Surface energy changes and their relationship with the dispersibility of salmeterol xinafoate powders for inhalation after storage at high RH

Using Dry Dispersion Laser Diffraction to Assess Dispersibility in Spheronized Agglomerate Formulations

In this study, dry dispersion laser diffraction was used to study the dispersibility of spheronized agglomerate formulations and identify geometric particle size metrics that correlated well with aerodynamic particle size distribution (APSD). Eleven unique batches of agglomerates were prepared for both laser diffraction and cascade impaction testing. Correlations between the particle size distribution (PSD) and aerodynamic particle size distribution (APSD) metrics for the eleven agglomerate batches were determined in a semi-empirical manner. The strongest correlation between APSD and PSD was observed between the impactor-sized mass (%ISM) and the cumulative PSD fraction <14.5 µm. The strongest correlation with fine particle fraction (FPF) was observed with the cumulative PSD fraction <0.99 micron (R-squared = 0.974). In contrast to the other APSD metrics, good correlations were not found between the mass median aerodynamic diameter (MMAD) and the cumulative PSD fractions. Overall, the implementation of laser diffraction as a surrogate for cascade impaction has the potential to streamline product development. Laser diffraction measurements offer savings in labor and turnaround time compared to cascade impaction.

Ternary Dry Powder Agglomerate Inhalation Formulation of Melatonin With Air Jet Mixing to Improve In Vitro And In Vivo Performance

An improved agglomerate formulation with melatonin and fine lactose for dry powder inhalation using Turbuhaler® was developed. Co-grinding lactose with 1 % magnesium stearate prior to air jet mixing served as a key factor to improve the in vitro aerosolization and in vivo efficacy. Elevated mixing pressure facilitated the dispersion and homogenization of the cohesive mixture for even distribution of agglomerate size after spheroidization and subsequent higher emitted dose with lower variation. Magnesium stearate was employed as a tertiary component to adjust the interparticle force for better aerosolization. At optimized mixing pressure, co-grinding lactose with magnesium stearate before jet mixing displayed further improvement of fine particle fraction to 71.6 ± 3.1 %. The superior fine particle deposition efficiency contributed to rapid onset of action and a high bioavailability of 67.0 % after intratracheal administration to rats. Overall, an inhalable melatonin dry powder formulation exhibiting good aerosol property and lung deposition with clinical translation potential was developed.

Solid Forms of The New Antitrypanosomal 1-(4-Acetamide-Benzenesulfonyl)-Benzimidazole: Preparation and Physicochemical Characterization

This study aimed to investigate the polymorphism of 1-(4-acetamide-benzenesulfonyl)-benzimidazole (PABZI), a newly developed compound with significant activity against Trypanosoma cruzi, the parasite which causes American trypanosomiasis (Chagas disease). Three different crystalline forms of PABZI [a solvent-free form (form I), three isostructural solvates (from isopropanol; acetonitrile-dichloromethane, and methanol-benzene) and a non-isostructural solvate from methanol] were isolated and characterized. The crystal structure of form I was resolved at 173 K and 300 K by single crystal X-ray diffraction. Physicochemical properties, including solubility, dissolution rate, wettability, and solid-state stability were assessed for the two most viable solid forms of PABZI, viz. form I and the isopropanol solvate (PABZI-isoOH). Form I exhibited a higher solubility and dissolution rate, and superior stability towards moisture (40 °C/75 % relative humidity) and UV-Visible light than PABZI-isoOH. Based on the solid-state stability results, form I was selected over PABZI-isoOH for further preclinical studies.

Inhalable dry powder containing remdesivir and disulfiram: Preparation and in vitro characterization

The respiratory tract, as the first and most afflicted target of many viruses such as SARS-CoV-2, seems to be the logical choice for delivering antiviral agents against this and other respiratory viruses. A combination of remdesivir and disulfiram, targeting two different steps in the viral replication cycle, has showed synergistic activity against SARS-CoV-2 in-vitro. In this study, we have developed an inhalable dry powder containing a combination of remdesivir and disulfiram utilizing the spray-drying technique, with the final goal of delivering this drug combination to the respiratory tract. The prepared dry powders were spherical, and crystalline. The particle size was between 1 and 5 μm indicating their suitability for inhalation. The spray-dried combinational dry powder containing remdesivir and disulfiram (RDSD) showed a higher emitted dose (ED) of >88% than single dry powder of remdesivir (RSD) (∼72%) and disulfiram (DSD) (∼84%), with a fine particle fraction (FPF) of ∼55%. Addition of L-leucine to RDSD showed >60% FPF with a similar ED. The in vitro aerosolization was not significantly affected after the stability study conducted at different humidity conditions. Interestingly, the single (RSD and DSD) and combined (RDSD) spray-dried powders showed limited cellular toxicity (CC50 values from 39.4 to >100 µM), while maintaining their anti-SARS-CoV-2 in vitro (EC50 values from 4.43 to 6.63 µM). In a summary, a combinational dry powder formulation containing remdesivir and disulfiram suitable for inhalation was developed by spray-drying technique which showed high cell viability in the respiratory cell line (Calu-3 cells) retaining their anti-SARS-CoV-2 property. In the future, in vivo studies will test the ability of these formulations to inhibit SARS-CoV-2 which is essential for clinical translation.

Improved Aerosolization Stability of Inhalable Tobramycin Powder Formulation by Co-Spray Drying with Colistin

PURPOSE

Tobramycin shows synergistic antibacterial activity with colistin and can reduce the toxic effects of colistin. The purpose of this study is to prepare pulmonary powder formulations containing both colistin and tobramycin and to assess their in vitro aerosol performance and storage stability.

METHODS

The dry powder formulations were manufactured using a lab-scale spray dryer. In vitro aerosol performance was measured using a Next Generation Impactor. The storage stability of the dry powder formulations was measured at 22°C and two relative humidity levels - 20 and 55%. Colistin composition on the particle surface was measured using X-ray photoelectron spectroscopy.

RESULTS

Two combination formulations, with 1:1 and 1:5 molar ratios of colistin and tobramycin, showed fine particle fractions (FPF) of 85%, which was significantly higher than that of the spray dried tobramycin (45%). FPF of the tobramycin formulation increased significantly when stored for four weeks at both 20% and 55% RH. In contrast, FPF values of both combination formulations and spray dried colistin remained stable at both humidity levels. Particle surface of each combination was significantly enriched in colistin molecules; 1:5 combination showed 77% by wt. colistin.

CONCLUSIONS

The superior aerosol performance and aerosolization stability of 1:1 and 1:5 combination formulations of colistin and tobramycin could be attributed to enrichment of colistin on the co-spray dried particle surface. The observed powder properties may be the result of a surfactant-like assembly of these colistin molecules during spray drying, thus forming a hydrophobic particle surface.

Inhaled therapy for COVID-19: Considerations of drugs, formulations and devices

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), the etiological agent responsible for the COVID-19 pandemic, has outspread at full tilt across the world. Although several effective vaccines continue to be deployed, reliable antiviral treatments have yet to be developed against this disease. Currently, available therapeutics for COVID-19 include repurposed, and a few novel drugs. Many drugs have been promising in preclinical studies, but a majority of these drugs have shown little or no efficacy in clinical studies. One of the major reasons is the insufficient drug concentration in the lung, the primary target site of infection for SARS-CoV-2, from the administration of drugs through oral or intravenous routes. Higher effective doses administered through these routes could also lead to adverse side effects. For this reason, inhaled treatments are being tested as an efficient approach for COVID-19, allowing lower doses of drugs ensuring higher concentrations of the drug(s) in the lung. The inhaled treatment combining two or more antiviral drugs will increase potency and reduce the possibility of selecting for SARS-CoV-2 variants with reduced drug susceptibility. Finally, the appropriate drug combination needs to be delivered using a suitable system. Here, we review the current treatment for COVID-19 and their limitations, discussing the advantages of mono and combinational inhaled therapy with a brief outline of the recently reformulated anti-SARS-CoV-2 agents as inhaled formulations. The selection of appropriate delivery devices for inhalation and associated key considerations including the formulation challenges are also discussed.

Amino Acids Improve Aerosolization and Chemical Stability of Potential Inhalable Amorphous Spray-dried Ceftazidime for Pseudomonas aeruginosa Lung Infection

Pseudomonas aeruginosa infection is common in cystic fibrosis as well non-cystic fibrosis bronchiectasis. The pathogen presents challenges for treatment due to its adaptive antibiotic-resistance, mainly pertaining to its biofilm-forming ability, as well as limitations associated with conventional drug delivery in achieving desired therapeutic concentration in the infection site. Hence, therapeutic approach has shifted towards the inhalation of antibiotics. Ceftazidime is a potent antibiotic against the pathogen; however, it is currently only available as a parenteral formulation. Here, spray-dryer was employed to generate inhalable high dose ceftazidime microparticles. In addition, the use of amino acids (valine, leucine, methionine, phenylalanine, and tryptophan) to improve aerosolization as well as chemical stability of amorphous ceftazidime was explored. The particles were characterized using X ray diffraction, infrared (IR) spectroscopy, calorimetry, electron microscopy, particle size analyzer, and next generation impactor. The chemical stability at 25 °C/<15% was assessed using chromatography. All co-spray dried formulations were confirmed as monophasic amorphous systems using calorimetry. In addition, principal component analysis of the IR spectra suggested potential interaction between tryptophan and ceftazidime in the co-amorphous matrix. Inclusion of amino acids improved aerosolization and chemical stability in all cases. Increase in surface asperity was clear with the use of amino acids which likely contributed to the improved aerosol performance, and potential interaction between amino acids and ceftazidime was plausibly the reason for improved chemical stability. Leucine offered the best aerosolization enhancement with a fine particle fraction of 78% and tryptophan showed stabilizing superiority by reducing chemical degradation by 51% over 10 weeks in 1:1 molar ratio. The protection against ceftazidime degradation varied with the nature of amino acids. Additionally, there was a linear relationship between degradation protection and molar mass of amino acids or percentage weight of amino acids in the formulations. None of the amino acids were successful in completely inhibiting degradation of ceftazidime in amorphous spray-dried powder to prepare a commercially viable product with desired shelf-life. All the amino acids and ceftazidime were non-toxic to A549 alveolar cell line.

Multifunctional Role of Silica in Pharmaceutical Formulations

Due to the high surface area, adjustable surface and pore structures, and excellent biocompatibility, nano- and micro-sized silica have certainly attracted the attention of many researchers in the medical fields. This review focuses on the multifunctional roles of silica in different pharmaceutical formulations including solid preparations, liquid drugs, and advanced drug delivery systems. For traditional solid preparations, it can improve compactibility and flowability, promote disintegration, adjust hygroscopicity, and prevent excessive adhesion. As for liquid drugs and preparations, like volatile oil, ethers, vitamins, and self-emulsifying drug delivery systems, silica with adjustable pore structures is a good adsorbent for solidification. Also, silica with various particle sizes, surface characteristics, pore structure, and surface modification controlled by different synthesis methods has gained wide attention owing to its unparalleled advantages for drug delivery and disease diagnosis. We also collate the latest pharmaceutical applications of silica sorted out by formulations. Finally, we point out the thorny issues for application and survey future trends pertaining to silica in an effort to provide a comprehensive overview of its future development in the medical fields. Graphical Abstract.

Co-Amorphization of Kanamycin with Amino Acids Improves Aerosolization

Different formulation techniques have been investigated to prepare highly aerosolizable dry powders to deliver a high dose of antibiotics to the lung for treating local infections. In this study, we investigated the influence of the co-amorphization of a model drug, kanamycin, with selected amino acids (valine, methionine, phenylalanine, and tryptophan) by co-spray drying on its aerosolization. The co-amorphicity was confirmed by thermal technique. The physical stability was monitored using low-frequency Raman spectroscopy coupled with principal component analysis. Except for the kanamycin-valine formulation, all the formulations offered improved fine particle fraction (FPF) with the highest FPF of 84% achieved for the kanamycin-methionine formulation. All the co-amorphous formulations were physically stable for 28 days at low relative humidity (25 °C/<15% RH) and exhibited stable aerosolization. At higher RH (53%), even though methionine transformed into its crystalline counterpart, the kanamycin-methionine formulation offered the best aerosolization stability without any decrease in FPF. While further studies are warranted to reveal the underlying mechanism, this study reports that the co-amorphization of kanamycin with amino acids, especially with methionine, has the potential to be developed as a high dose kanamycin dry powder formulation.

High dose dry powder inhalers to overcome the challenges of tuberculosis treatment

Tuberculosis (TB) is a major global health burden. The emergence of the human immunodeficiency virus (HIV) epidemic and drug resistance has complicated global TB control. Pulmonary delivery of drugs using dry powder inhalers (DPI) is an emerging approach to treat TB. In comparison with the conventional pulmonary delivery for asthma and chronic obstructive pulmonary disease (COPD), TB requires high dose delivery to the lung. However, high dose delivery depends on the successful design of the inhaler device and the formulation of highly aerosolizable powders. Particle engineering techniques play an important role in the development of high dose dry powder formulations. This review focuses on the development of high dose dry powder formulations for TB treatment with background information on the challenges of the current treatment of TB and the potential for pulmonary delivery. Particle engineering techniques with a particular focus on the spray drying and a summary of the developed dry powder formulations using different techniques are also discussed.

Difference in resistance to humidity between commonly used dry powder inhalers: an in vitro study

Multi-dose dry powder inhalers (DPIs) are commonly used in asthma and chronic obstructive lung disease (COPD) treatment. A disadvantage is their sensitivity to humidity. In real life, DPIs are periodically exposed to humid conditions, which may affect aerosol characteristics and lung deposition. This study compared DPI aerosol performance after exposure to humidity. Budesonide (BUD) inhalers (Turbuhaler; Novolizer; Easyhaler) and budesonide/formoterol (BUD/FORM) inhalers (Turbuhaler; Spiromax; Easyhaler) were stored in 75% relative humidity (RH) at both ambient temperature and at -0 °C. Delivered dose (DD) and fine-particle dose (FPD) were tested in vitro before and after storage. BUD inhalers: Turbuhaler and Novolizer showed only small decreases (<15%) in FPD in 40 °C/75% RH, whereas FPD for Easyhaler decreased by >60% (P=0.01) after 1.5 months of storage. Easyhaler also decreased significantly after 6 months of storage in ambient/75%RH by 25% and 54% for DD and FPD, respectively, whereas only small decreases were seen for Turbuhaler and Novolizer (<15%). BUD/FORM inhalers: Turbuhaler and Spiromax DD were unchanged in 40 °C/75% RH, whereas Easyhaler showed a small decrease. FPD (budesonide) decreased for Turbuhaler, Spiromax and Easyhaler by 18%, 10% and 68% (all significant), respectively, at 40 °C/75% RH. In ambient/75%RH, DD was unchanged for all inhalers, whereas FPD (budesonide) decreased for Spiromax (7%, P=0.02) and Easyhaler (34%, (P<0.01)). There are significant differences in device performance after exposure to humid conditions. A clinically relevant decrease of more than half FPD was seen for one of the inhalers, a decrease that may affect patients' clinical outcomes. Prescriber and patient knowledge on device attributes are essential to ensure optimal drug delivery to the lungs.

On the effects of blending, physicochemical properties, and their interactions on the performance of carrier-based dry powders for inhalation - A review

Blending drug and carrier powders to produce homogeneous drug-carrier adhesive mixtures is a key step in the production of dry powder inhaler (DPI) formulations. Although the blending conditions can result in different conclusions or probably change the outcome of a study entirely if being selected differently, there is a scarcity of data on the influence of blending processes on the physicochemical properties of bulk powder formulations and the follow-on effects on DPI performance. This paper provides an overview of the interactions between variables related to blending conditions (e.g. blending equipment, time, speed and sequence as well as environmental humidity) and powder physicochemical properties (e.g. size distribution, shape distribution, density, anomeric composition, electrostatic charge, surface, and bulk properties), and their effects on the performance of adhesive mixtures for inhalation in terms of drug content homogeneity, drug-carrier adhesion, and drug aerosolisation behaviour. The relevance of carrier payload, batch size and segregation was also discussed. Challenges and future directions were identified. This review therefore contributes towards a better understanding of the blending process, powder physicochemical properties, and their interlinked effects on the fundamental understanding of adhesive mixtures for inhalation. The knowledge gained is essential to ensure optimum blending and thereby controlled functionality of DPIs.

Towards a more desirable dry powder inhaler formulation: large spray-dried mannitol microspheres outperform small microspheres

PURPOSE

To investigate, for the first time, the performance of a dry powder inhaler (DPI, Aerolizer(®)) in the case of a model drug (i.e. albuterol sulphate) formulated with spray dried mannitol carrier particles with homogeneous shape and solid-state form but different sizes.

METHODS

Spray dried mannitol (SDM) particles were characterized in terms of size, surface area, morphology, water content, solid-state, density and electrostatic charge by a novel approach. DPI formulations composed of SDM and albuterol sulphate (AS) were prepared and evaluated in terms of drug content homogeneity and in vitro aerosolization performance.

RESULTS

All SDM particles generated similar fine particle fractions of AS. Formulations consisting of larger SDM particles demonstrated better drug content homogeneity, reduced amounts of drug loss and reduced oropharyngeal deposition. Comparing different SDM products demonstrated that SDM powders with relatively poorer flowability, wider size distributions and higher charge density generated DPI formulations with poorer drug content homogeneity and deposited higher amount of drug on the inhaler, mouthpiece adaptor and throat. DPI formulation total desirability increased linearly with the mean diameter of SDM.

CONCLUSION

Particle shape and solid-state form of mannitol could dominate over carrier size, bulk density, flowability and charge in terms of determining the aerosolization behaviour of AS formulated with mannitol carrier, at least within the experimental protocols applied in the present study.

Triggering effect of N-acetylglucosamine on retarded drug release from a lectin-anchored chitosan nanoparticles-in-microparticles system

The aim of this study was to investigate the use of N-acetylglucosamine (NAG) to accelerate drug release from a lectin-modified carrier. A wheat germ agglutinin (WGA)-anchored salmeterol xinafoate (SalX)-loaded nanoparticles-in-microparticles system (NiMS) was prepared with an ionotropic gelation technique combined with a spray drying method. The formulated microparticles were spherical, with diameters ranging mainly from 2 to 8 μm; the drug entrapment efficiency was >70% (w/w), and the loading capacity was approximately 8% (w/w). Drug release from WGA-SalX-NiMS, within the first 4h, was approximately 30% less than that from SalX-NiMS, indicating an effect of lectin-modification to retard drug release from the NiMS. Due to "sugar-lectin" interactions, drug release from WGA-SalX-NiMS was substantially increased after the addition of NAG to the release medium. However, no significant influence of NAG was observed on the drug release profile of SalX-NiMS without WGA anchorage. The characteristics of NAG-WGA interaction may provide valuable insights into the "triggering-effects" of specific sugars on drug release from lectin-anchored carriers. These results suggest that it is possible to control drug release from a lectin-anchored drug delivery system using a specific sugar, and that the designed novel WGA-SalX-NiMS may be a suitable formulation for chronotherapy of asthma.

Rapid characterisation of the inherent dispersibility of respirable powders using dry dispersion laser diffraction

Understanding and controlling powder de-agglomeration is of great importance in the development of dry powder inhaler (DPI) products. Dry dispersion laser diffraction measures particle size readily under controlled dispersing conditions, but has not been exploited fully to characterise inherent powder dispersibility. The aim of the study was to utilise particle size-dispersing pressure titration curves to characterise powder cohesivity and ease of de-agglomeration. Seven inhaled drug/excipient powders (beclometasone dipropionate, budesonide, fluticasone propionate, lactohale 300, salbutamol base, salmeterol xinafoate and tofimilast) were subjected to a range of dispersing pressures (0.2-4.5 Bar) in the Sympatec HELOS/RODOS laser diffractometer and particle size measurements were recorded. Particle size-primary pressure data were used to determine the pressures required for complete de-agglomeration. The latter were employed as an index of the cohesive strength of the powder (critical primary pressure; CPP), and the curves were modelled empirically to derive the pressure required for 50% de-agglomeration (DA₅₀). The powders presented a range of CPP (1.0-3.5 Bar) and DA₅₀ (0.23-1.45 Bar) which appeared to be characteristic for different mechanisms of powder de-agglomeration. This approach has utility as a rapid pre-formulation tool to measure inherent powder dispersibility, in order to direct the development strategy of DPI products.

Characterising surface energy of pharmaceutical powders by inverse gas chromatography at finite dilution

Objectives

The objectives of this project were the use of surface energy distributions in: distinguishing the effects of magnesium stearate on the surface energy of lactose processed by two methods: mixing in a Turbula and mechanofusion; characterising surface energy of materials before and after micronisation; and understanding surface energy changes of micronised lactose before and after storage at high relative humidity (RH).

Methods

Heptane, octane and nonane were used to determine nonpolar surface energy, and dichloromethane and ethyl acetate were used to determine polar surface energy in inverse gas chromatography at finite dilution.

Key findings

The total surface energy of lactose decreased more after mechanofusion with magnesium stearate than mixing in Turbula. The nonpolar surface energy of indometacin increased while polar and total surface energies decreased after micronisation. The nonpolar, polar and total surface energies and work of cohesion of micronised lactose decreased after storage at 75%RH for three months.

Conclusions

The surface energy distributions determined at finite dilution successfully distinguished and revealed more information than infinite dilution on surface energy changes in materials undergoing different pharmaceutical processes such as mixing, mechanofusion, micronisation and storage at high RH.

Lactose characteristics and the generation of the aerosol

The delivery efficiency of dry-powder products for inhalation is dependent upon the drug formulation, the inhaler device, and the inhalation technique. Dry powder formulations are generally produced by mixing the micronised drug particles with larger carrier particles. These carrier particles are commonly lactose. The aerosol performance of a powder is highly dependent on the lactose characteristics, such as particle size distribution and shape and surface properties. Because lactose is the main component in these formulations, its selection is a crucial determinant of drug deposition into the lung, as interparticle forces may be affected by the carrier-particle properties. Therefore, the purpose of this article is to review the various grades of lactose, their production, and the methods of their characterisation. The origin of their adhesive and cohesive forces and their influence on aerosol generation are described, and the impact of the physicochemical properties of lactose on carrier-drug dispersion is discussed in detail.