Comprehensive two-dimensional gas chromatography time of flight mass spectrometry (GC×GC-TOFMS) for environmental forensic investigations in developing countries

Performance Evaluation of an EI&CI Dual Ionization TOFMS Hyphenated with a Flow Modulated GC×GC System

The use and compatibility of a dual-ionization TOFMS operating an EI source and a CI source in parallel using a single TOF mass analyzer with flow modulated two-dimensional GC (GC×GC) is described. Important figures of merit of the mass spectrometer that are required for two-dimensional GC hyphenation such as acquisition speed, ion source response, EI/CI switching, the GC transfer, and data alignment are carefully investigated and addressed. Improved fast switching ion optics allow switching in a 100 Hz frequency between EI and CI spectra sampled from the same GC×GC effluent. The spectra quality also influenced by the preseparation, especially of the EI source, is compared to a standard setup operating a single quadrupole MS coupled to the same GC system. Further, two setups including and excluding an additional flame ionization detector are presented. High increments in CI sensitivities are achieved by utilizing the high pumping efficiencies of the CI stage of the used mass spectrometer. By leading high flow ratios of the GC×GC modulation flows toward the CI source, the intensity can be increased by factors of up to 37 while maintaining the pressure balance of the less robust EI source. Finally, thermal desorption GC×GC-EI&CI-TOFMS analyses of traffic emission samples from a federal highway in Germany are executed with the presented setup.

Survey of bioavailable PCDDs, PCDFs, dioxin-like PCBs, and PBBs in air, water, and sediment media using semipermeable membrane devices (SPMDs) deployed in the Hartbeespoort Dam area, South Africa

A survey of bioavailable polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), dioxin-like PCBs (dl-PCBs), and polybrominated biphenyls (PBBs) from ambient air, water and sediment was performed in the Hartbeespoort Dam area in South Africa, a region where data on highly toxic Stockholm Convention persistent organic pollutants (POPs) is scanty. The sampling was designed to simulate POP bioaccumulation in benthic and aquatic dwelling organisms as well as ambient air for estimation of ecological risk. The objective was to survey the spatiotemporal distribution and fate of bioavailable priority persistent organic compounds in the Hartbeespoort Dam in summer, autumn and winter seasons and to validate the utility of a comprehensive two-dimensional gas chromatography-time of flight mass spectrometry (GCxGC-TOF) method for PCDD/F, PCB, and PBB analysis. The highest detection rates for bioavailable priority POPs were for PCB 77 and PCB 126 which were detected in 15 and 16 of the 22 samples, though the majority of the detections were < LOQ for PCB 77. Overall, PCB 126, PBB 10 and PBB 49 recorded the highest quantified bioavailable concentrations per site in SPMDs deployed in the Hartbeespoort Dam. The SPMDs deployed in air at the Magalies River site in winter recorded the highest toxic equivalency quotient (TEQ) of 29.77 pg TEQ SPMD^-1. The highest TEQs recorded for SPMDs deployed in the sediment phase were 10.2, 3.3, and 3.2 pg TEQ SPMD^-1, recorded at the Harbour site in summer, Dam wall in summer and Harbour in winter respectively. In water, SPMDs deployed at the Crocodile River site recorded the highest TEQ of 0.81 pg TEQ SPMD^-1 in summer. TEQ data shows that air carries significant bioavailable dl-toxicity compared to the water phase, and sediment generally carries the highest dl-toxicity. Detection rates for bioavailable PBBs were generally very low, with < 3 detections being quantified above the LOQ for the majority of the sites. Statistical analysis of TEQs computed at all sites, using AVOVA shows that the dispersion of TEQs in the Hartbeespoort Dam is largely homogenous as the differences between the TEQs were insignificant (p > 0.05).

Analysis of multiclass organic pollutant in municipal landfill leachate by dispersive liquid-liquid microextraction and comprehensive two-dimensional gas chromatography coupled with mass spectrometry

We propose a simple, fast, and inexpensive method for the analyses of 72 organic compounds in municipal landfill leachate, based on dispersive liquid-liquid microextraction and comprehensive two-dimensional gas chromatography coupled with mass spectrometry. Forty-one organic compounds belonging to several classes including hydrocarbons, mono- and polyaromatic hydrocarbons, carbonyl compounds, terpenes, terpenoids, phenols, amines, and phthalates, covering a wide range of physicochemical properties and linked to municipal landfill leachate, were quantitatively determined. Another 31 organic compounds such as indoles, pyrroles, glycols, organophosphate flame retardants, aromatic amines and amides, pharmaceuticals, and bisphenol A have been identified based on their mass spectra. The developed method provides good performances in terms of extraction recovery (63.8-127%), intra-day and inter-day precisions (< 7.7 and < 13.9 respectively), linearity (R² between 0.9669 and 0.9999), detection limit (1.01-69.30 μg L^-1), quantification limit (1.87-138.6 μg L^-1), and enrichment factor (69.6-138.5). Detailed information on the organic pollutants contained in municipal landfill leachate could be obtained with this method during a 40-min analysis of a 4-mL leachate sample, using only 75 μL of extraction solvent.

The Blossoming of Technology for the Analysis of Complex Aroma Bouquets-A Review on Flavour and Odorant Multidimensional and Comprehensive Gas Chromatography Applications

Multidimensional approaches in gas chromatography have been established as potent tools to (almost) attain fully resolved analyses. Flavours and odours are important application fields for these techniques since they include complex matrices, and are of interest for both scientific study and to consumers. This article is a review of the main research studies in the above theme, discussing the achievements and challenges that demonstrate a maturing of analytical separation technology.

Monitoring polychlorinated dibenzo-p-dioxins/dibenzofurans and dioxin-like polychlorinated biphenyls in Africa since the implementation of the Stockholm Convention-an overview

Polychlorinated dibenzo-p-dioxin (PCDDs), polychlorinated dibenzofurans (PCDF), and dioxin-like polychlorinated biphenyl (dl-PCB) are groups of toxic compounds released into the environment as unintentional by-products of combustion. They persist, bioaccumulate through the food chain, and cause adverse health effects. This review attempts to collate available information on the release of PCDD/Fs and dl-PCBs and other critical data relevant to their monitoring in Africa during the existence of the Stockholm Convention (SC). Much as the implementation of the SC may be lagging, literature showed that there has been encouraging efforts that have been made with respect to PCDDs/Fs and dl-PCBs monitoring in Africa. Results from a global monitoring study showed that PCDD/Fs released to air in Africa stood at 18-532 fg WHO₉₈ TEQ/M³ while dl-PCBs were 7-278 fg WHO₉₈ TEQ/m³. In human milk, the total concentration of PCDD/Fs, i.e., WHO 2005 TEQ LB has been reported to range from 0.5 ng/g fat to 12 ng/g fat. Fourteen laboratories in Africa participated in inter-laboratory assessments of persistent organic pollutants (POPs) with two specifically for PCDD/Fs analysis. This shows that some efforts are being made to boost capacity in Africa. Levels of PCDDs/Fs and dl-PCBs in clay consumed by pregnant women have been reported in Cameroon, Democratic Republic of Congo (DRC), Nigeria, Zimbabwe, Ĉote d'Ivoire, and Uganda with a maximum concentration of 103 pg TEQ/g. This finding was very significant since women are the most impacted through exposure to POPs, a fact that is acknowledged by the SC.

Selective and comprehensive analysis of organohalogen compounds by GC × GC-HRTofMS and MS/MS

Thousands of organohalogen compounds, including hazardous chemicals such as polychlorinated biphenyls (PCBs) and other persistent organic pollutants (POPs), were selectively and simultaneously detected and identified with simple, or no, purification from environmental sample extracts by using several advanced methods. The methods used were software extraction from two-dimensional gas chromatography-high-resolution time-of-flight mass spectrometry (GC × GC-HRTofMS) data, measurement by negative chemical ionization with HRTofMS, and neutral loss scanning (NLS) with GC × GC-MS/MS. Global and selective detection of organochlorines and bromines in environmental samples such as sediments and fly ash was achieved by NLS using GC × GC-MS/MS (QQQ), with the expected losses of ³⁵Cl and ⁷⁹Br. We confirmed that negative chemical ionization was effective for sensitive and selective ionization of organohalogens, even using GC × GC-HRTofMS. The 2D total ion chromatograms obtained by using negative chemical ionization and selective extraction of organohalogens using original software from data measured by electron impact ionization were very similar; the software thus functioned well to extract organohalogens. Combining measurements made by using these different methods will help to detect organohalogens selectively and globally. However, to compare the data obtained by individual measurements, the retention times of the peaks on the 2D chromatograms need to match.

Origin, Analytical Characterization, and Use of Human Odor in Forensics

Developing a strategy to characterize the odor prints of individuals should be relevant to support identification obtained using dogs in courts of justice. This article proposes an overview of the techniques used for the forensic profiling of human odor. After reviewing the origin of human odor-both genetic and physiological-the different analytical steps from sample collection to statistical data processing are presented. The first challenge is the collection of odor, whether by direct sampling with polymer patches, cotton gauze, etc., or indirect sampling with devices like Scent Transfer Unit. Then, analytical techniques are presented. Analyses are commonly performed with gas chromatography coupled with mass spectrometry. As they yield large amounts of data, advanced statistical tools are needed to provide efficient and reliable data processing, which is essential to give more probative value to information.

Qualitative analysis of halogenated organic contaminants in American eel by gas chromatography/time-of-flight mass spectrometry

Target compound analysis with scanning mass spectrometers such as quadrupole or magnetic sector instruments is used extensively in environmental chemistry because of the selectivity, sensitivity, and robustness. Yet, target compound analysis selectively ignores the majority of compounds present in a sample, especially in complex matrices like fish. In this study, time-of-flight mass spectrometry was used to screen for and identify halogenated compounds in American eels (Anguilla rostrata). Individual and then pooled eel samples were analysed using electron ionization and electron capture negative ionization (ECNI) modes. Eels were differentiated by principal component analysis of chemical profiles and were grouped corresponding to their capture location, all with a single instrument injection per sample. Bromine containing compounds were further investigated by taking advantage of the selectivity of ECNI by utilizing the Br(-) ion m/z 79 and 81. A total of 51 brominated compounds were detected and their identities were attempted by authentic standards, library searching, and/or chemical formula prediction based on accurate mass measurements. Several PBDEs were identified in the samples, and the majority of the non-PBDEs identified were bromophenols, bromoanisoles, and bromobenzenes. These classes of compounds are synthesized for use in flame retardant production either as intermediates or as final products. However, their occurrence in eels was most likely the result of metabolism or break-down products of high production volume flame retardants like polybrominated diphenyl ethers and bromophenoxy compounds.

Identification of potential novel bioaccumulative and persistent chemicals in sediments from Ontario (Canada) using scripting approaches with GC×GC-TOF MS analysis

This work describes a single and fast approach using a filtering script as a means of prioritizing sample processing of data acquired by GC×GC-TOF MS for the identification of potentially novel persistent and bioaccumulative halogenated chemicals. The proposed script is based on the recognition of a generic halogenated isotope cluster pattern that allows for the simultaneous detection of chlorinated, brominated, or mixed halogen-substituted compounds in a single classification. Once developed, the script was applied to the identification of organohalogens in stream sediments collected across the southern region of Ontario (Canada). Classified peaks were first compared with available analytical standards and reference libraries to confirm the known chemicals. Unknown potential persistent organic pollutants (POPs) were evaluated for occurrence within the samples and high resolution mass spectrometry was used in order to identify some of the most prevalent compounds in the samples and resulting in the identification of three decachlorinated dechlorane analogs (C18H14Cl10), two undecachlorinated dechlorane species (C18H13Cl11), and a novel mixed chloro/bromo-carbazole (C12H5NCl2Br2) in a number of sediments analyzed. Relative peak abundances of these unknown halogenated compounds were in the same order of magnitude or slightly higher than levels observed for conventional POPs detected in the samples.

Dioxin, furan and PCB serum levels in a South African Tswana population: comparing the polluting effects of using different cooking and heating fuels

In South Africa, 26-50% of households use solid fuel for cooking food and heating houses. When used as fuel, wood and chlorinated waste are known sources of polychlorinated dibenzo-para-dioxins, polychlorinated dibenzofurans (PCDD/Fs), and polychlorinated biphenyls (PCBs). Here, we compare PCDD/F, dioxin-like PCB (DL-PCB), and non-DL-PCB (NDL-PCB) levels in serum of 693 Tswana individuals in the North West province, who either burn solid biofuels or have access to electricity, gas, and paraffin. This is the first South African study on dioxin levels in humans with more than 100 participants. Serum was pooled according to fuel use, as well as to confounding factors such as gender and age. Solid-phase extraction was used to remove the target analytes from serum, after which the extracts were further refined automatically using a combination of multilayer sorbents. Compound concentrations were determined by high-resolution mass spectrometry after high-resolution gas chromatography. Mean serum lipid content was determined enzymatically to be 5.91 ± 0.42 g/L. The PCDD/F and DL-PCB levels were similar to global concentrations reported for non-exposed adults. The mean of the total Toxic Equivalencies (ΣTEQ) was 6.9 ± 3.3 pg/g lipid and the mean NDL-PCB was 70.1 ± 42.8 ng/g lipid. The mean concentrations of the PCDDs, PCDFs and the corresponding World Health Organization-TEQ (WHO-TEQ) of the population using electricity, gas, and paraffin were greater than of those reliant on solid biomass (p = 0), whereas the DL-PCBs, their corresponding WHO-TEQ, and NDL-PCBs were greater for the population who use biofuels but not significantly so. The females had higher serum levels of the PCDDs (p = 0) and PCDFs (not significant) whereas the PCBs were higher for the males (p = 0). Breastfeeding women presented lower levels of all compound classes than their non-breastfeeding counterparts (p=0) and older subjects manifested greater pollutant loads than the younger generation (p = 0). For our study population, being regularly exposed to the combustion of solid biofuels caused higher serum levels of DL-PCBs and NDL-PCBs but not of PCDDs and PCDFs.

Environmental mass spectrometry

Environmental mass spectrometry is an important branch of science because it provides many of the data that underlie policy decisions that can directly influence the health of people and ecosystems. Environmental mass spectrometry is currently undergoing rapid development. Among the most relevant directions are a significant broadening of the lists of formally targeted compounds; a parallel interest in nontarget chemicals; an increase in the reliability of analyses involving accurate mass measurements, tandem mass spectrometry, and isotopically labeled standards; and a shift toward faster high-throughput analysis, with minimal sample preparation, involving various approaches, including ambient ionization techniques and miniature instruments. A real revolution in analytical chemistry could be triggered with the appearance of robust, simple, and sensitive portable mass spectrometers that can utilize ambient ionization techniques. If the cost of such instruments is reduced to a reasonable level, mass spectrometers could become valuable household devices.

Peptides Trapping Dioxins: A Docking-Based Inverse Screening Approach

A rapid and cost-effective computational methodology for designing and rationalizing the selection of small peptides as receptors for dioxin-like compounds was proposed. The backbone of the dioxin Ah receptor binding site was used to design a series of penta- and hexapeptide libraries, with 1400 elements in total. Peptide flexibility was considered and 10 conformers were found to be a good option to represent peptide conformational space with fair speed-accuracy ratio. Each peptide conformer was treated as a possible receptor, generating a dedicated box and then running a docking process using as ligands a family of 76 dibenzo-p-dioxins and 113 dibenzofurans mono- and polychlorinated. Significant predictions were confirmed by comparing primary structure of top and bottom ranked peptides binding dioxins confirming that scrambled positions of the same amino acids gave completely different predicted binding. The hexapeptide EWFQPW, with the best binding score, was chosen as selective sorbent material in solid-phase extraction. The retention performances were tested using the 2,3,7,8-tetrachlorodibenzo-p-dioxin and two polychlorinated biphenyls in order to verify the hexapeptide specificity. The solid-phase extraction experimental procedure was optimized, and analytical parameters of hexapeptide sorbent material were compared with the resin without hexapeptide and a commercial reversed phase cartridge.