Adsorption of selected organic micro-pollutants on sewage sludge biochar

A critical review on emerging industrial applications of chars from thermal treatment of biosolids

Thermochemical treatment is rapidly emerging as an alternative method for the management of stabilised sewage sludges (biosolids) to effectively reduce waste volume, degrade contaminants, and generate valuable products, particularly biochar and hydrochar. Biosolids-derived char has a relatively high concentration of heavy metals compared with agricultural chars but is still applied to land due to its beneficial properties and ability to retain metals. However, non-agricultural applications can provide additional economic and environmental benefits, promote sustainability and support a circular economy. This review identifies extensive non-agricultural opportunity for biosolids biochar, including adsorption, catalysis, energy storage systems, biological process enhancement, and as additives for rubber compounding and construction. Biosolids chars have received limited attention vs agricultural char, and we draw on both areas of literature, as well as evaluating differences between agricultural and biosolids chars. A key opportunity for biosolids biochar in comparison with other materials and agricultural chars is its sustainable and low-cost nature, relatively high metals content, improving catalyst properties, and ability to modify in various stages to tune it to specific applications. The specific opportunities for hydrochar have only received limited attention. Research needs to include better understanding of the benefits and limitations for specific applications, as well as adjacent drivers, including society, regulation, and market and economics.

Biochar Applications for Efficient Removal of Energetic Compound Contaminants

Military activities and the production or disposal of ammunition often lead to soil contamination with energetic compounds (ECs) such as dinitrotoluene, trinitrotoluene, and hexogen, posing significant threats to human health and the ecosystem. Biochar has emerged as a cost-effective and widely available solution for remediating contaminated sites characterized by its capacity for pollutant removal through adsorption and conversion process, along with minimal secondary pollution. This paper provides a comprehensive review of relevant literature on biochar's efficacy in eliminating ECs, including an analysis of the underlying mechanisms. The discussion addresses challenges and opportunities associated with biochar application in ECs remediation, offering insights for future research directions. In summary, the use of biochar for ECs removal presents a promising and eco-friendly approach, facilitating the remediation of contaminated sites while promoting soil function and ecosystem recovery.

Graphite-N reinforced sludge biochar electrode: A experimental and DFT theoretical analysis of efficient evolution and in-situ utilization of H2O2

Rational reuse of municipal sludge to produce electro-Fenton electrode can not only save resources, but also produce superior peroxide and degradation pollutants simultaneously. Herein, a novel electro-Fenton electrode derived from sludge biochar loaded on Ni foam (SBC@Ni) was constructed via high temperature pyrolysis and chemical coating for efficient H2O2 evolution and pollutant degradation. Systematic experiments and density functional theory calculations (DFT calculation) explained that the production of graphite C and graphite N during high-temperature pyrolysis of municipal sludge can greatly enhance the oxygen reduction reaction of SBC@Ni electrode and promote the evolution of H2O2. And the hybrid heterojunctions, such as FeP, also played a key role in electrocatalytic processes. Notably, the electrode still exhibited excellent performance after 1000 linear scans and 12 h of continuous current stimulation, which demonstrated the excellent stability of the electrode. Moreover, SBC@Ni electrode can not only effectively oxidize 4-chlorophenol through the electro-Fenton effect, but also fully mineralize organic matter, indicating promising environmental application. The free radical quenching experiment also revealed that the ·OH is the main active species for 4-CP degradation in SBC@Ni electro-Fenton system.

Engineered lignocellulosic based biochar to remove endocrine-disrupting chemicals: Assessment of binding mechanism

The safety and health of aquatic organisms and humans are threatened by the increasing presence of pollutants in the environment. Endocrine disrupting chemicals are common pollutants which affect the function of endocrine and causes adverse effects on human health. These chemicals can disrupt metabolic processes by interacting with hormone receptors upon consumptions by humans or aquatic species. Several studies have reported the presence of endocrine disrupting chemicals in waterbodies, food, air and soil. These chemicals are associated with increasing occurrence of obesity, metabolic disorders, reproductive abnormalities, autism, cancer, epigenetic variation and cardiovascular risk. Conventional treatment processes are expensive, not environment friendly and unable to achieve complete removal of these harmful chemicals. In recent years, biochar from different sources has gained a considerable interest due to their adsorption efficiency with porous structure and large surface areas. biochar derived from lignocellulosic biomass are widely used as sustainable catalysts in soil remediation, carbon sequestration, removal of organic and inorganic pollutants and wastewater treatment. This review conceptualizes the production techniques of biochar from lignocellulosic biomass and explores the functionalization and interaction of biochar with endocrine-disrupting chemicals. This review also identifies the further needs of research. Overall, the environmental and health risks of endocrine-disrupting chemicals can be dealt with by biochar produced from lignocellulosic biomass as a sustainable and prominent approach.

Co-regulating the pore structure and surface chemistry of sludge-based biochar for high-performance deodorization of gaseous dimethyl disulfide

A straightforward and eco-friendly preparation method for porous sludge biochar (SBA-3) was developed to deodorize gaseous dimethyl disulfide (DMDS) using ion exchange to adjust micropore structures coupled with carboxyl functionalization. Compared with the unmodified sludge biochar SBA-1 and SBA-2 treated with ion exchange, the pore size of SBA-3 decreased accompanied with increasing specific surface area and micropore volume. The Brunauer-Emmett-Teller (BET) specific surface area and micropore volume were 176.35 and 0.0314 cm³ g-1, which were 2.02 and 1.71-fold larger than those of SBA-2, as well as 20.60 and 78.5-fold larger than those of SBA-1, respectively. Meanwhile, the amount of -COOH on the surface of SBA-3 increased from 0.425 to 1.123 mmol g-1, which was 2.64-fold larger than that of SBA-1. The adsorption behavior between DMDS and SBA-3 could be well described by the quasi-second-order kinetic model and Langmuir isotherm model. The maximum monolayer adsorption capacity was 35.12 mg g-1 at 303 K. Thermodynamic and DFT calculations indicated that the adsorption of DMDS on SBA-3 was exothermic with the deodorization mechanisms involving pore filling and chemisorption.

Advanced oxidation process for the treatment of industrial wastewater: A review on strategies, mechanisms, bottlenecks and prospects

Due to its complex and, often, highly contaminated nature, treating industrial wastewater poses a significant environmental problem. Many of the persistent pollutants found in industrial effluents cannot be effectively removed by conventional treatment procedures. Advanced Oxidation Processes (AOPs) have emerged as a promising solution, offering versatile and effective means of pollutant removal and mineralization. This comprehensive review explores the application of various AOP strategies in industrial wastewater treatment, focusing on their mechanisms and effectiveness. Ozonation (O3): Ozonation, leveraging ozone (O3), represents a well-established AOP for industrial waste water treatment. Ozone's formidable oxidative potential enables the breakdown of a broad spectrum of organic and inorganic contaminants. This paper provides an in-depth examination of ozone reactions, practical applications, and considerations involved in implementing ozonation. UV/Hydrogen Peroxide (UV/H2O2): The combination of ultraviolet (UV) light and hydrogen peroxide (H2O2) has gained prominence as an AOP due to its ability to generate hydroxyl radicals (ȮH), highly efficient in pollutant degradation. The review explores factors influencing the efficiency of UV/H2O2 processes, including H2O2 dosage and UV radiation intensity. Fenton and Photo-Fenton Processes: Fenton's reagent and Photo-Fenton processes employ iron ions and hydrogen peroxide to generate hydroxyl radicals for pollutant oxidation. The paper delves into the mechanisms, catalyst selection, and the role of photoactivation in enhancing degradation rates within the context of industrial wastewater treatment. Electrochemical Advanced Oxidation Processes (EAOPs): EAOPs encompass a range of techniques, such as electro-Fenton and anodic oxidation, which employ electrode reactions to produce ȮH radicals. This review explores the electrochemical principles, electrode materials, and operational parameters critical for optimizing EAOPs in industrial wastewater treatment. TiO2 Photocatalysis (UV/TiO2): Titanium dioxide (TiO2) photocatalysis, driven by UV light, is examined for its potential in industrial wastewater treatment. The review investigates TiO2 catalyst properties, reaction mechanisms, and the influence of parameters like catalyst loading and UV intensity on pollutant removal. Sonolysis (Ultrasonic Irradiation): High-frequency ultrasound-induced sonolysis represents a unique AOP, generating ȮH radicals during the formation and collapse of cavitation bubbles. This paper delves into the physics of cavitation, sonolytic reactions, and optimization strategies for industrial wastewater treatment. This review offers a critical assessment of the applicability, advantages, and limitations of these AOP strategies in addressing the diverse challenges posed by industrial wastewater. It emphasizes the importance of selecting AOPs tailored to the specific characteristics of industrial effluents and outlines potential directions for future research and practical implementation. The integrated use of these AOPs, when appropriately adapted, holds the potential to achieve sustainable and efficient treatment of industrial wastewater, contributing significantly to environmental preservation and regulatory compliance.

Effective adsorption of bisphenol A from aqueous solution using phosphoric acid-assisted hydrochar

Sycamore leaf biochar (PSAC) was prepared by a two-step phosphoric acid-assisted hydrothermal carbonization combined with a short-time activation method. The characterization results showed that the introduction of phosphoric acid molecules and thermal activation resulted in a substantial increase in the specific surface area (994.21 m2/g) and microporous capacity (0.307 cm3/g) of PSAC. The batch adsorption results showed that the adsorption process of PSAC on bisphenol A (BPA) was best described by the pseudo-second-order kinetic model and Sips isothermal model, with a maximum adsorption capacity of 247.42 mg/g. The adsorption of BPA onto PSAC was determined to be a spontaneous endothermic process. The equilibrium adsorption capacity of PSAC exhibited an upward trend with increasing initial BPA concentration and temperature while decreasing with higher adsorbent dosage and pH value. Coexisting cations and humic acids in water have little impact on the adsorption performance of PSAC for BPA. The adsorption mechanism of BPA by PSAC was mainly governed by pore filling and hydrogen bonding interactions, π-π interactions, and intraparticle diffusion. Furthermore, PSAC demonstrated good reusability by its sustained adsorption capacity of BPA, which remained at 82.6% of the initial adsorption capacity even after four adsorption-desorption cycles. These findings highlight the potential of utilizing low-cost sycamore leaf biochar as an effective adsorbent for the removal of the endocrine disruptor BPA.

Recent progress in the production and application of biochar and its composite in environmental biodegradation

Over the past few decades, extensive research has been conducted to develop cost-effective and high-quality biochar for environmental biodegradation purposes. Pyrolysis has emerged as a promising method for recovering biochar from biomass and waste materials. This study provides an overview of the current state-of-the-art biochar production technology, including the advancements and biochar applications in organic pollutants remediation, particularly wastewater treatment. Substantial progress has been made in biochar production through advanced thermochemical technologies. Moreover, the review underscores the importance of understanding the kinetics of pollutant degradation using biochar to maximize its synergies for potential environmental biodegradation. Finally, the study identifies the technological gaps and outlines future research advancements in biochar production and its applications for environmental biodegradation.

2-Methyl-4-chlorophenoxyacetic acid (MCPA) sorption and desorption as a function of biochar properties and pyrolysis temperature

2-Methyl-4-chlorophenoxyacetic acid (MCPA) is a highly mobile herbicide that is frequently detected in global potable water sources. One potential mitigation strategy is the sorption on biochar to limit harm to unidentified targets. However, irreversible sorption could restrict bioefficacy thereby compromising its usefulness as a vital crop herbicide. This research evaluated the effect of pyrolysis temperatures (350, 500 and 800°C) on three feedstocks; poultry manure, rice hulls and wood pellets, particularly to examine effects on the magnitude and reversibility of MCPA sorption. Sorption increased with pyrolysis temperature from 350 to 800°C. Sorption and desorption coefficients were strongly corelated with each other (R2 = 0.99; P < .05). Poultry manure and rice hulls pyrolyzed at 800°C exhibited irreversible sorption while for wood pellets at 800°C desorption was concentration dependent. At higher concentrations some desorption was observed (36% at 50 ppm) but was reduced at lower concentrations (1-3% at < 5 ppm). Desorption decreased with increasing pyrolysis temperature. Sorption data were analyzed with Langmuir, Freundlich, Dubinin-Radushkevich and Temkin isotherm models. Freundlich isotherms were better predictors of MCPA sorption (R2 ranging from 0.78 to 0.99). Poultry manure and rice hulls when pyrolyzed at higher temperatures (500 and 800°C) could be used for remediation efforts (such as spills or water filtration), due to the lack of desorption observed. On the other hand, un-pyrolyzed feedstocks or biochars created at 350°C could perform superior for direct field applications to limit indirect losses including runoff and leaching, since these materials also possess the ability to release MCPA subsequently to potentially allow herbicidal action.

Viable remediation techniques to cleansing wastewaters comprising endocrine-disrupting compounds

Endocrine-disrupting chemicals (EDCs) have recently gained prominence as emerging pollutants due to their significant negative impacts on diverse living forms in ecosystems, including humans, by altering their endocrine systems. EDCs are a prominent category of emerging contaminants in various aquatic settings. Given the growing population and limited access to freshwater resources, their expulsion from aquatic systems is also a severe issue. EDC removal from wastewater depends on the physicochemical properties of the specific EDCs found in each wastewater type and various aquatic environments. Due to these components' chemical, physical, and physicochemical diversity, various approaches based on physical, biological, electrochemical, and chemical procedures have been developed to eliminate them. The objective of this review is to provide the comprehensive overview by selecting recent approaches that showed significant impact on the best available methods for removing EDCs from various aquatic matrices. It is suggested that adsorption by carbon-based materials or bioresources is effective at higher EDC concentrations. Electrochemical mechanization works, but it requires expensive electrodes, continual energy, and chemicals. Due to the lack of chemicals and hazardous byproducts, adsorption and biodegradation are considered environmentally friendly. When combined with synthetic biology and an AI system, biodegradation can efficiently remove EDCs and replace conventional water treatment technologies in the near future. Hybrid in-house methods may reduce EDCs best, depending on the EDC and resources.

Production and characterization of graphene oxide-engineered biochars and application for organic micro-pollutant adsorption from aqueous solutions

In this study, conventional and Graphene Oxide-engineered biochars were produced and thoroughly characterized, in order to investigate their potential as adsorptive materials. Two types of biomass, Rice Husks (RH) and Sewage Sludge (SS), two Graphene Oxide (GO) doses, 0.1% and 1%, and two pyrolysis temperatures, 400 °C and 600 °C were investigated. The produced biochars were characterized in physicochemical terms and the effect of biomass, GO functionalization and pyrolysis temperature on biochar properties was studied. The produced samples were then applied as adsorbents for the removal of six organic micro-pollutants from water and treated secondary wastewater. Results showed that the main factors affecting biochar structure was biomass type and pyrolysis temperature, while GO functionalization caused significant changes on biochar surface by increasing the available C- and O- based functional groups. Biochars produced at 600 °C showed higher C content and Specific Surface Area, presenting more stable graphitic structure, compared to biochars produced at 400 °C. Micro-pollutant adsorption rates were in the range of 39.9%-98.3% and 9.4%-97.5% in table water and 28.3%-97.5% and 0.0%-97.5% in treated municipal wastewater, for the Rice Husk and Sewage Sludge biochars respectively. The best biochars, in terms of structural properties and adsorption efficiency were the GO-functionalized biochars, produced from Rice Husks at 600 °C, while the most difficult pollutant to remove was 2.4-Dichlorophenol.

Sequestration of steroidal estrogen in aqueous samples using an adsorption mechanism: a systemic scientometric review

Steroidal estrogens (SEs) remain one of the notable endocrine disrupting chemicals (EDCs) that pose a significant threat to the aquatic environment in this era owing to their interference with the normal metabolic functions of the human body systems. They are currently identified as emerging contaminants of water sources. The sources of SEs are either natural or synthetic active ingredients in oral contraceptive and hormonal replacement therapy drugs and enter the environment primarily from excretes in the form of active free conjugate radicals, resulting in numerous effects on organisms in aquatic habitats and humans. The removal of SEs from water sources is of great importance because of their potential adverse effects on aquatic ecosystems and human health. Adsorption techniques have gained considerable attention as effective methods for the removal of these contaminants. A systemic review and bibliometric analysis of the application of adsorption for sequestration were carried out. Metadata for publications on SE removal utilizing adsorbents were obtained from the Web of Science (WoS) from January 1, 1990, to November 5, 2022 (107 documents) and Scopus databases from January 1, 1949, to November 5, 2022 (77 documents). In total, 137 documents (134 research and 4 review articles) were used to systematically map bibliometric indicators, such as the number of articles, most prolific countries, most productive scholars, and most cited articles, confirming this to be a growing research area. The use of different adsorbents, include activated carbon graphene-based materials, single and multi-walled carbon nanotubes, biochar, zeolite, and nanocomposites. The adsorption mechanism and factors affecting the removal efficiency, such as pH, temperature, initial concentration, contact time and adsorbent properties, were investigated in this review. This review discusses the advantages and limitations of different adsorbents, including their adsorption capacities, regenerative potential, and cost-effectiveness. Recent advances and innovations in adsorption technology, such as functionalized materials and hybrid systems, have also been highlighted. Overall, the bibliographic analysis provides a comprehensive overview of the adsorption technique for the removal of SEs from other sources, serving as a valuable resource for researchers and policymakers involved in the development of efficient and sustainable strategies to mitigate the effects of these emerging contaminants.

Sewage sludge biochars as effective PFAS-sorbents

The use of sewage sludge to produce biochar-based sorbents for per- and polyfluoroalkyl substances (PFAS) removal from water and soil may be an economically and environmentally sustainable waste management option. This study compared the sorption of six perfluorinated carboxylic acids (PFCAs) by two sewage sludge biochars (SSBCs) and one wood chip biochar (WCBC), dry pyrolyzed at 700 °C. Batch sorption tests were conducted by adding individual PFCAs and a PFCA-mixture to pure biochars and mixtures of biochar and a sandy soil (1.3% TOC). PFAS-sorption to the SSBCs exhibited log-linear biochar-water distribution coefficients (log K_d), comparable to those previously reported for commercial activated carbons (e.g., 5.73 ± 0.02 for perfluorooctanoic acid at 1 µg/L). The strong sorption of PFCAs was attributed to the SSBCs relatively high pore volumes in the pore size range that can accommodate these compounds. Sorption was attenuated by the presence of soil (by factors 3-10), by the presence of a mixture of PFCAs (by factors of 6-532) and by both together (by factors of 8-6581), indicating strongly competitive sorption between PFCA-congeners, and less severe sorption attenuation by soil organic matter. These findings could enable sustainable value chains for SSBs in soil remediation and water filtration solutions.

Fabrication of novel Fe/Mn/N co-doped biochar and its enhanced adsorption for bisphenol a based on π-π electron donor-acceptor interaction

In this work, a novel Fe/Mn/N co-doped biochar (Fe&Mn-NBC800) derived from waste apple tree branches was fabricated for bisphenol A (BPA) removal. Fe&Mn-NBC800 exhibited higher adsorption capacity (84.96 mg·g-1) in 318 K for BPA than the pristine biochar, doped mono-atomic, and di-atomic biochar. Higher temperature and adsorbent dosage promoted BPA removal, while higher solution pH was detrimental to the adsorption process. The kinetic and isothermal processes of BPA removal followed the pseudo-second-order model and Langmuir, respectively. Characterizations and correlation analysis indicated that π-π interactions showed the major contribution to the BPA adsorption. Furthermore, the pore filling, electrostatic interactions, hydrogen bonding, and hydrophobic interactions also played a role. Good water environment anti-interference ability (ion species, ionic strength, actual water body) and excellent recyclability of Fe&Mn-NBC800 make it exhibit the potential for engineering projects.

Review on carbon-based adsorbents from organic feedstocks for removal of organic contaminants from oil and gas industry process water: Production, adsorption performance and research gaps

Large amounts of process water with considerable concentrations of recalcitrant organic contaminants, such as polycyclic aromatic hydrocarbon (PAHs), phenolic compounds (PCs), and benzene, toluene, ethylbenzene, and xylene (BTEX), are generated by several segments of oil and gas industries. These segments include refineries, hydraulic fracturing (HF), and produced waters from the extraction of shale gas (SGPW), coalbed methane (CBMPW) and oil sands (OSPW). In fact, the concentration of PCs and PAHs in process water from refinery can reach 855 and 742 mg L^-1, respectively. SGPW can contain BTEX at concentrations as high as 778 mg L^-1. Adsorption can effectively target those organic compounds for the remediation of the process water by applying carbon-based adsorbents generated from organic feedstocks. Such organic feedstocks usually come from organic waste materials that would otherwise be conventionally disposed of. The objective of this review paper is to cover the scientific progress in the studies of carbon-based adsorbents from organic feedstocks that were successfully applied for the removal of organic contaminants PAHs, PCs, and BTEX. The contributions of this review paper include the important aspects of (i) production and characterization of carbon-based adsorbents to enhance the efficiency of organic contaminant adsorption, (ii) adsorption properties and mechanisms associated with the engineered adsorbent and expected for certain pollutants, and (iii) research gaps in the field, which could be a guidance for future studies. In terms of production and characterization of materials, standalone pyrolysis or hybrid procedures (pyrolysis associated with chemical activation methods) are the most applied techniques, yielding high surface area and other surface properties that are crucial to the adsorption of organic contaminants. The adsorption of organic compounds on carbonaceous materials performed well at wide range of pH and temperatures and this is desirable considering the pH of process waters. The mechanisms are frequently pore filling, hydrogen bonding, π-π, hydrophobic and electrostatic interactions, and same precursor material can present more than one adsorption mechanism, which can be beneficial to target more than one organic contaminant. Research gaps include the evaluation of engineered adsorbents in terms of competitive adsorption, application of adsorbents in oil and gas industry process water, adsorbent regeneration and reuse studies, and pilot or full-scale applications.

Nanomaterials photocatalytic activities for waste water treatment: a review

Water is necessary for the survival of life on Earth. A wide range of pollutants has contaminated water resources in the last few decades. The presence of contaminants incredibly different dyes in waste, potable, and surface water is hazardous to environmental and human health. Different types of dyes are the principal contaminants in water that need sudden attention because of their widespread domestic and industrial use. The toxic effects of these dyes and their ability to resist traditional water treatment procedures have inspired the researcher to develop an eco-friendly method that could effectively and efficiently degrade these toxic contaminants. Here, in this review, we explored the effective and economical methods of metal-based nanomaterials photocatalytic degradation for successfully removing dyes from wastewater. This study provides a tool for protecting the environment and human health. In addition, the insights into the transformation of solar energy for photocatalytic reduction of toxic metal ions and photocatalytic degradation of dyes contaminated wastewater will open a gate for water treatment research. The mechanism of photocatalytic degradation and the parameters that affect the photocatalytic activities of various photocatalysts have also been reported.

Migration and Deposition Law of Pollutants in Urban Sewage Confluence Pipe Network from the Perspective of Ecology

Aiming at the problem of pollutant migration and deposition in urban sewage confluence pipe, an experimental simulation system of sewage confluence pipe was established. The confluence conditions of three flow patterns (velocity ratio Vaccess/Vtrunk = 0.1/0.2, Vaccess/Vtrunk = 0.1/0.3, and Vaccess/Vtrunk = 0.2/0.3) were simulated. The changes of sediment thickness, carbon pollutants, nitrogen pollutants, and phosphorus pollutants in different confluence areas were analyzed, and the migration and deposition laws of various pollutants in urban sewage confluence pipe network under different flow patterns were revealed. The results show that when the flow velocity of trunk and branch roads changes, the deposition of various pollutants and the carrying capacity of water flow in the pipeline change, resulting in the change of sediment layer thickness and pollutant content. With the increase of trunk velocity, the sediment thickness in the area before and after confluence decreases, while the increase of branch velocity only reduces the sediment thickness in the area at the back of confluence. Under any flow pattern, the sediment thickness in the retention area (G3 and G4) shows an increasing trend, which is the key area of pollution removal. Under the three flow patterns, the content of carbon pollutants reaches the peak at the TCOD and SCOD values of G4 monitoring point. Increasing the trunk velocity can effectively reduce the content of carbon pollutants. The content of nitrogen pollutants in each flow pattern also reaches the maximum at G4 point, which are 213.6 mg/g, 205.2 mg/g, and 212.8 mg/g, respectively. Increasing the trunk velocity can effectively reduce the nitrogen content at points G1-G4, while increasing the flow velocity of the branch road can reduce the nitrogen content at points G5-G7. The distribution of phosphorus pollutants is complex, and the flow pattern needs to be adjusted according to different monitoring points.

A sustainable reuse strategy of converting waste activated sludge into biochar for contaminants removal from water: Modifications, applications and perspectives

Conversion of sewage sludge to biochar for contaminants removal from water achieves the dual purpose of solid waste reuse and pollution elimination, in line with the concept of circular economy and carbon neutrality. However, the current understanding of sludge-derived biochar (SDB) for wastewater treatment is still limited, with a lack of summary regarding the effect of modification on the mechanism of SDB adsorption/catalytic removal aqueous contaminants. To advance knowledge in this aspect, this paper systematically reviews the recent studies on the use of (modified) SDB as adsorbents and in persulfate-based advanced oxidation processes (PS-AOPs) as catalysts for the contaminants removal from water over the past five years. Unmodified SDB not only exhibits stronger cation exchange and surface precipitation for heavy metals due to its nitrogen/mineral-rich properties, but also can provide abundant catalytic active sites for PS. An emphatic summary of how certain adsorption removal mechanisms of SDB or its catalytic performance in PS-AOPs can be enhanced by targeted regulation/modification such as increasing the specific surface area, functional groups, graphitization degree, N-doping or transition metal loading is presented. The interference of inorganic ions/natural organic matter is one of the unavoidable challenges that SDB is used for adsorption/catalytic removal of contaminants in real wastewater. Finally, this paper presents the future perspectives of SDB in the field of wastewater treatment. This review can contribute forefront knowledge and new ideas for advancing sludge treatment toward sustainable green circular economy.

Covalent and Non-covalent Functionalized Nanomaterials for Environmental Restoration

Nanotechnology has emerged as an extraordinary and rapidly developing discipline of science. It has remolded the fate of the whole world by providing diverse horizons in different fields. Nanomaterials are appealing because of their incredibly small size and large surface area. Apart from the naturally occurring nanomaterials, synthetic nanomaterials are being prepared on large scales with different sizes and properties. Such nanomaterials are being utilized as an innovative and green approach in multiple fields. To expand the applications and enhance the properties of the nanomaterials, their functionalization and engineering are being performed on a massive scale. The functionalization helps to add to the existing useful properties of the nanomaterials, hence broadening the scope of their utilization. A large class of covalent and non-covalent functionalized nanomaterials (FNMs) including carbons, metal oxides, quantum dots, and composites of these materials with other organic or inorganic materials are being synthesized and used for environmental remediation applications including wastewater treatment. This review summarizes recent advances in the synthesis, reporting techniques, and applications of FNMs in adsorptive and photocatalytic removal of pollutants from wastewater. Future prospects are also examined, along with suggestions for attaining massive benefits in the areas of FNMs.

The potential of biochar-photocatalytic nanocomposites for removal of organic micropollutants from wastewater

Biochar (BC)-photocatalyst nanocomposites have emerged as appealing water and wastewater treatment technology. Such nanocomposite materials benefit from the synergistic effect of adsorption and photocatalysis to attain improved removal of pollutants from water and wastewater. Under this review, three BC-based nanocomposite photocatalysts such as BC-TiO₂, BC-ZnO, and BC-spinel ferrites were considered. These nanocomposites acquire intrinsic properties to improve the practical limitations of the pristine BC and photocatalysts. The BC-based nanocomposites attained high photocatalytic activity, mechanical hardness, thermal stability, chemically non-reactive, magnetically permeable, reduced energy band gaps, improved reusability, and simplified recovery. Moreover, BC-based photocatalytic nanocomposites showed reduced recombination rates of the electron-hole pairs which are desirable for photocatalytic applications. However, the surface areas of the composites are usually smaller than that of the BC but higher than those of the pristine photocatalysts. Practically, the performances of the nanocomposites are much superior to those of the corresponding pristine components. This hybrid treatment technology is an emerging field and its industrial application is still at an early stage of the investigation. Therefore, exploring the full potential and practical applications of this technology is highly encouraging. Hence, this review focused on the critical evaluation of the most recent research on the synthesis, characterization, and photocatalytic treatment efficiency of the BC photocatalyst nanocomposites towards emerging pollutants in the aqueous medium. Moreover, the influence of various sources of BC feedstocks and their limitations on adsorption and photodegradation activities are discussed in detail. Finally, concluding remarks and future research directions are given to assist and shape the exploration of BC-based nanocomposite photocatalysts in water treatment.

Fabrication of Novel Agrowaste (Banana and Potato Peels)-Based Biochar/TiO2 Nanocomposite for Adsorption of Cr(VI), Statistical Optimization via RSM Approach

In this research work, a simple, efficient, and eco-friendly procedure for the biosorption of Cr(VI) ions was studied. A detailed comparative study was performed to check the adsorption efficiency of agrowaste (banana and potato peels)-based adsorbents. Firstly, mixed biosorbent was washed, dried and ground into powder, secondly, biosorbent was pyrolyzed into biochar and thirdly TiO2 nanocomposite (TiO2 NC) biosorbent was made by sonicating using prepared biochar and TiO2 NPs. Titanium dioxide nanoparticles (TiO2 NPs) were synthesized by a green method using Psidium guajava leaf extract. The synthesized adsorbents were characterized by SEM, EDX FT-IR, XRD and UV-visible analysis. The effect of four different factors, i.e., pH of the synthetic metallic solution, time, concentration and adsorbent dosage was studied. The optimum conditions were time (120 min), pH (3), concentration (10 ppm) and adsorbent dosage (1.0 g). The kinetic modeling showed that the adsorption of Cr(VI) ion follows a pseudo second-order mechanism and the Langmuir isotherm model was found to fit better for this study. Response surface methodology (RSM)-based optimized parameters provided optimal parameter sets that better represent the adsorption rate models. The uptake capacity of Cr(VI) from aqueous solution was found to be biomass (76.49 mg/L) ˂ biochar (86.51 mg/L) ˂ TiO2 NC (92.89 mg/L). It can be suggested that the produced TiO2 NC could possibly be an efficient biosorbent for the removal of Cr(IV).

A review of microplastic fibres: generation, transport, and vectors for metal(loid)s in terrestrial environments

The laundering of synthetic fabrics has been identified as an important and diffuse source of microplastic (<5 mm) fibre contamination to wastewater systems. Home laundering can release up to 13 million fibres per kg of fabric, which end up in wastewater treatment plants. During treatment, 72-99% of microplastics are retained in the residual sewage sludge, which can contain upwards of 56 000 microplastics per kg. Sewage sludge is commonly disposed of by application to agricultural land as a soil amendment. In some European countries, application rates are up to 91%, representing an important pathway for microplastics to enter the terrestrial environment, which urgently requires quantification. Sewage sludge also often contains elevated concentrations of metals and metalloids, and some studies have quantified metal(loid) sorption onto various microplastics. The sorption of metals and metalloids is strongly influenced by the chemical properties of the sorbate, the solution chemistry, and the physicochemical properties of the microplastics themselves. Plastic-water partition coefficients for the sorption of cadmium, mercury and lead onto microplastics are up to 8, 32, and 217 mL g^-1 respectively. Sorptive capacities of microplastics may increase over time, due to environmental degradation processes increasing the specific surface area and surface density of oxygen-containing functional groups. A range of metal(loid)s, including cadmium, chromium, and zinc, have been shown to readily desorb from microplastics under acidic conditions. Sorbed metal(loid)s may therefore become more bioavailable to soil organisms when the microplastics are ingested, due to the acidic gut conditions facilitating desorption. Polyester (polyethylene terephthalate) should be of particular focus for future research, as few quantitative sorption studies currently exist, it is potentially overlooked from density separation studies due to its high density, and it is by far the most widely used fibre in apparel textiles production.

Removal of endocrine disrupters from the contaminated environment: public health concerns, treatment strategies and future perspectives - A review

Endocrine-disrupting compounds (EDCs) are emerging contaminants of concern (ECC) that disturb endocrine hormones and system functionality even at very low concentrations (i.e. μg/L or ng/L levels). Hence, EDCs are found in all components of the environment including surface and groundwater, wastewater, soil, outdoor and indoor air and in the contaminated foods from a variety of sources (run off from agricultural activities, sewage treatment plants, leakage from septic tanks etc.), and the effects are more severe as the majority of EDCs do not have standard regulations. The environmental mobility of EDCs is higher as conventional wastewater treatment does not degrade efficiently and the development of effective and sustainable removal technologies specifically designed for the removal of those emerging micropollutants is essential. Accordingly, EDCs cause various public health diseases such as reproductive abnormalities, obesity, various cancer types, cardiovascular risks, metabolic disorders, epigenetic alterations, autism, etc. This paper reviews the existing and emerging treatment technologies for the removal of phenolic based EDCs, such as natural estrogens (estrone (E1), 17β-estradiol (E2), estriol (E3)), synthetic estrogen 17α-ethinylestradiol (EE2) and phenolic xenoestrogens (4-nonyl phenols (4-NP) and bisphenol-A (BPA)) from the contaminated environment. These includes advanced oxidation processes (AOP), adsorption processes, membrane based filtration, bioremediation, phytoremediation and other integrated approaches. The sustainability of EDCs removal can be assured through the use of combined processes (i.e. low-cost - biological and adsorption methods with efficient and costly - AOPs) techniques through system integration to achieve better removal efficiency than using a single treatment technique. Besides, the public health concerns and future research perspectives of EDCs are also highlighted.

Pyrolysis processing of PFAS-impacted biosolids, a pilot study

Concentrations of per- and poly-fluoroalkyl substances (PFAS) present in wastewater treatment biosolids are a growing concern. Pyrolysis is a thermal treatment technology for biosolids that can produce a useful biochar product with reduced levels of PFAS and other contaminants. In August 2020, a limited-scope study investigated target PFAS removal of a commercial pyrolysis system processing biosolid with the analysis of 41 target PFAS compounds in biosolids and biochar performed by two independent laboratories. The concentrations of 21 detected target compounds in the input biosolids ranged between approximately 2 µg/kg and 85 µg/kg. No PFAS compounds were detected in the biochar. The PFAS concentrations in the biochar were assumed to equal the compounds' minimum detection limits (MDLs). The pyrolysis system's target PFAS removal efficiencies (REs) were estimated to range between >81.3% and >99.9% (mean >97.4%) with the lowest REs being associated with the lowest detected PFAS concentrations and the highest MDLs. No information on non-target PFAS compounds in influent or effluent media or products of incomplete combustion was considered. Selected gaseous emissions were measured by Fourier transform infrared spectroscopy and gas chromatography time-of-flight mass spectrometry to provide additional information on air emissions after process controls. This limited-scope study indicated that additional research to further understand this process is warranted.Implications: Development of alternative approaches to manage PFAS-impacted biosolids is of emerging international importance. A commercially operating biosolid pyrolysis process was shown to lower target PFAS levels in produced biochar. Additional research is warranted to understand all potential PFAS transformation emission routes and optimal air pollution emissions control strategies for this technology class.

Removal of pharmaceuticals from water using sewage sludge-derived biochar: A review

In recent years, considerable attention has been paid to the beneficial utilization of sewage sludge to reduce the risks associated with sludge disposal. Besides other applications of sludge, biochar produced from sludge has also been employed for the elimination of various pollutants from water. This review critically evaluates the recent progress in applications of sludge-based biochar for the adsorption of pharmaceuticals from water. The synthesis techniques of biochar production from sludge and their effects on physicochemical characteristics of produced biochar are discussed. The removal of various pharmaceuticals by sludge-based biochar are described in detail, with the emphasis on the adsorption mechanism and their reusability potential. It is evident from the literature that sludge-based biochar has demonstrated excellent potential for the adsorption of numerous pharmaceuticals from the aqueous phase. The major hurdles and issues related to the synthesis of sludge-based biochar and applications are highlighted, with reference to the adsorption of pharmaceuticals. Finally, a roadmap is suggested along with future research directions to ensure the sustainable production of biochar from sludge and its applications in water treatment.

Biochar as environmental armour and its diverse role towards protecting soil, water and air

Biochar has been of considerable importance for various environmental applications in recent years. It has exhibited substantial advantages like favourable structural and surface properties, easy process of preparation and widely available feedstocks. These set of exceptional properties make it an efficient, cost-effective and environment friendly source for diversified elimination of pollutants. The heterogeneity of physico-chemical properties offers a possibility for biochar to optimize its efficacy for targeted applications. This review aims to highlight the critical role that biochar plays in various environmental applications, be it in soil, water or air. In particular the article offers a comprehensive review of the recent research findings and updates related to the diversified role of biochar. Also, the interaction of pollutants with biochar functional groups and the impact of variation of parameters on biochar attribute relevant to specific pollutant removal, modifications, mechanisms involved and competence for such removal has been discussed. Different technologies for production of biochar have also been summarized with an emphasis on post treatment of biochar, such as modification and doping. In addition to this, the underlying gaps in the studies carried out so far and recommendations for future research areas in biochar have also been deliberated.

Sewage sludge-derived biochar for the adsorptive removal of wastewater pollutants: A critical review

The production of biochar from sewage sludge pyrolysis is a promising approach to transform the waste resultant from wastewater treatment plants (WWTPs) to a potential adsorbent. The current review provides an up-to-date review regarding important aspects of sewage sludge pyrolysis, highlighting the process that results major solid fraction (biochar), as high-value product. Further, the physio-chemical characteristics of sewage-sludge derived biochar such as the elemental composition, specific surface area, pore size and volume, the functional groups, surface morphology and heavy metal content are discussed. Recent progress on adsorption of metals, emerging pollutants, dyes, nutrients and oil are discussed and the results are examined. The sewage sludge-derived biochar is a promising material that can make significant contributions on pollutants removal from water by adsorption and additional benefit of the management of huge volume of sewage. Considering all these aspects, this field of research still needs more attention from the researchers in the direction of the technological features and sustainability aspects.

Lanthanum hydroxide engineered sewage sludge biochar for efficient phosphate elimination: Mechanism interpretation using physical modelling

In the present study, lanthanum hydroxide (La OH)-engineered sewage sludge biochar (La-SSBC) was utilized for efficient phosphate elimination from an aqueous medium. A high adsorption capacity of 312.55 mg P/g was achieved using La-SSBC at 20 °C, which was an excellent adsorbent performance in comparison to other biochar-based adsorbents. Additionally, the performance of La-SSBC was stable even at wider range of pH level, the existence of abundant active anions, and recycling experiments. Statistical physics modeling with the fitting method based on the Levenberg-Marquardt iterating algorithm, as well as various chemical characterizations, suggested the unique double-layered mechanism of phosphate capturing: one functional group of La-SSBC adsorbent describing a prone direction of the PO₄ ions on the stabilize surface in a multi-ionic process, forming the first layer adsorption. Additionally, SSBC played an important role by releasing positively charged cations in solution, overcoming the electronic repulsion to form a second layer, and achieving excellent adsorption capacity. The calculation of multiple physicochemical parameters including adsorption energy further evidenced the process. This two-layered mechanism sheds light on the complex interaction between phosphate and biochar. Moreover, the management of sewage sludge associated with the requirement of cost-effectively and environmentally acceptable mode. Therefore, the present investigation demonstrated an efficient approach of the simultaneous sewage sludge utilization and phosphate removal.

Novel insights into the adsorption of organic contaminants by biochar: A review

With rising concerns in the practical application of biochar for the remediation of environment influenced by various organic contaminants, a critical review to facilitate insights the crucial role that biochar has played in wastewater and polluted soil decontamination is urgently needed. This research therefore aimed to describe different intriguing dimensions of biochar interactions with organic contaminants, which including: (i) an introduction of biochar preparation and the related physicochemical properties, (ii) an overview of mechanisms and factors controlling the adsorption of organic contaminants onto biochar, and (iii) a summary of the challenges and an outlook of the further research needs in this issue. In the light of the survey consequences, the appearance of biochar indicates the potential in substituting the existing costly adsorbents, and it has been proved that biochar is one promising adsorbent for organic pollutants adsorption removal from water and soil. However, some research gaps, such as dynamic adsorption, potential environmental risks, interactions between biochar and soil microbes, novel modification techniques, need to be further investigated to facilitate its practical application. This research will be conductive to better understanding the adsorption removal of organic contaminants by biochar.

Facile fabrication of robust, versatile, and recyclable biochar-graphene oxide composite monoliths for efficient removal of different contaminants in water

Water pollution produced by various contaminants is presently a major worldwide issue, posing a significant challenge to the development of novel materials for water treatment. Herein, robust and recyclable biochar-graphene oxide (BC-GO) composite monoliths were prepared utilizing lignin precursor as a carbon source in a one-pot hydrothermal process free of hazardous chemicals. Characterization results indicated the BC-GO composite monolith had abundant microchannels, nanopores, and a large specific surface area, thereby exhibiting a high adsorption capacity of 796.8 mg g^-1 to doxycycline in water, which was superior to conventional adsorbents. Furthermore, by annealing the BC-GO composite monolith, it could be transformed to hydrophobic (CA = 140°). The annealed BC-GO composite monolith retained a pronounced porous structure with a larger surface area and showed exceptional absorption capabilities of 55-130 g g^-1 toward various oils and solvents, which were higher/comparable to previously reported graphene-based materials. In addition, both BC-GO composite monoliths were highly stable and could be reused for a number of cycles of pollutants removal. The simplicity, environmental friendliness, and effectiveness of our approach to building BC-GO composite monoliths may pave the way for their future applications in the field of water purification.

A review of pesticides sorption in biochar from maize, rice, and wheat residues: Current status and challenges for soil application

The use of pesticides has been increasing in recent years for maintaining traditional agricultural practices. However, these chemicals are associated with several environmental impacts, demanding urgent remediation techniques. Biochar is a carbonaceous material produced by pyrolysis that has the potential for pesticide sorption and remediation. In this context, this interdisciplinary review systematically assessed the state of the knowledge of crop residues to produce biochar for pesticide sorption. We focused on maize, rice, and wheat residues since these are the three most-produced grains worldwide. Besides, we evaluated different biochar handling, storage, and soil dispersion techniques to ease its implementation in agriculture. In general, pyrolysis temperature influences biochar characteristics and its potential for pesticide sorption. Furthermore, biochar amended soils had greater pesticide sorption capacity, limiting potential leaching and runoff. Most studies showed that the feedstock and specific surface area influence the biochar sorption properties, among other factors. Also, biochar reduces pesticides' bioavailability, decreasing their toxicity to soil organisms and improving soil fertility and crop yields. Nonetheless, the retrieved papers assessed only 21 pesticides, mainly consisting of lab-scale batch experiments. Therefore, there is still a gap in studies evaluating biochar aging, its potential desorption, pesticide co-contaminations, the associated microbiological processes, and field applications. Determining flow properties for biochars of different sizes and pellets is vital for reliable handling equipment design, and performing techno-economic assessment under different farm contexts is encouraged. Ultimately, coupling biochar production with residue management could address this challenge on sustainable agricultural systems.

The effects of biochar/compost for adsorption behaviors of sulfamethoxazole in amended wetland soil

Biochar and compost were two common amendments for the polluted soil. However, few studies were conducted to study the sorption of organic pollutants on combined biochar-compost and the relative adsorption mechanisms in mixed soil. The work had studied the adsorption and desorption behaviors of sulfamethoxazole (SMX) onto wetland soil after amended with biochar and/or compost. Moreover, the physicochemical and morphology properties of biochar/compost and amended soils were analyzed to discuss the relative adsorption mechanisms. Studies showed that the adsorption capacity of amended soils increased with the total amount of biochar or/and compost added, which was positively related to SOM, CEC, and EC of amended soils, but had nothing to do with the type of additives. Compared with the compost-treated treatments, the biochar-treated treatments generally achieved lower desorption rates, which also had demonstrated both different adsorption mechanisms. Pore filling and hydrophobic partitioning were the main adsorption mechanisms for biochar and compost, respectively. Though biochar owned developed pore structure, however, pore-filling of biochar was overwhelmingly weakened due to pore-blocking in mixed soils. Hence, in soil environment, compost is a kind of a more desirable amendment than biochar in absorbing and degrading organic pollutants.

Synthesis and Characterization of Titanium Dioxide Hollow Nanofiber for Photocatalytic Degradation of Methylene Blue Dye

Environmental crisis and water contamination have led to worldwide exploration for advanced technologies for wastewater treatment, and one of them is photocatalytic degradation. A one-dimensional hollow nanofiber with enhanced photocatalytic properties is considered a promising material to be applied in the field. Therefore, we synthesized titanium dioxide hollow nanofibers (THNF) with extended surface area, light-harvesting properties and an anatase–rutile heterojunction via a template synthesis method and followed by a calcination process. The effect of calcination temperature on the formation and properties of THNF were determined and the possible mechanism of THNF formation was proposed. THNF nanofibers produced at 600 °C consisted of a mixture of 24.2% anatase and 75.8% rutile, with a specific surface area of 81.2776 m²/g. The hollow nanofibers also outperformed the other catalysts in terms of photocatalytic degradation of MB dye, at 85.5%. The optimum catalyst loading, dye concentration, pH, and H₂O₂ concentration were determined at 0.75 g/L, 10 ppm, pH 11, and 10 mM, respectively. The highest degradation of methylene blue dye achieved was 95.2% after 4 h of UV irradiation.

Fungi and biochar applications in bioremediation of organic micropollutants from aquatic media

The conventional wastewater treatment system such as bacteria, is not able to remove recalcitrant micropollutants effectively. While, fungi have shown high capacity in degradation of recalcitrant compounds. Biochar, on the other hand, has gained attention in water and wastewater treatment as a low cost and sustainable adsorbent. This paper aims to review the recent applications of three major fungal divisions including Basidiomycota, Ascomycota, and Mucoromycotina, in organic micropollutants removal from wastewater. Moreover, it presents an insight into fungal bioreactors, fungal biofilm and immobilization system. Biochar adsorption capacities for organic micropollutants removal under different operating conditions are summarized. Finally, few recommendations for further research are established in the context of the combination of fungal biofilm with the technologies relying on the adsorption by porous carbonaceous materials.

The evaluation of immobilization behavior and potential ecological risk of heavy metals in bio-char with different alkaline activation

The bio-char was prepared by co-pyrolysis of municipal sewage sludge and biomass with chemical activation. The alkaline activating agents of KOH and K₂CO₃ were used to develop multilevel pore structure without heavy metal. The proximate analysis, ultimate analysis, SEM, and surface area and porosity analyzer were applied to present the physico-chemical properties and multilevel pore structure of bio-char. After impregnation pretreatment, the KOH provided more functional ingredients and reacted with C to expand pore structure for bio-chars. It was confirmed the specific surface area reached 2122.43 m²/g, and micropore area was 1674.85 m²/g after co-pyrolysis at 800 °C. Through the pretreatment of alkaline activation, the novel evaluation of heavy metal immobilization behavior in bio-char matrix were investigated by BCR sequential extraction and leaching tests. The KOH activation showed prominent immobilization behavior relatively, and the K₂CO₃ activation had more noticeable effects on leaching behavior. For Cu, Ni, Cr, Cd, Pb, and Zn, after co-pyrolysis at 900 °C, the proportion of unstable fraction decreased significantly, and the residual fractions of heavy metals were above 89.44% according to BCR sequential extraction procedure. Under optimal pyrolysis temperature, the E_r value of bio-char reduced to 41.93, and the potential ecological risks decreased from considerable risk to low risk to ensure the further eco-friendly application.

The Effect of Biodegradable Waste Pyrolysis Temperatures on Selected Biochar Properties

Biochars produced during biodegradable waste pyrolysis are products with a wide range of environmental applications. The effect of impact biochars depends on their properties which determine the course of specific processes. The main aim of the study was to investigate the effect of pyrolysis temperature on selected properties of biochar produced from various plant wastes (beech wood chips, walnut shells, wheat-rye straw), the valorization of which is of key importance for the implementation of the circular economy. Biochars were produced at temperatures of: 400 °C, 500 °C, 600 °C and 700 °C in a nitrogen atmosphere. An increase in the pyrolysis temperature caused a drop in the biochar production yield. As the temperature increased, higher carbon content and lower hydrogen content could be seen in the products obtained. An increase in the pH and total organic carbon (TOC) values also found. The influence of temperature on ash content, observed in the case of BWS (biochar from walnut shell) and BWRS (biochar from wheat and rye straw), did not occur in the case of BWC (biochar from beech wood chips). Another parameter that demonstrated a growing tendency with increasing temperature was the BET specific surface area (except for biochars from wheat and rye straw). An increase in pyrolysis temperature caused a decrease in the diversity and density of the surface functional groups of biochars. The influence of the type of precursor used in the production of biochar on the presence of surface functional groups was demonstrated. The presence of intense stretching vibrations of C-O bonds, having a potential impact on the sorption capacity of biochars, was determined in the FTIR spectra of BWC600 and BWC700 biochars, this feature, combined with the large BET surface area, may affect the sorption potential of these biochars. The presence of this type of high-intensity vibrations was also observed in the spectra of biochar BWRS600 and BWRS700. This can compensate for the low BET surface value and play an important role when using these biochars in sorption processes for organic and inorganic compounds.

Microplastics in the environment: Occurrence, perils, and eradication

Microplastics (MPs) with sizes < 5 mm are found in various compositions, shapes, morphologies, and textures that are the major sources of environmental pollution. The fraction of MPs in total weight of plastic accumulation around the world is predicted to be 13.2% by 2060. These micron-sized MPs are hazardous to marine species, birds, animals, soil creatures and humans due to their occurrence in air, water, soil, indoor dust and food items. The present review covers discussions on the damaging effects of MPs on the environment and their removal techniques including biodegradation, adsorption, catalytic, photocatalytic degradation, coagulation, filtration and electro-coagulation. The main techniques used to analyze the structural and surface changes such as cracks, holes and erosion post the degradation processes are FTIR and SEM analysis. In addition, reduction in plastic molecular weight by the microbes implies disintegration of MPs. Adsorptive removal by the magnetic adsorbent promises complete elimination while the biodegradable catalysts could remove 70-100% of MPs. Catalytic degradation via advanced oxidation assisted by S O 4 • - or O H • radicals generated by peroxymonosulfate or sodium sulfate are also adequately covered in addition to photocatalysis. The chemical methods such as sol-gel, agglomeration, and coagulation in conjunction with other physical methods are discussed concerning the drinking water/wastewater/sludge treatments. The efficacy, merits and demerits of the currently used removal approaches are reviewed that will be helpful in developing more sophisticated technologies for the complete mitigation of MPs from the environment.

Conversion of sewage sludge into biochar: A potential resource in water and wastewater treatment

Production of biochar from sewage sludge (SS) is consistent with the goal of sustainable resource recovery and promotes a wastewater-based circular economy. Thermochemical conversion of SS to biochar resolves two major issues simultaneously as it minimizes the cost of disposal and acts as a resource to eliminate the toxic contaminants from water and wastewater. The reusability and ready availability of the biochar, irrespective of the season, makes it an economically viable material for wastewater treatment. In this review, explicit insights into the production, modification and usage of SS derived biochar are provided including (i) the production yield, (ii) characteristic features such as physical, chemical, electrochemical and morphological aspects, and (iii) impact on contaminant removal through adsorption, catalytic and electrochemical processes. Particular attention is given to the use of SS derived biochar as an adsorbent for contaminants present in wastewaters, the potential use of biochar as a catalyst and support material in advanced oxidation processes and the use of biochars as an electrode material. The effect of pyrolysis conditions and co-pyrolysis with other materials on biochar properties is explored and insight is provided into the toxicity of biochar components present at different process conditions.

Insight into the key factors in fast adsorption of organic pollutants by hierarchical porous biochar

Low-cost biochar adsorbent owning great potential for environmental remediation faces a bottleneck in application for its unsatisfied adsorption performance. Compared to the efforts on increasing adsorption capacity, improving adsorption speed which is important for treatment efficiency is often neglected. Herein, a hierarchical porous biochar (HPB) derived from shrimp shell was prepared and exhibited good adsorption capacity (Q_m>300 mg/g) and fast adsorptive equilibrium (≤10 min) towards three typical aromatic organics, whose adsorption universality was further proved by two-way ANOVA analysis. Whereafter, model analysis demonstrated that, the adsorptive forms (mono- and multi-layers) on HPB depended on whether the contaminant is charged. Compared to the benzene-ring site of organics, the charged site contributed 5.13 times to adsorption promotion in monolayer but -0.49 times in inhibition for multilayers forms. Simultaneously, functional group sites contributed relatively weak (0.023 to 0.342 times only). Following structural control revealed that, hierarchical pore structure of HPB was the key for the fast adsorption speed, and highly graphitic structure was important for the high adsorption capacity. This study aims to provide an advanced biochar adsorbent, not only in adsorption capacity but also in adsorptive speed, and reveal the relationship between the structure and adsorption performance of biochar.

Immobilization of heavy metals in biochar derived from co-pyrolysis of sewage sludge and calcium sulfate

The effects of calcium sulfate (CaSO₄) dosage (mass ratio of CaSO₄ to sludge), pyrolysis temperature and holding time on speciation distribution of Cr, Pb, Cu, Ni and Zn in biochar derived from co-pyrolysis of sewage sludge and CaSO₄ were investigated. The appropriate CaSO₄ dosages for better immobilization of different heavy metals were 0.075 (Cr), 0.025 (Pb), 0.025 (Cu), 0.025 (Ni), and 0.01(Zn), respectively. The corresponding proportions of heavy metals in stable state (oxidizable and residue fractions) were 96.99%, 89.23%, 99.55%, 87.43%, and 54.33%. The high pyrolysis temperature (750 °C) was conducive to immobilization of Cr, Pb and Zn, while the percentages of Cu and Ni in stable state were higher at low pyrolysis temperature (350 °C). The suitable holding time was 60 min (Cr, Cu) and 15 min (Pb, Ni and Zn), respectively. The characterization of samples showed that suitable pyrolysis temperature and holding time could promote the formation of crystals and spherical or ellipsoidal particles in biochar, and pyrolysis of aliphatic to form more mesopores and macropores, resulting in immobilization of more heavy metals. During co-pyrolysis process, CaSO₄ was easily decomposed and generated CaS, CaO, CaCO₃ and Ca(OH)₂, which were beneficial to the immobilization of heavy metals.

Induced changes of pyrolysis temperature on the physicochemical traits of sewage sludge and on the potential ecological risks

Biochar from sewage sludge is a low-cost sorbent that may be used for several environmental functions. This study evaluates the induced effects of pyrolysis temperature on the physicochemical characteristics of sewage sludge (SS) biochar produced at 350 (SSB₃₅₀), 450 (SSB₄₅₀) and 600 (SSB₆₀₀), based on the metal enrichment index, metal mobility index (MMI), and potential ecological risk index (PERI) of Cd, Cu, Pb, and Zn. Increased pyrolysis temperature reduced the biochar concentration of elements that are lost as volatile compounds (C, N, H, O, and S), while the concentration of stable aromatic carbon, ash, alkalinity, some macro (Ca, Mg, P₂O₅, and K₂O) and micronutrients (Cu and Zn), and toxic elements such as Pb and Cd increased. Increasing the pyrolysis temperature is also important in the transformation of metals from toxic and available forms into more stable potentially available and non-available forms. Based on the individual potential ecological risk index, Cd in the SS and SSB₄₅₀ were in the moderate and considerable contamination ranges, respectively. For all pyrolysis temperature biochar Cd was the highest metal contributor to the PERI. Despite this, the potential ecological risk index of the SS and SSBs was graded as low.

Single and competitive adsorptions of micropollutants using pristine and alkali-modified biochars from spent coffee grounds

This study investigated the single and competitive adsorption characteristics of micropollutants using the pristine and alkali-modified spent coffee grounds (SCG) biochars. The alkali modification substantially improved the physicochemical characteristics of the SCG biochars (specific surface area and pore volume), which may have led to differences in the adsorption behaviors of the micropollutants. The pseudo second order model (R² ≥ 0.990) better described the single and competitive adsorption kinetics than the pseudo first order model (R² ≥ 0.664). It is evident that chemisorption played a key role in the removal of the micropollutants by the pristine and alkali-modified SCG biochars. The single and competitive adsorptions of the micropollutants were highly dependent on the solution pH and ionic strength since the pore-filling effects, electrostatic and hydrophobic interactions governed their removal by the pristine and alkali-modified SCG biochars. The higher removal efficiencies of the micropollutants by the alkali-modified SCG biochars (≥ 44.5%) in the presence of dissolved organic matter compared to the pristine SCG biochars (≤ 18.5%) support the assumption that alkali modification could markedly reinforce the surface structural properties of the SCG biochars related to the adsorption capacities.

Biochar based sorptive remediation of steroidal estrogen contaminated aqueous systems: A critical review

Remediation of steroidal estrogens from aqueous ecosystems is of prevailing concern due to their potential impact on organisms even at trace concentrations. Biochar (BC) is capable of estrogen removal due to its rich porosity and surface functionality. The presented review emphasizes on the adsorption mechanisms, isotherms, kinetics, ionic strength and the effect of matrix components associated with the removal of steroidal estrogens. The dominant sorption mechanisms reported for estrogen were π-π electron donor-acceptor interactions and hydrogen bonding. Natural organic matter and ionic species were seen to influence the hydrophobicity of the estrogen in multiple ways. Zinc activation and magnetization of the BC increased the surface area and surface functionalities leading to high adsorption capacities. The contribution by persistent free radicals and the arene network of BC have promoted the catalytic degradation of adsorbates via electron transfer mechanisms. The presence of surface functional groups and the redox activity of BC facilitates the bacterial degradation of estrogens. The sorptive removal of estrogens from aqueous systems has been minimally reviewed as a part of a collective evaluation of micropollutants. However, to the best of our knowledge, a critique focusing specifically and comprehensively on BC-based removal of steroidal estrogens does not exist. The presented review is a critical assessment of the existing literature on BC based steroidal estrogen adsorption and attempts to converge the scattered knowledge regarding its mechanistic interpretations. Sorption studies using natural water matrices containing residue level concentrations, and dynamic sorption experiments can be identified as future research directions.

Residuals, sludge, and biosolids: Advancements in the field

Advancements in the field of residuals, sludge, and biosolids have been made in 2019. This review outlines the major contributions of researchers that have been published in peer-reviewed journals and conference proceedings throughout 2019 and includes brief summaries from over 125 articles. The review is organized in sections including life cycle and risk assessments; characteristics, quality, and measurement including micropollutants, nanoparticles, pathogens, and metals; sludge treatment technologies including dewatering, digestion, composting, and wetlands; disposal and reuse including adsorbents, land application and agricultural uses, nutrient recovery, and innovative uses; odor and air emissions; and energy issues.

Efficient removal of tetrabromobisphenol A (TBBPA) using sewage sludge-derived biochar: Adsorptive effect and mechanism

Sewerage sludge-derived biochars (SSDBCs) with high adsorption capacity and excellent recyclability were synthesized to remove tetrabromobisphenol A (TBBPA) in aqueous system. Scanning electron microscopy, elemental mapping via energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy were used to characterize the morphology, composition, and microstructures. The maximum adsorption capacity of SSDBCs was about 87.02 mg g^-1 at 303 K and pH 7.5. The Langmuir isotherm demonstrated that the adsorption was mainly homogeneous and chemical processes. The kinetics of TBBPA removal well fitted the second-order dynamic model. Thermodynamic analysis showed that the adsorption was exothermic. The effect of π-π dispersive force and hydrogen bonding was proven as the main adsorption mechanism. Multiple cycle runs experiment revealed the excellent stability of recycled SSDBCs. This work provided a promising method of sludge resourceful treatment using an efficient, economic, cyclic, and convenient material for typical organic contaminant in the environment.