Uptake of micropollutant-bisphenol A, methylene blue and neutral red onto a novel bagasse-β-cyclodextrin polymer by adsorption process

Mesoporous magnetic biochar derived from common reed (Phragmites australis) for rapid and efficient removal of methylene blue from aqueous media

A novel mesoporous magnetic biochar (MBC) was prepared, using a randomly growing plant, i.e., common reed, as an exporter of carbon, and applied for removal of methylene blue (MB) from aqueous solutions. The prepared sorbent was characterized by nitrogen adsorption/desorption isotherm, saturation magnetization, pH of point of zero charges (pHPZC), Fourier-transform infrared spectroscopy (FT-IR), and scanning electron microscopy (SEM). The obtained MBC has a specific surface area of 94.2 m2 g-1 and a pore radius of 4.1 nm, a pore volume of 0.252 cm3 g-1, a saturation magnetization of 0.786 emu g-1, and a pHPZC of 6.2. Batch adsorption experiments were used to study the impact of the physicochemical factors involved in the adsorption process. The findings revealed that MB removal by MBC was achieved optimally at pH 8.0, sorbent dosage of 1.0 g L-1, and contact time of 30 min. At these conditions, the maximum adsorption was 353.4 mg g-1. Furthermore, the adsorption isotherm indicated that the Langmuir pattern matched well with the experimental data, compared to the Freindlich model. The ∆G was - 6.7, - 7.1, and - 7.5 kJ mol-1, at 298, 308, and 318 K, respectively, indicating a spontaneous process. The values of ∆H and ∆S were 5.71 kJ mol-1 and 41.6 J mol-1 K-1, respectively, suggesting endothermic and the interaction between MB and MBC is van der Waals type. The absorbent was regenerated and reused for four cycles after elution with 0.1 mol L-1 of HCl. This study concluded that the magnetic biochar generated from common reed has tremendous promise in the practical use of removing MB from wastewater.

Porous activated carbons derived from waste Moroccan pine cones for high-performance adsorption of bisphenol A from water

Porous-activated carbons (ACs) derived from Moroccan pine cones (PC) were synthesised by a two step-chemical activation/carbonisation method using phosphoric acid (PC-H) and zinc chloride (PC-Z) as activating agents and used for the adsorption of bisphenol A (BPA) from water. Several techniques (TGA/DTA, FT-IR, XRD, SEM and BET) were used to determine the surface area and pore characterisation and variations during the preparation of the adsorbents. The modification significantly increased the surface area of both ACs, resulting in values of 1369.03 m2 g-1 and 1018.86 m2 g-1 for PC-H and PC-Z, respectively. Subsequent adsorption tests were carried out, varying parameters including adsorbent dosage, pH, initial BPA concentration, and contact time. Therefore, the highest adsorption capacity was observed when the BPA molecules were in their neutral form. High pH values were found to be unfavourable for the removal of bisphenol A from water. The results showed that BPA adsorption kinetics and isotherms followed pseudo-second-order and Langmuir models. Thermodynamic studies indicated that the adsorption was spontaneous and endothermic. Besides, the regeneration of spent adsorbents demonstrated their reusability. The adsorption mechanisms can be attributed to physical adsorption, hydrogen bonds, electrostatic forces, hydrophobic interactions, and π-π intermolecular forces.

Adsorption of cationic/anionic dyes and endocrine disruptors by yeast/cyclodextrin polymer composites

Factory and natural wastewaters contain a wide range of organic pollutants. Therefore, multifunctional adsorbents must be developed that can purify wastewater. Phytic acid-cross-linked Baker's yeast cyclodextrin polymer composites (IBY-PA-CDP) were prepared using a one-pot method. IBY-PA-CDP was used to adsorb methylene blue (MB), bisphenol A (BPA), and methyl orange (MO). Studies on the ionic strength and strongly acidic ion salts confirmed that IBY-PA-CDP adsorbs MO through hydrophobic interactions. This also shows that Na+ was the direct cause of the increased MO removal. Adsorption studies on binary systems showed that MB/MO inhibited the adsorption of BPA by IBY-PA-CDP. The presence of MB increased the removal rate of MO by IBY-PA-CDP due to the bridging effect. The Langmuir isotherm model calculated the maximum adsorption capacities for MB and BPA to be 630.96 and 83.31 mg g-1, respectively. However, the Freundlich model is more suitable for fitting the experimental data for MO adsorption. To understand the rate-limiting stage of adsorption, a mass-transfer mechanism model was employed. The fitting results show that adsorption onto the active sites is the rate-determining step. After five regeneration cycles, IBY-PA-CDP could be reused with good stability and recyclability.

Evaluation of hydrochar from peach stones for caffeine removal from aqueous medium and treatment of a synthetic mixture

The presence of micropollutants, such as caffeine (CAF), has been detected throughout the world, since conventional treatment plants are not able to properly degrade them. CAF is a widely consumed stimulant, and has been demanding the development of efficient methodologies for its removal. Aiming at the agriculture waste valorization, a new hydrochar was developed based on chemical and thermal modification of peach stones (mod-PS) for CAF removal from water and from a synthetic mixture. The morphology, functional groups and surface electrical charge of the adsorbent were characterized by SEM, FTIR and zeta potential, respectively. Regarding CAF adsorption performance, the equilibrium time was reached at 480 min and the pseudo-second-order model presented the best fit for the experimental data. The maximum adsorption capacity was 68.39 mg g-1 (298 K) and the Langmuir model exhibited a better fit for the isothermal data. The thermodynamic properties confirmed that the process was exothermic, spontaneous and reversible. The main adsorption mechanisms were hydrogen bonds and π-interactions. The global removal efficiency was satisfactory in the synthetic mixture simulating real wastewater (67%). Therefore, the proposed new hydrochar has potential application as a low-cost adsorbent for CAF removal.

Citric acid cross-linked β-cyclodextrins: A review of preparation and environmental/biomedical application

The β-cyclodextrins (β-CD) are biocompatible macrocyclic candidates for the preparation of various composites with enhanced functions. While nontoxic and biodegradable citric acid (CA) is the favorite crosslinking agent for fabricating hierarchical advanced structures. The carboxyl and hydroxyl groups on CA can serve as "structural bridges" and enhance the solubility of β-CD. Leading to the construction of CA cross-linked β-CD with marvelous complicated structures and targeted functions. Here, we directly categorized the grafted composite materials into two main types such as organic and inorganic materials. Particularly, some representative composite materials are listed and analyzed in detail according to their preparation, advantages of unique characteristics, as well as the possible applications in environmental and biomedical fields such as adsorption of pollutants, sensors, and biomedical applications.

Removal of methylene blue by acrylic polymer adsorbents loaded with magnetic iron manganese oxides: Synthesis, characterization, and adsorption mechanisms

Dyes pose significant risks for aquatic environments and biological health in general owing to their non-biodegradable nature, carcinogenicity, and toxicity. The effective treatment of dye wastewater has become an important research topic. In this study, acrylic polymers (AP) loaded with magnetic iron manganese oxides (MIMO) (AP/MIMO) were prepared and used for the first time for the adsorption of methylene blue (MB). Carbon in AP/MIMO exists predominantly in the C-H and C-C forms, with its content reaching 50.7%. Oxygen and nitrogen in AP/MIMO exist mainly in the -CO- and -N-C forms, with contents of up to 41.5% and 73.3%, respectively. MB removal by AP/MIMO was consistent with the pseudo-second-order kinetic model (R2 = 0.99), equilibrium was achieved within 20 min, and the highest MB capacity of 2611.23 mg g-1 was predicted by the Langmuir isotherm model (R2 = 0.91-0.94). AP/MIMO exhibited excellent MB adsorption performance in the pH range of 4-10, with a removal efficiency higher than 99.0% (MB = 100 mL 1000 mg L-1; AP/MIMO = 50 mg). Thermodynamic indicators, such as positive entropy (ΔS0; 98.30 J⋅mol-1⋅K-1), negative Gibbs free energy (ΔG0; -29.40, -28.50, and -27.50 KJ⋅mol-1), and positive enthalpy (ΔH0; 2.30 KJ⋅mol-1), demonstrated that MB removal by AP/MIMO was autonomous, favorable, and endothermic. In addition, the integration of experimental results and theoretical calculations verified that electrostatic interactions were the primary mechanism for MB adsorption at carboxyl sites on AP/MIMO. The total interaction energy between AP and MB was -310.43 kJ⋅mol-1, and the electrostatic effect had a decisive contribution to the MB adsorption, with a value of up to -341.06 kJ⋅mol-1. AP and MB were most likely bound by -COO and S atoms. Overall, AP/MIMO exhibits high adsorption capacity and shows potential as a high-performance magnetic polymer for MB removal.

Spatial nanopores promote laccase degradation of bisphenol A and its analogs

Bisphenol A (BPA) and its analogs are endocrine-disrupting chemicals that are frequently detected in environmental and human samples. However, the effective removal of BPA and its analogs has not yet been extensively studied. Herein, we introduce a novel enzyme reactor for the degradation of BPA and its analogs in water. The influence of pore size on the degradation efficiency of immobilized laccase in the spatial nanopores of hydrogel was investigated using BPA as a representative compound. This showed that nanopores enhance the activity of immobilized laccases in a pore size-dependent manner and increase their stability. Compared with the same amount of free laccase, the 50 mg/L BPA degradation performance of laccase immobilized in 76 nm nanopores increased to 300 %. Taking advantage of magnetic separation, this immobilized laccase can be reused, and its degradation capacity was maintained at over 73.7 % after ten reactions. Moreover, the degradation of seven BPA analogs was 1.03-5.88 times higher using laccase immobilized in nanopores compared with free laccase. Also, the biocatalyst could efficiently degrade BPA analogs in real water matrix. This study opens up a new avenue for the removal of BPA and its analogs by immobilizing laccase in nanopores, overcoming the key limitations introduced by the short enzyme life span and non-reusability.

Bisphenol A contamination in aquatic environments: a review of sources, environmental concerns, and microbial remediation

The production of polycarbonate, a high-performance transparent plastic, employs bisphenol A, which is a prominent endocrine-disrupting compound. Polycarbonates are frequently used in the manufacturing of food, bottles, storage containers for newborns, and beverage packaging materials. Global production of BPA in 2022 was estimated to be in the region of 10 million tonnes. About 65-70% of all bisphenol A is used to make polycarbonate plastics. Bisphenol A leaches from improperly disposed plastic items and enters the environment through wastewater from plastic-producing industries, contaminating, sediments, surface water, and ground water. The concentration BPA in industrial and domestic wastewater ranges from 16 to 1465 ng/L while in surface water it has been detected 170-3113 ng/L. Wastewater treatment can be highly effective at removing BPA, giving reductions of 91-98%. Regardless, the remaining 2-9% of BPA will continue through to the environment, with low levels of BPA commonly observed in surface water and sediment in the USA and Europe. The health effects of BPA have been the subject of prolonged public and scientific debate, with PubMed listing more than 17,000 scientific papers as of 2023. Bisphenol A poses environmental and health hazards in aquatic systems, affecting ecosystems and human health. While several studies have revealed its presence in aqueous streams, environmentally sound technologies should be explored for its removal from the contaminated environment. Concern is mostly related to its estrogen-like activity, although it can interact with other receptor systems as an endocrine-disrupting chemical. Present review article encompasses the updated information on sources, environmental concerns, and sustainable remediation techniques for bisphenol A removal from aquatic ecosystems, discussing gaps, constraints, and future research requirements.

Ni-Al layered double hydroxide-coupled layered mesoporous titanium dioxide (Ni-Al LDH/LM-TiO2) composites with integrated adsorption-photocatalysis performance

Nickel aluminum layered double hydroxides (Ni-Al LDHs) and layered mesoporous titanium dioxide (LM-TiO₂) were prepared via a simple precipitation process and novel precipitation-peptization method, respectively, and Ni-Al LDH-coupled LM-TiO₂ (Ni-Al LDH/LM-TiO₂) composites with dual adsorption and photodegradation properties were obtained via the hydrothermal approach. The adsorption and photocatalytic properties were investigated in detail with methyl orange as the target, and the coupling mechanism was systematically studied. The sample with the best performance was recovered after photocatalytic degradation, which was labeled as 11% Ni-Al LDH/LM TiO₂(ST), and characterization and stability studies were carried out. The results showed that Ni-Al LDHs showed good adsorption for pollutants. Ni-Al LDH coupling enhanced the absorption of UV and visible light, and the transmission and separation of photogenerated carriers were also significantly promoted, which was conducive to improving the photocatalytic activity. After treatment in the dark for 30 min, the adsorption of methyl orange by 11% Ni-Al LDHs/LM-TiO₂ reached 55.18%. Under illumination for 30 min, the decolorization rate of methyl orange solution reached 87.54%, and the composites also showed an excellent recycling performance and stability.

A novel multifunctional β-cyclodextrin polymer as a promising sorbent for rapid removal of methylene blue from aqueous solutions

Production wastewater has evolved with dye and printing technology to become one of the major sources of soil and water contamination. The majority of dyes are carcinogenic, teratogenic, and mutagenic compounds. As a result, dealing with the dye in the wastewater is a critical issue. Insoluble polymers of β-cyclodextrin (β-CD), an inexpensive, sustainably produced macrocycle of glucose, have potential to remove dyes from water/wastewater via sorption due to formation of well-defined host-guest complexes. A novel polymeric sorbent based on cyclodextrin was successfully synthesized in a one-step reaction with few reagents. The polymer is characterized by multifunctionality and cross-linked network structure. The sorption studies aimed at the removal of methylene blue (MB) from aqueous solutions. The dominant model was Langmuir isotherm which indicated a sorption capacity of 96.15 mg/g. The rapid removal has already been obtained after 1 min, around 84 % of efficiency. The molecular mechanism of MB sorption by poly(β-CD-BPDA) network is found mostly on the electrostatic interactions and partially on the inclusion of complexation inside supramolecular pores based on cyclodextrins' cavities, hydrogen bonding and slightly π-stacking. The presented polymer seems to be a promising sorbent for the removal of hazardous organic pollutants from water/wastewater.

Efficient recovery of bisphenol A from aqueous solution using K2CO3 activated carbon derived from starch-based polyurethane

Endocrine-disrupting compounds (EDCs) are increasingly polluting water, making it of practical value to develop novel desirable adsorbents for removing these pollutants from wastewater. Here, a simple cross-linking strategy combined with gentle chemical activation was demonstrated to prepare starch polyurethane-activated carbon (STPU-AC) for adsorbing BPA in water. The adsorbents were characterized by various techniques such as FTIR, XPS, Raman, BET, SEM, and zeta potential, and their adsorption properties were investigated comprehensively. Results show that STPU-AC possesses a large surface area (1862.55 m²·g^-1) and an abundance of functional groups, which exhibited superior adsorption capacity for BPA (543.4 mg·g^-1) and favorable regenerative abilities. The adsorption of BPA by STPU-AC follows a pseudo-second-order kinetic model and a Freundlich isotherm model. The effect of aqueous solution chemistry (pH and ionic strength) and the presence of other contaminants (phenol, heavy metals, and dyes) on BPA adsorption was also analyzed. Moreover, theoretical studies further demonstrate that hydroxyl oxygen and pyrrole nitrogen are the primary adsorption sites. We found that the efficient recovery of BPA was associated with pore filling, hydrogen-bonding interaction, hydrophobic effects, and π-π stacking. These findings demonstrate the promising practical application of STPU-AC and provide a basis for the rational design of starch-derived porous carbon.

Adsorption of 2,4-dichlorophenoxyacetic acid and glyphosate from water by Fe3O4-UiO-66-NH2 obtained in a simple green way

In this study, a green adsorbent (Fe₃O₄-UiO-66-NH₂) with the ability of addressing the issues of separation and recovery of UiO-66-NH₂ is obtained using a simple co-precipitation method under environmentally benign conditions. Various characterization techniques are utilized for evaluating the properties of the developed adsorbent. The capability of Fe₃O₄-UiO-66-NH₂ towards 2,4-dichlorophenoxyacetic acid (2,4-D) and glyphosate (GP) from solution is explored. The results revealed that the magnetization process did not destroy the crystal structure of UiO-66-NH₂, which ensured that Fe₃O₄-UiO-66-NH₂ had good adsorption performance for 2,4-D and GP. The adsorption processes showed a wide pH application range, high salt tolerance, and regeneration performance as well as an excellent adsorption rate. Results from thermodynamic study showed that both processes were spontaneous and endothermic. The unit uptake ability of Fe₃O₄-UiO-66-NH₂ for 2,4-D and GP reached up to 249 mg·g^-1 and 183 mg·g^-1 from Langmuir model at 303 K, respectively. When solid-liquid ratio was 2 g·L^-1, Fe₃O₄-UiO-66-NH₂ can reduce the content of 2,4-D or GP with the initial density of 100 mg·L^-1 below the drinking water requirement limit. In addition, the reusability efficiency of Fe₃O₄-UiO-66-NH₂ towards 2,4-D and GP was found to be 86% and 80% using 5 mmol·L^-1 NaOH as eluent. Analysis of simulated water samples indicated that Fe₃O₄-UiO-66-NH₂ could achieve the single or simultaneous removal of 2,4-D and GP from wastewater. Summarily, Fe₃O₄-UiO-66-NH₂ as a green adsorbent can serve as an alternative for removing 2,4-D and GP from water body.

Rapid, Highly-Efficient and Selective Removal of Anionic and Cationic Dyes from Wastewater Using Hollow Polyelectrolyte Microcapsules

Herein, poly (allylamine hydrochloride) (PAH)/ poly (styrene sulfonic acid) sodium salt (PSS) microcapsules of (PAH/PSS)2PAH (P2P MCs) and (PAH/PSS)2 (P2 MCs) were obtained by a layer-by-layer method. The P2 MCs show high adsorption capacity for Rhodamine B (642.26 mg/g) and methylene blue (909.25 mg/g), with an extremely low equilibrium adsorption time (~20 min). The P2P MCs exhibited high adsorption capacities of reactive orange K-G (ROKG) and direct yellow 5G (DY5G) which were 404.79 and 451.56 mg/g. Adsorption processes of all dyes onto microcapsules were best described by the Langmuir isotherm model and a pseudo-second-order kinetic model. In addition, the P2P MCs loaded with reactive dyes (P2P–ROKG), could further adsorb rhodamine B (RhB) dye, and P2 MCs that had adsorbed cationic MB dyes could also be used for secondary adsorption treatment of direct dye waste-water, respectively. The present work confirmed that P2P and P2 MCs were expected to become an excellent adsorbent in the water treatment industry.

Adsorption of chlorophenols on activated pine sawdust-activated carbon from solution in batch mode

In this work, a novel adsorbent, activated carbon (PSAC) developed by the activation of pine sawdust's pyrolytic carbon (PSPC), is applied to adsorb 2,4-dichlorophenol (2,4-DCP) and 4-chlorophenol (4-CP). The optimized preparation conditions of PSAC were presented. The results revealed that equilibrium adsorption capacity (q_e) of PSAC was notably enhanced up to threefold compared with PSPC. The adsorbents were characterized by a variety of techniques such as SEM, XRD, FT-IR, and elemental analysis. The key factors (such as adsorbent dosage, pH, salt concentration, temperature, and contact time) influencing the adsorption process were also studied. The adsorption quantities of PSAC for 2,4-DCP and 4-CP were 135.7 mg·g^-1 and 77.3 mg·g^-1, respectively. The equilibrium adsorption of 4-DCP and 4-CP was suitable to be predicted by the Freundlich and Koble-Corrigan models, while kinetic process was better described by the pseudo-second-order kinetic model and Elovich equation. The process was spontaneous. After repeated regeneration of PSAC with ethanol, the adsorption capacity of PSAC was not significantly reduced, indicating that PSAC can be recycled by regeneration after adsorption of 4-CP. This work provides a viable method to use activated carbon as an effective adsorbent for pollutant removal.

Copyrolysis of microalga Chlorella sp. and alkali lignin with potassium carbonate impregnation for synergistic Bisphenol A plasticizer adsorption

Composite functional materials offer promising opportunities for the development of tailored adsorbents with enhanced bioremediation potential towards toxic, carcinogenic endocrine disrupters such as Bisphenol A (BPA). Copyrolysis of microalga Chlorella sp. (CH) alkali lignin (L) with K₂CO₃ impregnation yielded a carbon-based composite (CHL-AC) with a micro-mesoporous structure of 0.643 cm³/g, surface area of 1414 m²/g, and BPA adsorption capacity of Q_max 316.858 mg/g. Enhanced BPA removal efficiency indicated a positive synergistic effect upon a combination of L and CH, resulting in a 73.24 % removal efficiency compared with the individual carbon components of 52.33 % for L-AC and 67.35 % for CH-AC. The kinetics and equilibrium results were described well by the pseudo second-order kinetic model and Freundlich isotherm, respectively. This paper elucidates the blending of microalgae and lignin into high-value carbon composite material, CHL-AC, with immense potential for the treatment of BPA-contaminated waters to contribute to Goal 6 (clean water and sanitation).

Removing methylene blue from water: A study of sorption effectiveness onto nanoparticles-doped activated carbon

In this present study, silver (Ag) and titanium dioxide (TiO₂) nanoparticles were successfully deposited on coconut shell-derived activated carbon (CSAC), to synthesize a novel nanocomposite (CSAC@AgNPs@TiO₂NPs) for the adsorption of Methylene Blue (MB) dye from aqueous solution. The fabricated CSAC@AgNPs@TiO₂NPs nanocomposite was analyzed by Scanning Electron Microscope (SEM), X-ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FTIR), Transmission Electron Microscope (TEM) equipped with Energy Dispersive X-ray spectroscopy (EDS) detector, X-ray Photoelectron Spectroscope (XPS), and Brunauer-Emmett-Teller (BET). The successful deposition of AgNPs and TiO₂NPs on CSAC surface was revealed by the TEM/EDX, SEM, and XPS analysis. The mesopore structure of CSAC@AgNPs@TiO₂NPs has a BET surface area of 301 m²/g. The batch adsorption studies were conducted and the influence of different parameters, i.e., adsorbent dose, adsorption time, initial dye concentration, pH and temperature were investigated. The nonlinear isotherm and kinetic modelling demonstrated that adsorption data were best fitted by Sips isotherm and pseudo-second-order models, respectively. The maximum adsorption capacity of MB onto CSAC@AgNPs@TiO₂NPs by the Sips model was 184 mg/g. Thermodynamic results revealed that the adsorption was endothermic, spontaneous and physical in nature. CSAC@AgNPs@TiO₂NPs revealed that MB absorption by CSAC@AgNPs@TiO₂NPs was spontaneous and endothermic. The uptake capacity of MB was influenced significantly by the presence of competing ions including, NO₃^-, HCO_3, Ca²⁺, and Na⁺. Repeated tests indicated that the CSAC@AgNPs@TiO₂NPs can be regenerated and reused six times before being discarded. The primary separation mechanism between MB dye and CSAC@AgNPs@TiO₂NPs was the electrostatic interaction. Thus, CSAC@AgNPs@TiO₂NPs was an outstanding material, which displayed good applicability in real water with ≥ 97% removal of MB dye.

Cold plasma-assisted regeneration of biochar for dye adsorption

Environmental remedies, including adsorption-based water purification, are now being asked to meet the requirement for a low-carbon circular economy requiring low energy and low material consumption. In this regard, we tested the possibility of regenerating adsorbents via cold plasma (CP) treatment for less use of adsorbents and no washing solution. In the adsorption of methylene blue (MB) using carbonized rice husk (CRH) and five successive regeneration cycles by CP treatment, the removal efficiencies were maintained at a moderate level (∼70% of the initial performance), unlike five consecutive adsorption without CP treatment (∼9-13% of the initial performance). The regeneration of CRH by CP treatment was also double-checked by the FESEM, EDS, BET, FTIR, XPS, and surface zeta potential measurements. The successfully recovered adsorption capability is related to the remediation of adsorption sites. It is also worth noting that the required power consumption for recycling by CP treatment was about 6.4 times lower than carbonizing new rice husks. This work provides insights into recovering adsorbents using CP without rigorous, costly, and energy-intensive processes.

Competitive removal mechanism to simultaneously incarcerate bisphenol A, triclosan and 4-tert-octylphenol within beta-cyclodextrin crosslinked citric acid used for encapsulation in polypropylene membrane protected-micro-solid-phase extraction

Endocrine disrupting compounds (EDCs) are extensively found in the environment and severely impacting human health. In addressing this issue, the beta-cyclodextrin crosslinked citric acid (BCD-CA) had been previously employed in membrane-protected micro-solid phase extraction for sequestering EDCs from water medium; and the findings revealed that BCD-CA possessed a selectivity property. On that account, the potential of BCD-CA towards competitive adsorption of selected EDCs was investigated in terms of adsorption mechanism and selectivity property. Factors that affected the removal efficiencies such as sample pH, sorbent dosage, contact time and initial concentration were evaluated. The characterization results revealed that the carbon percentage of BCD-CA had increased by 2.04%, while the hydrogen percentage had reduced by 1.83%, signifying the successful crosslinking of BCD-CA. Besides, the amount of active BCD was calculated to be 3.2 × 10^-7 mol, while the amount of carboxyl group was 2.48 × 10^-5 mol per 4 mg of BCD-CA. Moreover, BCD-CA was stable in an aqueous medium with the zeta potential obtained at -36.5 mV and had a high-water retention capacity (∼150%). The competitive adsorption mechanism by BCD-CA with EDCs followed the pseudo-second-order kinetics and Freundlich isotherm, suggesting that the adsorption process was dominated by chemisorption on the heterogeneous surface of the adsorbent. Thermodynamic results revealed that adsorption of 4-tert-octylphenol had the most negative ΔG value, indicating most favorable to be adsorbed by BCD-CA as opposed to triclosan and bisphenol A, which was coherent with the apparent formation constant results. These unique properties manifested the practicality of BCD-CA as a selective adsorbent to detect and remove EDCs from the water medium.

Removal of micropollutants through bio-based materials as a transition to circular bioeconomy: Treatment processes involved, perspectives and bottlenecks

The recent increase in micropollutant levels in water bodies is a growing concern globally. The generation of new materials and techniques for wastewater treatment often involves the release of hazardous wastes and the utilization of energy related to it. This can be resolved by the synthesis of bio-based materials through the use of already released wastes and naturally occurring components, adding their value as reusable resources. These bio-based materials find wide applications for micropollutant elimination and energy tapping due to the presence of various functional groups, large surface area, high stability, and reusability. The processes involved in micropollutant elimination through biomaterials generally include adsorption and degradation. These treatment processes are suggested to depend on various operational parameters like pH, temperature, dose, reaction time, presence of other contaminants, ions, etc. in the system, which may influence the process efficiency. Understanding the potential of bio-based materials many steps can be taken towards its large-scale application to upgrade wastewater treatment plants for micropollutant elimination. Furthermore, the recent advances of bio-based materials in energy storage and conversion have widened its scope for implementation in a circular bioeconomy. The bottlenecks towards such a transition and future recommendations are also presented and discussed.

Efficient removal of 2,4-D from solution using a novel antibacterial adsorbent based on tiger nut residues: adsorption and antibacterial study

We engineered a tiger nut residue (TNR, a low-cost agricultural waste material) through a facile and simple process to take advantage of the introduced functional groups (cetylpyridinium chloride, CPC) in the removal of 2,4-dichlorophenoxyacetic acid (2,4-D) in batch mode and further investigated its impingement on bacterial growth in a yeast-dextrose broth. The surface characterizations of the adsorbent were achieved through Fourier-transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller method (BET), X-ray diffraction analysis (XRD), and X-ray photoelectron spectroscopy (XPS). The batch adsorption studies revealed that solution pH, adsorbent dose, temperature, and salt affected the adsorptive capacity of TNR-CPC. The equilibrium data were best fitted by Langmuir isotherm model with a maximum monolayer adsorption capacity of 90.2 mg g^-1 at 318 K and pH 3. Pseudo-second-order model best fitted the kinetics data for the adsorption process. Physisorption largely mediated the adsorption system with spontaneity and a shift in entropy of the aqueous solid-solute interface reflecting decreased randomness with an exothermic character. TNR-CPC demonstrated a good reusability potential making it highly economical and compares well with other adsorbents for decontamination of 2,4-D. The adsorption of 2,4-D proceeded through a probable trio-mechanism; electrostatic attraction between the carboxylate anion of 2,4-D and the pyridinium cation of TNR-CPC, hydrogen bonding between the hydroxyl (-OH) group inherent in the TNR and the carboxyl groups in 2,4-D and a triggered π-π stacking between the benzene structures in the adsorbate and the adsorbent. TNR-CPC reported about 99% inhibition rate against both gram-positive S. aureus and gram-negative E. coli. It would be appropriate to investigate the potential of TNR-CPC as a potential replacement to the metal oxides used in wastewater treatment for antibacterial capabilities, and its effects against airborne bacteria could also be of interest.

Hydroxypropyl methylcellulose-sugarcane bagasse adsorbents for removal of 17α-ethinylestradiol from aqueous solution and freshwater

Adsorbents made of hydroxypropyl methylcellulose (HPMC) and sugarcane bagasse (BG) microparticles were applied for the separation of 17α-ethinylestradiol (EE2) from aqueous solution in batch, and from aqueous solution and freshwater in fixed-bed columns. HPMC chains and BG microparticles were crosslinked by the esterification with citric acid. The adsorbents presented compression modulus values that increased from 208 ± 20 kPa (pure HPMC) to 917 ± 90 kPa, when the content of BG particles added to HPMC was 50 wt% (HPMC50BG). The porosity (~ 97%), specific surface area (1.16 ± 0.10 m²/g) and swelling degree (20 ± 1 g water/g) values were not affected by the addition of BG particles. The adsorption isotherms determined for EE2 on HPMC and on HPMC50BG fitted to the Langmuir and Freundlich models; the adsorption capacity of HPMC was slightly higher than that of composite HPMC50BG. Nevertheless, the addition of BG particles rendered outstanding mechanical reinforcement and dimensional stability to the adsorbents. The adsorption was driven by (i) hydrophobic interactions between EE2 methylene and aromatic groups and HPMC methyl groups, as evidenced by FTIR spectroscopy, and (ii) H bonds between HPMC and EE2 hydroxyl groups, as revealed by the adsorption enthalpy change (ΔH_ads) of - 45 kJ/mol. Column adsorption experiments of EE2 from aqueous solution on HPMC and HPMC50BG indicated adsorptive capacity (q₀) values of 8.06 mg/g and 4.07 mg/g, respectively. These values decreased considerably for the adsorption of EE2 from river water, probably due to the competition of EE2 with humic substances dissolved in natural water. The HPMC adsorbents could be recycled retaining up to 83% of the original efficiency.

Investigation of two new low-cost adsorbents functionalized with magnetic nanoparticles for the efficient removal of triclosan and a synthetic mixture

Triclosan (TCS) is widely used in the production of antibacterial products, being often found in wastewater. Therefore, this study developed new materials via soybean hulls (SBH_F) and açaí seeds (AÇS_F) functionalization with iron oxide nanoparticles to be applied in the TCS adsorption. The characterization confirmed the functionalization of the materials. The adsorption results indicated that the equilibrium of the process occurred after 480 and 960 min for SBH_F and AÇS_F, respectively. The maximum adsorptive capacity values were 158.35 and 155.09 mg g^-1 for SBH_F and AÇS_F, respectively, at 318 K. The kinetic and isothermal data better fitted to the pseudo-second-order and Langmuir models. Thermodynamics indicated that the processes had an endothermic, spontaneous, and reversible character. The main adsorption mechanisms were H-bond and π-interactions. The pH and ionic strength studies indicated that the adsorption efficiency has not been reduced pronouncedly. The biosorbents reuse was effective for five cycles. In the synthetic mixture, the removal rate was satisfactory (92.53% and 57.02%, respectively for SBH_F and AÇS_F)_. These results demonstrate the biosorbents high potential for large-scale application.

Constructing a 3D interconnected "trap-zap" β-CDPs/Fe-g-C3N4 catalyst for efficient sulfamethoxazole degradation via peroxymonosulfate activation: Performance, mechanism, intermediates and toxicity

A novel and high-efficiency catalyst Fe doped g-C₃N₄ (Fe-g-C₃N₄) composited with β-cyclodextrin polymers (β-CDPs) was synthesized for activating peroxymonosulfate (PMS). The scanning electron microscopy (SEM) and transmission electron microscopy (TEM) results showed that the catalyst was 3D interconnected porous structure. The degradation rate constant of sulfamethoxazole (SMX) in β-CDPs/Fe-g-C₃N₄+PMS system was estimated to be 0.132 min^-1, which was 14.7 times and 2.2 times that of g-C₃N₄+PMS and Fe-g-C₃N₄+PMS system, respectively. In addition, the β-CDPs/Fe-g-C₃N₄ exhibited superior degradation performance in a wide pH range (3.0-9.0) and good selectivity in the presence of other inorganic anions and natural organics. Radical scavenging, electron paramagnetic resonance (EPR) and electrochemical measurements indicated that ¹O₂ and Fe(V)O were the main active species for SMX degradation in β-CDPs/Fe-g-C₃N₄+PMS system. Moreover, β-CDPs accelerated electron transfer between catalyst and PMS and promoted the generation of reactive oxygen species (ROS) during PMS activation. The loading of β-CDPs increased the yields of Fe(V)O and ¹O₂ in the system and limited the leaching of Fe³⁺. In addition, the possible degradation pathways of SMX were described based on the intermediates detected by liquid chromatography-mass spectrometry (LC-MS), and the toxicity of the intermediates was also evaluated. This work investigate the role of β-CDPs in PMS activation for the first time and develop a promising material with potential for water treatment.

Amine-grafted walnut shell for efficient removal of phosphate and nitrate

The presence of emerging pollutants such as PO₄^3- and NO₃^- in water bodies has attracted worldwide concern about their severe effects on water bodies and the health of humankind in general. Therefore, to preserve the health of humankind and environmental safety, it is of the essence that industrial effluents are treated before they are discharged into water bodies. Amine functionalized walnut shells (ACWNS) were synthesized, characterized, and then tested as a novel adsorbent for PO₄^3- and NO₃^- removal. The effects of pH, dosage, initial phosphate concentration, interference ions, and temperature on the removal of phosphate and nitrate were investigated. Notably, the adsorption of PO₄^3- and NO₃^- was exothermic and spontaneous, with a maximum uptake capacity of phosphate and nitrate, at 293 K, 82.2 and 35.7 mg g^-1, respectively. The mechanism by which these ions were adsorbed onto ACWNS could be electrostatic interactions and hydrogen bonding. Pseudo-second-order kinetic model fitted the PO₄^3- and NO₃^- adsorption, while Freundlich and Langmuir models best fitted the PO₄^3- and NO₃^- adsorption, respectively. Furthermore, in the binary system, the uptake capacity of phosphate decreased by 14.4% while nitrate witnessed a reduction in its uptake capacity of 10.4%. ACWNS has a higher attraction towards both ions and this could be attributed to the existence of a variety of active areas on ACWNS that exhibit a degree of specificity for the individual ions. Results obtained from real water sample analysis confirmed ACWNS as highly efficient to be utilized for practical remediation processes.

Impregnation of Silver Nanoparticles onto Polymers Based on Sugarcane Bagasse for the Remediation of Endocrine Disruptor–Bisphenol A from Water

This present study introduces a contemporary innovation of synthesized polymer–silver nanoparticle nanocomposite adsorbent based on sugarcane bagasse (AgNP-SB-βCD) for the sequestration of emerging micropollutant–bisphenol A from water matrix. Batch adsorption mode was carried out to assess the effectiveness of AgNP-SB-βCD nanocomposites towards eliminating bisphenol A (BPA). Characterization techniques including SEM, FTIR, and XRD have confirmed the successful incorporation of silver nanoparticles (AgNPs) onto bagasse–polymer. At 25°C, pH 7, and contact time of 120 min, the nanocomposites had a maximum uptake capacity of 158.4 mg g-1on BPA. The equilibrium isotherm of BPA on AgNPs-SB-βCD has fitted effectively with Langmuir model while the adsorption kinetics conformed to pseudo-second order. The adsorption phenomenon was controlled mainly by physisorption (via host–guest inclusion van der Waals bonding and pore filling effect). In addition, oxidative degradation of BPA by AgNPs-SB-βCD could marginally contribute the removal of BPA due to oxidative dissolution of AgNPs at pH 7. The thermodynamic results substantiate the spontaneity and exothermic behaviors of the adsorption phenomenon. The polymeric nanocomposite adsorbent was regenerated five times (using 75% ethanol) without considerable loss of its adsorption capacity. This authenticates its reusability and consistency performances; accordingly, it can be a market competitor adsorbent for the treatment of water contaminated with BPA.

Facile synthesis of novel multifunctional β-cyclodextrin microporous organic network and application in efficient removal of bisphenol A from water

Here, a novel multifunctional β-cyclodextrin microporous organic network (CD-MON) has been successfully synthesized and used to remove bisphenol A (BPA) from water. The morphology and composition of the synthesized CD-MON were confirmed. The combination of hydrophobic interaction, π-π interaction inclusion mechanism and hydrogen bonding endowed CD-MON to exhibit superior adsorption capacity toward BPA. The adsorption kinetics and isotherms of BPA and other four model aromatic pollutants on CD-MON were studied. CD-MON could maintain adsorption efficiency toward BPA over wide pH ranges and without being affected by the ionic strengths, co-existing inorganic ions and humic acid. The optimal conditions and removal efficiency of BPA were screened by response surface analysis. In addition, nearly unchanged in the adsorption efficiency toward BPA was observed after five regeneration cycles on CD-MON. CD-MON can adsorb about 80% of five model aromatic pollutants from the water within 40 s in the flow-through experiments. This novel adsorbent gives great promise for practical wastewater remediation.

CTAB-modified carboxymethyl cellulose/bagasse cryogels for the efficient removal of bisphenol A, methylene blue and Cr(VI) ions: Batch and column adsorption studies

The simultaneous removal of organic and inorganic pollutants from water requires multifunctional adsorbents. Cryogels of carboxymethyl cellulose (CMC) and sugarcane bagasse (BG) were modified with cetyltrimethylammonium bromide (CTAB) micelles for the adsorption of methylene blue (MB), Cr(VI) ions and bisphenol A (BPA) separately, in binary or ternary aqueous mixtures. Batch adsorption studies of MB and Cr(VI) and BPA on the CMCBG-CTAB adsorbents indicated removal capacities of 100%, 70% and 95%, respectively. MB adsorbed as multilayers on the CMCBG walls by electrostatic interaction, whereas Cr(VI) and BPA adsorbed on the cationic CTAB micelles surface and hydrophobic core of CTAB micelles, respectively. The breakthrough curves obtained for pure adsorbates and their mixtures showed that the adsorption of Cr(VI) ions increased (i) ~ 3.5 times in binary mixture with BPA or in the ternary mixture, in comparison to pure Cr(VI) solution, and (ii) 1.4 times in binary mixture with MB molecules, due to synergistic effects. In the presence of Cr(VI) ions in binary or ternary mixtures, the adsorption of MB was dramatically reduced due to screening effects. The adsorption of BPA was not significantly affected by the presence of MB or Cr(VI). The adsorbents were recycled five times without significant efficiency loss.

Modification of cyclodextrin and use in environmental applications

Water pollution, which has become a global problem in parallel with environmental pollution, is a problem that needs to be solved urgently, considering the gradual depletion of water resources. The inadequacy of the water treatment methods and the materials used somehow directed the researchers to look for dual character structures such as biocompatible and biodegradable β-cyclodextrin (β-CD). β-CD, which is normally insoluble in water, is used in demanding wastewater applications by being modified with the help of different agents to be water soluble or transformed into polymeric adsorbents as a result of co-polymerization via cross-linkers. In this way, in addition to the host-guest interactions offered by β-CD, secondary forces arising from these interactions provide advantages in terms of regeneration and reusability. However, the adsorption efficiency and synthesis steps need to be improved. Based on the current studies presented in this review, in which cross-linkers and modification methods are also mentioned, suggestions for novel synthesis methods of new-generation β-CD-based materials, criticisms, and recent methods of removal of micropollutants such as heavy metals, industrial dyes, harmful biomolecules, and pharmaceutics wastes are mentioned.

Resin immobilized gold nanocomposites assisted surface enhanced infrared absorption (SEIRA) spectroscopy for improved surface assimilation of methylene blue from aqueous solution

In the present work, we report the adsorption of the methylene blue (MB) dye from an aqueous solution employing resin immobilized gold nanocomposites (R-AuNCs) assisted surface-enhanced infrared absorption (SEIRA) spectroscopy. The appropriate adsorption isotherm models, including the Langmuir, Freundlich, and Temkin are tested to reveal the interactive behavior between the adsorbent (R-AuNCs) and adsorbed (MB). Interestingly, Fourier transform infrared spectroscopy (FTIR) in combination with R-AuNC materials could be another approach through which the analysis of adsorption-desorption of MB on the surface of nanocomposite adsorbents is possible in a more precise way with high sensitivity and adsorptivity. In addition, a 10-fold enhancement of the signal intensity of MB dye was obtained due to the electrostatic interaction and H-bonding interaction between COO^- groups of adsorbent and the positively charged active sites of the dye molecules. The value of % removal efficiency and % adsorption obtained in the present method was 77.64% and 186.61%, respectively. Desorption of MB from adsorbent surface was also carried out using 0.1 M cetylpyridinium chloride as cationic surfactant; resulting process shows for 'n' number of cyclic process. The maximum desorption capacity for MB found in the present investigation was 44.38 mg/g, The advantages of current method are its simplicity, sensitivity, rapidity, ease to fabrication and excellent adsorption efficiencies to remove MB dye from aqueous solution.

Application of biodegradable cellulose-based biomass materials in wastewater treatment

Water bodies contain a large number of harmful environmental pollutants, including oil, heavy metal ions and dyes, which has become a major global problem. The current work focusses on the development and future prospect of sustainable application of biodegradable cellulose-biomass materials in water treatment, considering that they show an important prospect in wastewater treatment. This paper summarizes the advantages and disadvantages of cellulose-biomass materials in removing harmful substances and pollutants from water and the key problems the technology faces. Cellulose-biomass material has unique structure, is environment friendly, degradable, renewable and provides low energy cost benefits, among other advantages. In this paper, the research progress of wastewater treatment in recent years is reviewed from the following three aspects: oil-water separation, heavy metal ions in water, and dye adsorption. The future research direction is also discussed.

Adsorption performance of modified agricultural waste materials for removal of emerging micro-contaminant bisphenol A: A comprehensive review

This review is an attempt to assess the adsorption performance of different green adsorbents derived from agricultural waste materials (AWMs) that were used for the elimination of bisphenol A (BPA) from aqueous matrices. Different processes including grafting, polymerization, activation and chemical treatment have been applied to functionalize and modify agricultural waste materials for the purposes of increasing their adsorptive performances toward BPA. The highest reported adsorption capacity of adsorbent from agricultural waste for the uptake of BPA is the highly microporous carbon adsorbent derived from Argan nut shell (1408 mg g^-1). Hydrogen bonding, hydrophobic and π-π interactions were reported in most studies as the main mechanisms governing the adsorption of BPA onto agricultural waste adsorbents. Equilibrium isotherm and kinetic studies for the uptake of BPA onto agricultural waste adsorbents were best described by Langmuir/Freundlich model and pseudo-second order model, respectively. Despite the effective elimination of BPA by various agricultural waste adsorbents, an appropriate selection of elution solvent is important for effective desorption of BPA from spent adsorbent. To date, ethanol, diethyl ether-methanol, methanol-acetic acid, mineral acids and sodium hydroxide are the most eluents applied for desorption of BPA molecules loaded onto AW-adsorbents. Looking toward the future, studies on the agricultural waste adsorbents based on polymers, activated carbons, nanoparticles and highly microporous carbons should be mostly considered by the researchers toward removing BPA. These future studies should be performed both in laboratory, pilot and industrial scales, and also should report the sustainable techniques for disposal of the spent AW-adsorbents after lose their adsorption performance on BPA.

Novel Chemical Architectures Based on Beta-Cyclodextrin Derivatives Covalently Attached on Polymer Spheres

This study presents the synthesis and characterization of polymer derivatives of beta-cyclodextrin (BCD), obtained by chemical grafting onto spherical polymer particles (200 nm) presenting oxirane functional groups at their surface. The polymer spheres were synthesized by emulsion polymerization of styrene (ST) and hydroxyethyl methacrylate (HEMA), followed by the grafting on the surface of glycidyl methacrylate (GMA) by seeded emulsion polymerization. The BCD-polymer derivatives were obtained using two BCD derivatives with hydroxylic (BCD-OH) and amino groups (BCD-NH2). The degree of polymer covalent functionalization using the BCD-OH and BCD-NH2 derivatives were determined to be 4.27 and 19.19 weight %, respectively. The adsorption properties of the materials were evaluated using bisphenol A as a target molecule. The best fit for the adsorption kinetics was Lagergren's model (both for Qe value and for R2) together with Weber's intraparticle diffusion model in the case of ST-HEMA-GMA-BCD-NH2. The isothermal adsorption evaluation indicated that both systems follow a Langmuir type behavior and afforded a Qmax value of 148.37 mg g-1 and 37.09 mg g-1 for ST-HEMA-GMA-BCD-NH2 and ST-HEMA-GMA-BCD-OH, respectively. The BCD-modified polymers display a degradation temperature of over 400 °C which can be attributed to the existence of hydrogen bonds and BCD thermal degradation pathway in the presence of the polymers.

Cross-linked FeCl3-activated seaweed carbon/MCM-41/alginate hydrogel composite for effective biosorption of bisphenol A plasticizer and basic dye from aqueous solution

A FeCl₃-activated seaweed carbon/MCM-41/alginate hydrogel composite (ECAC/MCM-41/ ALG) cross-linked with calcium chloride (2% CaCl₂) was synthesized for the biosorption of bisphenol A (BPA) plasticizer and basic blue (BB) dye. Biosorption uptakes of BPA and BB were performed in a batch mode with varying solution pH from 3 to 11, initial sorbate concentration from 25 to 300 mg/L, reaction time from 0 to 10 h, and biosorption temperature from 30 to 50 °C. The maximum BPA and BB uptake mechanisms were fast, which occurred within contact times of 1 and 2 h with monolayer coverage capacities of 222.32 and 190.11 mg/g at 50 °C, respectively. Cyclic biosorption/desorption behavior was evaluated via an ethanol elution to evaluate the feasibility of the ECAC/MCM-41/ALG for long-term application. Results revealed the biosorption renewability for five cycles up to 80% of the newly synthesized hydrogel composite for the purification of industrial wastewater laden with emerging contaminants.

Selective removal of anionic dyes in single and binary system using Zirconium and iminodiacetic acid modified magnetic peanut husk

A novel adsorbent (PN-Fe₃O₄-IDA-Zr) was developed from the chemical modification of peanut husk (a low cost material) with Fe₃O₄, iminodiacetic acid (IDA) and zirconium (Zr) and its efficacy for the sequestration of wastewater assessed using Alizarin red (AR) and Acid chrome blue K (AK) as model pollutants. To elucidate the characteristics of the formed adsorbent, analytical techniques such as the Bruauner-Emmet-Teller (BET) method, X-ray photoelectron spectroscopy (XPS), Fourier-transform infrared (FTIR) spectroscopy, X-ray diffractive spectroscopy (XRD) and vibrating sample magnetometer (VSM) were applied. Results from these studies confirmed the formation of a crystalline mesoporous adsorbent with surface properties which enhanced its usefulness. From the adsorption studies, it was observed that factors such as pH, salts, temperature and contact time influenced the uptake of the anionic dyes. The maximum monolayer capacity of PN-Fe₃O₄-IDA-Zr for AR was 49.4 mg g^-1 (at 313 K) and was well fitted by the Langmuir model with the chemisorption process being the dominant reaction mechanism. In binary systems, PN-Fe₃O₄-IDA-Zr exhibited higher affinity for AR as compared with AK. The significant removal efficiency exhibited by this novel adsorbent as well as other unique features such as easy retrieval and high regeneration promotes its prospects as an adsorbent for practical wastewater remediation processes.

Decontamination of bisphenol A and Congo red dye from solution by using CTAB functionalised walnut shell

In this research, the eco-friendly cationic surfactant modified walnut shell (WNS-CTAB) was synthesised to enhance the uptake for bisphenol A (BPA) and Congo red (CR) from aqueous solution. The characterisation of WNS-CTAB was performed using Fourier-transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), etc. to know its physiochemical properties. The adsorption equilibrium results were best described by the Langmuir isotherm model, which confirmed the monolayer adsorption of the pollutant molecules onto the adsorbent's surface. The maximum monolayer adsorption quantity of WNS-CTAB was established to be 38.5 mg g^-1 for BPA and 104.4 mg g^-1 for CR at 303 K, respectively. Pseudo-second-order kinetic models described the adsorption kinetics of both BPA and CR. Furthermore, the intra-particle diffusion was applied to analyse the kinetic results and was established that the rate was not solely controlled by diffusion. The mechanisms associated with BPA and CR adsorption onto the WNS-CTAB may include van der Waals interaction, hydrophobic interaction, and electrostatic force. WNS-CTAB demonstrated a good reusability potential with desorption through three successive adsorption-desorption cycles performed in both experiments. Moreover, in the binary system, the adsorption capacity of BPA witnessed a 66% decrease while CR saw marginal reduction of 8.0 %. This suggests that WNS-CTAB had a higher affinity for binding to CR with higher selectivity as compared with BPA. Therefore, WNS-CTAB has exhibited huge potential to serve as a functional material for practical use in the treatment of wastewater.