A high-performance biochar produced from bamboo pyrolysis with in-situ nitrogen doping and activation for adsorption of phenol and methylene blue

Effective amendment of cadmium in water and soil before and after aging of nitrogen-doped biochar: Preparation optimization, removal efficiency and mechanism

Nitrogen-doped biochar (NBC) is a green material for remediating heavy metal pollution, but it undergoes aging under natural conditions, affecting its interaction with heavy metals. The preparation conditions of NBC were optimized using response surface methodology (RSM), and NBC was subjected to five different aging treatments to analyze the removal efficiency of Cd(II) and soil remediation capability before and after aging. The results indicated that NBC achieved optimal performance with a mass ratio of 5:2.43, an immersion time of 10.66 h, and a pyrolysis temperature of 900 °C. Aging diminished NBC's adsorption capacity for Cd(II) but did not change the main removal mechanism of monolayer chemical adsorption. Freeze-thaw cycles (FT), UV aging (L), and composite aging (U) treatments increased the proportion of bioavailable-Cd, and all aging treatments facilitated the conversion of potentially bioavailable-Cd to non-bioavailable-Cd. The application of NBC and five aged NBCs reduced the proportion of bioavailable-Cd in the soil through precipitation and complexation, increasing the proportion of non-bioavailable-Cd. Aging modifies the physicochemical properties of NBC, thus influencing soil characteristics and ultimately diminishing NBC's ability to passivate Cd in the soil. This study provides reference for the long-term application of biochar in heavy metal-contaminated environments.

Heteroatom doped biochar-aluminosilicate composite as a green alternative for the removal of hazardous dyes: Functional characterization and modeling studies

In this work, a novel nitrogen-doped biochar bentonite composite was synthesized by a single-pot co-pyrolysis method. Batch studies were conducted to evaluate the performance of the developed composite in eliminating synthetic dyes from the aqueous matrix. Energy dispersive X-ray spectroscopy analysis and field emission scanning electron microscopy imaging confirmed the N doping and bentonite impregnation into biochar. X-ray photoelectron spectroscopy analysis revealed that the N atoms were doped interstitially into the carbon matrix of biochar in the form of pyridinic and pyrrolic nitrogen. Simultaneous heteroatom doping and bentonite impregnation reduced the specific surface area to 41.721 m2 g-1 but improved the adsorption capacity of biochar for dye adsorption. Further experimental studies depicted that simultaneous bentonite impregnation and N doping into the biochar matrix is beneficial for direct blue-6 (DB-6) and methylene blue (MB) removal and maximum adsorption capacities of 53.17 mg. g-1 and 41.33 mg. g-1 were obtained for MB and DB-6, respectively, at varying conditions. Adsorption energetics of the dyes with the developed composite portrayed the spontaneity of the process through negative ΔG values. The Langmuir and Freundlich isotherm models fitted the best for MB and DB-6 adsorption. The monolayer adsorption capacity and favourability factor for MB and DB-6 adsorption were calculated to be 54.15 mg. g-1 and 0.217, respectively from the best-fitted isotherms. Based on density functional theory calculations and spectroscopic studies, major interactions governing the adsorption were predicted to be charge-based interactions, π-π interactions, H-bonding, and Lewis acid-base interactions.

Kumquat peel-derived biochar to support zeolitic imidazole framework-67 (ZIF-67) for enhancing peracetic acid activation to remove acetaminophen from aqueous solution

This study presents the synthesis of a novel composite catalyst, ZIF-67, doped on sodium bicarbonate-modified biochar derived from kumquat peels (ZIF-67@KSB3), for the enhanced activation of peracetic acid (PAA) in the degradation of acetaminophen (APAP) in aqueous solutions. The composite demonstrated a high degradation efficiency, achieving 94.3% elimination of APAP at an optimal condition of 200 mg L-1 catalyst dosage and 0.4 mM PAA concentration at pH 7. The degradation mechanism was elucidated, revealing that superoxide anion (O2•-) played a dominant role, while singlet oxygen (1O2) and alkoxyl radicals (R-O•) also contributed significantly. The degradation pathways of APAP were proposed based on LC-MS analyses and molecular electrostatic potential calculations, identifying three primary routes of transformation. Stability tests confirmed that the ZIF-67@KSB3 catalyst retained an 86% efficiency in APAP removal after five successive cycles, underscoring its durability and potential for application in pharmaceutical wastewater treatment.

Zanthoxylum bungeanum Waste-Derived High-Nitrogen Self-Doped Porous Carbons as Efficient Adsorbents for Methylene Blue

In this study, we prepared high-nitrogen self-doped porous carbons (NPC1 and NPC2) derived from the pruned branches and seeds of Zanthoxylum bungeanum using a simple one-step method. NPC1 and NPC2 exhibited elevated nitrogen contents of 3.56% and 4.22%, respectively, along with rich porous structures, high specific surface areas of 1492.9 and 1712.7 m2 g-1 and abundant surface groups. Notably, both NPC1 and NPC2 demonstrated remarkable adsorption abilities for the pollutant methylene blue (MB), with maximum monolayer adsorption capacities of 568.18 and 581.40 mg g-1, respectively. The adsorption kinetics followed the pseudo-second-order kinetics and the adsorption isotherms conformed to the Langmuir isotherm model. The adsorption mechanism primarily relied on the hierarchical pore structures of NPC1 and NPC2 and their diverse strong interactions with MB molecules. This study offers a new approach for the cost-effective design of nitrogen self-doped porous carbons, facilitating the efficient removal of MB from wastewater.

Adsorption of pyrolysis oil model compound (phenol) with plasma-modified hydro-chars and mechanism exploration

Phenol is one of the important ingredients of pyrolysis oil, contributing to the high biotoxicity of pyrolysis oil. To promote the degradation and conversion of phenol during anaerobic digestion, cheap hydro-chars with high phenol adsorption capacity were produced. The phenol adsorption capabilities of the plain hydro-char, plasma modified hydro-char at 25 °C (HC-NH3-P-25) and 500 °C (HC-NH3-P-500) were evaluated, and their adsorption kinetics and thermodynamics were explored. Experimental results indicate that the phenol adsorption capability of HC-NH3-P-500 was the highest. The phenol adsorption kinetics of all samples followed the pseudo-second-order equation and interparticle diffusion model, indicating that the adsorption rate of phenol was controlled by interparticle diffusion and chemistry adsorption simultaneously. By DFT calculations, π-π stacking and hydrogen bond are the main interactions for phenol adsorption. It was observed that an enriched graphite N content decreased the average vertical distance between hydro-chars and phenol in π-π stacking complex, from 3.5120 to 3.4532 Å, causing an increase in the negative adsorption energy between phenol and hydro-char from 13.9330 to 23.4181 kJ/mol. For hydrogen bond complex, the average vertical distance decreased from 3.4885 to 3.3386 Å due to the increase in graphite N content; causing the corresponding negative adsorption energy increased from 19.0233 to 19.9517 kJ/mol. Additionally, the presence of graphite N in the hydro-char created a positive diffusion region and enhanced the electron density between hydro-char and phenol. Analyses suggest that enriched graphite N contributed to the adsorption complex stability, resulting in an improved phenol adsorption capacity.

Carbon nanotube/Chitosan hydrogel for adsorption of acid red 73 in aqueous and soil environments

Acid red 73 is an azo dye, and its residue can pollute the environment and seriously threaten human health and life. In this study, glutaraldehyde was used as the crosslinking agent, chitosan and polyvinyl alcohol were crosslinked under appropriate conditions to obtain a chitosan hydrogel film, and carbon nanotubes were dispersed in the chitosan hydrogel film. The FTIR, XRD, BET, SEM were applied to chatacterize the structure and the morphology of the absorbent and results showed that when the mass fraction of the carbon nanotubes was 1%, the structure was a three-dimensional network with microporous, and the water absorption reached to the maximum value of 266.07% and the elongation at break reached to a maximum of 98.87%. The ability to remove acid red 73 from aqueous and soil environments was evaluated by UV. In the aqueous samples, 70 mg of the adsorbent reached a saturated adsorption capacity of 101.07 mg/g and a removal rate of 92.23% at pH = 5. The thermodynamics conformed with the Langmuir adsorption isotherm and pseudo second-order adsorption kinetic models. In the soil samples, 100 mg of the adsorbent reached an adsorption capacity of 24.73 mg/g and removal rate of 49.45%. When the pH of the soil is between 4 and 7, the removal rate and adsorption capacity do not change much; hence, the pH should be maintained between 5.2 and 6.8, which is extremely suitable for the growth of general plants. Moreover, the experimental results demonstrated that the adsorbent maintained a good removal rate of acid red 73 over six adsorption cycles.

Removal of methylene blue by porous biochar obtained by KOH activation from bamboo biochar

A series of activated biochar (KBBC-700, KBBC-800 and KBBC-900) which were modified by KOH and pyrolysis at various temperatures from ball-milling bamboo powder were obtained. The physicochemical properties and pore structures of activated biochar were investigated by scanning electron microscopy (SEM), fourier transform infrared spectoscopy (FT-IR), X-ray diffraction (XRD) and N2 adsorption/desorption. The adsorption performance for the removal of methylene blue (MB) was deeply studied. The results showed that KBBC-900 obtained at activation temperature of 900 °C exhibited a great surface area which reached 562 m2/g with 0.460 cm3/g of total pore volume. The enhancement of adsorption capacity could be ascribed to the increase of surface oxygen-containing functional groups, aromatization and mesoporous channels. The adsorption capacity was up to 67.46 mg/g under the optimum adsorption parameters with 2 g/L of adsorbent dose, 11 of initial solution pH and 298 K of the reactive temperature. The adsorption capacity was 70.63% of the first time after the material was recycled for three cycles. The kinetics indicated that the adsorption equilibrium time for MB on KBBC-900 was of about 20 min with the data fitted better to the pseudo-second-order kinetics model. The adsorption process was mainly dominated by chemical adsorption. Meanwhile, the adsorption isotherm showed that the Langmuir model fitted the best, and thermodynamic parameters revealed that the adsorption reaction was the endothermic nature and the spontaneous process. Adsorption of MB mainly attributed to electrostatic interactions, cation-π electron interaction and redox reaction. This study suggested that the activated biochar obtained by KOH activation from bamboo biochar has great potentials in the practical application to remove MB from wastewater.

Chitin-derived biochar with nitrogen doping to activate persulfate for phenol degradation: Application potential and electron transfer pathway in system

The fast and efficient removal of organic pollutants (e.g., phenolics) remains one of the focus problems in environment pollution. Thus, a chitin-derived biochar with nitrogen doping (N-BC) was successfully prepared at a lower calcination temperature of 600 °C, which is environmentally friendly and energy saving. The N-BC was analyzed by SEM, FTIR, BET, XRD, XPS and Raman spectroscopy to confirm that the doping of nitrogen element provided sufficient defect sites to promote the activation of persulfate (PDS). Quenching experiments and EPR results revealed the presence of •OH and •O₂^- contributed to phenol degradation in N-BC 600/PDS system. In addition, the linear sweep voltammogram experiments also demonstrated the existence of electron transfer pathway. The electrons were donated from phenol and shifted to PDS through N-BC. The graphitic N and carbon defects in N-BC served as the active sites of the reaction and involved absorption and transfer of electrons as the key character. Moreover, the removal rates of phenol and TOC reached 98.8% and 58.2% within 2 h, indicating that N-BC effectively activated the persulfate to degrade phenol. This study provides the theoretical support and potential applications for the activation of persulfate by nitrogen-doped biochar to degrade other phenolic compounds.

Bamboo-derived nitrogen-doping magnetic porous hydrochar coactivated by K2FeO4 and CaCO3 for phenol removal: Governing factors and mechanisms

In this study, a novel nitrogen-doped magnetic Fe-Ca codoped biochar for phenol removal was successfully fabricated via a hydrothermal and coactivation pyrolysis method. A series of adsorption process parameters (K₂FeO₄ to CaCO₃ ratio, initial phenol concentration, pH value, adsorption time, adsorbent dosage and ion strength) and adsorption models (kinetic models, isotherms and thermodynamic models) were determined using batch experiments and various analysis techniques (XRD, BET, SEM-EDX, Raman spectroscopy, VSM, FTIR and XPS) to investigate the adsorption mechanism and metal-nitrogen-carbon interaction. The biochar with a ratio of Biochar: K₂FeO₄: CaCO₃ = 3:1:1 exhibited superior properties for adsorption of phenol and had a maximum adsorption capacity of 211.73 mg/g at 298 K, C₀ = 200 mg/L, pH = 6.0 and t = 480 min. These excellent adsorption properties were due to superior physicomechanical properties (a large specific surface area (610.53 m²/g) and pore volume (0.3950 cm³/g), a well-developed pore structure (hierarchical), a high graphitization degree (I_D/I_G = 2.02), the presence of O/N-rich functional groups and Fe-Ox,Ca-Ox, N-doping, as well as synergistic activation by K₂FeO₄ and CaCO₃). The Freundlich and pseudo-second-order models effectively fit the adsorption data, indicating multilayer physicochemical adsorption. Pore filling and π-π interactions were the predominant mechanisms for phenol removal, and H-bonding interactions, Lewis-acid-base interactions, and metal complexation played an important role in enhancing phenol removal. A simple, feasible approach with application potential to organic contaminant/pollutant removal was developed in this study.

Bamboo-derived adsorbents for environmental remediation: A review of recent progress

The bamboo family of plants is one of the fastest-growing species in the world. As such, there is an abundance of bamboo residues available for exploitation, especially in southeast Asian, central African and south American regions. The preparation of efficient adsorbents from bamboo residues is an emerging exploitation pathway. Biochars, activated carbons or raw bamboo fibers embedded with nanoparticles, each class of materials has been shown to be highly efficient in adsorption processes. This review aims to summarize recent findings in the application of bamboo-based adsorbents in the removal of organic, inorganic, or gaseous pollutants. Therefore, this review first discusses the preparation methods and surface modification methodologies and their effects on the adsorbent elemental content and other basic properties. The following sections assess the recent progress in the adsorption of heavy metals, organics, and gaseous substances by bamboo-based adsorbents, focusing on the optimum adsorption capacities, adsorption mechanisms and the optimum-fitting kinetic models and isotherms. Finally, research gaps were identified and directions for future research are proposed.

Catalytic degradation of dimethomorph by nitrogen-doped rice husk biochar

N-doped biochar is widely used for activating persulfate to degrade organic pollutants. Which type of N atom is the key factor for activation is still unclear and needs to be further explored and analyzed. In this study, four kinds of biochar were prepared using urea and rice husk as precursors, and tested for the catalytic degradation of dimethomorph. Increasing the nitrogen doping level caused the catalytic removal efficiency of dimethomorph in the presence of peroxymonosulfate increased from 16.6% to 86.8%. A correlation analysis showed that the ability of N-doped biochar to activate PMS is mainly related to the content of pyrrole N, graphite N and carbonyl and the degree of defects. In experiments on electron paramagnetic resonance and free radical suppression, the reactive species of SO₄^•-, ¹O₂,·OH and O₂^.- were detected, among which ¹O₂ was found to be the main agent in the nonradical pathway. The degradation pathways for dimethomorph were analyzed based on a total of 8 degradation products identified by high-performance liquid chromatography-time of flight mass spectrometry (HPLC-Q-TOFMS). The results of this study provide a fundamental basis for using agricultural waste to produce inexpensive and efficient nonmetal catalysts that are highly effective in reducing dimethomorph levels in agricultural lands.

Hierarchical porous biochar from kelp: Insight into self-template effect and highly efficient removal of methylene blue from water

Biochar is known to efficiently remove dyes especially for biochar with hierarchical pores and partial N-species. Here, a facile pyrolysis is used to yield N-doped biochar from kelp without additives, showing surface areas of 771 m2/g as temperature up to 1000 °C and hierarchical small-sized mesopores (2-4 nm) and wide meso-macropores (8-60 nm). A possible self-template mechanism from inorganics is proposed to form hierarchical pore architecture in biochar and used for methylene blue (MB) removal. Biochar pyrolyzed at 1000 °C is found to be efficient for MB removal with uptake of 379.8 mg/g under ambient conditions, one of the largest ever recorded uptakes for other biochar without activation, owing to synergistic effects of high surface areas, mesopores, and graphitized N-species. These results confirm that a facile pyrolysis for transformation of kelp into efficient dyes adsorbent is a cost-effective process for economic and environmental protection.

Synergistic effect of hydrogen bonding and π-π interaction for enhanced adsorption of rhodamine B from water using corn straw biochar

Dyes adsorption to biochar via hydrogen bonding, and π-π interaction alone have attracted much research attention, however, their synergism in adsorption mechanisms remains largely unnoticed. The synergistic effects of the hydrogen bonding and π-π interaction might improve the adsorption capacity and need more understanding to prepare high-capacity biochar. In this work, we evaluated the adsorption of various dyes on biochar prepared via the activation of potassium bicarbonate and urea (named BC-KN) to explore their synergistic effects. Batch experiments indicated the BC-KN showed a high adsorption capacity to rhodamine B at 4839.0 mg/g, azure B at 4477.7 mg/g, and methylene blue at 2223.0 mg/g, respectively. The mechanism of such significant adsorption was investigated by their comparative experiments, characterizations, and computational analyses. The computational analyses suggested that the synergism of the hydrogen bonding and π-π interaction improves the adsorption energies of BC-KN/RhB system from -10.35 kcal/mol to -20.49 kcal/mol. It can be concluded that the hydrogen bonding and π-π interaction can synergize to significantly improve the adsorption by increasing the π-electron density and shortening the distance of aromatic rings, thus dyes with H-donor show significantly better adsorption capacities. The insight of hydrogen bonding being the governing factor in the synergistic system will help produce high-capacity biochar in removing aromatic dyes and suggest a sustainable technology for the efficient decolorization of dye effluent to minimize its damage to the health and environment.

Mechanochemical modified nitrogen-rich biochar derived from shrimp shell: Dominant mechanism in pyridinic-N for aquatic methylene blue removal

N-doping for the preparation of functional carbon materials is a trending research topic. In this study, N-rich biochar (BC) was prepared by calcining naturally N rich shrimp shells under oxygen-limiting environment, and the calcining temperatures were controlled. BC were activated with 5% hydrochloric acid solutions and then post-modified with ball-milling to obtain a series of novel adsorbents (MBCs). All samples were characterized by SEM, BET, FT-IR, XRD, XPS, TG, and element analysis. Surface area, pore volume, and other surface functional groups were significantly improved after acidizing and ball-milling. The adsorption capacities for MB were MBC350 > MBC500 > MBC650 >BC350 > BC650 > BC500, and the equilibrium adsorption capacities were 575.01 mg/g, 506.52 mg/g, 424.59 mg/g, 113.31 mg/g, 93.53 mg/g and 86.25 mg/g, respectively. The excellent adsorption performance of MBCs for MB was ascribed to Lewis acid-base interaction, π-π interaction, electrostatic interaction and van der Waals, and the quinone group and pyridinic-N on the surface of the MBCs are identified as the major active sites. Taken together, ball-milled shrimp shell biochar is a promising material for cation dye adsorption.

One-Step Pyrolysis of Nitrogen-Containing Chemicals and Biochar Derived from Walnut Shells to Absorb Polycyclic Aromatic Hydrocarbons (PAHs)

The pyrolysis of biomass is an efficient means of utilizing biomass resources. Biomass can be converted into various high-performance chemicals and functional materials through pyrolysis. However, current pyrolysis technologies suffer from low conversion rates and single products, so the preparation of nitrogen compounds with high economic value remains a challenge. The walnut shell was soaked in three nitrogen-containing compound solutions before carbonization to produce high-value-added nitrogen-containing chemicals (with a nitrogen content of 59.09%) and biochar for the adsorption of polycyclic aromatic hydrocarbons (PAHs). According to biochar analysis, biochar has a porous structure with a specific surface area of 1161.30 m²/g and a high level of rocky desertification. The surface forms a dense pyrrole structure, and the structure produces π-π interactions with naphthalene molecules, exhibiting excellent naphthalene adsorption with a maximum capacity of 214.98 mg/g. This study provides an efficient, rapid, and environmentally friendly method for producing nitrogen-containing chemicals with high-added value and biochar.

Valorization of Different Fractions from Butiá Pomace by Pyrolysis: H2 Generation and Use of the Biochars for CO2 Capture

This work valorizes butiá pomace (Butia capitata) using pyrolysis to prepare CO2 adsorbents. Different fractions of the pomace, like fibers, endocarps, almonds, and deoiled almonds, were characterized and later pyrolyzed at 700 °C. Gas, bio-oil, and biochar fractions were collected and characterized. The results revealed that biochar, bio-oil, and gas yields depended on the type of pomace fraction (fibers, endocarps, almonds, and deoiled almonds). The higher biochar yield was obtained by endocarps (31.9%wt.). Furthermore, the gas fraction generated at 700 °C presented an H2 content higher than 80%vol regardless of the butiá fraction used as raw material. The biochars presented specific surface areas reaching 220.4 m2 g-1. Additionally, the endocarp-derived biochar presented a CO2 adsorption capacity of 66.43 mg g-1 at 25 °C and 1 bar, showing that this material could be an effective adsorbent to capture this greenhouse gas. Moreover, this capacity was maintained for 5 cycles. Biochars produced from butiá precursors without activation resulted in a higher surface area and better performance than some activated carbons reported in the literature. The results highlighted that pyrolysis could provide a green solution for butiá agro-industrial wastes, generating H2 and an adsorbent for CO2.

Lanthanum carbonate hydroxide/magnetite nanoparticles functionalized porous biochar for phosphate adsorption and recovery: Advanced capacity and mechanisms study

As the increase of global industrial activities, phosphate from industrial wastes such as sewage sludge has become one of the limiting factors for water eutrophication. Herein, lanthanum carbonate hydroxide (La(CO₃)OH)/magnetite (Fe₃O₄) nanoparticles functionalized porous biochar (La/Fe-NBC) with high phosphate adsorption properties is synthesized through molten salt pyrolysis-coprecipitation-hydrothermal multi-step regulation, and further reveal the related processes and mechanisms. La(CO₃)OH functions as active sites for phosphate adsorption, Fe₃O₄ imparts magnetic properties to the composite substance, also porous biochar (NBC) acts as the carrier to prevent the agglomeration of La(CO₃)OH and Fe₃O₄ nanoparticles. The adsorption process of La/Fe-NBC for phosphate fits to the Pseudo-Second Order and Langmuir model, with the theoretical maximum adsorption capacity up to 99.46 mg P/g. And La/Fe-NBC possesses excellent magnetic field (14.50 emu/g), stability, and selectivity, which enables for efficient multiple recovery and reuse. Mechanistic studies have shown that ligand exchange (inner-sphere complexation) between phosphate and carbonate/hydroxyl groups of La(CO₃)OH, and electrostatic attraction play the dominant roles during adsorption process, although susceptible to the solution pH. While co-precipitation is not influenced of pH conditions but with limited contribution to phosphate adsorption. This study may facilitate to optimize the synthesis design of phosphate multi-functional composites for low-carbon and sustainable treatment of industrial phosphate-containing wastes.

N-doped and activated porous biochar derived from cocoa shell for removing norfloxacin from aqueous solution: Performance assessment and mechanism insight

Environmental pollution has worsened as a result of antibiotic overuse. Nitrogen doping of biochar increases its ability to adsorb antibiotics and has been widely applied as an adsorbent. In this study, we synthesized nitrogen-doped biochar (N-A) from cocoa shell wastes calcined with urea and sodium bicarbonate (NaHCO₃) as nitrogen sources and green activators, respectively. An analysis of the biochar morphology, structure, specific surface area, and functional groups provided an understanding of its properties. As indicated by increased surface area, micropores, and surface functional groups, biochar was enhanced in its performance for norfloxacin adsorption when activated using NaHCO₃ and nitrogen doped. Adsorption experiments revealed that N-A biochar at 700 and 400 °C had a high adsorption capacity for NOR of 134 mg/g (N-A-CSB700) and 112.31 mg/g (N-A-CSB400) when compared to pristine biochar at 59.27 mg/g (CSB700) and 56.34 mg/g (CSB400), indicating that N-A doped modification on biochar greatly improved adsorption capacity. The Langmuir model demonstrated better NOR adsorption isotherms. The pseudo-second order and Elovich models closely followed the adsorption kinetics. Further investigations were conducted to determine how environmental factors influence biochar interaction with NOR. The results indicated a stable NOR removal efficiency was kept at a wide pH range, whereas the ionic strength inhibited the NOR adsorption process. The investigation into the sorption mechanism revealed that pore filling, H-bonding, π-π EDA interactions, ion exchange, and electrostatic attraction may all be implicated in the NOR adsorption process. Specifically, pore filling played the dominant role for N-A-CSB700, while N-A-CSB400 sorption occurred mainly via H-bonding. Since N-A-CSB700 doped biochar combines high adsorption capacity with a low inhibition effect of environmental factors (Na⁺/Ca²⁺), it has a high potential for future practical applications as an environmentally sustainable alternative. It uses low-cost solid waste to produce an adsorbent to cope with emerging contaminants such as antibiotics.

N-Doped Biochar from Lignocellulosic Biomass for Preparation of Adsorbent: Characterization, Kinetics and Application

Medulla tetrapanacis is composed of a lignocellulosic biopolymer and has a regular porous structure, which makes it a potential biomass material for preparing porous N-doped biochar. Herewith, N-doped Medulla tetrapanacis biochar (UBC) was successfully prepared by modification with urea and NaHCO₃ under pyrolysis at 700 °C. The nitrogen-containing groups were efficiently introduced into biochar, and the micro-pore structures of the UBC were developed with sizeable specific surface area, which was loaded with massive adsorption sites. The adsorption kinetics and isotherms of the UBC conformed to pseudo-second-order and Langmuir model. The superior adsorption capacities of the UBC for methylene blue (MB) and congo red (CR) were 923.0 mg/g and 728.0 mg/g, and the capacities for Cu²⁺ and Pb²⁺ were 468.5 mg/g and 1466.5 mg/g, respectively. Moreover, the UBC had a stronger affinity for Cr³⁺ and Fe³⁺ in multiple metal ions and retained at a preferable adsorption performance for dyes and heavy metals after five cycles. Precipitation, complexation, and physical adsorption were the main mechanisms of the UBC-adsorbing metal ions and dyes. Thus, lignocellulosic biochar has great potential for removing dyes and heavy metals in aqueous solutions.

Simultaneous Removal of Cu2+, Cd2+ and Pb2+ by Modified Wheat Straw Biochar from Aqueous Solution: Preparation, Characterization and Adsorption Mechanism

As an eco-friendly and efficient adsorbent for removal of potential toxic metals from aqueous solution, biochar has received widespread attention. In the present study, wheat straw biochar (BC) and corresponding modified biochar (HNC) were used to remove Cu²⁺, Cd²⁺ and Pb²⁺ from an aqueous solution. The influence of the environment factors on metals adsorption and adsorption mechanism were discussed in detail. The results showed that the HNC had porous structures and owned ample functional groups (-OH, -COOH and C-N groups) compared with the BC. In the single system, the adsorption capacities of HNC for Cu²⁺, Cd²⁺ and Pb²⁺ at a pH of 5.5 were 18.36, 22.83 and 49.38 mg/g, which were 76.89%, 164.36% and 22.75% higher than that of the BC, respectively. In addition, the adsorption process of Cu²⁺ and Cd²⁺ on BC and HNC fitted to the Langmuir isotherm model and pseudo-second-order kinetics, but the adsorption of Pb²⁺ on BC and HNC fitted to the Langmuir isotherm model and pseudo-first-order kinetics. Adsorption isotherms indicated that the adsorption of Cu²⁺, Cd²⁺ and Pb²⁺ by BC and HNC was a spontaneous endothermic process. The competitive adsorption of mixed metal ions (Cu²⁺, Cd²⁺ and Pb²⁺) revealed that HNC was more preferential to adsorb Cu²⁺ compared with Cd²⁺ and Pb²⁺. Furthermore, Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy analyses revealed that the main adsorption mechanisms were surface complexation and precipitation, and the adsorbed Cu²⁺, Cd²⁺ and Pb²⁺ on HNC mainly exist as CuO, Cd(OH)₂, Pb₃O₄ and Pb(OH)₂.

One-Pot Synthesis of Rubber Seed Shell-Derived N-Doped Ultramicroporous Carbons for Efficient CO2 Adsorption

In this work, a series of novel rubber seed shell-derived N-doped ultramicroporous carbons (NPCs) were prepared by one-step high-temperature activation (500–1000 °C), using melamine as the nitrogen source and KOH as the activator. The effects of the melamine dosage and the activation temperatures on the surface chemical properties (doped N contents and N species), textural properties (surface area, pore structure, and microporosity), CO₂ adsorption capacities, and CO₂/N₂ selectivity were thoroughly investigated and characterized. These as-prepared NPCs demonstrate controllable BET surface areas (398–2163 m²/g), ultramicroporosity, and doped nitrogen contents (0.82–7.52 wt%). It was found that the ultramicroporosity and the doped nitrogens significantly affected the CO₂ adsorption and the separation performance at low pressure. Among the NPCs, highly microporous NPC-600-4 demonstrates the largest CO₂ adsorption capacity of 5.81 mmol/g (273 K, 1.0 bar) and 3.82 mmol/g (298 K, 1.0 bar), as well as a high CO₂/N₂ selectivity of 36.6, surpassing a lot of reported biomass-based porous carbons. In addition, NPC-600-4 also shows excellent thermal stability and recycle performance, indicating the competitive application potential in practical CO₂ capture. This work also presents a facile one-pot synthesis method to prepare high-performance biomass-based NPCs.

Preparation of bamboo-derived magnetic biochar for solid-phase microextraction of fentanyls from urine

In this study, a biochar-based magnetic solid-phase microextraction method, coupled with liquid chromatography-mass spectrometry (LC/MS), was developed for analyzing fentanyl analogs from urine sample. Magnetic biochar was fabricated through an one-step pyrolysis carbonization and magnetization process, followed by an alkali treatment. In order to achieve desired extraction efficiency, feed stocks (wood and bamboo) and different pyrolysis temperatures (300-700 °C) were optimized. The magnetic bamboo biochar pyrolyzed at 400°C was found to have the greatest potential for extraction of fentanyls, with enrichment factors ranging from 58.9 to 93.7, presumably due to H-bonding and π- π interactions between biochar and fentanyls. Various extraction parameters, such as type and volume of desorption solvent, pH, extraction time were optimized, respectively, to achieve the highest extraction efficiency for the target fentanyls. Under optimized conditions, the developed method was found to have detection limits of 3.1-9.4 ng/L, a linear range of 0.05-10 μg/L, good precisions (1.9-9.4% for intra-batch, 2.9-9.9% for inter-batch), and satisfactory recoveries (82.0-111.3%). The developed method by using magnetic bamboo biochar as adsorbent exhibited to be an efficient and promising pretreatment procedure and could potentially be applied for drug analysis in biological samples. This article is protected by copyright. All rights reserved.

Evaluation of sulfuric acid-pretreated biomass-derived biochar characteristics and its diazinon adsorption mechanism

In this study, hemicellulose was mostly removed from biomass (larch and oak) using a sulfuric acid pretreatment. Biochar was then prepared from raw and pretreated biomass using a carbonization process. Biochar derived from pretreated biomass had an aromatic and graphitized structure, and functional groups were observed on the surface. The specific surface area was higher for biochar obtained from pretreated biomass than biochar derived from raw biomass. The biochar obtained from pretreated biomass contained a greater number of micropores than biochar derived from raw biomass. The diazinon removal rate was the highest for biochar that was obtained from pretreated biomass when 10% of the biochar was added to the soil. As a result of the adsorption of diazinon onto the biochar obtained from pretreated biomass, the R² value of the Langmuir isotherm was higher than that of the Freundlich's R².

Biomass-derived carbon-based and silica-based materials for catalytic and adsorptive applications- An update since 2010

Biomass, which defined as plant- or animal-based materials, is intriguing tremendous scientific attentions due to its renewable attribute in serving energy security. Amongst, the plant-based biomasses, particularly those that co-generated in the agriculture activities, are commonly regarded as fuel for burning, which overlooked their hidden potentials for high-end applications. Organically, the plant-based biomass constitutes of lignocellulose components, which can be served as promising precursors for functionalized carbon materials. Meanwhile, its inorganic counterpart made up of various minerals, with Si being the most concerned one. With the advancement of biomass technologies and material synthesis in recent years, numerous attempts were endeavoured to obtain valorised products from biomass. Particularly, syntheses of catalytic and adsorptive materials are actively researched in the field of biomass reutilization. Herein, our work systematically summarized the advancements of biomass-materials for these applications in recent 10 years (2010-2020), with a special focus on the carbon-based and Si-based catalytic/adsorptive materials. Significantly, the deriving steps, inclusive of both pre-treatment and post-treatment of such materials, are incorporated in the discussion, alongside with their significances revealed too. The performance of the as-obtained materials in the respective application is systematically correlated to their physicochemical properties, hence providing valuable insights to the readers. Challenges and promising directions to be explored are raised too at the end of the review, aiming to advocate better-usage of biomass while offering great opportunities to sustain catalysis and adsorption in the industrial scale.

Insights into the mechanism of hydrogen peroxide activation with biochar produced from anaerobically digested residues at different pyrolysis temperatures for the degradation of BTEXS

The disposal of large amounts of biogas residue from anaerobically digested waste is a burden on environment protection. Porous biochars (BCs) were synthesized from biogas residue at three pyrolysis temperatures (300 °C, 550 °C, and 800 °C) and used to catalyze H₂O₂ for the degradation of benzene, toluene, ethylbenzene, xylene isomers (ortho, para, and meta), and styrene (BTEXS) to develop a new use for biogas residues. The prepared BCs were characterized through scanning electron microscopy, Brunauer-Emmett-Teller method, Fourier transform infrared spectrometry, and X-ray photoelectron spectroscopy. Results showed that BC800/H₂O₂ had the highest BTEXS degradation performance over 6 h. The degradation kinetic data were most consistent with the pseudo-second-order model. The different catalytic effect of the three BCs pyrolyzed at different temperatures were attributed to the dominant active sites (C-O/C-OH/C=C/C=O groups, pyridinic N, and graphitic N) that induced the production of reactive oxygen species (ROS). ROS-quenching experiments indicated that the degradation of BTEXS by BC300/H₂O₂, BC550/H₂O₂, and BC800/H₂O₂ involved ∙OH, ∙O₂^-, and ¹O₂. ∙OH was the dominant ROS in BC300/H₂O₂ and BC550/H₂O₂, and ¹O₂ was the dominant ROS in BC800/H₂O₂. Our findings provided new insight into the different catalytic mechanisms for BC production at different pyrolysis temperatures and demonstrated that a porous BC catalyst with high utilization value could be prepared from biogas residue and could hold considerable potential for application in BTEXS treatment in the future.

Formation of nitrogen functionalities in biochar materials and their role in the mitigation of hazardous emerging organic pollutants from wastewater

Emerging organic pollutants (EOPs) are serious environmental concerns known for their prominent adverse and hazardous ecological effects, and persistence in nature. Their detrimental impacts have inspired researchers to develop the strategic tools that reduce and overcome the challenges caused by EOPs' rising concentration. As such, biochar becomes as a promising class of biomass-derived functional materials that can be used as low-cost and environmentally-friendly emerging catalysts to remove EOPs. Herein, in-depth synthetic strategies and formation mechanisms of biochar-based nitrogen functionalities during thermochemical conversion are presented. Most prominently, the factors affecting N-surface functionalities in biochar are discussed, emphasizing the most effective N-doping approach, including intrinsic N-doping from biomass feedstock and extrinsic N-doping from exogenous sources. Moreover, biochar-assisted EOPs removal in line with interactions of nitrogen functionalities and contaminants are discussed. The possible reaction mechanisms, i.e., radical and non-radical degradation, physical adsorption, Lewis acid-base interaction, and chemisorption, driven by N-functionalities, are addressed. The unresolved challenges of the potential applications of biochar-mediated functionalities for EOPs removal are emphasized and the outlooks of future research directions are proposed at the end.

Enhanced adsorption capacity of tetracycline on tea waste biochar with KHCO3 activation from aqueous solution

Activation is an important pathway that can enhance the adsorption capacity of biochar. In this study, a modified tea waste biochar (MTWBC) was prepared via a two-step pyrolysis approach with KHCO₃ activation. Pristine tea waste biochar (TWBC) was also produced as control via one-step pyrolysis without activation. Various characterizations were undertaken to investigate the influence of modification on the morphology, composition, carbon structure, surface area, and functional group of biochar, including scanning electron microscope (SEM), surface area and pore analyzer, element analysis, point of zero charge (pH_PZC), X-ray diffraction, Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). After KHCO₃ activation treatment, the surface area, total pore volume, and micropore volume of MTWBC reached 1981 m²·g^-1, 0.8547 cm³·g^-1, and 0.6439 cm³·g^-1 which were 7.34-fold, 7.27-fold, and 7.30-fold increases, respectively, compared with TWBC. The aromaticity, hydrophilicity, and polarity of the MTWBC increased after modification. More graphitization with less defective structures occurred in MTWBC after modification. The C-, O-, and N-containing groups in MTWBC also changed after the reaction of KHCO₃. The pseudo-second-order and Freundlich models best described the adsorption process on biochar. The maximum adsorption capacity of tetracycline (TC) on MTWBC reached 293.46 mg·g^-1, which was 15-fold more than that of TWBC (19.68 mg·g^-1). An alkaline environment decreased the TC adsorption on biochars. The presence of Na⁺, K⁺, Ca²⁺, and Mg²⁺ inhibited TC adsorption onto biochars. The influence of Cu²⁺ on TC adsorption by biochars depends on its initial concentration. The enhanced adsorption capacity of TC on MTWBC was mainly attributable to the large surface area, the improved pore volume, and more aromatic structure. The adsorption mechanism was based on pore filling and π-π EDA interaction. Therefore, KHCO₃ activated biochar has the potential to remove TC from aquatic environments.

Adsorption and mass transfer studies of methylene blue onto comminuted seedpods from Luehea divaricata and Inga laurina

In this work, comminuted seedpods of the forest species Luehea divaricata (LDPR) and Inga laurina (ILPR) were used as alternative and environmental-friendly adsorbents for the methylene blue (MB) removal from aqueous solutions. Batch adsorption experiments were carried out at the native pH of the solution (pH = 8.7), with curves of removal and adsorption capacity crossed at 0.75 g L^-1, having 125 mg g^-1 for LDPR and 115 mg g^-1 for ILPR. The kinetic models of pseudo-first-order (PFO) and HSDM-Crank were the most adequate to represent MB dye concentration decay data for both biosorbents. The equilibrium curves were better adjusted by the Langmuir model for both adsorbents, with maximum adsorption capacity increased from 279 to 325 mg g^-1 for LDPR, and 199 to 233 mg g^-1 for ILPR, as a function of an increase in temperature from 298 to 328 K. The thermodynamic parameters showed that both systems are spontaneous with a dominance of physisorption. Mass transfer analysis indicates that the external mass transfer is the limiting step, with Bi < 0.5. Surface diffusion increased with the adsorption capacity, presenting linear and exponential behavior for the ILPR and PLPR adsorbents, respectively. Both materials proved to be efficient in treating a simulated effluent with similar industrial wastewater characteristics, reaching superior values at 70% of color removal.

Successful adsorption of bright blue and methylene blue on modified pods of Caesalpinia echinata in discontinuous system

Pods of the forest species Caesalpinia echinata were used as an alternative adsorbent to remove bright blue (BB) and methylene blue (MB) dyes. The raw and acid-treated samples were characterized by techniques like SEM, XRD, and FTIR. The acid-treated pod sample was characterized by an amorphous structure containing several cavities, bumps, and functional groups. The Elovich model was the most satisfactory to describe the adsorption kinetic data. The isothermal studies were better described by the Langmuir model for BB dye, with a maximum capacity of 261 mg g^-1, and Tóth model for MB dye, giving a maximum capacity of 288 mg g^-1. The thermodynamic study indicated a spontaneous and favorable process and endothermic nature for both dyes. In the treatment of two simulated effluents containing a mixture of different compounds such as dyes and salts, to simulate real wastewaters, the adsorbent was highly efficient, presenting around 80% of color removal for both effluents. Therefore, the acid-treated pods of Caesalpinia echinata have great potential to be applied as an alternative adsorbents in treating colored effluents in discontinuous systems.