Heavy metals adsorption by banana peels micro-powder: Equilibrium modeling by non-linear models

Sequestration of chromium(vi) and nickel(ii) heavy metals from unhygienic water via sustainable and innovative magnetic nanotechnology

In a stride towards sustainable solutions, this research endeavors to address the critical issue of water pollution via heavy metals by coupling the power of magnetic nanotechnology, in combination with a green chemistry approach, to eliminate two noxious inorganic pollutants: chromium(vi) and nickel(ii) from aqueous environments. The synthesis of magnetite (Fe3O4) nanoparticles was achieved using ferric chloride hexahydrate (FeCl3·6H2O) as a precursor, with the assistance of Ziziphus mauritiana Lam. leaves extract, known for its remarkable salt-reducing properties. A range of bio-adsorbents, derived from corncob biomass, corncob pyrolyzed biochar, and magnetite/corncob biochar nanocomposite (NC), were engineered for their eco-friendly and biocompatible characteristics. Extensive parametric optimizations, including variations in pH, contact time, dose rate, and concentration, were carried out to gain insights into the adsorption behavior and capacity of these bioadsorbents concerning Cr(vi) and Ni(ii). Equilibrium and kinetic studies were undertaken to comprehensively understand the adsorption dynamics. In the case of Ni(ii), the Freundlich isotherm model provided a satisfactory fit for all bio-adsorbents, demonstrating R2 values of 0.91, 0.95, and 0.96 for BM, BC, and NC, respectively. Furthermore, the pseudo 1st order model emerged as the most suitable fit for Cr(vi) sequestration in corncob BM with an R2 value of 0.98, while pseudo 2nd order models were robustly fitted for BC and NC, yielding R2 values of 0.88 and 0.99, respectively. The magnetite/corncob nanocomposite outperformed other bioadsorbents in removing heavy metals from wastewater due to its environmental friendliness, larger surface area, reusability, and cost-effectiveness at an industrial scale.

Banana Peel Powder Biosorbent for Removal of Hazardous Organic Pollutants from Wastewater

Disposing of pollutants in water sources poses risks to human health and the environment, but biosorption has emerged as an eco-friendly, cost-effective, and green alternative for wastewater treatment. This work shows the ability of banana peel powder (BPP) biosorbents for efficient sorption of methylene blue (MB), atrazine, and glyphosate pollutants. The biosorbent highlights several surface chemical functional groups and morphologies containing agglomerated microsized particles and microporous structures. BPP showed a 66% elimination of MB in 60 min, with an adsorption capacity (qe) of ~33 mg g-1, and a combination of film diffusion and chemisorption governed the sorption process. The biosorbent removed 91% and 97% of atrazine and glyphosate pesticides after 120 min, with qe of 3.26 and 3.02 mg g-1, respectively. The glyphosate and atrazine uptake best followed the Elovich and the pseudo-first-order kinetic, respectively, revealing different sorption mechanisms. Our results suggest that BPP is a low-cost biomaterial for green and environmentally friendly wastewater treatment.

Pseudomonas alcaliphila NEWG-2 as biosorbent agent for methylene blue dye: optimization, equilibrium isotherms, and kinetic processes

In comparison to physicochemical and chemical methods, microbial dye biosorption is regarded as an eco-effective and economically viable alternative and is a widely applied method due to its high efficiency and compatibility with the environment. Therefore, the idea of this study is to clarify to what extent the viable cells and the dry biomass of Pseudomonas alcaliphila NEWG-2 can improve the biosorption of methylene blue (MB) from a synthetic wastewater sample. The array of Taguchi paradigm has been conducted to ascertain five variables affecting the biosorption of MB by broth forms of P. alcaliphila NEWG. The data of MB biosorption were familiar to the predicted ones, indicating the precision of the Taguchi model's prediction. The maximum biosorption of MB (87.14%) was achieved at pH 8, after 60 h, in a medium containing 15 mg/ml MB, 2.5% glucose, and 2% peptone, with sorting the highest signal-to-noise ratio (38.80). FTIR spectra detected various functional groups (primary alcohol, α, β-unsaturated ester, symmetric NH₂ bending, and strong C-O stretching) on the bacterial cell wall that participated in the biosorption of MB. Furthermore, the spectacular MB biosorption ability was validated by equilibrium isotherms and kinetic studies (the dry biomass form), which were derived from the Langmuir model (q_max = 68.827 mg/g). The equilibrium time was achieved in about 60 min, with 70.5% of MB removal. The biosorption kinetic profile might be adequately represented by pseudo-second order and Elovich models. The changes in the bacterial cells before and after the biosorption of MB were characterized using a scanning electron microscope. As realized from the aforementioned data, the bacterium is a talented, effective, eco-friendly, and low-cost bio-sorbent for the decolorization and remedy of an industrial effluent containing MB from an aqueous environment. The current outcomes in the biosorption of MB molecules promote the use of the bacterial strain as viable cells and/or dry biomass in ecosystem restoration, environmental cleanup, and bioremediation studies.

Cu2+, Cr3+, and Ni2+ in mono- and multi-component aqueous solution adsorbed in passion fruit peels in natura and physicochemically modified: a comparative approach

Among the low-cost adsorbent are agricultural residues, which can be used in natura or modified forms. This work evaluated the adsorption of Ni²⁺, Cu²⁺, and Cr³⁺ in mono- and multi-component aqueous solutions using passion fruit peels in natura (Nat-PF) and physicochemically modified (Mod-PF). The adsorption was investigated by kinetic and isotherm models. A comparative investigation was conducted to analyze the effect of the experimental conditions by statistical test, adsorption capacity ratio, selectivity of adsorbate, and distribution coefficient. In both adsorbents, the process occurs in monolayer by chemosorption. Equilibrium was reached after 30 min, with highest adsorption capacity for Cu²⁺ as 0.495 mg g^-1, for Cr³⁺ as 0.483 mg g^-1, and for Ni²⁺ as 0.464 mg g^-1. The adsorption in Mod-PF was less affected in multi-component solutions, reducing the adsorption capacity by 0.06-0.15 times when compared to monocomponent solutions, while in Nat-PF a reduction of more than half of adsorption capacity was obtained. The modifications imposed on the biomass led to a change in its adsorptive selective, being Cr³⁺  > Cu²⁺  > Ni²⁺ for Nat-PF and Cu²⁺  > Ni²⁺  > Cr³⁺ for Mod-PF.

Isotherm models for adsorption of heavy metals from water - A review

Adsorption is a widely used technology for removing and separating heavy metal from water, attributed to its eco-friendly, cost-effective, and high efficiency. Adsorption isotherm modeling has been used for many years to predict the adsorption equilibrium mechanism, adsorption capacity, and the inherent characteristics of the adsorption process, all of which are substantial in evaluating the performance of adsorbents. This review summarizes the development history, fundamental characteristics, and mathematical derivations of various isotherm models, along with their applicable conditions and application scenarios in heavy metal adsorption. The latest progress in applying isotherm models with a one-parameter, two-parameter, and three-parameter in heavy metal adsorption using carbon-based materials, which has gained much attention in recent years as low-cost adsorbents, is critically reviewed and discussed. Several experimental factors affecting the adsorption equilibrium, such as solution pH, temperature, ionic strength, adsorbent dose, and initial heavy metal concentration, are briefly discussed. The criteria for selecting the optimum isotherm for heavy metal adsorption are proposed by comparing various adsorption models and analyzing mathematical error functions. Finally, the relative performance of different isotherm models for heavy metal adsorption is compared, and the future research gaps are identified.

Elucidation the influence of design variables on coagulation-flocculation mechanisms in the lab-scale bio-coagulation on toxic industrial effluent treatment

Bio-coagulants are environmentally friendly substances that have shown potential in removing organic and inorganic contaminants from wastewater from the Imitation Paint Industry. Under the optimized conditions, the use of the three bio-coagulants (of plant origin), Strychnos potatorum, Cactus opuntia and Portunus sanguinolentus (crab) shell (of animal origin) were evaluated, and their removal mechanism was based on kinetic models and adsorption isotherms. The error analysis method was used to find the best isotherm fit. In addition, the kinetic model parameters showed the absence of chemisorption and confirmed the existence of pore diffusion. The interaction between coagulant and pollutant, the type, homogeneity and intensity of the coagulation process, the pollutant absorption capacity of the coagulant were evaluated with the aid of the adsorption isotherm models. From the Pseudo first-order kinetic model an equilibrium pollutant uptake (mg/g) was marked as 598, 554 and 597 for Strychnos potatorum, Cactus opuntia and Portunus sanguinolentus respectively. The better affinity between the pollutants and the bio coagulants were observed through the lower values of Langmuir isotherm constant k_L. The adsorption intensity from Freundlich model (n_F) were ranged between 1 and 10 for all the listed coagulants, which revealed the physisorption behavior and heterogeneous mechanism of removal. With these results, it would be possible to conduct scale-up studies to adopt the process for practical systems.

Preparation, characterization, and application of modified magnetic biochar for the removal of benzotriazole: process optimization, isotherm and kinetic studies, and adsorbent regeneration

The adsorption of benzotriazole (BTA) by chemically modified magnetic biochar (MMBC) as a cheap and abundant biosorbent was investigated and optimized using response surface methodology (RSM). Initially, the MMBC composite was synthesized and characterized by scanning electron microscopy (SEM) energy dispersive X-ray spectroscopy (EDX), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and Brunauer-Emmett-Teller (BET) techniques. The characterization results confirmed the existence of Fe₃O₄ in the composite structure, which had uniformly dispersed over biochar (BC) with porous texture. Moreover, the presence of Zn and Cl elements in EDX analysis indicated that the magnetic biochar (MBC) had been modified successfully. The effects of chemical modification methods on the adsorption capacity of magnetic biochar were investigated. Maximum BTA removal efficiency was demonstrated by MMBC, modifying using ZnCl₂ (>99%). Optimization was carried out based on reaction time, BTA concentration and the concentration of adsorbent. Optimum experimental conditions for the removal of BTA from aqueous solutions were found to be 35 min of reaction time, 0.55 g/L of adsorbent, and 50 mg/L of initial BTA concentration. At these optimal conditions, the predicted BTA adsorption efficiency was 92.6%. The adsorption process followed the Avrami fractional-order reaction kinetic and the Langmuir adsorption isotherm with the maximum adsorption capacity of 563.1 mg/g. The values of thermodynamic parameters demonstrated that the adsorption of BTA on ZnCl₂-MBC is endothermic and spontaneous. Under optimum usage of MMBC, the adsorptive removal efficiency of BTA non-significantly decreased from 99.2 to 93.9% after the 5th cycle. Thus, MMBC can be recommended as an environmentally friendly and cost-effective adsorbent to remove micropollutants from water.

Magnetic adsorbent developed with alkali-thermal pretreated biogas slurry solids for the removal of heavy metals: optimization, kinetic, and equilibrium study

Discharge of effluents containing heavy metal without adequate treatment causes contamination of water resources and creates environmental and health issues. Adsorption could be applied to remediate heavy metals from wastewater effectively. In this study, a low-cost adsorbent was prepared by magnetic modification of pretreated biogas slurry solids (BSS) to remove heavy metals such as Cu²⁺, Cd²⁺, and Pb²⁺. The temperature (423 K) and time (1.5 h) of pretreatment, the BSS to KOH ratio (1:10 w/v), and the ratio of magnetic iron nanoparticle (MIN) to pretreated BSS (PSS) (1:2 w/w) were optimized for the preparation of adsorbent. The magnetically modified pretreated biogas slurry solid (MMPSS) adsorbent was characterized by BET isotherm, FTIR, XRD, FESEM, VSM, and EDX analysis. MMPSS attained equilibrium at 60 min and showed an adsorption capacity of 26.84 mg/g, 24.79 mg/g, and 23.86 mg/g with removal percentages 89.46%, 82.63%, and 79.54% for Cu²⁺, Cd²⁺, and Pb²⁺, respectively, at 310 K and pH 6 with an initial concentration of 150 mg/L. The adsorption process followed a pseudo second-order model with an R² value above 0.9 for all metals with a well-approaching equilibrium pattern. The good fit of experimental data by the Langmuir isotherm model implied monolayer adsorption. The metal ions adsorbed onto MMPSS were able to desorb effectively in the presence of HCl and retained 83.01%, 84.66%, and 81.83% of the initial adsorption capacity for Cu²⁺, Cd²⁺, and Pb²⁺ respectively after 5 consecutive cycles.

High-efficiency adsorption of Cd(II) and Co(II) by ethylenediaminetetraacetic dianhydride-modified orange peel as a novel synthesized adsorbent

The treatment of heavy metal (HM) wastewater is a critical and considerable challenge. Fruit peel-based HM adsorption is a promising way for the water pollution control and the reuse of agricultural waste. In this study, a novel adsorbent based on orange peel was synthesized for the first time by introducing abundant -COO groups with ethylenediaminetetraacetic dianhydride (EDTAD) to eliminate Cd(II) and Co(II) of sewage solution. The synthesized adsorbent displayed excellent adsorption capacity of 51.020 and 40.486 mg/g for Cd(II) and Co(II), respectively, and the adsorption equilibrium was achieved within 5 min, following the Langmuir isotherm model and the pseudo-second-order model. Surface characterization of adsorbents by scanning electron microscopy-energy dispersive X-ray spectroscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy confirmed that ion exchange, complexation, and physical adsorption could occur during the adsorption process. The rapid and highly efficient adsorption performance suggests EDTAD-modified synthesized orange peel possesses great potential for HM removal from sewage systems.

Removal of Reactive Black 5 Dye by Banana Peel Biochar and Evaluation of Its Phytotoxicity on Tomato

Removal of Reactive Black 5 (RB5) dye from an aqueous solution was studied by its adsorption on banana peel biochars (BPBs). The factors affecting RB5 dye adsorption such as pH, exposure time, RB5 dye concentration, adsorbent dose, particle size and temperature were investigated. Maximum 97% RB5 dye removal was obtained at pH 3 with 75 mg/L adsorbate concentration by banana peel biochars. Fourier transform infrared (FTIR) and scanning electron microscopy (SEM) were used to characterize the adsorbent material. The data of equilibrium were analyzed by Langmuir and Freundlich isotherm models. The experimental results were best reflected by Langmuir isotherm with maximum 7.58 mg/g adsorption capacity. Kinetic parameters were explored and pseudo-second order was found suitable which reflected that rate of adsorption was controlled by physisorption. Thermodynamic variables exhibited that the sorption process was feasible, spontaneous, and exothermic in nature. Banana peel biochar showed excellent regeneration efficiency up to five cycles of successive adsorption-desorption. Banana peel biochar maintained >38% sorption potential of RB5 dye even after five cycles of adsorption-desorption. The phytotoxic study exhibited the benign nature of BPB-treated RB5 dye on tomato seeds.

Fruit Peels as a Sustainable Waste for the Biosorption of Heavy Metals in Wastewater: A Review

One of the environmental challenges that is currently negatively affecting the ecosystem is the continuous discharge of untreated industrial waste into both water sources and soils. For this reason, one of the objectives of this qualitative study of exploratory-descriptive scope was the review of scientific articles in different databases-Scopus, Web of Science, and Science Direct-published from 2010 to 2021 on the use of fruit peels as a sustainable waste in the removal of heavy metals present in industrial wastewater. For the selection of articles, the authors used the PRISMA guide as a basis, with which 210 publications were found and 93 were compiled. Considering the reported work, a content analysis was carried out using NVivo 12 Plus and VOSviewer 1.6.17 software. The results show that the fruits mentioned in these publications are lemon, banana, mango, tree tomato, pineapple, passion fruit, orange, coconut, avocado, apple, lulo, and tangerine. However, no studies were found with lulo and tree tomato peels. On the other hand, the heavy metals removed with the selected fruit peels were Pb+2, Cr+3, Cr+6, Ni+2, Cd+2, As+5, Cu+2, and Zn+2.

Isotherm, kinetics, and adsorption mechanism studies of diethylenetriaminepentaacetic acid-modified banana/pomegranate peels as efficient adsorbents for removing Cd(II) and Ni(II) from aqueous solution

Two novel absorbents were synthesized for the first time by banana and pomegranate peels using diethylenetriaminepentaacetic acid (DTPA) modification to eliminate Cd(II) and Ni(II) of sewage. The DTPA-modified peels performed significantly higher adsorption capacity than unmodified materials. The maximum adsorption capacities of DTPA-modified banana/pomegranate peel were 46.729/46.296 mg/g for Cd(II), and 29.240/16.611 mg/g for Ni(II). Adsorption isotherm and kinetics models were simulated to determine their removal efficiency and potential for recovery of these two heavy metals. As the results, the adsorption reached equilibrium within 5 min and was well described by the pseudo-second order model and Langmuir isotherm. The surface morphology analysis of the synthetic materials by Scanning Electron Microscopy-Energy Dispersive X-ray spectroscopy, Fourier Transform Infrared spectroscopy, and X-ray Photoelectron Spectroscopy, implied that ion exchange, complexation, and physical adsorption may together contribute to Cd(II) and Ni(II) loading on DTPA-modified peels. This study demonstrates the feasibility of waste peels as cost-efficient bio-absorbents to remove Cd(II) and Ni(II) in sewage systems, and discovers potential adsorption mechanism of efficiency improvements after DTPA modification.

A review on adsorptive separation of toxic metals from aquatic system using biochar produced from agro-waste

Water is a basic and significant asset for living beings. Water assets are progressively diminishing due to huge populace development, industrial activities, urbanization and rural exercises. Few heavy metals include zinc, copper, lead, nickel, cadmium and so forth can easily transfer into the water system either direct or indirect activities of electroplating, mining, tannery, painting, fertilizer industries and so forth. The different treatment techniques have been utilized to eliminate the heavy metals from aquatic system, which includes coagulation/flocculation, precipitation, membrane filtration, oxidation, flotation, ion exchange, photo catalysis and adsorption. The adsorption technique is a better option than other techniques because it can eliminate heavy metals even at lower metal ions concentration, simplicity and better regeneration behavior. Agricultural wastes are low-cost biosorbent and typically containing cellulose have the ability to absorb a variety of contaminants. It is important to note that almost all agro wastes are no longer used in their original form but are instead processed in a variety of techniques to improve the adsorption capacity of the substance. The wide range of adsorption capacities for agro waste materials were observed and almost more than 99% removal of toxic pollutants from aquatic systems were achieved using modified agro-waste materials. The present review aims at the water pollution due to heavy metals, as well as various heavy metal removal treatment procedures. The primary objectives of this research is to include an overview of adsorption and various agriculture based adsorbents and its comparison in heavy metal removal.

A Review on the Removal of Carbamazepine from Aqueous Solution by Using Activated Carbon and Biochar

Carbamazepine (CBZ), one of the most used pharmaceuticals worldwide and a Contaminant of Emerging Concern, represents a potential risk for the environment and human health. Wastewater treatment plants (WWTPs) are a significant source of CBZ to the environment, polluting the whole water cycle. In this review, the CBZ presence and fate in the urban water cycle are addressed, with a focus on adsorption as a possible solution for its removal. Specifically, the scientific literature on CBZ removal by activated carbon and its possible substitute Biochar, is comprehensively scanned and summed up, in view of increasing the circularity in water treatments. CBZ adsorption onto activated carbon and biochar is analyzed considering several aspects, such as physicochemical characteristics of the adsorbents, operational conditions of the adsorption processes and adsorption kinetics and isotherms models. WWTPs usually show almost no removal of CBZ (even negative), whereas removal is witnessed in drinking water treatment plants through advanced treatments (even >90%). Among these, adsorption is considered one of the preferable methods, being economical and easier to operate. Adsorption capacity of CBZ is influenced by the characteristics of the adsorbent precursors, pyrolysis temperature and modification or activation processes. Among operational conditions, pH shows low influence on the process, as CBZ has no charge in most pH ranges. Differently, increasing temperature and rotational speed favor the adsorption of CBZ. The presence of other micro-contaminants and organic matter decreases the CBZ adsorption due to competition effects. These results, however, concern mainly laboratory-scale studies, hence, full-scale investigations are recommended to take into account the complexity of the real conditions.

Experimental and Numerical Study of Biochar Fixed Bed Column for the Adsorption of Arsenic from Aqueous Solutions

Two laboratory tests were carried out to verify the suitability of an Italian commercial biochar as an adsorbing material. The chosen contaminant, considered dissolved in groundwater, was As. The circular economic concept demands the use of such waste material. Its use has been studied in recent years on several contaminants. The possibility of using an efficient material at low cost could help the use of low-impact technologies like permeable reactive barriers (PRBs). A numerical model was used to derive the kinetic constant for two of the most used isotherms. The results are aligned with others derived from the literature, but they also indicate that the use of a large amount of biochar does not improve the efficiency of the removal. The particular origin of the biochar, together with its grain size, causes a decrease in contact time required for the adsorption. Furthermore, it is possible that a strong local decrease in the hydraulic conductibility does not allow for a correct dispersion of the flow, thereby limiting its efficiency.

Interaction between hexavalent chromium and biologically formed iron mineral-biochar composites: Kinetics, products and mechanisms

Biogenic Fe(II) is a dominant natural reductant to convert carcinogenic Cr(VI) to less toxic Cr(III). Field-applied biochar could promote microbial production of Fe(II) and form iron-biochar composites. Although there have been mounting research on the interactions of biochar or Fe(II) with Cr(VI), their coupling effects on Cr(VI) immobilization have been largely neglected. Here, iron mineral-biochar composite (IMBC) was prepared via biochar-mediated dissimilatory reduction of ferrihydrite or goethite by Shewanella oneidensis MR-1, and its reaction with Cr(VI) was investigated. IMBC was able to effectively remove aqueous Cr(VI) via reductive transformation by adsorbed Fe(II). The removal process nicely followed pseudo-second-order kinetics and Langmuir isotherm model. The removal ability of IMBC decreased with increasing pH (5.5-8.0) but was independent of ionic strength changes (0-100 mM). After reaction, the Fe-Cr coprecipitates formed on IMBC exhibited slightly higher Fe/Cr ratios (0.93-0.96) than those on corresponding iron mineral controls (0.88-0.94). For IMBC, while the presence of biochar decreased the reactivity of adsorbed Fe(II), their removal capacities were ~30% higher than those of iron minerals alone, due to the enhanced yields of adsorbed Fe(II). These findings improved our knowledge of interactions among biochar, iron mineral and iron-reducing bacteria and their contribution to chromium immobilization.

Effective Removal of Cyanide and Heavy Metals from an Industrial Electroplating Stream Using Calcium Alginate Hydrogels

A real electroplating wastewater, containing 51,190 mg/L of free cyanide (CNf), 4899 mg/L of Ni and 1904 mg/L of Cu, was treated with calcium alginate hydrogel beads (CAB), pure or impregnated with biodegraded grape marc (EBGM) or activated carbon (EAC) in order to reduce the elevated load of toxic pollutants below the regulatory limits. It was evaluated the effect of increasing the amount of bioadsorbent as well as the influence of two successive adsorption cycles in the removal efficiency of pollutants. The most favourable sorption conditions onto CAB provided removal percentages of 85.02% for CNf and between 93.40-98.21% for heavy metals regarding the raw wastewater. The adsorption capacity of each pollutant onto CAB was considerably increased during the first 30 min of contact time, but after achieving the equilibrium, the following sorption capacities were obtained: 1177, 107.3, 39.5 and 1.52 mg/g for CNf, Ni, Cu and Zn, respectively. The kinetic adsorption of pollutants onto the CAB was adjusted to different kinetic models, observing that kinetic data agreed with the pseudo-second-order model. The information about intraparticle diffusion mechanisms in the bioadsorption process was also interpreted.

Phosphorus-rich biochar produced through bean-worm skin waste pyrolysis enhances the adsorption of aqueous lead

In China, more than 10,000 tons of bean-worm, which is rich in protein (68.5%) and essential amino acids (52.8%), is consumed annually. Thus, a large amount of bean-worm skin waste is generated, and is often indiscriminately disposed of, potentially causing environment problems. In this study, bean-worm skin (BWS) waste was pyrolyzed at 500 °C to produce biochar (BWS-BC), and the surface properties of BWS and BWS-BC were characterized using various spectroscopic techniques. Pb(II) adsorption properties of BWS and the corresponding biochar as a function of solution pH, contact time, and equilibrium concentration of Pb(II) were examined using adsorption isotherm, kinetics and thermodynamics studies. The maximum Pb(II) adsorption capacities based on the Langmuir isotherm model were calculated as 45 and 62 mg g^-1 for BWS and BWS-BC, respectively, which were comparable to the values obtained for biochars derived from other agro-wastes. The adsorption feasibility, favorability and spontaneity of Pb(II), as derived from the thermodynamic parameters, indicated that chemisorption and precipitation (e.g., hydroxypyromorphite) were the main adsorption mechanism in case of BWS and BWS-BC, respectively. Thus, conversion of BWS to biochar for Pb(II) adsorption can be considered as a feasible, promising and high value-added approach for BWS recycling.

Synthesis and characterization of eco-friendly cellulose beads for copper (II) removal from aqueous solutions

In this study, novel cellulose-bead-based biosorbents (CBBAS) were successfully synthesized from almond shell using a simple three-step process: (i) dissolution of bleached almond shell in ionic liquid (1-butyl-3-methylimidazolium chloride), (ii) coagulation of cellulose-ionic liquid solution in water and (iii) freeze-drying. Their morphological, structural and physicochemical properties were thoroughly characterized. These biomaterials exhibited a 3D-macroporous structure with interconnected pores, which provided a high number of adsorption sites. It should be noted that CBBAS biosorbents were efficiently employed for the removal of copper (II) ions from aqueous solutions, showing high adsorption capacity: 128.24 mg g^-1. The biosorption equilibrium data obtained were successfully fitted to the Sips model and the kinetics were suitably described by the pseudo-second-order model. Besides, CBBAS biosorbents can be easily separated from the solution for their subsequent reuse, and thus, they represent a method for the removal of copper (II) from aqueous solutions that is not only eco-friendly but also economical.

Corncob-derived activated carbon for roxarsone removal from aqueous solution: isotherms, kinetics, and mechanism

In this study, the adsorption of roxarsone (ROX) onto corncob-derived activated carbon (AC) was optimized using response surface methodology (RSM). Following this, the AC was comprehensively characterized by FT-IR, SEM, and EDS analysis. The results showed that the highest ROX adsorption efficiency of 304.34 mg/g was obtained at the contact time of 262 min, initial pH of 2.5, adsorbent dosage of 0.4 g/L, and initial concentration of 240 mg/L. Besides, it was found that the adsorption equilibrium data was fitted well to the Langmuir and Sips isotherm models. The thermodynamic parameters (e.g., ΔG, ΔH, and ΔS) revealed the spontaneous and exothermic nature of ROX adsorption. As indicated by pseudo second-order kinetics model, the adsorption of ROX onto AC could be achieved through the hydrogen bond, π-π adsorbate-adsorbent interaction, and electrostatic interaction between AC surface functional group and molecular species variations of ROX at different pH values. Overall, it can be concluded that corncob-derived AC is an alternative option for removing ROX from aqueous solution.

Removal Efficiencies of Manganese and Iron Using Pristine and Phosphoric Acid Pre-Treated Biochars Made from Banana Peels

The purpose of this study was to compare the removal efficiencies of manganese (Mn) and iron (Fe) using pristine banana peel biochar (BPB) and phosphoric acid pre-treated biochars (PBPB) derived from banana peels. The removal efficiencies of Mn and Fe were investigated under different adsorbent dosages (0.4–2 g L−1), temperatures (15–45 °C), and ionic strengths (0–0.1 M), and were directly correlated to the differences in physicochemical properties of BPB and PBPB, to identify the removal mechanisms of heavy metals by adsorption processes. The removal of Mn by PBPB obeyed the Freundlich isotherm model while the removal of Mn and Fe by BPB followed the Langmuir isotherm model. However, the removal of Fe by PBPB followed both Freundlich and Langmuir isotherm models. The removal efficiencies of Mn and Fe by BPB and PBPB increased with increasing temperatures and decreased with increasing ionic strengths. PBPB more effectively removed Mn and Fe compared to BPB due to its higher content of oxygen-containing functional groups (O/C ratio of PBPB = 0.45; O/C ratio of BPB = 0.01), higher surface area (PBPB = 27.41 m2 g−1; BPB = 11.32 m2 g−1), and slightly greater pore volume (PBPB = 0.03 cm3 g−1; BPB = 0.027 cm3 g−1). These observations clearly show that phosphoric acid pre-treatment can improve the physicochemical properties of biochar prepared from banana peels, which is closely related to the removal of heavy metals by adsorption processes.

The Removal of Crystal Violet from Textile Wastewater Using Palm Kernel Shell-Derived Biochar

In this study, we explored the adsorption potential of biochar derived from palm kernel shell (BC-PKS) as an affordable adsorbent for the removal of crystal violet from wastewater. Kinetics, equilibrium, and thermodynamics studies were carried out to evaluate the adsorption of crystal violet onto BC-PKS. The kinetics adsorption process followed the pseudo-second-order model, indicating that the rate of adsorption is principally controlled by chemisorption. The adsorption equilibrium data were better fitted by the Langmuir isotherm model with a determination coefficient of 0.954 and a maximum adsorption of 24.45 mg/g. Thermodynamics studies found the adsorption of crystal violet by BC-PKS to be endothermic with increasing randomness at the BC-PKS/crystal violet interface. The percentage removal and adsorption capacity increased with the pH of the solution, as the negative charges on the biochar surface at high pH enhance the electrostatic attraction between crystal violet molecules and BC-PKS. Increasing the BC-PKS dosage from 0.1 to 1.0 g increased percent removal and decreased the adsorption capacity of crystal violet onto BC-PKS. Therefore, biochar from agricultural by-products, i.e., palm kernel shell, can be cost-effective adsorbents for the removal of crystal violet from textile wastewater.

Clanis bilineata larvae skin-derived biochars for immobilization of lead: Sorption isotherm and molecular mechanism

Clanis bilineata larva skin (CBLS), a new residue from the food industry, was first used to produce biochars by pyrolysis at 300 °C (CBLS300) and 700 °C (CBLS700), respectively, for Pb immobilization. The sorption isotherms and immobilization mechanisms of Pb on two biochars were investigated. CBLS700 exhibited more high-efficiency in sorption of Pb than CBLS300 due to the predicted maximum sorption capacity of CBLS700 (77.52 mg/g) was larger than that of CBLS300 (49.02 mg/g). Synchrotron-based microfocused X-ray fluorescence analysis exhibited the co-distribution of Pb and P in the sorption product of CBLS700 rather than CBLS300. Microfocused X-ray absorption near-edge structure analysis highlighted the significance of organic ligand in the biochar for Pb immobilization due to both sorption products have organic complexed Pb. Moreover, 25% of total Pb was present as hydrocerussite on CBLS300 but partially transformed into stable hydroxylpyromorphite on CBLS700 (~21%), which was in accordance with the analysis of scanning electron microscopy coupled with energy disperse spectra. Additionally, addition of CBLS700 was more effective in reducing the leachable Pb in shooting range soil than that of CBLS300. These results strongly suggested the potential application of the new biochar (CBLS700) for the remediation of Pb-contaminated soils.

Prediction models for monitoring heavy-metal accumulation by wheat (Triticum aestivum L.) plants grown in sewage sludge amended soil

Prediction of heavy-metal concentration in the edible parts of economic crops, based on their concentration in soil and other environmental factors, is urgently required for human risk assessment. The present investigation aimed to develop regression models for predicting heavy-metal concentration in wheat plants via their contents in sewage sludge amended soil, organic matter (OM) content and soil pH. The concentration of heavy metals in the plant tissues reflected its concentration in the soil with high Fe followed by Al, Mn, Cr, Zn, Ni, Co, Cu, and Pb. Soil OM content had a significant positive correlation with all investigated heavy-metal concentrations in the different tissues of wheat plants, while soil pH was negatively significant with most heavy metals except spike Pb and grain Cr. The bio-concentration factor of Al, Cu, and Zn from soil to wheat root was >1, while that of shoot, spikes, and grains was <1 for all heavy metals. Significantly valid regression models were developed with fluctuated coefficient of determination (R²), high model efficiency (ME) values and low mean normalized average error (MNAE). The significant positive correlations between the concentration of some heavy metals in the soil and the same in wheat tissues indicate the potential of this plant as a biomonitor for these metals in contaminated soils. The significant correlations between heavy-metal concentrations in soil and its properties (pH and OM) with metal concentrations in wheat plants support the prediction model as an appropriate option. This study recommends the use of models with R² greater than 50% and recommend other researchers to use our models according to their own specific conditions.

Removal of Cr3+ from tanning effluents by adsorption onto phosphate mine waste: Key parameters and mechanisms

The present study aims to investigate key parameters and mechanisms affecting Cr³⁺ removal from tanning wastewater using phosphate mine waste (PW) as adsorbent in batch mode. The initial Cr³⁺ concentration was 3920 mg.L^-1. The maximum removal capacity of Cr³⁺ was found to be 97.23 mg.g^-1 using 40 g.L^-1 of PW at 50 °C and at 200 rpm of stirring speed. Thermodynamic studies indicated that Cr³⁺ sorption is endothermic reaction of a physico-chemical adsorption process. Kinetic data were satisfactorily described by a pseudo-second order model. Cr³⁺ removal is probably involving several mechanisms: PW surface dissolution, precipitation, co-precipitation, ion exchange and adsorption. The chromium sorption seems modifying the crystalline structure of the adsorbent. Adsorption isotherm was described by Freundlich, Langmuir and Redlich-Peterson models. But statistically, Freundlich fit better the experimental data. Five error functions were used to check this result. Treatment of chromium effluent using PW as adsorbent can also eliminate more than 60% of organic matter and then can be considered as an effective biomaterial for tanning wastewater treatment.

Production, application and health effects of banana pulp and peel flour in the food industry

The past 20 years has seen rapid development of value-added food products. Using largely wasted fruit by-products has created a potential for sustainable use of these edible materials. The high levels of antioxidant activity, phenolic compounds, dietary fibres and resistant starch in banana pulp and peel have made this tropical fruit an outstanding source of nutritive ingredient for enrichment of foodstuffs. Accordingly, processing of separate banana parts into flour has been of interest by many researchers using different methods (oven drying, spouted bed drier, ultrasound, pulsed vacuum oven, microwave, spray drying and lyophilization). Regarding the high level of bioactive compounds, especially resistant starch in banana flour, the application of its flour in starchy foods provides a great opportunity for product development, even in gluten free foods. This review aims to provide concise evaluation of the health benefits of banana bioactive components and covers a wide range of literature conducted on the application of different parts of banana and the flour produced at various ripeness stages in the food industry. Of particular interest, the impact of drying methods on banana flour properties are discussed.

Dynamics and Kinetics of Cupric Ion Removal from Wastewaters by Tunisian Solid Crude Olive-Oil Waste

The present paper aims to develop a low cost, efficient, and environmentally-friendly process to purify (industrial) waters contaminated by copper by the use of oil mill wastes, through kinetic, thermodynamic, and equilibrium investigations. To do so, the raw adsorbent was characterized using different analytical techniques including X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy. Then, the interaction between copper and olive residues were examined during batch adsorption tests at various operating parameters, such as pH, initial concentration, contact time, and particle size. Kinetic data were best fitted with Broeurs-Sotolongo kinetic model. Additionally, it was found that film and intraparticle diffusion steps controlled simultaneously the mass transfer of copper onto olive mill solid waste. Among the eight tested models, Broeurs-Sotolongo isotherm suited the most the sorption, with regards to the function errors analysis. It was deduced that the adsorption of copper does not involve chemical bonds with high energy which allows easier regeneration steps and higher number of biosorbent regeneration cycles without any need for applying high temperature in the desorption reaction systems. The adsorption capacity (18.93 mg/g) calculated on the basis of this model was close to the experimental value (18.4 mg/g) but more interestingly it brought up that 50% of the generated amounts of olive wastes in Tunisia could eliminate 1.84 kTons of copper from industrial waters.

Highly dispersed core-shell iron nanoparticles decorating onto graphene nanosheets for superior Zn(II) wastewater treatment

This study reports the preparation of highly dispersed nanoscale zerovalent iron (nZVI) with core-shell structure decorated onto graphene nanosheets (Gr-NS) to form nZVI-Gr-NS composite. Meanwhile, its excellent performance for concentrated Zn(II) wastewater treatment is also studied. The adsorption of Zn(II) onto nZVI-Gr-NS is well simulated by the pseudo-second-order model, which indicates the adsorption is the rate-controlling step. Moreover, the adsorption isotherms of Zn(II) on the nZVI-Gr-NS can fit well with the Langmuir model. The negative thermodynamic parameters (△G^Ɵ, △H^Ɵ, △S^Ɵ) calculated from the temperature-dependent isotherms indicate that the sorption reaction of Zn(II) is an exothermic and spontaneous process. The high saturation magnetization (37.4 emu g^-1) of the nZVI-Gr-NS makes separation of nZVI-Gr-NS-bound Zn(II) easily and quickly from aqueous solution. Most importantly, nZVI-Gr-NS composites not only remove Zn(II) but also spontaneously remove As, Se, and Cu ions from real smelting wastewater samples. This study provides a good solution for heavy metal removal in real wastewater.

Review of Heavy Metal Adsorption Processes by Several Organic Matters from Wastewaters

Heavy metal contamination of natural rivers and wastewaters is a problem for both the environment and human society. The accumulation and adsorption of heavy metals could happen with several organic and inorganic matters, but the most used adsorbents are (biological and chemical) organic compounds. This review article presents the basics of heavy metal adsorption on several organic surfaces. There are many organic matters, which seem to be useful as agents for heavy metal adsorption. All of the cited authors and articles present the adsorption kinetics by the most used isotherm models (such as Langmuir and Freundlich isotherms). By comparing several research results presented by a pre-selected assortment of papers, we would like to give an overview of the microbiological, organic chemical, and other surface adsorption possibilities. We draw conclusions for two new adsorption fields (adsorption with biosorbent and artificial materials). We present an optional possibility to study adsorption kinetics, efficiency and regeneration methods to successfully conclude the heavy metal treatment process, and we make some recommendations about the efficient water usage calculations using the water allowance coefficient (WAC) indicator.

Removal of dye molecules from aqueous solution by carbon nanotubes and carbon nanotube functional groups: critical review

Scheme for the adsorption of dye molecules by CNTs and CNT functionality.