Modification of collagen with a natural derived cross-linker, alginate dialdehyde

Silver carp swim bladder collagen derived from deep eutectic solvents: Enhanced solubility against pH and NaCl stresses

Deep eutectic solvents (DESs) are renowned in chemical and food industries for their eco-friendly extraction efficacy. Silver carp swim bladders, a collagen-rich byproduct of surimi production, are underutilized, resulting in considerable protein waste. Traditionally, collagen extraction has relied on harsh acids, contributing to environmental pollution and producing collagens with limited solubility, thus constraining their applications. This study evaluated DESs compared to conventional acids in extracting collagen, focusing on structural and solubility variations. Notably, urea-based DESs (urea-lactic acid: U-LA, 1:10, w/v) achieved the highest hydroxyproline recovery rates (∼ 94 %), comparable to acetic acid (AA, 1:20, w/v), but with half the solid-liquid ratio. Unlike acid-extracted collagen, which preserved the triple-helical structure, urea-based DESs partially disrupted this configuration by reducing intramolecular hydrogen bonding within collagen. However, these solvents simultaneously increased intermolecular hydrogen bonding. This alteration significantly enhanced collagen's solubility, maintaining over 60 % across a broad pH range (1-10) and various NaCl concentrations (0-6 %, w/v). Furthermore, urea-acetic acid (U-AA) extracted collagen exhibited the highest maximum transition temperature (solid state, Tmax = 101.94 °C) and gel strength (165 g). The findings suggest that urea-based DESs not only enhance collagen recovery rates but also its solubility and gelation properties, broadening its potential applications in cosmetics, food products, and biomaterials.

Surface Modification of Dentin Powder With Alginate and Evaluation of Its Effects on the Viability and Proliferation of Dental Pulp Stem Cells (In Vitro), Its Biocompatibility (In Vivo)

INTRODUCTION

This study aimed to synthesize dentin powder surface modified with alginate, a potential substance for dental pulp regeneration, and evaluate its effects on the viability and proliferation of human dental pulp stem cells in vitro and its biocompatibility in vivo.

METHODS

In the in vitro phase, dentin powder was synthesized in 3 size groups (150-250 μm, 250-500 μm, and 500-1000 μm) after demineralization and atelopeptidization which is used to remove dentin collagen telopeptides and eliminate host immune response. Surface modification with alginate was performed and followed by field-emission scanning electron microscopy, energy dispersive X-ray spectroscopy, and cell viability and proliferation testing for 14 days with human dental pulp stem cells studied. In the in vivo phase, dentin powders were implanted in rat calvarial defects for 8 weeks, and histologic analysis was conducted. All nonparametric data were analyzed with the Kruskal-Wallis test, and all the quantitative data were analyzed by 1-way analysis of variance using SPSS, and P < .05 was considered statistically significant.

RESULTS

Demineralization and atelopeptidization were successful in all groups. Cell viability was optimal and equal (P > .05) in all groups. The 500- to 1000-μm group exhibited significantly higher cell proliferation (P < .05). Histologic assessment shows acceptable biocompatibility in all groups; the angiogenesis score was significantly greater in both 250-500 and 500-1000, and minimal inflammatory response was noted in the 500- to 1000-μm group, and the amount of newly formed bone in this group was higher than other groups.

CONCLUSIONS

Surface modification of demineralized and atelopeptidized dentin powder with alginate enhanced surface physical properties and cell proliferation while showing great biocompatibility within tissue and reducing the host immune response. These findings hold promise for dentin-pulp complex regeneration.

Use of marine occurrent extracts to enhance the stability of dentin extracellular matrix

Chitosan (CS) and phloroglucinol (PhG), two extracts abundantly found in marine life, were investigated for their ability to biomodify demineralized dentin by enhancing collagen crosslinks and improving dentin extracellular matrix (ECM) mechanical and biochemical stability. Dentin obtained from non-carious extracted human molars were demineralized with phosphoric acid. Baseline Fourier-transform infrared (FTIR) spectra, apparent flexural elastic modulus (AE) and dry mass (DM) of each specimen were independently acquired. Specimens were randomly incubated for 5 min into either ultrapure water (no-treatment), 1% glutaraldehyde (GA), 1% CS or 1% PhG. Water and GA were used, respectively, as a negative and positive control for collagen crosslinks. Specimens' post-treatment FTIR spectra, AE, and DM were obtained and compared with correspondent baseline measurements. Additionally, the host-derived proteolytic activity of dentin ECM was assessed using hydroxyproline assay (HYP) and spectrofluorometric analysis of a fluorescent-quenched substrate specific for matrix metalloproteinases (MMPs). Finally, the bond strength of an etch-and-rinse adhesive was evaluated after application of marine compounds as non-rinsing dentin primers. Dentin specimens FTIR spectral profile changed remarkably, and their AE increased significantly after treatment with marine compounds. DM variation, HYP assay and fluorogenic substrate analysis concurrently indicated the biodegradation of CS- and PhG-treated specimens was significantly lesser in comparison with untreated specimens. CS and PhG treatments enhanced biomechanical/biochemical stability of demineralized dentin. These novel results show that PhG is a primer with the capacity to biomodify demineralized dentin, hence rendering it less susceptible to biodegradation by host-proteases.

Multifunctional fish-skin collagen-based hydrogel sealant with dual-dynamic-bond cross-linked for rapid hemostasis and accelerated wound healing

Collagen (COL) is the most widespread functional protein. Designing and developing dual-dynamic-bond cross-linked COL adhesive hydrogel sealants with multifunctional is highly advantageous for achieving a superior wound closure effect and hemostasis. In this study, we developed hybrid hydrogels consisting of fish-skin COL, oxidized sodium alginate (OSA), borax and polyvinyl alcohol (PVA) to enhance full-thickness wound healing. The hydrogels were furnished with first-rate self-healing capabilities through the dual-dynamic-bond cross-linking of dynamic Schiff base bonds (COL-OSA) and diol boric acid bonds (OSA-borax) with reversible breakage and re-formation. Moreover, the incorporation of PVA stimulated the formation of hydrogen bonds in the system, bolstering the stability of the hydrogel framework. The prepared hydrogel manifests self-healing, injectability, multifunctional adhesiveness and biodegradability. In vivo assessment of the hemostatic capacity of COSP20 hydrogel was superior to gauze both in the mice liver injury model and mice tail amputation model. In addition, a full-thickness skin wound model in mice revealed that the COSP20 hydrogel facilitated faster wound closure by accelerating reepithelialization, COL deposition and angiogenesis. These findings illustrate the potential of hybrid fish-skin COL-based hydrogels to enhance wound healing and promote rapid tissue repair, and provide new possibilities for the effective utilization of marine fishery resources.

Novel synergistic cross-linking ameliorate ready-to-eat sea cucumber deterioration and its quantum chemical analysis

Synergistic cross-linkers could improve the taste acceptability of ready-to-eat sea cucumber (RSC). Besides, the hardness of RSC was increased by 331.00% and 266.87% after synergistic cross-linking. Synergistic cross-linking treatment could ameliorate the non-enzymatic degradation of RSC collagen and polysaccharides. Gaussian calculations results showed that dipeptides containing asparagine residues may have different reaction pathways. The main cleavage pathways of CH3CO-Asn-Gly-NHCH3 (NG) might be water-assisted side chain cyclization, stepwise cyclamide hydrolysis via a Gemdiol Intermediate, deamination, and peptide bond breakage. The relative free energy of cyclamide hydrolysis process of NG was increased by 8.2 kcal/mol after synergistic cross-linking. The mass spectrometry results showed that typical peptides could cleavage at NG, CH3CO-Asn-Lys-NHCH3 (NK) and CH3CO-Asn-Leu-NHCH3 (NL) sites after heating, which justified the breakage pattern of peptides in Gaussian calculations. It can offer a comprehensive theoretical basis for the processing of the ready-to-eat sea cucumber with storage stability.

Modulatory role of terminal monomeric flavan-3-ol units in the viscoelasticity of dentin

Flavan-3-ol monomers are the building blocks of proanthocyanidins (PACs), natural compounds from plants shown to mediate specific biologic activities on dentin. While the stereochemistry of the terminal flavan-3-ols, catechin (C) versus epicatechin (EC), impacts the biomechanical properties of the dentin matrix treated with oligomeric PACs, structure-activity relationships driving this bioactivity remain elusive. To gain insights into the modulatory role of the terminal monomers, two highly congruent trimeric PACs from Pinus massoniana only differing in the stereochemistry of the terminal unit (Trimer-C vs. Trimer-EC) were prepared to evaluate their chemical characteristics as well as their effects on the viscoelasticity and biostability of biomodified dentin matrices via infrared spectroscopy and multi-scale dynamic mechanical analyses. The subtle alteration of C versus EC as terminal monomers lead to distinct immediate PAC-trimer biomodulation of the dentin matrix. Nano- and micro-dynamic mechanical analyses revealed that Trimer-EC increased the complex moduli (0.51 GPa) of dentin matrix more strongly than Trimer-C (0.26 GPa) at the nanoscale length (p < 0.001), whereas the reverse was found at the microscale length (p < .001). The damping capacity (tan δ) of dentin matrix decreased by 70% after PAC treatment at the nano-length scale, while increased values were found at the micro-length scale (~0.24) compared to the control (0.18 ; p < .001). An increase in amide band intensities and a decrease of complex moduli was observed after storage in simulated body fluid for both Trimer-C and Trimer-EC modified dentin. The stereochemical configuration of the terminal monomeric units, C and EC, did not impact the chemo-mechanical stability of dentin matrix.

The effect of a bionic bone ionic environment on osteogenesis, osteoimmunology, and in situ bone tissue engineering

Bone, a mineralized tissue, continuously undergoes remodeling. It is a process that engages the mineralization and demineralization of the bone matrix, orchestrated by the interactions among cells and cell-secreted biomolecules under the bone ionic microenvironment (BIE). The osteoinductive properties of the demineralized organic bone matrix and many biological factors have been well-investigated. However, the impact of the bone ionic environment on cell differentiation and osteogenesis remains largely unknown. In this study, we extracted and isolated inorganic bone components (bone-derived monetite, BM) using a low-temperature method and, for the first time, investigated whether the BIE could actively affect cell differentiation and regulate osteoimmune reactions. It was evidenced that the BIE could foster the osteogenesis of human bone marrow stromal cells (hBMSCs) and promote hBMSCs mineralization without using osteogenic inductive agents. Interestingly, it was noted that BIE resulted in intracellular mineralization, evidenced by intracellular accumulation of carbonate hydroxyapatite similar to that oberved in osteoblasts cultured in osteoinductive media. Additionally, BIE was found to enhance osteogenesis by generating a favorable osteoimmune environment. In a rat calvarial bone defect model, the osteogenic capacity of BIE was evaluated using a collagen type I-impregnated BM (Col-BM) composite. It showed that Col-BM significantly promoted new bone formation in the critical-size bone defect areas. Taken together, this is the first study that investigated the influence of the BIE on osteogenesis, osteoimmunology, and in situ bone tissue engineering. The innate osteoinductive potential of inorganic bone components, both in vitro and in vivo, not only expands the understanding of the BIE on osteogenesis but also benefits future biomaterials engineering for bone tissue regeneration.

High-strength and high-toughness ECM films with the potential for peripheral nerve repair

Extracellular matrix (ECM) scaffolds are widely applied in the field of regeneration as the result of their irreplaceable biological advantages, and the preparation of ECM scaffolds into ECM hydrogels expands the applications to some extent. However, weak mechanical properties of current ECM materials limit the complete exploitation of ECM's biological advantages. To enable ECM materials to be utilized in applications requiring high strength, herein, we created a kind of new ECM material, ECM film, and evaluated its mechanical properties. ECM films exhibited outstanding toughness with no cracks after arbitrarily folding and crumpling, and dramatically high strength levels of 86 ± 17.25 MPa, the maximum of which was 115 MPa. Such spectacular high-strength and high-toughness films, containing only pure ECM without any crosslinking agents and other materials, far exceed current pure natural polymer gel films and even many composite gel films and synthetic polymer gel films. In addition, both PC12 cells and Schwann cells cultured on the surface of ECM films, especially Schwann cells, showed good proliferation, and the neurite outgrowth of the PC12 cells was promoted, indicating the application potential of ECM film in peripheral nerve repair.

Dialdehyde carbohydrates - Advanced functional materials for biomedical applications

Dialdehyde carbohydrates (DCs) have found applications in a wide range of biomedical field due to their great versatility, biocompatibility/biodegradability, biological properties, and controllable chemical/physical characteristics. The presence of dialdehyde groups in carbohydrate structure allows cross-linking of DCs to form versatile architectures serving as interesting matrices for biomedical applications (e.g., drug delivery, tissue engineering, and regenerative medicine). Recently, DCs have noticeably contributed to the development of diverse physical forms of advanced functional biomaterials i.e., bulk architectures (hydrogels, films/coatings, or scaffolds) and nano/-micro formulations. We underline here the current scientific knowledge on DCs, and demonstrate their potential and newly developed biomedical applications. Specifically, an update on the synthesis approach and functional/bioactive attributes is provided, and the selected in vitro/in vivo studies are reviewed comprehensively as examples of the latest progress in the field. Moreover, safety concerns, challenges, and perspectives towards the application of DCs are deliberated.

Natural and Synthetic Polymeric Biomaterials for Application in Wound Management

Biomaterials are at the forefront of the future, finding a variety of applications in the biomedical field, especially in wound healing, thanks to their biocompatible and biodegradable properties. Wounds spontaneously try to heal through a series of interconnected processes involving several initiators and mediators such as cytokines, macrophages, and fibroblasts. The combination of biopolymers with wound healing properties may provide opportunities to synthesize matrices that stimulate and trigger target cell responses crucial to the healing process. This review outlines the optimal management and care required for wound treatment with a special focus on biopolymers, drug-delivery systems, and nanotechnologies used for enhanced wound healing applications. Researchers have utilized a range of techniques to produce wound dressings, leading to products with different characteristics. Each method comes with its unique strengths and limitations, which are important to consider. The future trajectory in wound dressing advancement should prioritize economical and eco-friendly methodologies, along with improving the efficacy of constituent materials. The aim of this work is to give researchers the possibility to evaluate the proper materials for wound dressing preparation and to better understand the optimal synthesis conditions as well as the most effective bioactive molecules to load.

Effects of proanthocyanidins and dialdehyde chitosan on the proliferation and differentiation of bovine myoblast for cultured meat production

Cultured meat technology intends to manufacture meat by cultivating muscle stem cells in vitro, which is an emerging methodology in meat production. However, the insufficient stemness of bovine myoblasts cultivated in vitro declined the ability of cell expansion and myogenic differentiation, which limited the production of cultured meat. Therefore, in this study, we introduced proanthocyanidins (PC, natural polyphenolic compounds) and dialdehyde chitosan (DAC, natural polysaccharides) to explore the effects of proliferation and differentiation of bovine myoblasts in vitro. The experiment results revealed that PC and DAC promoted cell proliferation by improving the transition from G1 to the S phase as well as cell division in G2. Meanwhile, the myogenic differentiation of cells was further boosted by the combined PC and DAC up-regulation of MYH3 expression. Moreover, the study revealed the synergistic effect of PC and DAC on enhancing the structural stability of collagen, and bovine myoblasts demonstrated excellent growth and dispersion ability on collagen scaffolds. It is concluded that both PC and DAC promote the proliferation and differentiation of bovine myoblasts, contributing to the development of cultured meat production systems.

Insight into the composite assembly process, nanofibril structure and stability of undenatured type II collagen in the presence of different types of nanocelluloses

Four types of nanocelluloses (CNs), including cellulose nanocrystals (CNC), cellulose nanofibrils (CNF), cationic etherified nanocellulose (CCNF) and TEMPO-oxidized nanocellulose (TOCNF), were incorporated into the assembly process of undenatured type II collagen (UC-II). In the presence of CNs, the kinetics of UC-II composite assembly slightly fluctuated and the magnitude of UC-II assembly increased (from 59.93 to 66.83-85.06 %). CNC and CNF disrupted the triple helix structure of UC-II while CCNF and TOCNF had weak impact on it. Hydrogen bonding and hydrophobic interactions were dominant driving forces of UC-II/CNs, and electrostatic interactions were also involved in the fabrication of UC-II/CCNF and UC-II/TOCNF. UC-II/CNs exhibited distinct nanostructures due to the differences in shape, level, and surface group of CNs. CCNF and TOCNF contributed to the enhanced physical stability due to the increased surface charge. In addition, the thermal stability and rheological properties of UC-II/CNs were also improved. The composite assembly process, nanofibril structure and stability of UC-II in the presence of different types and levels of CNs, which was useful to develop the novel composite nanofibrils for the application in functional foods.

Synthesis of oxidized sodium alginate and its electrospun bio-hybrids with zinc oxide nanoparticles to promote wound healing

Electrospun fibers provide a promising platform for wound healing; however, they lack requisite characteristics for wound repair, including antibacterial and anti-inflammatory properties and angiogenic ability. Sodium alginate (SA) is being used for different types of applications. However, the poor spinnability of SA restricts its applications. The objectives of this study were three-fold: a) to synthesize oxidized sodium alginate (OSA) to improve its spinnability, b) to fabricate composite fibrous membranes by blending OSA along with zinc oxide nanoparticles (ZnO-NPs), and c) to decipher antibacterial and anti-inflammatory properties as well as biocompatibility of membranes in vitro and in vivo. OSA displaying different oxidation degrees (Dox (%)) was synthesized by varying the molar ratio of sodium periodate to SA. OSA (Dox, ∼48 %) afforded smooth and uniform fibers; 0.5 wt% of adipic dihydrazide (ADH) evolved into structurally stable and water-insoluble membranes. Composite fibrous membranes containing 2 wt% of ZnO-NPs displayed good biocompatibility and bactericidal effect against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) in vitro. In addition, composite membranes showed remarkable epithelialization, neovascularization, and anti-inflammatory response than that of the membranes devoid of ZnO-NPs. Conclusively, these composite fibrous membranes may have broad implications for wound healing applications.

Strategical development of chrome-free tanning agent by integrating layered double hydroxide with starch derivatives

The development of sustainable and eco-friendly leather industry requires green tanning agents because of unbounded chromium (easily converted into hazardous Cr-VI) in chrome tanned leather. In this study, a chrome-free tanning agent (OS-LDHs) was established by integrating layered double hydroxide (magnesium aluminum zirconium hydrotalcite, LDHs) with starch derivatives. A series of oxidized starch (OS) were prepared as masking agents for LDHs tanning process. Among them, the weight-average molecular weight (Mw) of 1685 g/mol could be reached, which will promise the well-distribution of OS. The SEM and EDS analysis confirmed the uniform penetration of OS-LDHs, avoiding accumulation on the surface of crust leather. Notably, leather tanned by OS-LDHs achieved shrinkage temperature of 66.7 °C, porosity of 75.51 % and tear strength of 66.7 N/mm. Not only the hydrogen bond but also the coordination between NH₂, COOH in collagen and OS-2-LDHs improved the thermal stability of leather without destroying the collagen triple helix.

3d oxidized alginate-porcine liver acellular collagen droplets for tumor microenvironment mimicking

The traditional 2d culture has been proved inferior to reproduce the subtle interaction between cell-to-cell and cell-to-extracellular matrix (ECM) in tumor microenvironment (TME) and collagen in ECM contributes to various malignancies of tumors. Hence, the 3d model contained with collagen may overcome the shortcomings of 2d culture. In this study, the in vitro TME mimicking matrix was prepared by coupling porcine liver-derived collagen (COL) and the dialdehyde group of partially oxidized alginate (OA), namely OA-COL, and the 3d OA-COL droplets were polymerized by divalent calcium ions. In the 3d OA-COL droplets, cancer cells displayed vigorous proliferation, and the cells grew in clusters and formed a unique spindle like clone. Quantitative analysis proved that various gene transcription and protein expression were up-regulated for the cells in the 3d OA-COL droplets, including F-actin reassembling, focal adhesion, pseudopodia formation, and the proteins involved in epithelial-to-mesenchymal transition (EMT). The 3d OA-COL droplets induced the cells with strengthened polarity, invasiveness, higher IC50, and manifested stronger tumorigenicity in vivo. The fabricated 3d OA-COL droplets reproduced a variety of TME parameters, constructed an in vitro model similar to the TME in vivo, and it may facilitate many investigations in cell biology and tumor biology.

Origin of critical nature and stability enhancement in collagen matrix based biomaterials: Comprehensive modification technologies

Collagen is the most abundant protein in animals and one of the most important extracellular matrices that chronically plays an important role in biomaterials. However, the major concern about native collagen is the lack of its thermal stability and weak resistance to proteolytic degradation. Currently, a series of modification technologies have been explored for critical nature and stability enhancement in collagen matrix-based biomaterials, and prosperously large-scale progress has been achieved. The establishment of covalent bonds among collagen noumenon has been verified assuringly to have pregnant influences on its physicochemical properties and biological properties, enlightening to discuss the disparate modification technologies on specific effects on the multihierarchical structures and pivotal performances of collagen. In this review, various existing modification methods were classified from a new perspective, scilicet whether to introduce exogenous substances, to reveal the basic scientific theories of collagen modification. Understanding the role of modification technologies in the enhancement of collagen performance is crucial for developing novel collagen-based biomaterials. Moreover, the different modification effects caused by the interaction sites between the modifier and collagen, and the structure-activity relationship between the structure of the modifier and the properties of collagen were reviewed.

Tunable mechanical behavior of collagen-based films: A comparison of celluloses in different geometries

Collagen (Col) films were reinforced by celluloses in different geometries: microcrystalline cellulose (MCC), cellulosic fines (CF), cellulose nanofiber (CNF) and cellulose nanocrystals (CNC). The reinforcement mechanisms were investigated by the elastoplasticity and fracture appearance. Compared with the fracture stress of collagen film (67.5 MPa), the Col-CNF films effectively borne the stress (95.8 MPa) by intercrystalline fracture, ascribing the abundant hydrogen bonding and mechanical locking between cellulose and collagen. The toughness of Col-CF films was increased by the interfibrillar slippage of CF and pull-off of CF within the matrix, improving the strain-to-break from 8.37% to 12.13%. The films added with MCC and CNC weaken the mechanical behavior, due to the defects and lack of mechanical locking. Besides, the effects of celluloses' geometries on the thickness, density, water-tightness, thermal stability, crystallinity and FTIR of films were also investigated. These provide the evidence that the geometries of fillers diversely improve the behaviors of collagen film offering strategies for the film with adjustable mechanical properties.

Novel Karaya Gum Derivatives Produced by Alkaline Hydrolysis and Periodate Oxidation for Active Packaging with Cinnamaldehyde

This study aims to produce novel derivatives of karaya gum using chemical modification and then apply them for active packaging with cinnamaldehyde as the main active component. Native karaya gum (NKG) was hydrolyzed using sodium hydroxide to yield hydrolyzed karaya gum (HKG), which then was oxidized using sodium periodate to yield hydrolyzed-oxidized karaya gum (HOKG). For comparison, NKG was also directly oxidized using sodium periodate to produce oxidized karaya gum (OKG). FTIR spectra confirmed the removal of acetyl groups after alkaline hydrolysis and the formation of carbonyl groups with subsequent formation of hemiacetal and acetal structures after periodate oxidation. The alkaline hydrolysis and the periodate oxidation resulted in opposite effects on the hydrophilicity of the gum: hydrolysis increased solubility, moisture uptake, and viscosity, while periodate oxidation decreased these properties. We then produced films from corn starch and these gums (5% $w/w$ gum/starch) and properties of the films were studied. Hydrolysis of KG resulted in higher tensile strength, higher transparency but lower puncture strength and antifungal activity against of the films, while periodate oxidation exerted the opposite effects. The incorporation of 5% cinnamaldehyde ( $w/w$ of starch) exerted strong antifungal and antibacterial effects on the films against Colletotrichum gloeosporioides and Escherichia coli, which are useful in active packaging. The active packages based on the novel derivatives of KG can find applications in the agricultural, food, and pharmaceutical industries.

Scaffolds Loaded with Dialdehyde Chitosan and Collagen—Their Physico-Chemical Properties and Biological Assessment

In this work, dialdehyde chitosan (DAC) and collagen (Coll) scaffolds have been prepared and their physico-chemical properties have been evaluated. Their structural properties were studied by Fourier Transform Infrared Spectroscopy with Attenuated Internal Reflection (FTIR–ATR) accompanied by evaluation of thermal stability, porosity, density, moisture content and microstructure by Scanning Electron Microscopy—SEM. Additionally, cutaneous assessment using human epidermal keratinocytes (NHEK), dermal fibroblasts (NHDF) and melanoma cells (A375 and G-361) was performed. Based on thermal studies, two regions in DTG curves could be distinguished in each type of scaffold, what can be assigned to the elimination of water and the polymeric structure degradation of the materials components. The type of scaffold had no major effect on the porosity of the materials, but the water content of the materials decreased with increasing dialdehyde chitosan content in subjected matrices. Briefly, a drop in proliferation was noticed for scaffolds containing 20DAC/80Coll compared to matrices with collagen alone. Furthermore, increased content of DAC (50DAC/50Coll) either significantly induced the proliferation rate or maintains its ratio compared to the control matrix. This delivery is a promising technique for additional explorations targeting therapies in regenerative dermatology. The using of dialdehyde chitosan as one of the main scaffolds components is the novelty in terms of bioengineering.

Fabrication of oxidized sodium alginate-collagen heterogeneous bilayer barrier membrane with osteogenesis-promoting ability

Guided bone regeneration technique is an effective approach to repair bone defects, in which a barrier membrane is essential. However, the collagen barrier membranes commonly used lose stability quickly, leading to connective tissue invasion and failure of osteogenesis. Herein, we presented an oxidized sodium alginate (OSA)-collagen heterogeneous bilayer barrier membrane with well-controlled pore size and osteogenesis-promoting ability. The OSA crosslinking significantly improved the structural stability, compressive strength, swelling behavior, and slowed down the biodegradation rate of collagen membranes. Meanwhile, the collagen-based membranes exhibited superior cytocompatibility, osteogenesis-promotion, and barrier function against fibroblasts. Especially, the osteogenic differentiation was most promoted on the membrane with a large pore size (240-310 μm), while the barrier function was most improved on the membrane with a small pore size (30-60 μm). Then the above two membranes were combined together to obtain a heterogeneous bilayer membrane. This bilayer barrier membrane showed excellent osteogenesis-promoting ability in rats.

The mechanism of molecular cross-linking against nonenzymatic degradation in the body wall of ready-to-eat sea cucumber

Ready-to-eat sea cucumbers (RSC) treated by high pressure steam were easily degraded during storage. Celery (Apium graveolens, AG) and chlorogenic acid (CA) were screened for enhancing the stability of RSC. After RSC cross-linked by AG or CA, the hardness was significantly increased by 108% or 254% at 30 d, and the relaxation time decrease by 31.90 or 39.89 ms, and the proportion of T₂₃ reduced by 0.40% or 1.15%. The crosslinked RSC exhibited smaller pore size with finer collagen fibrils. CA treatment caused the secondary structure changes in RSC. In addition, it also inhibited the break of peptide bonds in RSC collagen, observing the decrease of free hydroxyproline level from 46.63 to 34.53 μg/g, and the reduction of free ammonia nitrogen from 20.96 to 15.30 μmol/g. Therefore, AG and CA will have an important application in RSC processing industry.

Changes to dentin extracellular matrix following treatment with plant-based polyphenols

This study investigated whether treatment with plant-based polyphenols (PB-P) affected the biochemical and/or biomechanical properties of dentin extracellular matrix (ECM). Three PB-Ps were evaluated: luteolin (LT), galangin (GL), and proanthocyanidin (PAC). Because dentin ECM requires demineralization before treatment, this study also assessed the effect of these PB-Ps on dentin demineralized by two different chemicals. Dentin samples from extracted third molars were obtained, sectioned, and randomly assigned for demineralization with either phosphoric acid (PA) or ethylenediaminetetraacetic acid (EDTA). Following demineralization, baseline infrared (IR) spectra and apparent elastic modulus (AE) of each specimen were independently acquired. Based upon these initial tests, samples were randomly assigned to one of the PB-P treatments to ensure that distribution of baseline AE was similar across treatment groups. IR and AE specimens were individually immersed in either 0.2% LT, 0.4% GL or 1% PAC for 2 min. IR spectra of treated samples were compared to baseline IR spectra, looking for any interaction of PB-Ps with the demineralized dentin. The IR spectrum and AE of each PB-P-treated specimen were compared with their own correspondent baseline measurement. The ability of PB-Ps to inhibit proteolytic activity of dentin ECM was assessed by the hydroxyproline assay. Finally, the effect of PB-Ps on immediate bond strength of a dental adhesive to PA- or EDTA-etched dentin was also evaluated. PB-Ps exhibited distinctively binding affinity to dentin ECM and promoted significant increase in AE. PB-P treatment reduced the degradation rate of dentin ECM without causing detrimental effect on immediate bond strength to dentin. Our work represents the first-time that LT and GL have been assessed as dentin ECM biomodifiers.

4-Arm PEG-Functionalized Decellularized Pericardium for Effective Prevention of Postoperative Adhesion in Cardiac Surgery

Postoperative adhesions are a very common and serious complication in cardiac surgery, and the development of an effective anti-adhesion membrane showing resistance to the physical stimulus generated by the pulsation of the heart is desirable. In this study, an anti-adhesion material was developed through amine coupling between decellularized bovine pericardia (dBPCs) and 4-arm poly(ethylene glycol) succinimidyl glutarate (4-arm PEG-NHS) for the postoperative care of cardiac surgical patients. The efficacy of the 4-arm PEG-functionalized dBPCs in the prevention of adhesions after cardiac surgery was investigated in a rabbit heart adhesion model. The dBPCs meet the requirements for biocompatibility, flexibility, and sufficient suturable strength, and the 4-arm PEG moieties provide an anti-adhesion effect by the high excluded volume interactions of the PEG chains with proteins. The 4-arm PEG-functionalized dBPCs had a significantly greater anti-adhesion effect than the other materials tested and showed re-establishment of the mesothelial monolayer. These results suggested that the 4-arm PEG-functionalized dBPCs are a favorable material for an anti-adhesion membrane.

Development of novel hyaluronic acid/human-like collagen bio-composite membranes: A facile "surface modification-assembly" approach

The merits of hyaluronic acid (HA) as a representative biological carbohydrate polymers especially in bioactivity and tailorability makes it ideal building block for the engineering of tissue engineering scaffolds. HA-based bio-composites integrate the characteristics of multi-component materials, possessing versatility and further improving the therapeutic efficacy. Human like collagen (HLC), which is hydrophilic, biomimetic, and bio-safe, with human tissue-derived collagen biofunction, has attracted extensive attention worldwide. Herein, we developed a novel method for HA/HLC bio-composite membranes preparation, comprising one-step surface modification-assembly process by which the HLC self-assembles are simultaneously loaded on the oxidized-modified HA (oxi-HA) from the surface/interface micro-scale. Comprehensive material characterizations and in vitro/in vivo biostudies proved that the HLC/oxi-HA composite membranes exhibited significantly enhanced biological activity, hemostatic performances, and wound healing properties compared to that of the pristine HA. The results of this study highlight the great potential of the prepared biomimetic HLC/oxi-HA bio-composites as a new generation of multifunctional HA-based wound-healing materials.

Manipulate the nano-structure of layered double hydroxides via calcination for enhancing immobilization of anionic dyes on collagen fibers

In this work, we present an effective approach for promoting the immobilization of anionic dyes on the collagen fibers of the leather matrix via introducing layered double oxide (LDO), which is obtained by calcining layered double hydroxides (LDH), inspired by incorporating their memory effect and charge effect. The results indicate that the calcination increases specific surface area, oxygen vacancies, and Al³⁺ defects of LDH nanosheets, and the structure of LDH nanosheets can be reconstructed by rehydration. Diffusion behavior of both LDH and LDO nanosheets into the collagen fibers follows the Langmuir model. The LDO nanosheets can penetrate into the collagen fibers more easily and evenly than that of the LDH nanosheets. Moreover, the formation of ionic bonds, hydrogen bonds, and coordination bonds between the nanosheets and the collagen stabilizing the collagen microstructures can endow the collagen fibers with improved thermal stability. Increased porosity of the collagen fibers results in enhanced adsorption and immobilization capacity for anionic dyes on the collagen fibers of the leather matrix in leather post-tanning process. Furthermore, adsorption behavior of anionic dye on the collagen fibers can be well accorded with pseudo-second-order and Langmuir model, exhibiting a monolayer adsorption process. This established cooperative approach will be helpful to extend the application of clay for improving the dyeing performance of leather matrix towards eco-leather manufacture and effectively reduce emission of dyes from the source in leather manufacturing.

Unveiling structure-activity relationships of proanthocyanidins with dentin collagen

OBJECTIVE

To elucidate the structure-activity relationships (SARs) of proanthocyanidins (PACs) with type I collagen using sixteen chemically defined PACs with degree of polymerization (DP) 2-6.

METHODS

Under a dentin model, the biomimicry of PACs with type I collagen was investigated by dynamic mechanical analysis (DMA) and infrared spectroscopy. The dentin matrix was modified with PACs from Pinus massoniana [monomers (Mon-1 and Mon-2), dimers (Dim-1-Dim-4), trimers (Tri-1-Tri-4), tetramers (Tet-1-Tet-5), and hexamer (Hex-1)]. A strain sweep method in a 3-point bending submersion clamp was used to assess the viscoelastic properties [storage (E'), loss (E"), and complex moduli (E*) and tan δ] of the dentin matrix before and after biomodification. Biochemical analysis of the dentin matrix was assessed with FTIR spectroscopy. Data were statistically analyzed using one-way ANOVA and post-hoc tests (α = 0.05).

RESULTS

DP had a significant effect on modified dentin moduli (tetramers ≈ trimers > hexamers ≈ dimers > monomers ≈ control, p < 0.001). Trimers and tetramers yielded 6- to 8-fold increase in the mechanical properties of modified dentin and induced conformational changes to the secondary structure of collagen. Modifications to the tertiary structure of collagen was shown in all PAC modified-dentin matrices.

SIGNIFICANCE

Findings establish three key SARs: (i) increasing DP generally enhances biomimicry potential of PACs in modulating the mechanical and chemical properties of dentin (ii) the secondary structure of dentin collagen is affected by the position of B-type inter-flavanyl linkages (4β → 6 and 4β → 8); and (iii) the terminal monomeric flavan-3-ol unit plays a modulatory role in the viscoelasticity of dentin.

Advanced biomaterials for sustainable applications in the food industry: Updates and challenges

Maintaining the safety and quality of food are major concerns while developing biomaterial based food packaging. It offers a longer shelf-life as well as protection and quality control to the food based on international standards. Nano-biotechnology contributes to a far extent to make advanced packaging by developing multifunctional biomaterials for potential applications providing smarter materials to consumers. Applications of nano-biocomposites may thus help to deliver enhanced barrier, mechanical strength, antimicrobial and antioxidant properties to novel food packaging materials. Starch derived bioplastics, polylactic acid and polyhydroxybutyrate are examples of active bioplastics currently in the food packaging sector. This review discusses the various types of biomaterials that could be used to improve future smarter food packaging, as well as biomaterials' potential applications as food stabilizers, pathogen control agents, sensors, and edible packaging materials. The regulatory concerns related to the use of biomaterials in food packaging and commercially available biomaterials in different fields are also discussed. Development of novel biomaterials for different food packaging applications can therefore guarantee active food packaging in future.

Highly stable collagen scaffolds crosslinked with an epoxidized natural polysaccharide for wound healing

As a biocompatible and bioactive natural tissue engineering collagen scaffold, porcine acellular dermal matrix (pADM) has limitations for the application in tissue regeneration due to its low strength and rapid biodegradation. Herein, to get a good wound dressing, the epoxy group was added to N-(2-hydroxypropyl)-3-trimethylammonium chitosan chloride (HTCC) to synthesize the epoxidized N-(2-hydroxypropyl)-3-trimethylammonium chitosan chloride (EHTCC), and the porcine acellular dermal matrix was modified with EHTCC at different dosage of 0, 4, 8, 12, 16 and 20%. The properties of the EHTCC-pADM were evaluated. The results indicated that the thermal stability and mechanical properties of EHTCC-pADM were remarkably improved, and the natural conformation of the matrix was maintained, which was beneficial to natural and excellent biological properties of the pADM. According to the test results of water contact angle, the hydrophilicity of the material was improved, which is conducive to cell adhesion, proliferation and growth. Cytotoxicity experiments showed that the introduction of EHTCC would not adversely affect the biocompatibility of the materials. In vivo experiments showed that EHTCC-pADM could promote wound healing. In conclusion, EHTCC-pADM is a potential collagen-based dressing for wound healing.

Applications of oxidized alginate in regenerative medicine

Because of its ideal degradation rate and features, oxidized alginate (OA) is selected as an appropriate substitute and has been introduced into hydrogels, microspheres, 3D-printed/composite scaffolds, membranes, and electrospinning and coating materials. By taking advantage of OA, the OA-based materials can be easily functionalized and deliver drugs or growth factors to promote tissue regeneration. In 1928, it was first found that alginate could be oxidized using periodate, yielding OA. Since then, considerable progress has been made in the research on the modification and application of alginate after oxidation. In this article, we summarize the key properties and existing applications of OA and various OA-based materials and discuss their prospects in regenerative medicine.

Is Dialdehyde Chitosan a Good Substance to Modify Physicochemical Properties of Biopolymeric Materials?

The aim of this work was to compare physicochemical properties of three dimensional scaffolds based on silk fibroin, collagen and chitosan blends, cross-linked with dialdehyde starch (DAS) and dialdehyde chitosan (DAC). DAS was commercially available, while DAC was obtained by one-step synthesis. Structure and physicochemical properties of the materials were characterized using Fourier transfer infrared spectroscopy with attenuated total reflectance device (FTIR-ATR), swelling behavior and water content measurements, porosity and density observations, scanning electron microscopy imaging (SEM), mechanical properties evaluation and thermogravimetric analysis. Metabolic activity with AlamarBlue assay and live/dead fluorescence staining were performed to evaluate the cytocompatibility of the obtained materials with MG-63 osteoblast-like cells. The results showed that the properties of the scaffolds based on silk fibroin, collagen and chitosan can be modified by chemical cross-linking with DAS and DAC. It was found that DAS and DAC have different influence on the properties of biopolymeric scaffolds. Materials cross-linked with DAS were characterized by higher swelling ability (~4000% for DAS cross-linked materials; ~2500% for DAC cross-linked materials), they had lower density (Coll/CTS/30SF scaffold cross-linked with DAS: 21.8 ± 2.4 g/cm3; cross-linked with DAC: 14.6 ± 0.7 g/cm3) and lower mechanical properties (maximum deformation for DAC cross-linked scaffolds was about 69%; for DAS cross-linked scaffolds it was in the range of 12.67 ± 1.51% and 19.83 ± 1.30%) in comparison to materials cross-linked with DAC. Additionally, scaffolds cross-linked with DAS exhibited higher biocompatibility than those cross-linked with DAC. However, the obtained results showed that both types of scaffolds can provide the support required in regenerative medicine and tissue engineering. The scaffolds presented in the present work can be potentially used in bone tissue engineering to facilitate healing of small bone defects.

Feasibility Study of Gelatin Preparation from the Bioinspired Collagen Aggregates by a "Two-step" Facile Degradation Method

Gelatin is the putative research hotspot of natural products, but gelatin prepared by traditional alkali methods has seriously affected its applications due to the worryingly low molecular weight and poor gel strength. Herein, we took the lead to extract the distinct gelatin from a kind of bioinspired collagen aggregate (CA) by a two-step controlled degradation method. Structural analysis suggested that the CA better preserves the natural aggregated structure of nature collagen (typical D-periodic cross-striated pattern). Compared with the gelatin gelatinized by the conventional alkali method (G-Al) and commercial gelatin (CG), the gelatin (G-CA) from CA had a wide molecular weight distribution range, high transparency, high viscosity, and strong gel strength as expected. Meanwhile, the G-CA film exhibited better mechanical performance and thermostability than CG and G-Al films, and water vapor permeability was also higher in the G-CA film, whereas water solubility was higher in the CG and G-Al films. Thus, the G-CA film is more conducive to the use of food packaging or edible films, exhibiting more potential market application prospects. Notably, G-CA based on CA from waste hide offal provides a way to reuse leather waste resources and further realize green and clean production in leather industry.

Investigations on the general properties of biomass-based aldehyde tanned sheep fur for its selective post-tanning processing

Abstract

Dialdehyde sodium alginate (DSA) is an alternative chrome-free tanning material for fur production. To obtain satisfactory resultant fur and provide suggestions for the usage of DSA in fur making, the general properties of DSA tanned sheep fur were systematically investigated. The tanning mechanism of DSA was analyzed and it was verified that DSA was mainly combined with collagen fiber by forming Schiff base covalent bonds while supplemented by a small number of hydrogen bonds and ionic bonds. Due to the acid sensitivity of Schiff base structure, DSA tanned fur had poor resistance to acid rinsing but had excellent resistance to washing and good fatliquoring performance. Also, it had good resistances to yellowing and reductant. After being retanned by chrome tanning agent, the fur was capable of enduring a high-temperature dyeing process (68 °C for 8 h). Overall, DSA tanned sheep fur had favorable properties under appropriate post-tanning processing conditions to manufacture light-colored or dark-colored fur products with desirable physical properties.

Graphical abstract

Incorporation of gelatin improves toughness of collagen films with a homo-hierarchical structure

In this study, gelatin (type A and type B) with/without transglutaminase (TGase) were added to collagen fiber films to form hierarchical structure and its effects on the film were investigated. The analysis of mechanical properties indicate that gelatin significantly increased the toughness of the collagen film, where the 10 wt% type A gelatin -contained films had highest tensile strength, elongation at break and work of fracture. However, TGase crosslinking compromised the benefits of type A gelatin greatly, while type B gelatin showed a slight improvement, due to the difference in crosslinking activity between them. In the meantime, the hydrogen bonds were formed between the collagen and gelatin according to the results of the Fourier transformation infrared. In general, it is expected that the hierarchical structure formed in the collagen/gelatin films can be used as an effective strategy to enhance the collagen matrix films' mechanical properties.

Advancing bioinks for 3D bioprinting using reactive fillers: A review

The growing demand for personalized implants and tissue scaffolds requires advanced biomaterials and processing strategies for the fabrication of three-dimensional (3D) structures mimicking the complexity of the extracellular matrix. During the last years, biofabrication approaches like 3D printing of cell-laden (soft) hydrogels have been gaining increasing attention to design such 3D functional environments which resemble natural tissues (and organs). However, often these polymeric hydrogels show poor stability and low printing fidelity and hence various approaches in terms of multi-material mixtures are being developed to enhance pre- and post-printing features as well as cytocompatibility and post-printing cellular development. Additionally, bioactive properties improve the binding to the surrounding (host) tissue at the implantation site. In this review we focus on the state-of-the-art of a particular type of heterogeneous bioinks, which are composed of polymeric hydrogels incorporating inorganic bioactive fillers. Such systems include isotropic and anisotropic silicates like bioactive glasses and nanoclays or calcium-phosphates like hydroxyapatite (HAp), which provide in-situ crosslinking effects and add extra functionality to the matrix, for example mineralization capability. The present review paper discusses in detail such bioactive composite bioink systems based on the available literature, revealing that a great variety has been developed with substantially improved bioprinting characteristics, in comparison to the pure hydrogel counterparts, and enabling high viability of printed cells. The analysis of the results of the published studies demonstrates that bioactive fillers are a promising addition to hydrogels to print stable 3D constructs for regeneration of tissues. Progress and challenges of the development and applications of such composite bioink approaches are discussed and avenues for future research in the field are presented. STATEMENT OF SIGNIFICANCE: Biofabrication, involving the processing of biocompatible hydrogels including cells (bioinks), is being increasingly applied for developing complex tissue and organ mimicking structures. A variety of multi-material bioinks is being investigated to bioprint 3D constructs showing shape stability and long-term biological performance. Composite hydrogel bioinks incorporating inorganic bioreactive fillers for 3D bioprinting are the subject of this review paper. Results reported in the literature highlight the effect of bioactive fillers on bioink properties, printability and on cell behavior during and after printing and provide important information for optimizing the design of future bioinks for biofabrication, exploiting the extra functionalities provided by inorganic fillers. Further functionalization with drugs/growth factors can target enhanced printability and local drug release for more specialized biomedical therapies.

Preparation and Characterization of Antibacterial Porcine Acellular Dermal Matrices with High Performance

Infection is a common complication in the process of wound management. An ideal wound dressing is supposed to reduce or even prevent the infection while promoting wound healing. A porcine acellular dermal matrix (pADM) has been already used as a wound dressing in clinic due to its capacity to accelerate wound healing. However, not only is pure pADM not antibacterial, its mechanical properties are poor. In this study, an antibacterial pADM with good performance was prepared by adding two natural products as modifiers, quercetin (QCT) and tea tree oil (TTO). The result of Fourier-transform infrared (FTIR) proved that the addition of modifiers did not break the natural triple-helical structure of collagen. Meanwhile, the results of differential scanning calorimetry (DSC), thermogravimetric analysis (TG), mechanic experiment, and enzymatic degradation demonstrated that pADM handled with QCT and TTO (termed QCT-TTO-pADM) had better thermal stability, mechanical strength, and resistance to enzymatic degradation than pADM. Meanwhile, QCT-TTO-pADM had excellent antibacterial activity and showed an antibacterial rate of over 80%. Furthermore, in the cytocompatibility analysis, QCT-TTO-pADM had no side effects on the adhesion, growth, and proliferation of fibroblasts. QCT-TTO-pADM could even accelerate wound healing more efficiently than pADM and glutaraldehyde-modified pADM (GA-pADM). In conclusion, QCT-TTO-pADM was a potential antibacterial wound dressing with good performance.

Factors affecting thermal stability of collagen from the aspects of extraction, processing and modification

Abstract

Collagen, as a thermal-sensitive protein, is the most abundant structural protein in animals. Native collagen has been widely applied in various fields due to its specific physicochemical and biological properties. The beneficial properties would disappear with the collapse of the unique triple helical structure during heating. Understanding thermal stability of collagen is of great significance for practical applications. Previous studies have shown the thermal stability would be affected by the different sources, extraction methods, solvent systems in vitro and modified methods. Accordingly, the factors affecting thermal stability of collagen are discussed in detail in this review.

Graphical abstract

Seaweed polysaccharide derived bioaldehyde nanocomposite: Potential application in anticancer therapeutics

In the present study, we have demonstrated synthesis of agar aldehyde (A_ald) from seaweed polysaccharide and its further successful application for preparation of A_ald mediated solid silver nanocomposite (A_ald-AgNPs). A_ald-AgNPs were characterized for biophysical properties by FTIR, XRD, SEM, TEM, XPS, and UV-vis spectroscopy. A_ald-AgNPs were further tested in vitro and in vivo for anticancer activity. The results of the in vitro study revealed that A_ald-AgNPs exhibited activity against 3 cancer cell lines. A_ald-AgNPs were found to act through causing dose dependent increase in cell size, inducing anueploidy, mitochondrial disintegration and increasing septa formation in cell cytoplasm. Results of in vivo anticancer activity against ME-180, Colon-26, and HL-60 xenograft mice tumor models showed 64 %, 27.3 % and 51 % reduction in tumor volume, respectively with 83-100 % survival rate. A_ald-AgNPs exhibited excellent antibacterial activity. It was interesting to note that A_ald-AgNPs did not exhibit any significant detrimental effect on viability and metabolic activity of normal bone marrow derived mesenchymal stem cells. This study opens new areas of research for chemists and biologists to use seaweed-derived polymers to develop nanocomposites for cancer therapeutics.

Three dimensional polyvinyl alcohol scaffolds modified with collagen for HepG2 cell culture

The creation of in vitro functional hepatic tissue simulating micro environmental niche of the native liver is a keen area of research due to its demand in bioartificial liver. However, it is still unclear how to maintain benign cell function while achieving the sufficient cell quantity. In this work, we aim to prepare a novel scaffold for the culture of HepG2 cells, a liver cell line, by modifying polyvinyl alcohol (PVA) scaffold with collagen (COL). PVA is a kind of synthetic biostable polymer with high hydrophilicity in the human body, has been widely used in the biomedical field. However, the use of PVA is limited in cell cultures due to lack of biologically active functional groups. In this study, amino silane (KH-550), glutaraldehyde and native type I collagen were used to modify three-dimensional PVA scaffold to establish a suitable composite scaffold for hepatocyte culture. Three types of composite scaffolds were prepared for different collagen content, named as PVA/COL (0.2%), PVA/COL (0.5%) and PVA/COL (0.8%), respectively. The composite scaffolds were characterized by SEM, XPS, FTIR, MS, porosity estimation and water contact angle measurement. The PVA/COL (0.8%) scaffolds had the highest collagen content of 12.13%. The composite scaffold showed high porosity with interconnected pores. Furthermore, the biocompatibility between HepG2 cells and scaffolds was evaluated by the ability of cell proliferation, albumin secretion, as well as urea synthesis. The coating of collagen on PVA scaffolds promoted hydrophilicity and HepG2 cell adhesion. Additionally, enhanced cell proliferation, increased albumin secretion and urea synthesis were observed in HepG2 cells growing on collagen-coated three-dimensional PVA scaffolds.

Preparation, Characterization, and Biological Testing of Novel Magnetic Nanocomposite Hydrogels

To provide a novel approach for the clinical treatment of cartilage tissue defects, we prepared a new type of magnetic nanocomposite hydrogel with an optimal raw material ratio using Fe3O4, polyvinyl alcohol (PVA), and type-II collagen (COLII). Briefly, five groups of PVA and collagen hydrogel matrices with different mass ratios were prepared by a combination of repeated thawing cycles and foam-frozen ice crystal separation methods. Microscopic characterization was conducted using electron microscopy, and the biomechanical properties of each group of hydrogels were then tested. The highest performing component hydrogel matrix was selected after which Fe3O4 with different mass ratios was introduced to construct a new Fe3O4/PVA/COLII hydrogel. The prepared composite hydrogels were also microscopically characterized using electron microscopy along with scanning, measurements for porosity and moisture content, and biomechanical, infrared spectrum and degradation performance testing. CCK-8 detection and staining to determine the amount of living and dead cells were also performed. Collectively, these results showed that PVA/COLII,95:5 was the optimal hydrogel matrix. Using this hydrogel matrix, five groups of composite hydrogels with different Fe3O4 mass ratios were then prepared. There was no significant difference in the microscopic characteristics between these different hydrogels. Fe3O4/PVA/COLII,5:95:5 had better physical properties as well as swelling performance and cell compatibility. The PVA/COLII,95:5 hydrogel matrix was determined to be the best, while the new magnetic nanocomposite hydrogel Fe3O4/PVA/COLII,5:95:5 had good, comprehensive properties.

Physico-Chemical Characterization and Biological Tests of Collagen/Silk Fibroin/Chitosan Scaffolds Cross-Linked by Dialdehyde Starch

In this study, three-dimensional (3D) biopolymeric scaffolds made from collagen, silk fibroin and chitosan were successfully prepared by the freeze drying method. Dialdehyde starch (DAS) was used as a cross-linking agent for the materials. The properties of the materials were studied using density and porosity measurements, scanning electron microscope (SEM) imaging, swelling and moisture content measurements. Additionally, cytocompatibility of the materials in contact with MG-63 osteoblast-like cells was tested by live/dead staining and resazurin reduction assay on days 1, 3 and 7. It was found that new 3D materials made from collagen/silk fibroin/chitosan binary or ternary mixtures are hydrophilic with a high swelling ability (swelling rate in the range of 1680–1900%). Cross-linking of such biopolymeric materials with DAS increased swelling rate up to about 2100%, reduced porosity from 96–97% to 91–93%, and also decreased density and moisture content of the materials. Interestingly, presence of DAS did not influence the microstructure of the scaffolds as compared to non-cross-linked samples as shown by SEM. All the tested samples were found to be cytocompatible and supported adhesion and growth of MG-63 cells as shown by live–dead staining and metabolic activity test.