Removal of pharmaceuticals (diclofenac and amoxicillin) by maltodextrin/reduced graphene and maltodextrin/reduced graphene/copper oxide nanocomposites

Development of inorganic and mixed matrix membranes for application in toxic dyes-contaminated industrial effluents with in-situ treatments

Dyes are the most ubiquitous organic pollutants in industrial effluents. They are highly toxic to both plants and animals; thus, their removal is paramount to the sustainability of ecosystem. However, they have shown resistance to photolysis and various biological, physical, and chemical wastewater remediation processes. Membrane removal technology has been vital for the filtration/separation of the dyes. In comparison to polymeric membranes, inorganic and mixed matrix (MM) membranes have shown potentials to the removal of dyes. The inorganic and MM membranes are particularly effective due to their high porosity, enhanced stability, improved permeability, higher enhanced selectivity and good stability and resistance to harsh chemical and thermal conditions. They have shown prospects in filtration/separation, adsorption, and catalytic degradation of the dyes. This review highlighted the advantages of the inorganic and MM membranes for the various removal techniques for the treatments of the dyes. Methods for the membranes production have been reviewed. Their application for the filtration/separation and adsorption have been critically analyzed. Their application as support for advanced oxidation processes such as persulfate, photo-Fenton and photocatalytic degradations have been highlighted. The mechanisms underscoring the efficiency of the processes have been cited. Lastly, comments were given on the prospects and challenges of both inorganic and MM membranes towards removal of the dyes from industrial effluents.

Performance of magnetic nanocomposite based on xanthan gum-grafted-poly(acrylamide) crosslinked by borax for the effective elimination of amoxicillin from aquatic environments

This study evaluated the effectiveness of using nanocomposite (NCs) of xanthan gum grafted polyacrylamide crosslinked Borax - iron oxide nanoparticle (XG-g-pAAm-CL-Borax-IONP) to remove the amoxicillin antibiotic (AMX) from an aquatic environment. To confirm the structural characteristics of the prepared XG-g-pAAm-CL-Borax-IONP NCs, unique characterization methods (XRD, FT-IR, FE-SEM, EDX, BET, TGA, Zeta, and VSM) were used. Adsorption experimental setups were performed with the influence of solution pH (4-9), the effect of adsorbent dose (0.003-0.02 g), the effect of contact time (5-45 min), and the effect of initial AMX concentration (50-400 mg/L) to achieve the most efficient adsorption conditions. Based on the Freundlich isotherm model, XG-g-pAAm-CL-Borax-IONP NCs provided the maximum AMX adsorption capacity of 1183.639 mg/g. This research on adsorption kinetics also established that the pseudo-second-order model (R2 = 0.991) is outstanding compatibility with the experimental results. AMX adsorption on the NCs may occur through intermolecular hydrogen bonding, diffusion, and trapping into the polymer network. Even after five cycles, these NCs still displayed the best performance. Based on these results, XG-g-pAAm-CL-Borax-IONP NCs may be a viable material for the purification of AMX from contaminated water.

Asphaltene-derived nanocomposites for the removal of emerging pollutants and its antimicrobial effects: batch and continuous column studies

Emerging contaminants are diverse ecotoxic materials requiring unique treatment for removal. Asphaltenes are environmentally hazardous carbon-rich solid waste product of the petroleum industry. In the current work, asphaltene-derived activated carbon (AC) was loaded with silver (Ag/AC) and used to remove amoxicillin (AMX) and tetracycline (TC) from aqueous phase. The prepared Ag/AC was characterised using FESEM, FTIR, XRD and surface area analysis. The FESEM micrographs confirmed the spherical silver nanoparticle-laden porous AC, and the BET surface area was found to be 213 m2/g. Batch adsorption studies were performed, and the equilibrium data were fit into adsorption isotherm and kinetic models. The Ag/AC exhibited superior monolayer adsorption capacity of 1012 mg/g and 770 mg/g for AMX and TC, respectively. The continuous column studies were also performed to evaluate the breakthrough parameters. Furthermore, the antimicrobial activity of the adsorbent was evaluated using zone of inhibition studies. Ag/AC was found to have an 8-mm-diameter zone of microbial inhibition. The obtained results showed that Ag/AC was a promising material for the removal of antibiotics and inhibition of resistance-developed mutated microbes in effluent water.

Adsorbent biochar derived from corn stalk core for highly efficient removal of bisphenol A

Environmental-friendly biochar (BC) with low cost was obtained by simple pyrolysis of corn stalk core, which was employed as an adsorbent for efficiently removing organic pollutants in water. The physicochemical properties of BCs were characterized by various techniques, including X-ray diffractometer (XRD), Fourier transforms infrared (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectrometer (XPS), Raman, Thermogravimetric (TGA), N₂ adsorption-desorption and zeta potential tests. The influence of pyrolysis temperature on the structure and adsorption efficiency of the adsorbent was emphasized. The graphitization degree and sp² carbon content of BCs were enhanced by increasing the pyrolysis temperature, which was favorable for the enhancement of the adsorption efficiency. The adsorption results showed that corn stalk core calcined at 900 °C (BC-900) displayed exceptional adsorption efficiency toward bisphenol A (BPA) in wide pH (1-13) and temperature (0-90 °C) ranges. Moreover, adsorbent BC-900 could adsorb various pollutants from water, including antibiotics, organic dyes, and phenol (50 mg·L^-1). The adsorption process of BPA over BC-900 matched well with the Langmuir isotherm and pseudo-second-order kinetic model. Mechanism investigation suggested that large specific surface area and pore filling acted the foremost role in the adsorption process. Adsorbent BC-900 has the potential application in wastewater treatment due to its simple preparation, low cost, and excellent adsorption efficiency.

Graphene-based materials for effective adsorption of organic and inorganic pollutants: A critical and comprehensive review

Water scarcity has been felt in many countries and will become a critical issue in the coming years. The release of toxic organic and inorganic contaminants from different anthropogenic activities, like mining, agriculture, industries, and domestic households, enters the natural waterbody and pollutes them. Keeping this in view in combating the environmental crises, removing pollutants from wastewater is one of the ongoing environmental challenges. Adsorption technology is an economical, fast, and efficient physicochemical method for removing both organic and inorganic pollutants, even at low concentrations. In the last decade, graphene and its composite materials have become the center of attraction for numerous applications, including wastewater treatment, due to the large surface area, highly active surface, and exclusive physicochemical properties, which make them potential adsorbents with unique physicochemical properties, like low density, chemical strength, structural variability, and the possibility of large-scale fabrications. This review article provides a thorough summary/critical appraisal of the published literature on graphene-, GO-, and rGO-based adsorbents for the removal of organic and inorganic pollutants from wastewater. The synthesis methods, experimental parameters, adsorption behaviors, isotherms, kinetics, thermodynamics, mechanisms, and the performance of the regeneration-desorption processes of these substances are scrutinized. Finally, the research challenges, limitations, and future research studies are also discussed. Certainly, this review article will benefit the research community by getting substantial information on suitable techniques for synthesizing such adsorbents and utilizing them in water treatment and designing water treatment systems.

The Application of Hydroxyapatite NPs for Adsorption Antibiotic from Aqueous Solutions: Kinetic, Thermodynamic, and Isotherm Studies

Antibiotic pollution has become a serious concern due to the extensive use of antibiotics, their resistance to removal, and their detrimental effects on aquatic habitats and humans. Hence, developing an efficient antibiotic removal process for aqueous solutions has become vital. Amoxicillin (Amox) is one of the antibiotics that has been efficiently removed from an aqueous solution using hydroxyapatite nanoparticles (HAP NPs). The current study synthesizes and utilizes hydroxyapatite nanoparticles as a cost-effective adsorbent. Adsorbent dose, pH solution, initial Amox concentration, equilibrium time, and temperature are among the factors that have an evident impact on Amox antibiotic adsorption. The (200) mg dose, pH (5), temperature (25) °C, and time (120) min are shown to be the best-optimized values. The nonlinear Langmuir’s isotherm and pseudo-second-order kinetic models with equilibrium capacities of 4.01 mg/g are highly compatible with the experimental adsorption data. The experimental parameters of the thermodynamic analysis show that the Amox antibiotic adsorption onto HAP NPs powder is spontaneous and exothermic.

The effect of Fe-Zn mole ratio (2:1) bimetallic nanoparticles supported by hydroxyethyl cellulose/graphene oxide for high-efficiency removal of doxycycline

In this research, Hydroxyethyl cellulose - graphene oxide HEC-GO and HEC-GO/Fe-Zn mole ratio (2:1) nanocomposite as adsorbents were fabricated by crosslinking ethylene glycol dimethacrylate (EGDMA) to study the thermodynamic, kinetic and isotherm of doxycycline antibiotic adsorption. The morphology and structure of the adsorbents were analyzed by Fourier transform infrared spectroscopy (FT-IR), Field Emission Scanning Electron Microscopy with Energy Dispersive X-Ray Spectroscopy (FE-SEM- EDX), and Transmission electron microscopy (TEM). The adsorption behavior of doxycycline (DOX) was studied with different parameters including doxycycline concentration, pH, the dose of adsorbent (HEC-GO and HEC-GO/Fe-Zn, mole ratio (2:1)), contact time, and temperature. The optimal conditions for the removal of DOX are pH = 3.0, contact time 100 min, and 20 min for HEC-GO and HEC-GO/Fe-Zn mole ratio (2:1). The removal percentage for HEC-GO and HEC-GO/Fe-Zn mole ratio (2:1) was 97% and 95.5%, respectively. Equilibrium adsorption isotherms such as the Langmuir, Freundlich, and Temkin models were analyzed according to the experimental data. Also, four adsorption kinetics were investigated for removing DOX. The Langmuir isotherm and pseudo-second-order kinetic models provided the best fit for experimental data for HEC-GO and HEC-GO/Fe-Zn mole ratio (2:1). Thermodynamic data showed that negative values of Gibbs free energy (ΔG°) and the negative value of enthalpy (ΔH°) of the adsorption process for adsorbents. It means that DOX removal was a spontaneous and exothermic reaction.

Bentonite binding with mercury(II) ion through promotion of reactive oxygen species derived from manure-based dissolved organic matter

This study reports the mercury binding by bentonite clay influenced by cattle manure-derived dissolved organic matter (DOM). The DOM (as total organic carbon; TOC) was reacted with bentonite at 5.2 pH to monitor the subsequent uptake of Hg²⁺ for 5 days. The binding kinetics of Hg²⁺ to the resulting composite was studied (metal = 350 µM/L, pH 5.2). Bentonite-DOM bound much more Hg²⁺ than original bentonite and accredited to the establishment of further binding sites. On the other hand, the presence of DOM was found to decrease the Hg²⁺ binding on the clay surface, specifically, the percent decrease of metal with increasing DOM concentration. Post to binding of DOM with bentonite resulted in increased particle size diameter (~ 33.37- ~ 87.67 nm) by inducing the mineral modification of the pore size distribution, thus increasing the binding sites. The XPS and FTIR results confirm the pronounced physico-chemical features of bentonite-DOM more than that of bentonite. Hydroxyl and oxygen vacancies on the surface were found actively involved in Hg²⁺ uptake by bentonite-DOM composite. Furthermore, DOM increased the content of Hg²⁺ binding by ~ 10% (pseudo-second-order q_e = 90.9-100.0) through boosting up Fe³⁺ reduction with the DOM. The quenching experiment revealed that more oxygen functionalities were generated in bentonite-DOM, where hydroxyl was found to be dominant specie for Hg²⁺ binding. The findings of this study can be used as theoretical reference for mineral metal interaction under inhibitory or facilitating role of DOM, risk assessment, management, and mobilization/immobilization of mercury in organic matter-containing environment.

Effective adsorption of diclofenac sodium from aqueous solution using cationic surfactant modified Cuminum cyminum agri-waste: kinetic, equilibrium, and thermodynamic studies

The occurrence of pharmaceutical pollutants in aqueous media has increased where significant research is being conducted to eliminate these toxic compounds. In the present study, Tetradecyltrimethylammonium bromide (TTAB) modified Cuminum cyminum agri-waste (CCW) was prepared to investigate the removal of diclofenac sodium (DCF) from aqueous solution in the batch process for the first time. Physical and chemical characterizations of as-prepared adsorbent were conducted using field emission scanning electron microscopy, Fourier-transform infrared spectroscopy, N₂ adsorption-desorption, and point of zero charge analysis. Besides, the effect of the main parameters that affect the adsorption process, i.e., adsorbent dosage (0.25-6 g/L), contact time (0-300 min), initial DCF concentration (10-500 mg/L), and pH of the solution, were investigated. Furthermore, the resulted data were analyzed using various kinetic and isotherm models. The Pseudo-second-order model with R² = 0.9981 showed the highest agreement with kinetic behavior. Also, the maximum adsorption capacity of DCF is 93.65 mg/g, according to the Langmuir isotherm. In acidic media, the adsorption capacity reached the highest value (44.69 mg/g). As a result, this study revealed that the agri-waste material could be modified and, as a low-cost adsorbent, have promising adsorption potential to remove pharmaceutical contaminants from the aqueous solution.

Fabrication and implementation of bimetallic Fe/Zn nanoparticles (mole ratio 1:1) loading on hydroxyethylcellulose - Graphene oxide for removal of tetracycline antibiotic from aqueous solution

Tetracycline (TC) as an antibiotic with high consumption causes the spread of contamination in an aqueous solution. In recent decades, antibiotics are the main cause of hindering the growth of microorganisms. Also, they are one of the important groups of pharmaceuticals with extensive usage in human and veterinary medicine. In the first work of its kind, we used a suitable adsorbent of biodegradable hydroxyethylcellulose (HEC) with graphene oxide (GO) by crosslinking ethylene glycol dimethacrylate (EGDMA) and the Fe/Zn with mole ratio 1:1 bimetallic nanoparticles with HEC-GO support. The materials were identified using FTIR, FE-SEM, EDX, TEM, and TG- DSC analyses. The factors affecting the adsorption process (contact time, initial concentration of TC, solution pH, adsorbent dosage, and reaction temperature) were evaluated in a series of batch systems. The adsorption data showed that the high adsorption capacity was obtained on the HEC-GO and HEC-GO/Fe-Zn (mole ratio 1:1) nanocomposites at pH 3. Also, the contact time as the main factor affecting the adsorption process by adsorbents was investigated and the best contact time was 100 and 20 min. The TC removal percentages of both adsorbents were 85% and 95% for HEC-GO and HEC-GO/Fe-Zn, respectively. The maximum adsorption capacity for TC was evaluated by the isotherm models. The experimental data fitted well with the Langmuir model. In addition, pseudo-first-order, pseudo-second-order, intraparticle diffusion, and the Elovich models were applied to kinetic data. The data indicated that TC adsorption on HEC-GO and HEC-GO/Fe-Zn (mole ratio 1:1) followed the pseudo-second-order kinetic model. The thermodynamic parameters implied that the adsorption process was spontaneous and exothermic. Nano-biocomposite (HEC-GO/Fe-Zn) can be used as an adsorbent to remove water pollutants.

Nanoencapsulation and bioaccessibility of polyphenols of aqueous extracts from Bauhinia forficata link

Bauhinia forficata Link is a plant rich in polyphenols that has been used mainly for its hypoglycemic activity, which is related to its antioxidant and anti-inflammatory potential. However, the beneficial effect of these bioactive compounds is directly dependent on their bioaccessibility and bioavailability, requiring processing techniques that can improve and preserve their biological activities. This work aimed to obtain nanocapsulated extracts from the infusion (ESIN) and decoction (ESDC) of B. forficata Link leaves, by spray drying. The encapsulating agents used were maltodextrin and colloidal silicon dioxide. The nanocapsules were characterized by HPLC-PDA-ESI-IT-MS ⁿ , evaluated the bioaccessibility of polyphenols after simulated digestion and their antioxidant activity. Additionally, an extensive physicochemical characterization of the nanocapsulated extracts was carried out and their stability and technological parameters were evaluated. The ESIN and ESDC extracts had yields of 57.3 % and 62.7 %, with average nanocapsules sizes of 0.202 μm and 0.179 μm, low humidity and water activity (<0.5), powder density and proper flow properties (Hausner ratio ≤ 1.25; Carr index 18-19 %). Scanning electron microscopy showed a spherical and amorphous morphology and low viscosity, which may have favored the solubility profile. The phenolic compounds of the nanocapsules degraded after 400 °C, showing high thermal stability. The infrared spectra identified the presence of maltodextrin and phenolic compounds and that there were no reactions between them. Chromatography confirmed the presence of phenolic compounds, mainly flavonols and their O-glycosylated derivatives, as well as carbohydrates, probably maltodextrin. Simulated in vitro digestion showed that polyphenols and flavonoids from ESIN and ESDC nanocapsules were bioaccessible after the gastric phase (49.38 % and 64.17 % of polyphenols and 64.08 % and 36.61 % of flavonoids) and duodenal (52.68 % and 79.06 % of polyphenols and 13.24 % and 139.03 % of flavoids), with a variation from 52.27 % to 70.55 % of the antioxidant activity maintained, by the ORAC method, after gastric digestion and still 25 %, after duodenal. Therefore, the nanoencapsulation of extracts of B. forficata is a viable option for the preservation of their bioactive compounds, making them bioaccessible and with antioxidant activity, which make them suitable for incorporation into various nutraceutical formulations, such as capsules, tablets and sachets.

Ecofriendly and sustainable Sargassum spp.-based system for the removal of highly used drugs during the COVID-19 pandemic

Analgesic consumption increased significantly during the COVID-19 pandemic. A high concentration of this kind of drug is discarded in the urine, reaching the effluents of rivers, lakes, and seas. These medicines have brought serious problems for the flora and, especially, the ecosystems’ fauna. This paper presents the results of removing diclofenac, ibuprofen, and paracetamol in an aqueous solution, using Sargassum spp. from the Caribbean coast. The study consisted of mixing each drug in an aqueous solution with functionalized Sargassum spp in a container under constant agitation. Therefore, this work represents an alternative to solve two of the biggest problems in recent years; first, the reduction of the overpopulation of sargassum through its use for the remediation of the environment. Second is the removal of drug waste used excessively during the COVID-19 pandemic. Liquid samples of the solution were taken at intervals of 10 min and analyzed by fluorescence to determine the concentration of the drug.

The sorption capacity for diclofenac, ibuprofen, and paracetamol was 2.46, 2.08, and 1.41 μg/g, corresponding to 98 %, 84 %, and 54 % of removal, respectively. The removal of the three drugs was notably favored by increasing the temperature to 30 and 40 °C, reaching efficiencies close to 100 %. Moreover, the system maintains its effectiveness at various pH values. In addition, the Sargassum used can be reused for up to three cycles without reducing its removal capacity. The wide diversity of organic compounds favors the biosorption of drugs, removing them through various kinetic mechanisms. On the other hand, the Sargassum used in the drugs removal was analyzed by X-ray diffraction, FTIR spectroscopy, TGA analysis, and scanning electron microscopy before and after removal. The results showed an evident modification in the structure and morphology of the algae and demonstrated the presence of the biosorbed drugs. Therefore, this system is sustainable, simple, economical, environmentally friendly, highly efficient, and scalable at a domestic and industrial level that can be used for aquatic remediation environments.