-enhanced chemical vapor deposition (PECVD) for the ultrasensitive recognition of d- and l-phenylalanine. Through a single-step PECVD process, the Ni/G electrode can achieve better hydrophilicity and larger catalytic surface area, which is beneficial for the electrochemical recognition of bio-objects. After surface modification with β-cyclodextrin, the Ni/G electrode can distinguish d-phenylalanine from l-phenylalanine according to a 0.09 V peak shift in differential pulse voltammetry tests. Moreover, this Ni/G electrode achieved a detection limit as low as 1 nM and a wide linear range from 1 nM to 10 mM toward l-phenylalanine, with great storage stability and working stability.

An aptamer-based shear horizontal surface acoustic wave biosensor with a CVD-grown single-layered graphene film for high-sensitivity detection of a label-free endotoxin

The thickness of the sensitive layer has an important influence on the sensitivity of a shear horizontal surface acoustic wave (SH-SAW) biosensor with a delay-line structure and lower layer numbers of graphene produce better sensitivity for biological detection. Therefore, a label-free and highly sensitive SH-SAW biosensor with chemical vapor deposition (CVD-)-grown single-layered graphene (SLG) for endotoxin detection was developed in this study. With this methodology, SH-SAW biosensors were fabricated on a 36° Y-90° X quartz substrate with a base frequency of 246.2 MHz, and an effective detection cell was fabricated using acrylic material. To increase the surface hydrophilicity, chitosan was applied to the surface of the SLG film. Additionally, the aptamer was immobilized on the surface of the SLG film by cross-linking with glutaraldehyde. Finally, the sensitivity was verified by endotoxin detection with a linear detection ranging from 0 to 100 ng/mL, and the detection limit (LOD) was as low as 3.53 ng/mL. In addition, the stability of this type of SH-SAW biosensor from the air phase to the liquid phase proved to be excellent and the specificity was tested and verified by detecting the endotoxin obtained from Escherichia coli (E. coli), the endotoxin obtained from Pseudomonas aeruginosa (P. aeruginosa), and aflatoxin. Therefore, this type of SH-SAW biosensor with a CVD-grown SLG film may offer a promising approach to endotoxin detection, and it may have great potential in clinical applications.

Graphdiyne-Based One-Step DNA Fluorescent Sensing Platform for the Detection of Mycobacterium tuberculosis and Its Drug-Resistant Genes

The accurate and early detection of Mycobacterium tuberculosis (Mtb) is of great significance for the clinical diagnosis and treatment of tuberculosis. In this work, we report a facile method for the controllable synthesis of a novel few-layered two-dimensional graphdiyne nanosheet (GDY NS) with a thickness of only ∼0.9 nm via an electrochemical lithium-intercalation strategy, which possesses a prominent fluorescence quenching effect. The few-layered GDY NS with its strong adsorptivity for single-stranded DNA is first proposed as a new fluorescent sensing platform for the real-time detection of DNA with excellent specificity, multiplicity, and superhigh sensitivity (limit of detection as low as 25 pM). This sensing platform can be further applied for the Mtb detection from clinical samples and the identification of drug-resistant mutants with a low background and a high signal-to-noise ratio. Herein, we provide a potential basis for the clinical development of rapid, sensitive, and accurate substitutes for the molecular diagnosis of Mtb and its drug-resistant genes.

Single-Step Formation of Ni Nanoparticle-Modified Graphene-Diamond Hybrid Electrodes for Electrochemical Glucose Detection

The development of accurate, reliable devices for glucose detection has drawn much attention from the scientific community over the past few years. Here, we report a single-step method to fabricate Ni nanoparticle-modified graphene–diamond hybrid electrodes via a catalytic thermal treatment, by which the graphene layers are directly grown on the diamond surface using Ni thin film as a catalyst, meanwhile, Ni nanoparticles are formed in situ on the graphene surface due to dewetting behavior. The good interface between the Ni nanoparticles and the graphene guarantees efficient charge transfer during electrochemical detection. The fabricated electrodes exhibit good glucose sensing performance with a low detection limit of 2 μM and a linear detection range between 2 μM–1 mM. In addition, this sensor shows great selectivity, suggesting potential applications for sensitive and accurate monitoring of glucose in human blood.

Recent advances in graphene-based nanomaterials: properties, toxicity and applications in chemistry, biology and medicine

This review (with 239 refs.) summarizes the progress that has been made in applications of graphene-based nanomaterials (such as plain graphene, graphene oxides, doped graphene oxides, graphene quantums dots) in biosensing, imaging, drug delivery and diagnosis. Following an introduction into the field, a first large section covers the toxicity of graphene and its derivatives (with subsections on bacterial toxicity and tissue toxicity). The use of graphene-based nanomaterials in sensors is reviewed next, with subsections on electrochemical, FET-based, fluorescent, chemiluminescent and colorimetric sensors and probes. The large field of imaging is treated next, with subchapters on optical, PET-based, and magnetic resonance based methods. A concluding section summarizes the current status, addresses current challenges, and gives an outlook on potential future trends. Graphical Abstract Schematic presentation of the potential applications of graphene-based materials in life science and biomedicine, emphatically reflected in some vital areas such as DNA analysis, biological monitoring, drug delivery, in vitro labelling, in vivo imaging, tumor target, etc.

Low-Voltage-Operated Highly Sensitive Graphene Hall Elements by Ionic Gating

The advanced Hall magnetic sensor using an ion-gated graphene field-effect transistor demonstrates a high current-normalized sensitivity larger than 3000 V/AT and low operation voltages smaller than 0.5 V. From commercially available graphene-on-SiO₂ wafers, large-area arrays of ion-gated graphene Hall element (ig-GHE) samples are prepared through complementary metal-oxide-semiconductor-compatible fabrication processes except the final addition of ionic liquid electrolyte covering the exposed graphene channel and the separate gate-electrode area. The enhanced carrier tunability by ionic gating enables this ig-GHE device to be extremely sensitive to magnetic fields in low-voltage-operation regimes. Further electrical characterization indicates that the operation window is limited by the nonuniform carrier concentration over the channel under high bias conditions. The drain-current-normalized magnetic resolution of the device measured using the low-frequency noise technique is comparable to the previously reported values despite its significant low power consumption.

A review on graphene-based nanocomposites for electrochemical and fluorescent biosensors

Biosensors with high sensitivity, selectivity and a low limit of detection, reaching nano/picomolar concentrations of biomolecules, are important to the medical sciences and healthcare industry for evaluating physiological and metabolic parameters.

Two-dimensional porphyrin-based covalent organic framework: A novel platform for sensitive epidermal growth factor receptor and living cancer cell detection

A porphyrin-based covalent organic framework (denoted as p-COF) was synthesized by a simple oil-bath method and exploited as a novel sensing layer for immobilizing epidermal growth factor receptor (EGFR)-targeting aptamer strands to detect trace EGFR and living michigan cancer foundation-7 (MCF-7) cells for the first time. p-COF presented a nanosheet-like structure, large cavities, rich nitrogen-bearing groups, high electrochemical activity, excellent bioaffinity, low toxicity, and good stability in aqueous solution; the microstructural features of this material enabled strong immobilization of the aptamer strands. Interactions between the aptamer strands and EGFR significantly changed the electrochemical signals of the modified electrode due to the formation of an aptamer-EGFR complex. The p-COF-based aptasensor exhibited an extremely low detection limit (LOD) of 5.64 fg·mL^-1 obtained from differential pulse voltammetry and 7.54 fg·mL^-1 originated from electrochemical impedance spectroscopy with a broad linear detection range of 0.05-100 pg·mL^-1 of the EGFR concentration. When detecting living MCF-7 cells, the p-COF-based aptasensor showed an LOD of 61 cell·mL^-1 with a linear detection range of 500 × 10⁵ cell·mL^-1. The fabricated aptasensor exhibited high selectivity, good stability, reproducibility, acceptable recyclability, and favorable applicability in human serum samples. We believe that the developed p-COF-based aptasensor is a potential candidate for the sensitive detection of target cancer markers or living cells.

Detection of Bisphenol A Using DNA-Functionalized Graphene Field Effect Transistors Integrated in Microfluidic Systems

Bisphenol A (BPA) detection has attracted much attention recently for its importance to food safety and environment. The DNA-functionalized solution-gated graphene transistors are integrated in microfluidic systems and used for recycling detections of BPA for the first time. In the presence of BPA, both single- and double-stranded DNA molecules are detached and released from the graphene surface in aqueous solutions, leading to the change of device electrical performance. The channel currents of the devices change monotonically with the concentration of BPA. Moreover, the devices modified with double-stranded DNA are more sensitive to BPA and show the detection limit down to 10 ng/mL. The highly sensitive label-free BPA sensors are expected to be used for convenient BPA detections in many applications.

Gold nanorod embedded novel 3D graphene nanocomposite for selective bio-capture in rapid detection of Mycobacterium tuberculosis

Tuberculosis (TB) is a chronic and infectious airborne disease which requires a diagnosing system with high sensitivity and specificity. However, the traditional gold standard method for TB detection remains unreliable with low specificity and sensitivity. Nanostructured composite materials coupled with impedimetric sensing utilised in this study offered a feasible solution. Herein, novel gold (Au) nanorods were synthesized on 3D graphene grown by chemical vapour deposition. The irregularly spaced and rippled morphology of 3D graphene provided a path for Au nanoparticles to self-assemble and form rod-like structures on the surface of the 3D graphene. The formation of Au nanorods were showcased through scanning electron microscopy which revealed the evolution of Au nanoparticle into Au islets. Eventually, it formed nanorods possessing lengths of ~ 150 nm and diameters of ~ 30 nm. The X-ray diffractogram displayed appropriate peaks suitable to defect-free and high crystalline graphene with face centered cubic Au. The strong optical interrelation between Au nanorod and 3D graphene was elucidated by Raman spectroscopy analysis. Furthermore, the anchored Au nanorods on 3D graphene nanocomposite enables feasible bio-capturing on the exposed Au surface on defect free graphene. The impedimetric sensing of DNA sequence from TB on 3D graphene/Au nanocomposite revealed a remarkable wide detection linear range from 10 fM to 0.1 µM, displays the capability of detecting femtomolar DNA concentration. Overall, the novel 3D graphene/Au nanocomposite demonstrated here offers high-performance bio-sensing and opens a new avenue for TB detection.

Label-Free Electrochemical Detection of Vanillin through Low-Defect Graphene Electrodes Modified with Au Nanoparticles

Graphene is an excellent modifier for the surface modification of electrochemical electrodes due to its exceptional physical properties and, for the development of graphene-based chemical and biosensors, is usually coated on glassy carbon electrodes (GCEs) via drop casting. However, the ease of aggregation and high defect content of reduced graphene oxides degrade the electrical properties. Here, we fabricated low-defect graphene electrodes by catalytically thermal treatment of HPHT diamond substrate, followed by the electrodeposition of Au nanoparticles (AuNPs) with an average size of ≈60 nm on the electrode surface using cyclic voltammetry. The Au nanoparticle-decorated graphene electrodes show a wide linear response range to vanillin from 0.2 to 40 µM with a low limit of detection of 10 nM. This work demonstrates the potential applications of graphene-based hybrid electrodes for highly sensitive chemical detection.

Highly Sensitive and Selective Potassium Ion Detection Based on Graphene Hall Effect Biosensors

Potassium (K⁺) ion is an important biological substance in the human body and plays a critical role in the maintenance of transmembrane potential and hormone secretion. Several detection techniques, including fluorescent, electrochemical, and electrical methods, have been extensively investigated to selectively recognize K⁺ ions. In this work, a highly sensitive and selective biosensor based on single-layer graphene has been developed for K⁺ ion detection under Van der Pauw measurement configuration. With pre-immobilization of guanine-rich DNA on the graphene surface, the graphene devices exhibit a very low limit of detection (≈1 nM) with a dynamic range of 1 nM–10 μM and excellent K⁺ ion specificity against other alkali cations, such as Na⁺ ions. The origin of K⁺ ion selectivity can be attributed to the fact that the formation of guanine-quadruplexes from guanine-rich DNA has a strong affinity for capturing K⁺ ions. The graphene-based biosensors with improved sensing performance for K⁺ ion recognition can be applied to health monitoring and early disease diagnosis.

Construction and Potential Applications of Biosensors for Proteins in Clinical Laboratory Diagnosis

Biosensors for proteins have shown attractive advantages compared to traditional techniques in clinical laboratory diagnosis. In virtue of modern fabrication modes and detection techniques, various immunosensing platforms have been reported on basis of the specific recognition between antigen-antibody pairs. In addition to profit from the development of nanotechnology and molecular biology, diverse fabrication and signal amplification strategies have been designed for detection of protein antigens, which has led to great achievements in fast quantitative and simultaneous testing with extremely high sensitivity and specificity. Besides antigens, determination of antibodies also possesses great significance for clinical laboratory diagnosis. In this review, we will categorize recent immunosensors for proteins by different detection techniques. The basic conception of detection techniques, sensing mechanisms, and the relevant signal amplification strategies are introduced. Since antibodies and antigens have an equal position to each other in immunosensing, all biosensing strategies for antigens can be extended to antibodies under appropriate optimizations. Biosensors for antibodies are summarized, focusing on potential applications in clinical laboratory diagnosis, such as a series of biomarkers for infectious diseases and autoimmune diseases, and an evaluation of vaccine immunity. The excellent performances of these biosensors provide a prospective space for future antibody-detection-based disease serodiagnosis.