Development of molecularly imprinted polymer based phase boundaries for sensors design (review)

A novel electropolymerized molecularly imprinted dual-mode sensor for bisphenol AF detection in pond mud

Recently, bisphenol AF (BPAF) as most commonly used bisphenol A analogs had the increasing higher level in the environment with unknown risks. Herein, a synchronous dual-mode sensor had been established based on differential pulse voltammetry (DPV) and electrochemiluminescence (ECL) for the detection of BPAF in pond mud. Firstly, the sensing molecularly imprinted polymer (MIP) films were prepared by electrochemical polymerization procedure with 3,4-ethoxylene dioxy thiophene (EDOT) as the functional monomer, BPAF as the template molecule and MXene as the supporting electrolyte. Due to unique characters of PEDOT and MXene, the constructed MIP films were stable and highly conductive. Meanwhile, zinc-doped bismuth sulfide quantum dots (Zn-Bi2S3 QDs) were synthesized as a nano-emitter to generate strong ECL signals in the MIP film. In the sensing process, a pulsed voltage applied to the PEDOT/MXene MIP film to generate both DPV and ECL signals for simultaneous dual-mode detection. Additionally, the liquid-liquid extraction with deep eutectic solvent (menthol: octanol 1:1) was used for the pre-concentration of the BPAF in the pond mud. Based on the sensing system, the ECL and DPV response showed the good linear relationships with the concentration of BPAF with the ranges of 0.01 μM-50 μM and 0.1 μM-50 μM and the detection limits of 0.0060 μM and 0.059 μM, respectively.

A molecularly imprinted electrochemical aptasensor-based dual recognition elements for selective detection of dexamethasone

In this work, a novel molecularly imprinted electrochemical aptasensor (MIEAS) was developed for highly selective detection of dexamethasone (Dex) in natural water environment. Gold nanoparticles (AuNPs) modified by nitrogen doped molybdenum carbide-graphene (N-Mo2C-Gr) were employed as the supports, where N-Mo2C-Gr improved the conductivity of the electrode and provided a larger specific surface area to polymerize more active substances. Using Dex as template molecule, o-phenylenediamine (o-PD) as the chemical functional monomer and aptamer as the biofunctional monomer, a molecularly imprinted polymer (MIP) membrane with Dex specific recognition sites was formed by electropolymerization. Due to the synergistic effect of MIP and aptamers, the as-prepared MIEAS exhibited a decent linear relationship to Dex detection within a relatively wide range of 10-13 - 10-5 M, and the detection limit was 1.79 × 10-14 M. The recovery in actual water and tablet samples is satisfactory, which confirms the potential application prospects of this sensor in the determination of Dex.

Application of Biosensors and Biomimetic Sensors in Dairy Products Testing

This article summarizes the applications of biosensors and biomimetic sensors in the detection of residues in dairy products. Biosensors utilize biological molecules such as enzymes or antibodies to detect residual substances in dairy products, demonstrating high specificity and sensitivity. Biomimetic sensors, inspired by biosensors, use synthetic materials to mimic biological sensing mechanisms, enhancing stability and reproducibility. Both sensor types have achieved significant success in detecting pesticide residues, veterinary drugs, bacteria, and other contaminants in dairy products. The applications of biological and biomimetic sensors not only improve the efficiency of residue detection in dairy products but also have the potential to reduce the time and cost of traditional methods. Their specificity and high sensitivity make them powerful tools in the dairy industry, thus contributing to ensuring the quality and safety of dairy products and meeting the growing consumer demands for health and food safety.

Highly selective and sensitive molecularly imprinted sensors for the electrochemical assay of quercetin in methanol extracts of Rubus sanctus and Fragaria vesca

Quercetin (QUE) is a powerful antioxidant and one of the common phenolic compounds found in plants, vegetables, and fruits, which has shown many pharmacological activities. The complex nature of the matrix in which QUE is found and its importance and potential uses in diverse applications force the researchers to develop selective and sensitive sensors. In the present work, a novel molecularly imprinted polymer (MIP)-based electrochemical sensor was fabricated for the selective and sensitive determination of the QUE in plant extracts and food supplements. Tryptophan methacrylate (TrpMA) was chosen as the functional monomer, whereas the photopolymerization (PP) method was applied using a glassy carbon electrode (GCE). Electrochemical and morphological characterizations of the developed sensor (TrpMA@QUE/MIP-GCE) were performed using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM). The linear range of the developed sensor was determined to be in the range of 1.0-25 pM, while the limit of detection (LOD) was calculated to be 0.235 pM. In conclusion, The TrpMA@QUE/MIP-GCE sensor might be classified as a promising platform for selective and sensitive determination of QUE not only in plant extracts but also in commercial food supplements because of its reliability, reproducibility, repeatability, stability, and fast response time.

Magnetic molecularly imprinted polymers using ternary deep eutectic solvent as novel functional monomer for hydroxytyrosol separation

In this work, magnetic molecularly imprinted polymers (MIPs) for specific recognition of Hydroxytyrosol (HT) were designed by vinyl-modified magnetic particles (Fe3O4@SiO2@VTEOs) as carrier, ternary deep eutectic solvent (DES) as functional monomer, while ethylene glycol dimethacrylate (EGDMA) as crosslinker. The optimum amount of DES was obtained by adsorption experiments (molar ratio, caffeic acid: choline chloride: formic acid = 1:6:3) which were 140 μL in total. Under the optimized amount of DES, the maximum adsorption capacity of the MIPs particles was 42.43 mg g-1, which was superior to non-imprinted polymer (4.64 mg g-1) and the imprinting factor (IF) is 9.10. Syringin and Oleuropicrin were used as two reference molecules to test the selectivity of the DES-MIPs particles. The adsorption capacity of HT was 40.11 mg g-1. Three repeated experiments show that the polymer has high stability and repeatability (RSD = 5.50).

In situ detection of dopamine in single living cells by molecularly imprinted polymer-functionalized nanoelectrodes

In situ detection of dopamine (DA) at single-cell level is critical for exploring neurotransmitter-related biological processes and diseases. However, the low content of DA and a variety of distractors with similar oxidation potentials as DA in cells brought great challenges. Here, a sensitive and specific electrochemical nanosensor was proposed for in situ detection of DA in single living cells based on nanodiamond (ND) and molecularly imprinted polymer (MIP)-functionalized carbon fiber nanoelectrode (ND/MIP/CFNE). Due to its excellent electrocatalytic property, ND was modified to the surface of CFNE based on amide bonding. Compared with bare CFNE, ND-modified CFNE can enhance oxidation currents of DA by about 4-fold, improving signal-to-noise ratio and detection sensitivity. MIP was further electropolymerized on the surface of nanoelectrodes to achieve specific capture and recognition of DA, which could avoid the interference of complex matrix and analogs in cells. Taking advantage of the precise positioning capability of a single-cell analyzer and micromanipulator, ND/MIP/CFNE could be precisely inserted into different locations of single cells and monitor oxidation signal of DA. The concentration of DA in the cytoplasm of single pheochromocytoma (PC12) cell was measured to be about 0.4 μM, providing a sensitive and powerful method for single-cell detection. Furthermore, the nanoelectrodes can monitor the fluctuation of intracellular DA under drug stimulation, providing new ideas and methods for new drug development and efficacy evaluation.

Alumina inorganic molecularly imprinted polymer modified multi-walled carbon nanotubes for uric acid detection in sweat

Alumina inorganic molecularly imprinted polymer (MIP) modified multi-walled carbon nanotubes (MWCNTs) on a glassy carbon electrode (MWCNTs-Al2O3-MIP/GCE) was firstly designed and fabricated by one-step electro deposition technique for the detection of uric acid (UA) in sweat. The UA templates were embedded within the inorganic MIP by co-deposition with Al2O3. Through the evaluation of morphology and structure by Field Emission Scanning Electron Microscope (SEM), Energy Dispersive X-ray Spectroscopy (EDS), X-ray Photoelectron Spectroscopy (XPS) and Transmission Electron Microscopy (TEM), it was verified that the specific recognition sites can be fabricated in the electrodeposited Al2O3 molecular imprinted layer. Due to the high selectivity of molecular imprinting holes, the MWCNTs-Al2O3-MIP/GCE electrode demonstrated an impressive imprinting factor of approximately 2.338 compared to the non-molecularly imprinted glassy carbon electrode (MWCNTs-Al2O3-NIP/GCE) toward uric acid detection. Moreover, it exhibited a remarkable limit of detection (LOD) of 50 nM for UA with wide detection range from 50 nM to 600 μM. The MWCNTs-Al2O3-MIP/GCE electrode also showed strong interference resistance against common substances found in sweat. These results highlight the excellent interference resistance and selectivity of MWCNTs-Al2O3-MIP/GCE sensor, positioning it as a novel sensing platform for non-invasive uric acid detection in human sweat.

MXene-Based Chemo-Sensors and Other Sensing Devices

MXenes have received worldwide attention across various scientific and technological fields since the first report of the synthesis of Ti3C2 nanostructures in 2011. The unique characteristics of MXenes, such as superior mechanical strength and flexibility, liquid-phase processability, tunable surface functionality, high electrical conductivity, and the ability to customize their properties, have led to the widespread development and exploration of their applications in energy storage, electronics, biomedicine, catalysis, and environmental technologies. The significant growth in publications related to MXenes over the past decade highlights the extensive research interest in this material. One area that has a great potential for improvement through the integration of MXenes is sensor design. Strain sensors, temperature sensors, pressure sensors, biosensors (both optical and electrochemical), gas sensors, and environmental pollution sensors targeted at volatile organic compounds (VOCs) could all gain numerous improvements from the inclusion of MXenes. This report delves into the current research landscape, exploring the advancements in MXene-based chemo-sensor technologies and examining potential future applications across diverse sensor types.

Research progress on preparation methods and sensing applications of molecularly imprinted polymer-aptamer dual recognition elements

The aptamer (Apt) and the molecularly imprinted polymer (MIP), as effective substitutes for antibodies, have received widespread attention from researchers because of their creation. However, the low stability of Apt in harsh detection environment and the poor specificity of MIP have hindered their development. Therefore, some researchers have attempted to combine MIP with Apt to explore whether the effect of "1 + 1 > 2" can be achieved. Since its first report in 2013, MIP-Apt dual recognition elements have become a highly focused research direction in the fields of biology and chemistry. MIP-Apt dual recognition elements not only possess the high specificity of Apt and the high stability of MIP in harsh detection environment, but also have high sensitivity and affinity. They have been successfully applied in medical diagnosis, food safety, and environmental monitoring fields. This article provides a systematic overview of three preparation methods for MIP-Apt dual recognition elements and their application in eight different types of sensors. It also provides effective insights into the problems and development directions faced by MIP-Apt dual recognition elements.

Advances in Electrochemical Biosensors for the Detection of Common Oral Diseases

Limiting and preventing oral diseases remains a major challenge to the health of populations around the world, so finding ways to detect early-stage diseases (e.g., caries, periodontal disease, and oral cancer) and aiding in their prevention has always been an important clinical treatment concept. The development and application of electrochemical detection technology can provide important support for the early detection and non-invasive diagnosis of oral diseases and make up for the shortcomings of traditional diagnostic methods, which are highly sensitive, non-invasive, cost-effective, and less labor-intensive. It detects specific disease markers in body fluids through electrochemical reactions, discovers early warning signals of diseases, and realizes rapid and reliable diagnosis. This paper comprehensively summarizes the development and application of electrochemical biosensors in the detection and diagnosis of common oral diseases in terms of application platforms, sensing types, and disease detection, and discusses the challenges faced by electrochemical biosensors in the detection of oral diseases as well as the great prospects for future applications, in the hope of providing important insights for the future development of electrochemical biosensors for the early detection of oral diseases.

Electrochemical bio- and chemosensors for cancer biomarkers: Natural (with antibodies) versus biomimicking artificial (with aptamers and molecularly imprinted polymers) recognition

Electrochemical (EC) bio- and chemosensors are highly promising for on-chip and point-of-care testing (POST) devices. They can make a breakthrough in early cancer diagnosis. Most current EC sensors for cancer biomarkers' detection and determination use natural antibodies as recognition units. However, those quickly lose their biorecognition ability upon exposure to harsh environments, comprising extreme pH, humidity, temperature, etc. So-called "plastic antibodies," including aptamers and molecularly imprinted polymers (MIPs), are hypothesized to be a smart alternative to antibodies. They have attracted the interest of the sensor research community, offering a low cost-to-performance ratio with high stability, an essential advantage toward their commercialization. Herein, we critically review recent technological advances in devising and fabricating EC bio- and chemosensors for cancer biomarkers, classifying them according to the type of recognition unit used into three categories, i.e., antibody-, aptamer-, and MIP-based EC sensors for cancer biomarkers. Each sensor fabrication strategy has been discussed, from the devising concept to cancer sensing applications, including using different innovative nanomaterials and signal transduction strategies. Moreover, employing each recognition unit in the EC sensing of cancer biomarkers has been critically compared in detail to enlighten each recognition unit's advantages, effectiveness, and limitations.

A novel carbonized polymer dots-based molecularly imprinted polymer with superior affinity and selectivity for oxytetracycline removal

Molecularly imprinted polymers (MIPs) synthesized from chain functional monomers are restricted by spatial extension and exhibit relatively poor affinity and selectivity; this results in unsatisfactory applications in complex media. In this study, we prepared unique spherical carbonized polymer dots (CPDs-OH) via the incomplete carbonization of 1-allyl-3-vinylimidazolium bromide and ethylene glycol, and used it as a functional monomer to prepare a newly imprinted polymer (CPDs-OH@MIP) in aqueous media. As a result, the CPDs-OH@MIP exhibited effective recognition of oxytetracycline with an impressive imprinting factor of 6.17, surpassing MIPs prepared with chain functional monomers (1-3). Furthermore, CPDs-OH@MIP exhibited excellent adsorption for oxytetracycline (278.52 mg g-1) and achieved equilibrium in 30 min, with stronger resistance to coexisting cations, anions, and humic acid. Compared to other MIPs and adsorbents, the recognition performance of CPDs-OH@MIP improved 2-4 times; this polymer could remove >92.1% of oxytetracycline in real water samples with at least 10 cycle times. CPDs-OH@MIP prepared using the special spherical monomer forms a denser structure with fewer nonimprinted regions and precisely imprinted sites, remarkably improving the affinity and selectivity of MIPs combined via hydrogen bonds and electrostatic and π-π interactions. Our proposed strategy provides an effective basis for breakthroughs in the practical application of MIPs.

Protein-imprinted polymers: How far have "plastic antibodies" come?

Antibodies are highly selective and sensitive, making them the gold standard for recognition affinity tools. However, their production cost is high and their downstream processing is time-consuming. Molecularly imprinted polymers (MIPs) are tailor-made by incorporating specific molecular recognition sites in their structure, thus translating into receptor-like activity mode of action. The interest in molecular imprinting technology, applied to biomacromolecules, has increased in the past decade. MIPs, produced using biomolecules as templates, commonly referred to as "plastic antibodies" or "artificial receptors", have been considered as suitable cheaper and easy to produce alternatives to antibodies. Research on MIPs, designed to recognize proteins or peptides is particularly important, with potential contributions towards biomedical applications, namely biosensors and targeted drug delivery systems. This mini review will cover recent advances on (bio)molecular imprinting technology, where proteins or peptides are targeted or mimicked for sensing and therapeutic applications. Polymerization methods are reviewed elsewhere, being out of the scope of this review. Template selection and immobilization approaches, monomers and applications will be discussed, highlighting possible drawbacks and gaps in research.

Preparation and Performance Analysis of 3D Thermoformed Fluidic Polymer Temperature Sensors for Aquatic and Terrestrial Applications

Employing a combination of Polyethylene terephthalate (PET) thermoforming and 3D-printed cylindrical patterns, we carefully engineer a linear resistive temperature sensor. This intricate process involves initial PET thermoforming, yielding a hollow cylindrical chamber. This chamber is then precisely infused with a composite fluid of graphite and water glue. Ensuring electrical connectivity, both ends are affixed with metal wires and securely sealed using a hot gun. This cost-effective, versatile sensor adeptly gauges temperature shifts by assessing composite fluid resistance alterations. Its PET outer surface grants immunity to water and solubility concerns, enabling application in aquatic and aerial settings without extra encapsulation. Rigorous testing reveals the sensor's linearity and stability within a 10 °C to 60 °C range, whether submerged or airborne. Beyond 65 °C, plastic deformation arises. To mitigate hysteresis, a 58 °C operational limit is recommended. Examining fluidic composite width and length effects, we ascertain a 12 Ω/°C sensitivity for these linear sensors, a hallmark of their precision. Impressive response and recovery times of 4 and 8 s, respectively, highlight their efficiency. These findings endorse thermoforming's potential for fabricating advanced temperature sensors. This cost-effective approach's adaptability underscores its viability for diverse applications.

In situ synthesis and dynamic simulation of molecularly imprinted polymeric nanoparticles on a micro-reactor system

Current practices in synthesizing molecularly imprinted polymers face challenges-lengthy process, low-productivity, the need for expensive and sophisticated equipment, and they cannot be controlled in situ synthesis. Herein, we present a micro-reactor for in situ and continuously synthesizing trillions of molecularly imprinted polymeric nanoparticles that contain molecular fingerprints of bovine serum albumin in a short period of time (5-30 min). Initially, we performed COMSOL simulation to analyze mixing efficiency with altering flow rates, and experimentally validated the platform for synthesizing nanoparticles with sizes ranging from 52-106 nm. Molecular interactions between monomers and protein were also examined by molecular docking and dynamics simulations. Afterwards, we benchmarked the micro-reactor parameters through dispersity and concentration of molecularly imprinted polymers using principal component analysis. Sensing assets of molecularly imprinted polymers were examined on a metamaterial sensor, resulting in 81% of precision with high selectivity (4.5 times), and three cycles of consecutive use. Overall, our micro-reactor stood out for its high productivity (48-288 times improvement in assay-time and 2 times improvement in reagent volume), enabling to produce 1.4-1.5 times more MIPs at one-single step, and continuous production compared to conventional strategy.

Bisphenol A detection based on nano gold-doped molecular imprinting electrochemical sensor with enhanced sensitivity

A facile electrochemical sensor based on nano gold-doped molecularly imprinted polymer (MIP) was proposed to realize the selective detection of bisphenol A (BPA) with enhanced sensitivity. Initially, gold-doped MIP (Au@MIP) film was constructed by electropolymerizing p-aminobenzoic acid (PABA) and BPA with in situ gold reduction to distribute gold nanoparticles nearby the imprinted cavities. Subsequently, the template molecules were further extracted from the polymer film, then the MIP could rebind with the template molecules to achieve specific detection of BPA. The nano gold-doped MIP increased the effective surface area and promoted conductivity when BPA was oxidized in the imprinted cavities, which improved the determination sensitivity. Under optimal conditions, the prepared sensor displayed a linear range from 0.5 to 100 μM for BPA detection with a detection limit of 52 nM. The designed sensor was further used to detect BPA in food samples, obtaining satisfactory recoveries from 96.7% to 107.6%.

A surface molecularly imprinted electrochemical biosensor for the detection of SARS-CoV-2 spike protein by using Cu7S4-Au as built-in probe

Sensitive detection of severe acute respiratory syndrome coronavirus-2 (SARS-CoV-2) spike protein (S protein) is of significant clinical importance in the diagnosis of COVID-19 pandemic. In this work, a surface molecularly imprinted (SMI) electrochemical biosensor is fabricated for the detection of SARS-CoV-2 S protein. Cu₇S₄-Au is used as the built-in probe and modified on the surface of a screen-printed carbon electrode (SPCE). 4-Mercaptophenylboric acid (4-MPBA) is anchored to the surface of the Cu₇S₄-Au through Au-SH bonds, which can be used for the immobilization of the SARS-CoV-2 S protein template through boronate ester bonds. After that, 3-aminophenylboronic acid (3-APBA) is electropolymerized on the electrode surface and used as the molecularly imprinted polymers (MIPs). The SMI electrochemical biosensor is obtained after the elution of the SARS-CoV-2 S protein template with an acidic solution by the dissociation of the boronate ester bonds, which can be utilized for sensitive detection of the SARS-CoV-2 S protein. The developed SMI electrochemical biosensor displays high specificity, reproducibility and stability, which might be a potential and promising candidate for the clinical diagnosis of COVID-19.

Magnetic dummy template molecularly imprinted particles functionalized with dendritic nanoclusters for selective enrichment and determination of 4-methylnitrosamino-1-(3-pyridyl)-1-butanone (NNK) in tobacco products

The compound 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone (NNK), one of the tobacco specific nitrosamines (TSNAs), is widely recognized as a major carcinogen found in tobacco products, environmental tobacco smoke and wastewater. Thus, a selective enrichment and sensitive detection method for monitoring the risk of NNK exposure is highly desirable. In this study, a magnetic molecularly imprinted polymer (MMIP) functionalized with dendritic nanoclusters was synthesized to selectively recognize NNK via the dummy template imprinting strategy, aiming to avoid residual template leakage and increase the imprinting efficiency. The nanocomposites were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, as well as vibrating sample magnetometry (VSM) and nitrogen adsorption/desorption analysis. The resulting MMIPs exhibited high adsorption capacity, fast binding kinetics and good selectivity for trace amounts of NNK. A rapid, low cost and efficient method for detecting NNK in tobacco products was established using magnetic dispersive solid-phase extraction coupled with HPLC-DAD with a good linear range of 0.1-250 μg mL^-1. The limit of detection (LOD) and limit of quantification (LOQ) of NNK were 13.5 and 25.0 ng mL^-1, respectively. The average recoveries were 87.8-97.3% with RSDs lower than 3%. The results confirmed that the MMIPs could be used as an excellent selective adsorbent for NNK, with potential applications in the pretreatment of tobacco products.

Improving the sensitivity and selectivity of sulfonamides electrochemical detection with double-system imprinted polymers

The extensive use of antibiotics leading to the rapid spread of antibiotic resistance poses high health risks to humans, but to date there is still lack of an on-site detection method of SA residues. In this study, we integrated radical polymerization using sodium p-styrenesulfonate as a functional monomer and the self-polymerization of dopamine to prepare double-system imprinted polymers (DIPs) using sulfonamide antibiotics as templates. We found that the DIPs were semi-interpenetrating polymer networks and introduction of poly(dopamine) improved the selectivity of the imprinted cavities as well as the conductivity. The selectivity and sensitivity of the sensor using DIPs were much higher than those using single-system MIPs. This sensor could determine sulfonamides in complex samples in the presence of structural analogues. The linear range was from 0.01 to 10.00 μmol L^-1 with a detection limit of 4.00 nmol L^-1. Furthermore, based on the highly selective DIPs and statistics analysis, this method could be used for simultaneous analysis of 4 sulfonamide types in real samples with an accuracy of 94.87 %. This work provides a strategy to improve the selectivity and sensitivity of MIPs based-sensor that can serve as tool for the simultaneous analysis of antibiotic residues in environment samples.

Electrochemical sensor based on molecularly imprinted polymer cryogel and multiwalled carbon nanotubes for direct insulin detection

Insulin is the polypeptide hormone that regulates blood glucose levels. It is used as an indicator of both types of diabetes. An electrochemical insulin sensor was developed using a gold electrode modified with carboxylated multiwalled carbon nanotubes (f-MWCNTs) and molecularly imprinted polymer (MIP) cryogel. The MIP provided specific recognition sites for insulin, while the macropores of the cryogel promoted the mass transfer of insulin to the recognition sites. The f-MWCNTs increased the effective surface area and conductivity of the sensor and also reduced the potential required to oxidize insulin. Insulin oxidation was directly measured in a flow system using square wave voltammetry. This MIP cryogel/f-MWCNTs sensor provided a linear range of 0.050-1.40 pM with a very low limit of detection (LOD) of 33 fM. The sensor exhibited high selectivity and long-term stability over 10 weeks of dry storage at room temperature. The results of insulin determination in human serum using the sensor compared well with the results of the Elecsys insulin assay. The developed MIP sensor offers a promising alternative for the diagnosis and treatment of diabetes.

Group-targeting sulfonamides via an evanescent-wave biosensor based on rational designed coating antigen

In order to effectively monitor a wide variety of sulfonamides residues in the environment, group-targeting immunoassay based on the group-specific antibodies has attracted great attentions, which can realize the detection of a group of contaminants in environment as many as possible even the unrecognized ones. Indirect competitive immunoassay is generally adopted for small molecule detection however the rational design of immobilized coating antigen for improved recognition capability on the solid surface is far from enough. To cover the research gap, we proposed the design criteria of coating antigen for surface-based indirect competitive immunoassay based on the molecular docking. Taking the group-specific antibodies against sulfonamides (SA) as a proof-of-concept, a hapten with a linking arm with 3 methyl groups was selected to synthesize the coating antigen. Through surface immobilization of coating antigen, a portable biosensor for group-targeting immunoassay of sulfonamides was developed and demonstrated excellent performance with detection limits lower than 0.6 μg/L for four SA variants, and the cross-reactivities of 148-215 % relative to sulfadiazine. The recovery rates of SAs in liquid milk ranges from 87 to 97 %, which confirmed the application potential of this method in the determination of SAs. Its capability to measure total SAs in a simple and low-cost way would pave the way for a variety of application fields.

Molecularly Imprinted Polymers for the Determination of Cancer Biomarkers

Biomarkers can provide critical information about cancer and many other diseases; therefore, developing analytical systems for recognising biomarkers is an essential direction in bioanalytical chemistry. Recently molecularly imprinted polymers (MIPs) have been applied in analytical systems to determine biomarkers. This article aims to an overview of MIPs used for the detection of cancer biomarkers, namely: prostate cancer (PSA), breast cancer (CA15-3, HER-2), epithelial ovarian cancer (CA-125), hepatocellular carcinoma (AFP), and small molecule cancer biomarkers (5-HIAA and neopterin). These cancer biomarkers may be found in tumours, blood, urine, faeces, or other body fluids or tissues. The determination of low concentrations of biomarkers in these complex matrices is technically challenging. The overviewed studies used MIP-based biosensors to assess natural or artificial samples such as blood, serum, plasma, or urine. Molecular imprinting technology and MIP-based sensor creation principles are outlined. Analytical signal determination methods and the nature and chemical structure of the imprinted polymers are discussed. Based on the reviewed biosensors, the results are compared, and the most suitable materials for each biomarker are discussed.

Application of Polypyrrole-Based Electrochemical Biosensor for the Early Diagnosis of Colorectal Cancer

Although colorectal cancer (CRC) is easy to treat surgically and can be combined with postoperative chemotherapy, its five-year survival rate is still not optimistic. Therefore, developing sensitive, efficient, and compliant detection technology is essential to diagnose CRC at an early stage, providing more opportunities for effective treatment and intervention. Currently, the widely used clinical CRC detection methods include endoscopy, stool examination, imaging modalities, and tumor biomarker detection; among them, blood biomarkers, a noninvasive strategy for CRC screening, have shown significant potential for early diagnosis, prediction, prognosis, and staging of cancer. As shown by recent studies, electrochemical biosensors have attracted extensive attention for the detection of blood biomarkers because of their advantages of being cost-effective and having sound sensitivity, good versatility, high selectivity, and a fast response. Among these, nano-conductive polymer materials, especially the conductive polymer polypyrrole (PPy), have been broadly applied to improve sensing performance due to their excellent electrical properties and the flexibility of their surface properties, as well as their easy preparation and functionalization and good biocompatibility. This review mainly discusses the characteristics of PPy-based biosensors, their synthetic methods, and their application for the detection of CRC biomarkers. Finally, the opportunities and challenges related to the use of PPy-based sensors for diagnosing CRC are also discussed.

Novel Dual-Signal SiO2-COOH@MIPs Electrochemical Sensor for Highly Sensitive Detection of Chloramphenicol in Milk

In view of the great threat of chloramphenicol (CAP) to human health and the fact that a few producers have illegally used CAP in the food production process to seek economic benefits in disregard of laws and regulations and consumer health, we urgently need a detection method with convenient operation, rapid response, and high sensitivity capabilities to detect CAP in food to ensure people's health. Herein, a molecularly imprinted polymer (MIP) electrochemical sensor based on a dual-signal strategy was designed for the highly sensitive analysis of CAP in milk. The NiFe Prussian blue analog (NiFe-PBA) and SnS₂ nanoflowers were modified successively on the electrode surface to obtain dual signals from [Fe(CN)₆]^3-/4- at 0.2 V and NiFe-PBA at 0.5 V. SiO₂-COOH@MIPs that could specifically recognize CAP were synthesized via thermal polymerization using carboxylated silica microspheres (SiO₂-COOH) as carriers. When the CAP was adsorbed by SiO₂-COOH@MIPs, the above two oxidation peak currents decreased at the same time, allowing the double-signal analysis. The SiO₂-COOH@MIPs/SnS₂/NiFe-PBA/GCE sensor used for determining CAP was successfully prepared. The sensor utilized the interactions of various nanomaterials to achieve high-sensitivity dual-signal detection, which had certain innovative significance. At the same time, the MIPs were synthesized using a surface molecular imprinting technology, which could omit the time of polymerization and elution and met the requirements for rapid detection. After optimizing the experimental conditions, the detection range of the sensor was 10^-8 g/L-10^-2 g/L and the limit of detection reached 3.3 × 10^-9 g/L (S/N = 3). The sensor had satisfactory specificity, reproducibility, and stability, and was successfully applied to the detection of real milk samples.

Detection of Residual 2-Phenylphenol on Lemon Rind by Electrochemically Deposited Poly(hydroxybenzaldehyde) and Poly(hydroxybenzoic acid) Polymeric Stackings as Electrode Modifiers

This study explores the characteristics of electrodeposition of the three hydroxybenzaldehyde isomers and selected hydroxybenzoic acids (4-hydroxybenzoic acid, salicylic acid, 3,5-dihydroxybenzoic acid) from mesityl oxide solvent. Similar to recent advances of this solvent, used by electrochemical studies, the carbon-carbon double bond had significant influence on the formation of polymers from the outlined molecules. In case of most substrates the peak currents increased to a steady-state but electropolymerization of some substrates caused significant deactivation. Scanning electron microscopic and complementary voltammetric studies facilitated that the electrochemically formed polymers are present on the electrode surface in stackings. In viewpoint of analysis of 2-phenylphenol, the modifying deposit formed from 4-hydroxybenzaldehyde was the best with 5 µM detection limit obtained with differential pulse voltammetry. Furthermore, a new procedure was chosen for the involvement of a cavitand derivative into the organic layers with the purpose to improve the layer selectivity (subsequent electrochemical polymerization in an other solution). Further studies showed that in this way the sensitivities of as-modified electrodes were a little worse than without this step, thus indicating that application of this step is disadvantageous. Recovery studies of 2-phenylphenol were carried out on lemon rind without any treatment, and it was compared with the case when the outer yellow layer was removed by rasping. The inner tissues showed very high adsorption affinity towards 2-phenylphenol.

Rapid Conductometric Detection of SARS-CoV-2 Proteins and Its Variants Using Molecularly Imprinted Polymer Nanoparticles

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) biosensors have captured more attention than the conventional methodologies for SARS-CoV-2 detection due to having cost-effective platforms and fast detection. However, these reported SARS-CoV-2 biosensors suffer from drawbacks including issues in detection sensitivity, degradation of biomaterials on the sensor's surface, and incapability to reuse the biosensors. To overcome these shortcomings, molecularly imprinted polymer nanoparticles (nanoMIPs) incorporated conductometric biosensor for highly accurate, rapid, and selective detection of two model SARS-CoV-2 proteins: (i) receptor binding domain (RBD) of the spike (S) glycoprotein and (ii) full length trimeric spike protein are introduced. In addition, these biosensors successfully responded to several other SARS-CoV-2 RBD spike protein variants including Alpha, Beta, Gamma, and Delta. Our conductometric biosensor selectively detects the two model proteins and SARS-CoV-2 RBD spike protein variant samples in real-time with sensitivity to a detection limit of 7 pg mL-1 within 10 min of sample incubation. A battery-free, wireless near-field communication (NFC) interface is incorporated with the biosensor for fast and contactless detection of SARS-CoV-2 variants. The smartphone enabled real-time detection and on-screen rapid result for SARS-CoV-2 variants can curve the outbreak due to its ability to alert the user to infection in real time.

Imprinted biopolymers as green abiotic route in immunoglobulin affinity plasmonic sensing

The relentless research in material science is pushing towards sustainable building blocks, which may be exploited in the molecularly imprinting technology, a potentially ground-breaking tool for producing affinity mimetic receptors. In this scenario, we report and characterize a novel polynorepinephrine (PNE)-based mimetic for IgG detection, biomolecules of utmost clinical interest, coupled to a label-free and real-time sensing based on Surface Plasmon Resonance (SPR). A "molecular walk" around the Y-shaped IgG structure is performed to select small peptide portions to be used as templates during the epitope imprinting process. For real-time diagnosis, the mimetic receptor is integrated into SPR sensing platform, to directly target the IgG both in standard solutions and human serum specimens using the standard addition method. The designed platform is characterized in terms of binding kinetic/affinity parameters and analytical figures of merit, (selectivity, repeatability, limit of detection and quantification, namely 0.90 ± 0.02 μg mL^-1 and 3.01 ± 0.07 μg mL^-1, respectively), displaying excellent promising outcomes also when the material is subjected to thermal stress. Comprehensively, the excellent analytical performances of the MIP-based SPR sensing and the well-known versatility of such biopolymer encourage the further development of serological point-of-care testing for IgG antibodies detection.

Biosensors Based on Bio-Functionalized Semiconducting Metal Oxides

Immobilization of biomaterials is a very important task in the development of biofuel cells and biosensors. Some semiconducting metal-oxide-based supporting materials can be used in these bioelectronics-based devices. In this article, we are reviewing some functionalization methods that are applied for the immobilization of biomaterials. The most significant attention is paid to the immobilization of biomolecules on the surface of semiconducting metal oxides. The improvement of biomaterials immobilization on metal oxides and analytical performance of biosensors by coatings based on conducting polymers, self-assembled monolayers and lipid membranes is discussed.

Reusable and universal impedimetric sensing platform for the rapid and sensitive detection of pathogenic bacteria based on bacteria-imprinted polythiophene film

A bacteria-imprinted polythiophene film (BIF)-based impedimetric sensor was proposed for the rapid and sensitive detection of S. aureus. A significant improvement is the reduced time for both BIF fabrication (15 min) and bacterial capturing (10 min).

Selective non-enzymatic uric acid sensing in the presence of dopamine: electropolymerized poly-pyrrole modified with a reduced graphene oxide/PEDOT:PSS composite

A molecularly imprinted polymer (MIP) with uric acid cavities increases the selectivity of uric acid measurement in the presence of dopamine as an interferent.