Tunicate cellulose nanocrystals: Preparation, neat films and nanocomposite films with glucomannans

Bacterial cellulose nanocrystals obtained through enzymatic and acidic routes: A comparative study of their main properties and in vitro biological responses

Cellulose nanocrystals (CNCs) are crystalline domains isolated from cellulosic fibers. They have been utilized in a wide range of applications, such as reinforcing fillers, antibacterial agents and manufacturing of biosensors. Whitin this context, the aim of this work was to obtain and analyze CNCs extracted from bacterial nanocellulose (BNC) using two distinct methods combined with milling pre-treatment: an acidic hydrolysis using 64 % sulfuric acid and an enzymatic hydrolysis using a commercial cellulase enzyme mixture. The CNCs obtained from the enzymatic route (e-CNCs) were observed to be spherical nanoparticles with diameter of 56 ± 11 nm. In contrast, the CNCs from the acid hydrolysis (a-CNCs) appeared as needle-shaped nanoparticles with a high aspect ratio with lengths/widths of 158 ± 64 nm/11 ± 2 nm. The surface zeta potential (ZP) of the a-CNCs was -30,8 mV, whereas the e-CNCs has a potential of +2.70 ± 3.32 mV, indicating that a-CNCs consisted of negatively charged particles with higher stability in solution. Although the acidic route resulted in nanocrystals with a slightly higher crystallinity index compared to the enzymatic route, e-CNCs was found to be more thermally stable than BNC and a-CNCs. Here, we also confirmed the safety of a-CNCs and e-CNCs using L929 cell line. Lastly, this article describes two different CNCs synthesis approaches that leads to the formation of nanoparticles with different dimensions, morphology and unique physicochemical properties. To the best of our knowledge, this is the first study to yield spherical nanoparticles as a result of BNC enzymatic treatment.

Pickering nanoemulsion loaded with eugenol contributed to the improvement of konjac glucomannan film performance

Konjac glucomannan (KGM) is becoming a very potential food packaging material due to its good film-forming properties and stability. However, KGM film has several shortcomings such as low mechanical strength, strong water absorption, and poor self-antibacterial performance, which limits its application. Therefore, in order to enhance the mechanical and functional properties of KGM film, this study prepared Pickering nanoemulsion loaded with eugenol and added it to the KGM matrix to explore the improvement effect of Pickering nanoemulsion on KGM film properties. Compared to pure KGM film and eugenol directly added film, the mechanical strength of Pickering-KGM film was significantly improved due to the establishment of ample hydrogen bonding interactions between the β-cyclodextrin inclusion complex system and KGM. Pickering-KGM film had significant antioxidant capacity than pure KGM film and eugenol directly added KGM film (eugenol-KGM film) (~3.21 times better than KGM film, ~0.51 times better than eugenol-KGM film). In terms of antibacterial activity, Pickering-KGM film had good inhibitory effect on Escherichia coli, Staphylococcus aureus, and Candida albicans, and raspberry preservation experiment showed that the shelf life of the Pickering-KGM film could be extended to about 6 days. To sum up, this study developed a novel means to improve the film performance and provide a new insight for the development and application of food packaging film.

Recent Progress in Improving Rate Performance of Cellulose-Derived Carbon Materials for Sodium-Ion Batteries

Cellulose-derived carbon is regarded as one of the most promising candidates for high-performance anode materials in sodium-ion batteries; however, its poor rate performance at higher current density remains a challenge to achieve high power density sodium-ion batteries. The present review comprehensively elucidates the structural characteristics of cellulose-based materials and cellulose-derived carbon materials, explores the limitations in enhancing rate performance arising from ion diffusion and electronic transfer at the level of cellulose-derived carbon materials, and proposes corresponding strategies to improve rate performance targeted at various precursors of cellulose-based materials. This review also presents an update on recent progress in cellulose-based materials and cellulose-derived carbon materials, with particular focuses on their molecular, crystalline, and aggregation structures. Furthermore, the relationship between storage sodium and rate performance the carbon materials is elucidated through theoretical calculations and characterization analyses. Finally, future perspectives regarding challenges and opportunities in the research field of cellulose-derived carbon anodes are briefly highlighted.

Preparation and characterization of a novel high barrier mulching film with tunicate cellulose nanocrystals/sodium alginate/alkali lignin

In this study, the base film (CSL) was prepared by blending tunicate cellulose nanocrystals (TCNCs) extracted from tunicate shells, with sodium alginate (SA) and alkali lignin (AL). Then, the mulching film (CSL-WK) was prepared using water-borne polyurethane (WPU) as binder to install low-energy Kaolin on the surface of CSL film. The influences of composition with different concentrations on mechanical properties were studied. The tensile strength and elongation at break of CSL-WK film could reach 86.58 MPa and 50.49 %, respectively. The mulching films were characterized by degradability test, SEM, FTIR, and TGA. TCNCs had good compatibility with SA and AL, and a rough structure was formed on the surface of the film to improve the hydrophobicity. The barrier properties, including ultraviolet resistance, water contact angle, water vapor permeability, water retention, and flame retardancy, were tested. The results showed that CSL-WK films could block 97 % of ultraviolet light, reduce about 25 % of soil water loss, and self-extinguish within 7 s of open flame ignition. Note that the secondary spraying method significantly improved the barrier property of films. This study lays a foundation for the preparation of ecologically friendly, biodegradable, and high barrier mulching film, and expands the application of marine resources.

Nanocellulose: Structure, modification, biodegradation and applications in agriculture as slow/controlled release fertilizer, superabsorbent, and crop protection: A review

This review investigates the potential of nanocellulose in agriculture, encompassing its structure, synthesis, modification, and applications. Our investigation of the characteristics of nanocellulose includes a comprehensive classification of its structure. Various mechanical, chemical and enzymatic synthesis techniques are evaluated, each offering distinct possibilities. The central role of surface functionalization is thoroughly examined. In particular, we are evaluating the conventional production of nanocellulose, thus contributing to the novelty. This review is a pioneering effort to comprehensively explore the use of nanocellulose in slow and controlled release fertilizers, revolutionizing nutrient management and improving crop productivity with reduced environmental impact. Additionally, our work uniquely integrates diverse applications of nanocellulose in agriculture, ranging from slow-release fertilizers, superabsorbent cellulose hydrogels for drought stress mitigation, and long-lasting crop protection via nanocellulose-based seed coatings. The study ends by identifying challenges and unexplored opportunities in the use of nanocellulose in agriculture. This review makes an innovative contribution by being the first comprehensive study to examine the multiple applications of nanocellulose in agriculture, including slow-release and controlled-release fertilizers.

Multifunctional Poly(3,4-ethylenedioxythiophene)/Crystalline Nanofibrous Cellulose Composites for Eco-Friendly and Sustainable Electronics

Nanocellulose constitutes promising resources for next-generation electronics, particularly when incorporated with conductive polymers due to their abundance, renewability, processability, biodegradability, flexibility, and mechanical performance. In this study, electrically conducting cellulose nanofibers were fabricated through in situ chemical polymerization of poly(3,4-ethylenedioxythiophene) (PEDOT) on the surface of sulfuric acid-treated cellulose nanofibers (SACN). The utilization of highly crystalline SACN extracted from tunicate yielded synergistic effects in PEDOT polymerization for achieving a highly conductive and molecularly uniform coating. Polymerization parameters, such as monomer concentration, molar ratio with oxidants, and temperature, were systematically investigated. High electrical conductivity of up to 57.8 S cm-1 was obtained without utilizing the classical polystyrenesulfonate dopant. The resulting nanocomposite demonstrates the unique advantages of both electrically conductive PEDOT and mechanically robust high-crystalline cellulose nanofibers. As a proof-of-applicational concept, an electrical circuit was drawn with SACN-PEDOT as the conductive ink on flexible paper using a simple commercial extrusion-based printer. Furthermore, the flame-retardant property of SACN-PEDOT was demonstrated owing to the high crystallinity of SACN, effective char formation, and high conductivity of PEDOT. The multifunctional SACN-PEDOT developed in this study shows great promise to be employed in versatile applications as a low-cost, ecofriendly, flexible, and sustainable electrically conductive material.

Cellulose nanocrystals in the development of biodegradable materials: A review on CNC resources, modification, and their hybridization

The escalating demand for sustainable materials has propelled cellulose into the spotlight as a promising alternative to petroleum-based products. As the most abundant organic polymer on Earth, cellulose is ubiquitous, found in plants, bacteria, and even a unique marine animal-the tunicate. Cellulose polymers naturally give rise to microscale semi-crystalline fibers and nanoscale crystalline regions known as cellulose nanocrystals (CNCs). Exhibiting rod-like structures with widths spanning 3 to 50 nm and lengths ranging from 50 nm to several microns, CNC characteristics vary based on the cellulose source. The degree of crystallinity, crucial for CNC properties, fluctuates between 49 and 95 % depending on the source and synthesis method. CNCs, with their exceptional properties such as high aspect ratio, relatively low density (≈1.6 g cm-3), high axial elastic modulus (≈150 GPa), significant tensile strength, and birefringence, emerge as ideal candidates for biodegradable fillers in nanocomposites and functional materials. The percolation threshold, a mathematical concept defining long-range connectivity between filler and polymer, governs the effectiveness of reinforcement in nanocomposites. This threshold is intricately influenced by the aspect ratio and molecular interaction strength, impacting CNC performance in polymeric and pure nanocomposite materials. This comprehensive review explores diverse aspects of CNCs, encompassing their derivation from various sources, methods of modification (both physical and chemical), and hybridization with heterogeneous fillers. Special attention is devoted to the hybridization of CNCs derived from tunicates (TCNC) with those from wood (WCNC), leveraging the distinct advantages of each. The overarching objective is to demonstrate how this hybridization strategy mitigates the limitations of WCNC in composite materials, offering improved interaction and enhanced percolation. This, in turn, is anticipated to elevate the reinforcing effects and pave the way for the development of nanocomposites with tunable viscoelastic, physicochemical, and mechanical properties.

Exploring nanocellulose frontiers: A comprehensive review of its extraction, properties, and pioneering applications in the automotive and biomedical industries

Material is an inseparable entity for humans to serve different purposes. However, synthetic polymers represent a major category of anthropogenic pollutants with detrimental impacts on natural ecosystems. This escalating environmental issue is characterized by the accumulation of non-biodegradable plastic materials, which pose serious threats to the health of our planet's ecosystem. Cellulose is becoming a focal point for many researchers due to its high availability. It has been used to serve various purposes. Recent scientific advancements have unveiled innovative prospects for the utilization of nanocellulose within the area of advanced science. This comprehensive review investigates deeply into the field of nanocellulose, explaining the methodologies employed in separating nanocellulose from cellulose. It also explains upon two intricately examined applications that emphasize the pivotal role of nanocellulose in nanocomposites. The initial instance pertains to the automotive sector, encompassing cutting-edge applications in electric vehicle (EV) batteries, while the second exemplifies the use of nanocellulose in the field of biomedical applications like otorhinolaryngology, ophthalmology, and wound dressing. This review aims to provide comprehensive information starting from the definitions, identifying the sources of the nanocellulose and its extraction, and ending with the recent applications in the emerging field such as energy storage and biomedical applications.

Nanocellulose: A comprehensive review investigating its potential as an innovative material for water remediation

Rapid growth in industrialization sectors, the wastewater treatment plants become exhausted and potentially not able to give desirable discharge standards. Many industries discharge the untreated effluent into the water bodies which affects the aquatic diversity and human health. The effective disposal of industrial effluents thus has been an imperative requirement. For decades nanocellulose based materials gained immense attraction towards application in wastewater remediation and emerged out as a new biobased nanomaterial. It is light weighted, cost effective, mechanically strong and easily available. Large surface area, versatile surface functionality, biodegradability, high aspect ratio etc., make them suitable candidate in this field. Majorly cellulose based nanomaterials are used in the form of cellulose nanocrystals (CNCs), cellulose nanofibers (CNFs), or bacterial nanocellulose (BNC). This review specifically describes about a variety of extraction methods to produced nanocellulose and also discusses the modification of nanocellulose by adding functionalities in its surface chemistry. We majorly focus on the utilization of nanocellulose based materials in water remediation for the removal of different contaminants such as dyes, heavy metals, oil, microbial colony etc. This review mainly emphasizes in ray of hope towards nanocellulose materials to achieve more advancement in the water remediation fields.

Phytochemical Analysis of Anacamptis coriophora Plant Cultivated Using Ex Vitro Symbiotic Propagation

This study aims to investigate the functional groups and phytochemical profile of Anacamptis coriophora seeds, tubers, and flowers. Symbiotic seedlings produced using the ex vitro method were transferred to their natural habitat and grown to analyze the functional groups and phytochemical profiles of tubers and flowers. The life cycles of the transferred seedlings were monitored, and tubers and flowers were harvested for analysis. ATR-FTIR spectroscopy revealed the presence of functional groups such as polysaccharides, lignin, and proteins in both tubers and flowers. Differences in spectral frequencies between first-year and second-year tubers were observed. Fatty acid analysis identified 30 different compounds in seeds, flowers, and tubers, with linoleic acid being the most abundant (27 % in seeds, 33 % in tubers), and palmitic acid present in flowers (24 %). GC-MS analysis of ethanol extracts from these components highlighted the presence of 32 compounds, including hydroxyacetic acid, hydrazide, cytidine (Z)-7-hexadecenal, 2,2-dimethoxyethane, 2,5,6-trimethyldecane, and butanamide, 4-amino-N-hydroxy. A. coriophora's tubers, flowers, and seeds may contain active metabolites with therapeutic potential. These results are valuable for the commercial cultivation of the plant.

Tunicates as Sources of High-Quality Nutrients and Bioactive Compounds for Food/Feed and Pharmaceutical Applications: A Review

Tunicates are widely distributed worldwide and are recognized as abundant marine bioresources with many potential applications. In this review, state-of-the-art studies on chemical composition analyses of various tunicate species were summarized; these studies confirmed that tunicates contain nutrients similar to fish (such as abundant cellulose, protein, and ω-3 fatty acid (FA)-rich lipids), indicating their practical and feasible uses for food or animal feed exploration. However, the presence of certain toxic elements should be evaluated in terms of safety. Moreover, recent studies on bioactive substances extracted from tunicates (such as toxins, sphingomyelins, and tunichromes) were analyzed, and their biological properties were comprehensively reviewed, including antimicrobial, anticancer, antioxidant, antidiabetic, and anti-inflammatory activities. In addition, some insights and prospects for the future exploration of tunicates are provided which are expected to guide their further application in the food, animal feed, and pharmaceutical industries. This review is critical to providing a new pathway for converting the common pollution issues of hydroponic nutrients into valuable marine bioresources.

Insight into the Latest Medical Applications of Nanocellulose

Nanocelluloses (NCs) are appealing nanomaterials that have experienced rapid development in recent years, with great potential in the biomedical field. This trend aligns with the increasing demand for sustainable materials, which will contribute both to an improvement in wellbeing and an extension of human life, and with the demand to keep up with advances in medical technology. In recent years, due to the diversity of their physical and biological properties and the possibility of tuning them according to the desired goal, these nanomaterials represent a point of maximum interest in the medical field. Applications such as tissue engineering, drug delivery, wound dressing, medical implants or those in cardiovascular health are some of the applications in which NCs have been successfully used. This review presents insight into the latest medical applications of NCs, in the forms of cellulose nanocrystals (CNCs), cellulose nanofibers (CNFs) and bacterial nanocellulose (BNC), with an emphasis on the domains that have recently experienced remarkable growth, namely wound dressing, tissue engineering and drug delivery. In order to highlight only the most recent achievements, the presented information is focused on studies from the last 3 years. Approaches to the preparation of NCs are discussed either by top-down (chemical or mechanical degradation) or by bottom-up (biosynthesis) techniques, along with their morphological characterization and unique properties, such as mechanical and biological properties. Finally, the main challenges, limitations and future research directions of NCs are identified in a sustained effort to identify their effective use in biomedical fields.

All-Tunicate Cellulose Film with Good Light Management Properties for High-Efficiency Organic Solar Cells

Tunicate nanocellulose with its unique properties, such as excellent mechanical strength, high crystallinity, and good biodegradability, has potential to be used for the preparation of light management film with tunable transmittance and haze. Herein, we prepared a whole tunicate cellulose film with tunable haze levels, by mixing tunicate microfibrillated cellulose (MFC) and tunicate cellulose nanofibrils (CNF). Then, the obtained whole tunicate cellulose film with updated light management was used to modify the organic solar cell (OSC) substrate, aiming to improve the light utilization efficiency of OSC. Results showed that the dosage of MFC based on the weight of CNF was an important factor to adjust the haze and light transmittance of the prepared cellulose film. When the dosage of MFC was 3 wt.%, the haze of the obtained film increased 74.2% compared to the pure CNF film (39.2%). Moreover, the optimized tunicate cellulose film exhibited excellent mechanical properties (e.g., tensile strength of 168 MPa, toughness of 5.7 MJ/m³) and high thermal stability, which will be beneficial to the workability and durability of OSC. More interestingly, we applied the obtained whole tunicate cellulose film with a high haze (68.3%) and high light transmittance (85.0%) as an additional layer to be adhered to the glass substrate of OSC, and a notable improvement (6.5%) of the power conversion efficiency was achieved. With the use of biodegradable tunicate cellulose, this work provides a simple strategy to enhance light management of the transparent substrate of OSC for improving power conversion efficiency.

Influence of preparation techniques of cellulose II nanocrystals as reinforcement for tannery solid waste-based gelatin composite films

Tannery waste-based gelatin composite film reinforced with cellulose II nanocrystal (CNC II) extracted from wet wipes using three different hydrolysis techniques is explored for its functional properties and possible utilization as a biodegradable packaging material. CNC II isolated using hydrogen peroxide (PCNC), citric acid (CCNC), and hydrochloric acid (HCNC) differed in morphological and crystalline character as investigated using DLS, FE-SEM, FTIR, and XRD analysis. The crystallinity of PCNC, CCNC, and HCNC was found to be 81.1%, 75.4%, and 86.1%, respectively. The highly crystalline CNC II (PCNC) incorporation improved mechanical stiffness of rawhide trimming waste-based gelatin films by 50% compared to control gelatin film. Maximum thermal decomposition with Tmax of 329 °C was obtained for gelatin films with PCNC nano-reinforcement. Films with CNC II were structurally stable and sufficiently antibacterial against Gram-positive S. aureus microbial strain. Strong interfacial non-covalent and hydrogen bonding interactions between gelatin and cellulose II nanocrystal have likely enhanced the properties of the composite films. Incorporation of CNC II reduced the surface wettability of the films and nanocomposites absorbed UV radiation as evidenced by transmittance value T280 of 0.19%. Nanocomposite films degraded up to 79.9% of initial mass within 7 days of soil burial. Furthermore, based on the optimized system, single-use packaging application of eggplant seeds has been demonstrated.

Recent Progress on Tailoring the Biomass-Derived Cellulose Hybrid Composite Photocatalysts

Biomass-derived cellulose hybrid composite materials are promising for application in the field of photocatalysis due to their excellent properties. The excellent properties between biomass-derived cellulose and photocatalyst materials was induced by biocompatibility and high hydrophilicity of the cellulose components. Biomass-derived cellulose exhibited huge amount of electron-rich hydroxyl group which could promote superior interaction with the photocatalyst. Hence, the original sources and types of cellulose, synthesizing methods, and fabrication cellulose composites together with applications are reviewed in this paper. Different types of biomasses such as biochar, activated carbon (AC), cellulose, chitosan, and chitin were discussed. Cellulose is categorized as plant cellulose, bacterial cellulose, algae cellulose, and tunicate cellulose. The extraction and purification steps of cellulose were explained in detail. Next, the common photocatalyst nanomaterials including titanium dioxide (TiO2), zinc oxide (ZnO), graphitic carbon nitride (g-C3N4), and graphene, were introduced based on their distinct structures, advantages, and limitations in water treatment applications. The synthesizing method of TiO2-based photocatalyst includes hydrothermal synthesis, sol-gel synthesis, and chemical vapor deposition synthesis. Different synthesizing methods contribute toward different TiO2 forms in terms of structural phases and surface morphology. The fabrication and performance of cellulose composite catalysts give readers a better understanding of the incorporation of cellulose in the development of sustainable and robust photocatalysts. The modifications including metal doping, non-metal doping, and metal-organic frameworks (MOFs) showed improvements on the degradation performance of cellulose composite catalysts. The information and evidence on the fabrication techniques of biomass-derived cellulose hybrid photocatalyst and its recent application in the field of water treatment were reviewed thoroughly in this review paper.

Emerging Food Packaging Applications of Cellulose Nanocomposites: A Review

Cellulose is the most abundant biopolymer on Earth, which is synthesized by plants, bacteria, and animals, with source-dependent properties. Cellulose containing β-1,4-linked D-glucoses further assembles into hierarchical structures in microfibrils, which can be processed to nanocellulose with length or width in the nanoscale after a variety of pretreatments including enzymatic hydrolysis, TEMPO-oxidation, and carboxymethylation. Nanocellulose can be mainly categorized into cellulose nanocrystal (CNC) produced by acid hydrolysis, cellulose nanofibrils (CNF) prepared by refining, homogenization, microfluidization, sonification, ball milling, and the aqueous counter collision (ACC) method, and bacterial cellulose (BC) biosynthesized by the Acetobacter species. Due to nontoxicity, good biodegradability and biocompatibility, high aspect ratio, low thermal expansion coefficient, excellent mechanical strength, and unique optical properties, nanocellulose is utilized to develop various cellulose nanocomposites through solution casting, Layer-by-Layer (LBL) assembly, extrusion, coating, gel-forming, spray drying, electrostatic spinning, adsorption, nanoemulsion, and other techniques, and has been widely used as food packaging material with excellent barrier and mechanical properties, antibacterial activity, and stimuli-responsive performance to improve the food quality and shelf life. Under the driving force of the increasing green food packaging market, nanocellulose production has gradually developed from lab-scale to pilot- or even industrial-scale, mainly in Europe, Africa, and Asia, though developing cost-effective preparation techniques and precisely tuning the physicochemical properties are key to the commercialization. We expect this review to summarise the recent literature in the nanocellulose-based food packaging field and provide the readers with the state-of-the-art of this research area.

Biomaterial and biocompatibility evaluation of tunicate nanocellulose for tissue engineering

Extracellular matrix fibril components, such as collagen, are crucial for the structural properties of several tissues and organs. Tunicate-derived cellulose nanofibrils (TNC) combined with living cells could become the next gold standard for cartilage and soft-tissue repair, as TNC fibrils present similar dimensions to collagen, feasible industrial production, and chemically straightforward and cost-efficient extraction procedures. In this study, we characterized the physical properties of TNC derived from aquaculture production in Norwegian fjords and evaluated its biocompatibility regarding induction of an inflammatory response and foreign-body reactions in a Wistar rat model. Additionally, histologic and immunohistochemical analyses were performed for comparison with expanded polytetrafluoroethylene (ePTFE) as a control. The average length of the TNC as determined by atomic force microscopy was tunable from 3 μm to 2.4 μm via selection of a various number of passages through a microfluidizer, and rheologic analysis showed that the TNC hydrogels were highly shear-thinning and with a viscosity dependent on fibril length and concentration. As a bioink, TNC exhibited excellent rheological and printability properties, with constructs capable of being printed with high resolution and fidelity. We found that post-print cross-linking with alginate stabilized the construct shape and texture, which increased its ease of handling during surgery. Moreover, after 30 days in vivo, the constructs showed a highly-preserved shape and fidelity of the grid holes, with these characteristics preserved after 90 days and with no signs of necrosis, infection, acute inflammation, invasion of neutrophil granulocytes, or extensive fibrosis. Furthermore, we observed a moderate foreign-body reaction involving macrophages, lymphocytes, and giant cells in both the TNC constructs and PTFE controls, although TNC was considered a non-irritant biomaterial according to ISO 10993-6 as compared with ePTFE. These findings represent a milestone for future clinical application of TNC scaffolds for tissue repair. One sentence summary: In this study, the mechanical properties of tunicate nanocellulose are superior to nanocellulose extracted from other sources, and the biocompatibility is comparable to that of ePTFE.

Divergent growth of poly(amidoamine) dendrimer-like branched polymers at the reducing end of cellulose nanocrystals

This paper presents the growth of dendritic polymers at the reducing ends of cellulose nanocrystals by the "grafting from" approach. We took advantage of the chemically differentiated ends of cellulose nanocrystals to specifically synthesize dendrimers at their reducing end by the divergent approach. We used acid-amine coupling reactions in aqueous media to synthesize the carboxylic acid- or amine-terminated poly(amidoamine) dendrimers. The growth of dendrimer generations was monitored by UV and FTIR spectroscopies, and we successfully introduced up to 4 generations. The dendrimer growth at reducing ends was demonstrated by the nanocrystal adsorption driven by the peripheral amino groups onto gold surfaces. Hence, the results from quartz crystal microbalance with dissipation (QCM-D) pointed to a rather upright orientation of the dendrimer-modified cellulose nanocrystals. As the generation increased, the adsorbed layers appeared to be more flexible, which demonstrated that the functionality at the reducing end can successfully tune the properties of cellulose nanocrystals.

Mechanically Reinforced, Flexible, Hydrophobic and UV Impermeable Starch-Cellulose Nanofibers (CNF)-Lignin Composites with Good Barrier and Thermal Properties

Bio-based composite films have been widely studied as potential substitutes for conventional plastics in food packaging. The aim of this study was to develop multifunctional composite films by introducing cellulose nanofibers (CNF) and lignin into starch-based films. Instead of costly and complicated chemical modification or covalent coupling, this study optimized the performance of the composite films by simply tuning the formulation. We found that starch films were mechanically reinforced by CNF, with lignin dispersing as nanoparticles embedded in the matrix. The newly built-up hydrogen bonding between these three components improves the integration of the films, while the introduction of CNF and lignin improved the thermal stability of the starch-based films. Lignin, as a functional additive, improved hydrophobicity and blocked UV transmission. The inherent barrier property of CNF and the dense starch matrix provided the composite films with good gas barrier properties. The prepared flexible films were optically transparent, and exhibited UV blocking ability, good oxygen-barrier properties, high hydrophobicity, appreciable mechanical strength and good thermal stability. These characteristics indicate potential utilization as a green alternative to synthetic plastics especially for food packaging applications.

Mechanical properties of cellulose nanofibril papers and their bionanocomposites: A review

Cellulose nanofibril (CNF) paper has various applications due to its unique advantages. Herein, we present the intrinsic mechanical properties of CNF papers, along with the preparation and properties of nanoparticle-reinforced CNF composite papers. The literature on CNF papers reveals a strong correlation between the intrafibrillar network structure and the resulting mechanical properties. This correlation is found to hold for all primary factors affecting mechanical properties, indicating that the performance of CNF materials depends directly on and can be tailored by controlling the intrafibrillar network of the system. The parameters that influence the mechanical properties of CNF papers were critically reviewed. Moreover, the effect on the mechanical properties by adding nanofillers to CNF papers to produce multifunctional composite products was discussed. We concluded this article with future perspectives and possible developments in CNFs and their bionanocomposite papers.

The comparison of the properties of nanocellulose isolated from colonial and solitary marine tunicates

This is the first comparative of tunicate cellulose nanocrystalline (t-CNC) from colonial and solitary tunicates. The t-CNC from the colonial tunicate Eudistoma sp. (CL1) was compared with solitary tunicates Polycarpa reniformis (CL2) and Phallusia nigra (CL3). Tunicate samples were extracted by methanol. Residues from the methanol extraction were then subjected to further cellulose purification using pre-hydrolysis, kraft-cooking, bleaching, and sulfuric acid hydrolysis to yield t-CNC. The solitary tunicates yielded higher microfibril contents after the bleaching step but obtained similar t-CNC content to the colonial one after acid hydrolysis. The isolated t-CNC were characterized using Fourier transform infrared spectroscopy, X-ray diffraction, thermalgravimetric analysis, and transmission electron microscopy. Both colonial and solitary tunicates yielded cellulose type I. The pure cellulose type I was successfully isolated from solitary tunicates whereas high inorganic impurities were observed in colonial tunicates. The isolate t-CNC showed high aspect ratios. The solitary and colonial tunicates provided t-CNC with crystallinity indexes over 97% and 35%, respectively. The crystalline size of t-CNCs ranged from 55-124 Å. The thermal stability of all isolated t-CNC was slightly decreased due to the sulfate functional groups gained after acid hydrolysis. We concluded that solitary tunicates were better than colonial tunicates as a source of t-CNC preparation.

Vascularization of tissue engineered cartilage - Sequential in vivo MRI display functional blood circulation

Establishing functional circulation in bioengineered tissue after implantation is vital for the delivery of oxygen and nutrients to the cells. Native cartilage is avascular and thrives on diffusion, which in turn depends on proximity to circulation. Here, we investigate whether a gridded three-dimensional (3D) bioprinted construct would allow ingrowth of blood vessels and thus prove a functional concept for vascularization of bioengineered tissue. Twenty 10 × 10 × 3-mm 3Dbioprinted nanocellulose constructs containing human nasal chondrocytes or cell-free controls were subcutaneously implanted in 20 nude mice. Over the next 3 months, the mice were sequentially imaged with a 7 T small-animal MRI system, and the diffusion and perfusion parameters were analyzed. The chondrocytes survived and proliferated, and the shape of the constructs was well preserved. The diffusion coefficient was high and well preserved over time. The perfusion and diffusion patterns shown by MRI suggested that blood vessels develop over time in the 3D bioprinted constructs; the vessels were confirmed by histology and immunohistochemistry. We conclude that 3D bioprinted tissue with a gridded structure allows ingrowth of blood vessels and has the potential to be vascularized from the host. This is an essential step to take bioengineered tissue from the bench to clinical practice.

Why Cellulose-Based Electrochemical Energy Storage Devices?

Recent findings demonstrate that cellulose, a highly abundant, versatile, sustainable, and inexpensive material, can be used in the preparation of very stable and flexible electrochemical energy storage devices with high energy and power densities by using electrodes with high mass loadings, composed of conducting composites with high surface areas and thin layers of electroactive material, as well as cellulose-based current collectors and functional separators. Close attention should, however, be paid to the properties of the cellulose (e.g., porosity, pore distribution, pore-size distribution, and crystallinity). The manufacturing of cellulose-based electrodes and all-cellulose devices is also well-suited for large-scale production since it can be made using straightforward filtration-based techniques or paper-making approaches, as well as utilizing various printing techniques. Herein, the recent development and possibilities associated with the use of cellulose are discussed, regarding the manufacturing of electrochemical energy storage devices comprising electrodes with high energy and power densities and lightweight current collectors and functional separators.

Overview of Nanocellulose in Food Packaging

BACKGROUND

The rising concern with environmental preservation has led to increasing interest in biodegradable polymer composites from renewable sources, such as cellulose and its derivatives. The use of nanocellulose is an innovative food packaging trend.

DISCUSSION

This paper presents an overview and discusses the state of the art of different nanocellulose materials used in food and food packaging, and identifies important patents related to them. It is important to consider that before marketing, new products must be proven safe for consumers and the environment.

CONCLUSION

Several packaging materials using nanocellulose have been developed and shown to be promising for use as active and intelligent materials for food packaging. Other nanocellulose products are under investigation for packaging and may enter the market in the near future. Many countries have been adjusting their regulatory frameworks to deal with nanotechnologies, including nanocellulose packaging.

Environmentally dependent adsorption of 2,4-dichlorophenol on cellulose-chitosan self-assembled composites

With the increasing need for bio-based materials developed by environmentally friendly procedures, this work shows a green method to develop shape-controlled structures from cellulose dissolving pulp coated by chitosan. This material was then tested to adsorb a common and widespread pollutant, 2,4-dichlorophenol under different pH conditions (5.5 and 9). Herein it was noticed that the adsorption only occurred in acidic pH (5.5) where electrostatic interaction drove the adsorption, demonstrating the potential to tune the response under desired conditions only. The adsorption was successful in the hydrogel structure with an adsorption capacity of 905 ± 71 mg/g from a solution with 16.6 ppm; furthermore, adsorption was also possible with dried hydrogel structures, presenting a maximum of adsorption of 646 ± 50 mg/g in a similar 16.6 ppm solution. Finally, adsorbent regeneration was successfully tested for both, dry (rewetted) and never-dried states, showing improved adsorption after regeneration in the case of the never dried hydrogel structures.

Using Cellulose Nanocrystal as Adjuvant to Improve the Dispersion Ability of Multilayer Graphene in Aqueous Suspension

Cellulose nanocrystal (CNC) has been applied in various fields due to its nano-structure, high aspect ratio, specific surface area and modulus, and abundance of hydroxy groups. In this work, CNC suspensions with different concentrations (0.4, 0.6, and 0.8%) were used as the adjuvant to improve the dispersion ability of multilayer graphene (MLG) in aqueous suspension, which is easy to be aggregated by van der Waals force between layers. In addition, N-methyl-2-pyrrolidone, ethanol, and ultrapure water were used as control groups. Zeta potential analysis and Fourier transform infrared spectroscopy showed that the stability of MLG/CNC has met the requirement, and the combination of CNC and MLG was stable in aqueous suspension. Results from transmission electron microscopy, Fourier transform infrared spectroscopy, and absorbance showed that MLG had a better dispersion performance in CNC suspensions, compared to the other solutions. Raman spectrum analysis showed that the mixtures of 1.0 wt% MLG with 0.4% CNC had the least defects and fewer layers of MLG. In addition, it is found that CNC suspension with 0.8% concentration showed the highest ability to disperse 1.0 wt% MLG with the most stable performance in suspension. Overall, this work proved the potential application of CNC as adjuvant in the field of graphene nanomaterials.

Study on the Anti-Biodegradation Property of Tunicate Cellulose

Tunicate is a kind of marine animal, and its outer sheath consists of almost pure Iβ crystalline cellulose. Due to its high aspect ratio, tunicate cellulose has excellent physical properties. It draws extensive attention in the construction of robust functional materials. However, there is little research on its biological activity. In this study, cellulose enzymatic hydrolysis was conducted on tunicate cellulose. During the hydrolysis, the crystalline behaviors, i.e., crystallinity index (CrI), crystalline size and degree of polymerization (DP), were analyzed on the tunicate cellulose. As comparisons, similar hydrolyses were performed on cellulose samples with relatively low CrI, namely α-cellulose and amorphous cellulose. The results showed that the CrI of tunicate cellulose and α-cellulose was 93.9% and 70.9%, respectively; and after 96 h of hydrolysis, the crystallinity, crystalline size and DP remained constant on the tunicate cellulose, and the cellulose conversion rate was below 7.8%. While the crystalline structure of α-cellulose was significantly damaged and the cellulose conversion rate exceeded 83.8% at the end of 72 h hydrolysis, the amorphous cellulose was completely converted to glucose after 7 h hydrolysis, and the DP decreased about 27.9%. In addition, tunicate cellulose has high anti-mold abilities, owing to its highly crystalized Iβ lattice. It can be concluded that tunicate cellulose has significant resistance to enzymatic hydrolysis and could be potentially applied as anti-biodegradation materials.

High crystallinity of tunicate cellulose nanofibers for high-performance engineering films

Tunicate cellulose nanofibers (CNFs) have received widespread attention as renewable and eco-friendly engineering materials because of their high crystallinity and mechanical stiffness. Here, we report the effects of disintegration process conditions on structure-property relationships of tunicate CNFs. By varying the hydrolysis time, we could establish a correlation between crystallinity of the CNFs with linearity and stiffness, which produces different molecular ordering within their nanostructured films. Despite having identical raw materials, tensile strength and thermal conductivity of the resulting layered films varied widely, ranging from 95.6 to 205 MPa and from 1.08 to 2.37 W/mK respectively. Furthermore, nanolayered CNF films provided highly anisotropic thermal conductivities with an in- and through-plane ratio of 21.5. Our systematic investigations will provide general and practical strategies in tailoring material properties for emerging engineering applications, including flexible paper electronics, heat sink adhesives and biodegradable, implantable devices.

Towards the scalable isolation of cellulose nanocrystals from tunicates

In order for sustainable nanomaterials such as cellulose nanocrystals (CNCs) to be utilized in industrial applications, a large-scale production capacity for CNCs must exist. Currently the only CNCs available commercially in kilogram scale are obtained from wood pulp (W-CNCs). Scaling the production capacity of W-CNCs isolation has led to their use in broader applications and captured the interest of researchers, industries and governments alike. Another source of CNCs with potential for commercial scale production are tunicates, a species of marine animal. Tunicate derived CNCs (T-CNCs) are a high aspect ratio CNC, which can complement commercially available W-CNCs in the growing global CNC market. Herein we report the isolation and characterization of T-CNCs from the tunicate Styela clava, an invasive species currently causing significant harm to local aquaculture communities. The reported procedure utilizes scalable CNC processing techniques and is based on our experiences from laboratory scale T-CNC isolation and pilot scale W-CNC isolation. To our best knowledge, this study represents the largest scale where T-CNCs have been isolated from any tunicate species, under any reaction conditions. Demonstrating a significant step towards commercial scale isolation of T-CNCs, and offering a potential solution to the numerous challenges which invasive tunicates pose to global aquaculture communities.

Engineered Multilayer Microcapsules Based on Polysaccharides Nanomaterials

The preparation of microcapsules composed by natural materials have received great attention, as they represent promising systems for the fabrication of micro-containers for controlled loading and release of active compounds, and for other applications. Using polysaccharides as the main materials is receiving increasing interest, as they constitute the main components of the plant cell wall, which represent an ideal platform to mimic for creating biocompatible systems with specific responsive properties. Several researchers have recently described methods for the preparation of microcapsules with various sizes and properties using cell wall polysaccharide nanomaterials. Researchers have focused mostly in using cellulose nanomaterials as structural components in a bio-mimetic approach, as cellulose constitutes the main structural component of the plant cell wall. In this review, we describe the microcapsules systems presented in the literature, focusing on the works where polysaccharide nanomaterials were used as the main structural components. We present the methods and the principles behind the preparation of these systems, and the interactions involved in stabilizing the structures. We show the specific and stimuli-responsive properties of the reported microcapsules, and we describe how these characteristics can be exploited for specific applications.

Unique and outstanding quantum dots (QD)/tunicate cellulose nanofibrils (TCNF) nanohybrid platform material for use as 1D ink and 2D film

Quantum dots (QD)/polymer materials have wide applications in biological imaging, clinical diagnostics, anti-counterfeiting materials, light-emitting devices and solar cells. The development of QD/cellulose nanofibrils (CNF) hybrids with a more perfect structure and excellent properties is important for improving known applications. A unique tunicate CNF (TCNF) was homogeneously blended with outstanding CdSe/CdS core/shell QD to prepare a novel QD/TCNF hybrid. The QD were monodispersed on a single TCNF fibril surface as an evenly distributed monolayer with an extremely high packing density and no visible aggregation. The prepared hybrid is an excellent platform nanomaterial which was demonstrated by its good writing fidelity when applied as a 1D ink and by its good processability in the preparation of 2D films with acceptable transparency and flexibility. This one-step direct blending approach provides a facile shortcut to effectively fabricate cellulose-based high-performance functional QD nanomaterials at the single-fibril level.

Co-assembling Polysaccharide Nanocrystals and Nanofibers for Robust Chiral Iridescent Films

Assembling robust chiral biopolymer structures without compromising vivid optical iridescence is a grand challenge for biocomposite materials. Herein, we report a hierarchical nanocellulose nanostructure with a helicoidal organization co-assembled from chiral rigid cellulose nanocrystals (CNCs) and longer nanofibers isolated from the hydrolyzed wood pulp. This resulting highly iridescent chiral nanocellulose material is much tougher than traditional chiral CNC films. We found that the mixed nanocellulose are composed of needle-like nanocrystals and very long (up to 800 nm) flexible cellulose nanofibers (CNFs). Large-scale molecular simulation indicates that enhanced dynamic hydrogen bonding with labile networking facilitates mechanical reinforcement, owing to increased nanocrystal length, the co-assembly of nanofibrils in mixed bundles, and interchain entanglements. This study provides a novel strategy to transform the wood pulp residues into high-value-added photonic-bound polysaccharide materials. These hierarchical biomaterials can overcome the conflicting trends in designing balanced mechanical and optical performance of chiral biofilms and their conversion to robust chiral photonic materials with enhanced performance.

Self-assembly properties of carboxylated tunicate cellulose nanocrystals prepared by ammonium persulfate oxidation and subsequent ultrasonication

Tunicate cellulose, extracted from the marine animal, has drawn increasing attention as the high crystallinity and aspect ratio. However, it is hard to prepare tunicate cellulose nanocrystals (tCNCs) with narrow size distribution in the traditional way, especially for the carboxylated samples, which also affects their lyotropic liquid crystal behavior to a certain extent. Herein, carboxylated tCNCs with uniform nanoscale dimensions and high surface charges density were prepared through ammonium persulfate (APS) oxidation and ultrasonic post-processing. Of particular interest, the formation of carboxylated tCNCs lyotropic chiral nematic liquid crystals was observed for the first time, which displayed obvious birefringence and fingerprint texture. Meanwhile, it was found that the critical concentration of phase separation for tCNCs suspension was around 3.5 wt% from the phase diagram. This study provides an efficient way to fabricate carboxylated tCNCs, and the self-assembly properties may lead to great potential applications in constructing advanced functional materials.

Effect of Ionic Surfactants on the Viscoelastic Properties of Chiral Nematic Cellulose Nanocrystal Suspensions

The gelation of cellulose nanocrystal (CNC) suspensions is explored in the presence of two ionic surfactants, namely, sodium dodecyl sulfate (SDS) with a negatively charged head and cetyltrimethylammonium bromide (CTAB) with a positively charged head. The viscosity profile of pure CNC suspensions indicated that at concentrations greater than 5 wt %, they exhibit gel-like behavior, where the viscosity shows a single shear-thinning profile. However, at concentrations lower than 1 wt %, the suspension shows isotropic behavior and experiences a transition to chiral nematic biphasic domains at increasing CNC concentration. In addition, the effect of CTAB, SDS, and NaCl on the surface charge of CNCs is analyzed and coupled with rheological measurements in order to study the relative importance of surfactants and ionic strength on the viscoelastic properties of the CNC suspensions. The mechanism of CNC/surfactants and CNC/CNC interactions leading to the gelation of CNC suspensions is also investigated. It was found that the addition of both ionic surfactants results in the gelation of biphasic chiral nematic CNC suspensions by fostering cross-linking between individual CNCs at smaller concentrations. In the case of CTAB, a gradual and ongoing increase in the viscoelastic moduli was observed with the increase of surfactant concentration, implying the induction of dominant attractive forces between CNCs by surfactant molecules. However, the presence of SDS stimulates both attractive and repulsive forces whose relative dominance controls the viscoelastic properties and gelation.

FTIR-based comparative analysis of glucomannan contents in some tuberous orchids, and effects of pre-processing on glucomannan measurement

BACKGROUND

Glucomannan (GM) is a polysaccharide of the mannan family of compounds found in some plant species. The dried and powdered tubers of some orchid species, collectively known as 'salep powder,' are a commercially important crop for human consumption and are one of the primary sources of GM. GM content is the primary indicator for the yield and quality of salep powder. We hypothesized that it would be more practical and accurate to measure GM content within tuber powder directly, prior to any purification or pre-processing. The GM content of tubers of 14 different orchid species was evaluated and compared using Fourier transform infrared (FTIR) spectroscopy and an enzymatic colorimetric method.

RESULTS

Among the analyzed modes, the sum of the peak areas at 873 and 812 cm^-1 , which represent the CH bending attributed to the β-pyranose form of d-glucose and d-mannose, respectively, gave the only confirmation using colorimetric methods. It was found that the tubers of Himantoglossum caprinum and Serapias vomeracea had the highest GM concentrations among the analyzed species. After conducting different pre-processing steps on Serapias vomeracea tubers, it was found that treating the tubers with milk, or high temperature resulted in an apparent increase in GM concentrations.

CONCLUSION

Himantoglossum caprinum and Serapias vomeracea give the highest yields of GM and should be used for commercial horticulture. GM estimation should be made prior to any pre-processing. FTIR spectroscopy is effective and reliable for directly comparing GM content of different orchid species, without the need for any purification or pre-processing. © 2019 Society of Chemical Industry.

The Impact of Lignin Structural Diversity on Performance of Cellulose Nanofiber (CNF)-Starch Composite Films

Lignin fractions having different molecular weights and varied chemical structures isolated from kraft lignins of both softwood and hardwood via a sequential solvent fractionation technique were incorporated into a tunicate cellulose nanofibers (CNF)—starch mixture to prepare 100% bio-based composite films. The aim was to investigate the impact of lignin structural diversity on film performance. It was confirmed that lignin’s distribution in the films was dependent on the polarity of solvents used for fractionation (acetone > methanol > ethanol > ethyl acetate) and influenced the optical properties of the films. The –OH group content and molecular weight of lignin were positively related to film density. In general, the addition of lignin fractions led to decrease in thermal stability and increase in Young’s modulus of the composite films. The modulus of the films was found to decrease as the molecular weight of lignin increased, and a higher amount of carboxyl and phenolic –OH groups in the lignin fraction resulted in films with higher stiffness. The thermal analysis showed higher char content formation for lignin-containing films in a nitrogen atmosphere with increased molecular weight. In an oxygen atmosphere, the phenol content, saturated side chains and short chain structures of lignin had impacts on the maximum decomposition temperature of the films, confirming the relationship between the chemical structure of lignin and thermo-oxidative stability of the corresponding film. This study addresses the importance of lignin diversities on composite film performance, which could be helpful for tailoring lignin’s applications in bio-based materials based on their specific characteristics.

Preparation and properties of cellulose nanocrystals, gelatin, hyaluronic acid composite hydrogel as wound dressing

Gelatin (GA), hyaluronic acid (HA) and cellulose nanocrystals (CNC) are promising materials for skin wound care. In this study the GA-HA-CNC hydrogels were prepared by cross-linking and freeze-drying. The composition and mechanism of GA-HA-CNC hydrogels were confirmed by FTIR. The morphology and pore size were obtained by SEM. We accessed the physical property from rheological results and swelling ratio. NIH-3T3 cells were inoculated into the hydrogels and cultured for different days, then we analyzed the cytotoxicity of the prepared hydrogels by CCK-8 methods and live/dead pictorial diagram using staining kits. FTIR revealed the combination between GA, HA and CNC was attributed to the amide bond and hydrogen bonding. SEM results showed that the drying GA-HA-CNC hydrogels were spongy, with the pore diameter about 80-120 µm. CNC significantly enhanced the property of the hydrogels and play a vital role according to the rheology and swelling results. The cells culture results showed that NIH-3T3 cells can attached to, grow, and proliferate well on the GA-HA-CNC hydrogels. In conclusion, the natural GA-HA-CNC hydrogel has great potential for the skin wound repair.

Thermoplastic Processing of PLA/Cellulose Nanomaterials Composites

Over the past decades, research has escalated on the use of polylactic acid (PLA) as a replacement for petroleum-based polymers. This is due to its valuable properties, such as renewability, biodegradability, biocompatibility and good thermomechanical properties. Despite possessing good mechanical properties comparable to conventional petroleum-based polymers, PLA suffers from some shortcomings such as low thermal resistance, heat distortion temperature and rate of crystallization, thus different fillers have been used to overcome these limitations. In the framework of environmentally friendly processes and products, there has been growing interest on the use of cellulose nanomaterials viz. cellulose nanocrystals (CNC) and nanofibers (CNF) as natural fillers for PLA towards advanced applications other than short-term packaging and biomedical. Cellulosic nanomaterials are renewable in nature, biodegradable, eco-friendly and they possess high strength and stiffness. In the case of eco-friendly processes, various conventional processing techniques, such as melt extrusion, melt-spinning, and compression molding, have been used to produce PLA composites. This review addresses the critical factors in the manufacturing of PLA-cellulosic nanomaterials by using conventional techniques and recent advances needed to promote and improve the dispersion of the cellulosic nanomaterials. Different aspects, including morphology, mechanical behavior and thermal properties, as well as comparisons of CNC- and CNF-reinforced PLA, are also discussed.

Star-like Supramolecular Complexes of Reducing-End-Functionalized Cellulose Nanocrystals

In this work, we take advantage of the parallel organization of cellulose chains in cellulose I yielding an inherent chemical asymmetry of cellulose nanocrystals, i.e., reducing vs nonreducing end, to selectively modify only one end of these rigid rodlike crystals to be used as a linking point for the formation of supramolecular structures. We have prepared biotin-functionalized tunicate cellulose nanocrystals at the reducing end capable of forming new complex supramolecular hierarchies by the addition of the protein streptavidin. Biotin-streptavidin coupling was chosen because streptavidin has a multivalency of four and the biotin-streptavidin bond is known to be highly selective and stable. Hence, streptavidin molecules would link up to four cellulose nanocrystals through their biotin-modified reducing end. Two biotin derivatives were studied, consisting of an anchoring group, i.e., amine or hydrazine; the biotin moiety; and the linker between them. Results show that the length of the linker significantly affects the bond between the biotinylated cellulose nanocrystals and streptavidin, and a certain chain length is necessary for the supramolecular assembly of several cellulose nanocrystals by streptavidin.

Facile Tuning of the Surface Energy of Cellulose Nanofibers for Nanocomposite Reinforcement

The isolation of nanocellulose from lignocellulosic biomass, with desirable surface chemistry and morphology, has gained extensive scientific attention for various applications including polymer nanocomposite reinforcement. Additionally, environmental and economic concerns have driven researchers to explore viable alternatives to current isolation approaches, employing chemicals with reduced environmental impact. To address these issues, in this study, we have tuned the amphiphilic behavior of cellulose nanofibers (CNFs) by employing controlled alkali treatment, instead of in combination with expensive, environmentally unsustainable conventional approaches. Microscopic and spectroscopic analysis demonstrated that this approach is capable of tuning composition and interfacial tension of CNFs through a careful control of the quantity of residual lignin and hemicellulose. To elucidate the performance of CNF as an efficient reinforcing nanofiller in hydrophobic polymer matrices, prevulcanized natural rubber (NR) latex was employed as a suitable host polymer. CNF/NR nanocomposites with different CNF loading levels (0.1-1 wt % CNF) were prepared by a casting method. It was found that the incorporation of 0.1 wt % CNF treated with a 0.5 w/v % sodium hydroxide solution led to the highest latex reinforcement efficiency, with an enhancement in tensile stress and toughness of 16% to 42 MPa and 9% to 197 MJ m^-3, respectively. This property profile offers a potential application for the high-performance medical devices such as condoms and gloves.

TEMPO-oxidised cellulose nanofibrils; probing the mechanisms of gelation via small angle X-ray scattering

The structure of dispersions of TEMPO-oxidised cellulose nanofibrils (OCNF), at various concentrations, in water and in NaCl aqueous solutions, was probed using small angle X-ray scattering (SAXS). OCNF are modelled as rod-like particles with an elliptical cross-section of 10 nm and a length greater than 100 nm. As OCNF concentration increases above 1.5 wt%, repulsive interactions between fibrils are evidenced, modelled by the interaction parameter νRPA > 0. This corresponds to gel-like behaviour, where G' > G'' and the storage modulus, G', shows weak frequency dependence. Hydrogels can also be formed at OCNF concentration of 1 wt% in 0.1 M NaCl(aq). SAXS patterns shows an increase of the intensity at low angle that is modelled by attractive interactions (νRPA < 0) between OCNF, arising from the screening of the surface charge of the fibrils. Results are supported by ζ potential and cryo-TEM measurements.