Graphene oxide chemically reduced and functionalized with KOH-PEI for efficient Cr(VI) adsorption and reduction in acidic medium

Microplastic detection and remediation through efficient interfacial solar evaporation for immaculate water production

Freshwater scarcity and microplastics (MPs) pollution are two concerning and intertwined global challenges. In this work, we propose a "one stone kills two birds" strategy by employing an interfacial solar evaporation platform (ISEP) combined with a MPs adsorbent. This strategy aims to produce clean water and simultaneously enhance MPs removal. Unlike traditional predecessors, our ISEP generates condensed water free from MPs contamination. Additionally, the photothermally driven interfacial separation process significantly improves the MPs removal performance. We observed a removal ratio increase of up to 5.5 times compared to previously reported MPs adsorbents. Thus, our rationally-designed ISEP holds promising potential to not only mitigate the existing water scarcity issue but also remediate MPs pollution in natural water environments.

Engineering a sustainable cadmium sulfide/polyethyleneimine-functionalized biochar/chitosan composite for effective chromium adsorption: optimization, co-interfering anions, and mechanisms

A novel eco-friendly adsorbent was fabricated by mixing mushroom-derived cadmium sulfide and polyethyleneimine-functionalized biochar that was fabricated from coffee waste with a chitosan biopolymer. The green-synthesized CdS/PEI-BC/CTS composite was analyzed using several characterization methods to identify its morphological, compositional, and structural characteristics. In addition, the adsorption property of the composite was investigated for hexavalent chromium as a model for anionic heavy metals. The best adsorption conditions to efficiently adsorb Cr(vi) onto CdS/PEI-BC/CTS were scrutinized in the batch mode. The experimental results elucidated that the higher adsorption efficacy for Cr(vi) was 97.89% at pH = 3, Cr(vi) concentration = 50 mg L-1, CdS/PEI-BC/CTS dose = 0.01 g, and temperature = 20 °C. The impact of co-interfering anionic species on Cr(vi) adsorption was identified in simulated wastewater. The recycling property of the CdS/PEI-BC/CTS composite was assessed for ten runs to ensure the applicability of the green composite. The adsorption mechanism and interaction types were proposed on the basis of kinetic and isotherm studies, along with analysis tools. The mechanistic study proposed that the Cr(vi) adsorption onto CdS/PEI-BC/CTS occurred via chemical and physical pathways, including protonation, electrostatic interactions, reduction, and coordination bonds.

Bacterial cellulose microfilament biochar-architectured chitosan/polyethyleneimine beads for enhanced tetracycline and metronidazole adsorption

This study investigates the potential applications of incorporating 2D bacterial cellulose microfibers (BCM) biochar into chitosan/polyethyleneimine beads as a semi-natural sorbent for the efficient removal of tetracycline (TET) and metronidazole (MET) antibiotics. Batch adsorption experiments and characterization techniques evaluate removal performance and synthesized adsorbent properties. The adsorbent eliminated 99.13 % and 90 % of TET and MET at a 10 mg.L-1 concentration with optimal pH values of 8 and 6, respectively, for 90 min. Under optimum conditions and a 400 mg.L-1 concentration, MET and TET have possessed the maximum adsorption capacities of 691.325 and 960.778 mg.g-1, respectively. According to the isothermal analysis, the adsorption of TET fundamentally follows the Temkin (R2 = 0.997), Redlich-Peterson (R2 = 0.996), and Langmuir (R2 = 0.996) models. In contrast, the MET adsorption can be described by the Langmuir (R2 = 0.997), and Toth (R2 = 0.991) models. The pseudo-second-order (R2 = 0.998, 0.992) and Avrami (R2 = 0.999, 0.999) kinetic models were well-fitted with the kinetic results for MET and TET respectively. Diffusion models recommend that pore, liquid-film, and intraparticle diffusion govern the rate of the adsorption process. The developed semi-natural sorbent demonstrated exceptional adsorption capacity over eleven cycles due to its porous bead structure, making it a potential candidate for wastewater remediation.

A highly sensitive electrochemical immunosensor based on rGO-PEI-Ag nanocomposites for the detection of tilmicosin

A label-free electrochemical immunosensor was developed to rapidly detect tilmicosin (TMC) residues in pork and milk. The immunosensor was constructed by immobilizing a high-affinity monoclonal antibody against TMC on an rGO-PEI-Ag nanocomposite-modified electrode. The rGO-PEI-Ag nanocomposites were prepared by mixing polyethyleneimine (PEI) modified reduced graphene oxide (rGO) with AgNO3 solution. The prepared rGO-PEI-Ag nanocomposites showed good redox activity and conductivity, as characterized by ultraviolet-visible spectroscopy (UV-Vis), transmission electron microscopy (TEM), and X-ray diffraction (XRD). During the preparation process, staphylococcal protein A (SPA) was added to targetedly bind the Fc segment of the monoclonal antibody. The immunosensor showed a low detection limit (LOD) of 0.0013 ng/mL, a linear range of 0.01-100 ng/mL, and recoveries ranging from 92.77 to 100.02% in pork and 92.26-101.23% in milk. Furthermore, the immunosensor exhibited good stability, reproducibility, and specificity in detecting TMC in pork and milk real samples.

Simultaneous removal of Cr(Ⅵ) and tetracycline from wastewater by dielectric barrier discharge plasma coupled with TiO2/rGO/Cu2O composites: Performance and mechanism

In this study, dielectric barrier discharge (DBD) plasma combined with titanium dioxide/reduced graphene oxide/copper oxide (TiO2/rGO/Cu2O) composites for simultaneous removal of hexavalent chromium (Cr(Ⅵ)) and tetracycline (TC) from wastewater were explored systematically. The TiO2/rGO/Cu2O composites were successfully prepared to improve the specific surface area and charge carrier separation rate. When Cr(Ⅵ) and TC coexist, the two pollutants have better removal efficiency without changing the initial pH. Moreover, the removal efficiency of Cr(Ⅵ) and TC could be further improved in the DBD-TiO2/rGO/Cu2O system, indicating that the TiO2/rGO/Cu2O composites also exhibited good synergistic effects with the DBD plasma. The mechanism exploration showed that the TiO2/rGO/Cu2O composite catalyst could be activated in DBD system to produce various active species by photocatalytic reaction, among which photo-generated electrons and •O2- could significantly enhance Cr(Ⅵ) reduction, while photo-generated holes and •OH could improve TC degradation. More importantly, the intermediate products obtained from TC degradation can be oxidized to •CO2- by photo-generated holes, which can also facilitate the reduction of Cr(Ⅵ). This study shows that DBD combined with TiO2/rGO/Cu2O composites are capable of simultaneous Cr(Ⅵ) reduction and TC degradation, which would provide novel ideas for practical wastewater remediation.

Using the inherent elements in yeast biomass to produce Ni2P/N-doped biocarbon composites for efficient hexavalent chromium reduction

The heterogeneous catalytic reduction of Cr(VI) to Cr(III) is an effective strategy for aqueous Cr(VI) contamination abatement, which requires the development of highly efficient, low-cost, and recyclable catalysts. Herein, Ni2P/N-doped biocarbon composites (Ni2P/N-BC) were fabricated through an anoxic pyrolysis process using NaCl and KCl as activators. A precursor of yeast biomass provided the essential C, N, and P elements for Ni2P/N-BC formation. When adopted for Cr(VI) reduction in the presence of oxalic acid as a reductant, the fabricated Ni2P/N-BC performed superior catalytic activity with a 100% Cr(VI) reduction efficiency within 10 min (Ni2P/N-BC-5 = 0.2 g L-1, oxalic acid = 0.4 g L-1, Cr(VI) = 20 mg L-1). Typical affecting parameters, e.g., catalyst dosage, oxalic acid loading, reaction temperature, initial solution pH, and water matrix, were investigated. Ni2P/N-BC exhibited good applicability in a broad pH range from 3.0 to 9.0 and in actual aquatic systems. Cr(VI) reduction efficiency remained 92.7% after five recycle runs. Such promising catalytic activity may originate from the well-crystallized Ni2P, N-doped biocarbon framework and high specific surface area of the materials. Preliminary reaction mechanism analysis indicated that the favorable charge state of Ni2P, fast hydrogen transfer, affinity of oxalic acid to Cr(VI), and inherent electron transfer in the biocarbon matrix contributed to effective Cr(VI) reduction. This work not only provides a facile and low-cost strategy to construct Ni2P/N-doped biocarbon nanosheet composite using environmentally benign biomass but also brings new insights for the remediation of Cr(VI) contamination.

Graphene Oxide/Styrene-Butadiene Latex Hybrid Aerogel with Improved Mechanical Properties by PEI Grafted GO and CNT

Graphene oxide aerogel (GOA) has wide application prospects due to its low density and high porosity. However, the poor mechanical properties and unstable structure of GOA have limited its practical applications. In this study, polyethyleneimide (PEI) was used to graft onto the surface of GO and carbon nanotubes (CNTs) to improve compatibility with polymers. Composite GOA was prepared by adding styrene-butadiene latex (SBL) to the modified GO and CNTs. The synergistic effect of PEI and SBL, resulted in an aerogel with excellent mechanical properties, compressive resistance, and structural stability. When the ratio of SBL to GO and GO to CNTs was 2:1 and 7:3, respectively, the obtained aerogel performance was the best, and the maximum compressive stress was 784.35% higher than that of GOA. The graft of PEI on the surface of GO and CNT could improve the mechanical properties of the aerogel, with greater improvements observed with grafting onto the surface of GO. Compared with GO/CNT/SBL aerogel without PEI grafting, the maximum stress of GO/CNT-PEI/SBL aerogel increased by 5.57%, that of GO-PEI/CNT/SBL aerogel increased by 20.25%, and that of GO-PEI/CNT-PEI/SBL aerogel increased by 28.99%. This work not only provided a possibility for the practical application of aerogel, but also steered the research of GOA in a new direction.

A review of novel green adsorbents as a sustainable alternative for the remediation of chromium (VI) from water environments

The presence of heavy metal, chromium (VI), in water environments leads to various diseases in humans, such as cancer, lung tumors, and allergies. This review comparatively examines the use of several adsorbents, such as biosorbents, activated carbon, nanocomposites, and polyaniline (PANI), in terms of the operational parameters (initial chromium (VI) concentration (C_o), temperature (T), pH, contact time (t), and adsorbent dosage) to achieve the Langmuir's maximum adsorption capacity (q_m) for chromium (VI) adsorption. The study finds that the use of biosorbents (fruit bio-composite, fungus, leave, and oak bark char), activated carbons (HCl-treated dry fruit waste, polyethyleneimine (PEI) and potassium hydroxide (KOH) PEI-KOH alkali-treated rice waste-derived biochar, and KOH/hydrochloric acid (HCl) acid/base-treated commercial), iron-based nanocomposites, magnetic manganese-multiwalled carbon nanotubes nanocomposites, copper-based nanocomposites, graphene oxide functionalized amino acid, and PANI functionalized transition metal are effective in achieving high Langmuir's maximum adsorption capacity (q_m) for chromium (VI) adsorption, and that operational parameters such as initial concentration, temperature, pH, contact time, and adsorbent dosage significantly affect the Langmuir's maximum adsorption capacity (q_m). Magnetic graphene oxide functionalized amino acid showed the highest experimental and pseudo-second-order kinetic model equilibrium adsorption capacities. The iron oxide functionalized calcium carbonate (IO@CaCO₃) nanocomposites showed the highest heterogeneous adsorption capacity. Additionally, Syzygium cumini bark biosorbent is highly effective in treating tannery industrial wastewater with high levels of chromium (VI).

Chemical doping of unsubstituted perylene diimide to create radical anions with enhanced stability and tunable photothermal conversion efficiency

N-doping of perylene diimides (PDIs) to create stable radical anions is significant for harvesting photothermal energy due to their intensive absorption in the near-infrared (NIR) region and non-fluorescence. In this work, a facile and straightforward method has been developed to control the doping of perylene diimide to create radical anions using organic polymer polyethyleneimine (PEI) as a dopant. It was demonstrated that PEI is an effective polymer-reducing agent for the n-doping of PDI toward the controllable generation of radical anions. In addition to the doping process, PEI could suppress the self-assembly aggregation and improve the stability of PDI radical anions. Tunable NIR photothermal conversion efficiency (maximum 47.9%) was also obtained from the radical-anion-rich PDI-PEI composites. This research provides a new strategy to tune the doping level of unsubstituted semiconductor molecules for varying yields of radical anions, suppressing aggregation, improving stability, and obtaining the highest radical anion-based performance.

Hyperbranched polyethyleneimine-functionalised chitosan aerogel for highly efficient removal of melanoidins from wastewater

Melanoidins are hazardous dark-coloured substances contained in molasses-based distillery wastewater. Adsorption is an effective approach to eliminate melanoidins from wastewater. However, melanoidin adsorption capacities of available adsorbents are unsatisfactory, which seriously limits their practical application. A hyperbranched polyethyleneimine-functionalised chitosan aerogel (HPCA) was fabricated as an effective adsorbent for melanoidin scavenging. HPCA demonstrated superior melanoidin adsorption efficiency because of its high specific surface area, abundant amino functional groups, and high hydrophilicity. Melanoidin removal rate of HPCA was 94.95%, which remained at 91.45% after 5 cycles. Notably, using the Langmuir isothermal model, the maximum melanoidin adsorption capacity of HPCA was determined to be 868.36 mg/g, surpassing those of most of previously reported adsorbents. Toxicity experiments indicated that HPCA can be considered a safe adsorbent with excellent biocompatibility that hardly threatens aquatic organisms. The efficient melanoidin removal of HPCA was attributed to electrostatic attraction, H-bonding, and van der Waals force. However, the adsorption might be predominantly controlled by electrovalent interaction between protonated amino groups of HPCA and carboxyl/carboxylate groups of melanoidins. Two novel models, namely, external diffusion resistance-internal diffusion resistance mixed model and adsorption on active site model, were employed to describe the dynamic mass transfer characteristics of melanoidin adsorption by HPCA.

Enhanced removal of aqueous Cr(VI) by the in situ iron loaded activated carbon through a facile impregnation with Fe(II) and Fe(VI) two step method: Mechanism study

In this study, a novel in situ iron-loaded activated carbon (AFPAC) was prepared by a FeSO₄/K₂FeO₄ impregnation and oxidation combination two-step supported on activated carbon for enhanced removal of Cr(VI) from aqueous solutions. Cr(VI) removal efficiency greatly increased by AFPAC more than 70% than that of fresh activated carbon (AC), which is due to rich iron oxides formed in situ and the synergistic effect between iron oxides and activated carbon. Cr(VI) adsorption behaviors on AFPAC under different water quality parameters were investigated. The maximum monolayer adsorption capacities for Cr(VI) by AFPAC are as high as 26.24 mg/g, 28.65 mg/g, and 32.05 mg/g at 25 °C, 35 °C and 45 °C at pH 4, respectively. Density functional theory (DFT) results showed that the adsorption energy of K₂Cr₂O₇ on the surface of FeOOH was - 2.52 eV, which was greater than that on the surface of bare AC, and more charge transfer occurred during the adsorption of K₂Cr₂O₇ on the surface of FeOOH, greatly promoting the formation of Cr = O-Fe. Cr(VI) removal by AFPAC included electrostatic attraction, redox reaction, coordinate complexation, and co-precipitation. Cr(VI) adsorption process on AFPAC consisted of the three reaction steps: (1) AFPAC was fast protonation and Cr₂O₇^2- would electrostatically attract to the positively charged AFPAC surface. (2) Cr₂O₇^2- was reduced into Cr₂O₃ by the carbons bond to the oxygen functionalities on activated carbon and the redox reaction process of FeSO₄ and K₂FeO₄. (3) The inner-sphere complexes were formed, and adsorbed on AFPAC by iron oxides and then co-precipitation.

Charge modifications of graphene oxide enhance the inhibitory effect on insulin amyloid fibrillation based on electrostatic interactions

Graphene oxide (GO) is a biocompatible nanomaterial that has an inhibitory effect on insulin amyloid fibrillation. In order to enhance the inhibitory effect of GO and explore the rules of electrostatic interactions on the inhibitory effect, carboxyl group, PEI and PEG were coupled to the GO nanoplatelet surface to prepare inhibitors of different surface electrical properties. The effects of surface electrical properties of inhibitors on insulin fibrillation were investigated. The results showed that GO, carboxyl group modified GO (GO-COOH), PEI modified GO (GO-PEI), and PEG modified GO (GO-PEG) inhibited insulin fibrillation in a dose-dependent manner. Compared with GO, positive charge-modified GO-PEI and negative charge-modified GO-COOH enhanced the inhibitory effect, while uncharged polymer-modified GO-PEG weakened the inhibitory effect. The inhibitory effect of the inhibitors increased with the increase of surface charge density. The difference in inhibitory effect between GO-PEI and GO-COOH was due to the different electrostatic interactions between inhibitors and insulin, and the different inhibition mechanisms. In addition, inhibitors mainly interact with insulin during the nucleation phase to hinder insulin fibrillation. The charge modifications of graphene oxide enhanced the inhibitory effect on insulin fibrillation based on electrostatic interactions, which will provide new thoughts for the development of anti-amyloid fibrillation drugs.

Graphene-Based Adsorbents for Arsenic, Fluoride, and Chromium Adsorption: Synthesis Methods Review

Water contamination around the world is an increasing problem due to the presence of contaminants such as arsenic, fluoride, and chromium. The presence of such contaminants is related to either natural or anthropogenic processes. The above-mentioned problem has motivated the search for strategies to explore and develop technologies to remove these contaminants in water. Adsorption is a common process employed for such proposals due to its versatility, high adsorption capacity, and lower cost. In particular, graphene oxide is a material that is of special interest due to its physical and chemical properties such as surface area, porosity, pore size as well as removal efficiency for several contaminants. This review shows the advances, development, and perspectives of materials based on GO employed for the adsorption of contaminants such as arsenite, arsenate, fluoride, and hexavalent chromium. We provided a detailed discussion of the synthesis techniques and their relationship with the adsorption capacities and other physical properties as well as pH ranges employed to remove the contaminants. It is concluded that the adsorption capacity is not proportional to the surface area in all the cases; instead, the synthesis method, as well as the functional groups, play an important role. In particular, the sol-gel synthesis method shows better adsorption capacities.

Electrochemical reduction of Cr (VI) using a palladium/graphene modified stainless steel electrode

In this study, a palladium/graphene modified stainless steel electrode was successfully prepared and applied in an electrochemical reduction device to remove Cr (VI) from the wastewater. Pd was modified onto the electrode mainly via interacting with the carboxyl group of graphene. The Cr (VI) removal efficiency was up to 99.70 ± 0.00% under the optimal condition (Pd content proportion of 3%, electrode potential of -0.9 V, pH = 2 and electrolyte concentration of 6 g/L). It was found that Cr (VI) was removed via the following processes: (1) direct electrochemical reduction by accepting electrons, (2) indirect electrochemical reduction by H₂O₂ that was generated from H₂ in the presence of Pd, (3) adsorption through hydrogen bond, and (4) chemical reduction through alkoxy groups donating electrons. The indirect electrochemical reduction considerably promoted the Cr (VI) removal while a small amount of Cr (VI) was removed via adsorption and chemical reduction. The method could not only be used as a pretreatment technology to solve the problem of excessive Cr (VI) concentration of industrial wastewater, but also could provide reference for the electrochemical reduction of similar metal ions.

Scavenging of hexavalent chromium from aqueous solution by Macadamia nutshell biomass modified with diethylenetriamine and maleic anhydride

Based on the premise that aqueous anions of hexavalent chromium (Cr(VI)) are capable of electrostatic interaction with cationic and polar active sites, acid-washed Madacamia nutshell biomass was sequentially treated with diethylenetriamine (DETA) and maleic anhydride (MA) to graft poly(diethylenetriamine-co-maleic anhydride). By displaying a new peak at 1685 cm^-1 ascribed to amide CO stretching vibrations, Fourier transform infrared spectroscopy highlighted the formation of amide groups through reaction of DETA with carboxyl groups on the biomass surface. Scanning electron microscopic images of the MA-modified biomass displayed polymeric growths attributed to copolymerization of DETA with MA. The polar and ionizable amide and amine groups of the grafted copolymer endowed the adsorbent with Cr(VI) removal capabilities over a wide pH range demonstrated by removal efficiencies between 70.9% and 81.7% in the pH 1.6 to pH 10.0 range for the treatment of 20 mL solutions containing 100 mg L^-1 Cr(VI) with 200 mg of adsorbent. Conformity of the adsorption isotherm data to the Freundlich model revealed the heterogeneous nature of the adsorbent surface, which comprised a variety of functional groups capable of interaction with Cr(VI) species in solution. The Sips isotherm model provided the best fit to the equilibrium experimental data, and the adsorption capacity was 779.1 mg g^-1 at pH 1.6, room temperature and an adsorbent dosage of 5.0 g L^-1. The findings indicate that Cr(VI) adsorption onto diethylenetriamine and maleic anhydride modified Madacamia nutshell biomass is a promising option for Cr(VI) removal from aqueous solutions.

Photoreduction of Cr(VI) in wastewater by anodic nanoporous Nb2O5 formed at high anodizing voltage and electrolyte temperature

In this study, nanoporous anodic film was produced by anodization of niobium, Nb in a fluoride ethylene glycol electrolyte. The effect of anodization voltage and electrolyte temperature was studied to find an optimum condition for circular, ordered, and uniform pore formation. The diameter of the pores was found to be larger when the applied voltage was increased from 20 to 80 V. The as-anodized porous film was also observed to comprise of nanocrystallites which formed due to high field-induced crystallization. The nanocrystallites grew into orthorhombic Nb₂O₅ after post-annealing treatment. The Cr(VI) photoreduction property of both the as-anodized and annealed Nb₂O₅ samples obtained using an optimized condition (anodization voltage: 60 V, electrolyte temperature: 70 °C) was compared. Interestingly, the as-anodized Nb₂O₅ film was found to display better photoreduction of Cr(VI) than annealed Nb₂O_5. However, in terms of stability, the annealed Nb₂O₅ presented high photocatalytic efficiency for each cycle whereas the as-anodized Nb₂O₅ showed degradation in photocatalytic performance when used continually.

Adsorption-reduction of Cr(VI) onto unmodified and phytic acid-modified carob waste: Kinetic and isotherm modeling

Carob waste (CW) is an agro-biomass material abundant in nature with potential use for eco-friendly remediation. However, like many biomass-based adsorbents, it suffers from its low adsorption capacity for organic/inorganic pollutants. Therefore, modification using physical and/or chemical means is commonly applied to improve the adsorptive properties of biomass-based adsorbents. In this study, carob waste (CW) and carob waste functionalized with phytic acid (PA-CW), as an ecofriendly product, were applied for the first time for Cr(VI) elimination. Various methods were applied for the material characterization like Fourier-transform infrared spectroscopy, powder X-ray diffraction (PXRD), thermogravimetric analysis (TGA and DTG), X-ray photoelectron spectroscopy (XPS), specific surface area and porosity measurements. The results proved that both CW and PA-CW own appropriate features for efficient adsorption. Bach experiments revealed that the optimum parameters for Cr(VI) (100 mg/mL) removal at 25 °C were pH 2, 0.05 and 0.025 g as adsorbent dose for CW and PA-CW, respectively, over 120 min contact time. The kinetic of adsorption was well-described by the pseudo-second order model, whereas the isotherm modeling fitted well the modified Langmuir model. CW and PA-CW achieved respectively maximum adsorption capacities of 212.4 and 387.9 mg/g, which are among the highest values so far reported for biomass-based adsorbent materials. These results confirmed that CW and PA-CW could be alternative cost-effective adsorbents even for high concentrations of Cr(VI) in industrial wastewaters along with their reduction capacity.

Hexavalent chromium removal from aqueous solutions using biogenic iron nanoparticles: Kinetics and equilibrium study

Green mediated biosynthesis of iron oxide nanoparticles utilising Rosa indica flower petal extracts (RIFP-FeONPs) was used in this investigation. The RIFP-FeONPs were evaluated by the UV-Visible Spectroscopy, FTIR, SEM, EDX, XRD, Zeta potentials, and DLS, and been engaged than for the elimination of Cr (VI) from the contaminated environments. At 269 nm, the RIFP-FeONPs surface plasmon vibration bands were observed, which attributed to the Fe³⁺. XRD patterns of RIFP-FeONPs depicted the intense diffraction peak of face-centered cubic (fcc) iron at a 2θ value of 45.33° from the (311) lattice plane indisputably revealed that the particles are constituted of pure iron. The fabricated nanomaterials are spherical and polydisperse with a diameter of 70-120 nm, and various agglomeration clusters are attributable to intermolecular interaction. Zeta potential measurement and particle size distribution of RIFP-FeONPs showed a mean average size of 115.5 ± 29 nm and a polydispersity index (PDI) of 0.420. The study aims to analyse the appropriateness of RIFP-FeONPs for removing hexavalent chromium from the aqueous environment and the application of adsorption isotherm and statistical models in the experiment. The sorption of Cr (VI) on RIFP-FeONPs was observed to fit well with the isothermal models (R² = 0.98). The linear correlation between processing parameters and time demonstrated that the adsorption efficiency of Cr (VI) well correlated with the pseudo-first order kinetic model and isothermal adsorption with the Langmuir and Freundlich isothermal models, so that the RIFP-FeONPs could be a prospective nanosorbent for hexavalent chromium removal from industrial waste.

Highly efficient Cr(VI) remediation by cationic functionalized nanocellulose beads

Applications of nanocellulose as a water treatment material are being actively pursued based on its interesting properties, such as renewability, large specific surface area, hydrophilic surface chemistry, and biodegradability. This study used carboxymethyl cellulose nanofibrils (CMCNFs) to prepare a typical bead-type adsorbent with improved structural stability as an actual water treatment restoration material. In addition, a cationized nanocellulose adsorbent was prepared by introducing polyethyleneimine (PEI) on the surface of the CMCNF (P/CMCNF), the removal efficiency of Cr(VI) was evaluated, and its mechanism was elucidated. As a result, the P/CMCNF beads showed an excellent Cr(VI) removal capacity of 1302.3 mg/g, the best result among cellulose-based adsorption materials. Cr(VI) was effectively removed by electrostatic attractions combined with chemical reduction and chelation mechanisms. Furthermore, the macrobead fabrication and PEI surface modification process improved the underwater stability of the P/CMCNF, and it showed excellent reuse efficiency.

Bimetallic FeNi nanoparticles immobilized by biomass-derived hierarchically porous carbon for efficient removal of Cr(VI) from aqueous solution

Nano zero-valent iron (nZVI) is an effective material for Cr(VI) treatment, however excessive agglomeration and surface oxidation limit its application. Herein, straw derived hierarchically porous carbon supported FeNi bimetallic nanoparticles (FeNi@HPC) was prepared for effective removal of Cr(VI) from water. FeNi nanoparticles were successfully loaded onto HPC with good dispersibility, and HPC caused an increase in specific surface area of FeNi nanoparticles. FeNi@HPC exhibited a significantly enhanced removal efficiency for Cr(VI) in comparison to Fe@HPC and FeNi NPs. The Ni doping content was further optimized, and the best Ni content in bimetallic NPs was estimated as 10 wt%. The conditions optimal for the activity of FeNi@HPC were assessed, and the highest removal efficiency equivalent to 30 mg L^-1 of Cr(VI) was achieved at pH= 4.0 in 360 min with a dosage of 0.5 g L^-1. Higher temperatures favored the removal of Cr(VI) and FeNi@HPC manifested the lowest activation energy as compared to Fe@HPC and FeNi NPs. The action mechanisms of FeNi@HPC presumably involved electron transfer from Fe⁰, Fe²⁺and atomic hydrogen. This work not only provide a cost-effective and available HPC material to stabilize nZVI but also revealed that using FeNi@HPC is a promising approach for the remediation of water pollution.

Efficient detoxification of Cr(VI)-containing effluents by sequential adsorption and reduction using a novel cysteine-doped PANi@faujasite composite: Experimental study supported by advanced statistical physics prediction

Nowadays, the global spreading of hazardous heavy metals becomes a top-priority environmental challenge, owing to its serious detrimental health outcomes. Herein, a novel cysteine-doped polyaniline@faujasite hybrid composite (Cys-PANi@FAU-50) was synthesized via a facile in-situ polymerization route for the effective detoxification of Cr(VI)-bearing wastewaters. The Cys-PANi@FAU-50 composite displayed an open mesoporous structure richly decorated with nitrogen/oxygen-containing functional groups, which consequently boosted the diffusion, adsorption and reduction of Cr(VI) oxyanions. The Cr(VI) adsorption behavior was satisfactorily tailored via pseudo-second-order law and Langmuir model with a maximum uptake capacity of 384.6 mg/g. Based on the advanced statistical physics theory, the monolayer model with two distinct receptor sites provided a reliable microscopic and macroscopic prediction of the Cr(VI) adsorption process. Stereographically, the Cr(VI) ions were adsorbed through horizontal multi-anchorage and vertical multi-molecular mechanisms on the amine and hydroxyl groups of Cys-PANi@FAU-50, respectively. The thermodynamic functions evidenced that the Cr(VI) adsorption was an endothermic spontaneous process. XPS analysis proved that Cr(VI) ions were electrostatically adsorbed, and subsequently reduced to Cr(III), which were in turn immobilized by chelation with imine/sulfonate groups and electrostatic interactions with carboxylate groups. The Cys-PANi@FAU-50 featured an effortless regenerability and good reusability. Overall, the Cys-PANi@FAU-50 composite owns outstanding potentiality for detoxifying Cr(VI)-laden effluents.

Polydopamine-assisted polyethylenimine grafting melamine foam and the application in wastewater purification

Melamine foam (MF) is a widely used commercial product and exhibits wide applications in many fields ranging from building, transportation to daily chemical product. Recent researches confirm that the special three-dimensional (3D) framework structure of MF can be an ideal substrate to prepare functional materials. In this work, the water-soluble polyethylenimine (PEI) was grafted onto the framework of MF to develop the water purification material toward heavy metal ions removal. The grafting of PEI on MF was achieved with the aids of polydopamine (PDA) coating and epoxy chloropropane (ECH) cross-linking successively. The 3D framework of MF could be well reserved and PEI was homogeneously grafted onto the framework surface. The adsorption capacity of the adsorbent was dependent upon the molecular wight of PEI. Lower PEI molecular weight endowed the adsorbent with better adsorption ability. The maximum adsorption capacity reached 328.95 mg/g, and the adsorbent exhibited extremely high adsorption stability with increasing cycling measurement numbers. Further results showed that the adsorbent also exhibited high reduction ability and induced about 62.5% toxic Cr(VI) to be reduced. This work confirms that the PEI-modified MF sample is a promising adsorbent in the removal of heavy metal ions and it can be used in wastewater treatment.

Insight into the performance and mechanism of persimmon tannin functionalized waste paper for U(VI) and Cr(VI) removal

Herein, using dialdehyde waste paper (DAWP) as a cross-linking agent to immobilize persimmon tannin (PT) was first used to remove the U(VI) and Cr(VI) via the "waste control by waste" concept. The microscopic and macroscopic surface properties of the as-prepared adsorbent was characterized by the advanced characterization techniques. Factors that affected the elimination process such as variable pH, coexistence ions and equilibrium time were investigated by batch techniques. The results showed that the maximal removal capacities of U(VI) and Cr(VI) on DAWP-PT were 242.3 mg/g (pH = 6.0) and 178.7 mg/g (pH = 2.0) at 298 K, which exhibited competitiveness with most of the reported solid materials. Meanwhile, adsorption data were fitted perfectly to the Langmuir and Pseudo-second-order equations, which indicated that the monolayer and homogenous chemisorption dominated the removal process. The SEM-EDX, DFT and XPS analysis conformed that adsorption of U(VI) was mainly via surface complexation, while the elimination of Cr(VI) was a redox reaction process, and about 65.33% of Cr(III) and 34.67% of Cr(VI) co-existed onto the surface of DAWP-PT. Thus, this study would provide a high-efficiency and low-cost adsorbent for radionuclide and heavy metal treatment.

Sustainable removal of Cr(VI) using graphene oxide-zinc oxide nanohybrid: Adsorption kinetics, isotherms and thermodynamics

Metal-based adsorbents are limited for hexavalent chromium [Cr(VI)] adsorption from aqueous solutions because of their low adsorption capacities and slow adsorption kinetics. In the present study, decorated zinc oxide (ZnO) nanoparticles (NPs) on graphene oxide (GO) nanoparticles were synthesized via the solvothermal process. The deposition of ZnO NPs on graphene oxide for the nanohybrid (ZnO-GO) improves Cr(VI) mobility in the nanocomposite or nanohybrid, thereby improving the Cr(VI) adsorption kinetics and removal capacity. Surface deposition of ZnO on graphene oxide was characterized through Fourie Transform Infra-red (FTIR), UV-Visible, X-ray Diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), Energy Dispersive Spectroscopy (EDS), and Brunauer-Emmett-Teller (BET) techniques. These characterizations suggest the formation of ZnO-GO nanocomposite with a specific area of 32.95 m²/g and pore volume of 0.058 cm²/g. Batch adsorption analysis was carried to evaluate the influence of operational parameters, equilibrium isotherm, adsorption kinetics and thermodynamics. The removal efficiency of Cr(VI) increases with increasing time and adsorbent dosage. FTIR, FESEM and BET analysis before and after the adsorption studies suggest the obvious changes in the surface functionalization and morphology of the ZnO-GO nanocomposites. The removal efficiency increases from high-acidic to neutral pH and continues to decrease under alkaline conditions as well. Mathematical modeling validates that the adsorption follows Langmuir isotherm and fits well with the pseudo 2nd order kinetics (Type 5) model, indicating a homogeneous adsorption process. The thermodynamics study reveals that Cr(VI) adsorption on ZnO-GO is spontaneous, endothermic, and entropy-driven. A negative value of Gibb's Free Energy represents the thermodynamic spontaneity and feasibility of the sorption process. To the best of our knowledge, this is the first study of Cr(VI) removal from aqueous solution using this hybrid nanocomposite at near-neutral pH. The synthesized nanocomposites prove to be excellent candidates for Cr(VI) removal from water bodies and natural wastewater systems.

An Electrochemical Immunosensor Based on SPA and rGO-PEI-Ag-Nf for the Detection of Arsanilic Acid

A sensitive electrochemical immunosensor was prepared for rapid detection of ASA based on arsanilic acid (ASA) monoclonal antibody with high affinity. In the preparation of nanomaterials, polyethyleneimine (PEI) improved the stability of the solution and acted as a reducing agent to generate reduced graphene oxide (rGO) with relatively strong conductivity, thereby promoting the transfer of electrons. The dual conductivity of rGO and silver nanoparticles (AgNPs) improved the sensitivity of the sensor. The synthesis of nanomaterials were confirmed by UV-Vis spectroscopy, X-ray diffraction, transmission electron microscopy and scanning electron microscopy. In the optimal experiment conditions, the sensor could achieve the detection range of 0.50–500 ng mL⁻¹ and the limit of detection (LOD) of 0.38 ng mL⁻¹ (S/N = 3). Moreover, the sensor exhibited excellent specificity and acceptable stability, suggesting that the proposed sensor possessed a good potential in ASA detection. Thus, the as-prepared biosensor may be a potential way for detecting other antibiotics in meat and animal-derived foods.

Simultaneous photocatalytic Cr(VI) reduction and phenol degradation over copper sulphide-reduced graphene oxide nanocomposite under visible light irradiation: Performance and reaction mechanism

The contamination of water by synthetic organic molecules and trace metals is a growing challenge, in spite of the enormous research efforts being made in the field of water treatment. In this study, reduced graphene oxide-copper sulphide (rGO-CuS) nanocomposites of different rGO/CuS (2/1, 1/1, 1/2) molar ratios were fabricated via a facile one-step hydrothermal method. The nanocomposite materials, named hereafter as 2rGO-CuS, rGO-CuS and rGO-2CuS, were characterized using various analytical techniques, including X-ray diffraction (XRD), Raman spectroscopy, transmission electron microscopy (TEM), energy dispersive X-ray (EDX) spectroscopy, X-ray photoelectron spectroscopy (XPS) and UV-visible spectrophotometry. The photocatalytic performance of the nanocomposites was assessed under visible light irradiation (λ > 420 nm) for the simultaneous photocatalytic reduction of Cr(VI) and phenol degradation. It was found that rGO-2CuS achieved a remarkable enhancement of the photocatalytic activity among the prepared nanocomposites for the degradation of phenol and reduction of Cr(VI). Therefore, the simultaneous photocatalytic phenol degradation and Cr(VI) reduction over rGO-2CuS sample was further investigated. The experimental results revealed that rGO-2CuS catalyst maintained good degradation efficacy of mixed pollutants after 6 runs and dissolved oxygen was found to be essential to promote Cr(VI) reduction and phenol degradation. A detailed photocatalytic activity under visible light irradiation mechanism was proposed based on quenching experiments and fluorescence measurements.

Facile synthesis and characterization of a novel 1,2,4,5-benzene tetracarboxylic acid doped polyaniline@zinc phosphate nanocomposite for highly efficient removal of hazardous hexavalent chromium ions from water

The present study describes the preparation of a novel 1,2,4,5-benzene tetracarboxylic acid doped polyaniline@zinc phosphate (BTCA-PANI@ZnP) nanocomposite via a facile two-step procedure. Thereafter, the as-prepared composite material adsorption characteristics for Cr(VI) ions removal were evaluated under batch adsorption. Kinetic approach studies for Cr(VI) removal, clearly demonstrated that the results of the adsorption process followed the pseudo second order and Langmuir models. The thermodynamic study indicated a spontaneous and endothermic process. Furthermore, higher monolayer adsorption was determined to be 933.88 mg g^-1. In addition, the capability study regarding Cr(VI) ions adsorption over BTCA-PANI@ZnP nanocomposite clearly revealed that our method is suitable for large scale application. X-ray photoelectron spectroscopy (XPS) analysis confirmed Cr(VI) adsorption on the BTCA-PANI@ZnP surface, followed by its subsequent reduction to Cr(III). Thus, the occurrence of external mass transfer, electrostatic attraction and reduction phenomenon were considered as main mechanistic pathways of Cr(VI) ions removal. The superior adsorption performance of the material, the multi-dimensional characteristics of the surface and the involvement of multiple removal mechanisms clearly demonstrated the potential applicability of the BTCA-PANI@ZnP material as an effective alternative for the removal of Cr(VI) ions from wastewater.