Effective swine wastewater treatment by combining microbial fuel cells with flocculation

Organic stabilization and methane production under different organic loading rates in UASB treating swine wastewater

This study proposes the was to evaluate the stability and methane production with organic load differents in an upflow anaerobic sludge blanket reactor (UASB) treating swine wastewater by methods of multivariate analysis. Four organic loads were used with average hydraulic holding times of one day. The methods of data analysis of linear regression, Pearson correlation, principal component analysis and hierarchical clustering analysis were used for understanding stability and methane production in the reactor. The highest concentrations of bicarbonate alkalinity of 683 mg L-1 CaCO3 and total volatile acids of 1418 mg L-1 HAc with maximum organic loading applied were obtained. The optimal stability conditions occurred at an intermediate and partial alkalinity ratio between 0.24 and 0.25 observed in initial phases with a chemical oxygen demand (COD) removal of 47-57%. Maximum methane production was 9.0 L CH4 d-1 observed with linear regression positive and occurred at the highest applied organic load, corresponding to the highest COD removal efficiency and increased microbial biomass. Positive and negative correlation between functional stability in anaerobic digestion showed regular activity between acids, alkalinity and organic matter removal. This fact was also proven by the analysis of principal components that showed three components responsible for explaining 83.2% of the data variability, and the alkalinity, organic matter influent and organic acids had the greatest effects on the stability of the UASB reactor. Hierarchical clusters detected the formation of five groupings with a similarity of 50.1%, indicating that temperature and pH were variables with unitary influences on data dimensionality.

Recent advances in swine wastewater treatment technologies for resource recovery: A comprehensive review

Swine wastewater (SW), characterized by highly complex organic and nutrient substances, poses serious impacts on aquatic environment and public health. Furthermore, SW harbors valuable resources that possess substantial economic potential. As such, SW treatment technologies place increased emphasis on resource recycling, while progressively advancing towards energy saving, sustainability, and circular economy principles. This review comprehensively encapsulates the state-of-the-art knowledge for treating SW, including conventional (i.e., constructed wetlands, air stripping and aerobic system) and resource-utilization-based (i.e., anaerobic digestion, membrane separation, anaerobic ammonium oxidation, microbial fuel cells, and microalgal-based system) technologies. Furthermore, this research also elaborates the key factors influencing the SW treatment performance, such as pH, temperature, dissolved oxygen, hydraulic retention time and organic loading rate. The potentials for reutilizing energy, biomass and digestate produced during the SW treatment processes are also summarized. Moreover, the obstacles associated with full-scale implementation, long-term treatment, energy-efficient design, and nutrient recovery of various resource-utilization-based SW treatment technologies are emphasized. In addition, future research prospective, such as prioritization of process optimization, in-depth exploration of microbial mechanisms, enhancement of energy conversion efficiency, and integration of diverse technologies, are highlighted to expand engineering applications and establish a sustainable SW treatment system.

Multi-anode enhanced the bioelectricity generation in air-cathode microbial fuel cells towards energy self-sustaining wastewater treatment

Microbial fuel cells (MFCs) hold considerable promise for harnessing the substantial energy resources present in wastewater. However, their practical application in wastewater treatment is limited by inadequate removal of organic matter and inefficient power recovery. Previous studies have investigated aeration as a method to enhance the removal of organic matter, but this method is energy-intensive. To address this issue, this study proposed using MFC-recovered bioelectricity for aeration, thereby mitigating the associated expenses. An air-cathode MFC with multi-anode was constructed and optimized to maximize electricity supply for aeration. Carbon-felt anodes were chosen as the most effective anode configuration, due to the high abundance of electroactive bacteria and genes observed in the biofilm generated on their surface. By incorporating six carbon felt anodes, the MFC achieved a 1.7 and 1.1 fold enhancement in the maximum power and current density, respectively. The optimized MFC unit achieved a stable current density of 0.32 A/m2 and achieved COD removal of 60% in the long-term operation of 140 days in a 50 L reactor. In a reactor scaled up to 1600 L, 72 MFCs successfully powered a mini air pump work for 10 s after an 81-s charging period. The intermittent aeration resulted in partial increases in DO concentrations to 0.03-3.5 mg/L, which is expected to promote the removal of nitrogen compounds by the nitrification-anammox process. These groundbreaking results lay the foundation for self-sustaining wastewater treatment technologies.

A review of microbial fuel cell and its diversification in the development of green energy technology

The advancement of microbial fuel cell technology is rapidly growing, with extensive research and well-established methodologies for enhancing structural performance. This terminology attracts researchers to compare the MFC devices on a technological basis. The architectural and scientific successes of MFCs are only possible with the knowledge of engineering and technical fields. This involves the structure of MFCs, using substrates and architectural backbones regarding electrode advancement, separators and system parameter measures. Knowing about the MFCs facilitates the systematic knowledge of engineering and scientific principles. The current situation of rapid urbanization and industrial growth is demanding the augmented engineering goods and production which results in unsolicited burden on traditional wastewater treatment plants. Consequently, posing health hazards and disturbing aquatic veracity due to partial and untreated wastewater. Therefore, it's sensible to evaluate the performance of MFCs as an unconventional treatment method over conventional one to treat the wastewater. However, MFCs some benefits like power generation, stumpy carbon emission and wastewater treatment are the main reasons behind the implementation. Nonetheless, few challenges like low power generation, scaling up are still the major areas needs to be focused so as to make MFCs sustainable one. We have focused on few archetypes which majorities have been laboratory scale in operations. To ensure the efficiency MFCs are needed to integrate and compatible with conventional wastewater treatment schemes. This review intended to explore the diversification in architecture of MFCs, exploration of MFCs ingredients and to provide the foreseen platform for the researchers in one source, so as to establish the channel for scaling up the technology. Further, the present review show that the MFC with different polymer membranes and cathode and anode modification presents significant role for potential commercial applications after change the system form prototype to pilot scale.

Energy generation from bioelectrochemical techniques: Concepts, reactor configurations and modeling approaches

The process industries play a significant role in boosting the economy of any nation. However, poor management in several industries has been posing worrisome threats to an environment that was previously immaculate. As a result, the untreated waste and wastewater discarded by many industries contain abundant organic matter and other toxic chemicals. It is more likely that they disrupt the proper functioning of the water bodies by perturbing the sustenance of many species of flora and fauna occupying the different trophic levels. The simultaneous threats to human health and the environment, as well as the global energy problem, have encouraged a number of nations to work on the development of renewable energy sources. Hence, bioelectrochemical systems (BESs) have attracted the attention of several stakeholders throughout the world on many counts. The bioelectricity generated from BESs has been recognized as a clean fuel. Besides, this technology has advantages such as the direct conversion of substrate to electricity, and efficient operation at ambient and even low temperatures. An overview of the BESs, its important operating parameters, bioremediation of industrial waste and wastewaters, biodegradation kinetics, and artificial neural network (ANN) modeling to describe substrate removal/elimination and energy production of the BESs are discussed. When considering the potential for use in the industrial sector, certain technical issues of BES design and the principal microorganisms/biocatalysts involved in the degradation of waste are also highlighted in this review.

The potential and sustainable strategy for swine wastewater treatment: Resource recovery

Swine wastewater is highly polluted with complex and harmful substances that require effective treatment to minimize environmental damage. There are three commonly used biological technologies for treating swine wastewater: conventional biological technology (CBT), microbial electrochemical technology (MET), and microalgae technology (MT). However, there is a lack of comparison among these technologies and a lack of understanding of their unique advantages and efficient operation strategies. This review aims to compare and contrast the characteristics, influencing factors, improvement methods, and microbial mechanisms of each technology. CBT is cost-effective but has low resource recovery efficiency, while MET and MT have the highest potential for resource recovery. However, all three technologies are affected by various factors and toxic substances such as heavy metals and antibiotics. Improved methods include exogenous/endogenous enhancement, series reactor operation, algal-bacterial symbiosis system construction, etc. Though MET is limited by construction costs, CBT and MT have practical applications. While swine wastewater treatment processes have developed automatic control systems, the application need further promotion. Furthermore, key functional microorganisms involved in CBT's pollutant removal or transformation have been detected, as have related genes. The unique electroactive microbial cooperation mode and symbiotic mode of MET and MT were also revealed, respectively. Importantly, the future research should focus on broadening the scope and scale of engineering applications, preventing and controlling emerging pollutants, improving automated management level, focusing on microbial synergistic metabolism, enhancing resource recovery performance, and building a circular economy based on low-cost and resource utilization.

Microbe-Anode Interactions: Comparing the impact of genetic and material engineering approaches to improve the performance of microbial electrochemical systems (MES)

Microbial electrochemical systems (MESs) are a highly versatile platform technology with a particular focus on power or energy production. Often, they are used in combination with substrate conversion (e.g., wastewater treatment) and production of value-added compounds via electrode-assisted fermentation. This rapidly evolving field has seen great improvements both technically and biologically, but this interdisciplinarity sometimes hampers overseeing strategies to increase process efficiency. In this review, we first briefly summarize the terminology of the technology and outline the biological background that is essential for understanding and thus improving MES technology. Thereafter, recent research on improvements at the biofilm-electrode interface will be summarized and discussed, distinguishing between biotic and abiotic approaches. The two approaches are then compared, and resulting future directions are discussed. This mini-review therefore provides basic knowledge of MES technology and the underlying microbiology in general and reviews recent improvements at the bacteria-electrode interface.

Isolation and Characterization of Bacteria with High Electroactive Potential from Poultry Wastewater

Natural resources are in short supply, and the ecosystem is being damaged as a result of the overuse of fossil fuels. The creation of novel technology is greatly desired for investigating renewable and sustainable energy sources. Microorganisms have received a lot of interest recently for their potential to transform organic waste into sustainable energy and high-value goods. New exoelectrogens that can transmit electrons to electrodes and remove specific wastewater contaminants are expected to be studied. In this study, we examined three distinct samples (as determined by chemical oxygen demand and pH) that can be used as anolytes to generate power in single-chamber and double-chamber microbial fuel cells using graphite electrodes. Wastewater from poultry farms was studied as an exoelectrogenic anolyte for microbial fuel cell power generation. The study examined 10 different bacterial strains, numbered A1 through A10. Due to their highly anticipated capacity to metabolize organic/inorganic chemicals, the diverse range of microorganisms found in poultry wastewater inspired us to investigate the viability of generating electricity using microbial fuel cells. From the investigated bacterial strains, the highest voltage outputs were produced by strains A1 (Lysinibacillus sphaericus) and A2 (Bacillus cereus), respectively, at 402 mV and 350 mV. Among the 10 different bacterial strains, strain A6 generated the least amount of electricity, measuring 35.03 mV. Furthermore, a maximum power density of 16.16 1.02 mW/m² was achieved by the microbial fuel cell using strain A1, significantly outperforming the microbial fuel cell using a sterile medium. The strain A2 showed significant current and power densities of 35 1.12 mA/m² and 12.25 1.05 mW/m², respectively. Moreover, in the two representative strains, chemical oxygen demand removal and Coulombic efficiency were noted. Samples from the effluent anode chamber were taken in order to gauge the effectiveness of chemical oxygen demand removal. Wastewater had an initial chemical oxygen demand content of 350 mg/L on average. Strains A1 and A2 decomposed 94.28% and 91.71%, respectively, of the organic substrate, according to the chemical oxygen demand removal efficiency values after 72 h. Strains A1 and A2 had electron donor oxidation efficiencies for 72 h of 54.1% and 60.67%, respectively. The Coulombic efficiency increased as the chemical oxygen demand decreased, indicating greater microbial electroactivity. With representative strains A1 and A2, Coulombic efficiencies of 10% and 3.5%, respectively, were obtained in the microbial fuel cell. The findings of this study greatly advance the field as a viable source of power technology for alternative energy in the future, which is important given the depletion of natural resources.

Scale-up of the bioelectrochemical system: Strategic perspectives and normalization of performance indices

Electrochemists and ecological engineers find environmental bioelectrochemistry appealing; however, there is a big gap between expectations and actual progress in bioelectrochemical system (BES). Implementing such technology opens new opportunities for novel electrochemical reactions for resource recovery and effective wastewater treatment. Loopholes of BES exist in its scaling-up applications, and numerous attempts toward practical applications (200, 1000, and 1500 L) are key successive indicators toward its commercialization. This review emphasized the critical rethinking of standardization of performance indices i.e. current generation (A/m²), net energy recovery (kWh/kg·COD), product/resource yield (mM), and economic feasibility ($/kWh) to make fair comparison with the existing treatment system. Therefore, directional perspectives, including modularity, energy-cost balance, energy and resource recovery, have been proposed for the sustainable market of BES. The current state of the art and up-gradation in resource recovery and contaminant removal warrants a systematic rethinking of functional worth and niches of BES for practical applications.

Organic Waste Substrates for Bioenergy Production via Microbial Fuel Cells: A Key Point Review

High-energy consumption globally has raised questions about the low environmentally friendly and high-cost processes used until now for energy production. Microbial fuel cells (MFCs) may support alternative more economically and environmentally favorable ways of bioenergy production based on their advantage of using waste. MFCs work as bio-electrochemical devices that consume organic substrates in order for the electrogenic bacteria and/or enzyme cultures to produce electricity and simultaneously lower the environmental hazardous value of waste such as COD. The utilization of organic waste as fuels in MFCs has opened a new research path for testing a variety of by-products from several industry sectors. This review presents several organic waste substrates that can be employed as fuels in MFCs for bioenergy generation and the effect of their usage on power density, COD (chemical oxygen demand) removal, and Coulombic efficiency enhancement. Moreover, a demonstration and comparison of the different types of mixed waste regarding their efficiency for energy generation via MFCs are presented. Future perspectives for manufacturing and cost analysis plans can support scale-up processes fulfilling waste-treatment efficiency and energy-output densities.

Modifying Ti3C2 MXene with NH4+ as an excellent anode material for improving the performance of microbial fuel cells

Poor anode performance is one of the main bottlenecks in the development of microbial fuel cells (MFCs) for practical applications. Multilayered Ti₃C₂ MXene (m-MXene) is an alternative anode modification material because of its high specific surface area and electrical conductivity. However, the multilayered structure, negatively charged surface, and electropositivity of m-MXene could limit its modification effects. In this work, we used a solution-phase flocculation method (ammonium ion method) to restack and aggregate MXene nanosheets as an anode modification material (n-MXene). The n-MXene-modified anode had a higher specific surface area, surface hydrophilicity and surface electropositivity than the m-MXene-modified anode. The n-MXene-modified anode obtained a maximum current density of 2.1 A m^-2, which was 31.2% and 61.5% higher than that of the m-MXene-modified anode (1.6 A m^-2) and bare carbon fiber cloth anode (1.3 A m^-2). This improved anode performance was attributed to both the decrease in the charge transfer resistance and diffusion resistance, which were related to the increased quantity of biomass and microbial nanowire (or pili)-shaped filaments on the electrode surface. This work provides a simple and cost-effective approach to prepare MXene nanosheets for the modification of MFC anodes.

Efficiency of microbial fuel cells in the treatment and energy recovery from food wastes: Trends and applications - A review

The rising global population and their food habits result in food wastage and cause an obstacle in its treatment and disposal. Due to the rapid shift in the lifestyle of the human population and urbanization, almost one-third of the food produced is wasted from various sectors like domestic sources, agricultural sectors, and industrial sectors. These food resources squandered are rich in organic biomolecules which can cause complications upon direct disposal in the environment. Conventional disposal methods like composting, landfills and incineration demand high costs besides causing severe environmental and health issues. To overcome these demerits of the conventional methods and to avoid the loss of rich organic food resources, there is an immediate need for a sustainable and eco-friendly solution for the valorization of the food wastes. Microbial fuel cells (MFCs) are gaining attention, due to their ideal approach in the production of electricity and parallel treatment of organic food wastes. The MFCs are significant as an innovative approach using microorganisms and oxidizing the organic food wastes into bio-electricity. In this review, the recent advancements and practices of the MFCs in the field of food waste treatment and management along with electricity production are discussed. The major outcome of this work highlights the setting up of MFC for the treatment of higher volumes of food waste residues and enhancing the bioelectricity production in an optimal condition. For further improvements in the food waste treatments using MFCs, greater understanding and more research needs are to be focused on the commercialization, different operational modes, operational types, and low-cost fabrication coupled with careful examination of scale-up factors.

Bioelectrochemical system as an innovative technology for treatment of produced water from oil and gas industry: A review

Disposal of the high volume of produced water (PW) is a big challenge to the oil and gas industry. High cost of conventional treatment facilities, increasing energy prices and environmental concern had focused governments and the industry itself on more efficient treatment methods. Bioelectrochemical system (BES) has attracted the attention of researchers because it represents a sustainable way to treat wastewater. This is the first review that summarizes the progress done in PW-fed BESs with a critical analysis of the parameters that influence their performances. Inoculum, temperature, hydraulic retention time, external resistance, and the use of real or synthetic produced water were found to be deeply related to the performance of BES. Microbial fuel cells are the most analyzed BES in this field followed by different types of microbial desalination cells. High concentration of sulfates in PW suggests that most of hydrocarbons are removed mainly by using sulfates as terminal electron acceptor (TEA), but other TEAs such as nitrate or metals can also be employed. The use of real PW as feed in experiments is highly recommended because biofilms when using synthetic PW are not the same. This review is believed to be helpful in guiding the research directions on the use of BES for PW treatment, and to speed up the practical application of BES technology in oil and gas industry.

Comparative evaluation of simultaneous nitritation/denitritation and energy recovery in air-cathode microbial fuel cells (ACMFCs) treating low C/N ratio wastewater

Air-cathode microbial fuel cells (ACMFCs) can extract available electrons from the low C/N ratio wastewater (LCNW) for pollutant degradation and power generation. However, the multiple effects of operating parameters and their relationship between the performances and parameters are still lacking. In this study, several ACMFCs for simultaneous nitritation/denitritation (SND) and energy recovery were constructed and evaluated in terms of chemical oxygen demand (COD), NH₄⁺-N, C/N ratio, phosphate buffer solution (PBS), and external resistance (R_ext), and several derived parameters (e.g., organic loading rate (OLR), nitrogen loading rate (NLR)). Results indicated that ACMFCs could be used to treat LCNW successfully with high pollutant removal rates and sustainable current generation. Maximum removal efficiencies of 94% COD, 92% NH₄⁺-N, and 92% total nitrogen (TN) were achieved. A maximum power density of 1400 mW m^-2 and columbic efficiency of 69.2% were also obtained at a low C/N ratio of 1.7-2.6. Low C/N ratios promoted SND by balancing nitritation and denitritation. The microbial community and their predicated function results showed considerable nitrifiers and denitrificans were enriched in the ACMFCs, contributing to SND and power recovery. Further analyses showed that the NH₄⁺-N could inhibit SND, but PBS and R_ext had no obvious effects on this outcome. Co-occurrence network analysis demonstrated that power is positively correlated with COD and R_ext; strong correlations between organic removal and COD, and between nitrogen removal and ammonia, conductivity, and C/N ratio were also noted. Overall, the appropriate control of such parameters is necessary to achieve efficient SND in ACMFCs for LCNW treatment.

Biochemical potential evaluation and kinetic modeling of methane production from six agro-industrial wastewaters in mixed culture

Methane (CH₄) production from anaerobic digestion of solid and liquid agro-industrial wastes is an attractive strategy to meet the growing need for renewable energy sources and promote environmentally appropriate disposal of organic wastes. This work aimed at determining the CH₄ production potential of six agro-industrial wastewaters (AWW), evaluating the most promising for methanization purposes. It also aims to provide kinetic parameters and stoichiometric coefficients of CH₄ production and define which kinetic models are most suitable for simulating the CH₄ production of the evaluated substrates. The AWW studied were swine wastewater (SW), slaughterhouse wastewater (SHW), dairy wastewater (DW), brewery wastewater (BW), fruit processing wastewater (FPW), and residual glycerol (RG) of biodiesel production. RG was the substrate that showed the highest methanization potential. Exponential kinetic models can be efficiently applied for describing CH₄ production of more soluble substrates. On the other hand, logistic models were more suitable to predict the CH₄ production of more complex substrates.

Phyco-remediation of swine wastewater as a sustainable model based on circular economy

Pork production has expanded in the world in recent years. This growth has caused a significant increase in waste from this industry, especially of wastewater. Although there has been an increase in wastewater treatment, there is a lack of useful technologies for the treatment of wastewater from the pork industry. Swine farms generate high amounts of organic pollution, with large amounts of nitrogen and phosphorus with final destination into water bodies. Sadly, little attention has been devoted to animal wastes, which are currently treated in simple systems, such as stabilization ponds or just discharged to the environment without previous treatment. This uncontrolled release of swine wastewater is a major cause of eutrophication processes. Among the possible treatments, phyco-remediation seems to be a sustainable and environmentally friendly option of removing compounds from wastewater such as nitrogen, phosphorus, and some metal ions. Several studies have demonstrated the feasibility of treating swine wastewater using different microalgae species. Nevertheless, the practicability of applying this procedure at pilot-scale has not been explored before as an integrated process. This work presents an overview of the technological applications of microalgae for the treatment of wastewater from swine farms and the by-products (pigments, polysaccharides, lipids, proteins) and services of commercial interest (biodiesel, biohydrogen, bioelectricity, biogas) generated during this process. Furthermore, the environmental benefits while applying microalgae technologies are discussed.

Estimation of total energy requirement for sewage treatment by a microbial fuel cell with a one-meter air-cathode assuming Michaelis–Menten COD degradation

Calculations of chemical oxygen demand (COD) degradation in sewage by a microbial fuel cell (MFC) were used to estimate the total energy required for treatment of the sewage. Mono-exponential regression (MER) and the Michaelis–Menten equation (MME) were used to describe the MFC's COD removal rate (CRR). The tubular MFC used in this study (ϕ 5.0 × 100 cm) consisted of an air core surrounding a carbon-based cathode, an anion exchange membrane, and graphite non-woven fabric immersed in sewage. The MFC generated 0.26 A m⁻² of the electrode area and 0.32 W m⁻³ of the sewage water, and 3.9 W h m⁻³ in a chemostat reactor supplemented continuously with sewage containing 180 mg L⁻¹ of COD with a hydraulic retention time (HRT) of 12 h. The COD removal and coulombic efficiency (CE) were 46% and 19%, respectively, and the energy generation efficiency (EGE) was 0.054 kW h kg⁻¹-COD. The CRR and current in the MFC were strongly dependent on the COD, which could be controlled by varying the HRT. The MER model predicted first-order rate constants of 0.054 and 0.034 for reactors with and without MFC, respectively. The difference in these values indicated that using MFC significantly increased the COD removal. The results of fitting the experimental data to the MME suggested that the total COD can be separated into nondegradable CODs (C_n) and degradable CODs (C_d) via MFC. The values of CRR for C_d and CE suggest that MFC pretreatment for 12 hours prior to aeration results in a 75% decrease in net energy consumption while reducing sewage COD from 180 to 20 mg L⁻¹.

Calculations of chemical oxygen demand (COD) degradation in sewage by a microbial fuel cell (MFC) were used to estimate the total energy required for treatment of the sewage.

Performance evaluation of microbial fuel cell for landfill leachate treatment: Research updates and synergistic effects of hybrid systems

Over half of century, sanitary landfill was and is still the most economical treatment strategy for solid waste disposal, but the environmental risks associated with the leachate have brought attention of scientists for its proper treatment to avoid surface and ground water deterioration. Most of the treatment technologies are energy-negative and cost intensive processes, which are unable to meet current environmental regulations. There are continuous demands of alternatives concomitant with positive energy and high effluent quality. Microbial fuel cells (MFCs) were launched in the last two decades as a potential treatment technology with bioelectricity generation accompanied with simultaneous carbon and nutrient removal. This study reviews capability and mechanisms of carbon, nitrogen and phosphorous removal from landfill leachate through MFC technology, as well as summarizes and discusses the recent advances of standalone and hybrid MFCs performances in landfill leachate (LFL) treatment. Recent improvements and synergetic effect of hybrid MFC technology upon the increasing of power densities, organic and nutrient removal, and future challenges were discussed in details.

Effect of salinity and pH on dark fermentation with thermophilic bacteria pretreated swine wastewater

The utilization of swine wastewater is affected by salinity and pH owing to the extensive use with seawater instead of domestic water as swine farm flushing water in coastal city. Therefore, swine wastewater pretreated with thermophilic bacteria was used as fermentation substrate in this work, the effects of salinity and pH on dark fermentation under mesophilic condition were investigated. The research showed that 1.5% salinity and pH 6.0 were the optimal conditions for hydrogen production with swine wastewater. The activity of hydrogenogen was inhibited at 3.5% salinity and pH 5.0. Soluble organic matter in substrate was accumulated under high salinity and alkaline conditions. The utilization of carbohydrate during dark fermentation was up to 61.1% at 1.5% salinity and 51.5% at pH 9.0. Enhancing of salinity and pH had an advantage in accumulation of total soluble metabolites. Acetate was the main metabolite during dark fermentation, and 1.5% salinity contributed to the formation of butyrate.

A kinetic study on carboxylic acids production using bovine slaughterhouse wastewater: a promising substrate for resource recovery in biotechnological processes

Carboxylic acids (CA) are considered high added-value compounds, and their production from wastes has gained economic and environmental notoriety. However, the CA production and kinetic modeling using some agro-industrial wastewaters, such as bovine slaughterhouse wastewater (SHW), are not well reported in the literature. Therefore, the objective of this work was to evaluate the CA production potential using SHW as a substrate under acidogenic conditions and to apply mathematical models to estimate the kinetic parameters of particulate organic matter hydrolysis, soluble organic matter consumption, and CA production. Tests were carried out in quadruplicate batch reactors with a 250-mL reaction volume, with brewery sludge as inoculum and using chloroform (0.05%, v/v) for methanogenesis inhibition. The obtained yield was 0.55 g acids gCOD_A^-1, corresponding to 0.76 gCOD gCOD_A^-1. The production of caproic acid without the addition of electron donors was achieved. Mathematical models that describe exponential growth, such as the first-order exponential model, cone model, and Fitzhugh model, were the most suitable to describe the production kinetics of CA. Finally, SHW seems to be a promising substrate to be investigated in the carboxylic platform.

New progress of ammonia recovery during ammonia nitrogen removal from various wastewaters

The recovery of ammonia-nitrogen during wastewater treatment and water purification is increasingly critical in energy and economic development. The concentration of ammonia-nitrogen in wastewater is different depending on the type of wastewater, making it challenging to select ammonia-nitrogen recovery technology. Meanwhile, the conventional nitrogen removal method wastes ammonia-nitrogen resources. Based on the circular economy, this review comprehensively introduces the characteristics of several main ammonia-nitrogen source wastewater plants and their respective challenges in treatment, including municipal wastewater, industrial wastewater, livestock and poultry wastewater and landfill leachate. Furthermore, we introduce the main methods currently adopted in the ammonia-nitrogen removal process of wastewater from physical (air stripping, ion exchange and adsorption, membrane and capacitive deionization), chemical (chlorination, struvite precipitation, electrochemical oxidation and photocatalysis) and biological (classical and typical activated sludge, novel methods based on activated sludge, microalgae and photosynthetic bacteria) classification based on the ammonia recovery concept. We discuss the applicable methods of recovering ammonia nitrogen in several main wastewater plants. Finally, we prospect the research direction of ammonia removal and recovery in wastewater based on sustainable development.

Progress in Nitrogen Removal in Bioelectrochemical Systems

Nitrogenous compounds attract great attention because of their environmental impact and harmfulness to the health of human beings. Various biological technologies have been developed to reduce the environmental risks of nitrogenous pollutants. Bioelectrochemical systems (BESs) are considered to be a novel biological technology for removing nitrogenous contaminants by virtue of their advantages, such as low energy requirement and capacity for treating wastewaters with a low C/N ratio. Therefore, increasing attention has been given to carry out biological processes related to nitrogen removal with the aid of cathodic biofilms in BESs. Prior studies have evaluated the feasibility of conventional biological processes including nitrification, denitrification, and anaerobic ammonia oxidation (anammox), separately or combined together, to remove nitrogenous compounds with the help of BESs. The present review summarizes the progress of developments in BESs in terms of the biological process, cathodic biofilm, and affecting factors for efficient nitrogen removal.

Enhancing swine wastewater hydrolysis with thermophilic bacteria and assisted pretreatments

Slow degradation rate of swine wastewater, which is mainly caused by particulate and refractory organic matters, is the main drawback of anaerobic digestion. Therefore, it is necessary to improve the hydrolysis of swine wastewater. In this study, different pretreatments were used to hydrolyze swine wastewater, including thermophilic bacteria (TB), alkali, acid, ultrasound (UL), and ultrasonic-combined thermophilic bacteria (UL-TB) pretreatment. The hydrolysis effect was investigated by analyzing the changes of pretreated soluble chemical oxygen demand (SCOD), soluble protein, and carbohydrate. The experimental results showed that effect of different pretreatments on swine wastewater hydrolysis had the following order: TB = alkali>UL-TB > UL>acid. Alkali pretreatment was effective for the release of protein from swine wastewater, and TB pretreatment was advantageous for carbohydrate release during hydrolysis. The results could provide valuable information for the disposition of swine wastewater as well as the application of TB-related pretreatments. PRACTITIONER POINTS: TB and alkali pretreatment exhibited the highest hydrolysis ability. The release of carbohydrate by TB was higher than other pretreatments. Ultrasonic assistance generated inhibition on the hydrolysis of TB.

Performance of different macrophytes in the decontamination of and electricity generation from swine wastewater via an integrated constructed wetland-microbial fuel cell process

Plants constitute a major element of constructed wetlands (CWs). In this study, a coupled system comprising an integrated vertical flow CW (IVCW) and a microbial fuel cell (MFC) for swine wastewater treatment was developed to research the effects of macrophytes commonly employed in CWs, Canna indica, Acorus calamus, and Ipomoea aquatica, on decontamination and electricity production in the system. Because of the different root types and amounts of oxygen released by the roots, the rates of chemical oxygen demand (COD) and ammonium nitrogen (NH₄⁺-N) removal from the swine wastewater differed as well. In the unplanted, Canna indica, Acorus calamus, and Ipomoea aquatica systems, the COD removal rates were 80.20%, 88.07%, 84.70%, and 82.20%, respectively, and the NH₄⁺-N removal rates were 49.96%, 75.02%, 70.25%, and 68.47%, respectively. The decontamination capability of the Canna indica system was better than those of the other systems. The average output voltages were 520±42, 715±20, 660±27, and 752±26mV for the unplanted, Canna indica, Acorus calamus, and Ipomoea aquatica systems, respectively, and the maximum power densities were 0.2230, 0.4136, 0.3614, and 0.4964W/m³, respectively. Ipomoea aquatica had the largest effect on bioelectricity generation promotion. In addition, electrochemically active bacteria, Geobacter and Desulfuromonas, were detected in the anodic biofilm by high-throughput sequencing analysis, and Comamonas (Proteobacteria), which is widely found in MFCs, was also detected in the anodic biofilm. These results confirmed the important role of plants in IVCW-MFCs.

Effect of anolytic nitrite concentration on electricity generation and electron transfer in a dual-chamber microbial fuel cell

This study reports the effect of anolytic nitrite concentration on electricity generation and electron transfer in microbial fuel cells (MFCs). Anolytic nitrite enhanced the electricity generation capability of the MFCs at relatively low concentrations (< 60 mg·L^-1) but inhibited the activity of anodic electrogenic bacteria at high concentrations. In the anode chamber of the MFC, nitrite was converted to nitrate-releasing electrons before being quickly removed through denitrification. Nitrite alone (in the absence of organic matters) could not perform as an electricity production matrix but promoted electricity production as a co-matrix in the MFC. At an influent nitrite concentration of 60 mg·L^-1, the coulombic efficiency of the MFC was minimized at approximately 5.4%, and the charge transfer resistance was also lowest, while the concentrations of extracellular polymeric substances (EPS) and cytochrome c were both maximized. Higher anolytic nitrite concentrations (> 60 mg·L^-1) inhibited the production of cytochrome c and EPS and increased the charge transfer resistance, thereby reducing the efficiency of electron transfer in the anodic biofilm. The results provide valuable guidelines for MFC applications in wastewater treatment processes with nitrite-containing influents.

Combination of plasma oxidation process with microbial fuel cell for mineralizing methylene blue with high energy efficiency

Plasma advanced oxidation process (PAOP) has great ability to break recalcitrant pollutants into small molecular compounds but suffers from poor performance and low energy efficiency for mineralizing dyeing pollutants. Combining advanced oxidation process with biodegradation process is an effective strategy to improve mineralization performance and reduce cost. In this study, a combined process using PAOP as pre-treatment followed by microbial fuel cell (MFC) treatment was investigated to mineralize methylene blue (MB). The PAOP could degrade MB by 97.7%, but only mineralize MB by 23.2% under the discharge power of 35 W for 10 min. Besides, BOD₅/COD ratio of MB solution raised from 0.04 to 0.38 while inhibition on E. coli growth decreased from 85.5% to 28.3%. The following MFC process increased MB mineralization percentage to 63.0% with a maximum output power density of 519 mW m^-2. The combined process achieved a mineralization energy consumption of 0.143 KWh gTOC^-1 which was only 41.8% of that of PAOP. FT-IR, UV-vis and pH variation demonstrated that PAOP could break the aromatic and heterocyclic structures in MB molecule to form organic acids. Possible degradation pathways of MB were accordingly proposed based on LC-MS, GC-MS, and density functional theory calculation.

Kinetic modeling of anaerobic carboxylic acid production from swine wastewater

This work aimed to evaluate the potential of anaerobic carboxylic acids (CA) production from swine wastewater (SW), perform modeling studies of the acidogenic process and estimate the kinetic parameters. Tests were carried out in four batch reactors with 250 mL reaction volume, with brewery sludge as inoculum and using chloroform (0.05%, v/v) for methanogenesis inhibition. Hydrolysis was the main limiting step of CA production from SW, once that it took more than twenty days for the particulate COD consumption to stabilize and fourteen days to produce 60% of the acids formed. A yield of 0.33 mg mgCOD_A^-1, corresponding to 0.40 mgCOD mgCOD_A^-1, was obtained. Kinetic models describing logistic growth functions were best suited to simulate CA production.

Functional group surface modifications for enhancing the formation and performance of exoelectrogenic biofilms on the anode of a bioelectrochemical system

Various new energy technologies have been developed to reduce reliance on fossil fuels. The bioelectrochemical system (BES), an integrated microbial-electrochemical energy conversion process, is projected to be a sustainable and environmentally friendly energy technology. However, low power density is still one of the main limiting factors restricting the practical application of BESs. To enhance power output, functional group modification on anode surfaces has been primarily developed to improve the bioelectrochemical performances of BESs in terms of startup, power density, chemical oxygen demand (COD) removal and coulombic efficiency (CE). This modification could change the anode surface characteristics: roughness, hydrophobicity, biocompatibility, chemical bonding and electrochemically active surface area. This will facilitate bacterial adhesion, biofilm formation and extracellular electron transfer (EET). Additionally, some antibacterial functional groups are applied on air cathodes in order to suppress aerobic biofilms and enhance cathodic oxygen reduction reactions (ORRs). Various modification strategies such as: soaking, heat treatment and plasma modification have been reported to introduce functional groups typically as O-, N- and S-containing groups. In this review, the effects of anode functional groups on electroactive bacteria through the whole biofilm formation process are summarized. In addition, the application of those modification technologies to improve bioelectricity generation, resource recovery, bioelectrochemical analysis and the production of value-added chemicals and biofuels is also discussed. Accordingly, this review aims to help scientists select the most appropriate functional groups and up-to-date methods to improve biofilm formation.

Scaling up Microbial Fuel Cells for Treating Swine Wastewater

Conventional aerobic treatment of swine wastewater, which generally contains 4500–8200 mg L−1 of organic matter, is energy-consuming. The aim of this study was to assess the application of scaled-up microbial fuel cells (MFCs) with different capacities (i.e., 1.5 L, 12 L, and 100 L) for removing organic matter from swine wastewater. The MFCs were single-chambered, consisting of an anode of microbially reduced graphene oxide (rGO) and an air-cathode of platinum-coated carbon cloth. The MFCs were polarized via an external resistance of 3–10 Ω for 40 days for the 1.5 L-MFC and 120 days for the 12L- and 100 L-MFC. The MFCs were operated in continuous flow mode (hydraulic retention time: 3–5 days). The 100 L-MFC achieved an average chemical oxygen demand (COD) removal efficiency of 52%, which corresponded to a COD removal rate of 530 mg L−1 d−1. Moreover, the 100 L-MFC showed an average and maximum electricity generation of 0.6 and 2.2 Wh m−3, respectively. Our findings suggest that MFCs can effectively be used for swine wastewater treatment coupled with the simultaneous generation of electricity.

Enhancing the power performance of sediment microbial fuel cells by novel strategies: Overlying water flow and hydraulic-driven cathode rotating

Sediment microbial fuel cells (SMFCs) are promising power sources for environmental monitoring in remote areas and environment-friendly solutions to river sediment contamination. However, cathodic limitations will significantly decrease power performance and limit its practical application. In this work, the control SMFC (SMFC-C) with cathode horizontally and fully submerged below the overlying water, and the hydraulic-driven rotating cathode SMFC (SMFC-R) was constructed. Overlying water flow and hydraulic-driven cathode rotating as novel strategies for SMFCs towards field applications were proposed. Results demonstrated that better power performance under static condition was obtained in SMFC-R than in SMFC-C, that the overlying water flow could significantly increase the maximum power density (MPD) in SMFC-C over the static condition, and that the cathode rotating further improved MPD in SMFC-R. The MPD obtained under static condition were 26.5 mW/m² and 45.1 mW/m² in SMFC-C and SMFC-R, which increased to 38.8 mW/m² and 47.3 mW/m² under water flow and cathode rotating condition, respectively. Analyses on cathode potential, overlying water pH and dissolved oxygen suggested severe cathodic limitations in SMFC-C under static condition which could be diminished by overlying water flow. However, almost no such limitations were observed in SMFC-R even under static condition, which is probably due to the fact that the cathodic oxygen reaction in SMFC-R mainly occurred on the cathode exposed to the air rather than on that submerged below the water. Identical anode performance was obtained in both SMFCs under different conditions, which were not an influencing factor leading to different power performance.

Enhancement of the denitrification activity by exoelectrogens in single-chamber air cathode microbial fuel cells

Single-chamber microbial fuel cells (MFCs) can efficiently treat wastewater containing nitrate, probably because the interaction between exoelectrogens and denitrifying bacteria may enhance the denitrification activity of MFCs. In this study, the denitrification of nitrate with a wide range of concentrations was investigated by using single-chamber air cathode MFCs. The maximum average denitrification rate of the MFCs inoculated and operated under closed-circuit conditions (Group N-CC) was up to 12.2 ± 0.6 kg NO₃^--N m^-3 d^-1 at a high nitrate concentration of 2000 mg NO₃-N L^-1, which was 74.3% higher than that of the MFCs inoculated and operated under open-circuit conditions and which was significantly higher than those of other MFC systems and many traditional bioreactors. The high denitrification activity of the MFCs of Group N-CC was attributed to the significant reduction of nitrite accumulation through the possible bioelectrochemical nitrite reduction by exoelectrogens that were only enriched at the anodes of the MFCs of Group N-CC. In addition, the MFCs of Group N-CC showed good stability (over 3.5 years) and low apparent activation energy (34.0 kJ mol^-1) of the denitrification, indicating the good coexistence of exoelectrogens (Geobacter) and denitrifying bacteria (Thauera) with high performance on denitrification during the long-term operation.

Bioremediation of wastewater through a quorum sensing triggered MFC: A sustainable measure for waste to energy concept

A mission for fast advancement has constrained us to unpredictably tap various natural assets. The reckless utilisation of fossil fuels led unmanageable wastes which have greatly affected our health and environment. Endeavours to address these difficulties have conveyed to the frontal area certain creative natural solutions particularly the utilisation of microbial digestion systems. In the previous two decades, the microbial fuel cell (MFC) innovation has caught the consideration of the researchers. The MFCs is a kind of bio-electrochemical framework with novel highlights, for example, power production, wastewater treatment, and biosensor applications. Lately, dynamic patterns in MFC inquire about on its synthetic, electrochemical, and microbiological perspectives have brought about its observable applications. The MFCs have begun as a logical interest, and in numerous regards, these remaining parts to be the situation. This is especially a result of the multidimensional uses of this eco-accommodating innovation. The innovation relies upon the electroactive microorganisms, prominently known as exoelectrogens. In the first place, it is the main innovation that can create energy out of waste, without the contribution of outer/extra energy. Modification of electrodes with nanomaterials, for example, gold nanoparticles and iron oxide nanoparticles or pretreatment techniques, for example, sonication and autoclave disinfection have indicated promising outcomes in improving MFC execution for power generation and wastewater treatment. The MFC innovation has been likewise explored for the remediation of different heavy metals and hazardous components, and to recognize the poisonous components in wastewater. What's more, the MFCs can be adjusted into microbial electrolysis cells to produce hydrogen energy from different natural sources. This article gives a thorough and cutting-edge appraisal of the novel magnitudes of the MFC.

Organic matter and ammonia removal by a novel integrated process of constructed wetland and microbial fuel cells

A novel approach, combining a microbial fuel cell (MFC) with an integrated vertical flow constructed wetland (IVCW), was developed, and its ability to simultaneously produce electrical energy while treating swine wastewater was verified. The system combined the singular water flow path of a traditional vertical flow constructed wetland (upflow and downflow)-microbial fuel cell (CW-MFC), which demonstrates better characteristics in the aerobic, anoxic, and anaerobic regions. It not only enhanced the anti-pollution load ability and the organic compound removal effect, but also improved the gradient difference in the redox potential of the system. The results showed that the structure and substrate distribution in the device could both improve swine wastewater treatment and increase bioelectricity generation capabilities. The average chemical oxygen demand (COD) and ammonia nitrogen (NH4 +-N) removal efficiencies were as high as 79.65% and 77.5%, respectively. Long-term and stable bioelectricity generation was achieved under continuous flow conditions. The peak values of the output voltage and power density were 713 mV and 456 mW m-3. The activated carbon layer at the bottom of this system provided a larger surface for the growth of microbes. It showed significant promotion of the relative abundance of electrochemically active bacteria, which might result in the increase of bioelectricity generation in integrated vertical flow constructed wetland-microbial fuel cells (IVCW-MFCs). The electrochemically active bacteria, Geobacter and Desulfuromonas, were detected in the anodic biofilm by high-throughput sequencing analysis.

A photosynthetic algal microbial fuel cell for treating swine wastewater

A photosynthetic algal (Chlorella vulgaris) microbial fuel cell (PAMFC) with double chambers was adopted for power production and removal of carbon and nitrogen in swine sewerage that could provide nutrients for the growth of C. vulgaris. C. vulgaris was expected to utilize carbon dioxide (CO₂) delivered from the anode chamber and generate oxygen as an electron acceptor by photosynthesis. PAMFC presented a maximum voltage output of 0.747 V and a maximum power density of 3720 mW/m³ at 240 h, much higher than that of the standalone MFC. 85.6%, 70.2%, and 93.9% removal of ammonia nitrogen, total nitrogen (TN), and total organic carbon (TOC), respectively, were obtained in the anode chamber of the PAMFC system, while the corresponding removal in MFC was 83.1%, 56.0%, and 87.2%, respectively. PAMFC also presented a much higher removal of ammonia nitrogen (68.7%) in the cathode chamber than MFC (47.5%). The results indicated the superiority of the PAMFC device for carbon and nitrogen removal.

Evaluation of ammonia recovery from swine wastewater via a innovative spraying technology

An innovative spraying system for NH₄⁺-N removal and recovery was investigated under different pH, temperature, spraying frequency and rate by using spraying system. Results showed that NH₄⁺-N removal efficiency and mass transfer coefficient (K_La) value in swine wastewater (SW) remarkably increased with increasing of temperature, spraying frequency and rate due to promoting the diffusion of NH₃ molecules caused by increasing specific surface of SW molecule, and high shear force and temperature difference between SW and circulating heating tube. Considering the cost and discharge standard, the optimum parameters for NH₄⁺-N removal from SW using spraying system were alkaline, 0.24 m³ h^-1 of continuous spraying, and 45 °C circulating water, and the NH₄⁺-N decreased from 591.2 to 68.9 mg L^-1 (<80 mg L^-1) after 8 h treatment, and this value corresponded to 88.35% removal rate. Furthermore, over 85% recovery rate for NH₄⁺-N could be obtained through absorption of phosphoric acid.

Microbial fuel cell and membrane bioreactor coupling system: recent trends

Membrane bioreactor (MBR) and microbial fuel cell (MFC) are new technologies based on microbial process. MBR takes separation process as the core to achieve the high efficient separation and enrichment the beneficiation of microbes during the biological treatment. MFC is a novel technology based on electrochemical process to realize the mutual conversion between biomass energy and electric energy, in order to solve the problems of serious membrane fouling and low efficiency of denitrification in membrane bioreactor, the low power generation efficiency, and unavailability of bioelectric energy of MFC. In recent years, MFC-MBR coupling system emerged. It can effectively mitigate the membrane fouling and reduce the excess sludge production. Simultaneously, the electricity can be used effectively. The new coupling system has good prospects for development. In this paper, we summarized the research progresses of the two kinds of coupling systems in recent years and analyzed the coupling structure and forms. Based on the above, the future development fields of the MFC-MBR coupling system were prospected.

Factors Affecting the Effectiveness of Bioelectrochemical System Applications: Data Synthesis and Meta-Analysis

Microbial fuel cells (MFCs) and microbial electrolysis cells (MECs) are promising bioelectrochemical systems (BESs) for simultaneous wastewater treatment and energy/resource recovery. Unlike conventional fuel cells that are based on stable chemical reactions, these BESs are sensitive to environmental and operating conditions, such as temperature, pH, external resistance, etc. Substrate type, electrode material, and reactor configuration are also important factors affecting power generation in MFCs and hydrogen production in MECs. In order to discuss the influence of these above factors on the performance of MFCs and MECs, this study analyzes published data via data synthesis and meta-analysis. The results revealed that domestic wastewater would be more suitable for treatment using MFCs or MECs, due to their lower toxicity for anode biofilms compared to swine wastewater and landfill leachate. The optimal temperature was 25–35 °C, optimal pH was 6–7, and optimal external resistance was 100–1000 Ω. Although systems using carbon cloth as the electrodes demonstrated better performance (due to carbon cloth’s large surface area for microbial growth), the high prices of this material and other existing carbonaceous materials make it inappropriate for practical applications. To scale up and commercialize MFCs and MECs in the future, enhanced system performance and stability are needed, and could be possibly achieved with improved system designs.

Treatment of soak liquor and bioelectricity generation in dual chamber microbial fuel cell

The discharge of untreated soak liquor from tannery industry causes severe environmental pollution. This study is characterizing the soak liquor as a substrate in the microbial fuel cell (MFC) for remediation along with electricity generation. The dual chamber MFC was constructed and operated. Potassium permanganate was used as cathode solution and carbon felt electrode as anodic and cathodic material, respectively. The soak liquor was characterized by electrochemical studies viz., cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and polarization studies, respectively. The removal percentage of protein, lipid, and chemical oxygen demand (COD) were measured before and after treatment with MFC. The results of MFC showed a highest current density of 300 mA/cm² and a power density of 92 mW/m². The removal of COD, protein, and lipid were noted as 96, 81, and 97% respectively during MFC process. This MFC can be used in tannery industries for treating soak liquor and simultaneous electricity generation.