Facile functionalization of cellulose from discarded cigarette butts for the removal of diclofenac from water

Recovery of cellulose acetate bioplastic from cigarette butts: realization of a sustainable sorbent for water remediation

Cigarette butts, one of the most common forms of litter in the world, represent a source of chemical and plastic pollution releasing thousands of toxic compounds and microfibers of cellulose acetate (CA). Besides the correct waste management, the recovery of CA from cigarette filters is a way to cushion their negative effects on the environment. Thus far, recycling strategies have been limited to industrial applications, while not many solutions have designed for water remediation. This work describes a strategy to valorize this harmful waste and to reverse its environmental impact, proposing a simple and effective procedure of reclamation of CA and its reuse to prepare a composite sorbent for the treatment of polluted water. The first step entails the washing of filters with hot water (T = 90 °C) and hot ethanol (T = 58-68 °C) to remove the impurities produced during cigarette burning, as verified by means of UV and attenuated total reflection-Fourier-transform infrared (ATR-FTIR) spectroscopy, thermal gravimetric analysis (TGA), and differential scanning calorimetry (DSC). The second step involves the use of the regenerated CA to prepare porous cylinder-shaped cryogels (15 mm × 10 mm) whose sorption properties are enhanced by the combination with AC (15 % w/w). The synthesis takes advantage of the sol-gel transition of the polymer dispersion (5 % w/V) in a solution acetone/water 5 mM in NH3 (60/40, v/v). After characterization by dynamic mechanical analysis (DMA), TGA, FT-IR, and scanning electron microscopy (SEM), the adsorption capability of the physical cryogel was studied in terms of treated environmental water volume, contact time and concentration of the selected pollutants. The results have shown that the proposed strategy is a low-cost way to recycle CA from cigarette butts and that the designed sorbent is a promising material for water treatment, allowing quick removal times and yields >79.6 %.

Cellulose acetate, a source from discarded cigarette butts for the development of mixed matrix loose nanofiltration membranes for selective separation

This study presents an environmentally friendly method for extracting cellulose acetate (CA) from discarded cigarette filters, which is then utilized in the fabrication of cellulose-based membranes designed for high flux and rejection rates. CA membranes are likeable to separate dyes and ions, but their separation efficiency is exposed when the contaminant concentration is very low. So, we have integrated graphene oxide (GO) and carboxylated titanium dioxide (COOH-TiO2) in CA to develop mixed matrix membranes (MMMs) and studied them against dyes and most used salts. The CA has been extracted from these butts and added GO and COOH-TiO2 nanoparticles to develop MMMs. The present work administers the effective separation of five dyes (methyl orange, methyl violet, methylene blue, cresol red, and malachite green) and salts (NaCl and Na2SO4) along with the high efficiency of water flux by prepared CA membranes. The prepared membranes rejected up to 94.94 % methyl violet, 91.28 % methyl orange, 88.28 % methylene blue, 89.91 % cresol red, and 91.70 % malachite green dye. Along with the dyes, the membranes showed ∼40.40 % and ∼ 42.97 % rejection of NaCl and Na2SO4 salts, respectively. Additionally, these membranes have tensile strength up to 1.54 MPa. Various characterization techniques were performed on all prepared CA membranes to comprehend their behaviour. The antibacterial activity of MMMs was investigated using the Muller-Hinton-Disk diffusion method against the gram-positive bacterium Staphylococcus aureus (S. aureus) and the gram-negative bacterium Escherichia coli (E. coli). We believe the present work is an approach to utilizing waste materials into valuable products for environmental care.

Production of solid acid catalyst using waste cigarette filters for esterification

Cigarette filters were utilized as carbon source for the production of solid carbon acid catalysts. In this study, the process of carbonization and simultaneous sulfonation via hydrothermal treatment was employed. The catalysts were prepared by mixing cigarette filters and sulfuric acid at temperatures of 100, 150, and 190 °C for durations ranging from 2 to 8 h. It was observed that the highest conversion of oleic acid occurred when the catalyst was synthesized at 190 °C for 4 h. The optimized conditions for the esterification reaction using this catalyst included an oleic acid to methanol molar ratio of 1:12, a catalyst loading of 5 wt%, and a temperature of 100 °C for 1 h. Additionally, the catalyst was successfully reused four times without significantly impacting the reaction yield. These findings highlight a promising approach for the utilization of waste materials, with immediate implications for waste management practices and positive environmental impacts.

Recent advances and future perspective on lignocellulose-based materials as adsorbents in diverse water treatment applications

The growing shortage of non-renewable resources and the burden of toxic pollutants in water have gradually become stumbling blocks in the path of sustainable human development. To this end, there has been great interest in finding renewable and environmentally friendly materials to promote environmental sustainability and combat harmful pollutants in wastewater. Of the many options, lignocellulose, as an abundant, biocompatible and renewable material, is the most attractive candidate for water remediation due to the unique physical and chemical properties of its constituents. Herein, we review the latest research advances in lignocellulose-based adsorbents, focusing on lignocellulosic composition, material modification, application of adsorbents. The modification and preparation methods of lignin, cellulose and hemicellulose and their applications in the treatment of diverse contaminated water are systematically and comprehensively presented. Also, the detailed description of the adsorption model, the adsorption mechanism and the adsorbent regeneration technique provides an excellent reference for understanding the underlying adsorption mechanism and the adsorbent recycling. Finally, the challenges and limitations of lignocellulosic adsorbents are evaluated from a practical application perspective, and future developments in the related field are discussed. In summary, this review offers rational insights to develop lignocellulose-based environmentally-friendly reactive materials for the removal of hazardous aquatic contaminants.

Cellulose-based adsorbents for solid phase extraction and recovery of pharmaceutical residues from water

Cellulose has attracted interest from researchers both in academic and industrial sectors due to its unique structural and physicochemical properties. The ease of surface modification of cellulose by the integration of nanomaterials, magnetic components, metal organic frameworks and polymers has made them a promising adsorbent for solid phase extraction of emerging contaminants, including pharmaceutical residues. This review summarizes, compares, and contrasts different types of cellulose-based adsorbents along with their applications in adsorption, extraction and pre-concentration of pharmaceutical residues in water for subsequent analysis. In addition, a comparison in efficiency of cellulose-based adsorbents and other types of adsorbents that have been used for the extraction of pharmaceuticals in water is presented. From our observation, cellulose-based materials have principally been investigated for the adsorption of pharmaceuticals in water. However, this review aims to shift the focus of researchers to the application of these adsorbents in the effective pre-concentration of pharmaceutical pollutants from water at trace concentrations, for quantification. At the end of the review, the challenges and future perspectives regarding cellulose-based adsorbents are discussed, thus providing an in-depth overview of the current state of the art in cellulose hybrid adsorbents for extraction of pharmaceuticals from water. This is expected to inspire the development of solid phase exraction materials that are efficient, relatively cheap, and prepared in a sustainable way.

Cigarettes butt littering: The story of the world's most littered item from the perspective of pollution, remedial actions, and policy measures

Cigarettes butt (CB) is one of the most littered items on the planet. This paper critically analyzes the factors responsible for CB littering, and associated environmental ramifications, and reviews all the possible technical, behavioural, and policy-based solutions. Even while smoking has declined globally, middle-income nations have seen an increase in consumption, which may be related to increased affordability and a lack of public awareness. The smokers' individual beliefs and habits, environmental ignorance, covert littering as a result of social taboos associated with smoking, and behavioural gaps between intention and action might all be contributing factors to CBs' littering behaviour. The low biodegradability of cellulose acetate filters and toxic chemical leaching from CBs are the most important aspects of CB environmental toxicity. The small size and low economic value of CB contribute to the inefficiencies of current waste collection and management systems. The current research on CB valorisation includes fired-clay bricks, asphalt concrete, biofilms, sound absorber, cellulose pulp, pesticides, and insecticides as downstream mitigation strategies. This study highlights the urgent need for policymakers to enforce regulations enabling innovative cigarette designs, the creation of deposit-refund schemes, extended producer responsibility and stringent waste collection mechanisms. Adopting gentler marketing strategies and non-confrontational behavioural nudges could result in an overall reduction in CB pollution.

A comprehensive review on triple R eco-management strategies to reduce, reuse and recycle of hazardous cigarette butts

Cigarettes are the globally consumed product that contributes to public health problems and is the source of the most prevalent form of litter in the world, Cigarette butts. Cigarette butts are a major source 4000 toxic chemicals, affecting the health of wildlife, humans, and the environment and their decomposition can take years due to the resistance of cellulose acetate to bacterial and fungal degradation. In 2016, the world production of cigarettes exceeded 5.7 trillion, with the majority of them consisting of cellulose acetate filters. Consequently, a massive amount of hazardous waste leaches out in the environment. Incineration and landfilling are methods of disposal, but they can result in the emission of harmful fumes and be costly. To combat this environmental issue, researchers have explored the recycling of cigarette butts in various materials, including asphalt concrete, fired clay bricks, and as a carbon source, among others. Various approaches can be used to reduce cigarette butts pollution, but efficient collection logistics by consumers remains a crucial factor for successful recycling. This paper provides innovative solutions to mitigate the cigarette butts litter problem and the feasibility of recycling methods. Despite recent progress in cigarette butts recycling solutions, there is still much room for research in this area.

Super-adsorbent microspheres based on a triallyl isocyanurate-maleic anhydride copolymer for the removal of organic pollutants from water

Owing to the frequent occurrence of diclofenac sodium (DS) in fresh aquatic environments and its potential toxicity towards living organisms, the effective removal of DS has attracted worldwide attention. Herein, a green and efficient strategy to fabricate crosslinked microspheres with interconnected mesoporous structures and abundant adsorption active sites was developed. With this strategy, triallyl isocyanurate (TAIC)-maleic anhydride (MAH) copolymer microspheres (TMs) with a diameter of 1.19-1.35 μm were first prepared by self-stabilized precipitation (2SP) polymerization, and the TMs possess a large amount reactive anhydride groups (62.5-71.8 mol%), a specific surface area of 51.6-182.4 m² g^-1 and a mesoporous structure (average pore size: 3.4-3.8 nm). Then the TMs were further functionalized with polyethylenimine (PEI) to give rise to cationic microspheres (Cat-TMs), which showed excellent adsorption performance to DS with a rapid adsorption rate (reached equilibrium within 30 min), a very high equilibrium adsorption capacity (1421 mg g^-1) and excellent recyclability. The pseudo-second-order model and Langmuir model were a good fit for the adsorption kinetic and isotherm process, respectively. Furthermore, due to the high cation density (4.291 mmol g^-1) and excellent pH buffer capacity of Cat-TMs, the adsorption capacity can be maintained at a high level within the pH range of 6-10. The regenerated Cat-TMs showed only a slight loss (<5%) in the adsorption capacity even after 5 adsorption-desorption cycles. In short, Cat-TMs can be considered as a highly promising adsorbent for the rapid and ultra-efficient removal of anionic organic contaminants and have significant potential to be applied in wastewater treatment.

Recent advances and future perspective on nanocellulose-based materials in diverse water treatment applications

Over the past few years, nanocellulose and its derivatives have drawn attention as promising bio-based materials for water treatment applications due to their high surface area, high strength, and renewable, biocompatible nature. The abundance of hydroxyl functional groups on the surfaces of cellulose nanocrystals (CNCs) and cellulose nanofibrils (CNFs) enables a broad range of surface modifications which results in propitious nanocomposites with tunable characteristics. In this context, this review describes the continuously developing applications of nanocellulose-based materials in the areas of adsorption, catalysis, filtration, and flocculation, with a special emphasis on the removal of contaminants such as heavy metals, dyes, and pharmaceutical compounds from diverse water systems. Recent progresses in the diverse forms of application of nanocellulose adsorbents (suspension, hydrogel, aerogel, and membrane) are also highlighted. Finally, challenges and future perspectives on emerging nanocellulose-based materials and their possible industrial applications are presented and discussed.

Cellulose and its derivatives, coffee grounds, and cross-linked, β-cyclodextrin in the race for the highest sorption capacity of cationic dyes in accordance with the principles of sustainable development

In this study, seven different materials were analyzed and includes coffee grounds (CG), two types of cellulose (CGC and CC), two types of modified cellulose (CT and CTCD), and cross-linked β-cyclodextrin (CD-1 and CD-2) were tested as adsorbents for the removal of dyes from the wastewater. The composition, morphology, and presence of functional groups in the obtained sorption materials were characterized by elemental analysis, SEM, TG/DTA, and FTIR spectroscopy. The sorption processes of the model contaminant, crystal violet (CV), were studied by kinetics and equilibrium models. The results showed, that using CTCD, the dye was adsorbed rapidly in 1 min and the slowest adsorption occurred in 20 min by CG. The time evolution was adjusted using a two-model, pseudo second-order model (CG and CGC) and pseudo first-order model in the rest adsorbents. According to the Langmuir and Sips isotherm models, the maximum adsorption capacities were very high in each case ranging from 1092.24 to 1220.40 mg g^-1. Moreover, the adsorption capacity of the near-natural materials remained even higher after five regeneration cycles. The regeneration is almost waste-free and the materials used can be decomposed during composting. In addition, almost complete removal of cationic dyes was observed during the treatment of real wastewater samples.

Removal of pharmaceuticals (diclofenac and amoxicillin) by maltodextrin/reduced graphene and maltodextrin/reduced graphene/copper oxide nanocomposites

Due to the scarcity of water and the growing industrialization, pharmaceutical wastewater treatment is of particular importance. For this reason, it is necessary to achieve an efficient method to eliminate all types of pharmaceutical pollutants. Herein, synthetic nano-composite is proposed to take a step towards improving the operation of removing pharmaceutical contaminants from the environment and aquatic and industrial effluents. Binary (maltodextrin/reconstituted graphene nanocomposite) and ternary (maltodextrin/reconstituted graphene nanocomposite/copper oxide) nanocomposites were prepared and characterized using, FT-IR, FESEM-EDS, TEM, DLS, and XRD. The nanocomposites were used to eliminate diclofenac and amoxicillin as Pharmaceuticals. The removal of amoxicillin at a concentration of 30 mg/L with an adsorbent dose of 0.05 g and a pH of 7.4 and an optimal temperature of 20 °C in 10 min has the highest removal rate of 86%. In addition, diclofenac with nano-adsorbents prepared under optimal conditions, including an initial concentration of 20 mg/L, adsorbent dose of 0.05 g, adsorption time of 7 min, a temperature of 20 °C and a pH of 7, has the highest removal efficiency of 94%. The results indicated that the prepared nanocomposites are alternative adsorbents to remove Pharmaceuticals from water.

Fabrication of Polyethyleneimine-Functionalized Magnetic Cellulose Nanocrystals for the Adsorption of Diclofenac Sodium from Aqueous Solutions

Diclofenac sodium (DS), one of the most used non-steroidal anti-inflammatory drugs worldwide, is often detected in wastewater and natural water. This drug is ecotoxic, even at low concentrations. Therefore, it is essential to fabricate low-cost adsorbents that can easily and effectively remove DS from contaminated water bodies. In this study, a polyethyleneimine (PEI)-modified magnetic cellulose nanocrystal (MCNC) was prepared with a silane coupling agent as a bridge. TEM, FTIR, XRD, and VSM were used to demonstrate the successful preparation of MCNC-PEI. This composite adsorbent exhibited efficient DS removal. Furthermore, the adsorption performance of MCNC-PEI on DS was optimal under mildly acidic conditions (pH = 4.5). Adsorption kinetics showed that the adsorption process involves mainly electrostatic interactions. Moreover, the maximum adsorption capacity reached 299.93 mg/g at 25 °C, and the adsorption capacity only decreased by 9.9% after being reused five times. Considering its low cost, low toxicity, and high DS removal capacity, MCNC-PEI could be a promising adsorbent for treating DS-contaminated water.

Magnetic porous biochar as a renewable and highly effective adsorbent for the removal of tetracycline hydrochloride in water

In this study, discarded cigarette butts were used as a precursor for preparing magnetic porous biochar with a facile annealing method. The magnetic porous biochar was applied to remove tetracycline hydrochloride (TCH) from aqueous solution. It exhibited excellent adsorption capacity for TCH, which was much higher than various similar materials reported. At the same time, the adsorption kinetics and adsorption isotherms of TCH were well fitted to the pseudo-second-order models and Freundlich models, respectively. The thermodynamics experiments proved that the adsorption on magnetic porous biochar was an endothermic reaction. Furthermore, the adsorption mechanism was explored, and the outstanding adsorption ability was mainly dependent on the pore filling effect, electrostatic interaction, and π-π interaction. By using the magnetic porous biochar, the real water samples were treated and high removal efficiency to TCH was obtained. What's more, the excellent reusability endowed the magnetic porous biochar with great potential as adsorbents for practical application.

Application of polysaccharide biopolymers as natural adsorbent in sample preparation

Preparing samples for analyses is perhaps the most important part to analyses. The varied functional groups present on the surface of biopolymers bestow them appropriate adsorption properties. Properties like biocompatibility, biodegradability, presence of different surface functional group, high porosity, considerable absorption capacity for water, the potential for modification, etc. turn biopolymers to promising candidates for varied applications. In addition, one of the most important parts of determination of an analyte in a matrix is sample preparation step and the efficiency of this step in solid phase extraction methods is largely dependent on the type of adsorbent used. Due to the unique properties of biopolymers they are considered an appropriate choice for using as sorbent in sample preparation methods that use from a solid adsorbent. Many review articles have been published on the application of diverse adsorbents in sample preparation methods, however despite the numerous advantages of biopolymers mentioned; review articles in this field are very few. Thus, in this paper we review the reports in different areas of sample preparation that use polysaccharides-based biopolymers as sorbents for extraction and determination of diverse organic and inorganic analytes.

Initial Conditioning of Used Cigarette Filters for Their Recycling as Acoustical Absorber Materials

Used cigarette butts represent a major and problematic form of waste, due to their abundance, toxicity, and durability. Moreover, the few proposals for their recycling are clearly insufficient, and new ones are welcome. For a new proposal regarding the reuse of used cigarette butts as acoustical absorbers in building construction, previous conditioning of the used butts is performed. This conditioning includes the elimination of moisture and toxic products accumulated in the filter of the cigarettes. Thus, in this work, the moisture content effect in acoustical absorption was analyzed, and a proposal for elimination is made. Moreover, a chemical cleaning procedure is proposed, and its influence on the acoustical behavior of the samples was also analyzed.

Direct imaging evidences of metal inorganic contaminants traced into cigarettes

Today, environmental health research on toxicological adverse effects of metal-inorganic materials diffused by cigarettes represents a new challenge for assessing new health risks directly related to the critical chemical-size features of the particles. Therefore, morpho-chemical analyses of hazardous particles become critical in response to the distinctive assumptions about the origin, evolution, and coexisting phases. Here, we report a detailed investigation through direct microscopy imaging of metal-inorganic contaminants for one traditional and two heat-not-burn commercial cigarettes of three different brands. Chemical-size studies revealed the critical presence of heavy metal-inorganic nanostructured microparticles on both paper and filter components of the cigarette, before and after smoking. The direct experimental imaging evidenced on how hazardous particles evolved in mass-size forming coexisting multi-phases of large agglomerate because of the persistence and accumulative effect of the heating puffing. The estimated porosity of the unsuitable engineered filters validated the allowed migration of micrometric pollutants independently from their intrinsic size-shape property. Furthermore, the inappropriate design of the filters made it an adverse sponge reservoir capable of collecting all possible hazardous chemical agents potentially toxic. These substantial results strongly support experimentally the tremendous effect of the smoke capable of transporting and manipulating a high amount of elusive particles, as a particles heat carrier.

Insights into Equilibrium and Adsorption Rate of Phenol on Activated Carbon Pellets Derived from Cigarette Butts

In the present work, the preparation of activated carbon pellets from cigarette butts by thermal treatment was evaluated. The morphological, textural, topological, and surface chemical properties were studied by SEM-EDX, N2 adsorption, Raman, and FTIR spectroscopy. For adsorption assays, activated carbon was tested for the adsorption of phenol as a model molecule at different solution pH, temperature, and type of water. In addition, leaching tests before and after carbonization were conducted to evaluate the lixiviation of ions present in the solid. The results revealed a microporous material, composed of cylindrical fibers (thickness of 13 µm) with a microporous area of 713 m2/g and narrow and uniform slit-shaped pores (0.4–0.8 nm). The surface chemistry analysis evidenced the presence of oxygenated groups (carboxylic, esters, and phenolics). Activated carbon leaching tests indicated that the concentrations of the leached ions did not exceed the maximum permissible limit for drinking water. Phenol adsorption revealed an exothermic process with a maximum adsorption capacity of 272 mg/g at 10 °C. Finally, it was confirmed that phenol diffusion was drastically affected by hindered phenomena due to the similarity in the molecular size of phenol and the average size of micropores, and as a result an effective diffusion coefficient between 6.10 × 10−0 and 5.50 × 10−12 cm2/s and a maximum tortuosity value of 3.3 were obtained.

Toxicity of cigarette butts and possible recycling solutions-a literature review

Tobacco is a worldwide-consumed product, which in addition to causing public health-related issues is responsible for the most common form of litter in the world-smoked cigarette butts (CBs). A large attention has been drawn to this question, since this specific waste type tends to end up in terrestrial and aquatic ecosystems, posing serious threat to a range of life forms. Decomposition may take several years to occur because cellulose acetate is hardly accessible, before deacetylation, by bacteria and fungi. This review concerns the toxicity derived from smoked cigarette butts, as well as innovative ecological solutions for solving the CB litter problem. Toxicity studies have demonstrated the critical influence of chemicals present in smoked CBs to the environment as a whole, but also the physical contaminating potential considering micro- and nanoparticles derived from CB material. Nevertheless, several technological approaches were aimed at unveiling hidden value within used CBs, as well as propositions for incorporation of this residue in large volume production items or direct recycling. In summary, several methods are available to alleviate CB pollution, while appropriate and efficient collection logistics by consumers appears as the main bottleneck for an effective recycling. It is also clear that while considerable progress has been made recently in light of CB recycling solutions, there is still a vast research capacity in this regard.

Use of Nanocellulose extracted from grass for adsorption abatement of Ciprofloxacin and Diclofenac removal with phyto, and fish toxicity studies

The present study deals with the adsorption of antibiotic Ciprofloxacin (CPXO) and anti-inflammatory agent Diclofenac (DCF) on Grass nanocellulose (GNC) extracted from Cyprus rotundas grass. The adsorbent GNC was characterised using various microscopic, elemental and spectroscopic analysis to monitor the physicochemical alterations of the surface before and after adsorption. The size of the converted nanocellulose was found to be 40-50 nm. The experimental measures influencing the adsorption of CPXO and DCF that were optimised are initial solution pH, GNC dosage, temperature and initial concentration of the adsorbate. Halsey isotherm model and pseudo-second order kinetic model agreed best with the experimental outcome for both the adsorbate. The maximum adsorption capacity of GNC were 227.223 and 192.307 mg/g for CPXO and DCF respectively. Phytotoxicity studies were performed using 6 different types of seeds to evaluate the effect of GNC treated effluent on plants. Similarly, acute fish toxicity on zebra fish analysis showed to have lesser mortality rate of the effluent after adsorption of CPXO and DCF on GNC.

A Clean Process for Obtaining High-Quality Cellulose Acetate from Cigarette Butts

The main purpose of this study is to introduce a modified method for recovering and recycling huge number of cigarette butts (CBs) and convert them into a fashion product. CBs are non-biodegradable waste, generally, discarded improperly into the environment. CBs consist of cellulose acetate, which can be recovered through extraction and purification processes. CBs are the most numerically frequent form of waste in the world. A relevant portion of CBS are discarded improperly into the environment. The principal filter components are plasticized cellulose acetate fibers that have the slowest degradation rate (up to years). In fact, a limiting step is the hydrolysis of cellulose acetate polymer into cellulose and acetic acid, which is extremely slow under ambient conditions and represents a relevant environmental risk. A number of studies have been realized on recycling cigarette butts with encouraging results, and several methods have been studied, including recycling of cigarette butts in asphalt concrete and fired clay bricks, as a carbon source, sound-absorbing material, corrosion inhibitor, biofilm carrier, and many more. In this study, we propose a novel, green, low cost, simple, and efficient extraction method of cellulose acetate fibers (CA) from discarded cigarette butts (DCBs). CBs extraction procedure involves a two-step process consisting of washings in water and some subsequent washings in ethanol. The obtained samples of CA are dried at 60 °C for 60 min in the oven. The quality and properties of cellulose acetate extracted and purified are comparable to the pure cellulose acetate fiber used for cigarette butts. The preliminary results obtained on the recovered CA look promising to the use of this recovery material from cigarette butts to obtain a wide consumption fashion product, such as eyeglass frames.

Amine functionalized egg albumin hydrogel with enhanced adsorption potential for diclofenac sodium in water

The removal of diclofenac sodium (DFS) from wastewater has attracted increasing attention because it is within the extensively prescribed nonsteroidal anti-inflammatory drugs and pose ecotoxicity. Therefore, fabrication of versatile adsorbents of low-cost, higher-effectiveness and excellent recyclability is significant for the treatment of DFS contaminated wastewater. This work reports a promising biobased egg albumin (ALB) hydrogel functionalized with a large density of adsorptive amine sites via polyethyleneimine (PEI). The composite ALB/PEI hydrogel demonstrated an excellent DFS removal capacity, i.e. 232.5 mg/g, in an optimum experimental condition (pH∼6; contact time∼180 min; adsorbent dosage∼0.5 g/L) which revealed to be considerably higher or competitive than many reported adsorbents. The adsorption isotherms better accorded with the Langmuir model and the kinetics with the pseudo second-order model, indicating the mono-layer chemisorption process. Besides, the regeneration steps up to four sequential adsorption/desorption cycles demonstrated an excellent reusability. The Fourier-transform infrared spectrometry (FTIR), and X-ray photoelectron spectroscopy (XPS) results implied that the adsorption process followed via the electrostatic interactions, hydrogen bonding, and π-π stacking between the functionality of hydrogel and aromatic rings of DFS. Considering the low-cost, and an excellent DFS removal capacity, the natural composite ALB/PEI hydrogel could be a promising adsorbent for the treatment of DFS contaminated wastewater.

The toxicity and valorization options of cigarette butts

Cigarette butts, one of the most abundant forms of waste in the world, contain more than 4000 toxic chemicals and pose serious risks to the health of wildlife, humans, and marine and freshwater organisms. Although trivial in size, trillions of cigarettes are produced every year worldwide, resulting in the accumulation of tonnes of toxic waste litter. In 2016, a world production of over 5.7 trillion cigarettes was reported with the majority comprising cellulose acetate filters - a polymer with poor biodegradability. Depending on the environmental conditions, cellulose acetate filters can take up to 10 years to decompose during which time they leach heavy metals and toxic chemicals into the environment. Although possible disposal methods for collected cigarette butt waste include incineration and landfilling, both techniques may result in the release of hazardous fumes and can be costly. However, recycling CBs in different materials could be a possible solution for this concurrent environmental pollution. A number of novel studies have been publicized on recycling cigarette butts with encouraging results, and several methods have been studied, including recycling of cigarette butts in asphalt concrete and fired clay bricks, as a carbon source, sound absorbing material, corrosion inhibitor, biofilm carrier, and many more. Hence, this paper provides a comprehensive review and discussion of various studies that have been carried out on the toxicity and valorization of cigarette butt waste and investigates the feasibility and sustainability of recycling methods adopted. Further research and developments are essential for the widespread application of recycling cigarette butts.

Modified biochar from Moringa seed powder for the removal of diclofenac from aqueous solution

In this study, Moringa seed powder (M_SP) was pyrolyzed at 450 °C to synthesize Moringa seed powder biochar (M_SPB) and treated with phosphoric acid (H₃PO₄) to synthesize phosphate-modified Moringa seed powder biochar (M_SPB-HPO) as an adsorbent for the removal of diclofenac (Dfc) from aqueous solution. Fourier transform infrared (FTIR) analysis, energy dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM), and pH point of zero charge (pH_pzc) were conducted to give more insight into the adsorbent's properties. The SEM analysis showed the transformations in the surface morphology from the parent material to the synthesized materials after the thermal and acid treatment. EDS analysis revealed the variation in the elemental composition of the materials prior to and after adsorption of Dfc ions. The FTIR analysis showed changes and peak intensities of functional groups involved in Dfc removal. The pH_pzc showed the charge carried by M_SPB-HPO in different pH conditions. Isotherm data best matched the Sips model, and the pseudo-second-order model best described the adsorption kinetics. The maximum adsorption capacity of M_SPB-HPO by Sips model was found to be 100.876 mg g^-1.