Recent development of fiber-optic chemical sensors and biosensors: Mechanisms, materials, micro/nano-fabrications and applications

Multimode interference methane sensor based on a ZIF-8/PDMS composite film

A multimode interference methane sensor based on a ZIF-8/PDMS composite film is proposed. The sensing principle is that the refractive index of the ZIF-8/PDMS composite film changes when it adsorbs methane, leading to a measurable optical path difference during the coupling of the cladding higher-order modes and the fundamental mode in the multimode interference fiber (MMI). The environmental methane concentration is then detectable by detecting the wavelength shifts of the interference peaks in the resulted spectrum. Through simulations and experiments aimed at enhancing sensor sensitivity, we optimized three parameters within the sensor structure: the length of the Tapered Single-Mode Fiber (TSMF), the composite film thickness, and the TSMF taper diameter. The experimental results indicate that the sensor's sensitivity reaches a maximum of 0.231 nm%-1. Additionally, the sensor exhibits excellent structural stability and measurement repeatability. The response time is as short as 40 s, and the recovery time ranges between 3 and 5 min. The proposed multimode interferometric methane sensor based on the ZIF-8/PDMS composite film has great potential to support highly sensitive methane concentration detection in many applications.

Optical fiber immunosensors based on surface plasmon resonance for the detection of Escherichia coli

Every year, millions of people suffer some form of illness associated with the consumption of contaminated food. Escherichia coli (E. coli), found in the intestines of humans and other animals, is commonly associated with various diseases, due to the existence of pathogenic strains. Strict monitoring of food products for human consumption is essential to ensure public health, but traditional cell culture-based methods are associated with long waiting times and high costs. New approaches must be developed to achieve cheap, fast, and on-site monitoring. Thus, in this work, we developed optical fiber sensors based on surface plasmon resonance. Gold and cysteamine-coated fibers were functionalized with anti-E. coli antibody and tested using E. coli suspensions with concentrations ranging from 1 cell/mL to 105 cells/mL. An average logarithmic sensitivity of 0.21 ± 0.01 nm/log(cells/mL) was obtained for three independent assays. An additional assay revealed that including molybdenum disulfide resulted in an increase of approximately 50% in sensitivity. Specificity and selectivity were also evaluated, and the sensors were used to analyze contaminated water samples, which verified their promising applicability in the aquaculture field.

Recent Advances in Nanomaterials Based Optical Sensors for the Detection of Melatonin and Serotonin

In this review paper we discussed the detection of melatonin and serotonin by using various optical methods. Melatonin and serotonin are very necessary body hormones these are also called neuroregulatory hormones secreted by pineal gland in brain by pinealocytes and shape of pineal gland is cone like. Sensitive detection of melatonin and serotonin in pharmacological samples and human serum is crucial for human beings, lots of research publications available in literature for melatonin and serotonin and we overviewed these papers. We have deeply reviewed many research papers where sensitively sensing of melatonin and serotonin occurs, by using of various interfering agents and nanomaterials. This review aims presenting colorimetry, fluorometry and spectrophotometric detection of melatonin (MEL) and serotonin (SER) by using different metal oxides, carbon nanomaterials (nanosheets, nanorods, nanofibers) and many other agents. Nanomaterials typically possess favourable optical, electrical and mechanical characteristics, they provide up new avenues for enhancing the efficacy of sensors. It is crucial to provide an optical sensors platform that is dependable, sensitive and low price. The development of sensors and biosensors to use nanomaterials for neurotransmitters has advanced significantly in recent years. There are currently many developing biomarkers in biological fluids, and bionanomaterial-based biosensor systems, as well as clinical and pharmacological settings, have garnered significant interest. Biomarkers have been found using optical devices in a quick, selective and sensitive manner. Our aim is to compile all the data that already published on MEL, SER sensing and comparison of each method, we mainly focused on principle, observations, sensitivity, selectivity, limit of detection, mechanism behind the reaction, effect of temperature, pH and concentration. In the last of this paper, we discuss some challenges of these methods and future projects.

Tailored Polypyrrole Nanofibers as Ion-to-Electron Transduction Membranes for Wearable K+ Sensors

Conductive polymers are recognized as ideal candidates for the development of noninvasive and wearable sensors for real-time monitoring of potassium ions (K+ ) in sweat to ensure the health of life. However, the low ion-to-electron transduction efficiency and limited active surface area hamper the development of high-performance sensors for low-concentration K+ detection in the sweat. Herein, a wearable K+ sensor is developed by tailoring the nanostructure of polypyrrole (PPy), serving as an ion-to-electron transduction layer, for accurately and stably tracing the K+ fluctuation in human sweat. The PPy nanostructures can be tailored from nanospheres to nanofibers by controlling the supramolecular assembly process during PPy polymerization. Resultantly, the ion-to-electron transduction efficiency (17-fold increase in conductivity) and active surface area (1.3-fold enhancement) are significantly enhanced, accompanied by minimized water layer formation. The optimal PPy nanofibers-based K+ sensor achieved a high sensitivity of 62 mV decade-1 , good selectivity, and solid stability. After being integrated with a temperature sensor, the manufactured wearable sensor realized accurate monitoring of K+ fluctuation in the human sweat.

Recent Trends in Chemical Sensors for Detecting Toxic Materials

Industrial development has led to the widespread production of toxic materials, including carcinogenic, mutagenic, and toxic chemicals. Even with strict management and control measures, such materials still pose threats to human health. Therefore, convenient chemical sensors are required for toxic chemical monitoring, such as optical, electrochemical, nanomaterial-based, and biological-system-based sensors. Many existing and new chemical sensors have been developed, as well as new methods based on novel technologies for detecting toxic materials. The emergence of material sciences and advanced technologies for fabrication and signal-transducing processes has led to substantial improvements in the sensing elements for target recognition and signal-transducing elements for reporting interactions between targets and sensing elements. Many excellent reviews have effectively summarized the general principles and applications of different types of chemical sensors. Therefore, this review focuses on chemical sensor advancements in terms of the sensing and signal-transducing elements, as well as more recent achievements in chemical sensors for toxic material detection. We also discuss recent trends in biosensors for the detection of toxic materials.

Design and fabrication of a simple and cost-effective optical flow meter using liquid crystals and textile grid

The measurement of airflow velocity is crucial in various fields, and several sensing approaches have been developed for detecting airflow, including optical fiber-based flowmeters. However, these sensors often require complex fabrication processes and precise optical alignment. In this paper, a simpler and more cost-effective approach has been used to measure air flow rate by utilizing the birefringence property of liquid crystals (LCs). LCs possess distinct optical characteristics, and their reorientation due to airflow can be detected by observing the intensity of the output light between crossed polarizers. The novelty of this study is the utilization of a textile grid to hold the LC layer, which simplifies the fabrication process. This LC-based gas flowmeter offers a simple, low-cost setup and provides rapid performance. This research presents what we believe to be a new approach to calculate airflow by exploiting the optical properties of LCs, which is a new frontier in gas flow measurement. The proposed airflow meter is capable of detecting airflow rates ranging from 0 l/min to 7.5 l/min with an accuracy of 0.5 l/min. It exhibits a stable response time in 75 seconds, and the sensor maintains acceptable stability over time.

Sensing characteristics of structural microfiber long-period gratings

We present a detailed investigation into the sensing characteristics of a structural microfiber long-period grating (mLPG) sensor. By spirally winding a thinner microfiber to another thicker microfiber, periodic refractive index modulation is formed while the optical signal transmitted in the thicker microfiber is resonantly coupled out to the thinner microfiber, and then a 5-period four-port mLPG can be obtained with a device length of only ∼570 µm demonstrated a strong resonant dip of 25 dB. We studied the sensitivity characteristics of the four-port mLPG with surrounding strain, force, temperature and refractive index, and the obtained sensitivities were -6.4 pm/µɛ, -8418.6 nm/N, 7.62 pm/°C and 2122 nm/RIU, respectively. With the advantages of high refractive index sensitivity and wide wavelength tunable range, the four-port mLPG has great potential in applications such as tunable filters and biochemical sensor.

Temperature-Compensated Solution Concentration Measurements Using Photonic Crystal Fiber-Tip Sensors

We demonstrate fiber optic sensors with temperature compensation for the accurate measurement of ethanol concentration in aqueous solutions. The device consists of two photonic crystal (PhC) fiber-tip sensors: one measures the ethanol concentration via refractive index (RI) changes and the other one is isolated from the liquid for the independent measurement of temperature. The probes utilize an optimized PhC design providing a Lorentzian-like, polarization-independent response, enabling a very low imprecision (pm-level) in the wavelength determination. By combining the information from the two probes, it is possible to compensate for the effect that the temperature has on the concentration measurement, obtaining more accurate estimations of the ethanol concentration in a broad range of temperatures. We demonstrate the simultaneous and single-point measurements of temperature and ethanol concentration in water, with sensitivities of 19 pm/°C and ∼53 pm/%, in the ranges of 25 °C to 55 °C and 0 to 50% (at 25 °C), respectively. Moreover, a maximum error of 1.1% in the concentration measurement, with a standard deviation of ≤0.8%, was obtained in the entire temperature range after compensating for the effect of temperature. A limit of detection as low as 0.08% was demonstrated for the concentration measurement in temperature-stable conditions.

Laser frequency noise correction in LFM-based interferometric fiber-optic hydrophone array

In this paper, we propose a novel time-division multiplexed (TDM) array for a large-scale interferometric fiber-optic hydrophone system, in which we introduce a power-optimized reference probe and effectively reduce the additional white noise while correcting for light source frequency noise. Laser frequency noise usually introduces appreciable phase noise during demodulation of interferometric fiber-optic hydrophones. In the previous means, one would introduce an additional probe isolated from the environment in sensor array, and use it as a reference to calibrate the demodulation results of the other actual sensors. However, while correcting, the reference probe also introduces a large white noise. In our array, the echo of the reference probe is higher than the other sensors, thus solving this problem. The novel array design is applied to our previously proposed fiber-optic hydrophone based on a linear frequency modulated (LFM) light source. Experiments show that the deterioration of phase noise floor caused by additional white noise is improved from at least 3 dB originally to within 1 dB. This paper analyzes the factors that need to be concerned for the successful implementation of correction algorithms in hydrophone systems based on LFM sources. Particular focus is given to the impact of the power optimization of reference probe on the white noise and the corrected phase noise. Our proposal allows a significant relaxation of the demanding linewidth requirement for interferometric hydrophone. It is shown that laser with linewidth of 338.06 MHz can replace that with 1.417 kHz in our new system, while achieves the same demodulation noise floor.

Biocompatible polymer optical fiber with a strongly scattering spherical end for interstitial photodynamic therapy

Interstitial photodynamic therapy (I-PDT), which utilizes optical fibers to deliver light for photosensitizer excitation and the elimination of penetration depth limitation, is a promising modality in the treatment of deeply seated tumors or thick tumors. Currently, the excitation domain of the optical fiber is extremely limited, restricting PDT performance. Here, we designed and fabricated a biocompatible polymer optical fiber (POF) with a strongly scattering spherical end (SSSE) for I-PDT applications, achieving an increased excitation domain and consequently excellent in vitro and in vivo therapeutical outcomes. The POF, which was drawn using a simple thermal drawing method, was made of polylactic acid, ensuring its superior biocompatibility. The excitation domains of POFs with different ends, including flat, spherical, conical, and strongly scattering spherical ends, were analyzed and compared. The SSSE was achieved by introducing nanopores into a spherical end, and was further optimized to achieve a large excitation domain with an even intensity distribution. The optimized POF enabled outstanding therapeutic performance of I-PDT in in vitro cancer cell ablation and in vivo anticancer therapy. All of its notable optical features, including low transmission/bending loss, superior biocompatibility, and a large excitation domain with an even intensity distribution, endow the POF with great potential for clinical I-PDT applications.

Various Types of Light Guides for Use in Lossy Mode Resonance-Based Sensors

A comparative study of figure-of-merit fiber sensors of the mass concentration of NaCl solutions based on single-mode and multi-mode fibers was carried out. Lossy mode resonance is realized on chemically thinned sections of optical fibers to various diameters (from 26 to 100 μm) coated with ZnTe. Thin-film coatings were applied using the method of metalorganic chemical vapor deposition (MOCVD). Samples of single-mode and multi-mode fiber sensors were created in such a way that the depth and spectral position of resonances in aqueous NaCl solutions coincided. Sensors implemented on a single-mode fiber have a higher sensitivity (5930 nm/refractive index unit (RIU)) compared to those on a multi-mode fiber (4860 nm/RIU) and a smaller half-width of the resonance in the transmission spectrum. According to the results of experiments, figure-of-merit sensors are in the range of refractive indices of 1.33-1.35 for: multi-mode fiber-25 RIU^-1, single-mode fiber-75 RIU^-1. The sensitivity of the resulting sensors depends on the surface roughness of the ZnTe coating. The roughness of films synthesized on a single-mode fiber is four times higher than this parameter for a coating on a multi-mode fiber. For the first time, in the transmission spectrum during the synthesis of a thin-film coating on a multi-mode fiber, the possibility of separating the first nine orders of resonances into electric and magnetic transverse components has been demonstrated. The characteristics of sensors with the operating wavelength range in the visible (500-750 nm) and infrared (1350-1550 nm) regions of the spectrum are compared. The characteristics of multi-mode lossy mode resonance sensors are demonstrated, which make them more promising for use in applied devices than for laboratory research.

Optical fiber pH sensor based on a multimode interference device with polymer overlay

An optical fiber pH sensor based on a multimode interference structure is presented. The sensitive element is a piece of no-core fiber (NCF) coated with a mixture of polyallylamine hydrochloride and polyacrylic acid by a modified layer-by-layer (LbL) self-assembly method. It is experimentally shown that by reducing the diameter of the NCF by chemical etching, the sensitivity is increased from -0.31n m/p H to -2n m/p H. The sensor exhibits a high linear response of 0.997 over a pH range from 5 to 11.3 with a rapid response time lower than 1 s.

Micro/Nano-Fabrication of Flexible Poly(3,4-Ethylenedioxythiophene)-Based Conductive Films for High-Performance Microdevices

With the increasing demands for novel flexible organic electronic devices, conductive polymers are now becoming the rising star for reaching such targets, which has witnessed significant breakthroughs in the fields of thermoelectric devices, solar cells, sensors, and hydrogels during the past decade due to their outstanding conductivity, solution-processing ability, as well as tailorability. However, the commercialization of those devices still lags markedly behind the corresponding research advances, arising from the not high enough performance and limited manufacturing techniques. The conductivity and micro/nano-structure of conductive polymer films are two critical factors for achieving high-performance microdevices. In this review, the state-of-the-art technologies for developing organic devices by using conductive polymers are comprehensively summarized, which will begin with a description of the commonly used synthesis methods and mechanisms for conductive polymers. Next, the current techniques for the fabrication of conductive polymer films will be proffered and discussed. Subsequently, approaches for tailoring the nanostructures and microstructures of conductive polymer films are summarized and discussed. Then, the applications of micro/nano-fabricated conductive films-based devices in various fields are given and the role of the micro/nano-structures on the device performances is highlighted. Finally, the perspectives on future directions in this exciting field are presented.

A Fiber Bragg Grating Sensor Based on Cladding Mode Resonance for Label-Free Biosensing

A fiber-optic biosensing platform based on ultra-narrowband cladding mode resonances was developed on a high-reflectivity fiber Bragg grating (FBG) for targeting biomolecular detection. The multiple cladding modes with a high sensitivity to the refractive index (RI) were excited in the FBG by coupling between the forward-propagating guided core mode of the multimode fiber and the backward-propagating guided cladding mode of the FBG without any damage to the fiber structure or any change to the standard FBG manufacturing process. The full width at half maximum and the Q-factor of the typical cladding mode resonance operation of the proposed sensor are 80 pm and 19,270, respectively, which are better than those of most fiber-optic biosensors reported to date. In addition, the FBG sensor demonstrated a high sensitivity in protein detection and a high selectivity in serum sample assays. The sensitivity of this sensor was further increased simply by coating it with graphene oxide (GO) sheets on the sensing surface without using a signal amplification strategy. Furthermore, an ultra-low limit of detection (LOD) of 32 pM was obtained by the GO-coated FBG sensor for IgG detection. The proposed FBG sensor provides a competitive fiber-optic platform for biomolecular detection. It has a great potential for applications in label-free biosensing.

Analysis of the Polymer Two-Layer Protective Coating Impact on Panda-Type Optical Fiber under Bending

The article discusses the effects of thermal-force on the Panda-type optical fiber. The studies used a wide temperature range. The research used two thermal cycles with exposures to temperatures of 23, 60 and −60 °C. The field of residual stresses in the fiber formed during the drawing process was determined and applied. Panda was considered taking into account a two-layer viscoelastic polymer coating under conditions of tension winding on an aluminum coil in the framework of a contact problem. The paper investigated three variants of coil radius to analyze the effect of bending on fiber behavior. The effect of the coating thickness ratio on the system deformation and optical characteristics was analyzed. Qualitative and quantitative patterns of the effect of temperature, bending, thickness of individual polymer coating layers and relaxation transitions of their materials on the Panda optical fiber deformation and optical characteristics were established. Assessment of approaches to the calculation of optical characteristics (values of the refractive indices and fiber birefringence) are given in the framework of the study. The patterns of deformation and optical behavior of the Panda-type fiber with a protective coating, taking into account the nonlinear behavior of the system materials, were original results.

Ultralow Limit Detection of Soluble HER2 Biomarker in Serum with a Fiber-Optic Ball-Tip Resonator Assisted by a Tilted FBG

An optical-fiber biosensor has been developed for the detection of the breast cancer biomarker soluble human epidermal growth factor receptor-2 (sHER2). The sensor was fabricated by combining a tilted fiber Bragg grating (TFBG) with a ball resonator, allowing us to achieve an excellent sensitivity compared to other optical-fiber-based sensors. The sensor exhibits a resonance comb excited by the TFBG and the spectral profile of the ball resonator. The detection of sHER2 at extremely low concentrations was carried out by tracking the amplitude change of selected resonances. The therapeutic anti-HER2 monoclonal antibody Trastuzumab has been used to functionalize the biosensor with silane surface chemistry. The sensor features a sensitivity of 4034 dB/RIU with a limit of detection (LoD) in buffer and in a 1/10 diluted serum of 151.5 ag/mL and 3.7 pg/mL, respectively. At relatively high protein concentrations (64 ng/mL) binding to sHER (7.36 dB) as compared to control proteins (below 0.7 dB) attested the high specificity of sHER2 detection.

Relevance of the Spectral Analysis Method of Tilted Fiber Bragg Grating-Based Biosensors: A Case-Study for Heart Failure Monitoring

Optical fiber technology has rapidly progressed over the years, providing valuable benefits for biosensing purposes such as sensor miniaturization and the possibility for remote and real-time monitoring. In particular, tilted fiber Bragg gratings (TFBGs) are extremely sensitive to refractive index variations taking place on their surface. The present work comprises a case-study on the impact of different methods of analysis applied to decode spectral variations of bare and plasmonic TFBGs during the detection of N-terminal B-type natriuretic peptide (NT-proBNP), a heart failure biomarker, namely by following the most sensitive mode, peaks of the spectral envelopes, and the envelopes’ crossing point and area. Tracking the lower envelope resulted in the lowest limits of detection (LOD) for bare and plasmonic TFBGs, namely, 0.75 ng/mL and 0.19 ng/mL, respectively. This work demonstrates the importance of the analysis method on the outcome results, which is crucial to attain the most reliable and sensitive method with lower LOD sensors. Furthermore, it makes the scientific community aware to take careful attention when comparing the performance of different biosensors in which different analysis methods were used.

Fast-Response Oxygen Optical Fiber Sensor based on PEA2 SnI4 Perovskite with Extremely Low Limit of Detection

Oxygen sensor is an important technique in various applications including industrial process control, medical equipment, biological fabrication, etc. The reported optical fiber-based configurations so far, using gas-sensitive coating do not meet the stringent performance targets, such as fast response time and low limit of detection (LOD). Tin-based halide perovskites are sensitive to oxygen with potential use for sensor applications. Here, the halide perovskite-based oxygen optical fiber sensor by combining phenylethylammonium tin iodide (PEA₂ SnI₄ ) and tilted fiber Bragg grating (TFBG) is demonstrated. The PEA₂ SnI₄ -based oxygen optical fiber sensor is reversible at room temperature with a response time of about 10 s, and the experimental LOD approaches to an extremely low oxygen concentration of about 50 ppm. The as-fabricated oxygen sensor shows a relative response change of 0.6 dB for an oxygen concentration increase from 50 ppm to 5% with good gas selection against NO₂ , CO, CO₂ , H₂ . This work extends the sensor applications of halide perovskites, providing a novel technique for rapid and repeatable oxygen gas detection at a low level.

Progress on Optical Fiber Biochemical Sensors Based on Graphene

Graphene, a novel form of the hexagonal honeycomb two-dimensional carbon-based structural material with a zero-band gap and ultra-high specific surface area, has unique optoelectronic capabilities, promising a suitable basis for its application in the field of optical fiber sensing. Graphene optical fiber sensing has also been a hotspot in cross-research in biology, materials, medicine, and micro-nano devices in recent years, owing to prospective benefits, such as high sensitivity, small size, and strong anti-electromagnetic interference capability and so on. Here, the progress of optical fiber biochemical sensors based on graphene is reviewed. The fabrication of graphene materials and the sensing mechanism of the graphene-based optical fiber sensor are described. The typical research works of graphene-based optical fiber biochemical sensor, such as long-period fiber grating, Bragg fiber grating, no-core fiber and photonic crystal fiber are introduced, respectively. Finally, prospects for graphene-based optical fiber biochemical sensing technology will also be covered, which will provide an important reference for the development of graphene-based optical fiber biochemical sensors.

A Review of Optical Fibre Ethanol Sensors: Current State and Future Prospects

A range of optical fibre-based sensors for the measurement of ethanol, primarily in aqueous solution, have been developed and are reviewed here. The sensing approaches can be classified into four groups according to the measurement techniques used, namely absorption (or absorbance), external interferometric, internal fibre grating and plasmonic sensing. The sensors within these groupings can be compared in terms of their characteristic performance indicators, which include sensitivity, resolution and measurement range. Here, particular attention is paid to the potential application areas of these sensors as ethanol production is globally viewed as an important industrial activity. Potential industrial applications are highlighted in the context of the emergence of the internet of things (IoT), which is driving widespread utilization of these sensors in the commercially significant industrial and medical sectors. The review concludes with a summary of the current status and future prospects of optical fibre ethanol sensors for industrial use.

Chip-scale optical airflow sensor

Airflow sensors are an essential component in a wide range of industrial, biomedical, and environmental applications. The development of compact devices with a fast response and wide measurement range capable of in situ airflow monitoring is highly desirable. Herein, we report a miniaturized optical airflow sensor based on a GaN chip with a flexible PDMS membrane. The compact GaN chip is responsible for light emission and photodetection. The PDMS membrane fabricated using a droplet-based molding process can effectively transform the airflow stimuli into optical reflectance changes that can be monitored by an on-chip photodetector. Without the use of external components for light coupling, the proposed sensor adopting the novel integration scheme is capable of detecting airflow rates of up to 53.5 ms^-1 and exhibits a fast response time of 12 ms, holding great promise for diverse practical applications. The potential use in monitoring human breathing is also demonstrated.

Rapid and quantitative detection of SARS-CoV-2 IgG antibody in serum using optofluidic point-of-care testing fluorescence biosensor

The COVID-19 pandemic brings unprecedented crisis for public health and economics in the world. Detecting specific antibodies to SARS-CoV-2 is a powerful supplement for the diagnosis of COVID-19 and is important for epidemiological studies and vaccine validations. Herein, a rapid and quantitative detection method of anti-SARS-CoV-2 IgG antibody was built based on the optofluidic point-of-care testing fluorescence biosensor. Without complicated steps needed, the portable system is suitable for on-site sensitive determination of anti-SARS-CoV-2 IgG antibody in serum. Under the optimal conditions, the whole detection procedure is about 25 min with a detection limit of 12.5 ng/mL that can well meet the diagnostic requirements. The method was not obviously affected by IgM and serum matrix and demonstrated to have good stability and reliability in real sample analysis. Compared to ELISA test results, the proposed method exhibits several advantages including wider measurement range and easier operation. The method provides a universal platform for rapid and quantitative analysis of other related biomarkers, which is of significance for the prevention and control of COVID-19 pandemic.

Organic/Inorganic Self-Assembled Hybrid Nano-Architectures for Cancer Therapy Applications

Since the conceptualization of nanomedicine, numerous nanostructure-mediated drug formulations have progressed into clinical trials for treating cancer. However, recent clinical trial results indicate such kind of drug formulations has a limited improvement on the antitumor efficacy. This is due to the biological barriers associated with those formulations, for example, circulation stability, extravasation efficiency in tumor, tumor penetration ability, and developed multi-drug resistance. When employing for nanomedicine formulations, pristine organic-based and inorganic-based nanostructures have their own limitations. Accordingly, organic/inorganic (O/I) hybrids have been developed to integrate the merits of both, and to minimize their intrinsic drawbacks. In this context, the recent development in O/I hybrids resulting from a self-assembly strategy will be introduced. Through such a strategy, organic and inorganic building blocks can be self-assembled via either chemical covalent bonds or physical interactions. Based on the self-assemble procedure, the hybridization of four organic building blocks including liposomes, micelles, dendrimers, and polymeric nanocapsules with five functional inorganic nanoparticles comprising gold nanostructures, magnetic nanoparticles, carbon-based materials, quantum dots, and silica nanoparticles will be highlighted. The recent progress of these O/I hybrids in advanced modalities for combating cancer, such as, therapeutic agent delivery, photothermal therapy, photodynamic therapy, and immunotherapy will be systematically reviewed.

Laser nano-filament explosion for enabling open-grating sensing in optical fibre

Embedding strong photonic stopbands into traditional optical fibre that can directly access and sense the outside environment is challenging, relying on tedious nano-processing steps that result in fragile thinned fibre. Ultrashort-pulsed laser filaments have recently provided a non-contact means of opening high-aspect ratio nano-holes inside of bulk transparent glasses. This method has been extended here to optical fibre, resulting in high density arrays of laser filamented holes penetrating transversely through the silica cladding and guiding core to provide high refractive index contrast Bragg gratings in the telecommunication band. The point‐by‐point fabrication was combined with post-chemical etching to engineer strong photonic stopbands directly inside of the compact and flexible fibre. Fibre Bragg gratings with sharply resolved π-shifts are presented for high resolution refractive index sensing from \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${n}_{{{{{{\rm{H}}}}}}}$$\end{document}nH = 1 to 1.67 as the nano-holes were readily wetted and filled with various solvents and oils through an intact fibre cladding.

Engineered stop bands to sense an ambient environment can enable many applications. Here, the authors demonstrate well-controlled processes to open high-aspect ratio nanoholes through optical fibre for Bragg gratings in the telecomm spectrum and to enable high-resolution refractive index sensing

Recent Advances in the Use of Mesoporous Silica Nanoparticles for the Diagnosis of Bacterial Infections

Public awareness of infectious diseases has increased in recent months, not only due to the current COVID-19 outbreak but also because of antimicrobial resistance (AMR) being declared a top-10 global health threat by the World Health Organization (WHO) in 2019. These global issues have spiked the realization that new and more efficient methods and approaches are urgently required to efficiently combat and overcome the failures in the diagnosis and therapy of infectious disease. This holds true not only for current diseases, but we should also have enough readiness to fight the unforeseen diseases so as to avoid future pandemics. A paradigm shift is needed, not only in infection treatment, but also diagnostic practices, to overcome the potential failures associated with early diagnosis stages, leading to unnecessary and inefficient treatments, while simultaneously promoting AMR. With the development of nanotechnology, nanomaterials fabricated as multifunctional nano-platforms for antibacterial therapeutics, diagnostics, or both (known as "theranostics") have attracted increasing attention. In the research field of nanomedicine, mesoporous silica nanoparticles (MSN) with a tailored structure, large surface area, high loading capacity, abundant chemical versatility, and acceptable biocompatibility, have shown great potential to integrate the desired functions for diagnosis of bacterial infections. The focus of this review is to present the advances in mesoporous materials in the form of nanoparticles (NPs) or composites that can easily and flexibly accommodate dual or multifunctional capabilities of separation, identification and tracking performed during the diagnosis of infectious diseases together with the inspiring NP designs in diagnosis of bacterial infections.

A Magnetic Field SPR Sensor Based on Temperature Self-Reference

In this paper, a novel D-shaped photonic crystal fiber sensor for simultaneous measurements of magnetic field and temperature is proposed and characterized. Based on the surface plasmon resonance theory, the D-shaped flat surface coated with a gold layer is in direct contact with magnetic fluid to detect magnetic field, and one of the relatively small air holes near the fiber core is filled with polydimethylsiloxane (PDMS) to sense temperature. The realization of measuring the magnetic field and temperature separately through two channels depends on the fact that the magnetic field only changes the refractive index of the magnetic fluid, but has no effect on the refractive index of PDMS. The refractive index of the magnetic fluid and PDMS can be affected by temperature at the same time. The sensor designed in this work can separate the variations of the magnetic field and temperature simultaneously, therefore solving the cross-sensitivity problem to further improve the magnetic field sensitivity. When the thickness of the gold film is 50 nm and the radius of the filling hole is 0.52 µm, the magnetic field sensitivity and the temperature sensitivity of magnetic field sensor based on temperature self-reference can reach 0.14274 nm/Oe and −0.229 nm/°C, respectively.

Immunosensing Based on Optical Fiber Technology: Recent Advances

The evolution of optical fiber technology has revolutionized a variety of fields, from optical transmission to environmental monitoring and biomedicine, given their unique properties and versatility. For biosensing purposes, the light guided in the fiber core is exposed to the surrounding media where the analytes of interest are detected by different techniques, according to the optical fiber configuration and biofunctionalization strategy employed. These configurations differ in manufacturing complexity, cost and overall performance. The biofunctionalization strategies can be carried out directly on bare fibers or on coated fibers. The former relies on interactions between the evanescent wave (EW) of the fiber and the analyte of interest, whereas the latter can comprise plasmonic methods such as surface plasmon resonance (SPR) and localized SPR (LSPR), both originating from the interaction between light and metal surface electrons. This review presents the basics of optical fiber immunosensors for a broad audience as well as the more recent research trends on the topic. Several optical fiber configurations used for biosensing applications are highlighted, namely uncladded, U-shape, D-shape, tapered, end-face reflected, fiber gratings and special optical fibers, alongside practical application examples. Furthermore, EW, SPR, LSPR and biofunctionalization strategies, as well as the most recent advances and applications of immunosensors, are also covered. Finally, the main challenges and an outlook over the future direction of the field is presented.

Optoelectronic Instrumentation and Measurement Strategies for Optical Chemical (Bio)Sensing

There is a growing interest in the development of sensitive, portable, and low-cost instrumentation for optical chemical (bio)sensing. Such instrumentation can allow real-time decision-making for industry, farmers, and researchers. The combination of optical fiber schemes, luminescence spectroscopy techniques, and new materials for sensor immobilization has allowed the growth of optical sensors. This article focuses on the development of low-cost optoelectronic instrumentation and measurement strategies for optical chemical (bio)sensing. Most of the articles in this field have focused on the chemical sensors themselves, although few have covered the design process for optoelectronic instrumentation. This article tries to fill this gap by presenting designs for real applications, as carried out by the authors. We also offer an introduction to the optical devices and optical measurement techniques used in this field to allow a full understanding of the applications.

Fabrication of Optical Fibers with Multiple Coatings for Swelling-Based Chemical Sensing

We discuss distributed chemical sensing based on the swelling of coatings of optical fibers. Volume changes in the coating induce strain in the fiber's glass core, provoking a local change in the refractive index which is detectable by distributed fiber optical sensing techniques. We describe methods to realize different coatings on a single fiber. Simultaneous detection of swelling processes all along the fiber opens the possibility to interrogate thousands of differently functionalized sections on a single fiber. Principal component analysis is used to enable sensors for environmental monitoring, food analysis, agriculture, water quality monitoring, or medical diagnostics.

Advances in diagnosis of Helicobacter pylori through biosensors: Point of care devices

Invasive as well as non-invasive conventional techniques for the detection of Helicobacter pylori (H. pylori) have several limitations that are being overcome by the development of novel, rapid and reliable biosensors. Herein, we describe several biosensors fabricated for the detection of H. pylori. This review aims to provide the principles of biosensors and their components including in the context to H. pylori detection. The major biorecognition elements in H. pylori detection include antigen/antibodies, oligonucleotides and enzymes. Furthermore, the review describes the transducers, such as electrochemical, optical and piezoelectric, also including microfluidics approaches. An overview of the biomarkers associated with H. pylori pathogenesis is also discussed. Finally, the prospects of advancement and commercialization of point-of-care tools are summarized.

All Silica Micro-Fluidic Flow Injection Sensor System for Colorimetric Chemical Sensing

This paper presents a miniature, all-silica, flow-injection sensor. The sensor consists of an optical fiber-coupled microcell for spectral absorption measurements and a microfluidic reagent injection system. The proposed sensor operates in back reflection mode and, with its compact dimensions, (no more than 200 µm in diameter) enables operation in small spaces and at very low flow rates of analyte and reagent, thus allowing for on-line or in-line colorimetric chemical sensing.

Harmonic optical microfiber Bragg grating immunosensor for the accelerative test of cardiac biomarker (cTn-I)

Fiber-optic biosensor has shown tremendous promise in probing cardiac biomarkers label-free and in-operando. However, temperature cross-sensitivity is ubiquitously found and impedes further advances of the fiber-optic biosensors, especially for the scenario of rapid test at-body. In this study, we exploit a new regime that harnesses the harmonic resonances of a single microfiber Bragg grating to rule out the impact of the thermal noise. The reflections yielded by the harmonics can be engineered simultaneously at the two overriding optical wavebands, i.e., 1 μm and 1.55 μm, promising a remote acquisition of the sensing signals at patient by virtue of the Yb and/or Er-doped fiber amplifiers which are highly commercial. Furthermore, the functionality of the temperature-offset allows for the understanding of the biomolecular stimulating at the body temperature and thus facilitating the acceleration of the cardiac biomarker test. The proposed proof-of-concept enriches the arsenal of tools for fiber biosensors and enables a vista for the instant and in-vivo diagnosis of acute heart diseases.

Temperature self-calibrated pH sensor based on GO/PVA-coated MZI cascading FBG

A temperature self-calibrated potential of hydrogen (pH) sensor based on the single mode fiber-tapered dual core photonic crystal fiber-single mode fiber (SMF-TDCPCF-SMF) structure cascaded with a fiber Bragg grating (FBG) is proposed and demonstrated. The TDCPCF structure formed Mach-Zehnder interferometer (MZI) is modified with a coating of graphene oxide/polyvinyl alcohol (GO/PVA) hybrid hydrogel to realize the measurement of pH, and the uncoated FBG is used to calibrate temperature. In our experiment, the sensitivity coefficient of 0.69 nm/pH with R²=0.99 and the hysteresis loss of less than 0.007 are achieved within the pH range from pH 4.00 to pH 9.85. The measured response time from pH 7.00 to pH 4.00, 6.00 and 9.85 are no higher than 10s. Moreover, the resonant wavelengths of MZI and FBG also exhibit good linear relationship with the temperature sensitivity coefficient of 0.15 nm/°C (R²=0.99) and 0.09 nm/°C (R²=0.97) respectively. It is demonstrated successfully that the proposed sensor has broad application prospects in the field of environmental monitoring, biological sensing and chemical analysis, due to the good performance of the temperature self-calibrated pH monitoring, repeatability, linearity, response time and reversibility.

A Review of Corrosion in Aircraft Structures and Graphene-Based Sensors for Advanced Corrosion Monitoring

Corrosion is an ever-present phenomena of material deterioration that affects all metal structures. Timely and accurate detection of corrosion is required for structural maintenance and effective management of structural components during their life cycle. The usage of aircraft materials has been primarily driven by the need for lighter, stronger, and more robust metal alloys, rather than mitigation of corrosion. As such, the overall cost of corrosion management and aircraft downtime remains high. To illustrate, $5.67 billion or 23.6% of total sustainment costs was spent on aircraft corrosion management, as well as 14.1% of total NAD for the US Air Force aviation and missiles in the fiscal year of 2018. The ability to detect and monitor corrosion will allow for a more efficient and cost-effective corrosion management strategy, and will therefore, minimize maintenance costs and downtime, and to avoid unexpected failure associated with corrosion. Conventional and commercial efforts in corrosion detection on aircrafts have focused on visual and other field detection approaches which are time- and usage-based rather than condition-based; they are also less effective in cases where the corroded area is inaccessible (e.g., fuel tank) or hidden (rivets). The ability to target and detect specific corrosion by-products associated with the metals/metal alloys (chloride ions, fluoride ions, iron oxides, aluminum chlorides etc.), corrosion environment (pH, wetness, temperature), along with conventional approaches for physical detection of corrosion can provide early corrosion detection as well as enhanced reliability of corrosion detection. The paper summarizes the state-of-art of corrosion sensing and measurement technologies for schedule-based inspection or continuous monitoring of physical, environmental and chemical presence associated with corrosion. The challenges are reviewed with regards to current gaps of corrosion detection and the complex task of corrosion management of an aircraft, with a focused overview of the corrosion factors and corrosion forms that are pertinent to the aviation industry. A comprehensive overview of thin film sensing techniques for corrosion detection and monitoring on aircrafts are being conducted. Particular attention is paid to innovative new materials, especially graphene-derived thin film sensors which rely on their ability to be configured as a conductor, semiconductor, or a functionally sensitive layer that responds to corrosion factors. Several thin film sensors have been detailed in this review as highly suited candidates for detecting corrosion through direct sensing of corrosion by-products in conjunction with the aforementioned physical and environmental corrosion parameters. The ability to print/pattern these thin film materials directly onto specific aircraft components, or deposit them onto rigid and flexible sensor surfaces and interfaces (fibre optics, microelectrode structures) makes them highly suited for corrosion monitoring applications.

Metal-Oxide Based Nanomaterials: Synthesis, Characterization and Their Applications in Electrical and Electrochemical Sensors

Pure, mixed and doped metal oxides (MOX) have attracted great interest for the development of electrical and electrochemical sensors since they are cheaper, faster, easier to operate and capable of online analysis and real-time identification. This review focuses on highly sensitive chemoresistive type sensors based on doped-SnO₂, RhO, ZnO-Ca, Sm_x-CoFe_2−xO₄ semiconductors used to detect toxic gases (H₂, CO, NO₂) and volatile organic compounds (VOCs) (e.g., acetone, ethanol) in monitoring of gaseous markers in the breath of patients with specific pathologies and for environmental pollution control. Interesting results about the monitoring of biochemical substances as dopamine, epinephrine, serotonin and glucose have been also reported using electrochemical sensors based on hybrid MOX nanocomposite modified glassy carbon and screen-printed carbon electrodes. The fundamental sensing mechanisms and commercial limitations of the MOX-based electrical and electrochemical sensors are discussed providing research directions to bridge the existing gap between new sensing concepts and real-world analytical applications.

Biosensors for Biogenic Amines: A Review

Biogenic amines (BAs) are well-known biomolecules, mostly for their toxic and carcinogenic effects. Commonly, they are used as an indicator of quality preservation in food and beverages since their presence in higher concentrations is associated with poor quality. With respect to BA’s metabolic pathways, time plays a crucial factor in their formation. They are mainly formed by microbial decarboxylation of amino acids, which is closely related to food deterioration, therefore, making them unfit for human consumption. Pathogenic microorganisms grow in food without any noticeable change in odor, appearance, or taste, thus, they can reach toxic concentrations. The present review provides an overview of the most recent literature on BAs with special emphasis on food matrixes, including a description of the typical BA assay formats, along with its general structure, according to the biorecognition elements used (enzymes, nucleic acids, whole cells, and antibodies). The extensive and significant amount of research that has been done to the investigation of biorecognition elements, transducers, and their integration in biosensors, over the years has been reviewed.

Fiber-Optic Localized Surface Plasmon Resonance Sensors Based on Nanomaterials

Applying fiber-optics on surface plasmon resonance (SPR) sensors is aimed at practical usability over conventional SPR sensors. Recently, field localization techniques using nanostructures or nanoparticles have been investigated on optical fibers for further sensitivity enhancement and significant target selectivity. In this review article, we explored varied recent research approaches of fiber-optics based localized surface plasmon resonance (LSPR) sensors. The article contains interesting experimental results using fiber-optic LSPR sensors for three different application categories: (1) chemical reactions measurements, (2) physical properties measurements, and (3) biological events monitoring. In addition, novel techniques which can create synergy combined with fiber-optic LSPR sensors were introduced. The review article suggests fiber-optic LSPR sensors have lots of potential for measurements of varied targets with high sensitivity. Moreover, the previous results show that the sensitivity enhancements which can be applied with creative varied plasmonic nanomaterials make it possible to detect minute changes including quick chemical reactions and tiny molecular activities.

Raposo MM. Optical Fiber Sensors for Biocide Monitoring: Examples, Transduction Materials, and Prospects

Antifouling biocides are toxic to the marine environment impacting negatively on the aquatic ecosystems. These biocides, namely, tributyltin (TBT) and Cu(I) compounds, are used to avoid biofouling; however, their toxicity turns TBT and Cu(I) monitoring an important health issue. Current monitoring methods are expensive and time-consuming. This review provides an overview of the actual state of the art of antifouling paints' biocides, including their impact and toxicity, as well as the reported methods for TBT and Cu(I) detection over the past decade. The principles of optical fiber sensors (OFS) applications, with focus on environmental applications, and the use of organic chemosensors in this type of sensors are debated. The multiplexing ability of OFS and their application on aquatic environments are also discussed.

Biosensors for the Detection of Bacterial and Viral Clinical Pathogens

Biosensors are measurement devices that can sense several biomolecules, and are widely used for the detection of relevant clinical pathogens such as bacteria and viruses, showing outstanding results. Because of the latent existing risk of facing another pandemic like the one we are living through due to COVID-19, researchers are constantly looking forward to developing new technologies for diagnosis and treatment of infections caused by different bacteria and viruses. Regarding that, nanotechnology has improved biosensors' design and performance through the development of materials and nanoparticles that enhance their affinity, selectivity, and efficacy in detecting these pathogens, such as employing nanoparticles, graphene quantum dots, and electrospun nanofibers. Therefore, this work aims to present a comprehensive review that exposes how biosensors work in terms of bacterial and viral detection, and the nanotechnological features that are contributing to achieving a faster yet still efficient COVID-19 diagnosis at the point-of-care.

Microscale diamond protection for a ZnO coated fiber optic sensor

Fiber optic sensors are widely used in environmental, biological and chemical sensing. Due to the demanding environmental conditions in which they can be used, there is a risk of damaging the sensor measurement head placed in the measuring field. Sensors using nanolayers deposited upon the fiber structure are particularly vulnerable to damage. A thin film placed on the surface of the fiber end-face can be prone to mechanical damage or deteriorate due to unwanted chemical reactions with the surrounding agent. In this paper, we investigated a sensor structure formed with a Zinc Oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) on the tip of a single-mode fiber. A nanocrystalline diamond sheet (NDS) attached over the ZnO is described. The diamond structure was synthesized in a Microwave Plasma Assisted Chemical Vapor Deposition System. The deposition processes of the nanomaterials, the procedure of attaching NDS to the fiber end-face covered with ZnO, and the results of optical measurements are presented.

An Ultrasonic Tweezer With Multiple Manipulation Functions Based on the Double-Parabolic-Reflector Wave-Guided High-Power Ultrasonic Transducer

The development of ultrasonic tweezers with multiple manipulation functions is challenging. In this work, multiple advanced manipulation functions are implemented for a single-probe-type ultrasonic tweezer with the double-parabolic-reflector wave-guided high-power ultrasonic transducer (DPLUS). Due to strong high-frequency (1.49 MHz) linear vibration at the manipulation probe's tip, which is excited by the DPLUS, the ultrasonic tweezer can capture microobjects in a noncontact mode and transport them freely above the substrate. The captured microobjects that adhere to the probe's tip in the low-frequency (154.4 kHz) working mode can be released by tuning the working frequency. The results of the finite-element method analyses indicate that the manipulations are caused by the acoustic radiation force.

Label-Free Optical Resonator-Based Biosensors

The demand for biosensor technology has grown drastically over the last few decades, mainly in disease diagnosis, drug development, and environmental health and safety. Optical resonator-based biosensors have been widely exploited to achieve highly sensitive, rapid, and label-free detection of biological analytes. The advancements in microfluidic and micro/nanofabrication technologies allow them to be miniaturized and simultaneously detect various analytes in a small sample volume. By virtue of these advantages and advancements, the optical resonator-based biosensor is considered a promising platform not only for general medical diagnostics but also for point-of-care applications. This review aims to provide an overview of recent progresses in label-free optical resonator-based biosensors published mostly over the last 5 years. We categorized them into Fabry-Perot interferometer-based and whispering gallery mode-based biosensors. The principles behind each biosensor are concisely introduced, and recent progresses in configurations, materials, test setup, and light confinement methods are described. Finally, the current challenges and future research topics of the optical resonator-based biosensor are discussed.

Reflector-less nanoparticles doped optical fiber biosensor for the detection of proteins: Case thrombin

A miniature biosensing platform based on MgO-based nanoparticle doped optical fiber was developed for the biomolecule detection. The technology used a single mode fiber with MgO-based nanoparticles doped core. The detection was based on collecting the Rayleigh backscattering signatures with increased gain upon the etching of the fiber 1-2 mm away from the tip. The shift from the backscattered signal with the maximum value of the cross-correlation was used to report the results. The sensor exhibited a sensitivity range from 0.75 nm/refractive index unit up to 19.63 nm/refractive index unit for a refractive index range from 1.3329 up to 1.37649. The deposition of the thin gold layer increased the overall sensitivity of the biosensor by 3.7 times for the etched part of the fiber with diameter 8-9 μm. The proposed biosensor was tested for the detection of thrombin molecule concentrations ranging from 0.625 μg/ml to 20 μg/ml. Thiol modified DNA specific aptamers were used to functionalize the gold coated surface of the fiber for the detection. The sensor showed detectable sensitivity and specificity as compared to the other control proteins. The proposed biosensing platform could be multiplexed and can be used in vivo for the detection in clinical settings due to its miniature size, biocompatibility of silica glass and reflector less set up.