Effects of ionic strength and particle size on transport of microplastic and humic acid in porous media

Current research status on the distribution and transport of micro(nano)plastics in hyporheic zones and groundwater

Micro(nano)plastics, as an emerging environmental pollutant, are gradually discovered in hyporheic zones and groundwater worldwide. Recent studies have focused on the origin and spatial/temporal distribution of micro(nano)plastics in regional groundwater, together with the influence of their properties and effects of environmental factors on their transport. However, the transport of micro(nano)plastics in the whole hyporheic zone-groundwater system and the behavior of co-existing substances still lack a complete theoretical interpretation. To provide systematic theoretical support for that, this review summarizes the current pollution status of micro(nano)plastics in the hyporheic zone-groundwater system, provides a comprehensive introduction of their sources and fate, and classifies the transport mechanisms into mechanical transport, physicochemical transport and biological processes assisted transport from the perspectives of mechanical stress, physicochemical reactions, and bioturbation, respectively. Ultimately, this review proposes to advance the understanding of the multi-dimensional hydrosphere transport of micro(nano)plastics centered on groundwater, the microorganisms-mediated synergistic transformation and co-transport involving the intertidal circulation. Overall, this review systematically dissects the presence and transport cycles of micro(nano)plastics within the hyporheic zone-groundwater system and proposes prospects for future studies based on the limitations of current studies.

Impact of freeze-thaw cycles on the remobilization behaviors of microplastics in natural soils

Freeze-thaw (FT) cycle would greatly influence the fate of plastic particles (one of emerging contaminants with great concerns) in soils, yet its impacts and mechanisms remain unclear. The vertical migration/release behaviors of plastic particles (with diameters of 0.2 μm and 1 μm) in two natural soils and one model soil (i.e. quartz sand) without/with FT treatments (1 and 3 cycles) were examined. Owing to the presence of Fe/Al oxide minerals, finer pore structure, and uneven surfaces of natural soils, the breakthrough ratio of plastics in two natural soils was over 25% lower than in quartz sand. However, regardless of porous media type, FT processes (increasing cycles) significantly promoted the remobilization of plastics initially retained in three media during the subsequent water flushing processes. Via theoretical calculation, tracer experiments, and visible chamber experiments, the mechanisms driving plastics release from natural soils subjected to FT treatments during the water elution processes were determined to be different from those from pure quartz sand. The change of sand local configuration (the rearrangement of local sand pore spaces) during FT process mainly drove to plastics released from quartz sand columns. While the alteration in local soil configuration, the formation of preferential pathways, and increased release of soil particles contributed to plastics remobilization from soil columns subjected to FT. Clearly, FT processes significantly increased the vertical migration of plastics in soils potentially to groundwater, enhancing environmental risks of plastics.

Recent advances and factors affecting the adsorption of nano/microplastics by magnetic biochar

The increase in nano/microplastics (NPs/MPs) from various everyday products entering aquatic environments highlights the urgent need to develop mitigation strategies. Biochar (BC), known for its excellent adsorption capabilities, can effectively target various harmful organic and inorganic pollutants. However, traditional methods involving powdered BC necessitate centrifugation and filtration, which can lead to the desorption of pollutants and subsequent secondary pollution. Magnetic biochar (MBC) offers a solution that facilitates straightforward and rapid separation from water through magnetic techniques. This review provides the latest insights into the progress made in MBC applications for the adsorption of NPs/MPs. This review further discusses how external factors such as pH, ionic strength, temperature, competing ions, dissolved organic matter, aging time, and particle size impact the MBC adsorption efficiency of MPs. The use of machine learning (ML) for optimizing the design and properties of BC materials is also briefly addressed. Finally, this review addresses existing challenges and future research directions aimed at improving the large-scale application of MBC for NPs/MPs removal.

Experimental and mathematical investigation of cotransport of clay and microplastics in saturated porous media

Microplastics in the subsurface cause groundwater contamination, thereby posing potential risks to human health and the ecosystem. Clay particles are ubiquitous in the subsurface and can interact and alter the transport behavior of microplastics. Hence, it is essential to understand the effect of clays on the transport behavior of microplastics to estimate the groundwater contamination potential. This study investigated the individual transport and cotransport of clay and microplastics under different pore-water velocities and sand types in saturated porous media through column experiments and mathematical modeling. Copresence of suspended microplastics retarded the transport of clay due to the preferential attachment of clay over microplastics on grain surfaces and the formation of clay-microplastic heteroaggregates which have a greater retention in sand than free clay and free microplastics. However, in contrast, cotransport with clay enhanced the transport of microplastics due to the lower affinity of microplastics than clay for deposition on grain surfaces and the lesser mass fraction of microplastics than clay in the heteroaggregates. The cotransport of clay and microplastics was successfully simulated using a two-way coupled model, which accounted for the retention of free clay and free microplastics in the sand, kinetics of clay-microplastics heteroaggregation, and heteroaggregate retention in the sand. The rates of heteroaggregation and heteroaggregate retention in sand decreased with increasing velocity and grain size, resulting in increased transport of clay and microplastics.

Modeling microplastic transport through porous media: Challenges arising from dynamic transport behavior

Modelling microplastic transport through porous media, such as soils and aquifers, is an emerging research topic, where existing hydrogeological models for (reactive) solute and colloid transport have shown limited effectiveness thus far. This perspective article draws upon recent literature to provide a brief overview of key microplastic transport processes, with emphases on less well-understood processes, to propose potential research directions for efficiently modeling microplastic transport through the porous environment. Microplastics are particulate matter with distinct physicochemical properties. Biogeochemical processes and physical interactions with the surrounding environment cause microplastic properties such as material density, geometry, chemical composition, and DLVO interaction parameters to change dynamically, through complex webs of interactions and feedbacks that dynamically affect transport behavior. Furthermore, microplastic material densities, which cluster around that of water, distinguish microplastics from other colloids, with impactful consequences that are often underappreciated. For example, (near-)neutral material densities cause microplastic transport behavior to be highly sensitive to spatio-temporally varying environmental conditions. The dynamic nature of microplastic properties implies that at environmentally relevant large spatio-temporal scales, the complex transport behavior may be effectively intractable to direct physical modeling. Therefore, efficient modeling may require integrating reduced-complexity physics-constrained models, with stochastic or statistical analyses, supported by extensive environmental data.

Pore-Scale Visualized Transport and Retention of Fibrous and Fragmental Microplastics in Porous Media under Various Surfactant Conditions

For advancing current knowledge on the transport of microplastics (MPs) in the environment, this study used a real-time pore-scale visualization and quantitative system to examine the motions and mobility of fibrous and fragmental MPs under various surfactant (AEO, CTAC, and AES) and electrolyte conditions. The videos showed that fibrous MPs formed tangles through entanglement, which moved in an axial direction aligned with the flow streamline. Both fibrous and fragmental MPs showed suspended movement as well as surface movement (e.g., sliding, rolling, and saltating) in the porous media. Some deposited fibrous MPs showed flexible deformation due to shear flow. Compared to fragmental MPs, fibrous MPs showed lower mobility due to the tendency to deposit and clog the porous media. The mobility of fragmental MPs was enhanced in the presence of AEO but remained relatively unchanged with AES. In the presence of CTAC, the mobility of fragmental MPs was slightly inhibited under low ionic strength (IS) conditions but remarkably enhanced under high IS conditions. However, the mobility of fibrous MPs was largely unaffected by the surfactants. Both the numerical model and FDLVO calculations effectively described the transport and deposition of MPs in porous media.

Effects of polystyrene microplastics on the distribution behaviors and mechanisms of metalloid As(III) and As(V) on pipe scales in drinking water distribution systems

Pipe scales have long been considered the primary adsorption medium for trace heavy metals in drinking water distribution systems (DWDSs). Microplastics (MPs) potentially affect the distribution of metalloid arsenic (As) pollutants in DWDSs. Herein, the accumulation behaviors of As(Ⅲ) and As(V) on pipe scales and polystyrene microplastics (PSMPs) under different water conditions were studied. Additionally, As(Ⅲ) and As(V) accumulation behaviors on pipe scales coexisting with PSMPs were investigated. Results showed that pipe scales played a key role in the accumulation of As (pipe scales = 1.08-4.80 mg/g > PSMPs = 0.02-3.38 mg/g). The adsorption amount of As(Ⅲ) on PSMPs was higher than that of As(V). The addition of PSMPs promoted the accumulation of As(Ⅲ) on pipe scales at pH = 3-8 while inhibiting the accumulation of As(V) on pipe scales at pH = 3-10 due to the competitive adsorption. The oxidation of As(III) and the reduction of As(V) occurred during the accumulation of As(Ⅲ) and As(V) on pipe scales. Notably, PSMPs accumulated on pipe scales were beneficial to the oxidation of As(Ⅲ), potentially reducing the As-related risks. Overall, our results provide new insights into the hazards posed by MPs in DWDSs.

Insights into the controlling factors of the transport of tire wear particles in saturated porous media: The facilitative role of aging and fulvic acid

The widespread distribution and potential adverse effects of tire wear particles (TWPs) on soil and groundwater quality pose a growing environmental concern. This study investigated the transport behavior of TWPs in saturated porous media and elucidated the underlying mechanisms influenced by environmental factors. Additionally, the effects of key environmental factors, such as aging, ionic strength, cation species, medium type, and natural organic matter (NOM), on the transport of TWPs were evaluated. The results showed that aging processes simulated through O3 and UV irradiation altered the physicochemical properties of TWPs, increased the mobility of TWPs at low ionic strengths. However, the high ionic strengths and the presence of Ca2+ significantly inhibited the mobility of TWPs due to enhanced aggregation. The transport mechanism of the original and aged TWPs shifted from blocking to ripening under favorable retention conditions (i.e., high ionic strengths, divalent cations, and fine sands). Interestingly, the presence of fulvic acid (FA) inhibited the ripening of the three TWPs, significantly promoting their transport through a spatial site resistance mechanism. The two-site kinetic attachment model (TSKAM), extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory, and colloid filtration theory (CFT) were applied to describe the transport behavior of the TWPs. The study provided a comprehensive understanding of the transport behavior of TWPs in groundwater environments, highlighting the environmental risks associated with their widespread distribution.

Interfacial interactions between colloidal polystyrene microplastics and Cu in aqueous solution and saturated porous media: Model fitting and mechanism analysis

Microplastic (MP) and heavy metal pollution have received much attention. Few researches have been carried out on the influence of the interaction between MPs and heavy metals on their transport in saturated porous media, which concerns their fate. Therefore, the interaction mechanisms between colloidal polystyrene microplastics (PSMPs) and Cu were first carried out by applying batch adsorption experiments. Subsequently, the transport and retention of PSMPs and Cu in saturated porous media was explored through column experiments. The interaction process between PSMPs and Cu was further investigated using density functional theory (DFT) calculations. Findings demonstrated that PSMPs had strong adsorption capacity for Cu ((60.07 ± 2.57) mg g-1 at pH 7 and ionic strength 0 M) and the adsorption process was chemically dominated, non-uniform, and endothermic. The O-containing functional groups on PSMP surfaces showed essential roles in Cu adsorption, and the adsorption process mainly contained electrostatic and complexation interactions. In column experiments, Cu could inhibit PSMP transport by the cation bridging effect and changing the electrical properties of glass beads, while PSMPs may facilitate Cu transport through the carrying effect. These findings confirmed that interfacial interactions between MPs and Cu could influence their transport in saturated porous media directly, providing great environmental significance.

Migration of natural organic matter and Pseudomonas fluorescens-associated polystyrene on natural substrates in aquatic environments

This study investigated the migration behavior of microplastics (MPs) covered with natural organic matter (NOM) and biofilm on three substrates (silica, Pseudomonas fluorescent and Pseudomonas aeruginosa biofilms) in various ionic strengths, focusing on the alterations in surface properties based on surface energy theory that affected their deposition and release processes. Peptone and Pseudomonas fluorescens were employed to generate NOM-attached and biofilm-coated polystyrene (PS) (NOM-PS and Bio-PS). NOM-PS and Bio-PS both exhibited different surface properties, as increased roughness and particle sizes, more hydrophilic surfaces and altered zeta potentials which increased with ionic strength. Although the deposition of NOM-PS on biofilms were enhanced by higher ionic strengths and the addition of Ca2+, while Bio-PS deposited less on biofilms and more on the silica surface. Both types exhibited diffusion-driven adsorption on the silica surface, with Bio-PS also engaging in synergistic and competitive interactions on biofilm surfaces. Release tests revealed that NOM-PS and Bio-PS were prone to release from silica than from biofilms. The Extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory furtherly demonstrated that mid-range electrostatic (EL) repulsion had significantly impacts on NOM-PS deposition, and structural properties of extracellular polymeric substances (EPS) and substrate could affect Bio-PS migration.

Cotransport of 6PPD-Q and pristine/aged microplastics in porous media: An insight based on transport forms and mechanisms

The environmental fate and risks of microplastics (MPs) and their associated contaminants have attracted increasing concern in recent years. In this study, the cotransport of six kinds of pristine and aged MPs and the antiager ozonation product N-(1,3-dimethylbutyl)-N'-phenyl-p-phenylenediamine-quinone (6PPD-Q) were investigated via a series of batch and transport experiments, and characteristic analysis (e.g., SEM, FTIR and XPS). Generally, pristine MPs exhibit higher adsorption ability than aged MPs due to the hydrophobic interaction. The 6PPD-Q usually exhibited both free moving and bond-MPs moving during transport process in presence of MPs, but none free 6PPD-Q was detected in presence of pristine PP MPs. The mobility of 6PPD-Q was generally facilitated in presence of MPs by bond-MPs moving due to the hydrogen bonding, halogen bonding, π-π interaction (the maximum total mass recovery of 84.11%), which efficiency was influenced with the combined effect of adsorption ability and mobility of MPs. The pristine PVC MPs showed highest facilitation on 6PPD-Q transport. The retained 6PPD-Q in porous media also was released by various MPs with different mass recovery ranged from 15.72% to 56.26% via surface moving of MPs around porous media. Both the dissolved and retained 6PPD-Q decreased the MPs mobility with the minimum mass recovery of 34.02%. Findings from this study contribute to the prediction and assessment of the combined risks of MPs and 6PPD-Q.

Microplastics in ecosystems: Critical review of occurrence, distribution, toxicity, fate, transport, and advances in experimental and computational studies in surface and subsurface water

Microplastics (MPs), particles under 5 mm, pervade water, soil, sediment, and air due to increased plastic production and improper disposal, posing global environmental and health risks. Examining their distribution, quantities, fate, and transport is crucial for effective management. Several studies have explored MPs' sources, distribution, transport, and biological impacts, primarily focusing on the marine environment. However, there is a need for a comprehensive review of all environmental systems together for enhanced pollution control. This review critically examines the occurrence, distribution, fate, and transport of MPs in the following environments: freshwater, marine, and terrestrial ecosystems. The concentration of MPs is highly variable in the environment, ranging from negligible to significant amounts (0.003-519.223 items/liter in water and 0-18,000 items/kg dry weight sediment, respectively). Predominantly, these MPs manifest as fibers and fragments, with primary polymer types including polypropylene, polystyrene, polyethylene, and polyethylene terephthalate. A complex interplay of natural and anthropogenic actions, including wastewater treatment plant discharges, precipitation, stormwater runoff, inadequate plastic waste management, and biosolid applications, influences MPs' presence and distribution. Our critical synthesis of existing literature underscores the significance of factors such as wind, water flow rates, settling velocities, wave characteristics, plastic morphology, density, and size in determining MPs' transport dynamics in surface and subsurface waters. Furthermore, this review identifies research gaps, both in experimental and simulation, and outlines pivotal avenues for future exploration in the realm of MPs.

Transport of polystyrene microplastics in bare and iron oxide-coated quartz sand: Effects of ionic strength, humic acid, and co-existing graphene oxide

This research explored the effects of widely utilized nanomaterial graphene oxide (GO) and organic matter humic acid (HA) on the transport of microplastics under different ionic solution strengths in bare sand and iron oxide-coated sand. The results found transport of polystyrene microplastics (PS) did not respond to the presence of HA in sand that contains large amounts of iron oxide. Compared to bare quartz sand, ionic strength had little effect: <20 % of PS passed through Fe sand columns. There was a significant promotion of PS transport in the presence of GO, however, which can be attributed to the increased surface electronegativity of PS and steric hindrance. Moreover, GO combined with HA significantly promoted the transport of PS in the Fe sand, and transport further increased when the concentration of HA increased from 5 to 10 mg/L. Interestingly, the degree of this increase exactly corresponded to the change in the surface charge of the microplastics, demonstrating that electrostatic interaction dominated the PS transport. Further results indicated that co-existing pollutants had significant impacts on the transport of microplastics under various conditions by altering the surface characteristics of the plastic particles and the spatial steric hindrance within porous media. This research will offer insights into predicting the transport and fate of microplastics in complex environments.

Placental and fetal enrichment of microplastics from disposable paper cups: implications for metabolic and reproductive health during pregnancy

The disposable paper cups (DPCs) release millions of microplastics (MPs) when used for hot beverages. However, the tissue-specific deposition and toxic effects of MPs and associated toxins remain largely unexplored, especially at daily consumption levels. We administered MPs and associated toxins extracted from leading brand DPCs to pregnant mice, revealing dose-responsive harmful effects on fetal development and maternal physiology. MPs were detected in all 13 examined tissues, with preferred depositions in the fetus, placenta, kidney, spleen, lung, and heart, contributing to impaired phenotypes. Brain tissues had the smallest MPs (90.35 % < 10 µm). A dose-responsive shift in the cecal microbiome from Firmicutes to Bacteroidetes was observed, coupled with enhanced biosynthesis of microbial fatty acids. A moderate consumption of 3.3 cups daily was sufficient to alter the cecal microbiome, global metabolic functions, and immune health, as reflected by tissue-specific transcriptomic analyses in maternal blood, placenta, and mammary glands, leading to neurodegenerative and miscarriage risks. Gene-based benchmark dose framework analysis suggested a safe exposure limit of 2 to 4 cups/day in pregnant mice. Our results highlight tissue-specific accumulation and metabolic and reproductive toxicities in mice at DPC consumption levels presumed non-hazardous, with potential health implications for pregnant women and fetuses.

Effect of particle density on microplastics transport in artificial and natural porous media

The occurrence and persistence of microplastics (MPs) in natural environments are of increasing concern. Along with this, the transport of MPs in sediments has been investigated mainly focusing on the effect of plastic size and shape, media size effect, and solution chemistry. Yet, the influence of particle density is only partially understood. Therefore, column experiments on the transport of variably buoyant MPs in saturated natural sediments and glass beads were conducted, and transport parameters were quantified using a two-site kinetic transport model with a depth-dependent blocking function (the amount of retained MPs does not decrease at a constant rate with increasing depth, the majority of MPs were retained near the column inlet). Neutral, sinking, and buoyant MPs within the same size range were selected, with stable water isotope applied as conservative tracer to explore water and MP movement in the tested sediments. The results showed that 95.5 ± 1.4% of sinking MPs remained in columns packed with gravel, followed by buoyant and neutral MPs, thus indicating that particle density does affect MP mobility. Similar recovered amounts of MPs were found in columns packed with glass beads, indicating that tested sediment types do not affect the deposition behavior of MPs. The breakthrough curves of MPs were accurately described by the selected model. However, the simulated retention profiles overestimated the observed MP amount in layers closest to the column inlet. The coupled experimental and modeled results suggest an enhanced retention of sinking MPs, while neutrally and buoyant MPs exhibit a higher mobility in comparison. Thus, neutral or buoyant MPs can potentially pose a higher contamination risk to subsurface porous media environments compared to sinking MPs. Discrepancies between observed and simulated retention profiles indicate that future model development is needed for advancing the MP deposition as affected by particle density.

Comparative study of polystyrene microplastic transport behavior in three different filter media: Quartz sand, zeolite, and anthracite

Microplastics (MPs) are emerging contaminants that are attracting increasing interest from researchers, and the safety of drinking water is greatly affected by their transportation during filtration. Polystyrene (PS) was selected as a representative MPs, and three filter media (quartz sand, zeolite, and anthracite) commonly found in water plants were used. The retention patterns of PS-MPs by various filter media under various background water quality conditions were methodically investigated with the aid of DLVO theory and colloidal filtration theory. The results show that the different structures and elemental compositions of the three filter media cause them to exhibit different surface roughnesses and surface potentials. A greater surface roughness of the filter media can provide more deposition sites for PS-MPs, and the greater surface roughness of zeolite and anthracite significantly enhances their ability to inhibit the migration of PS-MPs compared with that of quartz sand. However, surface roughness is not the only factor affecting the migration of MPs. The lower absolute value of the surface potential of anthracite causes the DLVO energy between it and PS-MPs to be significantly lower than that between zeolite and PS-MPs, which results in stronger retention of PS-MPs by anthracite, which has a lower surface roughness, than zeolite, which has a higher surface roughness. The transport of PS-MPs in the medium is affected by the combination of the surface roughness of the filter media and the DLVO energy. Under the same operating conditions, the retention efficiencies of the three filter materials for PS-MPs followed the order of quartz sand < zeolite < anthracite. Additionally, the conditions of the solution markedly influenced the transport ability of PS-MPs within the simulated filter column. The transport PS-MPs in the simulated filter column decreased with increasing solution ionic strength and cation valence. Naturally, dissolved organic matter promoted the transfer of PS-MPs in the filter layer, and humic acid had a much stronger facilitating impact than fulvic acid. The study findings might offer helpful insight for improving the ability of filter units ability to retain MPs.

Effects of arsenic on the transport and attachment of microplastics in porous media

Understanding the impact of arsenic (As(III), inorganic pollutant widely present in natural environments) on microplastics (MPs, one type of emerging contaminants) mobility is essential to predict MPs fate and distribution in soil-groundwater systems, yet relevant research is lacking. This study explored the effects of As(III) copresent in suspensions (0.05, 0.5, and 5 mg/L) on MPs transport/attachment behaviors in porous media containing varied water contents (θ = 100 %, 90 %, and 60 %) under different ionic strengths (5, 10, and 50 mM NaCl) and flow rates (2, 4, and 8 m/day). Despite solution ionic strengths, flow rates, porous media water contents, sizes, and surface charges of MPs, with coexisting humic acid, and in actual water samples, As(III) of three concentrations increased MPs transport in quartz sand and natural sandy soil. The increased electrostatic repulsion between MPs and sand caused by the altered MPs surface charge via the adsorption of As(III) together with steric repulsion from As(III) in solution contributed to the promoted MPs mobility in porous media. The occupying attachment sites by As(III) partially contributed to the increased mobility of MPs with negative surface charge in porous media. Clearly, As(III) coexisting in suspensions would enhance MPs transport in porous media, increasing MPs environment risks.

Microplastics/nanoplastics in porous media: Key factors controlling their transport and retention behaviors

Till now, microplastics/nano-plastics(M/NPs) have received a lot of attention as emerging contaminant. As a typical but complex porous medium, soil is not only a large reservoir of M/NPs but also a gateway for M/NPs to enter groundwater. Therefore, the review of the factors controlling the transport behavior of M/NPs in porous media can provide important guidance for the risk assessment of M/NPs in soil and groundwater. In this study, the key factors controlling the transport behavior of M/NPs in porous media are systematically divided into three groups: (1) nature of M/NPs affecting M/NPs transport in porous media, (2) nature of flow affecting M/NPs transport in porous media, (3) nature of porous media affecting M/NPs transport. In each group, the specific control factors for M/NPs transport in porous media are discussed in detail. In addition to the above factors, some substances (colloids or pollutants) present in natural porous media (such as soil or sediments) will co-transport with M/NPs and affect its mobility. According to the different properties of co-transported substances, the mechanism of promoting or inhibiting the migration behavior of M/NPs in porous media was discussed. Finally, the limitations and future research directions of M/NPs transport in porous media are pointed out. This review can provide a useful reference for predicting the transport of M/NPs in natural porous media.

Properties of biochar colloids and behaviors in the soil environment: Influencing the migration of heavy metals

Biochar pyrolyzed by biomass shows excellent application prospects for heavy metal (HM) remediation, but a part of biochar can be inevitably broken into micro- and nano-sized biochar colloids (BCs) under biological and physicochemical actions in soil. BCs derived in the process of remediation have rough surface, rich elemental species and contents, and multiple functional groups, which are similar to biochar. However, BCs have some unique colloidal properties because of their micro and nano scale size. Due to these properties, BCs exhibit strong mobilities in the soil environment, and the mobilities may be influenced by a combination of colloidal properties of BCs and environmental factors including soil colloids and other soil environmental conditions. In addition, BCs may have affinity effects on HMs through electrostatic adsorption, ion exchange, surface complexation, precipitation/co-precipitation, and redox because of the properties such as large specific surface area, and rich oxygen-containing functional groups and minerals on the surface. This review summarizes the physicochemical and migratory properties of BCs, and the internal and external factors affecting the migration of BCs in the soil environment, and the possible effects of BCs on HMs are high-lighted. This review provides a theoretical basis for the optimization of soil contaminated with HMs after remediation using biochar. Notably, the innovative idea that BCs may influence the presence of HMs in soil needs to be further confirmed by more targeted detection and analysis methods in future studies to prevent the possible environmental toxicities of the lateral and vertical diffusion of HM caused by BCs in soil.

Facilitated transport of toluene and naphthalene with humic acid in high- and low-permeability systems: Role of ionic strength and cationic type

The occurrence of colloids on pollutants transport in groundwater has attracted more attention. However, the research on the regulation mechanism of colloids on combined pollutants transport in heterogeneous aquifers is limited. In this study, a series of tank experiments were conducted to systematically investigate the effects of ionic strength, and cation type on humic acid (HA) facilitated transport of toluene (TOL), and naphthalene (NAP) in high- and low-permeability systems. The results showed that HA facilitated pollutants transport in low Na+ solution. In Ca2+ solution, the presence of HA hindered pollutants transport, and the inhibition increased with the increase of ionic strength. Both in Na+ solution and low Ca2+ solution, the influence of heterogeneous structure on pollutant transport played a dominant role, and TOL and NAP had a greater transport potential in the high permeability zone (HPZ) due to the preferential flow. Whereas, deposition of HA aggregates, and electrostatic attractive interaction had negative effects on transport than groundwater flow in high Ca2+ solution. Pollutants were prone to accumulate at the bottom of the HPZ, and the top of the low permeability zone (LPZ). These new findings provide insights into the mechanism of colloids influence on the pollutants transport in heterogenous aquifer.

Competitive adsorption behaviors and mechanisms of Cd, Ni, and Cu by biochar when coexisting with microplastics under single, binary, and ternary systems

In this study, the effects of coexistence with microplastics and co-ageing with the soil on adsorption behaviors and mechanisms of biochar for heavy metals were investigated. Adsorption experiments of Cd, Ni, and Cu by microplastics, biochar, and their combination were conducted in single, binary, and ternary systems. The results indicated that the heavy metal adsorption by microplastics was ranked as Ni > Cd > Cu, which increased with decreasing particle size, and the adsorption capacity of microplastics was enhanced after dry-wet and freeze-thaw ageing. Biochar preferentially adsorbed Cd in the single system, while the maximum adsorption of Cu was observed in the binary and ternary systems due to the minimizing impact of competition on the Cu adsorption by biochar. The heavy metal adsorption by the combination of microplastics and biochar was less than that by single biochar, and the smaller the particle size of microplastics, the greater the negative effects on heavy metal adsorption. Coexistence with microplastics reduced Cd adsorption of biochar by 0.72 %-50.35 %, Ni adsorption by 1.17 %-30.43 %, and Cu adsorption by 5.78 %-47.88 %, respectively. Moreover, coexistence with microplastics exacerbated the adverse impacts of competition on biochar adsorption for heavy metals. The contribution percentages of biochar mineral mechanisms for heavy metal adsorption were ranked as Cu > Cd > Ni. When coexisting with microplastics or after ageing, the mineral mechanisms of heavy metal adsorption by biochar significantly decreased. This study investigated the competitive adsorption behaviors and mechanisms of heavy metals by biochar when coexisting with microplastics, which highlighted that the application of biochar for the remediation of heavy metal pollution should be concerned with the impacts of microplastics.

Effect of NaNO3, NH4Cl and urea on the fate and transformation of various typical microplastics in porous media

Understanding the transport behaviors of microplastics (MPs) in porous media is crucial in controlling MPs pollution. Given nitrogen is one of the most important nutrients in soil and groundwater systems, unclearness of the transport behaviors of microplastics (MPs) under various nitrogen conditions may inhibit the acknowledgment of MPs fate. For this reason, this study innovatively investigates the transport characteristics of four kinds of typical MPs (PVC MPs, PMMA MPs, PET MPs, and PP MPs) under various NaNO3, NH4Cl and urea conditions via column experiments numerical models. The FTIR and XPS analysis were conducted to excavate the transform of MPs. The MPs mobility was generally reduced with the increasing nitrogen concentrations. The polarity and density properties of different MPs played combined roles in transport under similar conditions. Compared to NO3-, NH4+ may neutralize the negative charge of MPs and then restrain their transport in porous media. Urea may coat the surface of MPs and promote the mobility, however, increasing concentrations of urea may result in the interattraction between MPs and porous media via hydrogen-bond and π-π interaction. PET MPs and PP MPs showed barely transform during transport under the tested conditions. Particularly, the chlorines on PVC MPs could react with the amide on urea and produce amidogen, which may improve PVC MPs transport. The N-H and C-N bond also generated on PMMA MPs in presence of urea also may enhance the mobility.

Nano- and micro-plastic transport in soil and groundwater environments: Sources, behaviors, theories, and models

With the increasing use of plastics, nano- and micro-plastic (NMP) pollution has become a hot topic in the scientific community. Ubiquitous NMPs, as emerging contaminants, are becoming a global issue owing to their persistence and potential toxicity. Compared with studies of marine and freshwater environments, investigations into the sources, transport properties, and fate of NMPs in soil and groundwater environments remain at a primary stage. Hence, the promotion of such research is critically important. Here, we integrate existing information and recent advancements to compile a comprehensive evaluation of the sources and transport properties of NMPs in soil and groundwater environments. We first provide a systematic description of the various sources and transport behaviors of NMPs. We then discuss the theories (e.g., clean-bed filtration and Derjaguin-Landau-Verwey-Overbeek theories) and models (e.g., single-site and dual-site kinetic retention and transport models) of NMP transport through saturated porous media. Finally, we outline the potential limitations of current research and suggest directions for future research. Overall, this review intends to assimilate and outline current knowledge and provide a useful reference frame to determine the sources and transport properties of NMPs in soil and groundwater environments.

Microplastic pollution in the groundwater under a bedrock island in the South China sea

Groundwater is the only freshwater resource on islands. Research on microplastic pollution in groundwater on islands is scarce. This study is the first to explore microplastic pollution in the groundwater under a bedrock island (Dawanshan Island) located in the South China Sea. The influence of hydrogeological factors on the distribution, source, and ageing features of microplastics in the groundwater were investigated. Despite the small scale of industrial and agricultural activities on the island, the amount of microplastics in the groundwater ranged from 34 to 64 particles/L, with over 80% of the microplastics being polyester fibres with diameters smaller than 2 mm, which is comparable to those in coastal cities. These microplastics were originated from inland plastic usage, rather than from the surrounding sea, which was confirmed by the lack of seawater intrusion on the island. Owing to the low permeability of granite, microplastics were mainly distributed in the water of the loose layer of porous sediment, and their quantity decreased with depth. In addition, the abundance of microplastics in pore groundwater increased with an increase in the velocity of groundwater flow. The severity of microplastic pollution in the groundwater increased with an increase and decrease in the content of total dissolved solids and dissolved oxygen, respectively. The microplastics originated from plastic waste disposed of on the island, rather than from seawater intrusion. Also, through groundwater infiltration into exposed soil at recharge areas, artificial wells at residential areas, and water exchange with surface water at valley areas. Microplastics buried in the groundwater aged faster along the migration path of the groundwater. These microplastics threaten the safety of people and plants on the island through exposure resulting from the extraction of groundwater for irrigation, while they endanger marine life through submarine groundwater discharge.

Ethanol-diluted turbidimetry method for rapid and accurate quantification of low-density microplastics in synthetic samples

Retention and transport behaviours of microplastics (MPs) and their associated pollutants in porous media are of great concern. The homogeneity of the studied MPs in artificially controlled lab-scale studies makes rapid and accurate MP quantification feasible. In this study, an economical ethanol-diluted turbidimetry method for polypropylene (PP) and polyethylene (PE) MPs was developed. With ethanol dilution, the MP dispersion system exhibited an excellent suspension performance. Strong linear relationships were observed between MP concentrations and turbidities in both low (<1.3 mg L-1) and high (<170 mg L-1) MP concentration ranges. Solution density and MP agglomeration governed the MP suspension performance. For low surface tension and high molecular mass, the addition of ethanol decreased the contact angles of PP-MPs with solutions from 81.73 to 15.5°, and consequently improved the MP suspension performance. The suspension system was optimised to an ethanol/water (v/v) ratio of 3:2 and 4:1 for PP- and PE-MPs, when the slopes of standard curves were determined to be 1.252 and 0.471 with the recovery of 100.54 ± 3.09% and 103.19 ± 1.66%, and the limit of detection and quantification values of 0.025 and 0.082 mg L-1, and 0.060 and 0.201 mg L-1, respectively. Solution pH, salinity, and dissolved organic matter in the selected range induced acceptable fluctuations in the MP recovery and matrix effect values. The Derjaguin-Landau-Verwey-Overbeek (DLVO) energy barriers were calculated to be > 20 kT, indicating excellent tolerance to the solution matrix. Additionally, applications in real water samples were validated to demonstrate the potential of the developed method.

Stability of arsenic(Ⅲ, Ⅴ) in galvanized steel pipe scales coexisting with colloidal polystyrene microplastics under drinking water conditions

The stability of metalloid arsenic (As(Ⅲ)) and As(V) in corrosion scales of drinking water distribution systems (DWDS) is closely related to drinking water safety. The effects of colloidal microplastics entering the DWDS on the stability of As(Ⅲ) and As(V) have not been understood. This study investigated the migration and transformation behaviors of As (Ⅲ) and As(V) in the galvanized steel pipe scales employing speciation simulation and sequential extraction methods. The stability of As(Ⅲ) and As(V) in the pipe scales coexisting with colloidal polystyrene microplastics (CPMPs) under drinking water conditions was studied for the first time from the release behaviors and form distributions. Finally, the optimum water quality conditions for As(Ⅲ) and As(V) fixation were summarized. The existing forms of As(Ⅲ) and As(V) under different pH conditions, the competitive action of anions, and the hydrolysis of cations all would significantly affect the stability of As(Ⅲ) and As(V). Sequential extraction method results revealed that the content of As fractions increased in different forms after the pipe scales adsorbed As(Ⅲ) and As(V). The contents of As and iron (Fe) in the form of residual fractions increased in the presence of CPMPs. The effect of three cations on the stability of As(Ⅲ) and As(V) was Fe³⁺ > Zn²⁺ > Ca²⁺. Neutral to weak alkalescence, proper Cl^- and cation concentrations were conducive to the fixation of As in DWDS. Notably, the presence of CPMPs could increase the stability of As(Ⅲ) and As(V) in corrosion scales, thus reducing the risk of metalloid As release in DWDS.