Nano zinc oxide-sodium alginate antibacterial cellulose fibres

Therapeutic strategies for drug-resistant Pseudomonas aeruginosa: Metal and metal oxide nanoparticles

Pseudomonas aeruginosa (PA) is a widely prevalent opportunistic pathogen. Multiple resistant strains of PA have emerged from excessive or inappropriate use of antibiotics, making their eradication increasingly difficult. Therefore, the search for highly efficient and secure novel antimicrobial agents is crucial. According to reports, there is an increasing exploration of nanometals for antibacterial purposes. The antibacterial mechanisms involving the nanomaterials themselves, the release of ions, and the induced oxidative stress causing leakage and damage to biomolecules are widely accepted. Additionally, the study of the cytotoxicity of metal nanoparticles is crucial for their antibacterial applications. This article summarizes the types of metal nanomaterials and metal oxide nanomaterials that can be used against PA, their respective unique antibacterial mechanisms, cytotoxicity, and efforts made to improve antibacterial performance and reduce toxicity, including combination therapy with other materials and antibiotics, as well as green synthesis approaches.

Exploring the Feasibility of Polysaccharide-Based Mulch Films with Controlled Ammonium and Phosphate Ions Release for Sustainable Agriculture

Bio-based polymers are a promising material with which to tackle the use of disposable and non-degradable plastics in agriculture, such as mulching films. However, their poor mechanical properties and the high cost of biomaterials have hindered their widespread application. Hence, in this study, we improved polysaccharide-based films and enriched them with plant nutrients to make them suitable for mulching and fertilizing. Films were produced combining sodium carboxymethyl cellulose (CMC), chitosan (CS), and sodium alginate (SA) at different weight ratios with glycerol and CaCl2 as a plasticizer and crosslinker, respectively, and enriched with ammonium phosphate monobasic (NH4H2PO4). A polysaccharide weight ratio of 1:1 generated a film with a more crosslinked structure and a lower expanded network than that featuring the 17:3 ratio, whereas CaCl2 increased the films' water resistance, thermal stability, and strength characteristics, slowing the release rates of NH4+ and PO43-. Thus, composition and crosslinking proved crucial to obtaining promising films for soil mulching.

High Tensile, Antibacterial, and Conductive Hydrogel Sensor with Multiple Cross-Linked Networks Based on PVA/Sodium Alginate/Zinc Oxide

Hydrogel sensors have attracted a lot of attention due to their great significance for biosensors and human detection, especially their antibacterial properties when in direct contact with the human body. However, it is challenging to improve mechanical and antibacterial performance simultaneously. In this study, by using ultrasonic dispersion technology to attach zinc oxide to cellulose and adding sodium alginate, a multiple cross-linking network is generated, which effectively solves this problem. The proposed poly(vinyl alcohol)/sodium alginate/zinc oxide/hydrogel sensor exhibits not only excellent biocompatibility but also high tensile properties (strain above 2000%). Besides, the sensor also has an antibacterial function (against Escherichia coli and Staphylococcus aureus). The hydrogel acts as a strain sensor and biosensor; it can also be used as a human health detection sensor; its high tensile properties can detect large tensile deformation and small changes in force, such as finger bending, knee bending, and other joint movements, and can also be used as a sound detection sensor to detect speech and breathing. This study provides a simple method to prepare hydrogel sensors that can be useful for human health detection and biosensor development.

Characterization of Acellular Cartilage Matrix-Sodium Alginate Scaffolds in Various Proportions

The development of three-dimensional (3D) bioprinting technology has provided a new solution to address the shortage of donors, multiple surgeries, and aesthetic concerns in microtia reconstruction surgery. The production of bioinks is the most critical aspect of 3D bioprinting. Acellular cartilage matrix (ACM) and sodium alginate (SA) are commonly used 3D bioprinting materials, and there have been reports of their combined use. However, there is a lack of comprehensive evaluations on ACM-SA scaffolds with different proportions. In this study, bioinks were prepared by mixing different proportions of decellularized rabbit ear cartilage powder and SA and then printed using 3D bioprinting technology and crosslinked with calcium ions to fabricate scaffolds. The physical properties, biocompatibility, and toxicity of ACM-SA scaffolds with different proportions were compared. The adhesion and proliferation of rabbit adipose-derived stem cells on ACM-SA scaffolds of different proportions, as well as the secretion of Collagen Type II, were evaluated under an adipose-derived stem cell chondrogenic induction medium. The following conclusions were drawn: when the proportion of SA in the ACM-SA scaffolds was <30%, the printed structure failed to form. The ACM-SA scaffolds in proportions from 1:9 to 6:4 showed no significant cytotoxicity, among which the 5:5 proportion of ACM-SA scaffold was superior in terms of adhesiveness and promoting cell proliferation and differentiation. Although a higher proportion of SA can provide greater mechanical strength, it also significantly increases the swelling ratio and reduces cell proliferation capabilities. Overall, the 5:5 proportion of ACM-SA scaffold demonstrated a more desirable biological and physical performance.

Multifunctional modification polyester with Au@Cu2O-ZnO ternary heterojunction fabricated by in situ polymerization

In situ polymerization has been proven to be an effective method to introduce functional materials into polymers. In this work, a nano-heterojunction material was prepared successfully and evenly dispersed in PET by in situ polymerization methods to yield multifunctionally modified PET. The modified PET fibers showed excellent antibacterial activity and strong moisture absorption and perspiration, which could efficiently expel moisture from humans. Significantly, these prepared PET textiles demonstrate a strong safety without any cytotoxicity. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed the uniform dispersion of heterojunctions and well-defined truncated octahedra including nano-gold rods. A series of characterizations including FTIR, XPS, XRD and DSC showed that the nano-heterojunction participates in the reaction during polymerization. It is interesting that the SEM images of the modified PET fiber presented an intriguing organ fold structure, which makes a significant contribution to moisture absorption and perspiration. The formation mechanism is discussed preliminarily.

Enzyme-triggered approach to reduce water bodies' contamination using peroxidase-immobilized ZnO/SnO2/alginate nanocomposite

Enzyme immobilization on solid support offers advantages over free enzymes by overcoming characteristic limitations. To synthesize new stable and hyperactive nano-biocatalysts (co-precipitation method), ginger peroxidase (GP) was surface immobilized (adsorption) on ZnO/SnO2 and ZnO/SnO2/SA nanocomposite with immobilization efficacy of 94 % and 99 %, respectively. Thereafter, catalytic and biochemical characteristics of free and immobilized GP were investigated by deploying various techniques, i.e., FTIR, PXRD, SEM, and PL. Diffraction peaks emerged at 2θ values of 26°, 33°, 37°, 51°, 31°, 34°, 36°, 56°, indicating the formation of SnO2 and ZnO. The OH stretching of the H2O molecules was attributed to broad peaks between 3200 and 3500 cm-1, whereas ZnO/SnO2 spikes occurred in the 1626-1637 cm-1 range. SnO stretching mode and ZnO terminal vibrational patterns have been verified at corresponding wavelengths of 625 cm-1 and 560 cm-1. Enzyme entrapment onto substrate was verified via interactions between GP and ZnO/SnO2/SA as corroborated by signals beneath 1100 cm-1. GP-immobilized fractions were optimally active at pH 5, 50 °C, and retained maximum activity after storage of 4 weeks at -4 °C. Kinetic parameters were determined by using a Lineweaver-Burk plot and Vmax for free GP, ZnO/SnO2/GP and ZnO/SnO2/SA/GP with guaiacol as a substrate, were found to be 322.58, 49.01 and 11.45 (μM/min) respectively. A decrease in values of Vmax and KM indicates strong adsorption of peroxidase on support and maximum affinity between nano support and enzyme, respectively. For environmental remediation, free ginger peroxidase (GP), ZnO/SnO2/GP and ZnO/SnO2/SA/GP fractions effectively eradicated highly intricate dye. Multiple scavengers had a significant impact on the depletion of the dye. In conclusion, ZnO/SnO2 and ZnO/SnO2/SA nanostructures comprise an ecologically acceptable and intriguing carrier for enzyme immobilization.

Improved cotton fabrics properties using zinc oxide-based nanomaterials: A review

Zinc oxide nanoparticles (ZnO NPs) have gained significant attention in the textile industry for their ability to enhance the physicochemical properties of fabrics. In recent years, there has been a growing focus on the development of ZnO-based nanomaterials and their applications for cotton and other fabrics. This review paper provides an overview of the synthesis and diverse applications of ZnO-based nanomaterials for textile fabrics, including protection against UV irradiation, bacteria, fungi, microwave, electromagnetic radiation, water, and fire. Furthermore, the study offers the potential of these materials in energy harvesting applications, such as wearable pressure sensors, piezoelectric nanogenerators, supercapacitors, and human energy harvesting. Additionally, we discuss the potential of ZnO-based nanomaterials for environmental cleaning, including water, oil, and solid cleaning. The current research in this area has focused on various materials used to prepare ZnO-based nanocomposites, such as metals/nonmetals, semiconductors, metal oxides, carbon materials, polymers, MXene, metal-organic frameworks, and layered double hydroxides. The findings of this review highlight the potential of ZnO-based nanomaterials to improve the performance of textile fabrics in a range of applications, and the importance of continued research in this field to further advance the development and use of ZnO-based nanomaterials in the textile industry.

Nano-copper ions assembled cellulose-based composite with antibacterial activity for biodegradable personal protective mask

The current SARS-CoV-2 pandemic has resulted in the widespread use of personal protective equipment, particularly face masks. However, the use of commercial disposable face masks puts great pressure on the environment. In this study, nano-copper ions assembled cotton fabric used in face masks to impart antibacterial activity has been discussed. To produce the nanocomposite, the cotton fabric was modified by sodium chloroacetate after its mercerization, and assembled with bactericidal nano-copper ions (about 10.61 mg·g-1) through electrostatic adsorption. It demonstrated excellent antibacterial activity against Staphylococcus aureus and Escherichia coli because the gaps between fibers in the cotton fabric allow the nano-copper ions to be fully released. Moreover, the antibacterial efficiency was maintained even after 50 washing cycles. Furthermore, the face mask constructed with this novel nanocomposite upper layer exhibited a high particle filtration efficiency (96.08% ± 0.91%) without compromising the air permeability (28.9 min·L-1). This green, economical, facile, and scalable process of depositing nano-copper ions onto modified cotton fibric has great potential to reduce disease transmission, resource consumption, and environmental impact of waste, while also expanding the range of protective fabrics.

The Antibacterial Activities and Characterizations of Biosynthesized Zinc Oxide Nanoparticles, and Their Coated with Alginate Derived from Fucus vesiculosus

Zinc oxide nanoparticles have many advantages for nano-biotechnologists due to their intense biomedical applications. ZnO-NPs are used as antibacterial agents, which influence bacterial cells through the rupture of the cell membrane and the generation of reactive free radicals. Alginate is a polysaccharide of natural origin due to its excellent properties that are used in various biomedical applications. Brown algae are good sources of alginate and are used as a reducing agent in the synthesis of nanoparticles. This study aims to synthesize ZnO-NPs by using brown alga Fucus vesiculosus (Fu/ZnO-NPs) and also to extract alginate from the same alga, which is used in coating the ZnO-NPs (Fu/ZnO-Alg-NCMs). The characterizations of Fu/ZnO-NPs and Fu/ZnO-Alg-NCMs were determined by FTIR, TEM, XRD, and zeta potential. The antibacterial activities were applied against multidrug resistance bacteria of both gram-positive and negative. The results obtained in FT-TR showed there are some shifts in the peak positions of Fu/ZnO-NPs and Fu/ZnO-Alg-NCMs. The peak at 1655 cm^-1, which assigned amide I-III, is present in both Fu/ZnO-NPs and Fu-Alg-ZnO-NCMs; this band is responsible for bio-reductions and stabilization of both nanoparticles. The TEM images proved the Fu/ZnO-NPs have rod shapes with sizes ranging from 12.68 to 17.66 and are aggregated, but Fu/ZnO/Alg-NCMs are spherical in shape with sizes ranging from 12.13 to 19.77. XRD-cleared Fu/ZnO-NPs have nine sharp peaks that are considered good crystalline, but Fu/ZnO-Alg-NCMs have four broad and sharp peaks that are considered semi-crystalline. Both Fu/ZnO-NPs and Fu/ZnO-Alg-NCMs have negative charges (-1.74 and -3.56, respectively). Fu/ZnO-NPs have more antibacterial activities than Fu/ZnO/Alg-NCMs in all tested multidrug-resistant bacterial strains. Fu/ZnO/Alg-NCMs had no effect on Acinetobacter KY856930, Staphylococcus epidermidis, and Enterobacter aerogenes, whereas there was an apparent effect of ZnO-NPs against the same strains.

Hybrid nanomaterial composed of chitosan, curcumin, ZnO and TiO2 for antibacterial therapies

Metal nanoparticles have been tremendously utilised, such as; antibacterial and anticancer agents. Although metal nanoparticles exhibits antibacterial and anticancer activity, but the drawback of toxicity on normal cells limits their clinical applications. Therefore, improving the bioactivity of hybrid nanomaterials (HNMs) and minimizing toxicity is of paramount importance for biomedical applications. Herein, a facile and simple double precipitation method was used to develop biocompatible and multifunctional HNM from antimicrobial chitosan, curcumin, ZnO and TiO₂. In HNM, biomolecules chitosan and curcumin were used to control the toxicity of ZnO and TiO₂ and improve their biocidal properties. The cytotxicological properties of the HNM was studied against human breast cancer (MDA-MB-231) and fibroblast (L929) cell lines. The antimicrobial activity of the HNM was examined against Escherichia coli and Staphylococcus aureus bacteria, via the well-diffusion method. In addition, the antioxidant property was evaluated by the radical scavenging method. These findings actively, support the ZTCC HNMs potential, as an innovative biocidal agent for applications in the clinical and healthcare sectors.

Compressible polyaniline-coated sodium alginate-cattail fiber foam for efficient and salt-resistant solar steam generation

Solar steam generation has attracted widespread attention because of its ability to produce clean water through desalination and wastewater treatment without conventional energy consumption. In this work, a polyaniline (PANI)-coated sodium alginate (SA)/cattail fiber (CF) foam for photothermal evaporator is prepared via directional freezing and oxidative polymerization. The SA/CF foam displays desirable water pumping capability because of the lamellar sandwich structure interconnected by porous networks. More importantly, the directional porous network architecture ameliorates the mechanical and salt-resistant performances of the SA/CF foam. The as-prepared PANI@SA/CF foam shows inferior heat conductivity of 0.047 W m^-1 K^-1 and outstanding light absorption over 96% in solar window. A vapor evaporation rate of 2.04 kg m^-2 h^-1 under 1 sun illumination is achieved for the PANI@SA/CF evaporator. Furthermore, the PANI@SA/CF foam could be employed in solar-driven freshwater generation from seawater and wastewater with high ion and dye removal rates. The combination of water evaporation and cleaning capabilities of the PANI@SA/CF foam as photothermal materials provide a framework for the exploration of next-generation evaporators in seawater desalination and wastewater treatment applications.

Composite films based on carboxy methyl cellulose and sodium alginate incorporated Thymus vulgaris purified leaves extract for food application: Assessment, antimicrobial and antioxidant properties

The current study was conducted to develop biodegradable films with matrix composed from carboxymethyl cellulose (CMC), sodium alginate (SA) and different concentrations from Thymus vulgaris purified leaves extract (TVE). The color properties, physical properties, shape of surface, manners of crystallinity, mechanical properties and thermal properties of produced films were investigated. The continuous addition of TVE up to 1.6 % inside films matrix imparted the yellow color of extract that increased opacity to 2.98 and reduced moisture, swelling, solubility and water vapor permeability (WVP) of films up to 10.31 %, 30.17 %, 20.18 % and (1.12× 10^-10 g.m^-1 s^-1 pa^-1), respectively. Furthermore, the surface micrographs showed smoother surface after using small concentrations of TVE and turned to irregular with rough surface at higher concentrations. The FT-IR analysis indicated typically bands that demonstrated physical interaction between TVE extract and CMC/SA matrix. The fabricated films showed suitable thermal stability with decreasing trend by incorporation of TVE inside CMC/SA films. Furthermore, the developed CMC/SA/TVE2 showed significant effects on preserving the levels of moisture content, titrable acidity, force to puncture and sensory properties of cheddar cheese during cold storage days compared with commercial packaging materials.

Cellulosic fiber nanocomposite application review with zinc oxide antimicrobial agent nanoparticle: an opt for COVID-19 purpose

Cellulosic fiber (CF) in nanoform is emergingly finding its way for COVID-19 solution for instance via nanocomposite/nanoparticle from various abundant biopolymeric waste materials, which may not be widely commercialized when the pandemic strikes recently. The possibility is wide open but needs proper collection of knowledge and research data. Thus, this article firstly reviews CF produced from various lignocellulosic or biomass feedstocks' pretreatment methods in various nanoforms or nanocomposites, also serving together with metal oxide (MeO) antimicrobial agents having certain analytical reporting. CF-MeO hybrid product can be a great option for COVID-19 antimicrobial resistant environment to be proposed considering the long-established CF and MeO laboratory investigations. Secondly, a preliminary pH investigation of 7 to 12 on zinc oxide synthesis discussing on Fouriertransform infrared spectroscopy (FTIR) functional groups and scanning electron microscope (SEM) images are also presented, justifying the knowledge requirement for future stable nanocomposite formulation. In addition to that, recent precursors suitable for zinc oxide nanoparticle synthesis with emergingly prediction to serve as COVID-19 purposes via different products, aligning with CFs or nanocellulose for industrial applications are also reviewed.

Solution blowing spinning of polylactate/polyvinyl alcohol/ZnO nanocomposite toward green and sustainable preparation of wound dressing nanofibrous films

The outstanding biodegradability, biocompatibility, affordability, and renewability of polylactic acid have made it a prominent biomaterial. Herein, an innovative, easy, and eco-friendly technique is used to prepare sodium polylactate (SP)-based nanofibers. Solution blowing spinning (SBS) was used to create fibrous mats of SP and polyvinyl alcohol (PVA). SBS's SP nanfibers were crosslinked using an aqueous solution of calcium chloride to produce moisture-resistant calcium polylactate nanofibrous spun mats. Both of UV-visible absorption spectra and transmission electron microscopy were utilized to study the produced zinc oxide (ZnO) nanoparticles (NPs) to indicate a diameter of around 15-23 nm with a high intensity absorption intensity at 370 nm. New polylactate copolymer was synthesized and characterized by infrared and NMR spectroscopic techniques. In order to prepare SP/PVA/ZnO nanocomposite nanofibers, various ZnO ratios were used. The morphologies of the composite nanofibers were investigated by infrared spectroscopy (FTIR), energy-dispersive X-ray analyzer, and scanning electron microscopy. The cytotoxicity tests of the prepared mat were studied by conducting experiments with L-929 cells at various time intervals. The prepared composite SP/PVA/ZnO nanofibers were subjected to cytotoxicity tests to determine their cytocompatibility. Results showed that those with ZnO concentrations between 0.5% and 2% were found to be less harmful than those with higher concentrations. A variety of bacterial species, including Bacillus pumilus and Staphylococcus aureus, as well as Klebseilla pneumoniae and Escherichia coli, were used to test the antibacterial properties of SP/PVA/ZnO spun mats. The ZnO NPs integrated in the SP/PVA fibrous mats were responsible for their antibacterial properties. After finding the appropriate concentration of ZnO that is least harmful while yet giving a satisfactory antibacterial activity, this biomaterial might be perfect for wound dressing applications. HIGHLIGHTS: New eco-friendly biodegradable sodium polylactate (SP) copolymer was synthesized. Zinc oxide nanoparticles (ZnO NPs) with a diameter of 15-23 nm were prepared. High antibacterial SP/PVA/ZnO fibers were prepared by solution blowing spinning. SP/PVA/ZnO nanofibers (180-220 nm) with various ratios of ZnO were presented. Cytotoxicity results showed that the cell viability decreases with increasing ZnO.

The Fabrication of Alginate–Carboxymethyl Cellulose-Based Composites and Drug Release Profiles

Recently, hydrogels based on natural water-soluble polysaccharides have attracted more and more attention due to their favorable characteristics. The high water-holding capacity, lack of toxicity, and biodegradability of such hydrogels make it possible to develop new materials on their basis for biotechnological, biomedical, pharmacological, and medical purposes. Sodium alginate is a non-toxic natural polysaccharide found in marine algae. It is capable of forming solid gels under the action of polyvalent cations that cross-link polysaccharide chains. Alginate-based products are popular in many industries, including food processing, pharmaceutical, and biomedical applications. Cellulose is the most abundant, renewable, and natural polymer on Earth, and it is used for various industrial and biomedical applications. Carboxymethyl cellulose (CMC) is useful in pharmaceutical, food, and non-food industries such as tablets, ice cream, drinks, toothpaste, and detergents. In this review, various methods for the preparation of the compositions based on sodium alginate and CMC using different crosslinking agents have been collected for the first time. Additionally, the drug release profile from such polymer matrixes was analyzed.

Nanomaterials-Based Combinatorial Therapy as a Strategy to Combat Antibiotic Resistance

Since the discovery of antibiotics, humanity has been able to cope with the battle against bacterial infections. However, the inappropriate use of antibiotics, the lack of innovation in therapeutic agents, and other factors have allowed the emergence of new bacterial strains resistant to multiple antibiotic treatments, causing a crisis in the health sector. Furthermore, the World Health Organization has listed a series of pathogens (ESKAPE group) that have acquired new and varied resistance to different antibiotics families. Therefore, the scientific community has prioritized designing and developing novel treatments to combat these ESKAPE pathogens and other emergent multidrug-resistant bacteria. One of the solutions is the use of combinatorial therapies. Combinatorial therapies seek to enhance the effects of individual treatments at lower doses, bringing the advantage of being, in most cases, much less harmful to patients. Among the new developments in combinatorial therapies, nanomaterials have gained significant interest. Some of the most promising nanotherapeutics include polymers, inorganic nanoparticles, and antimicrobial peptides due to their bactericidal and nanocarrier properties. Therefore, this review focuses on discussing the state-of-the-art of the most significant advances and concludes with a perspective on the future developments of nanotherapeutic combinatorial treatments that target bacterial infections.

A Review on Antibacterial Biomaterials in Biomedical Applications: From Materials Perspective to Bioinks Design

In tissue engineering, three-dimensional (3D) printing is an emerging approach to producing functioning tissue constructs to repair wounds and repair or replace sick tissue/organs. It allows for precise control of materials and other components in the tissue constructs in an automated way, potentially permitting great throughput production. An ink made using one or multiple biomaterials can be 3D printed into tissue constructs by the printing process; though promising in tissue engineering, the printed constructs have also been reported to have the ability to lead to the emergence of unforeseen illnesses and failure due to biomaterial-related infections. Numerous approaches and/or strategies have been developed to combat biomaterial-related infections, and among them, natural biomaterials, surface treatment of biomaterials, and incorporating inorganic agents have been widely employed for the construct fabrication by 3D printing. Despite various attempts to synthesize and/or optimize the inks for 3D printing, the incidence of infection in the implanted tissue constructs remains one of the most significant issues. For the first time, here we present an overview of inks with antibacterial properties for 3D printing, focusing on the principles and strategies to accomplish biomaterials with anti-infective properties, and the synthesis of metallic ion-containing ink, chitosan-containing inks, and other antibacterial inks. Related discussions regarding the mechanics of biofilm formation and antibacterial performance are also presented, along with future perspectives of the importance of developing printable inks.

Potential risks and approaches to reduce the toxicity of disinfection by-product - A review

Water contamination through anthropogenic and industrial activities has led to the emergence and necessity of disinfection methods. Chlorine and bromine gases, often used to disinfect water, resulted in the by-product formation by reacting with organic matter. The Disinfectant by-products (DBP) led to the formation of Trihaloaceticacid (TAA), Trihalomethane (THM), and other minor components. The release of chemicals has also led to the outbreak of diseases like infertility, asthma, stillbirth, and types of cancer. There are new approaches that are found to be useful to compensate for the generation of toxic by-products and involve membrane technologies, namely reverse osmosis, ultrafiltration, and nanofiltration. This review mainly focuses on the toxicology effects of DBPs and various approaches to mitigate the same. The health hazards caused by different DBPs and the various treatment techniques available for the removal are discussed. In addition, a critical comparison of the different removal techniques was discussed.

Development of green and sustainable smart biochromic and therapeutic bandage using red cabbage (Brassica oleracea L. Var. capitata) extract encapsulated into alginate nanoparticles

Novel multifunctional wound dressing with the ability to protect, cure and sense the healing process, was developed. Red-cabbage extract has been reported to exhibit bioactive compounds with the ability to function as antioxidant, antiinflammatory, anticancer, antibacterial, antifungal, and antiviral agent, as well as a natural pH-sensory chromophoric material. An anthocyanin extract was prepared from Red-cabbage (Brassica oleracea L. Var. capitata). The anthocyanins extract was encapsulated into calcium alginate in the presence of potash alum mordant, which was then applied to the surface of the cotton gauze. Red-cabbage based anthocyanin chromophoric extract was encapsulated at different concentrations into alginate-based hydrogel and immobilized into cotton gauze to provide a smart therapeutic pH-responsive wound dress to function as an antimicrobial and biochromic matrix providing a comfortable dress sensor to monitor the wound status. Decreasing the pH of a wound mimic solution caused a blue shift from 579 to 437 nm. The anthocyanin spectroscopic probe's halochromic activity demonstrated a colorimetric change from purple to pink, which was critical to the dyed cotton diagnostic assay's biochromic performance. The colorimetric parameters of the prepared dressing sensor were proved by UV-Vis absorbance and CIE Lab coordinates. Both mechanical and morphological properties of the prepared dressing were studied using different analytical methods. The effect of anthocyanin concentration on the mechanical, water vapor permeability, water absorption and morphological properties of the wound dressing were investigated. No substantial flaws in air-permeability or bend length were detected after dyeing. The colored cotton gauze samples were tested for their high colorfastness. The cytotoxicity and antimicrobial activity of the prepared biochromic cotton gauze were explored. The dyed cotton samples exhibited no cytotoxicity and improved antimicrobial activity with increasing the anthocyanin ratio on cotton surface.

Development of a Microenvironment-Responsive Hydrogel Promoting Chronically Infected Diabetic Wound Healing through Sequential Hemostatic, Antibacterial, and Angiogenic Activities

Microenvironment-responsive hydrogels present high potential in treating refractory wounds due to their capability of on-demand drug release. In this study, a specially designed hydrogel with smart targeting of refractory wound characteristics was designed to treat chronically infected diabetic wounds. Aminated gelatin reacted with oxidized dextran, forming a hydrogel cross-linked with a dynamic Schiff base, which is sensitive to the low-pH environment in refractory wounds. Nano-ZnO was loaded into the hydrogel for killing microbes. A Paeoniflorin-encapsulated micelle with a ROS-responsive property was fixed to the skeleton of the hydrogel via a Schiff base bond for low-pH- and ROS-stimulated angiogenic activity. The sequential responsiveness of the novel hydrogel enabled smart rescue of the deleterious microenvironment in refractory wounds. This highly biocompatible hydrogel demonstrated antibacterial and angiogenic abilities in vitro and significantly promoted healing of chronically infected diabetic wounds via sequential hemostatic, microbe killing, and angiogenic activities. This microenvironment-responsive hydrogel loaded with nZnO and Pf-encapsulated micelles holds great potential as a location-specific dual-response delivery platform for curing refractory, chronically infected diabetic wounds.

Alginate: Enhancement Strategies for Advanced Applications

Alginate is an excellent biodegradable and renewable material that is already used for a broad range of industrial applications, including advanced fields, such as biomedicine and bioengineering, due to its excellent biodegradable and biocompatible properties. This biopolymer can be produced from brown algae or a microorganism culture. This review presents the principles, chemical structures, gelation properties, chemical interactions, production, sterilization, purification, types, and alginate-based hydrogels developed so far. We present all of the advanced strategies used to remarkably enhance this biopolymer's physicochemical and biological characteristics in various forms, such as injectable gels, fibers, films, hydrogels, and scaffolds. Thus, we present here all of the material engineering enhancement approaches achieved so far in this biopolymer in terms of mechanical reinforcement, thermal and electrical performance, wettability, water sorption and diffusion, antimicrobial activity, in vivo and in vitro biological behavior, including toxicity, cell adhesion, proliferation, and differentiation, immunological response, biodegradation, porosity, and its use as scaffolds for tissue engineering applications. These improvements to overcome the drawbacks of the alginate biopolymer could exponentially increase the significant number of alginate applications that go from the paper industry to the bioprinting of organs.

Nanomaterials for application in wound Healing: current state-of-the-art and future perspectives

Nanoparticles are the gateway to the new era in drug delivery of biocompatible agents. Several products have emerged from nanomaterials in quest of developing practical wound healing dressings that are nonantigenic, antishear stress, and gas-exchange permeable. Numerous studies have isolated and characterised various wound healing nanomaterials and nanoproducts. The electrospinning of natural and synthetic materials produces fine products that can be mixed with other wound healing medications and herbs. Various produced nanomaterials are highly influential in wound healing experimental models and can be used commercially as well. This article reviewed the current state-of-the-art and briefly specified the future concerns regarding the different systems of nanomaterials in wound healing (i.e., inorganic nanomaterials, organic and hybrid nanomaterials, and nanofibers). This review may be a comprehensive guidance to help health care professionals identify the proper wound healing materials to avoid the usual wound complications.

Application of Alginate-Based Hydrogels in Hemostasis

Hemorrhage, as a common trauma injury and clinical postoperative complication, may cause serious damage to the body, especially for patients with huge blood loss and coagulation dysfunction. Timely and effective hemostasis and avoidance of bleeding are of great significance for reducing body damage and improving the survival rate and quality of life of patients. Alginate is considered to be an excellent hemostatic polymer-based biomaterial due to its excellent biocompatibility, biodegradability, non-toxicity, non-immunogenicity, easy gelation and easy availability. In recent years, alginate hydrogels have been more and more widely used in the medical field, and a series of hemostatic related products have been developed such as medical dressings, hemostatic needles, transcatheter interventional embolization preparations, microneedles, injectable hydrogels, and hemostatic powders. The development and application prospects are extremely broad. This manuscript reviews the structure, properties and history of alginate, as well as the research progress of alginate hydrogels in clinical applications related to hemostasis. This review also discusses the current limitations and possible future development prospects of alginate hydrogels in hemostatic applications.

Silver Nanoparticle-Decorated Personal Protective Equipment for Inhibiting Human Coronavirus Infectivity

The Coronavirus disease 2019 (COVID-19) global outbreak and its continued growth and mutation into various forms emphasize the need for effective disinfectants to assist in the reduction of the virus's spread from individual to individuals and community to communities through various modes, including coughing, sneezing, touching of contaminated surfaces, and being in proximity of an unprotected infected person, to mention a few. The rapid development of reliable disinfecting materials or solutions and their incorporation in personal protective equipment is a critical need at the moment that will assist significantly in curbing the spread of the virus SARS-CoV-2, the cause of COVID-19 illness. Here, we present an in situ assembly of antiviral metal nanoparticles on a rigid surface and on commercial face masks made up of nonwoven and woven textiles. The results indicate a very high efficacy of 99.99% against a surrogate virus to SARS-CoV-2. Such a versatile and cost-effective approach using the blade-coating technique can be easily extended to the roll-to-roll manufacturing setting to expedite the efforts and mitigate the rapid spread of the virus.

Biocidal and biocompatible hybrid nanomaterials from biomolecule chitosan, alginate and ZnO

Biocidal activity and biocompatibility of nanomaterials (NMs) are crucial for healthcare applications. This study aims to develop biocidal hybrid NMs with high inhibition rates to control multidrug-resistant bacterial infection compared to conventional antibiotics. Herein, ZnO, chitosan-ZnO (CZnO) and alginate-ZnO (AZnO) NMs were synthesized via a simple one-pot technique. The one-pot process facilitates the efficiency of a chemical reaction whereby a reactant is subjected to successive chemical reactions in just one step. The resulted NMs bio-physicochemical features were analyzed using various analytical methods. The bactericidal and bacteriostatic mechanism of NMs strongly depends on the production of reactive oxygen species in NMs, due to their size, large surface areas, oxygen vacancies, ion release, and diffusion ability. The antibacterial potential of the NMs was tested against methicillin-resistant Staphylococcus aureus. The inhibition zone disclosed that the AZnO possessed an excellent antibacterial activity compared to ZnO and CZnO. Furthermore, toxicity studies revealed that the AZnO demonstrated low toxicity to the HepG2 cell lines. These results confirmed that the AZnO hybrid nanomaterials are promising futuristic biocidal agents suitable for the clinical and healthcare industries.

The Usages and Potential Uses of Alginate for Healthcare Applications

Due to their unique properties, alginate-based biomaterials have been extensively used to treat different diseases, and in the regeneration of diverse organs. A lot of research has been done by the different scientific community to develop biofilms for fulfilling the need for sustainable human health. The aim of this review is to hit upon a hydrogel enhancing the scope of utilization in biomedical applications. The presence of active sites in alginate hydrogels can be manipulated for managing various non-communicable diseases by encapsulating, with the bioactive component as a potential site for chemicals in developing drugs, or for delivering macromolecule nutrients. Gels are accepted for cell implantation in tissue regeneration, as they can transfer cells to the intended site. Thus, this review will accelerate advanced research avenues in tissue engineering and the potential of alginate biofilms in the healthcare sector.

Functionalizing Ti3C2Tx for enhancing fire resistance and reducing toxic gases of flexible polyurethane foam composites with reinforced mechanical properties

Flexible polyurethane foam (FPUF) is the most used polyurethane, but the highly flammable characteristic limits its widespread usage. In this work, ZIF-8@Ti₃C₂T_xwas synthesized to reduce the heat and toxic gases of FPUF. Flame-retardant FPUF was characterized by cone calorimeter (Cone), thermogravimetric analysis/fourier-transform infrared spectroscopy (TG-FTIR), tensileand compression tests. Compared with pure FPUF, these results showed that the peak of heat release rate (PHRR), total heat release (THR), CO and HCN of FPUF6 decreased by 46%, 69%, 27% and 43.5%, respectively. Moreover, the tensile and compression strength of FPUF6 demonstrated a 52% and 130% increment, respectively. The superior dual metal catalytical charring-forming effect and physical barrier effect of ZIF-8@Ti₃C₂T_x were achieved. In summary, a simple and reliable strategy for preparing flame-retardant FPUF with reinforced mechanical and fire safety properties was provided.

Nickel Manganite-Sodium Alginate Nano-Biocomposite for Temperature Sensing

Nanocrystalline nickel manganite (NiMn2O4) powder with a pure cubic spinel phase structure was synthesized via sol-gel combustion and characterized with XRD, FT-IR, XPS and SEM. The powder was mixed with sodium alginate gel to form a nano-biocomposite gel, dried at room temperature to form a thick film and characterized with FT-IR and SEM. DC resistance and AC impedance of sensor test structures obtained by drop casting the nano-biocomposite gel onto test interdigitated PdAg electrodes on an alumina substrate were measured in the temperature range of 20–50 °C at a constant relative humidity (RH) of 50% and at room temperature (25 °C) in the RH range of 40–90%. The material constant obtained from the measured decrease in resistance with temperature was determined to be 4523 K, while the temperature sensitivity at room temperature (25 °C) was −5.09%/K. Analysis of the complex impedance plots showed a dominant influence of grains. The decrease in complex impedance with increase in temperature confirmed the negative temperature coefficient effect. The grain resistance and grain relaxation frequency were determined using an equivalent circuit. The activation energy for conduction was determined as 0.45 eV from the temperature dependence of the grain resistance according to the small polaron hopping model, while the activation energy for relaxation was 0.43 eV determined from the Arrhenius dependence of the grain relaxation frequency on temperature.

Zinc Oxide Nanoparticles for Water Purification

In this study, zinc oxide nanoparticles were synthesized through a simple co-precipitation method starting from zinc acetate dihydrate and sodium hydroxide as reactants. The as-obtained ZnO nanoparticles were morphologically and structurally characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), photocatalytic activity, and by determining the antimicrobial activity against Gram-negative and Gram-positive bacteria. The XRD pattern of the zinc oxide nanoparticles showed the wurtzite hexagonal structure, and its purity highlighted that the crystallinity correlated with the presence of a single product, zinc oxide. The ZnO nanoparticles have an average crystallite size of 19 ± 11 nm, which is in accordance with the microscopic data. ZnO nanoparticles were tested against methyl orange, used as a model pollutant, and it was found that they exhibit strong photocatalytic activity against this dye. The antibacterial activity of ZnO nanoparticles was tested against Gram-negative and Gram-positive strains (Escherichia coli, Staphylococcus aureus, and Candida albicans). The strongest activity was found against Gram-positive bacteria (S. aureus).

Facile Synthesis and Characterization of Palm CNF-ZnO Nanocomposites with Antibacterial and Reinforcing Properties

Cellulose nanofibers (CNF) isolated from plant biomass have attracted considerable interests in polymer engineering. The limitations associated with CNF-based nanocomposites are often linked to the time-consuming preparation methods and lack of desired surface functionalities. Herein, we demonstrate the feasibility of preparing a multifunctional CNF-zinc oxide (CNF-ZnO) nanocomposite with dual antibacterial and reinforcing properties via a facile and efficient ultrasound route. We characterized and examined the antibacterial and mechanical reinforcement performances of our ultrasonically induced nanocomposite. Based on our electron microscopy analyses, the ZnO deposited onto the nanofibrous network had a flake-like morphology with particle sizes ranging between 21 to 34 nm. pH levels between 8-10 led to the formation of ultrafine ZnO particles with a uniform size distribution. The resultant CNF-ZnO composite showed improved thermal stability compared to pure CNF. The composite showed potent inhibitory activities against Gram-positive (methicillin-resistant Staphylococcus aureus (MRSA)) and Gram-negative Salmonella typhi (S. typhi) bacteria. A CNF-ZnO-reinforced natural rubber (NR/CNF-ZnO) composite film, which was produced via latex mixing and casting methods, exhibited up to 42% improvement in tensile strength compared with the neat NR. The findings of this study suggest that ultrasonically-synthesized palm CNF-ZnO nanocomposites could find potential applications in the biomedical field and in the development of high strength rubber composites.

Synthesis of gold nanoparticles/polyaniline boronic acid/sodium alginate aqueous nanocomposite based on chemical oxidative polymerization for biological applications

Gold nanoparticles/polyaniline boronic acid/sodium alginate aqueous nanocomposite ((PABA-SAL)@AuNPs) was fabricated. Aniline boronic acid (ABA) served as reductant of gold salt, all within the SAL solution. While ABA reduced gold salt to its nanoparticles, the ABA monomer was also oxidized to its conducting polymeric form (PABA). The presence of PABA in the reaction mixture exerted solubility and stability challenge, thus SAL was used as stabilizer and solubilizer for PABA. The numerous cis-diol groups of SAL could bind to boronic acid groups of PABA to furnish PABA-SAL repeating polymer structure for AuNPs anchoring. Sparkling ruby red (PABA-SAL)@AuNPs have absorption peaks at 529 and 718 nm. Average particle sizes of nanocomposite were within 15-20 nm, with hydrodynamic diameter of 48.6 ± 0.9 nm, zeta potential of -32.5 ± 1.6 mV and conductivity value of 2015.3 ± 3.2 μS/cm. (PABA-SAL)@AuNPs possessed antibacterial activities against seafood associated bacterial isolates, with MIC and MBC ranging from 4 to 8 μg/mL. The moderate antioxidant capacity of (PABA-SAL)@AuNPs was observed, without any deleterious damages on human red blood cells. It also has good biocompatibility on Caco-2 and RAW 264.7, with cell viability not less than 70%. These results confirm the high prospect of (PABA-SAL)@AuNPs for possible biomedical applications.

Imminent antimicrobial bioink deploying cellulose, alginate, EPS and synthetic polymers for 3D bioprinting of tissue constructs

3D printing, one of its kinds has been a recent technological trend to fabricate complex and patterned biomaterial with controlled precision. With the conventional kick-start of printing metals and plastics, advancements in printing viable cells, polysaccharides or microbes themselves have been achieved. The additive antimicrobial properties in bioinks sourced from organic and inorganic materials have profound implications in tissue engineering. Cellulose, alginate, exopolysaccharides, ceramics and synthetic polymers are integrated as a viable component in inks and used for bio-printing. To date, bacterial infection and immunogenicity pose a potential health risk during a tissue implant or bone substitution. In order to mitigate microbial infection, antimicrobial bioinks with significant antimicrobial potential have been the much sought after strategies. This approach could be an effective frontline defense against microbial interference in tissue engineering and biomedical applications. An overview on the antimicrobial potential of polysaccharides as bioinks for 3D bioprinting has been critically reviewed.

Antibacterial properties and mechanism of biopolymer-based films functionalized by CuO/ZnO nanoparticles against Escherichia coli and Staphylococcus aureus

In this study, the nanocomposite film (SA-CS@CuO/ZnO) composed of sodium alginate (SA) and chitosan (CS) functionalized by copper oxide nanoparticles (CuONPs) and zinc oxide nanoparticles (ZnONPs) was fabricated, then its antibacterial mechanisms against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) were systematically investigated. When the contents of CuONPs and ZnONPs reached 1.5 % (w/w) and 0.5 % (w/w), respectively, the SA-CS@CuO/ZnO exhibited great mechanical, barrier, and optical properties. Moreover, the incorporation of ZnONPs enhanced the photocatalytic ability of SA-CS@CuO/ZnO, producing a high level of reactive oxygen species under light irradiation. Further, antibacterial results showed that SA-CS@CuO/ZnO treatment inhibited the growth of E. coli and S. aureus higher than 60 % in the dark and exceeded 90 % under light irradiation. This was also manifested in the incompleteness of bacterial cell structure, accompanied by unstable cellular redox balance and DNA disruption. The functions of differentially expressed genes screened by transcriptome analysis were mainly involved in membrane transport, cell wall and membrane synthesis, cellular antioxidant defense system, cell membrane and DNA repair system. The changes in bacterial transcriptional regulation reflected the disturbance in the physiological activities and loss of cell integrity, leading to damage of bacterial cells or death.

Alginate-gum acacia based sponges as potential wound dressings for exuding and bleeding wounds

The improper management of wound exudates can expose the wound to bacterial invasion, skin maceration etc. thereby resulting in prolonged wound healing. Biopolymers are characterized by hydrophilic functional groups which when employed for the development of wound dressings promote the wound dressings capability to absorb a high amount of wound exudates. Alginate-gum acacia sponges were prepared from a combination of biopolymers such as sodium alginate and gum acacia in varying amounts with carbopol via crosslinking with 1 and 2% CaCl₂. The prepared sponges were loaded with a combination of ampicillin and norfloxacin. In vitro antibacterial analysis revealed that the antibacterial activity of the loaded antibiotics was retained and the sponges were effective against gram-positive and gram-negative bacteria. The sponges displayed rapid and high absorption capability in the range of 1022-2419% at pH 5.5 simulating wound exudates, and 2268-5042% at pH 7.4 simulating blood within a period of 1-3 h. Furthermore, the whole blood clotting studies further revealed low absorbance values when compared to the control revealing the good clotting capability of the sponges. The unique features of the sponges revealed their potential application for the management of infected, high exuding and bleeding wounds.

Novel alginate-cellulose nanofiber-poly(vinyl alcohol) hydrogels for carrying and delivering nitrogen, phosphorus and potassium chemicals

Novel nanocomposite hydrogels were successfully prepared by blending and crosslinking sodium alginate (SA), poly(vinyl alcohol) (PVA) and cellulose nanofibers (CNFs) in the presence of a fertilizer formulation containing nitrogen (N), phosphorus (P) and potassium (K). The hydrogels had a macroporous flexible core and a microporous semi- interpenetrating polymer network (IPN) shell. The crystalline nature of the NPK chemicals was retained in the hydrogel nanocomposite network. Furthermore, the SA/CNF/PVA-based hydrogels showed a higher water-retention capacity in both deionized water and mixed soil. The swelling behavior in various physiological pH, salt and alkali solutions exhibited good sensitivity. The NPK release from SA/CNF/NPK and SA/CNF/PVA/NPK hydrogels was controlled by Fickian diffusion in both water and soil based on the Korsmeyer-Peppas release kinetics model (n < 0.5). Therefore, the prepared hydrogels have the potential for applications in drought-prone and/or fertilizer-loss regions for future development of precision agriculture and horticulture.

Nanocomposites derived from licorice residues cellulose nanofibril and chitosan nanofibril: Effects of chitosan nanofibril dosage on resultant properties

Research on nanocomposite film from natural polymers such as cellulose and chitosan is of great importance to promote the development and highly efficient utilization of green and renewable bioresources. In this study, enzymatic pretreatment cellulose nanofibril (ETCNF) derived from licorice residues was prepared, and further processed into nanocomposite film with addition of chitosan nanofibril (CHN). This study focused on the effects of CHN dosage on the main properties of resultant nanocomposite film in terms of crystallinity, thermal stability, light transmittance, hydrophobicity, mechanical properties, and antibacterial activity. The results showed that ETCNF/CHN nanocomposite film exhibited good hydrophobicity especially at higher dosage of CHN, good light transmittance and mechanical properties (tensile strain can reach 39.6 MPa for ETCNF/CHN-10.0%). The as-prepared ETCNF/CHN nanocomposite film also showed good antibacterial activity against Escherichia coli. It was expected that the ETCNF/CHN nanocomposite film would help to realize transformation and high value-added utilization of these biomass residues.

Disinfection by-products in drinking water: Occurrence, toxicity and abatement

Disinfection means the killing of pathogenic organisms (e.g. bacteria and its spores, viruses, protozoa and their cysts, worms, and larvae) present in water to make it potable for other domestic works. The substances used in the disinfection of water are known as disinfectants. At municipal level, chlorine (Cl₂), chloramines (NH₂Cl, NHCl₂), chlorine dioxide (ClO₂), ozone (O₃) and ultraviolet (UV) radiations, are the most commonly used disinfectants. Chlorination, because of its removal efficiency and cost effectiveness, has been widely used as method of disinfection of water. But, disinfection process may add several kinds of disinfection by-products (DBPs) (∼600-700 in numbers) in the treated water such as Trihalomethanes (THM), Haloacetic acids (HAA) etc. which are detrimental to the human beings in terms of cytotoxicity, mutagenicity, teratogenicity and carcinogenicity. In water, THMs and HAAs were observed in the range from 0.138 to 458 μg/L and 0.16-136 μg/L, respectively. Thus, several regulations have been specified by world authorities like WHO, USEPA and Bureau of Indian Standard to protect human health. Some techniques have also been developed to remove the DBPs as well as their precursors from the water. The popular techniques of DBPs removals are adsorption, advance oxidation process, coagulation, membrane based filtration, combined approaches etc. The efficiency of adsorption technique was found up to 90% for DBP removal from the water.

RETRACTED: A review on biomacromolecular hydrogel classification and its applications

This article has been retracted: please see Elsevier Policy on Article Withdrawal (https://www.elsevier.com/locate/withdrawalpolicy). This article has been retracted at the request of the Editor-in-Chief and Author. The work included substantial parts copied without attribution from a prior work by Varaprasad et al (2017): https://doi.org/10.1016/j.msec.2017.05.096

An Overview of Biopolymeric Electrospun Nanofibers Based on Polysaccharides for Wound Healing Management

Currently, despite the thoroughgoing scientific research carried out in the area of wound healing management, the treatment of skin injuries, regardless of etiology remains a big provocation for health care professionals. An optimal wound dressing should be nontoxic, non-adherent, non-allergenic, should also maintain a humid medium at the wound interfacing, and be easily removed without trauma. For the development of functional and bioactive dressings, they must meet different conditions such as: The ability to remove excess exudates, to allow gaseous interchange, to behave as a barrier to microbes and to external physical or chemical aggressions, and at the same time to have the capacity of promoting the process of healing by stimulating other intricate processes such as differentiation, cell adhesion, and proliferation. Over the past several years, various types of wound dressings including hydrogels, hydrocolloids, films, foams, sponges, and micro/nanofibers have been formulated, and among them, the electrospun nanofibrous mats received an increased interest from researchers due to the numerous advantages and their intrinsic properties. The drug-embedded nanofibers are the potential candidates for wound dressing application by virtue of: Superior surface area-to volume ratio, enormous porosity (can allow oxy-permeability) or reticular nano-porosity (can inhibit the microorganisms'adhesion), structural similitude to the skin extracellular matrix, and progressive electrospinning methodology, which promotes a prolonged drug release. The reason that we chose to review the formulation of electrospun nanofibers based on polysaccharides as dressings useful in wound healing was based on the ever-growing research in this field, research that highlighted many advantages of the nanofibrillary network, but also a marked versatility in terms of numerous active substances that can be incorporated for rapid and infection-free tissue regeneration. In this review, we have extensively discussed the recent advancements performed on electrospun nanofibers (eNFs) formulation methodology as wound dressings, and we focused as well on the entrapment of different active biomolecules that have been incorporated on polysaccharides-based nanofibers, highlighting those bioagents capable of improving the healing process. In addition, in vivo tests performed to support their increased efficacy were also listed, and the advantages of the polysaccharide nanofiber-based wound dressings compared to the traditional ones were emphasized.