A critical review on visible-light-response CeO2-based photocatalysts with enhanced photooxidation of organic pollutants

Recent Advances of CeO2-Based Composite Materials for Photocatalytic Applications

Photocatalysis has the advantages of practical, sustainable and environmental protection, so it plays a significant role in energy transformation and environmental utilization. CeO2 has attracted widespread attention for its unique 4 f electrons, rich defect structures, high oxygen storage capacity and great chemical stability. In this paper, we review the structure of CeO2 and the common methods for the preparation of CeO2-based composites in the first part. In particular, we highlight the co-precipitation method, template method, and sol-gel method methods. Then, in the second part, we introduce the application of CeO2-based composites in photocatalysis, including photocatalytic CO2 reduction, hydrogen production, degradation, selective organic reaction, and photocatalytic nitrogen fixation. In addition, we discuss several modification techniques to improve the photocatalytic performance of CeO2-based composites, such as elemental doping, defect engineering, constructing heterojunction and morphology regulation. Finally, the challenges faced by CeO2-based composites are analyzed and their development prospects are prospected. This review provides a systematic summary of the recent advance of CeO2-based composites in the field of photocatalysis, which can provide useful references for the rational design of efficient CeO2-based composite photocatalysts for sustainable development.

Enhancing degradation of sulfamethoxazole by layered double hydroxide/carbon nanotubes catalyst via synergistic effect of photocatalysis/persulfate activation

A Co3Mn-LDHs and carbon nanotube (Co3Mn-LDHs/CNT) composite catalyst was constructed for permonosulfate (PMS) activation and degrading sulfamethoxazole (SMX) under Vis light irradiation. The introduction of CNTs into Co3Mn-LDHs facilitate the exciton dissociation and carrier migration, and the e- and h+ were readily separated from Co3Mn-LDHs/CNT in the photocatalysis process, which promoted the production rate of reactive oxygen species (ROS), so the Co3Mn-LDHs + Vis + PMS system exhibited better activity with an SMX degradation ratio of 61.25% than those of Co3Mn-LDHs + Vis system (42.30%) and Co3Mn-LDHs + PMS system (48.30%). After 10 cycles, the degradation rate of SMX only decreased by 7.16%, indicating the good reusability of the Co3Mn-LDHs/CNTs catalyst. The results of electron paramagnetic resonance (EPR) analysis and radical quenching experiments demonstrated that that the SO4•- played crucial role for SMX removal in Co3Mn-LDHs/CNTs + Vis + PMS system, and both e- and h+ made an important contribution to activating PMS to produce ROS. Overall, this work provided an excellent catalyst for photo-assisted PMS activation and suggested the activation mechanism for organic pollutant remediation.

New types of open-framework vanadium borophosphates with photocatalytic properties

The exploration of new open-framework polyoxometalates is very significant in structural chemistry and materials science. Herein, three new organic hybrid three-dimensional vanadium borophosphates (H3O)7(H2aeae)3{[Cd(H2O)3]2[H3O⊃(V2BP2O12)6]}·15H2O (1, aeae = 2-(2-aminoethylamino)ethanol) and (H3O)5(H2aeae)3{[TM(H2O)2.5(H2aeae)0.5]2[H3O⊃ (V2BP2O12)6]}·9H2O [TM = Mn(2), Co(3)] were hydrothermally prepared and structurally characterized. The three vanadium borophosphates contain similar 12-member ring crown-shaped clusters [(V2BP2O12)6]18- based on the linkage of six [V2O8] dimers and six [BP2O10] units. The [(V2BP2O12)6]18- cluster is further bridged by the unsaturated [Cd(H2O)3]2+ or [TM(H2O)2.5(H2aeae)0.5]3+ complexes to build new types of open-framework vanadium borophosphates with pores and cavities retained by the protonated H2aeae2+, H3O+ and free H2O. Surprisingly, the monodentate H2aeae2+ ligand coordinating with a metal center was observed in 2 and 3 for the first time as the aeae molecule acted as the trichelating ligand. Their optical absorption edges were determined to be in the range of 2.61-2.68 eV using solid-state UV-vis spectroscopy. 1-3 exhibited excellent photocatalytic activity towards methylene blue (MB) degradation under visible light irradiation, which presented the first example of organic hybrid open-framework vanadium borophosphates as the photo-catalysts for MB degradation.

Fermi level pinning in metal oxides: influence on photocatalysis and photoelectrochemistry

Photocatalysis and photoelectrochemical (PEC) reactions are complex processes involving both the physical properties and surface chemistry of the semiconductor photocatalyst. Their interplay applies specific limitations on the performance of different materials in light-driven reactions, often despite their optimal band structure and optical absorption. One of the ways to properly characterize the photocatalytic and PEC properties of semiconductors remains the measurement of the photopotential, which characterizes a driving force of photoinduced processes in the material. In this work, we give a general scope on the photopotential in PEC reactions that finds its origin in semiconductor physics. It is shown that the photopotential does not always play an interchangeable role with the photocurrent in comparative analysis of the photocatalytic performance of different materials. Furthermore, a correlation between the photopotential and the kinetics of methylene blue dye photocatalysis is shown for anatase-TiO2, CeO2and WO3as photocatalysts. Fermi level pinning (FLP) in the bandgap of CeO2is observed limiting the photoactivity of the compound, which is attributed to the high defectivity of CeO2. A short review is given on the possible origins of FLP in metal oxides and ways to overcome it. It is pointed out that the shift of the Fermi level after illumination of CeO2can trigger the chemical instability of the material accompanied by the FLP process.

CeO2 nanospheres incorporated with Bi2MoO6/g-C3N4 enhanced photocatalysis towards environmental pollutant Rhodamine B removal

We have adopted a novel CeO2/Bi2MoO6/g-C3N4-based ternary nanocomposite that was synthesized via hydrothermal technique. The physiochemical characterization of as-prepared samples was examined through various analytical techniques such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy TEM, photoluminescent spectra (PL), X-ray photoelectron spectroscopy (XPS), Brunauer-Emmett-Teller (BET), and ultraviolet diffuse reflectance spectroscopy (UV-DRS) technique. In addition, the photocatalytic performance was carried out by degradation of Rhodamine B dye under visible light irradiation using this nanocatalyst. The ternary nanocomposite achieved 94% of the degradation efficiency within 100 min which is higher than the pristine and binary composites under the predetermined condition pH = 7, Rhodamine B dye = 5 mg/L, and catalyst concentration = 150 mg/L. The experimental synergetic effect of CeO2/Bi2MoO6/g-C3N4 ternary nanocomposite has been ascribed to the interfacial charge carrier migration between CeO2, Bi2MoO6, and g-C3N4. The optical absorption range of CeO2/Bi2MoO6/g-C3N4 ternary nanocomposite was enhanced, and the band gap was reduced up to 2.2 eV. In addition, scavenger trapping experiment proves that the super oxide anions (O2-.) and photogenerated holes are the major active species. The reusability and stability experiment proved the CeO2/Bi2MoO6/g-C3N4 ternary nanocomposite keeps good durability during the photocatalytic degradation process after the five successive cycles. Furthermore, based on the results, the charge carrier transfer photocatalytic mechanism was also discussed. This CeO2/Bi2MoO6/g-C3N4 ternary nanocomposite may offer the cheapest material and extend the great opportunity for clean and environmental remediation approach under the visible light irradiation.

Banana peel extract for CeO2 nanoflower synthesis: Enhancing photocatalytic activity for methyl orange dye removal and bactericidal effects

The cube architecture associated with the CeO2 nanoflowers (NFs) that generated, which had an average crystallization width of 7 nm, has been confirmed by X-ray crystallographic investigations. The method used is environmentally acceptable since it converts wasted banana peel extracts into CeO2 nanoflower. On the basis of artwork obtained from a High-Resolution Transmission Electron Microscope (HR-TEM), CeO2 nanoparticles have been observed to possess a spherical shape and an average particle diameter of 21 nm. To take the purpose of this study, green-fabricated CeO2-NFs were used to investigate the photocatalytic oxidation of methyl orange (MO) dye when exposed to sunshine. CeO2 nanofibers showed a degradation performance of 98% when compared to methyl orange dye. Evidently is a possibility that this may be caused by the presence of CeO2 nanoflowers, whereby enhance the interaction of electrons, which are holes dissolution, and adherence. Upon a single day of being exposed, the biocidal potential was tested against both gram-positive and gram-negative bacteria, including E. coli, B. cereus, and S. aureus, among others. Due to the fact that its 32 mm minimum inhibitory concentration (MIC) for B. cereus was the highest among conventional medicines. As shown by the extraordinary capabilities of WBP@CeO2 tiny particles, manipulating of flexible tiny particles to feed the purpose of achieving effective and customizable infections and dermatologist advancements is really stunning.

CO2 Photoreduction over Semiconducting 2D Materials with Supported Single Atoms: Recent Progress and Challenges

In the face of the growing energy crisis and environmental challenges, substantial efforts are now directed toward sustainable clean energy as a replacement for traditional fossil fuels. CO2 photoreduction into value-added chemicals and fuels is widely recognized as a promising approach to mitigate current energy and environmental concerns. Photocatalysts comprising single atoms (SAs) supported on two-dimensional (2D) semiconducting materials (SAs-2DSemi) have emerged as a novel frontier due to the combined merits of SA catalysts and 2D materials. In this study, we review advancements in metal SAs confined on 2DSemi substrates, categorized into four groups: (1) metal oxide-based, (2) g-C3N4-based, (3) emerging, and (4) hybridized 2DSemi, for photocatalytic CO2 conversion over the past few years. With a particular focus on highlighting the distinct advantages of SAs-2DSemi, we delve into the synthesis of state-of-the-art catalysts, their catalytic performances, and mechanistic elucidation facilitated by experimental characterizations and theoretical calculations. Following this, we outline the challenges in this field and offer perspectives on harnessing the potential of SAs-2DSemi as promising photocatalysts. This comprehensive review aims to provide valuable insights for the future development of 2D photocatalytic materials involving SAs for CO2 reduction.

Highly visible-light-active sulfur and carbon co-doped TiO2 (SC-TiO2) heterogeneous photocatalysts prepared by underwater discharge plasma

To promptly and simply create highly crystalline S/C co-doped TiO2 (SC-TiO2) photocatalysts at room temperature and atmospheric pressure, we suggest a novel plasma-assisted sol-gel synthesis method. This method is a simultaneous synthetic process, in which an underwater plasma undergoes continuous reactions to generate high-energy atomic and molecular species that enable TiO2 to achieve crystallinity, a large surface area, and a heterogeneous structure within a few minutes. In particular, it was demonstrated that the heterogeneously structured TiO2 was formed by doping that sulfur and carbon replace O or Ti atoms in the TiO2 lattice depending on the composition of the synthesis solution during underwater plasma treatment. The resultant SC-TiO2 photocatalysts had narrowed bandgap energies and extended optical absorption scope into the visible range by inducing the intermediate states within bandgap due to generation of oxygen vacancies on the surface of TiO2 through synthesis, crystallization, and doping. Correspondingly, SC-TiO2 showed a significant degradation efficiency ([k] = 6.91 h-1) of tetracycline (TC, antibiotics) under solar light irradiation, up to approximately 4 times higher compared to commercial TiO2 ([k] = 1.68 h-1), resulting in great water purification. Therefore, we anticipate that this underwater discharge plasma system will prove to be an advantageous technique for producing heterostructural TiO2 photocatalysts with superior photocatalytic efficiency for environmental applications.

Pathogen-Activated Macrophage Membrane Encapsulated CeO2-TCPP Nanozyme with Targeted and Photo-Enhanced Antibacterial Therapy

Nanozymes with peroxidase-mimic activity have recently emerged as effective strategies for eliminating infections. However, challenges in enhancing catalytic activities and the ability to target bacteria have hindered the broader application of nanozymes in bacterial infections. Herein, a novel nanozyme based on mesoporous CeO2 nanosphere and meso-tetra(4-carboxyphenyl)porphine (TCPP) encapsulated within pathogen-activated macrophage membranes, demonstrates photodynamic capability coupled with photo-enhanced chemodynamic therapy for selective and efficient antibacterial application against infected wounds. Interestingly, the expression of Toll-like receptors accordingly upregulates when macrophages are co-cultured with specific bacteria, thereby facilitating to recognition of the pathogen-associated molecular patterns originating from bacteria. The CeO2 not only serve as carriers for TCPP, but also exhibit intrinsic peroxidase-like catalytic activity. Consequently, Staphylococcus aureus (S. aureus)-activated macrophage membrane-coated CeO2-TCPP (S-MM@CeO2-TCPP) generated singlet oxygen, and simultaneously promoted photo-enhanced chemodynamic therapy, significantly boosting reactive oxygen species (ROS) to effectively eliminate bacteria. S-MM@CeO2-TCPP specifically targeted S. aureus via Toll-like receptor, thereby directly disrupting bacterial structural integrity to eradicate S. aureus in vitro and relieve bacteria-induced inflammation to accelerate infected wound healing in vivo. By selectively targeting specific bacteria and effectively killing pathogens, such strategy provides a more efficient and reliable alternative for precise elimination of pathogens and inflammation alleviation in microorganism-infected wounds.

Antibacterial and sunlight-driven photocatalytic activity of graphene oxide conjugated CeO2 nanoparticles

This work focuses on the structural, morphological, optical, photocatalytic, antibacterial properties of pure CeO2 nanoparticles (NPs) and graphene oxide (GO) based CeO2 nanocomposites (GO-1/CeO2, GO-5/CeO2, GO-10/CeO2, GO-15/CeO2), synthesized using the sol-gel auto-combustion and subsequent sonication method, respectively. The single-phase cubic structure of CeO2 NPs was confirmed by Rietveld refined XRD, HRTEM, FTIR and Raman spectroscopy. The average crystallite size was calculated using Debye Scherrer formula and found to increase from 20 to 25 nm for CeO2 to GO-15/CeO2 samples, respectively. The related functional groups were observed from Fourier transform infrared (FTIR) spectroscopy, consistent with the outcomes of Raman spectroscopy. The optical band gap of each sample was calculated by using a Tauc plot, which was observed to decrease from 2.8 to 1.68 eV. The valence state of Ce (Ce3+ and Ce4+) was verified using X-ray photoelectron spectroscopy (XPS) for CeO2 and GO-10/CeO2. The poisonous methylene blue (MB) dye was used to evaluate the photocatalytic activity of each sample in direct sunlight. The GO-15/CeO2 nanocomposite showed the highest photocatalytic activity with rate constant (0.01633 min-1), and it degraded the MB dye molecules by 100% within 120 min. The high photocatalytic activity of this material for degrading MB dye establishes it as an outstanding candidate for wastewater treatment. Further, these nanocomposites also demonstrated excellent antimicrobial activity against Pseudomonas aeruginosa PAO1.

Safety assessment and gastrointestinal retention of orally administered cerium oxide nanoparticles in rats

Cerium oxide nanoparticles (CeO2 NPs, NM-212) are well-known for their catalytic properties and antioxidant potential, and have many applications in various industries, drug delivery, and cosmetic formulations. CeO2 NPs exhibit strong antimicrobial activity and can be used to efficiently remove pathogens from different environments. However, knowledge of the toxicological evaluation of CeO2 NPs is too limited to support their safe use. In this study, CeO2 NPs were orally administered to Sprague Dawley rats for 13 weeks at the doses of 0, 10, 100, and 1000 mg/kg bw/day, followed by a four week recovery period. The hematology values for the absolute and relative reticulocyte counts in male rats treated with 1000 mg/kg bw/day CeO2 NPs were lower than those in control rats. The clinical chemistry values for sodium and chloride in the treated male rat groups (100 and 1000 mg/kg/day) and total protein and calcium in the treated female rat groups (100 mg/kg/day) were higher than those in the control groups. However, these changes were not consistent in both sexes, and no abnormalities were found in the corresponding pathological findings. The results showed no adverse effects on any of the parameters assessed. CeO2 NPs accumulated in the jejunum, colon, and stomach wall of rats administered 1000 mg/kg CeO2 NPs for 90 days. However, these changes were not abnormal in the corresponding histopathological and immunohistochemical examinations. Therefore, 1000 mg/kg bw/day may be considered the "no observed adverse effect level" of CeO2 NPs (NM-212) in male and female SD rats under the present experimental conditions.

Rare earth oxide based electrocatalysts: synthesis, properties and applications

As an important strategic resource, rare earths (REs) constitute 17 elements in the periodic table, namely 15 lanthanides (Ln) (La-Lu, atomic numbers from 57 to 71), scandium (Sc, atomic number 21) and yttrium (Y, atomic number 39). In the field of catalysis, the localization and incomplete filling of 4f electrons endow REs with unique physical and chemical properties, including rich electronic energy level structures, variable coordination numbers, etc., making them have great potential in electrocatalysis. Among various RE catalytic materials, rare earth oxide (REO)-based electrocatalysts exhibit excellent performances in electrocatalytic reactions due to their simple preparation process and strong structural variability. At the same time, the electronic orbital structure of REs exhibits excellent electron transfer ability, which can reduce the band gap and energy barrier values of rate-determining steps, further accelerating the electron transfer in the electrocatalytic reaction process; however, there is a lack of systematic review of recent advances in REO-based electrocatalysis. This review systematically summarizes the synthesis, properties and applications of REO-based nanocatalysts and discusses their applications in electrocatalysis in detail. It includes the hydrogen evolution reaction (HER), oxygen evolution reaction (OER), hydrogen oxidation reaction (HOR), oxygen reduction reaction (ORR), carbon dioxide reduction reaction (CO2RR), methanol oxidation reaction (MOR), nitrogen reduction reaction (NRR) and other electrocatalytic reactions and further discusses the catalytic mechanism of REs in the above reactions. This review provides a timely and comprehensive summary of the current progress in the application of RE-based nanomaterials in electrocatalytic reactions and provides reasonable prospects for future electrocatalytic applications of REO-based materials.

Magnetic-acoustic actuated spinous microrobot for enhanced degradation of organic pollutants

A growing interest in the development of efficient strategies for the removal of organic pollutants from polluted water is emerging. As such, artificial micro/nano machines performing excellent water purification tasks have recently attracted more research attention of scientists. Hereby a spinous Fe3O4@PPy microrobot is presented that towards an efficient organic pollutant removal by enhancing Fenton-like reaction. The microrobot is fabricated by wrapping polypyrrole (PPy) on a spiny magnetic template prepared from sunflowers pollen. Modulating the sound pressure and frequency of the ultrasonic field enables the Fe3O4@PPy microrobot to present multimode motion, such as violent eruption-like motion caused by local cavitation (ELM), march-like unific motion (MLM), and typhoon-like rotation toward the center gathered motion (TLM). This multimode motion achieves the sufficient locomotion of microrobots in three-dimensional space and effective contact with organic pollutants in polluted water. Furthermore, a 5.2-fold increase in the degradation rate of methylene blue has been realized using Fe3O4@PPy microrobots under low-concentration hydrogen peroxide conditions. Also, the magnetically controlled recovery of microrobots from water after the completion of the degradation task has been demonstrated. The magnetic-acoustic actuated spinous microrobot can be extrapolated to other catalytic microrobot, developing a new strategy for an easier implementation and recovery of microrobot in real applications of water purification.

Enhanced degradation of micropollutants by visible light photocatalysts with strong oxygen activation ability

Visible light photocatalysis is widely considered a sustainable approach to break down micropollutants without chemical addition. To promote the output of photogenerated carriers under visible light, a Z-scheme plasmonic photocatalyst Bi-CeO2/Ag0/BiO2 was designed and fabricated to activate dissolved oxygen in water for micropollutant degradation. The doped Bi not only improved the separation of electron-hole, but also narrowed the band gap of CeO2 to enhance its absorption of visible light. Notably, metallic silver (Ag0) works as an electronic transmission vehicle from Bi-CeO2 to BiO2 in a Z-scheme mechanism. Likewise, the surface plasmon resonance effect of Ag0 also enhanced the absorption of visible light. Furthermore, the Bi doping induced abundant surface oxygen vacancies on CeO2 for enhanced capability and selectivity towards O2 adsorption and activation, which favored the generation of O2•- by photogenerated electrons to degrade sulfamethoxazole, enrofloxacin, and bisphenol A. Theoretical calculation results also confirmed the O2•--driven degradation pathway for sulfamethoxazole. Therefore, the Z-scheme Bi-CeO2/Ag0/BiO2 not only extends the photocatalytic reactivity of CeO2-based catalysts to the visible light range, but also provides a chemical-free method to effectively degrade micropollutants.

Cascaded Antitumor Therapy Excited by Dual Nanozymes Based on Energy Restriction and Photocatalysis

In nanocatalytic medicine, drugs can be transformed into toxic components through highly selective and highly specific catalytic reactions in the tumor microenvironment, avoiding toxic side effects on normal tissues. Due to the coexistence of Ce3+ and Ce4+, CeO2 is endowed with dual nanozyme activities. Herein, CeO2 nanoparticles served as templates to construct a biomimetic nanodrug delivery system (C/CeO2@M) by electrostatic adsorption of carbon quantum dots (CQDs) and coating a homologous tumor cytomembrane. After homologous targeting to tumors, the CQDs emitted 350-600 nm light under 660 nm laser irradiation by upconversion luminescence, which caused a CeO2-mediated photocatalytic reaction to generate reactive oxygen species. The catalase-like activity of CeO2-enabled converting excess H2O2 to O2, which not only alleviated tumor hypoxia and promoted intratumor drug delivery but also provided substrates for subsequent catalytic reactions. Meanwhile, the phosphatase activity of CeO2 could consume adenosine triphosphate (ATP) to block the energy supply for tumor cells, thus limiting cell proliferation and metastasis. The strategy of energy restriction and photocatalysis of dual nanozyme stimulation offers great potentials in enhancing drug penetration and eradicating solid tumors.

Efficient Exciton Dissociation on Ceria Chelated Cerium-Based MOF Isogenous S-Scheme Photocatalyst for Acetaldehyde Purification

Long-term exposure to low concentration indoor VOCs of acetaldehyde (CH3 CHO) is harmful to human health. Thus, a novel isogenous heterojunction CeO2 /Ce-MOF photocatalyst is synthesized via a one-step hydrothermal method for the effective elimination of CH3 CHO in this work. This CeO2 /Ce-MOF photocatalyst performs well in CH3 CHO removal and achieves an apparent quantum efficiency of 7.15% at 420 nm, which presents ≈6.7 and 3.4 times superior to those generated by CeO2 and Ce-MOF, respectively. The enhanced efficiency is due to two main aspects including i) an effective photocarrier separation ability and the prolonged reaction lifetime of excitons play crucial roles and ii) the formation of an internal electric field (IEF) is sufficient to overcome the considerable exciton binding energy, and increases the exciton dissociation efficiency by up to 50.4%. Moreover, the reasonable pathways and mechanisms of CH3 CHO degradation are determined by in situ DRIFTS analysis and simulated DFT calculations. Those results demonstrated that S-scheme heterojunction successfully increases the efficiency of harmful volatile organic compounds elimination, and it offers essential guidance for designing rare earth-based MOF photocatalysts.

Graphene-based photocatalysts for degradation of organic pollution

Compared with the traditional wastewater treatment technology, semiconductor photocatalysis is a rapidly emerging environment-friendly and efficient Advanced Oxidation Process for degradation of refractory organic contaminants. Single-component semiconductor photocatalysts exhibit poor photocatalytic performance and cannot meet the requirements of wastewater treatment. The combination of semiconductor photocatalysts and Graphene can effectively improve the photocatalytic activity and stability of semiconductor photocatalysts. This review focuses on the synergistic effect of several types of semiconductors with Graphene for photocatalytic degradation of organic pollutants. After a brief introduction of the photodegradation mechanism of semiconductor materials and the basic description of Graphene, the synthesis, characterization and degradation performance of various Graphene-based semiconductor photocatalysts are emphatically introduced.

Cellulose acetate/polyurethane blend as support matrix with high optical transparency and improved mechanical properties for photocatalyst CeO2 nanoparticles immobilization

Advanced manufacturing technologies for efficient catalytic materials have triggered the rational design of catalysts as well as extensive investigation into preparative methodologies. Herein, we report the preparation of new versatile cellulose acetate/polyurethane (CA/PU) blends for efficient immobilization of CeO2 nanoparticles, the appropriate composition of polymer mixture being chosen after rigorous analysis (SEM, FTIR, optical, mechanical). The band gap energy for hybrid films ranged between 3.02 eV and 2.05 eV, the lowest value being measured for the film with Co-doped CeO2 NPs (B3 film). The best results in photodegradation of methylene blue under visible-light irradiation was attained after 50 min for B3 film (rate constant k = 45.34× 10-3 min-1), while the total mineralization of MB in the same conditions as evaluated by HPLC-ESI MS and TOC analyses was achieved after 90 min. Effect of co-ions (SO42-, Cl- or NO3-) on photocatalytic performance was studied, and scavenger tests were used to identify the active species involved in the photocatalytic mechanism. Also, the photocatalytic efficiency of B3 sample was tested for rhodamine B, metronidazole and 4-nitrophenol degradation. Evaluation of the stability and integrity of hybrid film after 5 catalysis cycles reveal that the photocatalytic potential is retained with no substantial structural changes.

Ce4+/Ce3+ Redox Effect-Promoted CdS/CeO2 Heterojunction Photocatalyst for the Atom Economic Synthesis of Imines under Visible Light

The employment of stoichiometric alcohols and amines for imine synthesis under mild and green reaction conditions is still a challenge in the field. In this work, based on our research foundation in the thermocatalytic synthesis of imines over ceria, a CdS/CeO2 heterojunction photocatalyst was constructed and successfully realized the atom-economic synthesis of imines under visible light without additives at room temperature. Mechanistic experiments and corresponding characterizations indicated that the CdS/CeO2 heterojunction can improve the separation efficiency of photogenerated carriers, which can be further enhanced by the Ce4+/Ce3+ redox pair by rapidly combining photogenerated e-. The in situ-reduced Ce3+ can better activate O2 to form Ce-O-O·, which, together with h+, efficiently accelerates alcohol oxidation, which is the rate-determined step for the synthesis of imines via oxidative coupling reaction of alcohol and amine. In addition, our photocatalyst exhibited fairly decent reusability and substrate universality. This work solves problems of using base additives and excess amine or alcohol in the reported photocatalytic systems and provides new insight for designing CeO2-based photocatalytic oxidation catalysts.

Optimizing leachate treatment with titanium oxide-impregnated activated carbon (TiO2@ASC) in a fixed-bed column: characterization, modeling, and prediction study

This research focused on the application of a fixed bed column filled with immobilized titanium oxide-loaded almond shell carbon (TiO2@ASC) for the treatment of leachate. The adsorption performance of synthesized TiO2@ASC in fixed bed column is analyzed using adsorption experiments and modeling study. The characteristics of synthesized materials are determined by several instrumental techniques like BET, XRD, FTIR, and FESEM-EDX. The flow rate, initial concentration of COD and NH3-N, and bed height were optimized to determine the effectiveness of leachate treatment. The linear bed depth service time (BDST) plots equations with a correlation coefficient of greater than 0.98 confirmed the model's accuracy for COD and NH3-N adsorption in column structure. The adsorption process was found to be well predicted by an artificial neural network (ANN) model with a root mean square error of 0.0172 and 0.0167 for COD and NH3-N reduction, respectively. The immobilized adsorbent was regenerated using HCl and was found to be reusable for up to three cycles, promoting material sustainability. This study is aimed to contribute towards SDG 6 and SDG11 by United Nations Sustainable Development Goals.

Influence of CoOx surface passivation and Sn/Zr-co-doping on the photocatalytic activity of Fe2O3 nanorod photocatalysts for bacterial inactivation and photo-Fenton degradation

Hydrothermal and wet impregnation methods are presented in this study for synthesizing CoO_x(1 wt%)/Sn-Zr codoped-Fe₂O₃ nanorod photocatalysts for the degradation of organic pollutants and deactivation of bacteria. A hydrothermal route was used to synthesize self-assembled rod-like hierarchical structures of Sn(0-6%) doped Zr-Fe₂O₃ NRs. Additionally, a wet impregnation method was used to load CoO_x onto the surface of photocatalysts (Sn(0-6%)-doped Zr-Fe₂O₃ NRs). A series of 1 wt% CoO_x modified Sn(0-6%)-doped Zr-Fe₂O₃ NRs were synthesized, characterized, and utilized for the photocatalytic decomposition of organic contaminants, along with the killing of E. coli and S. aureus. In comparison with 0, 2, and 6% Sn co-doped Zr-Fe₂O₃ NRs, the CoO_x(1 wt%)/4%Sn/Zr-Fe₂O₃ NRs photocatalyst exhibited an E. coli and S. aureus inactivation efficiencies (90 and 98%). A bio-TEM study of treated and untreated bacterial cells revealed that the CoO_x(1 wt%)/4%Sn/Zr-Fe₂O₃ NRs photocatalyst led to considerable changes in the bacterial cell membranes' morphology. The optimal CoO_x(1 wt%)/Sn(4%) co-doped Zr-Fe₂O₃ NRs photocatalyst achieved degradation efficiencies of 98.5% and 94.6% for BPA and orange II dye. As a result, this work will provide a facile and effective method for developing visible light-active photocatalysts for bacterial inactivation and organic pollutants degradation.

Photocatalytic and Antimicrobial Properties of Electrospun TiO2-SiO2-Al2O3-ZrO2-CaO-CeO2 Ceramic Membranes

In this study, TiO₂-based ceramic nanofiber membranes in the system of TiO₂-SiO₂-Al₂O₃-ZrO₂-CaO-CeO₂ were synthesized by combining sol-gel and electrospinning processes. In order to investigate the thermal treatment temperature effect, the obtained nanofiber membranes were calcined at different temperatures ranging from 550 to 850 °C. Different characterization methods such as X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FT-IR), and high-resolution transmission electron microscopy (HR-TEM) were conducted on the obtained membranes to investigate the structural and morphological properties of the nanofibers. The Brunauer-Emmett-Teller surface area of the nanofiber membranes was very high (46.6-149.2 m²/g) and decreased with increasing calcination temperature as expected. Photocatalytic activity investigations were determined using methylene blue (MB) as a model dye under UV and sunlight irradiation. High degradation performances were achieved with the calcination temperatures of 650 and 750 °C because of the high specific surface area and the anatase structure of the nanofiber membranes. Moreover, the ceramic membranes showed antibacterial activity against Escherichia coli as a Gram-negative bacterium and Staphylococcus aureus as a Gram-positive bacterium. The superior properties of the novel TiO₂-based multi-oxide nanofiber membranes proved as a promising candidate for various industries, especially the removal of textile dyes from wastewater.

Fe-Ce/Layered Double Hydroxide Heterostructures and Their Derived Oxides: Electrochemical Characterization and Light-Driven Catalysis for the Degradation of Phenol from Water

Fe-Ce/layered double hydroxides (LDHs) were synthesized via a facile route by exploiting the "structural memory" of the LDH when the calcined MgAlLDH and ZnAlLDH were reconstructed in the aqueous solutions of FeSO₄/Ce(SO₄)₂. XRD analysis shows the formation of heterostructured catalysts that entangle the structural characteristics of the LDHs with those of Fe₂O₃ and CeO₂. Furthermore, X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, TG/DTG, SEM/EDX and TEM results reveal a complex morphology defined by the large nano/microplates of the reconstructed LDHs that are tightly covered with nanoparticles of Fe₂O₃ and CeO₂. Calcination at 850 °C promoted the formation of highly crystallized mixed oxides of Fe₂O₃/CeO₂/ZnO and spinels. The photo-electrochemical behavior of Fe-Ce/LDHs and their derived oxides was studied in a three-electrode photo-electrochemical cell, using linear sweep voltammetry (LSV), Mott-Schottky (M-S) analysis and photo-electrochemical impedance spectroscopy (PEIS) measurements, in dark or under illumination. When tested as novel catalysts for the degradation of phenol from aqueous solutions, the light-driven catalytic heterojunctions of Fe-Ce/LDH and their derived oxides reveal their capabilities to efficiently remove phenol from water, under both UV and solar irradiation.

Photocatalytic degradation of Reactive Black dye using ZnO-CeO2 nanocomposites

This study presents the photocatalytic efficiency of ZnO-CeO₂ nanocomposites for the degradation of a model Reactive Black (RB) dye. Nano-CeO₂ was synthesized using cerium nitrate precursor solution via chemical precipitation. Synthesized nano-CeO₂ was mixed with ZnO nanoparticles in different mass ratios to obtain ZnO-CeO₂ heterojunction photocatalyst. The morphology of the nanocomposites was examined using transmission electron microscope (TEM). X-ray diffraction patterns of the CeO₂ corresponded well with (1 1 1) plane of cubic-phase CeO₂. The band gap of the ZnO-CeO₂ nanocatalyst synthesized was determined to be 3.08 eV, which was lower than that of the pristine CeO₂ and ZnO powders, respectively. The results indicate that 1:1 wt. ratio ZnO-CeO₂ nanocomposite provides about 85% RB degradation within 90 min under UV light under alkaline pH conditions. Degradation rate of RB dye achieved with ZnO-CeO₂ nanocomposite was almost 1.5 times greater than that obtained with pristine ZnO. Increasing CeO₂ ratio beyond 1:1 wt. ratio did not significantly increase RB degradation. The results demonstrate that addition of CeO₂ to ZnO results in lowering its band gap energy and aids charge carrier separation resulting in enhanced oxidation of RB dye under UV light.

Photo Energy-Enhanced Oxygen Reduction and Evolution Kinetics in Zn-Air Batteries

Harvesting solar energy directly to boost the sluggish kinetics of oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) on an air cathode is a promising approach. Herein, we synthesize a step-scheme (S-scheme) titanium dioxide-indium selenide (TiO₂-In₂Se₃) heterojunction catalyst. The onset potential in ORR under light illumination reaches 1.28 V and the onset potential decreases to 0.48 V in OER. When an S-scheme TiO₂-In₂Se₃ heterojunction is exposed to light, photogenerated electrons at the conduction band (CB) of TiO₂ migrate to the valence band (VB) of In₂Se₃ due to the built-in electric field. The photogenerated electrons with strong reduction capability on the CB of In₂Se₃ and the holes with strong oxidation capability on the VB of TiO₂ boost the cathode reaction kinetics (ORR/OER). The excellent outcome reveals tremendous commercial potential of photo-enhanced Zn-air batteries.

Transition metal doped CeO2 for photocatalytic removal of 2-chlorophenol in the exposure of indoor white light and antifungal activity

Besides natural sunlight and expensive artificial lights, economical indoor white light can play a significant role in activating a catalyst for photocatalytic removal of organic toxins from contaminated water. In the current effort, CeO₂ has been modified with Ni, Cu, and Fe through doping methodology to study the removal of 2-chlorophenol (2-CP) in the illumination of 70 W indoor LED white light. The absence of additional diffractions due to the dopants and few changes such as reduction in peaks' height, minor peak shift at 2θ (28.525°) and peaks' broadening in XRD patterns of modified CeO₂ verifies the successful doping of CeO₂. The solid-state absorption spectra revealed higher absorbance of Cu-doped CeO₂ whereas a lower absorption response was observed for Ni-doped CeO₂. An interesting observation regarding the lowering of indirect bandgap energy of Fe-doped CeO₂ (∼2.7 eV) and an increase in Ni-doped CeO₂ (∼3.0 eV) in comparison to pristine CeO₂ (∼2.9 eV) was noticed. The process of e ^-- h ⁺ recombination in the synthesized photocatalysts was also investigated through photoluminescence spectroscopy. The photocatalytic studies revealed the greater photocatalytic activity of Fe-doped CeO₂ with a higher rate (∼3.9 × 10^-3 min^-1) among all other materials. Moreover, kinetic studies also revealed the validation of the Langmuir-Hinshelwood kinetic model (R² = 0.9839) while removing 2-CP in the exposure of indoor light with a Fe-doped CeO₂ photocatalyst. The XPS analysis revealed the existence of Fe³⁺, Cu²⁺ and Ni²⁺ core levels in doped CeO₂. Using the agar well-diffusion method, the antifungal activity was assessed against the fungus M. fructicola and F. oxysporum. Compared to CeO₂, Ni-doped CeO₂, and Cu-doped CeO₂ nanoparticles, the Fe-doped CeO₂ nanoparticles have outstanding antifungal properties.

Alternative Strategy to Optimize Cerium Oxide for Enhanced X-ray-Induced Photodynamic Therapy

The emergence of X-ray-induced photodynamic therapy (X-PDT) holds tremendous promise for clinical deep-penetrating cancer therapy. However, the clinical application of X-PDT in cancer treatment is still limited due to the hypoxic property of cancerous tissue, the inherent antioxidant system of tumor cells, and the difficulty in matching the absorption spectra of photosensitizers. Herein, a versatile core-shell radiosensitizer (SCNPs@DMSN@CeO_x-PEG, denoted as SSCP) was elaborately designed and constructed to enhance X-PDT by coating tunable mesoporous silica on nanoscintillators, followed by embedding the cerium oxide nanoparticles in situ. The obtained SSCP radiosensitizer demonstrated a distinct blue-shift in the ultraviolet light region, so that it could perfectly absorb the ultraviolet light converted by the SCNPs core, resulting in the formation of photoinduced electron-hole (e^--h⁺) pairs separation to generate reactive oxygen species (ROS). In addition, the cerium oxide exhibits high glutathione consumption to heighten ROS accumulation, and catalase-like activity to alleviate the hypoxia, which further enhances the efficiency of radiotherapy. Benefiting from the abundant Lu and Ce elements, the computed tomography imaging performance of SSCP is about 3.79-fold that of the clinical contrast agent (iohexol), which has great potential in both preclinical imaging and clinical translation.

A Brief Review of Photocatalytic Reactors Used for Persistent Pesticides Degradation

Pesticide pollution is a major issue, given their intensive use in the 20th century, which led to their accumulation in the environment. At the international level, strict regulations are imposed on the use of pesticides, simultaneously with the increasing interest of researchers from all over the world to find methods of neutralizing them. Photocatalytic degradation is an intensively studied method to be applied for the degradation of pesticides, especially through the use of solar energy. The mechanisms of photocatalysis are studied and implemented in pilot and semi-pilot installations on experimental platforms, in order to be able to make this method more efficient and to identify the equipment that can achieve the photodegradation of pesticides with the highest possible yields. This paper proposes a brief review of the impact of pesticides on the environment and some techniques for their degradation, with the main emphasis on different photoreactor configurations, using slurry or immobilized photocatalysts. This review highlights the efforts of researchers to harmonize the main elements of photocatalysis: choice of the photocatalyst, and the way of photocatalyst integration within photoreaction configuration, in order to make the transfer of momentum, mass, and energy as efficient as possible for optimal excitation of the photocatalyst.

Defect Engineering of Ceria Nanocrystals for Enhanced Catalysis via a High-Entropy Oxide Strategy

Introducing transition-metal components to ceria (CeO₂) is important to tailor the surface redox properties for a broad scope of applications. The emergence of high-entropy oxides (HEOs) has brought transformative opportunities for oxygen defect engineering in ceria yet has been hindered by the difficulty in controllably introducing transition metals to the bulk lattice of ceria. Here, we report the fabrication of ceria-based nanocrystals with surface-confined atomic HEO layers for enhanced catalysis. The increased covalency of the transition-metal-oxygen bonds at the HEO-CeO₂ interface promotes the formation of surface oxygen vacancies, enabling efficient oxygen activation and replenishment for enhanced CO oxidation capabilities. Understanding the structural heterogeneity involving bulk and surface oxygen defects in nanostructured HEOs provides useful insights into rational design of atomically precise metal oxides, whose increased compositional and structural complexities give rise to expanded functionalities.

Engineering Phase Stability of Semimetallic MoS2 Monolayers for Sustainable Electrocatalytic Hydrogen Production

1T'-phase MoS₂ possesses excellent electrocatalytic performance, but due to the instability of the thermodynamic metastable phase, its actual electrocatalytic effect is seriously limited. Here, we report a wet-chemical synthesis strategy for constructing rGO/1T'-MoS₂/CeO₂ heterostructures to improve the phase stability of metastable 1T' phase MoS₂ monolayers. Importantly, the rGO/1T'-MoS₂/CeO₂ heterostructure exhibits excellent electrocatalytic hydrogen evolution reaction (HER) performance, which is much better than the 1T'-MoS₂ monolayers. The synergistic effects between CeO₂ nanoparticles (NPs) and 1T'-MoS₂ monolayers were systematically investigated. 1T'-MoS₂ monolayers combined with the cocatalyst of CeO₂ NPs can produce lattice strain and distortion on 1T'-MoS₂ monolayers, which can tune the energy band structure, charge transfer, and energy barriers of hydrogen atom adsorption (ΔE_H), leading to promotion of the phase activity and stability of 1T'-MoS₂ monolayers for hydrogen production. Our work offers a feasible method for the preparation of efficient HER electrocatalysts based on the engineering phase stability of metastable materials.

Exploring the Influence of Synthesis Parameters on the Optical Properties for Various CeO2 NPs

Cerium oxide (CeO₂) nanoparticles were synthesized with a chemical precipitation method in different experimental conditions using cerium nitrate hexahydrate (Ce(NO₃)₃·6H₂O) as a precursor, modifying the solution pH, the reaction time, and Co atoms as dopants, in order to tune the band gap energy values of the prepared samples. The physical characteristics of the synthesized ceria nanoparticles were evaluated by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV–Vis analyses and photoluminescence measurements. XRD data revealed a pure cubic fluorite structure of CeO₂ NPs, the estimation of crystallite sizes by Scherrer’s formula indicates the formation of crystals with dimensions between 11.24 and 21.65 nm. All samples contain nearly spherical CeO₂ nanoparticles, as well as cubic, rhomboidal, triangular, or polyhedral nanoparticles that can be identified by TEM images. The optical investigation of CeO₂ samples revealed that the band gap energy values are between 3.18 eV and 2.85 eV, and, after doping with Co atoms, the E_g of samples decreased to about 2.0 eV. In this study, we managed to obtain CeO₂ NPs with E_g under 3.0 eV by only modifying the synthesis parameters. In addition, by doping with Co ions, the band gap energy value was lowered to 2.0 eV. This aspect leads to promising results that provide an encouraging approach for future photocatalytic investigations.

Ultrasonic-assisted decoration of Ag2WO4, AgI, and Ag nanoparticles over tubular g-C3N4: Plasmonic photocatalysts for impressive removal of tetracycline under visible light

The development of an efficient, eco-friendly, and low-cost photocatalyst is essential for addressing environmental and energy crises. In this regard, we report novel plasmonic photocatalysts through adorning tubular g-C₃N₄ with Ag₂WO₄, Ag, and AgI nanoparticles (TGCN/Ag/Ag₂WO₄/AgI) fabricated via a facile ultrasonic-irradiation procedure. The TGCN/Ag/Ag₂WO₄/AgI (20%) nanocomposite presented the excellent photocatalytic ability for removal of tetracycline hydrochloride under visible light, which was almost 45.6, 4.03, and 1.32 times more than GCN, TGCN, and TGCN/Ag/Ag₂WO₄ (20%) photocatalysts, respectively. Interestingly, the photocatalyst displayed impressive ability for the degradations of amoxicilline, rhodamine B, methyl orange, fuchsine, and methylene blue, which was 14.7, 52.2, 9.8, 13.2, and 7.46 times as much as pure GCN. The outcomes of DRS, PL, EIS, and photocurrent density analyses proved that the impressive activity could be related to the highly promoted harvesting of visible light, segregation of charge carriers, and improved charge migrations. In addition, trapping tests exhibited that ^•O₂^- and h⁺ were active species in the photocatalysis process.