Comparison of Cr(VI) adsorption and photocatalytic reduction efficiency using leonardite powder

Fabrication of Active Z-Scheme Sr2MgSi2O7: Eu2+, Dy3+/COF Photocatalyst for Round-the-Clock Efficient Removal of Total Cr

Photoreduction is recognized as a desirable treatment method for hexavalent chromium (Cr(VI)). However, it has been limited by the intermittent solar flux and limited light absorption. In this work, a novel Z-scheme photocatalyst combining a covalent organic framework (COF) with Eu2+, Dy3+ co-doped Sr2MgSi2O7 (Sr2MgSi2O7:Eu2+, Dy3+) is synthesized, which shows the high spectral conversion efficiency and works efficiently in both light irradiation and dark for Cr(VI) reduction. Sr2MgSi2O7:Eu2+, Dy3+ serves as both an electron transfer station and active sites for COF molecule activation, thus resulting in 100% photoreduction of Cr(VI) (50 mL, 10 mg/L) with high light stability and over 1 h dark activity. Moreover, the XPS and FT-IR analyses reveal the existence of functional groups (Si-OH on Sr2MgSi2O7:Eu2+, Dy3+, and -NH- on COFTP-TTA) on the composited catalyst as active sites to adsorb the resultant Cr(III) species, demonstrating a synergistic effect for total Cr removal. This work provides an alternative method for the design of a round-the-clock photocatalyst for Cr(VI) reduction, allowing a versatile solid surface activation for establishing a more energy efficient and robust photocatalysis process for Cr pollution cleaning.

The highly efficient photodegradation of 4-bromophenol by TiO2/g-C3N4 nano photocatalyst with LED visible light

Since traditional photocatalysts have suffered from higher charge carrier recombination and moderate photocatalytic efficiency, developing photocatalysts is crucial for water treatment objectives. Hence, the various ratios of TiO2 on g-C3N4 (CN) to form nano photocatalysts were synthesized by the solvothermal method. The 30%TiO2/CN showed the best performance to degradation and debromination of 4-bromophenol (4-BP) solution completely (kobs = 6.6 × 10-2 min-1) under visible light emitted by LED (420 nm) in 30 min. Remarkably, the photocatalyst showed superior stability and reusability, maintaining its efficiency after four cycles of 4-BP degradation. The dominant ROS participating in 4-BP degradation were ●O-2 and photogenerated holes (h+), as investigated by free radical scavenging tests. The optical properties analysis revealed that the introduction of TiO2 to the bulk CN decreases electron-hole recombination and improve photocatalytic performance by facilitating electrons transfer through the TiO2 nanoparticles in a chain. The findings of this study showed that the TiO2/CN photocatalyst is a promising catalyst for the degradation of 4-BP. It exhibits a higher rate constant and photocatalytic efficiency compared with previous studies conducted under visible light irradiation.

Enhancing photocatalytic reduction of Cr(VI) in water through morphological manipulation of g-C3N4 photocatalysts: A comparative study of 1D, 2D, and 3D structures

In this research, the dimensional catalysts of pure g-C3N4 photocatalysts (1D, 2D, and 3D) were investigated for the reduction of the highly toxic/carcinogenic Cr(VI) under visible light irradiation. The catalysts underwent explanation through various surface analysis techniques. According to the BET data, the specific surface area of the 3D catalyst was 1.3 and 7 times higher than those of the 2D and 1D CN catalysts, respectively. The 3D catalyst demonstrated superior performance, achieving an efficiency greater than 99% within 60 min under visible light irradiation in the presence of EDTA due to the abundance of active sites. The study also delved into the influence of factors such as the amount of EDTA-hole scavenger, pH, catalyst dosage, and temperature on the photocatalytic reduction of Cr(VI). Moreover, the 3D catalyst showed excellent reusability, maintaining an efficiency of more than 80% even after 10 cycles, and performed effectively in real water samples. The 3D CN catalyst, with its facile synthesis process, excellent visible light harvesting properties, high reduction efficiency that sustains over multiple cycles, and outstanding performance in real water samples, presents a significant advancement for practical applications in environmental remediation. This research contributes to a new understanding of developing efficient degradation methods for heavy metals in polluted water, highlighting the potential of 3D g-C3N4 catalysts in environmental cleanup efforts.

Efficient removal of Chromium(VI) from wastewater based on magnetic multiwalled carbon nanotubes coupled with deep eutectic solvents

Industrial wastewater containing heavy metal Cr(VI) seriously affects the health of organisms and may even lead to cancer. Developing efficient adsorbents that can quickly separate heavy metals is crucial for treating wastewater. In this study, magnetic multiwalled carbon nanotubes (MMWCNTs) with moderate particle size and abundant surface active sites were prepared by coating multiwalled carbon nanotubes with magnetic nanoparticles. The results of FTIR, XRD, TG, VSM, BET, and EDS showed MWCNTs completely encapsulated on the surface of the magnetic nanoparticles, with a particle size of approximately 30 nm. Oxygenated groups provided abundant surface active sites and formed numerous mesopores. The response surface methodology was used to optimize the adsorbent dose, adsorption contact time and adsorption temperature, and the removal rate of Cr(VI) was more than 95%. The quasi-second order kinetics and Freundlich adsorption isotherm model explained the adsorption process to Cr(VI). MMWCNTs interacted with Cr(VI) through electrostatic attraction, reduction reactions, complexation, and other means. The extensive hydrogen bonding of the green solvent deep eutectic solvent (DES) was employed to desorb the MMWCNTs and desorption rate exceed 90%. Even after five adsorption-regeneration cycles, the adsorbent maintained a high capacity. In conclusion, these novel MMWCNTs, as efficient adsorbents paired with DES desorption, hold broad potential for application in the treatment of Cr(VI)-contaminated wastewater.

Vermicompost and millicompost as a resource in sustainable agriculture in semiarid: decomposition, nutrient release, and microstructure under the action of nitrogen and organic-mineral fertilizers

With the expansion of organic agriculture, research is needed to indicate economically and ecologically viable fertilizer options, especially in semiarid regions, with low soil organic matter and nitrogen content. In the Brazilian semiarid region, vermicomposts are widely used by farmers and are scientifically investigated; however, there is no information for millicompost, a new type of organic compound that has shown very promising results in other regions. Thus, this study aimed to analyze the decomposition rate, nutrient release, and microstructure evaluation of vermicomposts from different sources and of millicompost produced from plant residues, with the application of mineral nitrogen-urea and organo-mineral fertilizer in the Brazilian semiarid region. The experimental design was a randomized block in a 4 × 3 factorial scheme, with four replicates; four organic composts (millicompost, commercial vermicompost, vermicompost from bovine manure, vermicompost from goat manure); and three types of fertilization (without fertilizer, with mineral-urea and organo-mineral fertilizer). The organic composts were decomposed using litterbags at the soil surface. The variable's decomposition rate and the nutrient release were evaluated at six-time intervals (0, 30, 60, 90, 120, and 150 days), and microstructure was evaluated at the beginning and the end of the experiment, with scanning electron microscopy (SEM). The highest decomposition was verified for commercial vermicompost rich in macro and micronutrients and with lower P contents. The lignin:N ratio and the initial P content were more important in the permanence of the organic compost in the field than the C:N ratio. Regardless of the organic composts, the use of urea as a mineral fertilizer stimulated decomposition more than the organo-mineral fertilizer. The initial composition of the nutrients was decisive in the dynamics of nutrient release, mass loss, and decomposition of C. There was no pattern in the release order of macronutrients. However, for the micronutrients, the release order was Cu > Fe > Mn, in all treatments. Microstructure analysis is a visual analysis where differences are detected through microphotographs and the biggest difference occurred with millicompost, which showed elongated fibers and fiber bundles, forming a relatively open structure characteristic of the presence of fulvic acid. However, the addition of organo-mineral fertilizer formed agglomerates in compacted micro-portions, helping the mineralization of C and N.

Quantifying the mitigating effect of organic matter on heavy metal availability in soils with different manure applications: A geochemical modelling study

Manure is one of the main sources of heavy metal (HM) pollution on farmlands. It has become the focus of global ecological research because of its potential threat to human health and the sustainability of food systems. Soil pH and organic matter are improved by manure and play pivotal roles in determining soil HM behavior. Geochemical modeling has been widely used to assess and predict the behavior of soil HMs; however, there remains a research gap in manure applications. In this study, a geochemical model (LeachXS) coupled with a pH-dependent leaching test with continuously simulations over a broad pH range was used to determine the effects and pollution risks of pig or cattle manure separate application on soil HMs distribution. Both pig and cattle manure applications led to soil pH reduction in alkaline soils and increased organic matter content. Pig manure application resulted in a potential 90.5-156.0 % increase in soil HM content. Cattle manure did not cause significant HM contamination. The leaching trend of soil HMs across treatments exhibited a V-shaped change, with the lowest concentration at pH = 7, gradually increasing toward strong acids and bases. The dissolved organic matter-bound HM content directly increased the HM availability, especially for Cu (up to 8.4 %) after pig manure application. However, more HMs (Cr, Cu, Zn, Ni) were in the particulate organic matter-bound state than in other solid phases (e.g., Fe-Al(hydr) oxides, clay minerals), which inhibited the HMs leaching by more than 19.3 % after cattle manure application. Despite these variations, high HM concentrations introduced by pig manure raised the soil contamination risk, potentially exceeding 40 times at pH ±1. When manure is returned to the field, reducing its HM content and mitigating possible pollution is necessary to realize the healthy and sustainable development of circular agriculture.

Enhanced photoreduction efficiency of Cr(VI) driven by visible light in a new Zr-based metal-organic framework modified by hydroxyl groups

While metal-organic framework (MOF) photocatalysts have demonstrated a unique Cr(VI) photoreduction capability in recent decades, their performance is still insufficient for practical applications because of their low Cr(VI) uptake and poor visible light response. To cope with these drawbacks, a new OH-modified Zr-based MOF, termed HCMUE-1, was successfully prepared via a solvothermal method in this work. The complete characterization of HCMUE-1 was performed through various techniques, including powder X-ray diffraction (PXRD), Raman spectroscopy, Fourier transform infrared (FT-IR), thermogravimetric analysis and differential scanning calorimetry (TGA-DSC), scanning electron microscopy combined with energy-dispersive X-ray (SEM-EDX), and X-ray photoelectron spectroscopy (XPS). The obtained data exhibited the excellent Cr(VI) photoreduction efficiency of HCMUE-1, reaching up to 98% after 90 min and almost 100% after 120 min under visible light illumination in a low acidic medium. Noteworthily, HCMUE-1 retained the same Cr(VI) removal rate for at least seven cycles without considerable loss. Further experimental investigations demonstrated that the structural stability and surface morphology of HCMUE-1 were retained after photoreduction. Moreover, the photocatalytic reduction mechanism of Cr(VI) to Cr(III) was interpreted through a series of systematic experimental measurements. These results indicate that HCMUE-1 possesses potential as an efficient photocatalyst for reducing toxic Cr(VI) species from wastewater in real-life conditions.

Novel insights into crystal violet dye adsorption onto various macroalgae: Comparative study, recyclability and overview of chromium (VI) removal

In this study, effective biomaterials were prepared from marine macroalgae, namely Fucus spiralis (F.S), Ulva intestinalis (U.I), and Corallina officinalis (C.O). The ability to adsorb the hazardous organic dye crystal violet (CV) was examined, revealing different adsorptive properties for the three algae. The removal of CV dye occurred onto only a homogeneous monolayer for F.S, and both a homogeneous monolayer and a heterogeneous multilayer for U.I and C.O algae. The predicted monolayer capacities at 25 °C were approximately 53 mg/g, 55 mg/g, and 97 mg/g for F.S, C.O, and U.I, respectively. The adsorption of CV dye on all the algae was found to follow a pseudo-second-order rate. Ulva intestinalis algae, as a potential adsorbent of CV dye, were also tested in the adsorption of inorganic substances and demonstrated significant efficiency in the removal of chromium (VI). The findings highlight various adsorption properties and the relevance of macroalgae for wastewater treatment applications.

Application of novel nanobubble-contained electrolyzed catalytic water to cleanup petroleum-hydrocarbon contaminated soils and groundwater: A pilot-scale and performance evaluation study

Soil and groundwater contamination caused by petroleum hydrocarbons is a severe environmental problem. In this study, a novel electrolyzed catalytic system (ECS) was developed to produce nanobubble-contained electrolyzed catalytic (NEC) water for the remediation of petroleum-hydrocarbon-contaminated soils and groundwater. The developed ECS applied high voltage (220 V) with direct current, and titanium electrodes coated with iridium dioxide were used in the system. The developed ECS prototype contained 21 electrode pairs (with a current density of 20 mA/cm2), which were connected in series to significantly enhance the hydroxyl radical production rate. Iron-copper hybrid oxide catalysts were laid between each electrode pair to improve the radical generation efficiency. The electron paramagnetic resonance (EPR) and Rhodamine B (RhB) methods were applied for the generated radical species and concentration determination. During the operation of the ECS, high concentrations of nanobubbles (nanobubble density = 3.7 × 109 particles/mL) were produced due to the occurrence of the cavitation mechanism. Because of the negative zeta potential and nano-scale characteristics of nanobubbles (mean diameter = 28 nm), the repelling force would prevent the occurrence of bubble aggregations and extend their lifetime in NEC water. The radicals produced after the bursting of the nanobubbles would be beneficial for the increase of the radical concentration and subsequent petroleum hydrocarbon oxidation. The highly oxidized NEC water (oxidation-reduction potential = 887 mV) could be produced with a radical concentration of 9.5 × 10-9 M. In the pilot-scale study, the prototype system was applied to clean up petroleum-hydrocarbon polluted soils at a diesel-oil spill site via an on-site slurry-phase soil washing process. The total petroleum hydrocarbon (TPH)-contaminated soils were excavated and treated with the NEC water in a slurry-phase reactor. Results show that up to 74.4% of TPH (initial concentration = 2846 mg/kg) could be removed from soils after four rounds of NEC water treatment (soil and NEC water ratio for each batch = 10 kg: 40 L and reaction time = 10 min). Within the petroleum-hydrocarbon plume, one remediation well (RW) and two monitor wells (located 1 m and 3 m downgradient of the RW) were installed along the groundwater flow direction. The produced NEC water was injected into the RW and the TPH concentrations in groundwater (initial concentrations = 12.3-15.2 mg/L) were assessed in these three wells. Compared to the control well, TPH concentrations in RW and MW1 dropped to below 0.4 and 2.1 mg/L after 6 m3 of NEC water injection in RW, respectively. Results from the pilot-scale study indicate that the NEC water could effectively remediate TPH-contaminated soils and groundwater without secondary pollution production. The main treatment mechanisms included (1) in situ chemical oxidation via produced radicals, (2) desorption of petroleum hydrocarbons from soil particles due to the dispersion of nanobubbles into soil pores, and (3) enhanced TPH oxidation due to produced radicals and energy after nanobubble bursting.

High-Efficiency Adsorption of Cr(VI) and Mn(VII) from Wastewater by a Two-Dimensional Copper-Based Metal-Organic Framework

Cr(VI) and Mn(VII) in industrial wastewater have certain toxicity, and they pose a threat to the environment and human health and safety. Metal-organic frameworks (MOFs) usually have rich adsorption sites and a large specific surface area. They can effectively adsorb Cr(VI) and Mn(VII) from wastewater. In this paper, a two-dimensional copper-based metal-organic framework, {[Cu·(4,4'-bpy)2·(H2O)]·2(NO3)·6(H2O)·(CH3OH)}n (1), is synthesized by hydrothermal synthesis. The structure of 1 is characterized by Fourier transform infrared (IR) spectroscopy, single-crystal X-ray diffraction, element analysis, and X-ray photoelectron spectroscopy (XPS). The results showed that 1 had a two-dimensional network structure, and the specific surface area of the nanostructure was 67.63 m2/g. The nanostructure of 1 could efficiently adsorb Cr(VI) and Mn(VII) from wastewater. The adsorption properties of Cr(VI) and Mn (VII) of 1 showed that the optimal concentration of both adsorbents was 0.2 g/L. It has good adsorption performance in the pH range 4-8. The adsorption performance is the best when pH is 7, which can reach 145 and 83 mg/g, respectively.

Optimization of the anaerobic fermentation process for phosphate release using food waste

Phosphorus (P) problem worries the whole world due to the increasing demand for finite and non-renewable natural phosphate resources and the inadequacy of sustainable phosphate production technologies. In this study, bio-acidification processes using waste sludge and food waste for simultaneous sustainable phosphate release and biogas production were investigated. Response surface methodology (RSM) was used for bio-acidification optimization. High performance was achieved with the addition of 10% FW and a temperature of 45 °C, which provided 5.30 pH and 371 mg/L P release for 10 days. A total of 196 mL of cumulative biogas was produced. Using food waste potentially reduces operating costs, eliminating the need for external chemical additions for pH control. Also, this approach offers benefits such as waste management, recovery of valuable resources, cost reduction, and environmental friendly.

Mn-Doped Spinel for Removing Cr(VI) from Aqueous Solutions: Adsorption Characteristics and Mechanisms

In this study, the manganese (Mn) was doped in the MnFe₂O₄ crystal by the solid-phase synthesis method. Under the optimum conditions (pH = 3), the max removal rate and adsorption quantity of Cr(VI) on MnFe₂O₄ adsorbent obtain under pH = 3 were 92.54% and 5.813 mg/g, respectively. The DFT calculation results indicated that the adsorption energy (E_ads) between HCrO₄^- and MnFe₂O₄ is -215.2 KJ/mol. The Cr(VI) is mainly adsorbed on the Mn atoms via chemical bonds in the form of HCrO₄^-. The adsorption of Mn on the MnFe₂O₄ surface belonged to chemisorption and conformed to the Pseudo-second-order equation. The mechanism investigation indicated that the Mn in MnFe₂O₄ has an excellent enhancement effect on the Cr(VI) removal process. The roles of Mn in the Cr(VI) removal process included two parts, providing adsorbing sites and being reductant. Firstly, the Cr(VI) is adsorbed onto the MnFe₂O₄ via chemisorption. The Mn in MnFe₂O₄ can form ionic bonds with the O atoms of HCrO₄^-/CrO₄^2-, thus providing the firm adsorbing sites for the Cr(VI). Subsequently, the dissolved Mn(II) can reduce Cr(VI) to Cr(III). The disproportionation of oxidized Mn(III) produced Mn(II), causing Mn(II) to continue to participate in the Cr(VI) reduction. Finally, the reduced Cr(III) is deposited on the MnFe₂O₄ surface in the form of Cr(OH)₃ colloids, which can be separated by magnetic separation.

A novel insight into the microwave induced catalytic reduction mechanism in aqueous Cr(VI) removal over ZnFe2O4 catalyst

Aqueous Cr(VI) pollution is an emerging environmental issue. Herein, a sphere-like ZnFe₂O₄ catalyst with a size of ∼430 nm was prepared by a solvothermal method, by which the aqueous Cr(VI) in a 50 mL solution with concentration of 50 mg/L was completely removed after 10 min-microwave (MW) irradiation. "Surface temperature visualization" tests and COMSOL simulations showed that the surface temperature of the as-prepared ZnFe₂O₄ catalysts could be as high as > 1000 °C only after 300 s MW irradiation, and the work function calculations and scavenging experiments demonstrated that the excited electrons derived by the "hot spots" effect of the ZnFe₂O₄ catalysts reduced the Cr(VI) to Cr(III). Kinetic reaction process of the reduction of *Cr₂O₇^2- to *CrO₃H₃ over the ZnFe₂O₄ catalysts was clarified by using DFT calculation, and the results indicated that *Cr₂O₇^2- adsorbed on the Fe atoms was more easily to be reduced, and that Fe atoms played more significant roles than the Zn and O atoms in ZnFe₂O₄ catalysts. The present study not only proves that the MW induced ZnFe₂O₄ catalytic reduction was promising for ultrafast remediation of toxic Cr(VI), but also provides a new insight into the corresponding mechanism.

BiVO4-Deposited MIL-101-NH2 for Efficient Photocatalytic Elimination of Cr(VI)

In this study, a flower-like BiVO₄/MIL-101-NH₂ composite is synthesized by a facile and surfactant-free process. The -COO^--Bi³⁺ ionic bond construction was conductive to enhance the interface affinity between BiVO₄ and MIL-101-NH₂. Due to the highly efficient light capture and sufficient electron traps induced by oxygen vacancies and the formation of a heterostructure, the improved separation and transportation rates of charge carriers are realized. In addition, the MIL-101-NH₂/BiVO₄ composite is favorable for Cr(VI) photocatalytic removal (91.2%). Moreover, FNBV-3 (Fe/Bi = 0.25) also exhibited an excellent reusability after five cycles.

WITHDRAWN: Heavy metal ions and dyes removal from aqueous solution using Aloevera-based biosorbent: A systematic review

This article has been withdrawn: please see Elsevier Policy on Article Withdrawal (http://www.elsevier.com/locate/withdrawalpolicy). This article has been withdrawn at the request of the authors, editor and publisher. The publisher regrets that an error occurred which led to the premature publication of this paper. The publisher apologizes to the readers for this unfortunate erro

Preparation of hydrochar bio-based catalyst for fenton process in dye-containing wastewater treatment

The use of synthetic dyes in the textile industry pollutes a huge amount of water. Thus, wastewater discharged from many textile companies to the receiving environment without being treated causes serious environmental and human health problems. The development of new techniques has become imperative. In this study, it was aimed to remove anionic dye (RR180) and cationic dye (BR18) by Fenton-like and adsorption process with hydrochars obtained from laurel leaves and watermelon peels. In the comparison of the adsorption and Fenton-like processes used in the dye removal of the produced bio-based materials, the Fenton-like process was selected in order to enhance the highest removal efficiency. The effects of various operating factors such as solution pH, amount of catalysts, hydrogen peroxide (H₂O₂) concentration, and initial dye concentration were evaluated on both dyes removal. The experimental results demonstrated that 99.8% RR180 dye and 98.8% BR18 dye removal efficiency were observed for an initial dye concentration of 100 mg/L with an adsorbent concentration of 1 g/L, H₂O₂ concentration of 15 μL/L, and optimum pH at the end of 60 min of reaction time. It was observed that an increase in initial dye concentration caused to decrease the dye removal efficiency. The optimum pH for the highest RR180 and BR18 dye removal was 4 and 6, respectively. It was observed that the increase in H₂O₂ concentration in the solution also decreased the dye removal efficiency. It turned out that catalysts obtained from hydrochars are an effective process for the high removal performance of cationic and anionic dyes.

Comparison of constructed wetland performance coupled with aeration and tubesettler for pharmaceutical compound removal from hospital wastewater

Pharmaceutical compounds being able to alter, retard, and enhance metabolism has gained attention in recent time as emerging pollutant. However, hospitals which are part of every urban landscape have yet to gain attention in terms of its hospital wastewater treatment to inhibit pharmaceutical compounds from reaching environment. Hence this study evaluated performance of constructed wetland in combination with tubesettler and aeration based on removal efficiency and ecological risk assessment (HQ). The removal efficiency of constructed wetland with plantation was higher by 31% (paracetamol), 102% (ibuprofen), 46%, (carbamazepine), 57% (lorazepam), 54% (erythromycin), 31% (ciprofloxacin) and 20% (simvastatin) against constructed wetland without plantation. Constructed wetland with aeration efficiency increased for paracetamol, ibuprofen, carbamazepine, lorazepam, erythromycin, ciprofloxacin, and simvastatin removal efficiency were higher by 58%, 130%, 52%, 79%, 107%, 57%, and 29% respectively. In constructed wetland with plantation, removal efficiency was higher by 20% (paracetamol), 13% (ibuprofen), 4% (carbamazepine), 14% (lorazepam), 34% (erythromycin), 19% (ciprofloxacin) and 7% (simvastatin). High ecological risk was observed for algae, invertebrate and fish with hazard quotient values in range of 2.5-484, 10-631 and 1-78 respectively. This study concludes that if space is the limitation at hospitals aeration with constructed wetland can be adopted. If space is available, constructed wetland with tubesettler is suitable, economic and environmentally friendly option. Future research works can focus on evaluating other processes combination with constructed wetland.

Synthesis of ZnO immobilized on recycled polyethylene terephtalate for sonocatalytic removal of Cr(VI) from synthetic, drinking waters and electroplating wastewater

In this study, Cr(VI) was removed sonocatalytically by the zinc oxide nanoparticle coated with polyethylene terephthalate (PET) fabricated through a facile co-precipitation method. The crystal structure, functional groups on the surface, morphology, surface composition and oxidation states of the nanomaterials were investigated by XRD, FTIR, SEM, EDX and XPS techniques. Environmental parameters including solution pH, catalyst dose, hexavalent chromium concentration, H₂O₂ content, purging gases, organic compounds and type and anions strength on the sonotocatalytic removal of Cr(VI) were also investigated. Additionally, the contribution of each process, reusability, Cr(VI) reduction from actual water and electroplating wastewater were evaluated. Under the optimal conditions, [Cr(VI)]₀=20 mg/L, nanocomposite loading=1.6 g/L and pH=5, 99.92% of Cr(VI) was removed within 60 min. By increaing, Cr(VI) concentration (5-50 mg/L), k_obs decreased to values between 0.1498 and 0.0063 min^-1 and the calculated electrical energy per order (E_Eo) increased from 148.68 to 3535.24 kWh.m^-3, respectively. The presence of purging gases, organic compounds and ionic strength negatively affected Cr(VI) reduction. Examination of radical scavengers showed that the most active radicals in Cr(VI) removal were O₂^•- and h⁺. The removal of the Cr(VI) using the US/ZnO-PET method (99.92%) was higher than that of the US/ZnO method (70.78%). The catalyst activity was well maintained up to eight consecutive cycles. In addition, the removal efficiency was approximately 72.23 and 68.55% for drinking water and real electroplating wastewater samples, respectively. The results of toxicity in the sonotocatalytic removal of Cr(VI) by Daphnia magna showed LC₅₀ and toxicity unit (TU) 48 h, which was equal to 81.46 and 1.227 vol percent.

An integrated process for wet scrubber wastewater treatment using electrooxidation and pressure-driven membrane filtration

In this study, the electrooxidation (EO) and membrane processes were used for chemical oxygen demand (COD) and total phenol (TPh) removal from wet scrubber wastewater (WSW). EO experiments were carried out using Al, Fe, SS, Ti, graphite, active carbon cloth electrodes and Box-Behnken design were used for optimization of maximum COD and TPh removal efficiency. Moreover, membrane filtration experiments were conducted to EO process using nanofiltration (NF270) and reverse osmosis membranes (SW30 and BW30). The maximum COD (55%) and TPh (50%) removal efficiency was achieved at pH of 8, 150 A/m² current density, and 180 min reaction time in EO process. Membrane filtration results showed that COD removal efficiency was the highest for SW30 membrane (95.18%) compared to BW30 (91.15%) and NF270 (80.11%) membranes. TPh removal efficiency in the NF270, BW30, and SW30 membranes was 27.08%, 96.06%, and 98.02%, respectively. The effect of microbial cell viability of the raw and treated wet scrubber wastewater after electrooxidation and membrane filtration was also investigated using E. coli. In addition to these, biofilm inhibition of the raw wet scrubber wastewater and the treated WSW after EO and membrane filtration were tested and the highest biofilm inhibition was found as 76.43% and 72.58% against S. aureus and P. aeruginosa, respectively, in 1/20 diluted samples of the raw WSW. This study suggests that the integrated process using EO and pressure-driven membrane methods are an efficient strategy for COD and TPh removal from WSW.

Saiz P, Reizabal A, Wuttke S, Celaya-Azcoaga L, Valverde A, Fernández de Luis R. A State-of-the-Art of Metal-Organic Frameworks for Chromium Photoreduction vs. Photocatalytic Water Remediation

Hexavalent chromium (Cr(VI)) is a highly mobile cancerogenic and teratogenic heavy metal ion. Among the varied technologies applied today to address chromium water pollution, photocatalysis offers a rapid reduction of Cr(VI) to the less toxic Cr(III). In contrast to classic photocatalysts, Metal-Organic frameworks (MOFs) are porous semiconductors that can couple the Cr(VI) to Cr(III) photoreduction to the chromium species immobilization. In this minireview, we wish to discuss and analyze the state-of-the-art of MOFs for Cr(VI) detoxification and contextualizing it to the most recent advances and strategies of MOFs for photocatalysis purposes. The minireview has been structured in three sections: (i) a detailed discussion of the specific experimental techniques employed to characterize MOF photocatalysts, (ii) a description and identification of the key characteristics of MOFs for Cr(VI) photoreduction, and (iii) an outlook and perspective section in order to identify future trends.

Iron-loaded leonardite powder for Fenton oxidation of Reactive Red 180 dye removal

Fenton oxidation is an effective and valuable method for wastewater treatment. To inhibit environmental impacts and increase overall reaction efficiencies, it is important to develop advanced catalysts. This paper illustrates an experimental study on the elimination of RR180 dye from synthetic aqueous solutions with raw leonardite and different iron-loaded leonardite powders, Fe(0)-loaded leonardite, and Fe(II)-loaded leonardite. The effect of solution pH (2.0-6.0), catalyst amount (0.10-1.5 g/L), H₂O₂ concentration (10-50 µL/L), and dye concentration (10-30 ppm) was tested to achieve maximum color removal efficiency using the three catalysts. At pH = 2, color removal efficiencies were higher and more suitable. Initial experiments showed the advantage of using Fe(II)-loaded leonardite on using Fe(0)-loaded leonardite. Fe(II)-loaded leonardite catalyst was the most efficient in RR180 color removal compared to the other tested reagents. Color removal in function of solution pH did not decrease much when Fe(II)-loaded leonardite was used (100 to 96%) when pH was increased from 2.0 to 6.0. In the other hand, dye removal has been significantly affected in the case of using raw leonardite, Fe(0)-loaded leonardite (93 to 0%), and (100 to 13%) in the same pH range, respectively. At optimum experimental conditions, catalyst amount: 0.75 g/L for Fe(II) and Fe(0)-loaded leonardite and 1.5 g/L for raw leonardite; dye concentration: 10 ppm; solution pH: 2.0; H₂O₂ concentration: 50 µL/L; volume: 100 mL and reaction time: 60 min, RR180 dye removal efficiencies were 91%, 100%, and 100% by raw leonardite, Fe(0)-loaded leonardite and Fe(II)-loaded leonardite, respectively. The stability and reusability of the tested catalyst was investigated up to ten cycles. The experimental results revealed that both Fe(0)-loaded leonardite and Fe(II)-loaded leonardite can be used in Fenton reaction up to four cycles without decreasing their efficiency in RR180 color removal. The characterization of the catalysts was established using scanning electron microscope with energy dispersive X-ray spectroscopy (SEM-EDX). The synthesized catalyst can be used at large scale in any textile industry to effectively remove dyes resulting in high elimination rates at the optimal determined and studied conditions.

Activated carbon-chitosan based adsorbent for the efficient removal of the emerging contaminant diclofenac: Synthesis, characterization and phytotoxicity studies

The rise in pharmaceutical pollutants due to their unregulated discharge in pharmaceutical wastewater has landed them as emerging contaminants that would gradually affect the aquatic ecosystem and human life. The current study emphasizes the adsorptive elimination of one such emerging pharmaceutical pollutant, i.e., Diclofenac (DIF), using a synthesized adsorbent vis. Activated carbon-chitosan beads (ACCB). The morphological and physicochemical properties of the prepared adsorbent, ACCB and its interaction with the DIF species were investigated. Process parameters influencing the adsorptive interactions between ACCB and DIF were optimised. DIF was efficiently adsorbed at optimised initial DIF pH of 6.0 and ACCB dosage of 1.5 mg/mL at an incubation temperature of 40 °C. Freundlich isotherm model showed the best fit (R² = 0.98) with the experimental data to conclude that the adsorbent surface is heterogenous, promoting multilayer adsorption. As depicted from the Langmuir isotherm model, the maximum theoretical adsorption capacity was 99.29 mg/g. The seed toxicity assay confirmed the efficacy of ACCB in the adsorptive removal of DIF species from aqueous setups, making the post-treated solution fit enough for seed germination.

Facile preparation of visible light-sensitive layered g-C3N4 for photocatalytic removal of organic pollutants

The graphite-phase carbon nitride (g-C₃N₄) photocatalytic materials were prepared by one-step calcination method to degrade methylene blue (MB) and potassium butyl xanthate (PBX) under visible light irradiation. The prepared g-C₃N₄ photocatalytic materials were investigated in detail by various characterizations, and the experiments showed that the graphitic phase carbon nitride photocatalytic materials were successfully prepared by the one-step calcination method. The material possesses excellent optical properties and strong visible light absorption, thus achieving photocatalytic degradation of MB and PBX. The catalyst dosage, pH, the initial concentration of pollutants have important effects on photocatalytic activity of MB and PBX. The photocatalytic degradation efficiency was 98.99% for MB and 96.83% for PBX under the optimal conditions (catalyst dosage, initial pollutant concentration and pH value were 500 mg L^-1, 20 mg L^-1 and 7, respevtively). The photocatalytic mechanisms on MB and PBX were elucidated. ·OH was the key specie for MB, while ·O₂^- was the key specie for PBX. This study advances the development of photocatalytic technology for mineral wastewater.

Treatment of real printing and packaging wastewater by combination of coagulation with Fenton and photo-Fenton processes

Printing and packaging process wastewater (PPPW) with high flow rates causes severe damage to the environment due to high organic pollution (3830.0 mg O₂/L of COD and 813.6 mg/L of TOC) and turbidity (9110 NTU). This study examined the efficiencies of coagulation, Fenton, and photo-Fenton procedures, and their combinations in the treatment of PPPW. The three inorganic salts (FeCl₃, Al₂(SO₄)₃, and Fe₂(SO₄)₃) were used in a wide range of pH (2.5-10) as a coagulant, and FeCl₃ was chosen as the optimum coagulant. The 71.3% of TOC removal and the decreasing of turbidity up to 5.8 NTU were obtained at 0.5 g/L FeCl₃ and pH of 6.0. Then, Fenton and photo-Fenton processes were applied to the effluent of the coagulation process. The Fenton process engaged the TOC removal efficiencies up to 85.2% in the presence of 7.350 g/L iron catalysts and 36.0 mL/L H₂O₂. The combined coagulation and Fenton process is a promising way to decrease the COD up to 119 mg O₂/L, meeting the wastewater discharge standards of COD (200 mg O₂/L) in Turkey. However, adding UV sources to the Fenton process showed a little bit of engagement (only %1.4 extra removal). When evaluated for PPPW, it is seen that the usage of combined coagulation and the Fenton process is an important treatment alternative. Furthermore, Zeta potential measurements and size exclusion chromatography were used to understand the removal mechanism.

Synthesis of two different zinc oxide nanoflowers and comparison of antioxidant and photocatalytic activity

Nanoflowers are a newly developed class of nanoparticles that show flower-like structures and attract much attention due to their simple preparation methods, high stability, and increased efficiency. The aim of the study is to investigate a strong alternative to reduce the severity of infection and increase the treatment of wastewater by exhibiting biofilm inhibition in medical and environmental applications of the ZnO-NFs with two different shapes. ZnO-NFs were synthesized by two different processes hydrothermal method (named ZnO-NF1) and the precipitation method (named ZnO-NF2). ZnO-NFs produced by two different synthesis methods were compared for the photocatalytic and antioxidant efficiency. The effects of Reactive Red 180 (RR180) and Basic Red 18 (BR18) dyes concentration, photocatalyst amount, and reaction time were investigated on dye removal efficiency for photocatalytic experiments. The color was completely removed for 25 mg/L BR18 and RR180 dyes for 75 min and 90 min, respectively, using 1.5 g/L photocatalyst amount using ZnO-NF1. However, 59.18% dye removal efficiency was obtained for 90 min by using a 1.5 g/L ZnO-NF2 photocatalyst for 25 mg/L BR18 dye removal, while a dye removal efficiency of 90.00% was detected for 90 min using 2 g/L ZnO-NF2 for 25 mg/L RR180 dye. Then, comparison of general properties such as antibacterial, antibiofilm, microbial cell viability, DNA fragmentation, antioxidant activities, and antimicrobial photodynamic therapy of ZnO-NFs were investigated. The antioxidant activity of ZnO-NF2 was found to be higher than ZnO-NF1 at each concentration (82.32% and 87.18% for ZnO-NF1 and ZnO-NF2, respectively, at 200 mg/mL).

Excess sludge biochar facilitates persulfate activation for highly efficient tetracycline removal

This study proposed a novel advanced oxidation system to treat metal and antibiotic pollution in water simultaneously. Meanwhile, the enhancement effect of absorbed metal pollution on the activation of persulfate in the system was also investigated. As the most widely used and polluting material, tetracycline (TC) and metal Fe were used as the pollutant models. In this study, a carbonaceous material (BC) was prepared from excess sludge and then combined with the persulfate system (Fe/BC/PS). It was found that the best biochar was obtained when the pyrolysis temperature reached 500 °C (BC500), with the specific surface area of 39.712 m²/g. Combining it with 300 mg/L PS, the removal rate of 120 mg/L TC reached 70.6%. Moreover, the sludge biochar itself possessed numerous reaction sites and good defective structure, which provided a perfect reaction site for the variable metals absorbed by BC. They accelerated electron conduction greatly, which led to the activation of PS very active and generating far more active radicals than normal. In addition, it also proposed the rational pathway and potential mechanism of TC degradation based on the degradation intermediates. This study has a high reference value for resource utilization of sewage sludge and antibiotics removal from water.

Efficient Removal of Eriochrome Black T (EBT) Dye and Chromium (Cr) by Hydrotalcite-Derived Mg-Ca-Al Mixed Metal Oxide Composite

Eriochrome Black T (EBT) and chromium (Cr) are considered to be potential pollutants due to their toxicity and severe impact on the environment. In the current study, hydrotalcite-derived Mg-Ca-Al-LDO mixed metal oxide composite was prepared using a conventional co-precipitation method and explored in terms of the removal of Cr and EBT dye from aqueous solution in a batch mode adsorption process. The prepared Mg-Ca-Al-LDH, Mg-Ca-Al-LDO and spent Mg-Ca-Al-LDO adsorbents were characterized to propose the adsorption mechanism. Different adsorption parameters were examined, such as adsorbent dosage, initial concentration, pH, reaction temperature and contact time. The EBT adsorption kinetic results matched strongly with the pseudo-second-order model for both Cr (R2 = 0.991) and EBT (R2 = 0.999). The Langmuir isotherm model exhibited a maximum adsorption capacity of 65.5 mg/g and 150.3 mg/g for Cr and EBT, respectively. The structure and morphology results obtained after Cr and EBT dye adsorption reveal that the adsorption mechanism is associated with electrostatic interactions and surface complexation of Cr and EBT dye with Mg-Ca-Al-LDO surface functional groups. Moreover, more than 84% of the initial adsorption capacity of EBT and Cr can be achieved on the Mg-Ca-Al-LDO surface after five adsorption/desorption cycles. Finally, the Mg-Ca-Al-LDO mixed metal oxide composite can be potentially used as a cost-effective adsorbent for wastewater treatment processes.

Remediation of heavy metal polluted waters using activated carbon from lignocellulosic biomass: An update of recent trends

The use of a cheap and effective adsorption approach based on biomass-activated carbon (AC) to remediate heavy metal contamination is clearly desirable for developing countries that are economically disadvantaged yet have abundant biomass. Therefore, this review provides an update of recent works utilizing biomass waste-AC to adsorb commonly-encountered adsorbates like Cr, Pb, Cu, Cd, Hg, and As. Various biomass wastes were employed in synthesizing AC via two-steps processing; oxygen-free carbonization followed by activation. In recent works related to the activation step, the microwave technique is growing in popularity compared to the more conventional physical/chemical activation method because the microwave technique can ensure a more uniform energy distribution in the solid adsorbent, resulting in enhanced surface area. Nonetheless, chemical activation is still generally preferred for its ease of operation, lower cost, and shorter preparation time. Several mechanisms related to heavy metal adsorption on biomass wastes-AC were also discussed in detail, such as (i) - physical adsorption/deposition of metals, (ii) - ion-exchange between protonated oxygen-containing functional groups (-OH, -COOH) and divalent metal cations (M²⁺), (iii) - electrostatic interaction between oppositely-charged ions, (iv) - surface complexation between functional groups (-OH, O^2-, -CO-NH-, and -COOH) and heavy metal ions/complexes, and (v) - precipitation/co-precipitation technique. Additionally, key parameters affecting the adsorption performance were scrutinized. In general, this review offers a comprehensive insight into the production of AC from lignocellulosic biomass and its application in treating heavy metals-polluted water, showing that biomass-originated AC could bring great benefits to the environment, economy, and sustainability.

Synthesis of silver nanoparticles from red and green parts of the pistachio hulls and their various in-vitro biological activities

In this study, synthesis of silver nanoparticles (AgNPs) was carried out utilizing the red and green parts of the pistachio hulls then their several biological activities were investigated. The DPPH (2,2-diphenyl-1-picryl-hydrazyl-hydrate) activities of the AgNPs synthesized from red pistachio hulls extracts (PhR-AgNPs) and green pistachio hulls extracts (PhG-AgNPs) were investigated. The DPPH scavenging capability at 200 mg/L concentration of PhR-AgNPs was around 93.01% however PhG-AgNPs displayed 91.00%. The synthesized PhR-AgNPs and PhG-AgNPs acted on the E. coli plasmid DNA, causing its complete degradation and exhibiting effective chemical nuclease activity. Furthermore, PhR-AgNPs and PhG-AgNPs showed quite good antimicrobial activity against the studied strains with a range of the minimum inhibition concentration (MIC) of 8-16 mg/L. Moreover, it was observed that both pistachio hulls coated with AgNPs were highly effective in inhibiting the biofilm generation studied strains. Moreover, PhR-AgNP and PhG-AgNP displayed a completely inhibition effect on cellular viability of E. coli with 100% at 125 mg/L.

Leonardite powder as an efficient adsorbent for cationic and anionic dyes

This paper aims to investigate the uses of leonardite powder (LP) as an effective adsorbent for the removal of basic red 18 (BR18) and reactive red 180 (RR180) dyes. LP was characterized using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), Zeta potential, Brunauer-Emmett-Teller (BET) analysis, Fourier transform infrared spectroscopy (FTIR), and X-ray fluorescence (XRF). The adsorption process was assessed based on pH, size and the amount of the adsorbent, BR18 and RR180 concentration, and the contact time. BR18 dye was completely adsorbed onto the LP (the removal efficiency equals 100%) after 45 min at the optimum condition (original pH [6.5], the particle size of 45 μm, the adsorbent dose of 0.25 g/L, and the initial concentration of 10 mg/L). For RR180, the maximum removal efficiency (74%) was obtained when 1 g/L LP with 45 um size was added to an RR180 solution of 10 mg/L concentration. Temkin isotherm was used to explain the adsorption of BR18. In contrast, RR180 adsorption was described by the Freundlich model. The adsorptions of both dyes followed the pseudo-second-order kinetics. The reusability of the LP was assessed. For BR18, the efficiency decreased to 96% in the second cycle and reached 42% in the fifth cycle. In RR180, LP was not able to be reused efficiently. As a result, the LP ability for BR18 removal is higher than the RR180 in terms of uptake and reusability. PRACTITIONER POINTS: BR18 and RR180 dyes elimination was carried out with leonardite powder (LP). The maximum removal efficiencies for BR18 and RR180 were 100% and 74%, respectively. The LP ability for BR18 removal is higher than the RR180 in terms of uptake and reusability.