Impact of chitosan and polyacrylamide on formation of carbonaceous and nitrogenous disinfection by-products

Novel Conductive and Redox-Active Molecularly Imprinted Polymer for Direct Quantification of Perfluorooctanoic Acid

This study developed a novel molecularly imprinted polymer (MIP) that is both conductive and redox-active for directly quantifying perfluorooctanoic acid (PFOA) electrochemically. We synthesized the monomer 3,4-ethylenedioxythiophene-2,2,6,6-tetramethylpiperidinyloxy (EDOT-TEMPO) for electropolymerization on a glassy carbon electrode using PFOA as a template, which was abbreviated as PEDOT-TEMPO-MIP. The redox-active MIP eliminated the need for external redox probes. When exposed to PFOA, both anodic and cathodic peaks of MIP showed a decreased current density. This observation can be explained by the formation of a charge-assisted hydrogen bond between the anionic PFOA and MIP's redox-active moieties (TEMPO) that hinder the conversion between the oxidized and reduced forms of TEMPO. The extent of the current density decrease showed excellent linearity with PFOA concentrations, with a method detection limit of 0.28 ng·L-1. PEDOT-TEMPO-MIP also exhibited high selectivity toward PFOA against other per- and polyfluoroalkyl substances (PFAS) at environmentally relevant concentrations. Our results suggest electropolymerization of MIPs was highly reproducible, with a relative standard deviation of 5.1% among three separate MIP electrodes. PEDOT-TEMPO-MIP can also be repeatedly used with good stability and reproducibility for PFOA detection. This study provides an innovative platform for rapid PFAS quantification using redox-active MIPs, laying the groundwork for developing compact PFAS sensors.

N-nitrosamines in electroplating and printing/dyeing industrial wastewater treatment plants: Removal efficiency, environmental emission, and the influence on drinking water

The discharge of industrial wastewater containing high concentrations of N-nitrosamines to the aquatic environment can impair downstream source waters and pose potential risks to human health. However, the transport and fate of N-nitrosamines in typical industrial wastewater treatment plants (IWWTPs) and the influence of these effluents on source water and drinking water are still unclear. This study investigated nine N-nitrosamines in four full-scale electroplating (E-) and printing/dyeing (PD-) IWWTPs, two drinking water treatment plants (DWTPs) in the lower reaches of these IWWTPs, and the corresponding tap water in South China. The total concentrations of N-nitrosamines (∑NAs) were 382-10,600, 480-1920, 494-789, and 27.9-427 ng/L in influents, effluents, source water, and tap water, respectively. The compositions of N-nitrosamine species in different influents varied a lot, while N-nitrosodi-n-butylamine (NDBA) and N-nitrosodimethylamine (NDMA) dominated in most of the effluents, source water, and tap water. More than 70 % N-nitrosamines were removed by wastewater treatment processes used in E-IWWTPs such as ferric-carbon micro-electrolysis (Fe/C-ME), while only about 50 % of N-nitrosamines were removed in PD-IWWTPs due to the use of chlorine reagent or other inefficient conventional processes such as flocculation by cationic amine-based polymers or bio-contact oxidation. Therefore, the mass fluxes of N-nitrosamines discharged from these industrial wastewaters to the environment in the selected two industrial towns were up to 14,700 mg/day. The results based on correlation and principal component analysis significantly demonstrated correlations between E-and PD-effluents and source water and tap water, suggesting that these effluents can serve as sources of N-nitrosamines to local drinking water systems. This study suggests that N-nitrosamines are prevalent in typical IWWTPs, which may infect drinking water systems. The findings of this study provide a basis data for the scientific evaluation of environmental processes of N-nitrosamines.

Assess the formation of disinfection by-products from pyrogenic dissolved organic matter (pyDOM): impact of wildfire on the water quality of forest watershed

Wildfires can release pyrogenic dissolved organic matter (pyDOM) into the forest watershed, which may pose challenges for water treatment operations downstream due to the formation of disinfection by-products (DBPs). In this study, we systematically assessed the physio-chemical properties of pyDOM (e.g., electron-donating and -accepting capacities; EDC and EAC) and their contributions to DBP formation under different disinfection scenarios using (1) ten lab samples produced from various feedstocks and pyrolysis temperatures, and (2) pre- and post-fire field samples with different burning severities. A comprehensive suite of DBPs-four trihalomethanes (THMs), nine haloacetic acids (HAAs), and seven N-nitrosamines-were included. The formations of THM and HAA showed an up to 5.7- and 8.9-fold decrease as the pyrolysis temperature increased, while the formation of N-nitrosamines exhibited an up to 6.6-fold increase for the laboratory-derived pyDOM. These results were supported by field pyDOM samples, where the post-fire samples consistently showed a higher level of N-nitrosamine formation (i.e., up to 5.3-fold), but lower THMs and HAAs compared to the pre-fire samples. To mimic environmental reducing conditions, two field samples were further reduced electrochemically and compared with Suwannee River natural organic matter (SRNOM) to evaluate their DBP formation. We found increased DBP formation in pyDOM samples following electrochemical reduction but not for SRNOM, which showed increased N-nitrosamines but decreased THMs and HAAs post-electrochemical reduction. Furthermore, this study reported for the first time the formation of two previously overlooked N-nitrosamines (i.e., nitrosodiethylamine (NDEA), N-nitrosodi-n-propylamine (NDPA)) in both laboratory and field pyDOM samples, raising concerns for drinking water safety given their higher toxicity as compared to the regulated counterparts. Results from this study provide new insights for DBP mitigation during post-fire recovery, which are particularly relevant to communities that rely on forest watersheds as their drinking water sources.

Doped and immobilized titanium dioxide photocatalysts as a potential source of nitrosamine formation

Immobilized and visible-light-active titanium dioxide (TiO₂) is widely used for water treatment. However, the accelerated generation of degradation byproducts is a potential risk of TiO₂-based photocatalysis. This study aimed to investigate the structural effect of engineered TiO₂ samples on the formation of major nitrosamines during photocatalysis. The nitrogen-containing impurities and leached metal ions from doped-TiO₂ samples could exacerbate nitrosamine formation potential (FP) in distilled water, secondary effluent, and chloraminated water. Doped-TiO₂ with 2-ethylimidazole, trimethylamine, triethylamine, and N-carbon nanotubes could leach in the range of 47-64 ng L^-1 nitrosamines (including N-nitrosomethylethylamine, N-nitrosodiethylamine, N-nitrosodimethylamine, and N-nitrosopyrrolidine) even under dark conditions. Furthermore, we investigated the role of metal dopants on nitrosamine-FP during the chloramination of precursors such as dimethylamine and microcystin-LR. Metal ions such as Cu that leached from the metal-doped catalysts may catalyze the nitrosamine-FP. Therefore, pre-purification (washing) and immobilization of doped-TiO₂ samples on substrates are suggested to remove a considerable amount of nitrosamines. However, during the prolonged tryout, the selection of substrates was critical. Polymeric supports, such as polyimide and polyvinylpyrrolidone, can produce up to 85 ng L^-1 nitrosamine, whereas TiO₂ immobilized onto steel mesh can remove nitrosamine formation during photocatalytic oxidation followed by chloramination. This study systematically screened a diverse range of dopants, supports, and solvents in engineered TiO₂ photocatalysts, in 61 samples, and provided novel insights into their effect on nitrosamine formation.

Development of multi-residue gas chromatography coupled with mass spectrometry methodologies for the measurement of 15 chemically different disinfection by-products (DBPs) of emerging concern in drinking water from two different Portuguese water treatment plants

In water treatment plants (WTPs), chemical agents, such as chlorine and ozone, might react with organic matter and anthropogenic contaminants, forming a high diversity of disinfection by-products (DBPs). Due to the potential toxicological effects, the identification of unregulated DBPs (UR-DBPs) is critical to help water managers in the selection of effective water treatment processes, contributing to improving water safety plans. Given the limited validated analytical methods to detect UR-DBPs, here we developed new multi-residue gas chromatography coupled with mass spectrometry methodologies for the detection and quantification of 15 UR-DBPs, including aldehydes, haloketones (HKs), nitrosamines and alcohols, in drinking water matrices. Solid-phase extraction (SPE), for the nitrosamine group, and solid-phase micro extraction (SPME), for the remaining DBPs, were used as sample preparation methods. The developed methodologies allowed the quantification of target UR-DBPs at trace concentration levels (ng L^-1), with method quantification limits (MQLs) ranging from 14.4 ng L^-1 to 26.0 ng L^-1 (SPE-GC-MS) and 2.3 ng L^-1 and 1596 ng L^-1 (SPME-GC-MS). The methods were applied to different drinking water matrices, considering distinct delivery points of EPAL - Empresa Portuguesa das Águas Livres WTPs. Overall, the aldehyde group, represented by decanal, nonanal and 2-ethylheaxanal, showed the highest occurrence, followed by HKs and nitrosamines. The results of this study suggested that the formation of these UR-DBPs should be further monitored in WTPs.

Evaluation of the efficiency of some disinfectants on the viability of Hymenolepis nana eggs isolated from wastewater and faecal sludge in Yaounde (Cameroon): importance of some abiotic variables

Hymenolepis nana is responsible for many parasitic infections in tropical areas, with its persistence in aquatic environments as major contributory factor. A study aimed at demonstrating the effectiveness of some disinfectants on the viability of Hymenolepis nana eggs was conducted in microcosm. Sampling consisted of taking wastewater and sewage sludge samples in sterilized containers and then transporting to the laboratory of Hydrobiology and Environmental Sciences for the determination of Hymenolepis nana eggs using standard protocols. The experimental set-up consisted of five replicates, four tests and a control. The test samples were successively treated with four disinfectants (calcium chlorite, hydrogen peroxide, gypsum and sodium hypochlorite). The physico-chemical parameters were measured before and after disinfection. The samples were then observed under an optical microscope after concentration of the sample through sedimentation and McMaster technique. The viability of the eggs was determined using incubation and staining techniques. The analysis revealed that the selected disinfectants significantly reduced the physico-chemical parameters (with an average yield ranging from 79.24 ± 19.43% to 99.24 ± 1.47%). These physico-chemical parameters can significantly influence the treatment of Hymenolepis nana eggs either by absorbing the disinfectant or by constituting a protective barrier for the eggs, and the physico-chemical nature of the disinfectant strongly influences the formation of disinfection by-products. Calcium chlorite showed a greater effectiveness in reducing egg viability with efficiency rates of 93.12 ± 9.12% followed by hydrogen peroxide (89.57 ± 14.55%), sodium hypochlorite (82.51 ± 14.39%) and gypsum (80.85 ± 12.88%). The results obtained with gypsum are almost similar to those obtained with other disinfectants (calcium chlorite, hydrogen peroxide and sodium hypochlorite) and clearly show that this disinfectant can be used in water treatment because, unlike other chemical disinfectants, it has no known toxic effects.

Enhanced coagulation for mitigation of disinfection by-product precursors: A review

The unintended formation of disinfection by-products (DBPs) has received considerable attention as it may pose risks to human health. Coagulation is the most common process for removing particulates as well as dissolved organic matter (DOM) (i.e., DBP precursors) during drinking water and wastewater treatments. With the improvement of water quality standards and the increased fluctuation in source water quality, conventional coagulation becomes challenging. Thus, significant efforts have been made to enhance coagulation to promote the removal of DOM in source water and mitigate the formation of DBPs in drinking water. This review provides a brief summary of the properties of DBP precursors and summarizes the effectiveness of enhanced coagulation involving three types of coagulants (metal-based coagulants, organic polymers, and organic-inorganic hybrid coagulants) in controlling the formation of DBPs during chlor(am)ination disinfection. Metal-based coagulants can achieve a reduction in DBP formation potential of approximately 20%-60% in natural water under enhanced coagulation conditions. Both the organic polymers (used as coagulant aids) and novel hybrid coagulants increase the removal of DOM and exhibit high potential for mitigating DBP formation. In addition, integrated treatments combining coagulation with other treatment processes (e.g., oxidation, membrane filtration, ion exchange, and adsorption) to enhance DBP precursor removal are evaluated in terms of performance, mechanisms, and features. Advanced treatments, such as membrane filtration and activated carbon adsorption, are effective coagulation-assisted processes, and can further control chlorinated DBPs; however, the elevated formation of bromate or highly brominated DBPs is of particular concern.

Nitrogen-Free Cationic Starch Flocculants: Flocculation Performance, Antibacterial Ability, and UF Membrane Fouling Control

In light of growing concerns about the formation of nitrogen-based disinfection byproducts (N-DBP) and the possible contribution from the use of quaternary-ammonium-containing flocculants, there is growing interest in the alternative use of quaternary phosphonium salts, which have been reported to have a lower DBP formation potential, stronger cationic properties, lower cytotoxicity, and greater stability. In this study, the performance of N-free quaternary-phosphonium-modified starch flocculants (S-BTP), synthesized through a facile one-step method using commercially available raw materials, in the treatment of bacteria-laden waters (E. coli as the model bacteria) was assessed in both jar tests and a bench-scale continuous-flow flocculation-sedimentation-ultrafiltration process. In jar tests, the effects of the cationic degree of substitution (DS) and dosage of the flocculant, solution pH, and presence of model contaminants on treatment performance were studied. One particular flocculant (S-BTP3), with a DS of 19.3%, displayed high removal efficiencies of E. coli, turbidity, and UV₂₅₄ from water, comparable with those of ammonium-based analogues and conventional alum, via a combination of charge attraction, polymer bridging, and antibacterial effects. S-BTP3 also possessed better bactericidal properties (99.4% of E. coli killed) than alum (41.4% killed) and did not cause the release of intracellular substances into the treated water. In the continuous-flow flocculation-sedimentation-UF tests, S-BTP3 was superior to alum in the flocculation and antibacterial performance, and in mitigating UF membrane fouling. The results have clearly demonstrated the multiple benefits of the use of N-free cationic starch flocculants in water treatment as an alternative to conventional chemicals.

GAC to BAC: Does it make chloraminated drinking water safer?

Biological activated carbon (BAC) is widely used as a polishing step at full-scale drinking water plants to remove taste and odor compounds and assimilable organic carbon. BAC, especially with pre-ozonation, has been previously studied to control regulated disinfection by-products (DBPs) and DBP precursors. However, most previous studies only include regulated or a limited number of unregulated DBPs. This study explored two full-scale drinking water plants that use pre-chloramination followed by BAC and chloramine as the final disinfectant. While chloramine generally produces lower concentrations of regulated DBPs, it may form increased levels of unregulated nitrogenous and iodinated DBPs. We evaluated 71 DBPs from ten DBP classes including haloacetonitriles, haloacetamides, halonitromethanes, haloacetaldehydes, haloketones, iodinated acetic acids, iodinated trihalomethanes, nitrosamines, trihalomethanes, and haloacetic acids, along with speciated total organic halogen (total organic chlorine, bromine and iodine) across six different BAC filters of increasing age. Most preformed DBPs were well removed by BAC with different ages (i.e., operation times). However, some preformed DBPs were poorly removed or increased following treatment with BAC, including chloroacetaldehyde, dichloronitromethane, bromodichloronitromethane, N-nitrosodimethylamine, dibromochloromethane, tribromomethane, dibromochloroacetic acid, and tribromoacetic acid. Some compounds, including dibromoacetaldehyde, bromochloroacetamide, and dibromoacetamide, were formed only after treatment with BAC. Total organic halogen removal was variable in both plants and increases in TOCl or TOI were observable on one occasion at each plant. While calculated genotoxicity decreased in all filters, decreases in overall DBP formation did not correlate with decreases in calculated cytotoxicity. In three of the six filters, calculated toxicity increased by 4-27%. These results highlight that DBP concentration alone may not always provide an adequate basis for risk assessment.

Disinfection byproduct formation during drinking water treatment and distribution: A review of unintended effects of engineering agents and materials

Unintended effects of engineering agents and materials on the formation of undesirable disinfection byproducts (DBPs) during drinking water treatment and distribution were comprehensively reviewed. Specially, coagulants, biologically active filtration biofilms, activated carbons, nanomaterials, ion-exchange resins, membrane materials in drinking water treatment and piping materials, deposits and biofilms within drinking water distribution systems were discussed, which may serve as DBP precursors, transform DBPs into more toxic species, and/or catalyze the formation of DBPs. Speciation and quantity of DBPs generated rely heavily on the material characteristics, solution chemistry conditions, and operating factors. For example, quaternary ammonium polymer coagulants can increase concentrations of N-nitrosodimethylamine (NDMA) to above the California notification level (10 ng/L). Meanwhile, the application of strong base ion-exchange resins has been associated with the formation of N-nitrosamines and trichloronitromethane up to concentrations of 400 ng/L and 9.0 μg/L, respectively. Organic compounds leaching from membranes and plastic and rubber pipes can generate high NDMA (180-450 ng/L) and chloral hydrate (∼12.4 μg/L) upon downstream disinfection. Activated carbon and membranes preferentially remove organic precursors over bromide, resulting in a higher proportion of brominated DBPs. Copper corrosion products (CCPs) accelerate the decay of disinfectants and increase the formation of halogenated DBPs. Chlorination of high bromide waters containing CCPs can form bromate at concentrations exceeding regulatory limits. Owing to the aforementioned concern for the drinking water quality, the application of these materials and reagents during drinking water treatment and distribution should be based on the removal of pollutants with consideration for balancing DBP formation during disinfection scenarios. Overall, this review highlights situations in which the use of engineering agents and materials in drinking water treatment and distribution needs balance against deleterious impacts on DBP formation.

Formation potential of nine nitrosamines from polyacrylamide during chloramination

Cationic polymers, which are commonly used as flocculants and coagulant aids in water and wastewater treatment, have been recently reported to promote the formation of nitrosamines. Most of the findings to date are based on poly (epichlorohydrin dimethylamine) and poly (diallyldimethylammonium chloride), while few studies have considered nitrosamines formation of polyacrylamides. In this work, the nitrosamines formation from non-ionic, anionic and cationic polyacrylamides was evaluated. Moreover, the effects of chemical structures of cationic polyacrylamides (including molecular weight, charge density, and monomers) on nitrosamines formation were investigated. The results revealed that the highest amount of nitrosamines formation was formed from cationic polyacrylamide, followed by non-ionic polyacrylamide and anionic polyacrylamide. Molecular weight and various cationic monomers showed no significant effects on nitrosamines formation, but monomers generated significantly higher amount of nitrosamines formation than cationic polyacrylamides. Nitrosamines formation increased with the increasing charge density of cationic polyacrylamides, and FTIR analysis results showed that the quaternary amine groups preferentially reacted with chloramines than with amide groups. This work shed new light on the nitrosamines formation from water and wastewater treatment polymers.