Hydrothermal treatment of chestnut shells (Castanea sativa) to produce oligosaccharides and antioxidant compounds

Integral Valorization of Posidonia oceanica Balls: An Abundant and Potential Biomass

Posidonia oceanica balls (POB), a kind of seagrass, are a significant environmental issue since they are annually discharged onto beaches. Their current usefulness limits interest in their management and enhances the environmental problem. Therefore, in this research, the potential of this lignocellulosic biomass was studied from a holistic biorefinery point of view. To this end, an in-depth study was carried out to select the best pathway for the integral valorization of POBs. First, an autohydrolysis process was studied for the recovery of oligosaccharides. Then, a delignification stage was applied, where, in addition to studying different delignification methods, the influence of the autohydrolysis pre-treatment was also investigated. Finally, cellulose nanofibers (CNFs) were obtained through a chemo-mechanical treatment. The results showed that autohydrolysis not only improved the delignification process and its products, but also allowed the hemicelluloses to be valorized. Acetoformosolv delignification proved to be the most successful in terms of lignin and cellulose properties. However, alkaline delignification was able to extract the highest amount of lignin with low purity. CNFs were also successfully produced from bleached solids. Therefore, the potential of POB as a feedstock for a biorefinery was confirmed, and the pathway should be chosen according to the requirements of the desired end products.

A circular biorefinery approach for the production of xylooligosaccharides by using mild acid hydrothermal pretreatment of pineapple leaves waste

A hydrothermal process is a sustainable approach for biorefinery leading to conversion of lignocellulosic (LC) biomass into value-added products. This study is based on the production of xylooligosaccharides (XOS) from pineapple leaves (PL) waste by using mild acid like gluconic acid (GA). GA, when used as catalyst in hydrothermal process to produce XOS the yield improved. The above process can be integrated with bacterial cellulose (BC) production bioprocess via Komagataeibacter europaeus 14,148 where gluconic acid is produced as by-product. Maximum XOS (2-5 degree of polymerisation) yield of 67.79 % in the liquid fraction was obtained via hydrothermal treatment at 160 °C for 60 min with 5% gluconic acid concentration. It is based on the selective solubilization of hemicellulose fraction. Enzymatic hydrolysis of GA hydrothermally pretreated solid fraction of PL biomass gave 14.5 g/L glucose with 5% solid loading and 10 FPU/gds enzyme loading which was employed for Bacterial cellulose production.

Production, Characterization and Prebiotic Potential of Xylooligosaccharides Produced from Wheat Bran using Enterobacter hormaechei KS1 Xylanase

In the present investigation, xylooligosaccharides were produced from wheat bran and wheat bran extracted xylan through enzymatic hydrolysis using xylanase from novel Enterobacter hormaechei KS1. Xylooligosaccharides/reducing sugars production from wheat bran was found maximum (374 mg/g) when 4.0% of wheat bran was treated with 375 units (IU/mL) of Enterobacter hormaechei KS1 xylanase at pH 6.0 and incubated at 50 °C for 24 h of incubation. In case of wheat bran extracted xylan 419 mg/g of xylooligosaccharides were produced when 3% of extracted xylan was incubate for 8 h. Analysis of the enzymatic hydrolysate through high performance liquid chromatography equipped with refractive index detector showed the presence of xylose, xylopentose and xylohexose. The decrease in pH with 1.0% dose of xylooligosacchaides produced from extracted xylan hydrolysis using E. hormaechei KS1 xylanase showed more decrease with L. rhamnosus (6.72 to 5.94) followed by L. brevis (6.71 to 6.15) and L. plantarum (6.71 to 6.41). In case of increase in optical density both wheat bran and wheat bran extracted xylan generated xylooligosaccharides exhibited similar pattern i.e., L. rhamnosus > L. plantarum > L. brevis.

Structural elucidation of hemicelluloses from oil-tea camellia fruit shell

Oil-tea camellia fruit shell (CFS) is a very abundant waste lignocellulosic resource. The current treatments of CFS, i.e. composting and burning, pose a severe threat on environment. Up to 50 % of the dry mass of CFS is composed of hemicelluloses. However, chemical structures of the hemicelluloses in CFS have not been extensively studied, which limits their high-value utilization. In this study, different types of hemicelluloses were isolated from CFS through alkali fractionation with the assistance of Ba(OH)2 and H3BO3. Xylan, galacto-glucomannan and xyloglucan were found to be the major hemicelluloses in CFS. Through methylation, HSQC and HMBC analyses, we have found that the xylan in CFS is composed of →4)-β-D-Xylp-(1→ and →3,4)-β-D-Xylp-(1→ linked by (1→4)-β glycosidic bond as the main chain; the side chains are α-L-Fucp-(1→, →5)-α-L-Araf-(1→, β-D-Xylp-(1→, α-L-Rhap-(1→ and 4-O-Me-α-D-GlcpA-(1→, connected to the main chain through (1→3) glycosidic bond. The main chain of galacto-glucomannan in CFS consists of →6)-β-D-Glcp-(1→, →4)-β-D-Glcp-(1→, →4,6)-β-D-Glcp-(1→ and →4)-β-D-Manp-(1→; the side chains are β-D-Glcp-(1→, →2)-β-D-Galp-(1→, β-D-Manp-(1→ and →6)-β-D-Galp-(1→ connected to the main chain through (1→6) glycosidic bonds. Moreover, galactose residues are connected by α-L-Fucp-(1→. The main chain of xyloglucan is composed of →4)-β-D-Glcp-(1→, →4,6)-β-D-Glcp-(1→ and →6)-β-D-Glcp-(1→; the side groups, i.e. β-D-Xylp-(1→ and →4)-β-D-Xylp-(1→, are connected to the main chain by (1→6) glycosidic bond; →2)-β-D-Galp-(1→ and α-L-Fucp-(1→ can also connect to →4)-β-D-Xylp-(1→ forming di- or trisaccharide side chains.

Microwave-assisted autohydrolysis of avocado seed for the recovery of antioxidant phenolics and glucose

This study describes the valorization of avocado seed (AS) within a green biorefinery concept using microwave-assisted autohydrolysis. After the treatment at temperatures of 150-230 °C for 5 min, the resulting solid and liquor were characterized. The temperature of 220 °C led to the simultaneous optimal values of antioxidant phenolics/flavonoids (42.15 mg GAE/g AS, 31, 89 RE/g AS, respectively) and glucose + glucooligosaccharides (38.82 g/L) in the liquor. Extraction with ethyl acetate allowed the recovery of the bioactive compounds while maintaining the polysaccharides in the liquor. The extract was rich in vanillin (99.02 mg/g AS) and contained several phenolic acids and flavonoids. The solid phase and the phenolic-free liquor were subjected to enzymatic hydrolysis to produce glucose, reaching values of 9.93 and 105 g glucose/L, respectively. This work demonstrates that microwave-assisted autohydrolysis is a promising technology to obtain fermentable sugars and antioxidant phenolic compounds from avocado seeds following a biorefinery scheme.

Structural and Physicochemical Properties of Starch from Rejected Chestnut: Hydrothermal and High-Pressure Processing Dependence

The quality standards for the export of chestnuts generate large quantities of rejected fruits, which require novel processing technologies for their safe industrial utilization. This study aimed to investigate the impact of high-pressure processing (HPP) and hydrothermal treatments (HT) on the physicochemical properties of rejected chestnut starch. Chestnuts were treated by HPP at 400, 500, and 600 MPa for 5 min and HT at 50 °C for 45 min. In general, all HPP treatments did not induce starch gelatinization, and their granules preserved the integrity and Maltese-cross. Moreover, starch granules' size and resistant starch content increased with the intensity of pressure. Native and HT chestnut starches were the most susceptible to digestion. HPP treatments did not affect the C-type crystalline pattern of native starch, but the crystalline region was gradually modified to become amorphous. HPP-600 MPa treated starch showed modified pasting properties and exhibited the highest values of peak viscosity. This study demonstrates for the first time that after HPP-600 MPa treatment, a novel chestnut starch gel structure is obtained. Moreover, HPP treatments could increase the slow-digesting starch, which benefits the development of healthier products. HPP can be considered an interesting technology to obtain added-value starch from rejected chestnut fruits.

Analysis of carbohydrates and glycoconjugates by matrix-assisted laser desorption/ionization mass spectrometry: An update for 2017-2018

This review is the tenth update of the original article published in 1999 on the application of matrix-assisted laser desorption/ionization mass spectrometry (MALDI) mass spectrometry to the analysis of carbohydrates and glycoconjugates and brings coverage of the literature to the end of 2018. Also included are papers that describe methods appropriate to glycan and glycoprotein analysis by MALDI, such as sample preparation techniques, even though the ionization method is not MALDI. Topics covered in the first part of the review include general aspects such as theory of the MALDI process, new methods, matrices, derivatization, MALDI imaging, fragmentation and the use of arrays. The second part of the review is devoted to applications to various structural types such as oligo- and poly-saccharides, glycoproteins, glycolipids, glycosides, and biopharmaceuticals. Most of the applications are presented in tabular form. The third part of the review covers medical and industrial applications of the technique, studies of enzyme reactions, and applications to chemical synthesis. The reported work shows increasing use of combined new techniques such as ion mobility and highlights the impact that MALDI imaging is having across a range of diciplines. MALDI is still an ideal technique for carbohydrate analysis and advancements in the technique and the range of applications continue steady progress.

A Joint Approach of Morphological and UHPLC-HRMS Analyses to Throw Light on the Autochthonous 'Verdole' Chestnut for Nutraceutical Innovation of Its Waste

Nowadays, chestnut by-products are gaining a lot of interest as a low-cost raw material, exploitable for developing added-value products. This is in line with suitable chestnut by-products' management, aimed at reducing the environmental impact, thus improving the chestnut industry's competitiveness and economic sustainability. In this context, with the aim of valorizing local cultivars of European chestnuts (Castanea sativa Mill.), our attention focused on the Verdole cultivar, which has been characterized by using the UPOV guidelines for its distinctness, homogeneity, and stability. After harvesting, Verdole chestnuts were properly dissected to collect the outer and inner shells, and episperm. Each chestnut part, previously crushed, shredded, and passed through diverse sieves, underwent ultrasound-assisted extraction. The extracts obtained were evaluated for their total phenolic, flavonoid, and tannin content. The antiradical capacity by DPPH and ABTS assays, and the Fe(III) reducing power, were also evaluated. Although all the samples showed dose-dependent antioxidant efficacy, plant matrix size strongly impacted on extraction efficiency. LC-HRMS-based metabolic profiling highlighted the occurrence of different polyphenol subclasses, whose quantitative ratio varied among the chestnut parts investigated. The outer shell was more chemically rich than inner shell and episperm, according to its pronounced antioxidant activity. The polyphenol diversity of Verdole by-products is a resource not intended for disposal, appliable in the nutraceutical sector, thus realizing a new scenario in processing chestnut waste.

Castanea sativa Mill. Leaf: UHPLC-HR MS/MS Analysis and Effects on In Vitro Rumen Fermentation and Methanogenesis

Castanea sativa Mill. (Fagaceae) is a deciduous tree grown for its wood and edible fruits. Chestnut processing produces residues (burs, shells, and leaves) exploitable for their diversity in bioactive compounds in animal nutrition. In fact, plant-specialized metabolites likely act as rumen modifiers. Thus, the recovery of residual plant parts as feed ingredients is an evaluable strategy. In this context, European chestnut leaves from northern Germany have been investigated, proving to be a good source of flavonoids as well as gallo- and ellagitannins. To this purpose, an alcoholic extract was obtained and an untargeted profiling carried out, mainly by means of ultra-high-performance liquid chromatography/high-resolution tandem mass spectrometry (UHPLC-HR MS/MS) techniques. To better unravel the polyphenol constituents, fractionation strategies were employed to obtain a lipophilic fraction and a polar one. This latter was highly responsive to total phenolic and flavonoid content analyses, as well as to antiradical (DPPH^● and ABTS^+●) and reducing activity (PFRAP) assays. The effect of the alcoholic extract and its fractions on rumen liquor was also evaluated in vitro in terms of fermentative parameter changes and impact on methanogenesis. The data acquired confirm that chestnut leaf extract and the fractions therefrom promote an increase in total volatile fatty acids, while decreasing acetate/propionate ratio and CH₄ production.

Potential Use of Grape Stems and Pomaces from Two Red Grapevine Cultivars as Source of Oligosaccharides

Grape pomace (grape skin and seeds) and stems are major by-products of winemaking, of lignocellulosic nature. The aim of this study was to value grape pomace and stems to produce prebiotic oligosaccharides (OS). Grapes from Touriga Nacional and Marselan cultivars (Vitis vinifera L.) were used for conventional red winemaking. The total of extractives, obtained by sequential extraction with dichloromethane, ethanol, and water, was approx. 64.0% (d.w.) for both pomaces, and 46.2% and 59.5% for Marselan and Touriga Nacional stems, respectively. Lignin contents in Marselan stems (26.4%) and pomace (20.4%) were higher than in Touriga Nacional pomace (19.3%) or stems (17.3%). Polysaccharides (hemicelluloses and cellulose) represented 9 and 8.2% of Marselan and Touriga pomaces, and 22.3 and 18.7% of respective stems. After extractives removal, the pomaces and stems were submitted to a hydrothermal treatment (autohydrolysis) to release oligosaccharides from the hemicellulose fraction. Autohydrolysis was carried out following a central composite rotatable design (CCRD) as a function of temperature (142–198 °C) and time (48–132 min). For all materials of both varieties, the production of sugars by autohydrolysis could be described by second-order models. Highest sugar productions were: 81.2 g/kg (d.w.) extracted Marselan pomace; 76.3 g/kg (d.w.) extracted Touriga Nacional pomace; 116.3 g/kg (d.w.) extracted Marselan stems; and 168.4 g/kg (d.w.) extracted Touriga Nacional stems. Yields of 99% OS were obtained by autohydrolysis at 170 °C/90 min.

Preparation and nutritional properties of xylooligosaccharide from agricultural and forestry byproducts: A comprehensive review

Xylooligosaccharide (XOS) are functional oligosaccharides with prebiotic activities, which originate from lignocellulosic biomass and have attracted extensive attention from scholars in recent years. This paper summarizes the strategies used in the production of XOS, and introduces the raw materials, preparation methods, and purification technology of XOS. In addition, the biological characteristics and applications of XOS are also presented. The most commonly recommended XOS production strategy is the two-stage method of alkaline pre-treatment and enzymatic hydrolysis; and further purification by membrane filtration to achieve the high yield of XOS is required for prebiotic function. At the same time, new strategies and technologies such as the hydrothermal and steam explosion have been used as pre-treatment methods combined with enzymatic hydrolysis to prepare XOS. XOS have many critical physiological activities, especially in regulating blood glucose, reducing blood lipid, and improving the structure of host intestinal flora.

Bioactive Antioxidant Compounds from Chestnut Peels through Semi-Industrial Subcritical Water Extraction

Chestnut peels are a poorly characterized, underexploited by-product of the agri-food industry. This raw material is rich in bioactive compounds, primarily polyphenols and tannins, that can be extracted using different green technologies. Scaling up the process for industrial production is a fundamental step for the valorization of the extract. In this study, subcritical water extraction was investigated to maximize the extraction yield and polyphenol content. Lab-scale procedures have been scaled up to the semi-industrial level as well as the downstream processes, namely, concentration and spray drying. The extract antioxidant capacity was tested using in vitro and cellular assays as well as a preliminary evaluation of its antiadipogenic activity. The temperature, extraction time, and water/solid ratio were optimized, and the extract obtained under these conditions displayed a strong antioxidant capacity both in in vitro and cellular tests. Encouraging data on the adipocyte model showed the influence of chestnut extracts on adipocyte maturation and the consequent potential antiadipogenic activity. Chestnut peel extracts characterized by strong antioxidant power and potential antiadipogenic activity were efficiently obtained by removing organic solvents. These results prompted further studies on fraction enrichment by ultra- and nanofiltration. The semi-industrial eco-friendly extraction process and downstream benefits reported here may open the door to production and commercialization.

Integral valorisation of walnut shells based on a three-step sequential delignification

Walnut kernels represent no more than 50-60% of the total weight of the fruit, so the sum of walnut shells generated every year is immense. Nonetheless, these shells could be further valorised for the extraction of their main constituents following a biorefinery scheme. Hence, the objective of this work was an integral valorisation of walnut shells, which involved a sequential organosolv delignification (200 °C, 90 min, 70/30 v/v EtOH/H₂O, LSR 6:1) and several posterior non-isothermal hydrothermal treatments (180, 195 and 210 °C, LSR 8:1). Moreover, the spent solids after the aforementioned treatments were evaluated as possible sources of cellulose nanocrystals. The results showed that the sequential organosolv delignifications presented relative lignin yields up to 60%, which leaded to lignins that just differed on their molecular weight distributions. The hydrothermal treatments were efficient for the removal of still present hemicelluloses (14.7-71.8%), and permitted a successful cellulose nanocrystal obtaining whereas the spent solid from the delignification stages did not. Thus, this study presented an innovative strategy for the integral valorisation of walnut shells.

Energy-efficient glucose recovery from chestnut shell by optimization of NaOH pretreatment at room temperature and application to bioethanol production

Biofuel policies are currently being implemented globally to reduce greenhouse gas emissions. The recent European regulation, Renewable Energy Directive (RED) II, states that renewable resources should be used as raw materials. In this study, chestnut shell (CNS), a food processing residue, was utilized as a feedstock for bioethanol production. Statistical optimization was performed to improve biomass-to-glucose conversion (BtG) from the CNS. In order to design an energy-efficient process, the pretreatment was fixed at room temperature in the numerical optimization. The optimal conditions derived from the predicted model are as follows: temperature of 25 °C, reaction time of 2.8 h, and NaOH concentration of 1.9% (w/w). Under optimal conditions, both predicted and experimental BtG were 31.0%, while BtG was approximately 3.3-fold improved compared to the control group (without pretreatment). The recovered glucose was utilized for bioethanol fermentation by Saccharomyces cerevisiae K35 and the ethanol yield was achieved to be 98%. Finally, according to the mass balance based on 1000 g CNS, glucose of 310 g can be recovered by the pretreatment; the bioethanol production was approximately 155 g. This strategy suggests a direction to utilize CNS as a potential feedstock for biorefinery through the design of an economical and energy-efficient pretreatment process by lowering the reaction temperature to room temperature.

Preparation, structural characterization and prebiotic potential of mulberry leaf oligosaccharides

The present study shows the purification of a main oligosaccharide fraction (MLO 1-2) from the enzymatic hydrolysate of mulberry leaf polysaccharides by DEAE-52 cellulose and gel column chromatography. The physicochemical properties of MLO 1-2 were characterized. The structure of MLO 1-2 was obtained as follows: α-(2-OAc)-Manp-1 → 2-β-Glcp-1 → 4-β-Glcp-1 → 4-α-Glcp-1 → 2-α-Glcp-1 → 2-α-Galp-1 → 2-β-Galp-1 → 2-β-Galp-1, which was elucidated by methylation and NMR analysis. The molecular weight of MLO 1-2 showed no significant change after simulated saliva, gastric and intestinal digestion. This indicated that MLO 1-2 could pass through the digestive system without being degraded to safely reach the colon to regulate the gut microbiota. Additionally, MLO 1-2, more than glucose or galactooligosaccharides, promoted the proliferation of Bifidobacterium bifidum, B. adolescentis, Lacticaseibacillus rhamnosus and Lactobacillus acidophilus. Furthermore, the acetic and lactic acid concentrations of bacterial cultures inoculated with MLO 1-2 were higher than those inoculated with glucose and galactooligosaccharide (GOS). These results suggest that MLO 1-2 could be an excellent prebiotic for intestinal flora regulation and the promotion of gut health.

Current breakthroughs in the hardwood biorefineries: Hydrothermal processing for the co-production of xylooligosaccharides and bioethanol

The development of lignocellulosic biorefineries requires a first stage of pretreatment which enables the efficient valorization of all fractions present in this renewable material. In this sense, this review aims to show the main advantages of hydrothermal treatment as a first step of a biorefinery infrastructure using hardwood as raw material, as well as, main drawback to overcome. Hydrothermal treatment of hardwood highlights for its high selectivity for hemicelluloses solubilization as xylooligosaccharides (XOS). Nevertheless, the suitable conditions for XOS production are inadequate to achieve an elevate cellulose to glucose conversion. Hence, several strategies namely the combination of hydrothermal treatment with delignification process, in situ modification of lignin and the mixture with another renewable resources (concretely, seaweeds, and by-products generated in the food industry with high sugar content) were pinpointed as promising alternative to increase the final ethanol concentration coupled with XOS recovery in the hydrolysate.

Advances in pretreatment of lignocellulosic biomass for bioenergy production: Challenges and perspectives

As a clean and renewable energy, bioenergy is one of the most promising alternatives to fossil fuels. Lignocellulose possesses great potential for bioenergy production, but the recalcitrant and heterogeneous structure limits its application. Pretreatment technology offers an effective solution to fractionate the main components of the lignocellulose and uncover the available cellulose. The obtained feedstock can be applied to bioconversion into energy, e.g., bioethanol, biogas, biohydrogen, etc. Here, the current state of lignocellulose pretreatment technologies was comprehensively reviewed, the advances in bioenergy production from pretreated lignocellulose was described, with particular attention to key challenges involved. Several new strategies for overcoming pretreatment barriers to realize highly efficient lignocellulose bioconversion were highlighted. The insights given in this review will facilitate further development on lignocellulosic bioenergy production, towards addressing the global energy crisis and climate change related to the use of fossil fuels.

Hydrothermal treatment of avocado peel waste for the simultaneous recovery of oligosaccharides and antioxidant phenolics

Avocado industrial processing generates huge quantities of residues that are currently wasted without any valuable commercial application. This work deals with autohydrolysis of Avocado peel (AP) for the concomitant recovery of oligosaccharides and polyphenolics. Temperature of 150 °C allowed the highest recovery of oligosaccharides (14.3 g oligosaccharides/100 g AP) and high recovery of antioxidant phenolics (3.48 g gallic acid equivalents/100 g AP and 10.80 g Trolox equivalents/100 g AP measured with ABTS^●+ assay). The liquor obtained at this temperature was characterized by TGA and FTIR to study its thermal stability and functional groups. UHPLC-TOF MS analysis of an ethyl acetate extract of AP liquor enabled the tentative identification of 43 compounds, belonging to various metabolite families, including flavonoids, phenolic acids, organic acids, lignans and fatty acids. These findings demonstrated that autohydrolysis of AP is a suitable technology to obtain bioactive agents with potential uses in food and cosmetic industries.

Production of xylooligosaccharides, bioethanol, and lignin from structural components of barley straw pretreated with a steam explosion

Barley straw (BS) is a potential source to obtain bioethanol and value-added products such as xylooligosaccharides (XOS) and lignin for application in diverse industries. In this study, BS was submitted to steam explosion pretreatment to valorize the main components of this lignocellulose biomass. For hemicellulose fraction valorization, different combinations of endo-β-(1,4)-D-xylanase enzyme with accessory enzymes (α-L-arabinofuranosidase, feruloy -esterase and acetylxylan-esterase) have been studied to produce XOS with a low degree of polymerization. The application of accessory enzymes combined with endo-β-(1,4)-D-xylanase enzymes turned out to be the most effective strategy for the formation of XOS. The solid fraction obtained after the pretreatment was submitted to presacharification and simultaneous saccharification and fermentation process for bioethanol production. The resulting lignin-rich residue was characterized. In this integrated process, 13.0 g XOS (DP2-DP6), 12.6 g ethanol and 16.6 g lignin were obtained from 100 g of BS, achieving the goal of valorizing this agricultural residue.

Valorization of Chinese hickory shell as novel sources for the efficient production of xylooligosaccharides

Chinese hickory shell, a by-product of the food industry, is still not utilized and urgent to develop sustainable technologies for its valorization. This research focuses on the systematical evaluation of degraded products and xylooligosaccharide production with high yield from the shell via hydrothermal process. The pretreatment was carried out in a bath pressurized reactor at 140-220 °C for 0.5-2 h. The results indicated that the pretreatment condition strongly affected the chemical structures and compositions of the liquid fraction. The maximum yield of XOS (55.3 wt%) with limitation of by-products formation was achieved at 160 °C for 2 h. High temperature (220 °C) and short time (0.5 h) contributed to hydrolysis of xylooligosaccharide with high DP to yield 37.5 wt% xylooligosaccharide with DP from 2 to 6. Xylooligosaccharide obtained mainly consisted of xylan with branches according to the HSQC NMR analysis. Overall, the production of XOS with a high yield from food waste will facilitate the valorization of food waste in the biorefinery industry.

Microwave hydrothermal processing of the invasive macroalgae Sargassum muticum within a green biorefinery scheme

This study deals with the multiproduct valorization of the invasive macroalgae Sargassum muticum within a green biorefinery concept using microwave hydrothermal treatment. Temperatures of 160 and 180 °C for 0-60 min (severities 1.62-3.54) were evaluated, allowing a recovery of a liquid phase rich in fucoidan-derived compounds (up to 4.81 g/L), oligomers and phenolics with antioxidant capacity (up to 2.85 g TE/L by ABTS assay), and a high-enzymatically susceptible solid (glucan to glucose conversion 76-100% in 9 h) suitable for bioethanol production (20.5 g/L in 18 h, corresponding to 96% ethanol yield). Moreover, energy consumption of the pretreatments' temperature-time binomial was evaluated showing significant differences, demonstrating the advantages of microwave as alternative heating pretreatment.

Identification and Recovery of Valuable Bioactive Compounds from Potato Peels: A Comprehensive Review

Nowadays, the potato is one of the most cultivated and consumed food crops in the world and, in recent years, its production has experienced a sharp increase. Its industrial processing generates several by-products that are wasted and cause economic and environmental problems. Among them, potato peel stands out, representing up to 10% of the total potato residues obtained in the processing. On the other hand, these wastes, in addition to presenting antioxidant compounds, are rich in interesting chemical compounds of great value in a biorefinery model. This review summarizes the main compounds present in potato skins as well as the most used and innovative extraction methods employed for their isolation, with special emphasis on the fractions with biological activities. In addition, a sustainable biorefinery proposal focused on obtaining high added-value products with potential applications in the pharmaceutical, food, nutraceutical, or cosmetic industries is included.

Acid hydrolysis of almond shells in a biphasic reaction system: Obtaining of purified hemicellulosic monosaccharides in a single step

The aim of this work is to comprehend the biphasic reaction systems through another perspective; the simultaneous purification and production of carbohydrates during the pretreatment of biomass. A dilute acid hydrolysis of almond shells in a 2-Methyltetrahydrofuran/H₂O system was optimised to maximise the obtaining of hemicellulose-derived monosaccharides with the minimum formation of degradation products. The optimised conditions of the biphasic reaction system, which produced 205.3 g hemicellulose-derived monosaccharides/Kg almond shells, were replicated in a monophasic reaction system to assess the benefits of the biphasic reaction systems. The latest system allowed the removal of 85.3% of the furans generated during the dilute acid hydrolysis, creating antioxidant extract, together with the catalysis of the hydrolysis of the hemicelluloses in a 20%. Therefore, the proposed process could become a promising method to purify carbohydrates with an environmentally friendly procedure that allowed the obtaining of multiple added-value products in a single step.

Castanea sativa shells: A review on phytochemical composition, bioactivity and waste management approaches for industrial valorization

Castanea sativa is an outstanding species that represents a valuable natural resource for rural populations. C. sativa shells (CSS), an abundant agro-industrial by-product generated during chestnut peeling process, is commonly discarded or used as fuel. Nevertheless, CSS produced are not depleted by this application and huge amounts are still available, being particularly rich in bioactive compounds (polyphenols, vitamin E, lignin and oligosaccharides) with health benefits. Phytochemical studies reported not only antioxidant and antimicrobial activities, but also anti-inflammatory, anticancer, hypolipidemic, hypoglycemic and neuroprotective activities. The application of a suitable extraction technique is required for the isolation of bioactive compounds, being green extraction technologies outstanding for the industrial recovery of chestnut shells' bioactive compounds. CSS were highlighted as remarkable sources of functional ingredients with promising applications in food and nutraceutical fields, mainly as natural antioxidants and effective prebiotics. This review aims to summarize the phytochemical composition and pro-healthy properties of CSS, emphasizing the sustainable extraction techniques employed in the recovery of bioactive compounds and their potential applications in food and nutraceutical industries.

Hydrothermal treatments of walnut shells: A potential pretreatment for subsequent product obtaining

Walnuts are nowadays widely consumed. Since the edible part of walnuts does not account more than 50-60% of their total weight, the total amount of shells produced annually is huge. However, as walnut shells are part of lignocellulosic biomass, they could be valorised via a biorefinery approach in order to extract their diverse constituents. For this reason, the aim of this work was to valorise walnut shells by a biorefinery scheme. The latest involved multiple microwave assisted and conventional hydrothermal treatments for the subsequent valorisation of oligosaccharides. Then, an organosolv delignification of the solid that permitted the maximum oligosaccharide yield was performed, in order to isolate the lignin. Finally, it was treated for cellulose nanocrystal obtaining. The results showed, on the one hand, that the hydrothermal treatments leaded to xyloligossacharide-rich liquors (1-17 g/L). On the other hand, the organosolv delignification resulted into the extraction of a highly pure lignin (93.6%) and a weight average molecular weight of 7000 Da. Moreover, the solid from the delignification treatment was suitable for a successful nanocrystal production. The extracted fractions could be employed in many applications and could be considered renewable precursors for new materials and chemicals. Hence, the proposed biorefinery scheme would allow an integral valorisation of currently undervalued walnut shells.

Improvement of Enzymatic Glucose Conversion from Chestnut Shells through Optimization of KOH Pretreatment

Worldwide, about one-third of food produced for human consumption is wasted, which includes byproducts from food processing, with a significant portion of the waste still being landfilled. The aim of this study is to convert chestnut shells (CNSs) from food processing into a valuable resource through bioprocesses. Currently, one of the highest barriers to bioprocess commercialization is low conversion of sugar from biomass, and KOH pretreatment was suggested to improve enzymatic digestibility (ED) of CNS. KOH concentration of 3% (w/w) was determined as a suitable pretreatment solution by a fundamental experiment. The reaction factors including temperature, time and solid/liquid (S/L) ratio were optimized (77.1 g/L CNS loading at 75 °C for 2.8 h) by response surface methodology (RSM). In the statistical model, temperature and time showed a relatively significant effect on the glucan content (GC) and ED, but S/L ratio was not. GC and ED of the untreated CNS were 45.1% and 12.7%, respectively. On the other hand, GC and ED of pretreated CNS were 83.2% and 48.4%, respectively, and which were significantly improved by about 1.8-fold and 3.8-fold compared to the control group. The improved ED through the optimization is expected to contribute to increasing the value of byproducts generated in food processing.

Environmentally Friendly Hydrothermal Processing of Melon by-Products for the Recovery of Bioactive Pectic-Oligosaccharides

Melon by-products, that currently lack high value-added applications, could be a sustainable source of bioactive compounds such as polysaccharides and antioxidants. In this work, melon peels were extracted with water to remove free sugars, and the water-insoluble solids (WISs) were subjected to hydrothermal processing. The effect of temperature on the composition of the obtained liquors and their total phenolic content was evaluated. The selected liquors were also characterized by matrix assisted laser desorption/ionization-time of flight mass spectroscopy (MALDI-TOF MS), fourier transform infrared spectroscopy (FTIR) and high performance anion exchange chromatography with pulsed amperometric detection (HPAEC-PAD), and its phenolic compounds were identified and quantified by high-performance liquid chromatography-diode array detector-tandem mass spectrometry (HPLC-DAD-MS/MS). In addition, the spent solids from the hydrothermal treatment were characterized and their potential use was assessed. At the optimal conditions of 140 °C (severity 2.03), the total oligosaccharide yield accounted for 15.24 g/100 g WIS, of which 10.07 g/100 g WIS were oligogalacturonides. The structural characterization confirmed the presence of partially methyl esterified oligogalacturonides with a wide range of polymerization degrees. After precipitation, 16.59 g/100 g WIS of pectin were recovered, with a galacturonic acid content of 55.41% and high linearity.

A Whole-Slurry Fermentation Approach to High-Solid Loading for Bioethanol Production from Corn Stover

Corn stover is the most produced byproduct from maize worldwide. Since it is generated as a residue from maize harvesting, it is an inexpensive and interesting crop residue to be used as a feedstock. An ecologically friendly pretreatment such as autohydrolysis was selected for the manufacture of second-generation bioethanol from corn stover via whole-slurry fermentation at high-solid loadings. Temperatures from 200 to 240 °C were set for the autohydrolysis process, and the solid and liquid phases were analyzed. Additionally, the enzymatic susceptibility of the solid phases was assessed to test the suitability of the pretreatment. Afterward, the production of bioethanol from autohydrolyzed corn stover was carried out, mixing the solid with different percentages of the autohydrolysis liquor (25%, 50%, 75%, and 100%) and water (0% of liquor), from a total whole slurry fermentation (saving energy and water in the liquid–solid separation and subsequent washing of the solid phase) to employing water as only liquid medium. In spite of the challenging scenario of using the liquor fraction as liquid phase in the fermentation, values between 32.2 and 41.9 g ethanol/L and ethanol conversions up to 80% were achieved. This work exhibits the feasibility of corn stover for the production of bioethanol via a whole-slurry fermentation process.

Multiproduct biorefinery based on almond shells: Impact of the delignification stage on the manufacture of valuable products

In this work, an integral valorisation of almond shells through a biorefinery approach was studied. The three main components of almond shells were extracted, isolated and characterised. The autohydrolysis process permitted the extraction of the hemicellulosic fraction obtaining a liquor rich in xylooligosaccharides (22.12 g/L). Then, two different delignification processes, alkaline and organosolv treatments, were proposed to obtain a very high purity lignin (≈90%) which could be further valorised for a wide variety of applications. The valorisation of the high cellulosic content of the delignified solids was carried out using two different methods. On the one hand, producing cellulose nanocrystals and on the other hand obtaining glucose by an enzymatic hydrolysis as well as a spent solid mainly composed by lignin (≈78 wt%). Thus, the proposed biorefinery approach could contribute to a circular economy as all the main components of the almond shells could be revalorised by environmentally friendly procedures.

Evaluation of physicochemical properties of Qinling Apis cerana honey and the antimicrobial activity of the extract against Salmonella Typhimurium LT2 in vitro and in vivo

Apis cerana honey collected from the Qinling Mountains in China has been widely used for its antimicrobial property in traditional Chinese medicine. However, its antibacterial mechanism against Salmonella Typhimurium LT₂ is still uncertain. A total of 52 volatile components were identified using headspace-gas-chromatography-ion-mobility, and Qinling A. cerana honey exhibited more abundant aromas than monofloral honeys. The phenolic extracts of honey sample F exhibited the lowest minimum inhibitory concentration (5 mg/mL), and chlorogenic acid exhibited the highest (155.91 ± 0.79 mg/kg), followed by caffeic acid, and rutin. After being treated with the extract, cell membranes of S. Typhimurium LT₂ significantly shrunk and further collapsed. The extract treatment on mice caused a significant decrease in S. Typhimurium LT₂, and a dramatic increase in the potential prebiotic Lactobacillus in both the caecum and colon. The results demonstrate that the Qinling A. cerana honey extract could effectively inhibit S. Typhimurium in vitro and in vivo.

Subcritical Water Extraction of Chestnut Bark and Optimization of Process Parameters

The aim of the work was the optimization of the subcritical water extraction process of chestnut bark using Box–Behnken response surface methodology. The influence of process parameters, such as temperature, extraction time and solvent-solid ratio, on extraction yield, yield of the main compounds, total phenol content, total tannin content and antioxidant activity has been investigated. The identified compounds were ellagic and gallic acids, ellagitannins (vescalagin, castalagin, 1-o-galloyl castalagin, vescalin and castalin), sugars (maltose, glucose, fructose and arabinose) and sugar derivatives (5-HMF, furfural and levulinic acid). Finally, the optimal process conditions for obtaining the bark extract highly rich in ellagic acid and with satisfactory levels of total phenols and total tannins have been determined.

Response surface methodology for the fermentation of polysaccharides from Auricularia auricula using Trichoderma viride and their antioxidant activities

Fermentation technology was used to improve the antioxidant activities of Auricularia auricula polysaccharide (AAP). Response surface methodology (RSM) was used to optimize the fermentation conditions. The effects of 4 independent factors: water content (X₁: 40-80%), inoculation amount (X₂: 2-20%), temperature (X₃: 24-32 °C), and time (X₄: 4-6 d) on the biological degradation efficiency were evaluated. The RSM results showed that the optimal fermentation conditions were: X₁: 61.7%, X₂: 12.4%, X₃: 31.0 °C, X₄: 5.5 d. Verification tests showed no significant differences between the practical and the predictive values for each response. Under the optimal conditions, the degradation rate was 26.89 ± 0.14%, without significant differences with the predicted value (27.03%). The degradation products were classified to different molecular weight (M_w) polysaccharide fragments using membrane separation technology. The FT-IR analysis and monosaccharide composition analysis of degraded AAP (D-AAP-VI) showed that D-AAP-VI was a furan type polysaccharide, which was different from the total AAP (pyran type). In addition, compared to total AAP, the antioxidant activities in vitro of D-AAP-VI were significantly improved (p < 0.05) and D-AAP-VI showed the strongest antioxidant activity. These results indicated that biological degradation may be a suitable way to improve the antioxidant activities of natural polysaccharides.

Green sustainable process to revalorize purple corn cobs within a biorefinery frame: Co-production of bioactive extracts

Purple corn (Zea mays L.) is used for the preparation of traditional drinks and desserts, generating great quantities of residues. The scarce information about purple corn cob (PCC) is encouraging an interest in exploring its potential as a valuable source of bioactive compounds with benefits for human health. In this study, a green method based on hydrothermal processing was used for the simultaneous extraction of oligosaccharides and phenolic compounds from PCC. For this purpose, the effects of three factors (time, temperature and pH) on the oligosaccharide content (OSC), total phenolic content (TPC), total flavonoid content (TFC), total anthocyanin content (TAC), as well as on the antioxidant activity measured with three different methods (DPPH, ABTS and FRAP) were evaluated. The bioactive extract obtained under optimal conditions presented a high content of bioactive compounds exhibiting a notable antioxidant capacity and moderate inhibitory activities towards xanthine oxidase. This extract was also structurally characterized by FTIR, HPAEC-DAD, MALDI-TOF-MS and TGA, and the HPLC-ESI-MS analysis led to the tentative identification of 15 antioxidant phenolic compounds. Thus, this research demonstrated that this residue from the food industry has a high potential for obtaining several bioactive compounds that can be utilized as multi-functional ingredients in the food and pharmaceutical industries.

Production of Oligosaccharides from Agrofood Wastes

The development of biorefinery processes to platform chemicals for most lignocellulosic substrates, results in side processes to intermediates such as oligosaccharides. Agrofood wastes are most amenable to produce such intermediates, in particular, cellooligo-saccharides (COS), pectooligosaccharides (POS), xylooligosaccharides (XOS) and other less abundant oligomers containing mannose, arabinose, galactose and several sugar acids. These compounds show a remarkable bioactivity as prebiotics, elicitors in plants, food complements, healthy coadyuvants in certain therapies and more. They are medium to high added-value compounds with an increasing impact in the pharmaceutical, nutraceutical, cosmetic and food industries. This review is focused on the main production processes: autohydrolysis, acid and basic catalysis and enzymatic saccharification. Autohydrolysis of food residues at 160–190 °C leads to oligomer yields in the 0.06–0.3 g/g dry solid range, while acid hydrolysis of pectin (80–120 °C) or cellulose (45–180 °C) yields up to 0.7 g/g dry polymer. Enzymatic hydrolysis at 40–50 °C of pure polysaccharides results in 0.06–0.35 g/g dry solid (DS), with values in the range 0.08–0.2 g/g DS for original food residues.

Content of Phenolic Compounds and Antioxidant Activity of New Gluten-Free Pasta with the Addition of Chestnut Flour

Chestnut fruit abounds in carbohydrates, proteins, unsaturated fatty acids, fiber, polyphenolic compounds, as well as vitamins and micronutrients, that are behind the health-promoting properties of this plant. The purpose of the discussed research was to obtain innovative gluten-free pasta from rice and field bean flour enriched with a various addition of chestnut flour. Regarding the studied pasta, the following were determined: the content of free phenolic acids, total polyphenols, and antioxidant properties. Chromatographic analysis (HPLC-ESI-MS/MS (high-performance liquid chromatography-electrospray ionization tandem mass spectrometry)) revealed a wide variety of phenolic acids. In a sample with 20% and higher content of chestnut flour, as many as 13 acids were detected. Isoferulic acid prevailed. The total content of free phenolic acids and total polyphenols increased along with the increasing chestnut content. Moreover, in most cases, the content of individual acids increased with the addition of chestnut flour. Besides, the antioxidant activity was positively correlated with the addition of chestnut fruit flour, the content of free phenolic acids, and total polyphenols. Our research has demonstrated that our innovative gluten-free pasta, with the addition of chestnut flour, has a potential to be a source of polyphenolic compounds, including free phenolic acids, that are valuable for human health.

Effect of Steaming Processing on Phenolic Profiles and Cellular Antioxidant Activities of Castanea mollissima

The intention of this study was to investigate the effect of steaming processing on phenolic profiles and antioxidant activities in chestnuts. Steaming processing at different times and temperatures depicted diverse impacts on free and bound fractions. Though, bound phenolics were stable but long time steaming at higher temperatures tended to improve the levels of phenolics, flavonoids as well as antioxidant activities in chestnut kernels, by up to 60.11% of the original value. Seven phenolic compounds including ferulic acid, chlorogenic acid, gallic acid, vanillic acid, syringate, p-coumaric acid and quercetin were found to change during thermal processes. Significant relationships (p < 0.05) were identified between total phenolics and total antioxidant activities. However, the consistency of chlorogenic acid (p < 0.01) only with cellular antioxidant activity indicated poor bio-accessibility of the phytochemicals in chestnuts. However, this situation could be partly improved by steaming. Steaming could improve the cellular accessibility of free phytochemicals, particularly, increasing the bio-accessibility by 41.96%. This study provided valuable information on dynamic changes of phenolic profiles and antioxidant activity of chestnuts under a steaming process, which could offer possible guidance for the chestnut processing industry in the future.